Blue Point Engineering

Size: px
Start display at page:

Download "Blue Point Engineering"

Transcription

1 Overview single channel DMX switch for switching loads up to 10 he DMX-switch operates on the standard DMX512 bus and requires 1 channel for operation. Version WD1558 he board ase ddress may be set between 1 and 512. Mechanical s Rated: V C. oard Requires mp Supply. Setup s Power and DMX Signal - 4-way block: Power: Ground (-) and Power +V connection = +V 12V 500ma DMX Network: 2 DMX Data - signal line connection (lack ) 3 DMX Data + signal line connection (White ) 3-Pin header - DMX termination resistor On/Off Jumper (RM) Output : 3-way lock - NO- Normal Open, C-Common, NC- Normal Closed Load connections- single pole double throw contacts rated at 10 / 240V C Settings - ( See DMX 512 ddress Chart for details ) Set the base address of Output using the DIP switches 1 through 10, as follows: dd the value of the address DIP switches set to the position to calculate the base address. Example: DIP switches 16 and 32 set to position, the base address is now 48, this setting is used to determine the starting address output of the ( see pages on ddressing for more details on addressing) oard defaults to address 1 if all address switches at OFF and to 512 if the address adds-up to more than 512. DMX LED- when a suitable DMX signal is being received or a flashing LED when NO valid DMX signal stream is being received by the 1-Ch DMX relay board. LED when the is activated. he board requires a 12V DC supply at 0.5 mps. Connect the relay board to the DMX network using 5-pin XLR connectors. If the DMX board is the last item on the network, place a jumper over the pins marked RM. his will improve the performance of the DMX network, acting as a DMX Network ermination. Connect the loads / devices to the relevant volt-free relay output. ( See relay setup and application example pages for details). is rated at 10 mps. Control Syntax - (See Pages on Control / ddressing) he output channel will go high () when the DMX transmitted value is selected. Value - 0 = OFF (0%) Value = ( 100%) Copyright 2010 ll Rights Reserved Phone (303) (MS)

2 DMX Network Setup - 5 Pin Overview Software US to DMX Interface US Cable US POR Computer US Cable US POR Control Software (VS) Laptop Computer DMX Control Console 5-Pin (M) XLR Connector DMX - XLR Cables 5-Pin (F) XLR Connector DMX wisted Pair White = 3 lack = 2 Data+ (2) 5-Pin (M) XLR Connector 5-Pin (F) XLR Connector 5-Pin (M) XLR Connector / OFF Closure pplications udio oard, Lights, Motors, FX NO C NC Data- (3) s DMX - XLR Cables 5 Pin XLR dapter s NC C 5-Pin (F) XLR Connector NO o Next DMX Device 2 3 DMX- 1-Ch oard Copyright 2010, ll Rights Reserved

3 Power oard op View Wall Plug Power Supply mp +Vin - Gnd oard Power XLR / Network DMX lack = 2 White = 3 wisted Pair Data+ (2) Data- (3) Mechanical oard Power + - DMX Network 2 3 erminal lock DMX LED RELY Power DMX Network ddressing DIP Switch Copyright 2010, ll Rights Reserved DMX Network ermination Jumper OFF Phone (303) (MS)

4 DMX Network Setup 5 Pin to End Overview Software US to DMX Interface US POR US Cable Computer Control Software (VS) Computer 5-Pin (M) XLR Connector US Cable US POR DMX Control Console DMX - XLR Cable DMX 1- Channel oard DMX IN Data+ (2) Data- (3) DMX lack = 2 White = Copyright 2010, ll Rights Reserved Phone (303) (MS)

5 Mechanical - Output Output NC - Normal Closed C- Common NO - Normal Open Copyright 2010, ll Rights Reserved Mechanical s Rated: V C. erminal lock Phone (303) (MS)

6 Version oard ddress DMX - Values Mechanical s Rated: V C. RELY Example oard Requires mp Supply. (CH=12) (Value= 255) ( = ) DIP Switches ( ddressing ) Switch Number Switch Position ( or OFF ) Switch Value OFF DMX Value = 0-100% 255=, 0= OFF 4+8 = 12 (CH=12) (Value= 0) ( = OFF) he DMX board provides 1- programmable Digital Outputs channel when connected to a DMX controlled network. he board ase ddress may be set between 1 and 512. Setting the base address of Output dd the value of the address DIP switches set to the position to calculate the base address. Example(CH): DIP switches 5 and 6 set to position, the base address is now 48, (16+32) this setting is used to determine the starting address output of the. Example DIp Switch 1 and 7 = ase ddress 65 Switch 1(1) + Switch 7(64) otal = 65 at DMX value 255 OFF at DMX value 0 DIp Switch 3 and 8 = ase ddress 132 Switch 3(4) + Switch 8(128) otal = 132 at DMX value 255 OFF at DMX value 0 DIp Switch 2 and 5 = ase ddress18 Switch 2(2) + Switch 5(15) otal = 18 at DMX value 255 OFF at DMX value = OFF Copyright 2010, ll Rights Reserved Phone (303) (MS)

