Infinity. Surface Mounted Headwall. Installation Instructions. The.
|
|
- Britney Nash
- 5 years ago
- Views:
Transcription
1 The Infinity Surface Mounted Headwall Installation Instructions Tel: Fax: Hospital Systems Inc. 750 Garcia Avenue Pittsburg CA USA Introduction: The Hospital Systems, Inc. Infinity Surface Mounted Patient Headwall is made to order for this project. Each headwall consists of a rough-in box or Service Chase and the pre-wired and pre-piped headwall that is particular to each location or type. Before attempting to install, please read and understand all of the instructions. In particular please refer to the final approved submittal drawings as they will take precedence over these instructions. Document INSI-1
2 1. Install backing in building wall as required. Set ceiling mounting plate for the vertical chase [if so specified]. 2. Set and level service chase module [if so equipped] and secure it to the building wall. 3. Locate stud center or backing material. Layout the rail hanger bracket for the top-most rail at the height above the finished floor as noted on elevation drawings, then but the hanger bracket against the service chase. Align and level the hanger bracket and secure to wall using appropriate mounting hardware [wood screws, toggle bolts, sheet metal screws, etc as per local code, Note: Hardware is not supplied with headwall]. Note. Hanger bracket must be straight and level. If the wall is not true, shim the hanger bracket as needed. Repeat the above for the middle and lower Infinity rails. Note: Not all systems are equipped with all three rails. Refer to elevation drawings for each headwall installation. 4. To install the horizontal rails, begin with the top rail and work down. Remove the top cap and set it aside. If connecting a vertical chase or additional rail, remove the ¼-20 nut and washer from the connecting stud. Set the horizontal rail onto the hanger bracket, [if connecting with the chase, feed the flex conduit containing the service conductors into the chase module]. Note: The flex conduit and conductors have been cut and laced for proper fit. No field cutting of either is required. Butt the horizontal rail against the service chase module, align, and reinstall the ¼-20 connecting studs. Note: Be sure to attach the ground wire from the chase to the rail. Secure the rail to the building wall/backing material using appropriate hardware [see Step 3 above] 5. Repeat Step 4 for the remaining horizontal sections. Caution: Be extremely careful when installing the horizontal rail containing the medical gas piping. Note: If the units you are installing are composed of several horizontal sections per rail, you must install the section closest to the service chase first. Proceed with the adjacent section only after securing the first section to the wall and chase. Slide the sections snugly together, align and install connecting studs for each section as you go, again securing each section to the wall before proceeding. 6. Connect the marked conductor color to color at the terminal blocks, or use wire nuts in the junction boxes. All conductors have been marked and laced for proper fit. All interconnecting wiring in the service chase is factory installed. Feed the nurse call and other low voltage system wires or pull cords into their respective terminal compartments for future connection by others. Medical gas piping has been factory cut to exact fit and tied into the service chase for field connection at the top of the chase and at the intersection of the vertical chase and the horizontal rail. Note: If the horizontal rails are in several sections, connections will be required between sections as well. Fitting are provided. 7. With all sections completed, replace the top cap on the horizontal rails. If an overbed lighting fixture is included, install it after the top cap has been re-installed. Re-install the access panels on the vertical service chase. 8. If equipped with Unimount Track and Eclipse Equipment Rail between center and lower rails [or below center rail], secure the Unimount Track to the backing material using appropriate hardware. Attach the stand-off brackets to the Unimount Track, then install the Eclipse Equipment Rail in the stand-off and tighten the set screw. Installation Instructions for the Infinity Surface Mounted Headwall [Doc INSI-1] Page 2 of 8
3 Installation Instructions for the Infinity [Doc INSI-1] Page 3 of 8
4 Installation Instructions for the Infinity [Doc INSI-1] Page 4 of 8
5 Electrical Hookup from Chase Installation Instructions for the Infinity [Doc INSI-1] Page 5 of 8
6 Medical Gas Piping Feeds from Chase Installation Instructions for the Infinity [Doc INSI-1] Page 6 of 8
7 Backbox Arrangement for Infinity Rail without Chase Electrical and Communications are fed from individual sections of the backbox into the appropriate raceway within the Infinity Installation Instructions for the Infinity [Doc INSI-1] Page 7 of 8
8 Medical Gas Connections for Infinity without Chase Installation Instructions for the Infinity [Doc INSI-1] Page 8 of 8
PCS. Patient Security Service Console. Installation Instructions.
