SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP

Size: px
Start display at page:

Download "SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP"

Transcription

1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of providing all work, materials, labor, equipment, and supervision necessary to provide a fully functioning softball field fence and gate and backstop pole and net installation as provided for in these specifications and on the drawings. Included are the following topics: PART 1 - GENERAL Scope Related Work Reference Submittals Qualifications PART - MATERIALS General Backstop Poles Backstop Net Backstop Cabling Fence Height Fence Fabric Fence Fabric Fasteners Fence Framing Schedule of Fencing Materials Schedule of Gate Materials Fence Gates Fence Gate Hardware Fence Post Tops Fence Tension Wire Fence Stretcher Bars Fence Ground Rods Concrete PART - EXECUTION Site Work Concrete Footings Backstop Poles and Cabling Fence Posts and Braces Fence Post Bracing Assembly Fence Stretcher Bars Fence Ground Rods Fence Fabric Fence Grade Clearance Fence Gates Cleanup RELATED WORK Applicable provisions of Division 1 govern work under this Section Common Work Results for Exterior Improvements 1 1-1

2 REFERENCE Unless otherwise specified in these specifications or otherwise shown on the drawings, conform all work under this section to Section.. of the Wisconsin Department of Transportation, Standard Specifications for Highway and Structure Construction, current edition. SUBMITTALS Shop Drawings: Submit shop drawings for fence, gates, backstop, and appurtenances. Include plan layout; fence height; location and sizes of posts, rails, braces, gates and footings; product data; and erection procedures. Samples: Submit fabric, netting, and post samples, approximately -in. long or -in. square, for verification of polymer coating color. Installer Qualifications: Submit documentation of the installer qualifications specified below. QUALIFICATIONS Fence and backstop installer shall have a minimum of five years experience with a minimum of five layouts and installations of softball/baseball field fencing and backstops similar to this project. P A R T - M A T E R I A L S GENERAL All materials furnished shall be new materials unless otherwise specified. Salvaged materials may be used only when specified. All fence and backstop material is to be colored black. BACKSTOP POLES Provide -/ in., Schedule 0, steel pipe with black mil finish for supporting the backstop netting. Poles shall measure 0 ft from the finished field. Provide steel dome cap for each pole. BACKSTOP NETTING Provide # twisted, knotted polyethylene netting with rope border. # breaking strength. Color: Black. Include additional UV treatment. BACKSTOP CABLE Provide all hardware for top, vertical and bottom cabling for backstop. Top Cable: 1/-in. galvanized steel cable with associated hardware of cable ends, eye bolts, and turnbuckles to tension top cable from Pole to pole. Bottom Cable: 1/-in. galvanized steel cable with associated hardware of cable ends, self-tapping eye hooks and turnbuckles to tension lower cable to tension cable pole to pole along the top of the concrete wall. Vertical Cable: /-in. galvanized steel cable with associated hardware of cable ends, self-taping eye hooks and turnbuckles to tension cable from top of pole to top of concrete wall. FENCE HEIGHT The height of the fence shall be as shown on the plans or specified. The designated height of the fence shall be the fabric height. FENCE FABRIC Provide gauge steel core, two () inch mesh fabric, with knuckled selvage on bottom. Fabric shall be polymer-coated, fusion bonded, ASTM F, Class b, over galvanized, aluminum coated, or zinc aluminum alloy coated steel wire. Color of coating shall be black complying with ASTM F

3 1 1 1 FENCE FABRIC FASTENERS Provide fabric fasteners of steel wire clips and tie wires galvanized in accordance with ASTM A-1, Class III, or aluminum coated in conformance with ASTM A-1. Provide fasteners for posts, top and intermediate rails, bottom rails, top tension wires and braces of gauge steel or 0. inch diameter aluminum tie wires. Provide fasteners for bottom tension wire of not smaller than gauge or 0.1 inch diameter aluminum tie wires. FENCE FRAMING Furnish posts and rails in accordance with the following schedules for the fence heights indicated on the Drawings. All fence shall have a top rail. Posts and rails shall have mil polymer coating over galvanized or zinc aluminum alloy coated steel. Color of coating shall be black complying with ASTM F. SCHEDULE OF FENCING MATERIALS MIN. MIN. MIN. MAX. TYPE SIZE WALL YIELD WGT POST AND O.D. THICK STRENGTH (LBS/ SPACE HEIGHT POST TYPE (IN) (IN) (PSI) FT.) (FT.) Line and Corner Posts SS ,000. Top Rails SS , Gate Posts shall conform to manufacturer's specifications for various width gates. Minimum sizes shall be as follows: SCHEDULE OF GATE MATERIALS MIN. MIN. MIN. TYPE SIZE WALL YIELD WGT AND O.D. THICK STRENGTH (LBS/ HEIGHT POST TYPE (IN) (IN) (PSI) FT.) Gate Posts (Leaf Width Six Feet or Less) SS ,000. Gate Frames SS ,