7 DMX 512 ddress Chart Chart - US Standard DMX 512 Ch - Switches Ch - Switches Ch - Switches Ch - Switches Ch - Switches 1 = 1 2 = 2 3 = 1, 2 4 = 3 5 = 1, 3 6 = 2, 3 7 = 1, 2, 3 8 = 4 9 = 1, 4 10 = 2, 4 11 = 1, 2, 4 12 = 3, 4 13 = 1, 3, 4 14 = 2, 3, 4 15 = 1, 2, 3, 4 16 = 5 17 = 1, 5 18 = 2, 5 19 = 1, 2, 5 20 = 3, 5 21 = 1, 3, 5 22 = 2, 3, 5 23 = 1, 2, 3, 5 24 = 4, 5 25 = 1, 4, 5 26 = 2, 4, 5 27 = 1, 2, 4, 5 28 = 3, 4, 5 29 = 1, 3, 4, 5 30 = 2, 3, 4, 5 31 = 1, 2, 3, 4, 5 32 = 6 33 = 1, 6 34 = 2, 6 35 = 1, 2, 6 36 = 3, 6 37 = 1, 3, 6 38 = 2, 3, 6 39 = 1, 2, 3, 6 40 = 4, 6 41 = 1, 4, 6 42 = 2, 4, 6 43 = 1, 2, 4, 6 44 = 3, 4, 6, 45 = 1, 3, 4, 6 46 = 2, 3, 4, 6 47 = 1, 2, 3, 4, 6 48 = 5, 6 49 = 1, 5, 6 50 = 2, 5, 6 51 = 1, 2, 5, 6 52 = 3, 5, 6 53 = 1, 3, 5, 6 54 = 2, 3, 5, 6 55 = 1, 2, 3, 5, 6 56 = 4, 5, 6 57 = 1, 4, 5, 6 58 = 2, 4, 5, 6 59 = 1, 2, 4, 5, 6 60 = 3, 4, 5, 6 61 = 1, 3, 4, 5, 6 62 = 2, 3, 4, 5, 6 63 = 1, 2, 3, 4, 5, 6 64 = 7 65 = 1, 7 66 = 2, 7 67 = 1, 2, 7 68 = 3, 7 69 = 1, 3, 7 70 = 2, 3, 7 71 = 1, 2, 3, 7 72 = 4, 7 73 = 1, 4, 7 74 = 2, 4, 7 75 = 1, 2, 4, 7 76 = 3, 4, 7 77 = 1, 3, 4, 7 78 = 2, 3, 4, 7 79 = 1, 3, 4, 7 80 = 5, 7 81 = 1, 5, 7 82 = 2, 5, 7 83 = 1, 2, 5, 7 84 = 3, 5, 7 85 = 1, 3, 5, 7 86 = 2, 3, 5, 7 87 = 1, 2, 3, 5, 7 88 = 4, 5, 7 89 = 1, 4, 5, 7 90 = 2, 4, 5, 7 91 = 1, 2, 4, 5, 7 92 = 3, 4, 5, 7 93 = 1, 3, 4, 5, 7 94 = 2, 3, 4, 5, 7 95 = 1, 2, 3, 4, 5, 7 96 = 6, 7 97 = 1, 6, 7 98 = 2, 6, 7 99 = 1, 2, 6, = 3, 6, = 1, 3, 6, = 2, 3, 6, = 1, 2, 3, 6, = 4, 6, = 1, 4, 6, = 2, 4, 6, = 1, 2, 4, 6, = 3, 4, 6, = 1, 3, 4, 6, = 2, 3, 4, 6, = 1, 2, 3, 4, 6, = 5, 6, = 1, 5, 6, = 2, 5, 6, = 1, 2, 5, 6, = 3, 5, 6, = 1, 3, 5, 6, = 2, 3, 5, 6, = 1, 2, 3, 5, 6, = 4, 5, 6, = 1, 4, 5, 6, = 2, 4, 5, 6, = 1, 2, 4, 5, 6, = 3, 4, 5, 6, = 1, 3, 4, 5, 6, = 2, 3, 4, 5, 6, = 1, 2, 3, 4, 5, 6, = = 1, = 2, = 1, 2, = 3, = 1, 3, = 2, 3, = 1, 2, 3, = 4, = 1, 4, = 2, 4, = 1, 2, 4, = 3, 4, = 1, 3, 4, = 2, 3, 4, = 1, 2, 3, 4, = 5, = 1, 5, = 2, 5, = 1, 2, 5, = 3, 5, = 1, 3, 5, = 2, 3, 5, = 1, 2, 3, 5, = 4, 5, = 1, 4, 5, = 2, 4, 5, = 1, 2, 4, 5, = 3, 4, 5, = 1, 3, 4, 5, = 2, 3, 4, 5, = 1, 2, 3, 4, 5, = 6, = 1, 6, = 2, 6, = 1, 2, 6, = 3, 6, = 1, 3, 6, = 2, 3, 6, = 1, 2, 3, 6, = 4, 6, = 1, 4, 6, = 2, 4, 6, = 1, 2, 4, 6, = 3, 4, 6, = 1, 3, 4, 6, = 2, 3, 4, 6, = 1,2, 3, 4, 6, = 5, 6, = 1, 5, 6, = 2, 5, 6, = 1, 2, 5, 6, = 3, 5, 6, = 1, 3, 5, 6, = 2, 3, 5, 6, = 1, 2, 3, 5, 6, = 4, 5, 6, = 1, 4, 5, 6, = 2, 4, 5, 6, = 1, 2, 4, 5, 6, = 3, 4, 5, 6, = 1, 3, 4, 5, 6, = 2, 3, 4, 5, 6, = 1, 2, 3, 4, 5, 6, = 7, = 1, 7, 8, 194 = 2, 7, 8, 195 = 1, 2, 7, = 3, 7, = 1, 3, 7, = 2, 3, 7, = 1, 2, 3, 7, = 4, 7, 8, 201 = 1, 4, 7, = 2, 4, 7, = 1, 2, 4, 7, = 3, 4, 7, = 1, 3, 4, 7, = 2, 3, 4, 7, = 1, 2, 3, 4, 7, = 5, 7, = 1, 5, 7, = 2, 5, 7, = 1, 2, 5, 7, = 3, 5, 7, = 1, 3, 5, 7, = 2, 3, 5, 7, = 1, 2, 3, 5, 7, = 4, 5, 7, = 1, 4, 5, 7, = 2, 4, 5, 7, = 1, 2, 4, 5, 7, = 3, 4, 5, 7, = 1, 3, 4, 5, 7, = 2, 3, 4, 5, 7, = 1, 2, 3, 4, 5, 7, = 6, 7, = 1, 6, 7, = 2, 6, 7, = 1, 2, 6, 7, = 3, 6, 7, = 1, 3, 6, 7, = 2, 3, 6, 7, = 1, 2, 3, 6, 7, = 4, 6, 7, = 1, 4, 6, 7, = 2, 4, 6, 7, = 1, 2, 4, 6, 7, = 3, 4, 6, 7, = 1, 3, 4, 6, 7, = 2, 3, 4, 6, 7, = 1, 2, 3, 4, 6, 7, = 5, 6, 7, = 1, 5, 6, 7, = 2, 5, 6, 7, = 1, 2, 5, 6, 7, = 3, 5, 6, 7, = 1, 3, 5, 6, 7, = 2, 3, 5, 6, 7, = 1, 2, 3, 5, 6, 7, = 4, 5, 6, 7, = 1, 4, 5, 6, 7, = 2, 4, 5, 6, 7, = 1, 2, 4, 5, 6, 7, = 3, 4, 5, 6, 7, = 1, 3, 4, 5, 6, 7, = 2, 3, 4, 5, 6, 7, = 1, 2, 3, 4, 5, 6, 7, = = 1, = 2, = 1, 2, = 3, 9 Phone (303) (MS)