www.hsiheadwals.com PCS Patient Security Service Console Installation Instructions Tel: 925.427.7800 Fax: 925.427.0800 support@hsiheadwalls.com Hospital Systems Inc. 750 Garcia Avenue Pittsburg CA 94565
More informationInstallation Instructions
Please read through these instructions completely prior to attempting any installation www.hsiheadwalls.com Installation Instructions Installation Instructions Tel: 925.427.7800 Fax: 925.427.0800 support@hsiheadwalls.com
More informationHO4 Surface Mount Installation Instructions Overview
Overview Step 4 Mounting to Structure Pages 5-6 Step 5 Joining Luminaires Pages 7-8 Step 1 Mounting Types & Locations Page 2 Step 6 Closing Luminaires Page 9 Helpful Video 0-10V Dimming Step 2 Identification
More informationSmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide
SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide WMK-034 This display kit mounts ViewSonic 46 Video Wall displays in a 3 wide by 3 deep landscape configuration. The frame
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More information5 ACCESS PANEL INSTALLATION SPACER *SLIDE TO LOCATION OF FASTENER DURING INSTALLATION OF EACH FASTENER
1/2 K.O. (3/8 K.O. on 165 with factory supplied 3/8 flex conduit fitting) TR - Trim Flange Side Blocking Install Method Secure fixture to structure following instructions below: 1. Remove lens and internal
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More information3 wide x 3 deep Video Wall Display Installation Guide
HoverTrack Series 3 wide x 3 deep Video Wall Display Installation Guide VWD-3X3-X462 This display kit mounts NEC X461UN and X462UNS LCD monitors in a 3 wide by 3 deep landscape configuration. The frame
More informationAdjustable Countertop Installation
Adjustable Countertop Installation Applies to Models: A1, A2, A3, A4, A5, & A6 Required Tools: Stud Finder, Level 1/4 deep well socket, Screwdrivers, Tape Measure, Drill and Drill Bits Language of origin:
More informationAssembly Instructions for model: VMPR1
Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design
More informationOpus Cabinets with "H Storage Unit, continued
66 Health Volume 2 Casegoods Specification Guide Fascia is used to extend cabinets to the ceiling Fascia can only be used on 84"H cabinets Fascia accommodates ceiling heights of 7'6" 9'6" in 1 16" increments
More informationCompass Patient Headwall. Installation Guidelines. Prior to installation, please carefully read and familiarize yourself with all of the Guidelines
Compass Patient Headwall Installation Guidelines 750 Garcia Ave Pittsburg CA 94565 USA Tel: +1.925.427.7800 Fax: +1.925.427.0800 These installation guidelines describe how to install the Compass Patient
More informationTriple Bypass System
Triple Bypass System ASSEMBLY INSTRUCTIONS TRIPLE BYPASS SYSTEM Recommended Tools Drill with 1/4 Drill Bit and Phillips Screw Bit 7/16 Combination Wrench Socket Wrench with 7/16 and 9/16 Socket Level Tape
More informationContour Hanger ASSEMBLY INSTRUCTIONS
Contour Hanger ASSEMBLY INSTRUCTIONS CONTOUR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationIndustrial Hanger ASSEMBLY INSTRUCTIONS
Industrial Hanger ASSEMBLY INSTRUCTIONS INDUSTRIAL HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationTWIG Hanger ASSEMBLY INSTRUCTIONS
TWIG Hanger ASSEMBLY INSTRUCTIONS TWIG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench
More informationHP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions Overview
Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires proper support as each luminaire is being installed. DO
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationLIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION
CAUTION: BEFORE BEGINNING INSTALLATION REVIEW LAYOUT DRAWINGS, AND SHIPMENT. MAKE SURE ALL LIGHT S AND MATERIALS ARE ON SITE AND READILY ACCESSIBLE. IF ANY ICON MATERIALS ARE MISSING, CONTACT ICON INTERNATIONAL
More informationHP-2 / HP-4 / HP-6 Ceiling to Wall Inside Corner Installation Instructions Overview
Overview Step 4 Mounting to Structure Page 6 Step 1 Mounting Locations & Rough-Ins Pages 2-3 Step 2 Identification & Preparation Page 4 Step 6 Securing Corner Joints Page 8 Step 3 Opening Luminaires Page
More informationAssembly Instructions for Model: VMPR1
Assembly Instructions for Model: VMPR1 Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LC/LP
More informationPillar Hanger ASSEMBLY INSTRUCTIONS
Pillar Hanger ASSEMBLY INSTRUCTIONS PILLAR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationC70 Window Roller Repair Taken from: Heres the problem:
C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER R H
INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER 10.6.2016 PARTS INSTALLATION SPECIFICATIONS AND TOOLS INSTRUCTIONS 2-1/4" 2-7/8 11-3/8" 1/4" 2-1/8 PARTS INSTALLATION AND INSTRUCTIONS TOOLS
More informationROCKWELL 4-IN-1 DOOR. Two Panel Door. Half X Door. Z Combination Door. Double X Door
ROCKWE 4-IN-1 DOOR Two Panel Door Half X Door Double X Door Z Combination Door Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationSAVE THESE INSTALLATION INSTRUCTIONS
Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT 7500003 8/4 Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT GENERAL INSTALLATION WARNING To Reduce Risk Of Death,
More informationSpoked GARRICK HANGER
Spoked GARRICK HANGER ASSEMBLY INSTRUCTIONS SPOKED GARRICK HANGER Recommended Tools Drill with 1/8 and 1/4 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench
More informationINSTALLATION INSTRUCTIONS
www.marwincompany.com Kit Number Door Height Rough Opening Height KD200BB68 80 84 ½ KD200BB70 84 88 ½ KD200BB80 96 100 ½ INSTALLATION INSTRUCTIONS 200BB SERIES KD POCKET DOOR FRAME FOR 2 X 4 STUD WALLS
More informationColor Stories Studio Installation Instructions
Tools Required 1 - Stud Finder 8 - Carpet Sliders 1 - Level 1 - Phillips Screwdriver 1 - Flathead Screwdriver 1 - Power Drill with 3/16 Bit 1 - Package of Shims 2-8 Ft. Step Ladder Components V (2) Wall
More informationStag Hanger ASSEMBLY INSTRUCTIONS
Stag Hanger ASSEMBLY INSTRUCTIONS STAG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench
More informationInstallation Guide. Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationPlayground Assembly Instructions
Before You Begin Playground Assembly Instructions Locate the playground set on firm, level ground. Assemble the playground on or close to its permanent location Two people are recommended to assemble the
More informationWAREHOUSE HANGER INSTALLATION INSTRUCTIONS R H INS T A L L A TIO N INS T R U C TIO N S
INS T A L L A TIO N INS T R U C TIO N S WAREHOUSE HANGER NOTE: Due to the size and weight of the Warehouse Hanger it is recommended that this Hanger be installed on 3 4 or wider doors. 10.11.2016 2-3/16"
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER R H
INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER 10.5.2016 2-1- 3/16" 11/16" 8" 8 O 2-7/8 Ø2-7/8" 3-1/2 3-1/2" 12-9/16 12-9/16" PLEASE NOTE: These instructions are specific to a particular
More informationInstallation Instructions for TruLine 1A Center Feed Power Channel Connector
IMPORTANT INFORMATION - This instruction must be used concurrently with other TruLine A BIY installation instructions. - This product is wall or ceiling mount. - This instruction shows a typical installation.
More informationROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door
ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are
More informationTOYOTA TUNDRA CARGO DIVIDER Preparation. Part Number: PT
Preparation Part Number: PT767-34070 Kit Contents 1 1 Divider Screen 2 1 LH Bracket with Warning Label 3 1 RH Bracket without Warning Label NOTE: Part number of this accessory may not be the same as the
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationCellar Hanger ASSEMBLY INSTRUCTIONS
Cellar Hanger ASSEMBLY INSTRUCTIONS CELLAR HANGER Recommended Tools Drill with 1/8 and 1/4 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16, 7/16, and 5/8 Combination Wrench Socket
More informationHP-2 / HP-4 Wall Wash Recessed T-Bar Installation Instructions Overview
HP-2 / HP-4 Wash Recessed T-Bar Installation Instructions Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires
More informationEXPLODED VIEW AND PART CALL OUT ASSEMBLING THE METALUX DF SERIES FRAME KIT
EXPLODED VIEW AND PART CALL OUT CUTOUT DIMENSIONS ON PAGE 2 CEILING BRACING (BY OTHERS) SHEET ROCK METALUX DF SERIES FRAME KIT S282 (2'X2') FIXTURE SHOWN FIXTURE SIZE FRAME KIT PART # 2' X 2' DF-22W-U
More informationRockwell 4-in-1 Sliding Door
Rockwell 4-in-1 Sliding Door ASSEMBLY INSTRUCTIONS ROCKWELL 4-IN-1 SLIDING DOOR Recommended Tools Drill with Phillips Bit Socket Wrench with 7/16 Socket Rubber Mallet Adjustable Square ROCKWELL 4-IN-1
More information43107 Rhino Jerry Can Holder Rhino Jerry Can Holder - Horizontal
Important: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fitment and report any discrepancies. Clean the alloy tray prior to installation.
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationMounting Instructions Item No.: xxx
Mounting Instructions Item No.: 271.92.xxx Wall-Beds 1 General Notes For vertical folding beds Successful and safe installation of Bed-Lift and construction of casework requires a professional skill level
More informationInstruction sheet -- VTI Flat panel TV cart
VTI Manufacturing, Inc. Instruction sheet -- VTI Flat panel TV cart Model number: 10235 Congratulations for having chosen this excellent VTI product. To assure your complete satisfaction, this product
More informationWG-4 Wall Guard Installation Instructions
WG-4 Wall Guard Installation Instructions Architectural Products Division Step 1: Determine top of wall guard and snap a chalk line 1/8 below to locate top of aluminum retainer, see fig 1. Store material
More informationDesk/Wall-Mount Rack
Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware
More informationJ-BOX. 3-O or 4-0 MUD RING J-BOX BRACKET BAR CABLE GRIPPER/ CANOPY MOUNTING STUD 8-32 BRACKET BAR SCREWS CANOPY STRAIN RELIEF POWER CORD CANOPY
KELSEY - CSS Cable Suspended Rotational and Static CSS - Cable Suspended 3-O or 4-0 MUD RING BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS STRAIN RELIEF POWER CORD MOUNTING GRIPPER AIRCRAFT CABLE CABLE
More information31 / 39 / 59 Basin 31 / 39 / 59 Basin Frame Introduction Parts supplied - basin frame
31 / 39 / 59 Basin US-WF0813SCW / US-WF1003SCW / US-WF1503SCW 31 / 39 / 59 Basin Frame US-WF80X81C / US-WF100X81C / US-WF150X81C Installation Instructions Introduction Parts supplied - basin frame All
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationHeavy Duty I-Beam Trolley
Heavy Duty I-Beam Trolley ASSEMBLY INSTRUCTIONS I-BEAM TROLLEY Recommended Tools Level Tape Measure Pencil Drill with 1/8, 1/4, and 3/8, Drill Bits and Phillips Bit Socket Wrench with 9/16 Socket I-BEAM
More informationSubject: P0052 Bed Locator Installation Instructions
Subject: P0052 Bed Locator Installation Instructions Tools required: Standard drill 1/4" diameter drill bit Phillips head screwdriver Screwdriver 5/16" hex nut driver Tape measure 4' (122 cm) level Power
More informationOffice Partitions WARNING. Assembly Instructions. Customer Service A S S E M B LY HARDWARE H1 H2 H3 H4 H5 H8 H9 H10 H11 H12
Customer Service 1-800-645-2986 Assembly Instructions WARNING In order to prevent structural failure, instability, t i p - o v e r, and/or serious injury, please follow i n s t ructions care f u l l y.