4 FENCE GATES Provide additional horizontal and vertical members as necessary to assure proper gate operation and attachment to fabric and hardware. Provide welded frames where corner rigidity is not sufficient to prevent sag. Gate frames shall be covered with the same fabric as the fence. Weld to provide rigid connections. Install fabric with stretcher bars at vertical edges. Attach to frame at fifteen (1) inches o.c. all sides.. FENCE GATE HARDWARE Provide heavy duty hinges of malleable iron, pressed or forged steel, non-lift-off type, adjusted to permit 0 degree gate opening. Provide two () hinges for each leaf. Provide heavy duty forked type or plunger bar type latches for all single leaf gates. Provide center stop and keeper for all double leaf gates. Provide spring latch for all sliding gates. Provide padlock eye as an integral part of all latches. FENCE POST TOPS Provide loop tops for inline posts. Provide dome tops for terminal, corner, and gate posts. FENCE TENSION WIRE Provide gauge tension wire conforming to the fence fabric used, complete with end clamps. Tension wire shall be polymer-coated to match fence fabric. FENCE STRETCHER BARS Provide stretcher bars of one piece lengths equal to the full fabric height with a minimum cross section of /" x /". Provide one (1) stretcher bar for each gate and end post and two () for each corner and pull post, except roll form posts with integral loops. FENCE GROUND RODS Provide a one-half inch diameter six () foot long copper clad rod to provide a ground. Provide one (1) for each 1,000' of fence, one for each separated fence section, and one for softball backstop. CONCRETE All concrete for post and pole base construction shall be Class BB concrete in accordance with Section P A R T - E X E C U T I O N SITE WORK Prior to fence construction remove and dispose of all trees, brush, logs, stumps and other debris for a width of at least twelve () inches each side of the proposed fence alignment. CONCRETE FOOTINGS Excavate holes for footings to neat dimensions in firm ground to insure the post will be centered. Remove rock or other obstructions encountered to the required depth. Use forms in unstable soil and allow them to remain in place for at least twenty-four () hours after concrete is poured. Backfill, after forms are removed, with suitable material thoroughly compacted in place in layers to prevent settlement

5 Backstop footings shall be seventy two () inches deep and twenty four () inches diameter. The top of the footing shall be set below finish grade of the field as shown on the Drawings. Chain link fence footings shall be thirty-six () inches deep and ten () inches minimum diameter. The bottom of the post shall be three () inches above the bottom of the hole. Corner, gate and end post bases shall be twelve () inches minimum diameter. Concrete bases shall be below grade at the post and have a smooth troweled finish. All softball field perimeter fencing shall be finished with an -in. concrete mow strip. Internal fencing without the mow strip shall have the footing tops held -in. below finish grade. Concrete footings shall cure for seven () days before placing tension wires. BACKSTOP POLES AND CABLING Set poles to be vertical at tensioning. The outside poles shall remain plumb with top cable fully tensioned and netting secured to cable. Set the top of the poles to 0 feet above finish field elevation. A concrete wall matching the finished height of the elevated bleacher catwalk shall butt up to each of the backstop pole. Set top cable with treaded eyehooks. Other eyehooks are to be self-tapping. Properly tension cables prior to setting the protective netting. FENCE POSTS AND BRACES Set posts in a vertical position at the required location and alignment. Set tops at the required elevation to provide a smooth profile at the top rail or tension wire without abrupt changes and in conformity with the general contour and which meets the approval of the Engineer. Place an end post at each end of each run of fence. Place a corner post whenever a break of 0 degrees or more occurs in the horizontal alignment. Set an intersection post in line with an intersecting chain link fence and brace it to the adjacent posts of the intersecting fence. Place an intermediate braced post where the vertical alignment changes by more than degrees, or a change in fence grade of more than nine () percent occurs. Where driven posts are specified, all end, corner, gate, and brace (pull) posts must be set in concrete. Driven posts shall be driven a minimum of thirty-two () inches into undisturbed soil. FENCE POST BRACING ASSEMBLY Post bracing assemblies consist of one (1) or more brace rails and a three-eighths (/) inch truss rod as hereafter specified. Provide brace rails the same size as the top rail. Provide truss rods with an adjustable take-up adapter. Install a single bracing assembly at each gate and end post location. Install a double bracing assembly at each corner post and all intermediate braced posts. Provide the bracing assembly with one horizontal brace rail and one (1) diagonal truss rod on all fences which have a top rail. Locate the horizontal brace rail in accordance with the manufacturer's specifications. FENCE STRETCHER BARS Provide one (1) stretcher bar for each gate and end post and two () for each corner and pull post, except roll form posts with integral loops. Attach to posts with heavy duty pressed steel or malleable iron bands spaced at fifteen (1) inches o.c. FENCE GROUND RODS Connect at least three () fence wires to the ground rod by clamping, bolting or brazing. Ground rod shall be installed on line with fence