8 DMX 512 ddress Chart Cont. Ch - Switches Ch - Switches Ch - Switches Ch - Switches Ch - Switches 261 = 1, 3, = 2, 3, = 1, 2, 3, = 4, = 1, 4, = 2, 4, = 1, 2, 4, = 3, 4, = 1, 3, 4, = 2, 3, 4, = 1, 2, 3, 4, = 5, = 1, 5, = 2, 5, = 1, 2, 5, = 3, 5, = 1, 3, 5, = 2, 3, 5, = 1, 2, 3, 5, = 4, 5, = 1, 4, 5, = 2, 4, 5, = 1, 2, 4, 5, = 3, 4, 5, = 1, 3, 4, 5, = 2, 3, 4, 5, = 1, 2, 3, 4, 5, = 6, = 1, 6, = 2, 6, = 1, 2, 6, = 3, 6, = 1, 3, 6, = 2, 3, 6, = 1, 2, 3, 6, = 4, 6, = 1, 4, 6, = 2, 4, 6, = 1, 2, 4, 6, = 3, 4, 6, = 1, 3, 4, 6, = 2, 3, 4, 6, = 1, 2, 3, 4, 6, = 5, 6, = 1, 5, 6, = 2, 5, 6, = 1, 2, 5, 6, = 3, 5, 6, = 1, 3, 5, 6, = 2, 3, 5, 6, = 1, 2, 3, 5, 6, = 4, 5, 6, = 1, 4, 5, 6, = 2, 4, 5, 6, = 1, 2, 4, 5, 6, = 3, 4, 5, 6, = 1, 3, 4, 5, 6, = 2, 3, 4, 5, 6, = 1, 2, 3, 4, 5, 6, = 7, = 1, 7, = 2, 7, = 1, 2, 7, = 3, 7, = 1, 3, 7, = 2, 3, 7, = 1, 2, 3, 7, = 4, 7, = 1, 4, 7, = 2, 4, 7, = 1, 2, 4, 7, = 3, 4, 7, = 1, 3, 4, 7, = 2, 3, 4, 7, = 1, 2, 3, 4, 7, = 5, 7, = 1, 5, 7, = 2, 5, 7, = 1, 2, 5, 7, = 3, 5, 7, = 1, 3, 5, 7, = 2, 3, 5, 7, = 1, 2, 3, 5, 7, = 4, 5, 7, = 1, 4, 5, 7, = 2, 4, 5, 7, = 1, 2, 4, 5, 7, = 3, 4, 5, 7, = 1, 3, 4, 5, 7, = 2, 3, 4, 5, 7, = 1, 2, 3, 4, 5, 7, = 6, 7, = 1, 6, 7, = 2, 6, 7, = 1, 2, 6, 7, = 3, 6, 7, = 1, 3, 6, 7, = 2, 3, 6, 7, = 1, 2, 3, 6, 7, = 4, 6, 7, = 1, 4, 6, 7, = 2, 4, 6, 7, = 1, 2, 4, 6, 7, = 3, 4, 6, 7, = 1, 3, 4, 6, 7, = 2, 3, 4, 6, 7, = 1, 2, 3, 4, 6, 7, = 5, 6, 7, = 1, 5, 6, 7, = 2, 5, 6, 7, = 1, 2, 5, 6, 7, = 3, 5, 6, 7, = 1, 3, 5, 6, 7, = 2, 3, 5, 6, 7, = 1, 2, 3, 5, 6, 7, = 4, 5, 6, 7, = 1, 4, 5, 6, 7, = 2, 4, 5, 6, 7, = 1, 2, 4, 5, 6, 7, = 3, 4, 5, 6, 7, = 1, 3, 4, 5, 6, 7, = 2, 3, 4, 5, 6, 7, = 1, 2, 3, 4, 5, 6, 7, = 8, = 1, 8, = 2, 8, = 1, 2, 8, = 3, 8, = 1, 3, 8, = 2, 3, 8, = 1, 2, 3, 8, = 4, 8, = 1, 4, 8, = 2, 4, 8, = 1, 2, 4, 8, = 3, 4, 8, = 1, 3, 4, 8, = 2, 3, 4, 8, = 1, 2, 3, 4, 8, = 5, 8, = 1, 5, 8, = 2, 5, 8, = 1, 2, 5, 8, = 3, 5, 8, = 1, 3, 5, 8, = 2, 3, 5, 8, = 1, 2, 3, 5, 8, = 4, 5, 8, = 1, 4, 5, 8, = 2, 4, 5, 8, = 1, 2, 4, 5, 8, = 3, 4, 5, 8, = 1, 3, 4, 5, 8, = 2, 3, 4, 5, 8, = 1, 2, 3, 4, 5, 8, = 6, 8, = 1, 6, 8, = 2, 6, 8, = 1, 2, 6, 8, = 3, 6, 8, = 1, 3, 6, 8, = 2, 3, 6, 8, = 1, 2, 3, 6, 8, = 4, 6, 8, = 1, 4, 6, 8, = 2, 4, 6, 8, = 1, 2, 4, 6, 8, = 3, 4, 6, 8, = 1, 3, 4, 6, 8, = 2, 3, 4, 6, 8, = 1, 2, 3, 4, 6, 8, = 5, 6, 8, = 1, 5, 6, 8, = 2, 5, 6, 8, = 1, 2, 5, 6, 8, = 3, 5, 6, 8, = 1, 3, 5, 6, 8, = 2, 3, 5, 6, 8, = 1, 2, 3, 5, 6, 8, = 4, 5, 6, 8, = 1, 4, 5, 6, 8, = 2, 4, 5, 6, 8, = 1, 2, 4, 5, 6, 8, = 3, 4, 5, 6, 8, = 1, 3, 4, 5, 6, 8, = 2, 3, 4, 5, 6, 8, = 1, 2, 3, 4, 5, 6, 8, = 7, 8, = 1, 7, 8, = 2, 7, 8, = 1, 2, 7, 8, = 3, 7, 8, = 1, 3, 7, 8, = 2, 3, 7, 8, = 1, 2, 3, 7, 8, = 4, 7, 8, = 1, 4, 7, 8, = 2, 4, 7, 8, = 1, 2, 4, 7, 8, = 3, 4, 7, 8, = 1, 3, 4, 7, 8, = 2, 3, 4, 7, 8, = 1, 2, 3, 4, 7, 8, = 5, 7, 8, = 1, 5, 7, 8, = 2, 5, 7, 8, = 1, 2, 5, 7, 8, = 3, 5, 7, 8, = 1, 3, 5, 7, 8, = 2, 3, 5, 7, 8, = 1, 2, 3, 5, 7, 8, = 4, 5, 7, 8, = 1, 4, 5, 7, 8, = 2, 4, 5, 7, 8, = 1, 2, 4, 5, 7, 8, = 3, 4, 5, 7, 8, = 1, 3, 4, 5, 7, 8, = 2, 3, 4, 5, 7, 8, = 1, 2, 3, 4, 5, 7, 8, = 6, 7, 8, = 1, 6, 7, 8, = 2, 6, 7, 8, = 1, 2, 6, 7, 8, = 3, 6, 7, 8, = 1, 3, 6, 7, 8, = 2, 3, 6, 7, 8, = 1, 2, 3, 6, 7, 8, = 4, 6, 7, 8, = 1, 4, 6, 7, 8, = 2, 4, 6, 7, 8, = 1, 2, 4, 6, 7, 8, = 3, 4, 6, 7, 8, = 1, 3, 4, 6, 7, 8, = 2, 3, 4, 6, 7, 8, = 1, 2, 3, 4, 6, 7, 8, = 5, 6, 7, 8, 9, 497 = 1, 5, 6, 7, 8, = 2, 5, 6, 7, 8, = 1, 2, 5, 6, 7, 8, = 3, 5, 6, 7, 8, = 1, 3, 5, 6, 7, 8, = 2, 3, 5, 6, 7, 8, = 1, 2, 3, 5, 6, 7, 8, = 4, 5, 6, 7, 8, 9 Copyright 2010, ll Rights Reserved 505 = 1, 4, 5, 6, 7, 8, = 2, 4, 5, 6, 7, 8, = 1, 2, 4, 5, 6, 7, 8, = 3, 4, 5, 6, 7, 8, = 1, 3, 4, 5, 6, 7, 8, = 2, 3, 4, 5, 6, 7, 8, = 1, 2, 3, 4, 5, 6, 7, 8, = 0 US Standard DMX = 422 Example DIP Switches ( ddressing ) ddress Switch Value Switch Number ddress = 422 Switch = 2, 3, 6, 8, 9 OFF Switch Position ( or OFF )