More informationINSTALLATION INSTRUCTIONS
TOOLS REQUIRED: Level Square Phillips Screw Driver Slot Screw Driver Pliers Clamp PARTS PROVIDED: Frame Installations Screws. 4 per door. (#8 x 1-3/4 ) Sex Bolt. 4 per frame joint. Torque Lever 2 Shelf
More informationINS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER
INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER 6-1/2" 5" 2-7/16" 3-7/16" Ø2-7/8" 4-7/8" 11" 2" 3/16" 1/2" HORSESHOE W/ BAR S P ECIFICATIONS PARTS AND TOOLS Tools Needed Tape Measure Pencil
More informationEUROLINE CLASSIC SOLID SURFACE Installation Instructions
EUROLINE ASSIC SOLID SURFACE Installation Instructions 12/01/15 EUROLINE ASSIC SOLID SURFACE Installation Instructions Before you begin, please note the following considerations: Safety First! Please use
More informationTop Mount Ultra Modern Hanger
Top Mount Ultra Modern Hanger ASSEMBLY INSTRUCTIONS TOP MOUNT ULTRA MODERN HANGER Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits and Phillips Bit Socket Wrench with 9/16
More informationF-150 Structural Holding System
F-150 Structural Holding System Users Manual December 2013 by Vehicle Service Group. All rights reserved. CO8812.2 502073 Rev. - 12/11/2013 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive
More informationPole Mount Installation Manual
Pole Mount Installation Manual Thank You for Choosing AIMS Power! 1. AIMS Power is a leading supplier of solar products, specializing in PV mounting systems. We ensure our products are manufactured to
More informationRipple Hanger ASSEMBLY INSTRUCTIONS
Ripple Hanger ASSEMBLY INSTRUCTIONS RIPPLE HANGER Recommended Tools Drill with 1/8, 1/4, and 1/2 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationBox Track INSTALLATION INSTRUCTIONS
Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench
More informationSegmented Transfer Plate Installation Instructions
Segmented Transfer Plate Installation Instructions Parts Included in Transfer Plate Kit: Transfer Plate Support Bar (1) Center Segment Right End Segment (1) Left End Segment (1) Mounting Bracket Assemblies
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationBIKE FILE (301)
B IK E F I L E High Efficiency The Bike File is our most space efficient u-lock compatible product. Sturdy sliding hangers allow nine bikes to be securely stored in an eight-foot section while allowing
More informationParts list. Model:10400
Manufacturing, Inc. Instruction sheet -- VTI Flat panel TV cart with cabinet Model number: 10400 Congratulations for having chosen this excellent VTI product. To assure your complete satisfaction, this
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Special-Lite Restroom Partitions IMPORTANT - BEFORE YOU START... 1. Read through these installation instructions first to understand the order of work. 2. Check all components
More informationx2 1/4 (6mm) Floor Anchor
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm
More informationLightline Movable Wall Installation Manual. Preliminary Draft #
Installation Manual Preliminary Draft #3 9-0-3 Table of Contents Parts Identification Tools Aluminum Extrusions Layout Typical Panel Installation Ceiling Channel Ceiling Corner Bracket Hard Floor Securing
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationModel POA-CHB-XL50. Assembly and Installation Manual. Projector Bracket. Contents. Be sure to consult with a qualified installation specialist
Assembly and Installation Manual Projector Bracket Model POA-CHB-XL50 Be sure to consult with a qualified installation specialist This bracket is specifically for use with our projector. Be especially
More informationP /8 Ring Diameter 90. Trim Ring Mounting Holes P /8. 393/16 Ring Diameter. Stud Minimum
PARTS LIST VARIABLE Top Over Head Support Bracket 1 872070 P4000-SMR Over Head Joiner Bracket 1 VARIABLE Bottom Over Head Bracket 1 79741 P4000-SMR 4 Angled Leg 4 100-00230-14 1/4-20 x 31/2 RD. HD. MS.
