Proposal PROJECT MANUAL P R O P E R T Y M A N A G E M E N T F A L L O N C O U N T Y. Baker, MT P.O. Box 846

Transcription

1 PROJECT MANUAL P R O P E R T Y M A N A G E M E N T F A L L O N C O U N T Y Proposal P.O. Box 846 Baker, MT P R E C A S T R E I N F O R C E D C O N C R E T E B O X C U L V E R T F O R W E S T M O R E A N D D R Y F O R K R O A D S Project No.: M13B199 & M13B53

2

3 QUOTE Proposal of (hereinafter called "BIDDER"), organized and existing under the laws of the State of, doing business as * to the Fallon County commission (hereinafter called "OWNER"). In compliance with your Advertisement for Quotes, BIDDER hereby proposes to Fabricate, Store, & Deliver various PRECAST REINFORCED CONCRETE BOX CULVERTS WITH END SECTIONS; in strict accordance with the CONTRACT DOCUMENTS, within the time set forth therein, and at the prices stated below. By submission of this QUOTE, each BIDDER certifies and in the case of a joint QUOTE, each party thereto certifies as to his own organization, that this QUOTE has been arrived at independently, without consultation, communication, or agreement as to any matter relating to this QUOTE with any other BIDDER or with any competitor. The Precast Reinforced Concrete Box Culvert shall be completed and available for delivery by July 1, BIDDER acknowledges receipt of the following ADDENDUM: *Insert Corporation, Partnership, or Individual, as applicable.

4 BIDDER agrees to perform all the work described in the CONTRACT DOCUMENTS for the following unit prices or lump sum: NOTE: QUOTE shall include shipping, sales tax, and all other applicable taxes and fees. Bidder may provide quote for Schedule I, Schedule II, or both. Owner reserves the right to award one, both, or neither Schedules. Award will be made to the lowest responsible Bidder for each Schedule. SCHEDULE I WESTMORE REINFORCED CONCRETE BOX CULVERT ITEM DESCRIPTION UNIT UNIT PRICE EXTENDED PRICE 1. SINGLE 14 X 11 PRECAST RCB CULVERT 2. SINGLE 14 X 11 PRECAST RCBC END SECTION 198 FT 6 EACH TOTAL $ SCHEDULE II DRY FORK ROAD REINFORCED CONCRETE BOX CULVERT ITEM DESCRIPTION UNIT UNIT PRICE EXTENDED PRICE 1. SINGLE 14 X 14 PRECAST RCB CULVERT 2. SINGLE 14 X 14 PRECAST RCBC END SECTION 3. DBL 14 X 14 PRECAST RCB CULVERT 4. DBL 14 X 14 PRECAST RCBC END SECTION 52 FT 2 EACH 52 FT 2 EACH TOTAL $

5 Respectfully submitted: Signature Address Title Date License Number (If Applicable) (SEAL * If QUOTE is by a Corporation) Attest:

6 SPECIFICATIONS The Precast Reinforced Concrete Box Culverts shall conform to requirements as specified in the Standard Specifications for Road and Bridge Construction of the Montana Department of Transportation, 2014 Edition. DESIGN MIX OF CONCRETE 1. The design minimum 28 day compressive strength of concrete shall be as per fabricator s design, however shall not be less than 4,500 psi. 2. Type V Cement shall be used. GENERAL NOTES Design shall be in accordance with Section 554 of the Specifications, with the following criteria: 1. Box culvert and box culvert end section design shall conform to the AASHTO LRFD Bridge Designs Specifications, 2014 Edition with 2015 interims. 2. Design Live Load: HL The design of the barrel sections shall be based on a minimum fill height of 1 foot and include all subsequent fill heights up to and including the maximum fill height of 5 foot over the box culvert. 4. Minimum inside corner fillet shall be 6 inches. 5. Minimum precast barrel section length shall be 4 feet. 6. The Contractor shall stencil the structure with the date of construction. 7. Contractor shall provide a minimum of four (4) Galvanized Hidden Tie Bolts for between each end section and each full barrel section of the RCB Culvert. 8. Contractor shall provide Galvanized Sleeves, Type IV Epoxy, and #5 Epoxy Coated Rebar 16 inches in length in floor of box for cutoff walls. Galvanized Sleeves shall be cast into the upstream and downstream most end sections with a minimum of five (5) Sleeves required per barrel section at the upstream and downstream ends. 9. Contractor shall provide EZ-STIK Joint Sealant by Press-Seal for all joints. 10. Contractor shall provide Sealwrap Primer and Sealwrap by Mar Mac for all joints, lifting holes, and pulling holes.

7 11. Contractor shall provide Non-shrink Grout for all lifting and pulling holes. 12. Contractor shall provide Panel Hooks, Eye Bolts, and Concrete Inserts for the RCB Culvert as shown on the Fence Anchor Details. 13. Cutoff Walls and Parapets shall be provided as shown on the General Layout Drawing and included with the quote price per each for the various types of End Section. DELIVERY AND STORAGE 1. All costs for storage, loading, transporting, and delivery to the project site shall be included in the quote for the Precast Concrete Box Culvert. SHOP PLANS 1. The fabricator shall submit shop drawings in accordance with the specifications to Brosz Engineering Inc., PO Box 357, Bowman, ND for review. Include design and check design with initial submittal. After review, corrections (if necessary), and approval by Brosz Engineering Inc., the Engineer will authorize fabrication.

8

9

10

11

12