9 pplications Pneumatic Setup ir Supply ir Hose ir Hose 5/2 Switching Solenoid ir Valve (12 VDC) ir Hose Exhaust Ports + 12 Vdc - 12 Vdc + 12 Vdc 12 Vdc Power Supply No. 8 C NO Pneumatic Cylinder (Double cting) NC - Normal Closed ( Not Used) C- Common NO - Normal Open DMX- 1 Channel oard erminal locks Copyright 2010, ll Rights Reserved Phone (303) (MS)

10 pplication Motor Control DC Motor LCK MOOR POWER (12Vdc) -Gnd C- Common RED NO - Normal Open +V Rotation CCW Switch Motor s / to Change Direction Rotation CW 12 Volt DC Permanent Magnet Motor Copyright 2010, ll Rights Reserved Phone (303) (MS)

11 pplications (12 Vdc) + - LED-Light ars (12 Vdc) + - (-) (+) LED Resistor LED's Resistors 330 Ohm C- Common to LED ar, and Single LED's NO - Normal Open RED LCK Copyright 2010, ll Rights Reserved +V -Gnd LED POWER (12Vdc) Phone (303) (MS)

12 pplications MP3 / Sound oard Playback OPIL PLYCK Speaker and mplifier (Stereo Output) udio mp & Speaker R1 PLYCK Stereo Sound System SD Card MP3 Player oard Power DMX 1-Ch to MP3 Player DMX- 1 Ch oard Remote Switch or rigger Input MP3 Player oard C s NO Copyright 2010, ll Rights Reserved Phone (303) (MS)

13 pplication DMX Hybrid - Set-up Wizard oard Control o Servos, Motors, Light FX & Sound Effect Playback OHER Wizard / Puppet Controllers o Servomotors and Digital Output Channels Wizard - 8 Controller oard Wizard - 11 Controller oard Wizard - 1 Controller oard Wizard oard REM Port s (2-) o VC Devices & Sound Effects Playback o Servos, Motors, Light FX & Sound Effect Playback Wizard REM Port ctivation by DMX- 1 Ch Wizard - 3 Controller oard o Motors, Light s, LED's Special Effect Devices C NO DMX- 1 Ch oard Copyright 2010, ll Rights Reserved Wizard - 2 Controller oard Phone (303) (MS)

14 * Use caution when working with C Voltage. ouching or incorrectly wiring this circuit could cause serious personal injury or damage to equipment. DNGER * Power ransformer ( 5-12 VDC) White 5-12 VDC - + * Wall Plug Caution Green (Gnd) White lack DNGER lack * 1 2 CRYDOM 4 +3 Red lack * Plug In C Voltage pplication Large C Power Control Solid-State Module C Contacts NO Caution C Powered Devices DMX- 1 Ch oard Copyright 2010, ll Rights Reserved Phone (303) (MS)

15 Notes / Worksheet: DMX RELY ORD NO: DMX RELY ORD pplication: Worksheet W Version ddressing Output pplication -1 RM = ( /OFF) Switch Number Switch Position ( or OFF ) Switch Value Copyright 2010, ll Rights Reserved 256 Switch Positions (UP / Down ) 512 OFF DMX Value = 0-100% 255=, 0= OFF UP OFF Down SW-1 SW-2 SW-3 SW-4 SW-5 SW-6 SW-7 SW-8 SW-9 SW-10 ddressing 1 = 0 = OFF Value DMX 0 1 OFF Position Phone (303) (MS)

Blue Point Engineering

Blue Point Engineering DMX -Channel Relay Board Overview A two-channel DMX relay switch for switching loads up to 0A at 40V AC per channel. he DMX switch operates on the standard DMX5 bus and requires - DMX channels for operation.

More information

Blue Point Engineering

Blue Point Engineering lue Point Engineering Wizard - I Interface oard http://www.pesolutions.com (303) 651.3794 Pointing the Way to Solutions! Talking / Eye Moving Skull Connectors pplication Examples 7805 Eyeball Jar nimatronic

More information

DMX Digital-Servo Board

DMX Digital-Servo Board Version 1.0 2012 WD197 Overview he DMX DigitalServo module is designed to provide 8 consecutive channels of output from a standard DMX protocol input signal. he outputs may be configured to be 5VDC digital

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering Instruction I www.bpesolutions.com Pointing the Way to Solutions! Animatronic Wizard - 3 Board (BPE No. WAC-0030) Version 3.0 2009 Controller Page 1 The Wizard 3 Board will record

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering Instruction I www.bpesolutions.com Pointing the Way to Solutions! Puppet - II+ Controller (BPE No. PCA-0001) Servo Position Adjustment EEPROM Digital Button Power 5 Vdc Playback

More information

Blue Point Engineering Inc.

Blue Point Engineering Inc. Engineering Inc. ireless Radio Control of Puppets Setup Overview RF Control C Pointing the ay to Solutions! Hardware Setup Overview Page 1 Servo No.1 Servo No.2 Control Signal Line RX8ch1,2 Servo Board

More information

Blue Point Engineering

Blue Point Engineering Overview Blue Point Instruction Board 2-CH Boards, Terminal Block and Ribbon Cable I Type: RF Radio (315 MHz) 1-2 Channels (FCC Part 15 Compliant Components). Operating Voltage: 6-15 VDC @ 1 Amp (Wall

More information

Contents. Warranty and Disclaimer 2 Introduction 3

Contents. Warranty and Disclaimer 2 Introduction 3 Contents Warranty and Disclaimer 2 Introduction 3 Physical Dimensions Board Layout 4 Usage Using the Relay board 5 Setting the start address 5 Configuration Jumper 6 Using the Relays 7 Using the DMX connectors

More information

TEAM DIGITAL. SMC4 Servo & Motor Controller

TEAM DIGITAL. SMC4 Servo & Motor Controller 16 CV# Function/Default Value CV# Function/Default Value 28 reserved - 73 Servo 3 Behavior 0 29 Decoder Configuration 0 74 Servo 4 Behavior 0 30 reserved - 75 Output Flash 0 31 Ops Mode Loco Address 1

More information

USER S MANUAL. C41 VARIABLE SPEED CONTROL Rev. 2 User manual Rev. 1

USER S MANUAL. C41 VARIABLE SPEED CONTROL Rev. 2 User manual Rev. 1 USER S MANUAL C41 VARIABLE SPEED CONTROL Rev. 2 User manual Rev. 1 JUNE 2013 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 OVERVIEW... 2 2.0 FEATURES... 2 3.0 SPECIFICATIONS... 3 4.0 INSTALLATION

More information

BOSSCOM Powerlink 2-in-1

BOSSCOM Powerlink 2-in-1 BOSSCOM Powerlink 2-in-1 User manual Content Basic Applications... 3 Plug & Play... 3 Intallation... 4 Special Applications with an IR-receiver Connected... 5 Option Programming... 6 Specifications...

More information

Analog Servo Drive 20A20

Analog Servo Drive 20A20 Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

Blue Point Engineering Inc.