More informationPrepare the Fixture. Sage 37 Bath. Back Plate Installation (Horizontal) Installation Instructions for 700BCSAGW37_
Installation Instructions for Sage Bath 00BCSAGW_ 90BCSAGEL.0 BATH COLLECTION GENERAL PRODUCT I NFORMATION: This fixture is intended to be installed utilizing NEC compliant junction boxes. This product
More information6 Foot/ 1800mm Aisle Width Net-Contain Aisle Containment for N-Type and S-Type Cabinets
6 Foot/ 1800mm Aisle Width Net-Contain Aisle Containment for N-Type and S-Type Cabinets Panduit Corp. 2016 INSTALLATION INSTRUCTIONS Page 1 of 36 Component Guide for Doors Dual Sliding Containment Door
More informationMANUAL e130. Wallstation
MANUAL 07.29.13 e130 Wallstation The Enovate Medical e130 Wallstation was designed to set a new standard in quality. Enovate Medical s goal is to provide a wallstation that is ready for years of use,
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationGared Pro Portable Backstop
Models: 5016, 5017, & 5018 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units PUBLICATION NO. 551754436 SAVE THESE
More informationINSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System
INSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System IMPORTANT SAFETY INSTRUCTIONS: Read all instructions before installation. Save these instructions for later use.
More informationWARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More informationGeneral Installation Instructions
General Installation Instructions WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Service of the equipment must
More informationPanel & Shelf Identification
4 to 8 Aromatic Cedar Closet Model # 801 1 PLEASE READ INSTALLATION INSTRUCTIONS BEFORE ASSEMBLING Rev. C IF YOU ARE MISSING PARTS OR HAVE QUESTIONS PLEASE CONTACT: customerservice@cedargreen.net Tools
More informationA-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE
A-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE A-dec 574L Dental Light Mounted on an A-dec Inspire TM 59 Central Console Before You Begin. Turn off the power to the system before
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationFD 125 Large-Format Card Cutter
FD 125 Large-Format Card Cutter 3/201 OPERATOR MANUAL Page 2 Table of Contents SAFETY PRECAUTIONS... 4 Introduction... 5 Specifications... 5 Accessories... 5 Major Components and Assemblies... 6 Control
More informationInstallation instructions for oil unit CADDY FURNACE PA03050 and PA03100
Installation instructions for oil unit CADDY FURNACE PA03050 and PA03100 Read these instructions carefully before installing and operating your furnace. Please keep this document! This manual is available
More informationLCD/Plasma Mount Manual
LCD/Plasma Mount Manual Product Overview: Thank you for your Cheetah Mount purchase. All Cheetah Mounts are designed to provide excellent function, high quality, easy installation and stylish appearance.
More informationRegal Series Recessed Flatwalls
Regal Series Recessed Flatwalls General Specifications The Amico Regal Series Recessed Flatwall shall be manufactured by Amico Corporation, in accordance with job specific shop drawings and documents.
More informationPORCH-LOC INSTALLATION INSTRUCTIONS
PORCH-LOC INSTALLATION INSTRUCTIONS 2017 HB&G Building Products, Inc. Porch-Loc Installation Instructions NOTE: DISCARD THE INSTALLATION INSTRUCTIONS AND HARDWARE THAT CAME IN YOUR PERMAPOST PACKAGING
More informationUnit 9. Wall and Ceiling Framing
Unit 9 Wall and Ceiling Framing Wall construction Wall framing includes the assembly of horizontal and vertical members that make up exterior walls and interior partitions. Theses walls support the ceilings
More informationCOMPARE #01-12 OCTOBER 11, Original Vroom. Vroom Garage Ceiling Bracket #9547. Installation. (with L-Brackets) Ease of.
#01-12 OCTOBER 11, 2012 The new Vroom Garage Ceiling Bracket makes it simple to attach Vroom to garage ceiling joists, meaning less installation time is needed. It only takes a third of the time just 30
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SHOWER DOOR KIT ALUMINUM 2503 E. Vernon Avenue, Los Angeles, CA 90058-1826 Phone: (800) 421-6144 EXT. 7740 Fax: (800) 458-7496 crlaurence.com Email: showers@crlaurence.com 11M0260
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More information