6 Install ground rods as specified for each run of fence and install additional rods for each 1,000' on long runs of fence. FENCE FABRIC Install, stretch, and anchor tension wires to each end, corner, gate and brace post and properly attach to each line post before the fabric is placed. Pass top tension wire thru the post top rail opening. Install top, intermediate and bottom rails at proper locations. Hang fabric on the inside (playing side) of all installations. Attach the end of the fabric to the end, corner, gate or brace posts (except roll form posts with integral loops) by means of a stretcher bar threaded through the end loops of the fabric and stretched to remove all slack with proper stretching equipment. Secure the stretched fabric to posts, rails and tension wires with specified fabric fasteners. Install fabric fasteners on all posts at not greater than fourteen (1) inches o.c. and on rails and bottom tension wires at not more than twenty-four () inches o.c. Where a top tension wire is installed, fasten to the fabric at not more than eighteen () inches o.c. Repeat stretching operations at approximately every 0' for each run of fence. Make splices in fabric by interweaving a wire picket through each end loop of each piece of fabric. Each splice shall be subject to the Engineers approval. FENCE GRADE CLEARANCE For softball diamond provide a clearance from the bottom of the fabric to the concrete mow edge of one (1) inch. FENCE GATES Install gates plumb and level and adjust for smooth operation as intended, without binding or hanging up. CLEANUP After chain link fence construction is completed clean up all storage and work areas. Replace or repair as required all landscape features damaged or disturbed under this contract. END OF SECTION 1 1 -

Item 550 Chain Link Fence

Item 550 Chain Link Fence Item Chain Link Fence 1. DESCRIPTION 2. MATERIALS Furnish, install, remove, repair, or replace chain link fence and gates. Furnish certification from the chain link fence materials manufacturer stating

More information

WAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence

WAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised

More information

Project: # Solano Community College District

Project: # Solano Community College District ADDENDUM #02 Project: #16 007 Solano Community College District Horticulture Site Improvements Date: April 26, 2016 The following clarifications are provided based on questions received or changes in District

More information

Testing. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified.

Testing. Material testing will be according to applicable AASHTO, ASTM or Department methods as specified. 907.01 Section 907. FENCING MATERIALS 907.01 General Requirements. Materials for use in fencing property, right-of-way and other installations must comply with this section. 907.02 Testing. Material testing

More information

SECTION CHAIN LINK FENCING

SECTION CHAIN LINK FENCING SECTION 32 31 13 CHAIN LINK FENCING PART 1 - GENERAL 1.01 SECTION INCLUDES A. The Work specified in this Section consists of furnishing and installing permanent chain link fences and gates in accordance

More information

City of Regina Standard Construction Specification SECTION 2660 CHAIN LINK FENCE

City of Regina Standard Construction Specification SECTION 2660 CHAIN LINK FENCE 1.0 GENERAL 1.1 Scope 1.1.1 The work shall consist of supply and installing chain link fence, including braces and gates, as shown on the plans and specifications at the locations designated by the Engineer.

More information

PART MATERIALS. Section Fencing Materials. Description

PART MATERIALS. Section Fencing Materials. Description PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain

More information

SECTION CHAIN LINK FENCING AND GATES

SECTION CHAIN LINK FENCING AND GATES PART 1 GENERAL 1.01 SCOPE OF WORK A. The Contractor shall furnish and install all materials, labor, equipment and incidentals required to provide chain link fencing and gates as Shown on the Contract Drawings

More information

Section 808. FENCING

Section 808. FENCING 808.01 Section 808. FENCING 808.01. Description. This work consists of providing and erecting, or moving existing, woven wire fence, temporary fence, protective fence, chain link fence, high-tensile wire

More information

SECTION CHAIN LINK FENCE GALVANZED CHAIN LINK FABRIC ON GALVANIZED FRAMEWORK [Provided by Master Halco]

SECTION CHAIN LINK FENCE GALVANZED CHAIN LINK FABRIC ON GALVANIZED FRAMEWORK [Provided by Master Halco] SECTION 32 31 13 CHAIN LINK FENCE GALVANZED CHAIN LINK FABRIC ON GALVANIZED FRAMEWORK [Provided by Master Halco] PART 1 GENERAL 1.01 SECTION INCLUDES A. Galvanized (zinc) coated chain link fabric with

More information

CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST

CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST CITY OF PITTSBURG ENGINEERING DEPARTMENT CONTRACT NO. 2012-16A WATER TREATEMENT PLANT CAPITAL IMPROVEMENTS PHASE 1A ADDENDUM #1 FENCE AND DITCH AUGUST 2014 CHAIN LINK FENCE SPECIFICATIONS Chain link fence,

More information

APPENDIX FENCE GENERAL NOTES

APPENDIX FENCE GENERAL NOTES APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.

More information

1. Layout. Step 1. Step 2. Step 3. Fig. 1

1. Layout. Step 1. Step 2. Step 3. Fig. 1 1-3/8 Panel Clamp Tools You Will Need: Tape Measure, Mason s String, Stakes, Hole Digger, Shovel, Level, Wheelbarrow, Wrenches or Adjustable Wrench, Hacksaw, Pliers, Cutting Pliers, Fence Stretcher and

More information

Baseball Backstopper System

Baseball Backstopper System D 8 7 6 5 4 3 2 1 Baseball Backstopper System Cable Design - 4 Poles Layout Form Project Name: Zip Code: A2/A1 = D C B1/A2 = B2/A1 = C A2 POLE A1 POLE B A2/B2 = B1/A1 = B B2 POLE B1 POLE A Please fill

More information

SECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).

SECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM). PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3

More information

INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE

INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE INSTALLATION INSTRUCTIONS CHAIN-LINK FENCE AND GATE 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally established property lines. If uncertain, refer to real estate

More information

SECTION BULLET- RESISTANT DOORS

SECTION BULLET- RESISTANT DOORS 1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and

More information

COMPONENTS INSTALLATION

COMPONENTS INSTALLATION PIPE BRACE ASSEMBLY - 8' FIXED-KNOT FENCE Brace posts... 14'x 2 7/8" Structural Tubing Cross Members... 10'x 2 3/8 Structural Tubing Angle Brace... 12'x 2 3/8 Structural Tubing Angle Brace Foot... 6' x

More information

SECTION 19: Endwood Fusion Welded Gate Installation Guide

SECTION 19: Endwood Fusion Welded Gate Installation Guide SECTION 19: Endwood Fusion Welded Gate Installation Guide ASSEMBLY AND INSTALLATION FOR: Fusion Welded Gates Gate Frame with Full Size Pickets Privacy & Board on Board California & Shadowbox Gate width

More information

SECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS

SECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division

More information

DENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION METAL LOCKERS

DENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION METAL LOCKERS PART 0 A/E INSTRUCTIONS 0.01 GENERAL DESIGN REQUIREMENTS A. Architect shall coordinate with the DPS Project Manager the type, layout and size of lockers required on the project. B. Varsity athletic Lockers

More information

CHAIN LINK FENCING DOCUMENT NUMBER: APPLICATION: ELEMENTARY, MIDDLE AND HIGH SCHOOL

CHAIN LINK FENCING DOCUMENT NUMBER: APPLICATION: ELEMENTARY, MIDDLE AND HIGH SCHOOL CHAIN LINK FENCING DOCUMENT NUMBER: 02800 APPLICATION: ELEMENTARY, MIDDLE AND HIGH SCHOOL DATE OF ISSUE: 06-02-98 - miscellaneous revisions 08-06-97 - miscellaneous clarifications 06-02-97 - miscellaneous

More information

SECTION METAL FABRICATIONS

SECTION METAL FABRICATIONS SECTION 05100 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes specifications for metal fabrications, including minimum requirements for fabricator, and galvanizing. 1.02 REFERENCE STANDARDS A. ASTM

More information

LEBANON BOARD OF EDUCATION, LEBANON, CONNECTICUT REQUEST FOR PROPOSALS FOR LYMAN MEMORIAL HIGH SCHOOL BOYS LOCKER ROOM 2/24/2017

LEBANON BOARD OF EDUCATION, LEBANON, CONNECTICUT REQUEST FOR PROPOSALS FOR LYMAN MEMORIAL HIGH SCHOOL BOYS LOCKER ROOM 2/24/2017 LEBANON BOARD OF EDUCATION, LEBANON, CONNECTICUT REQUEST FOR PROPOSALS FOR LYMAN MEMORIAL HIGH SCHOOL BOYS LOCKER ROOM 2/24/2017 The Lebanon Board of Education invites sealed proposals for replacement

More information

5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.

5/16 Flange nut. Bolt Keeper Plate (8 Sq. SYS.) (3) 1/2 x 3 Hex head connector zinc plated bolt w/ washers and nut. Anchor 3 sq. 7 Ga. 2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc

More information

1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.

1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"

More information

SW Region Asset Specifications: Four Strand Barbed Wire Fence Specifications

SW Region Asset Specifications: Four Strand Barbed Wire Fence Specifications Lands Division Sustainable Resource Development SW Region Asset Specifications: Four Strand Barbed Wire Fence Specifications Prior to commencement of construction, contact must be made with the following

More information

6a. Eight Steps to Chain-Link Fence Installation

6a. Eight Steps to Chain-Link Fence Installation 6a. Eight Steps to Chain-Link Fence Installation Before You Start You will need the following tools to install your chain-link fence: Post hole digger Wheelbarrow, shovel and hoe for mixing concrete Tape

More information

Design and Construction Standards SECTION ATHLETIC LOCKERS

Design and Construction Standards SECTION ATHLETIC LOCKERS SECTION 10505 ATHLETIC LOCKERS PART 1 GENERAL 1.1 RELATED DOCUMENTS A. The provisions of the General Conditions, Supplementary Conditions, and the Sections included under Division 1, General Requirements,

More information

AMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS

AMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS A. Drawings and General Provisions of Contract, including General and Supplementary Conditions and

More information

Installation Instructions. Tools Needed. Tape measure. Level. Shovel or Post hole digger. Concrete. Drill. Stakes. Mallet or hammer.

Installation Instructions. Tools Needed. Tape measure. Level. Shovel or Post hole digger. Concrete. Drill. Stakes. Mallet or hammer. Installation Guide EcoStone Fence 1330 West 400 North Orem, UT 84057 Toll Free 1.866.648.9336 Tel. 1.801.655.5236 Fax 1.801.655.5240 www.ecostonefence.com Installation Instructions Introduction. These

More information

ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES WIRE MESH PARTITION FOLDING GATE

ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES WIRE MESH PARTITION FOLDING GATE acorn WIRE ACORNWIRE.COM MESH PARTITIONS DIVISION 10 - SPECIALTIES 10 22 13 WIRE MESH PARTITION 10 22 16 FOLDING GATE GUIDE Page 4 / 5 No. 130A All wire type for normal industrial use. 7, 8, 9, 10 and

More information

FENCE INSTALLATION GUIDE 6 HIGH FENCE

FENCE INSTALLATION GUIDE 6 HIGH FENCE FENCE INSTALLATION GUIDE 6 HIGH FENCE 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative

More information

C. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.

C. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available. SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.

.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation

More information

Congratulations! Your dog is going to love you!

Congratulations! Your dog is going to love you! DIY INSTRUCTIONS Congratulations! Your dog is going to love you! Thank you for ordering your non-electric dog fence kit from Pet Playgrounds. In less than a day you will have your very own personal dog

More information

CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High

CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS Fence Installation Guide 3', 4' & 6' High INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers

More information

Constructing Wire Fences

Constructing Wire Fences 1 of 6 12/3/2010 9:48 AM University of Missouri Extension G1192, Reviewed October 1993 Constructing Wire Fences Richard E. Phillips Department of Agricultural Engineering This guide will provide some basic

More information

SECTION TRAFFIC SIGNAGE

SECTION TRAFFIC SIGNAGE SECTION 10 14 53 TRAFFIC SIGNAGE PART 1 - GENERAL 1.01 SECTION INCLUDES A. Furnishing and installing roadside traffic signage. B. Providing additional traffic signs as required in Sections 01 55 28 Controlling

More information

SCI-FAB Product Specifications. Casework Section 1. Part 1 General

SCI-FAB Product Specifications. Casework Section 1. Part 1 General SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.

More information

Introduction. Planning

Introduction. Planning Introduction Since fencing is such an important part of a livestock grazing system, the USDA- Natural Resources Conservation Service (NRCS) has developed specific designs and specifications for landowners

More information

For crossing under a railroad, contact the specific railroad company's engineering department.

For crossing under a railroad, contact the specific railroad company's engineering department. PAGE 330524-1 SECTION 330524 SPECIFIER: This section is for the underground installation of piping by directional drilling. When specifying this method of piping installation, care must be taken to ensure

More information

Installing Gates and Posts Tips and Pointers

Installing Gates and Posts Tips and Pointers Installing Gates and Posts Tips and Pointers When one installs a gate we hope that the gate will not sag and that the gate post will not move so that our work will not only look great but function properly.

More information

FENCING PRODUCTS FENCING PRODUCTS. Please call:

FENCING PRODUCTS FENCING PRODUCTS. Please call: YardGard brand of quality Chain Link borders and fencing meet the needs of residential property owners, industry and municipalities. Manufactured and distributed by Midwest Air Technologies, Inc,. F or

More information

NON-ELECTRIC DOG FENCES

NON-ELECTRIC DOG FENCES NON-ELECTRIC DOG FENCES Thank you! Thank you for ordering your non-electric dog fence kit from Pet Playgrounds. In less than a day you will have your very own personal dog park installed on your property.

More information

FENCE INSTALLATION GUIDE 8 HIGH WALLS

FENCE INSTALLATION GUIDE 8 HIGH WALLS FENCE INSTALLATION GUIDE 8 HIGH WALLS 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek decorative

More information

Transmission Line Support Systems

Transmission Line Support Systems Antenna Support Bracket for transmission line The Antenna Support Bracket angle mounts directly to a 4-1/2" (114 mm) OD antenna pipe mount or tower leg. This is ideal for supporting transmission line runs

More information

Midwest Roadside Safety Facility

Midwest Roadside Safety Facility B 64" 1626 602'-8 1/16" 183695 548'-0" 167030 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 373839 40 25 IMPACT 1500A 48" 12 27'-5" 8355 [] 3x7 CL A Galvanized

More information

A. Deviation from this standard must be approved by the Project Architect.

A. Deviation from this standard must be approved by the Project Architect. September 2012, rev. 00 26 5600 Exterior Lighting PART 1. GENERAL 1.01 Related Documents A. Deviation from this standard must be approved by the Project Architect. B. Drawings and general provisions of

More information

SECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section

SECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section 02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,

More information

SPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS

SPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS SPECIFICATIONS FOR THE MANUFACTURE AND DESIGN OF PRECAST THREE SIDED ARCH STRUCTURES, WINGWALLS AND HEADWALLS 1. DESCRIPTION THESE SPECIFICATIONS ARE FOR A PRECAST THREE SIDED ARCH STRUCTURE, HEADWALLS

More information

H HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT

H HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.

More information

TENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018

TENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018 SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply

More information

No No No

No No No INSTALLATION, ASSEMBLY & MAINTENANCE MANUAL BASEBALL BACKSTOP No. 331025 No. 331036 No. 331039 No. 331025 No. 331036 No. 331039 INSTALLER NOTE: Upon completion of the installation/assembly of this baseball

More information

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details. SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.