Blue Point Engineering Inc. nc. Wireless Radio Control of Puppets Setup Overview RF Control C Hardware Setup Overview Servo No.1 Servo No.2 Control Signal Line RX8-ch1,2 Servo Board WZ-12 RX8-ch3,4 Servo Board WZ-12 Power Line DC

More information

AxCent Servo Drive A25A100

AxCent Servo Drive A25A100 Description Power Range The A25A100 PWM servo drive is designed to drive brush type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected

More information

ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder)

ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder) ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder) Traditional stepper motor drive systems operate open loop providing position control without feedback. However, because of this,

More information

Integrated Servo Motor UCS57

Integrated Servo Motor UCS57 Integrated Servo Motor Introduction is a new generation of high performance digital integrated servo drive motor, which is a series of low voltage AC servo products integrated with AC servo motor and drive

More information

RC Camera Control. User Guide v1.3 (RCCC v1.1) 11/7/2012

RC Camera Control. User Guide v1.3 (RCCC v1.1) 11/7/2012 RC Camera Control User Guide v1.3 (RCCC v1.1) 11/7/2012 kristaps_r@rcgroups INTRODUCTION RC Camera Control board (RCCC) is multifunctional control board designed to for aerial photography or First Person

More information

MTC-2 highlight features: ACU highlight features: Contents. MTC-2 and ACU User Manual V5.1

MTC-2 highlight features: ACU highlight features: Contents. MTC-2 and ACU User Manual V5.1 MTC-2 can work alone as a twin motor ECS (electronic speed controller) for RC tanks. When the ACU (auxiliary control unit) is connected, it can also control turret rotation, gun elevation, gun firing,

More information

MTC-2 highlight features: ACU highlight features: Contents. MTC-2 and ACU User Manual V4.0

MTC-2 highlight features: ACU highlight features: Contents. MTC-2 and ACU User Manual V4.0 MTC-2 can work alone as a twin motor ECS (electronic speed controller) for RC tanks. When the ACU (auxiliary control unit) is connected, it can also control turret rotation, gun elevation, gun firing,

More information

ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder)

ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder) ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder) Traditional stepper motor drive systems operate open loop providing position control without feedback. However, because of this,

More information

2007 MFJ ENTERPRISES, INC.

2007 MFJ ENTERPRISES, INC. Model MFJ-643 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551 VERSION

More information

Evolution. EC Motor Series 1. Automation Interface CONTROLS INC. EVO /ECM-ACU+ Application. Ordering

Evolution. EC Motor Series 1. Automation Interface CONTROLS INC. EVO /ECM-ACU+ Application. Ordering Evolution Automation Interface COTROLS IC. EVO /ECM-ACU+ EC Motor Series 1 Application The allows industry standard 0V to +10V automation signals to adjust and monitor EC Motors. These are fractional horsepower

More information

Hardware Guide. Control Made Simple. Model 401A Signal Generator

Hardware Guide. Control Made Simple. Model 401A Signal Generator Control Made Simple Model 401A Signal Generator Hardware Guide ON OFF LIMIT 1 2 3 4 RXD TXD POWER West Coast Office 1263 El Camino Real Menlo Park, CA 94025 Phone (650) 853-1444 Fax (650) 853-1405 www.flashcutcnc.com

More information

Analog Servo Drive 30A8

Analog Servo Drive 30A8 Description Power Range The 30A8 PWM servo drive is designed to drive brush type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected

More information

SUNRISE UPGRADE KIT for LAI "SkillTester"

SUNRISE UPGRADE KIT for LAI SkillTester SUNRISE UPGRADE KIT for LAI "SkillTester" This upgrade is designed to suit the early model LAI Skill Tester machines. These machines have a Move Forward and a Move Right button, and no sound effects. The

More information

MTC-2 highlight features: ACU for Flakpanzer Gepard highlight features: Contents. MTC-2 and ACU User Manual V4.2 (Flakpanzer Gepard Version)

MTC-2 highlight features: ACU for Flakpanzer Gepard highlight features: Contents. MTC-2 and ACU User Manual V4.2 (Flakpanzer Gepard Version) This manual is written for the ACU for Flakpanzer Gepard. There are some modifications on usage of servo and LED ports. Please also notice that GSU (gun stabilize unit) is not supported. MTC-2 highlight

More information

67TD Series - Miniature Time Delay Relays DPDT, 4PDT, 5 Amp

67TD Series - Miniature Time Delay Relays DPDT, 4PDT, 5 Amp TD Series - Miniature Time Delay Relays DPDT, PDT, mp E When small size is a requirement series relays fit where others won t. The miniature ice cube timers are capable of handling up to amps. Typical

More information

Octasound RAMX2 V2.0 - Setting the Jumpers

Octasound RAMX2 V2.0 - Setting the Jumpers Octasound RMX2 V2.0 - Setting the Jumpers The first requirement for the RMX2 to work according to your installation is to set the jumpers according to the charts below. With the new version of the mixer

More information

C41 VARIABLE SPEED CONTROL Rev. 1.1

C41 VARIABLE SPEED CONTROL Rev. 1.1 C41 VARIABLE SPEED CONTROL Rev. 1.1 User manual Rev.1 1. Overview This card lets you control your spindle with PWM and direction signals, as if it was an axis motor. It converts the step signal into and

More information

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input Ndrive PWM Amplifiers/Drives Ndrive Series Digital Servo Amplifiers PWM Wide output power range from 10 A peak to 200 A peak at 320 VDC 2- or 3-phase AC line input or DC input CE approved and NRTL safety

More information

Analog Servo Drive 30A20AC

Analog Servo Drive 30A20AC Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

Contents. Warranty and Disclaimer 2

Contents. Warranty and Disclaimer 2 Contents Warranty and Disclaimer 2 Physical Dimensions Board Layout 3 Usage Using the PWM board 4 Setting the start address 4 Dimming LED s 5,6 Typical hookup 7 Terminator 8 Troubleshooting Ground, termination,

More information

Crown CDi Amplifier Set-Up

Crown CDi Amplifier Set-Up Crown CDi Amplifier Set-Up For Origin Landscape Speakers Models: CDi1000 CDi2000 CDi4000 TABLE OF CONTENTS Introduction 2 Crown Amplifier Ins & Outs 2 Input Connections 2 Unbalanced (Most Common) 2 Balanced

More information

Blue Point Engineering

Blue Point Engineering DMX Data Analyzer Board nstruction Overview DMX Analyzer - Tester PC Board Design your own enclosure with an analyzer / tester display or add to your existing equipment or system. The DMX Analyzer is a

More information

Analog Servo Drive 30A8

Analog Servo Drive 30A8 Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

TEAM DIGITAL. Servette TM Single Servo Controller

TEAM DIGITAL. Servette TM Single Servo Controller 12 7 Summary of Configuration Variables CV# Function/Default Value CV# Function/Default Value 1 Servo Address 1 43 reserved - 2 reserved - 44 Sec Input Control 26 3 Servo Move Range 15 45 reserved - 4

More information

FIRST Robotics Control System

FIRST Robotics Control System 2018/2019 FIRST Robotics Control System Team 236 1 (click on a component to go to its slide) 2 The Robot Powered solely by 12V battery RoboRIO- is the computer on the robot Controlled by Java code on the

More information

CABINET POWERED MIXING CONSOLE

CABINET POWERED MIXING CONSOLE R SHS AUDIO SPMU- 00 CABINET POWERED MIXING CONSOLE USER'S MANUAL SAFETY INSTRUCTIONS SPECIFICATIONS Inputs Input modes Input Impedance Rated Input level Connector WARNING - TO REDUCE THE RISK OF FIRE

More information

AxCent Servo Drive A50A100

AxCent Servo Drive A50A100 Description Power Range The A50A100 PWM servo drive is designed to drive brushed type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected

More information

TEAM DIGITAL. SC82 Servo Controller

TEAM DIGITAL. SC82 Servo Controller TEAM DIGITAL SC Servo Controller Improving the world of DCC > DCC compatible accessory decoder > Control servos motors > Output status LEDs > inputs for turnout control > 6 inputs for semaphore signaling

More information

30-80V, 8.2A Peak, No Tuning, Nulls loss of Synchronization

30-80V, 8.2A Peak, No Tuning, Nulls loss of Synchronization 2-phase Hybrid Servo Drive 30-80V, 8.2A Peak, No Tuning, Nulls loss of Synchronization Closed-loop, eliminates loss of synchronization Broader operating range higher torque and higher speed Reduced motor

More information

ES86 Series Closed-loop Stepper Drive + Motor System (ES-D808 Drive+ Motor/Encoder)

ES86 Series Closed-loop Stepper Drive + Motor System (ES-D808 Drive+ Motor/Encoder) ES86 Series Closed-loop Stepper Drive + Motor System (ES-D808 Drive+ Motor/Encoder) Traditional stepper motor drive systems operate open loop providing position control without feedback. However, because

More information

Product Manual QD1010-USB. Description. Contents. Material List. Setup. General Use. USB Cable Use. USB to RS485 Communications Converter

Product Manual QD1010-USB. Description. Contents. Material List. Setup. General Use. USB Cable Use. USB to RS485 Communications Converter Product Manual QD00-US US to Communications Converter Description The QD00-US is a US to converter used to allow asys Controls controllers to communicate with a PC. Material List QD00-US communication

More information

8 Channel, DMX to 0 10 volt, Decoder board

8 Channel, DMX to 0 10 volt, Decoder board 8 Channel, DMX to 0 10 volt, Decoder board Allows DMX512 digital protocol to control analog devices that require a 0-10VDC control voltage. Upgrade 0-10 volt analog dimmers, use with motor controllers

More information

Analog Servo Drive 100A40

Analog Servo Drive 100A40 Description Power Range The 100A40 PWM servo drive is designed to drive brush type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected

More information

Radio Control Installation and Operating Instructions System 4

Radio Control Installation and Operating Instructions System 4 Radio Control Installation and Operating Instructions System 4 P.O. Box 403, One Cedar Parkway, Jackson, WI 53037 Phone: 800-628-1909 Fax: 262-677-2058 Revision: April 19, 2012 Contents Introduction 3

More information

Contents. Warranty and Disclaimer 2 Introduction 3

Contents. Warranty and Disclaimer 2 Introduction 3 Contents Warranty and Disclaimer 2 Introduction 3 Physical Dimensions Board Layout 4 Servo connections 5 Using the Serv8 Usage 6 Setting the start address 7 Setting the pulse width 8 Using the configuration

More information

Operation/Reference Guide NXP-CPI16. NetLinx Custom Panel Interface. Custom Panel Interfaces

Operation/Reference Guide NXP-CPI16. NetLinx Custom Panel Interface. Custom Panel Interfaces Operation/Reference Guide NXP-CPI16 NetLinx Custom Panel terface Custom Panel terfaces Last Revised: 5/18/2012 AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material

More information

BAND AIDE AUTOMATIC BAND DECODER

BAND AIDE AUTOMATIC BAND DECODER BAND AIDE AUTOMATIC BAND DECODER 1. Features Overview The Top Ten Devices Band Aide is an accessory that attaches to your radio (or computer), decodes the band data provided by the radio, and provides

More information

DMX-K-DRV-23 Integrated Step Motor Driver & Basic Controller

DMX-K-DRV-23 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-23 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-23 Manual - 1 - rev 1.35 COPYRIGHT 2013 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.

More information

MILFORD INSTRUMENTS Limited

MILFORD INSTRUMENTS Limited MILFORD INSTRUMENTS Limited DMX Receiver (#1-497) Rev1.5 09/01/2007 The DMX receiver module is designed to provide 8 consecutive channels of output from a standard DMX protocol input signal. The outputs

More information

Electromechanical Automation Technical Bulletin

Electromechanical Automation Technical Bulletin Electromechanical Automation Technical Bulletin Bulletin # TB438 Date: January 7, 2008 To: Distribution Product: TQ10, TQ10SD, TQ10X Subject: Upgrading TQ10 applications to Aries Parker Electromechanical

More information

Adjustable Parametric Equalizer Hardware Description

Adjustable Parametric Equalizer Hardware Description Adjustable Parametric Equalizer Hardware Description Adam Grunke April 27, 2004 ETEC 474 Professor Morton Introduction The Adjustable Parametric Equalizer (APE) allows the professional audio engineer to

More information

MODEL NC221 MOBILE TWO-TONE SEQUENTIAL DECODER INSTRUCTION MANUAL

MODEL NC221 MOBILE TWO-TONE SEQUENTIAL DECODER INSTRUCTION MANUAL 15385 Carrie Drive Grass Valley, CA 95949 Office: (530) 477-8400 Tech. Support: (530) 477-8402 FAX: (530) 477-8403 Sales: (800) 874-8663 Email: tech@norcommcorp.com Web:www.norcommcorp.com MODEL NC221

More information

2. Avoid metal objects coming into contact with this product. Protect the solder joints on the bottom of the PCB when mounting this product.

2. Avoid metal objects coming into contact with this product. Protect the solder joints on the bottom of the PCB when mounting this product. User s Guide and Specifications AMP2X15 Audio Amplifier Board PUI Audio s AMP2X15 audio amplifier board features a Texas Instruments TPA3110D2 Class D amplifier circuit for maximum signal fidelity; delivering

More information

Bholanath. User s Manual. Precision Engineering Pvt.Ltd. BHSSD Step Servo Driver. Note:-

Bholanath. User s Manual. Precision Engineering Pvt.Ltd. BHSSD Step Servo Driver. Note:- Bholanath Precision Engineering Pvt.Ltd. User s Manual Step Servo - BHSS - 750 W BHSSD Step Servo Driver Note:- Step servo drive & motor are matched pair with BH-75Vac power supply Email : support@bholanath.in

More information

CL86T. 24~80VDC, 8.2A Peak, Closed-loop, No Tuning. Descriptions. Closed-loop. Stepper. Applications. Datasheet of the Closed-loop Stepper CL86T

CL86T. 24~80VDC, 8.2A Peak, Closed-loop, No Tuning. Descriptions. Closed-loop. Stepper. Applications. Datasheet of the Closed-loop Stepper CL86T CL86T Closed-loop Stepper 24~80VDC, 8.2A Peak, Closed-loop, No Tuning Closed-loop, eliminates loss of synchronization Broader operating range higher torque and higher speed Reduced motor heating and more