More information

HOW TO BUILD A DEER OR ELK-PROOF FENCE. Saskatchewan Environment Resource Stewardship Branch 112 Research Drive Saskatoon, Saskatchewan S7K 2H6

HOW TO BUILD A DEER OR ELK-PROOF FENCE. Saskatchewan Environment Resource Stewardship Branch 112 Research Drive Saskatoon, Saskatchewan S7K 2H6 HOW TO BUILD A DEER OR ELK-PROOF FENCE Saskatchewan Environment Resource Stewardship Branch 112 Research Drive Saskatoon, Saskatchewan S7K 2H6 Revised March 2005 1 This information is intended to assist

More information

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details. SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.

More information

b. B aluminum and aluminum-alloy extruded bar, rod, wire, shape and tube

b. B aluminum and aluminum-alloy extruded bar, rod, wire, shape and tube MODEL 240I SECTION 08120 FLUSH ALUMINUM DOORS AND FRAMES PART I GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals required to deliver and install aluminum doors, frames,

More information

System 3000 specifications

System 3000 specifications System 3000 specifications Scope: Materials: Type of Bookstack: This specification covers delivery and installation of steel library shelving of the bracket type. Height, depth and accessories shall be

More information

SECTION SWINGING AUTOMATIC ENTRANCES IN-GROUND, AUTOMATIC SWING DOOR OPERATOR CONVERTER ADAPTED TO BROOKFIELD NB-500 EXTREME DUTY OPERATOR

SECTION SWINGING AUTOMATIC ENTRANCES IN-GROUND, AUTOMATIC SWING DOOR OPERATOR CONVERTER ADAPTED TO BROOKFIELD NB-500 EXTREME DUTY OPERATOR SECTION 084229.33 SWINGING AUTOMATIC ENTRANCES IN-GROUND, AUTOMATIC SWING DOOR OPERATOR CONVERTER ADAPTED TO BROOKFIELD NB-500 EXTREME DUTY OPERATOR PART 1-GENERAL 1.01 DESCRIPTION A. This section describes

More information

SECTION FOLDING GLASS PANEL PARTITIONS

SECTION FOLDING GLASS PANEL PARTITIONS SECTION 10 22 26.35 FOLDING GLASS PANEL PARTITIONS USE THIS SECTION WHEN SPECIFYING OVERHEAD SUPPORTED FOLDING GLASS PANEL PARTITIONS. SECTION INCLUDES OVERHEAD TRACK ASSEMBLY, MOUNTING BRACKETS, MOUNTING

More information

EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL

EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION 05720 METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING is a high quality steel fencing system comprised of a hybrid

More information

SECTION (10670) - WIRE CLOSET AND UTILITY SHELVING

SECTION (10670) - WIRE CLOSET AND UTILITY SHELVING SECTION 10 57 23.13 (10670) - WIRE CLOSET AND UTILITY SHELVING PART 1 GENERAL 1.01 SUMMARY 1. Wire Closet Shelves B. Related Sections: 1.02 SUBMITTALS 1. Section 06 10 00 (06100) - Rough Carpentry A. Submit

More information

designmasterfence.com

designmasterfence.com designmasterfence.com > INDEX > WHAT IS DESIGNMASTER? > PRODUCTS APPLICATIONS 2 3 > CLASSIC FENCE PANEL Specs & Advantages > CLASSIC FENCE POST Specs, Advantages & Installation > BRACKETS & ACCESSORIES

More information

UNIVERSAL PANEL AND GATE

UNIVERSAL PANEL AND GATE PVC Fencing / Residential Style UNIVERSAL PANEL AND GATE INSTALLATION INSTRUCTIONS Fencing Without Boundaries TM 1 BEFORE YOU START, IT S IMPORTANT TO CHECK......That fence footings do not exceed legally

More information

Standard Specification for Fence Fittings 1

Standard Specification for Fence Fittings 1 Designation: F 626 08 Standard Specification for Fence Fittings 1 This standard is issued under the fixed designation F 626; the number immediately following the designation indicates the year of original

More information

ROOFING City of Grand Rapids Building Safety Division

ROOFING City of Grand Rapids Building Safety Division ROOFING City of Grand Rapids Building Safety Division 218-326-7601 www.cityofgrandrapidsmn.com This handout is intended only as a guide and is based in part on the 2015 Minnesota State Building Code, Grand

More information

SECTION TRACER WIRE FOR NONMETALLIC PIPE

SECTION TRACER WIRE FOR NONMETALLIC PIPE PART 1 GENERAL 1.1 DESCRIPTION A. The CONTRACTOR shall furnish and install a conductive tracer wire with all buried plastic water mains, services and appurtenances in accordance with the Water Utilities

More information

BRACE ASSEMBLIES FOR WIRE FENCES. What They Are - How They Work - How To Construct Them

BRACE ASSEMBLIES FOR WIRE FENCES. What They Are - How They Work - How To Construct Them Fencing Order No. 307.220-1 Agdex: 724 March 1996 BRACE ASSEMBLIES FOR WIRE FENCES What They Are - How They Work - How To Construct Them When constructing wire fences, brace assemblies are required to

More information

Exclusive Cantilever Gates

Exclusive Cantilever Gates Exclusive Cantilever Gates Chainlink Gates Aluminum Cantilever Gates Single Track Box Frame Components & Hardware Upper Track Lower Track Z4 Truck Assembly Z8 Truck Assembly All Gates Feature Enclosed

More information

INSTALLATION MANUAL. 2. Check with local utility companies for locations of underground cables or pipe lines.

INSTALLATION MANUAL. 2. Check with local utility companies for locations of underground cables or pipe lines. INSTALLATION MANUAL Install our maintenance free fencing system yourself! About 90% of our residential clientele install our fencing systems themselves. Why hire and pay someone to install it when you

More information

(50 FT FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" 8-0" 6-0" Truss Depth. 3" sheets 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.

(50 FT FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0 7-6 8-0 6-0 Truss Depth. 3 sheets 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T. Column truss connection (See details sheets 3 & 4 of 10) \ Span (Odd number of panels) \ Span (Even number of panels) Back truss chord Top truss chord \ Truss Chord splice Truss depth (See details \ Left

More information

LOCKER SPECIFIERS GUIDE. The standard of excellence for business, industry and institutions. Lockers Cabinets Shelving

LOCKER SPECIFIERS GUIDE. The standard of excellence for business, industry and institutions. Lockers Cabinets Shelving LOCKER SPECIFIERS GUIDE Lockers Cabinets Shelving The standard of excellence for business, industry and institutions FINISH GUIDE NANO METAL ROLLER LATCHING SYSTEM For unmatched security, nano metal roller

More information

Raceline / Shockline/Endloop Installation Manual

Raceline / Shockline/Endloop Installation Manual Raceline / Shockline/Endloop Installation Manual Scan this QR code to watch the Installation Video. Trouble Shooting Hotline -800-878-5644 Flex Fence Raceline/Shockline Fence Installation Guide Before

More information

SECTION 58 PRECAST CONCRETE BOX CULVERT. This work consists of furnishing and installing Pre-cast Concrete Box Culverts.

SECTION 58 PRECAST CONCRETE BOX CULVERT. This work consists of furnishing and installing Pre-cast Concrete Box Culverts. SECTION 58 PRECAST CONCRETE BOX CULVERT 58.1 DESCRIPTION A. General This work consists of furnishing and installing Pre-cast Concrete Box Culverts. B. Related Work Section 51 Section 52 Section 53 Section

More information

SECTION STRUCTURAL STEEL. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.

SECTION STRUCTURAL STEEL. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. SECTION 051200 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting

More information

INSTALLATION MANUAL. 2. Check with local utility companies for locations of underground cables or pipe lines.

INSTALLATION MANUAL. 2. Check with local utility companies for locations of underground cables or pipe lines. INSTALLATION MANUAL Install our maintenance free fencing system yourself! About 90% of our residential clientele install our fencing systems themselves. Why hire and pay someone to install it when you

More information

1.1 RELATED DOCUMENTS

1.1 RELATED DOCUMENTS SECTION 050505 -BEVEL RAIL ENDS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including General and Supplementary Conditions and Division 01 Specification Sections

More information

SE Region Asset Specifications Four Strand Barbed Wire Fence Specifications

SE Region Asset Specifications Four Strand Barbed Wire Fence Specifications Lands Division Sustainable Resource Development SE Region Asset Specifications Four Strand Barbed Wire Fence Specifications 1. Project Materials The contractor is to supply all the labour, tools and equipment

More information

RR-F-191/1D 14 May SUPERCEDING RR-F-191/1C July 22, 1981 FEDERAL SPECIFICATION SHEET

RR-F-191/1D 14 May SUPERCEDING RR-F-191/1C July 22, 1981 FEDERAL SPECIFICATION SHEET 14 May 1990 ----------- SUPERCEDING RR-F-191/1C July 22, 1981 FEDERAL SPECIFICATION SHEET FENCING, WIRE AND POST METAL (CHAIN-LINK FENCE FABRIC) (DETAIL SPECIFICATION) This Federal Specification is approved

More information

SECTION THERAPEUTIC POOL ACCESSORIES

SECTION THERAPEUTIC POOL ACCESSORIES PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 13 17 23.11 THERAPEUTIC POOL ACCESSORIES SPEC WRITER NOTES: Delete between // // if not applicable to project. Also, delete any other item or paragraph not applicable

More information

6o ft (18.3 m) Southwest Windpower, Inc West Route 66 Flagstaff, Arizona USA Phone: Fax:

6o ft (18.3 m) Southwest Windpower, Inc West Route 66 Flagstaff, Arizona USA Phone: Fax: 6o ft (18.3 m) sectional MONOPOLE TOWER INSTALLATION MANUAL Southwest Windpower, Inc. 1801 West Route 66 Flagstaff, Arizona 86001 USA Phone: 928.779.9463 Fax: 928.779.1485 www.skystreamenergy.com 3-CMLT-1390-01

More information

DOCUMENT ADDENDUM NO. 4. Issued to all Bidders: Date: October 14, Contract Name: Electrical Installation. Contract Number: C8410

DOCUMENT ADDENDUM NO. 4. Issued to all Bidders: Date: October 14, Contract Name: Electrical Installation. Contract Number: C8410 DOCUMENT 009104 - ADDENDUM NO. 4 Issued to all Bidders: Date: October 14, 2015 Contract Name: Electrical Installation Contract Number: C8410 This addendum forms a part of the Bid described above. The original