More information

Installation & Operating Instructions

Installation & Operating Instructions FX (513) 4895243 Installation & Operating Instructions utomax electric actuators with servo control are factory adjusted for 90 degree operation and shipped in the full clockwise position as viewed from

More information

TOP SERVO SIGNAL 5 SERVO SIGNAL 3 SERVO SIGNAL 4 SERVO SIGNAL 6 T B T B T B T B T B SERVO TRIGGER 1 BOTTOM

TOP SERVO SIGNAL 5 SERVO SIGNAL 3 SERVO SIGNAL 4 SERVO SIGNAL 6 T B T B T B T B T B SERVO TRIGGER 1 BOTTOM Micro Miniatures Servo Controller Channel Location of connections and switches TOP SERVO SIGNAL SERVO SIGNAL 7 SERVO SIGNAL 6 SERVO SIGNAL 5 SERVO SIGNAL SERVO SIGNAL SERVO SIGNAL SERVO SIGNAL SIGNAL COMMON

More information

ZM 84 Audio Mixer. User Manual. Order code: CRAM41. Audio Mixer ZM 84 AUX 3 AUX 1 AUX 2 AUX 4 MASTER 1 MASTER 2 OFF BASS BASS TREBLE TREBLE BASS BASS

ZM 84 Audio Mixer. User Manual. Order code: CRAM41. Audio Mixer ZM 84 AUX 3 AUX 1 AUX 2 AUX 4 MASTER 1 MASTER 2 OFF BASS BASS TREBLE TREBLE BASS BASS ZM 84 Audio Mixer User Manual -20-10 0 +10 +20-20 -10 0 +10 +20 POWER L R 0 0 ON ZM 84 Audio Mixer AUX 4 MIC/LINE 1 MIC/LINE 1 MIC/LINE 2 MIC/LINE 3 MIC/LINE 4 THR THR +6 +10 +6 AUX 3 AUX 1 AUX 2 AUX 4

More information

SF Series. 900 MHz Wireless Switch Follower/Remote Control Receiver (with On-Board 10-Amp Relays) Typical Applications

SF Series. 900 MHz Wireless Switch Follower/Remote Control Receiver (with On-Board 10-Amp Relays) Typical Applications Long Range Wireless Applications 900 MHz Wireless Switch Follower/Remote Control Receiver (with On-Board 10-Amp Relays) The switch followers are a two way system designed to provide a quick and cost effective

More information

MFJ ENTERPRISES, INC.

MFJ ENTERPRISES, INC. TM Model MFJ-1924 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment! MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551

More information

DMX-K-DRV-17 Integrated Step Motor Driver & Basic Controller

DMX-K-DRV-17 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-17 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-17 Manual - 1 - rev 1.35 COPYRIGHT 2015 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.

More information

INSTALLATION AND CONNECTIONS Section 2

INSTALLATION AND CONNECTIONS Section 2 STLLTION ND CONNECTIONS Section Unpacking - ntenna jumper cable connection - Selecting a location - Rack mounting handle attachment - Grounding -3 ntenna connection -3 CF (Compact Flash) memory card -3

More information

Peak Current. Continuous Current. See Part Numbering Information on last page of datasheet for additional ordering options.

Peak Current. Continuous Current. See Part Numbering Information on last page of datasheet for additional ordering options. Description Power Range The PWM servo drive is designed to drive brushless DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected against

More information

Lab 2.4 Arduinos, Resistors, and Circuits

Lab 2.4 Arduinos, Resistors, and Circuits Lab 2.4 Arduinos, Resistors, and Circuits Objectives: Investigate resistors in series and parallel and Kirchoff s Law through hands-on learning Get experience using an Arduino hat you need: Arduino Kit:

More information

ServoDMX OPERATING MANUAL. Check your firmware version. This manual will always refer to the most recent version.

ServoDMX OPERATING MANUAL. Check your firmware version. This manual will always refer to the most recent version. ServoDMX OPERATING MANUAL Check your firmware version. This manual will always refer to the most recent version. WORK IN PROGRESS DO NOT PRINT We ll be adding to this over the next few days www.frightideas.com

More information

DigiSpeed DC-03. Isolated Control Voltage Generator User s Guide. PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84

DigiSpeed DC-03. Isolated Control Voltage Generator User s Guide. PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84 DigiSpeed DC-03 - Users Guide Page 1 Updated: 29. April 2009 DigiSpeed DC-03 Isolated Control Voltage Generator User s Guide PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84 DigiSpeed DC-03 - Users

More information

F O R T H E L O V E O F M U S I C SERIES 218 DPS200 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION

F O R T H E L O V E O F M U S I C SERIES 218 DPS200 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION F O R T H E L O V E O F M U S I C SERIES 218 DPS200 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION You have purchased an amplifier that leads the way with sound quality, reliability, and features.

More information

MFJ ENTERPRISES, INC.

MFJ ENTERPRISES, INC. Screwdriver Antenna Controller Model MFJ-1926 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment! MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel:

More information

3DM phase Digital Stepper Drive

3DM phase Digital Stepper Drive 3DM2283 3-phase Digital Stepper Drive 150-220VAC, 0.5-8.2A peak, Auto-configuration, Low Noise Anti-Resonance provides optimal torque and nulls mid-range instability Motor auto-identification and parameter

More information

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input Ndrive PWM Amplifiers/Drives Ndrive Series Digital Servo Amplifiers PWM Wide output power range from 10 A peak to 200 A peak at 320 VDC 2- or 3-phase AC line input or DC input CE approved and NRTL safety

More information

WTDIN-M. eeder. Digital Input Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies

WTDIN-M. eeder. Digital Input Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies eeder Technologies 90-A Beal Pkwy NW, Fort Walton Beach, FL 32548 www.weedtech.com 850-863-5723 Digital Input Module FEATURES 8 wide-range digital input channels with high voltage transient protection.

More information

Introduction to Arduino HW Labs

Introduction to Arduino HW Labs Introduction to Arduino HW Labs In the next six lab sessions, you ll attach sensors and actuators to your Arduino processor This session provides an overview for the devices LED indicators Text/Sound Output

More information

COMMERCIAL AUDIO SOLUTIONS FOR COMMERCIAL AUDIO AND PUBLIC ADRESS INSTALLATIONS

COMMERCIAL AUDIO SOLUTIONS FOR COMMERCIAL AUDIO AND PUBLIC ADRESS INSTALLATIONS COMMERCIAL AUDIO SOLUTIONS FOR COMMERCIAL AUDIO AND PUBLIC ADRESS INSTALLATIONS Pre-amplifiers, zonemixers, matrix mixers, amplifiers, mixer amplifiers, zonemixer amplifiers, DSP processors, DSP matrix

More information

Continental Hydraulics Installation Manual CEM-RA-A

Continental Hydraulics Installation Manual CEM-RA-A CEM-RA-A Description: This ramp amplifier drives either single or dual solenoid proportional valve coils up to 2.6A. It is suitable to control current to either proportional directional, flow, or pressure

More information

Technical Application Note #4

Technical Application Note #4 CRC CACTUS Radio Club, Inc. This Technical Application Note describes the modifications that need to be incorporated into a Link Communications RLC series controller to achieve near Cactus Standard Audio

More information

F O R T H E L O V E O F M U S I C LP100 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION

F O R T H E L O V E O F M U S I C LP100 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION F O R T H E L O V E O F M U S I C LP100 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION You have purchased an amplifier that leads the way with sound quality, reliability, and features. These high performance

More information

WTDOT-M. eeder. Digital Output Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies

WTDOT-M. eeder. Digital Output Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies eeder Technologies 90-A Beal Pkwy NW, Fort Walton Beach, FL 32548 www.weedtech.com 850-863-5723 Digital Output Module FEATURES 8 high-current open-collector output channels with automatic overload shutdown.