More information

SECTION PRECAST CONCRETE STRUCTURES

SECTION PRECAST CONCRETE STRUCTURES SECTION 02605 PRECAST CONCRETE STRUCTURES PART 1 GENERAL 1.01 DESCRIPTION A. CONTRACTOR shall provide all professional services, labor, materials, equipment and incidentals as shown, specified and required

More information

SIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0", 8'-0", 10'-0" NOMINAL SPREAD

SIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0, 8'-0, 10'-0 NOMINAL SPREAD Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"

More information

GLOSSARY OF TERMS SECTION 8

GLOSSARY OF TERMS SECTION 8 GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the

More information

Down Stage Right -Theatrical and Entertainment Rigging Supplies

Down Stage Right -Theatrical and Entertainment Rigging Supplies Shackle Plates There are five uniquely different designs in the Shackle Plates Dynasty. Each one allows you the freedom of choice as you design the rigging requirements of your scenery, as well as meeting

More information

INS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)...

INS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)... INS-88.500-0A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Unpacking the KSCR... 2 2. Splicing the KSCR (If Required)... 4 3. Assemble Curb and Rail Corners... 5 4. Install Cross Bracing (If Required)...

More information

SECTION HOLLOW METAL DOORS AND FRAMES

SECTION HOLLOW METAL DOORS AND FRAMES SECTION 081113 HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: Include construction details, material

More information

Directions for the 25' Jr Batting Cage & Frame

Directions for the 25' Jr Batting Cage & Frame Directions for the 25' Jr Batting Cage & Frame Parts Qty Part Description 1 6 Upper corners of the arch (with hex bolts) 2 6 Bent pipe for arch feet 3 6 Pipe with no swedge (2 per horizontal arch) 4 12

More information

Lateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later

Lateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later Lateral Support Decks over 24 above grade require lateral support* *Exceptions to be discussed later Decking Types of Decking: -2x4s & 2x6s -five quarter span rated decking boards -Wood plastic composite

More information

Annie Tel: MSN: All chain-link fences aren't the same

Annie Tel: MSN: All chain-link fences aren't the same Attractive, versatile and creative - a chain-link fence system can be an excellent choice. With the right fence you can expect years of protection, privacy and value. But as with any investment, it pays

More information

FENCE INSTALLATION GUIDE 3, 4, & 6 HIGH FENCE

FENCE INSTALLATION GUIDE 3, 4, & 6 HIGH FENCE FENCE INSTALLATION GUIDE 3, 4, & 6 HIGH FENCE 1.866.648.9336 www.simtekfence.com INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers of SimTek

More information

SECTION ROOF ACCESSORIES. Display hidden notes to specifier. (Don't know how? Click Here)

SECTION ROOF ACCESSORIES. Display hidden notes to specifier. (Don't know how? Click Here) SECTION 07720 ROOF ACCESSORIES PART 1 GENERAL 1.1 SECTION INCLUDES Display hidden notes to specifier. (Don't know how? Click Here) A. Attachment clamp system for standing seam metal roofs. B. Attachment

More information

MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C

MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C MEDIUM DUTY CAST IRON SLIDE GATES SERIES 20-10C Revised October 2007 Armtec reserves the right to alter designs. General The Armtec Sluice Gate is a quality and highly economical gate for a variety of

More information

SECTION (10670) - WIRE CLOSET AND UTILITY SHELVING

SECTION (10670) - WIRE CLOSET AND UTILITY SHELVING SECTION 10 57 23.13 (10670) - WIRE CLOSET AND UTILITY SHELVING PART 1 GENERAL 1.01 SUMMARY 1. Wire Closet Shelves B. Related Sections: 1. Section 06 10 00 (06100) - Rough Carpentry 1.02 QUALITY ASSURANCE

More information

1. ANSI/ASME Standard B , Square and Hex Bolts and Screws, Inch Series

1. ANSI/ASME Standard B , Square and Hex Bolts and Screws, Inch Series SECTION 31 66 13 HELICAL PILES AND HELICAL ANCHORS PART 1 - GENERAL 1.1 DESCRIPTION A. This work pertains to furnishing and installing Helical Piles and Bracket Assemblies shown in the Contract in accordance

More information

SIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) POLE CAP

SIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0, 8'-0, 10'-0 NOMINAL SPREAD (SEE CONTRACT) POLE CAP Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"

More information

High-Tensile Coated Wire Fence Installation Guide

High-Tensile Coated Wire Fence Installation Guide High-Tensile Coated Wire Fence Installation Guide Please follow directions for a long lasting installation that will not sag after tension is applied to the rails. Proper bracing of corner and end posts

More information

SECTION R507 DECKS DECKING LEDGER BOARD BEAM. FOOTING BEAM SPAN CANTILEVER For SI: 1 inch = 25.4 mm FIGURE R507.2 DECK CONSTRUCTION

SECTION R507 DECKS DECKING LEDGER BOARD BEAM. FOOTING BEAM SPAN CANTILEVER For SI: 1 inch = 25.4 mm FIGURE R507.2 DECK CONSTRUCTION SECTION R507 DECKS R507.1 Application. The provisions of this section shall provide prescriptive requirements for the design and construction of all uncovered, wood-framed, single-span exterior decks.

More information