More information

HT101V Reference Manual

HT101V Reference Manual HT101V Reference Manual Overview The HT101V from Ag-Tester is our handheld tester designed to diagnose valve components on agricultural machinery. Valves tested include: 1- Boom Control Valves 2- Servo

More information

DBK17. 4-Channel Simultaneous Sample and Hold Card. Overview

DBK17. 4-Channel Simultaneous Sample and Hold Card. Overview DBK17 4-Channel Simultaneous Sample and Hold Card Overview... 1 Simultaneous Sample and Hold... 2 Hardware Setup... 2 Card Connection... 2 Card Configuration... 2 CE Compliance... 3 DaqBook/100 Series

More information

MA80FT Mini Amplifier

MA80FT Mini Amplifier MA8FT Mini Amplifier LF HF MA8FT 8W MIXER AMPLIFIER OFF 1 OFF 1 STATUS MUTE PEAK OFF 1-1 db +1-1 db +1 MUSIC EQ MA8FT Front Panel PAGE/ INPUT +5 +1 db HI-Z SPKR IN 7/ - -1V SETTINGS 1: / PAGE MODE 2: /

More information

3. WHEN TO TURN ON. Always turn the Tx on first, unless binding. Always turn Rx off first.

3. WHEN TO TURN ON. Always turn the Tx on first, unless binding. Always turn Rx off first. - 2 - IF PICS ARE NOT CLEAR ENOUGH, PLEASE DOWNLOAD AND PRINT OUT https://www.rcs-rc.com/store/pdf/instructions/receivers/rx102-1(ab)lr.pdf 2. FEATURES. Purpose: Rx102-1(AB)LR Live Steam & Low OFF Batt

More information

Installation Tech Note Dallas, Texas

Installation Tech Note Dallas, Texas AMC B40A40AC Installation Tech Note Dallas, Texas May, 2010 ! CAUTION! Do NOT apply air pressure to release the collet while the servo motor is rotating. The servo motor spindle must be FULLY STOPPED before

More information

Z44R. Multi-purpose Rack Mixer. Item ref: User Manual

Z44R. Multi-purpose Rack Mixer. Item ref: User Manual Z44R Multi-purpose Rack Mixer Item ref: 953.020 User Manual 2 balanced microphone inputs Lo-cut rumble filters 3-band EQ per Mic channel Switchable 48V phantom power 2 x A/B selectable stereo line inputs

More information

Interface Genius Modem Instruction Manual v1.2.4

Interface Genius Modem Instruction Manual v1.2.4 Interface Genius Modem Instruction Manual v1.2.4 Interface Genius Modem is a USB / LAN controlled SO2R radio interface remote radio modem. It is designed to be controlled by a Windows application, and

More information

STANDARD WIRING DIAGRAMS FOR SMART MODEL 20

STANDARD WIRING DIAGRAMS FOR SMART MODEL 20 CODING SYSTEM FOR AV ACTUATOR WIRING DIAGRAMS There are 3 elements to the wiring codes used in AVA electric actuators: WIRING CODE 1 3 Wire system, single pole double throw, switching the live SPDT 2 3

More information

The MaxPlus SFD 230 Connectivity and ease of use in a compact, cost-effective digital solution.

The MaxPlus SFD 230 Connectivity and ease of use in a compact, cost-effective digital solution. SFD Digital Drive Overview The MaxPlus SFD 0 Connectivity and ease of use in a compact, cost-effective digital solution. Meeting your expectations. t the MTS Systems Corporation, utomation Division, we

More information

INSTRUCTION MANUAL. AZGTi Mount. Copyright Sky-Watcher

INSTRUCTION MANUAL. AZGTi Mount. Copyright Sky-Watcher INSTRUCTION MANUAL AZGTi Mount Copyright Sky-Watcher CONTENT Parts Diagram PART I : SETTING UP THE AZGTi MOUNT 1.1 Setting up on a Skywatcher Tripod...4 1. Attaching the AZGTi Mount to a camera tripod...5

More information

BFS / BFSM SERIES Installation & Maintenance Manual

BFS / BFSM SERIES Installation & Maintenance Manual Introduction: The BFS / BFSM series electric actuators have battery backup modules for fail safe operation. The BFS series is for two position control and the BFSM series is for proportional control, both

More information

No Gain Tuning. Hunting. Closed Loop System

No Gain Tuning. Hunting. Closed Loop System 2 No Gain Tuning Conventional servo systems, to ensure machine performance, smoothness, positional error and low servo noise, require the adjustment of its servo s gains as an initial crucial step. Even

More information

S1 Programming Chart Program Description S1 Switch Positions. Constant ON High/Low Track, WR

S1 Programming Chart Program Description S1 Switch Positions. Constant ON High/Low Track, WR RODIX INC. FEEDER CUBE FC90 Plus Series ADVANCED FEATURES Optional software features of the 24490 / 2449 circuit boards OVERVIEW: The FC90 Plus Series of feeder controls are built around the circuit boards

More information

instruction manual for Open LRS New Generation

instruction manual for Open LRS New Generation instruction manual for Open LRS New Generation Table of contents 1. Important warnings 2. Hardware Overview 3 2.1 DTF UHF 4 Channel 4 2.2 HobbyKing RX 5 3. Instructions 3.1 Basic functions 6 3.2 Flashing

More information

MegaPoints Servo Controller

MegaPoints Servo Controller MegaPoints Servo Controller Covers Servo Controller boards 1.8 onwards A flexible and modular device for controlling model railway points and semaphore signals using inexpensive R/C servos and relays.

More information

User Instructions DSI 2008 Digital System Interface ADAM, ADAM CS, and Zeus Intercoms

User Instructions DSI 2008 Digital System Interface ADAM, ADAM CS, and Zeus Intercoms User Instructions DSI 2008 Digital System Interface ADAM, ADAM CS, and Zeus Intercoms 9350-7870-000 Rev C 11/2008 PROPRIETARY NOTICE The product information and design disclosed herein were originated

More information

HANDY DRIVE HANDHELD CONTROL SYSTEM TO DRIVE THE

HANDY DRIVE HANDHELD CONTROL SYSTEM TO DRIVE THE HANDY DRIVE HANDHELD CONTROL SYSTEM TO DRIVE THE CRAWLER TRACKS OF AN HYDRAULIC DRIVEN MACHINE The HandyDrive handheld control system, composed of the handeld remote control and the electronic control

More information

SYSMAC C200H-NC112 Position Control Unit

SYSMAC C200H-NC112 Position Control Unit Cat. No. W28-E-4 SYSMAC C2H-NC2 Position Control Unit C2H-NC2 Position Control Unit Operation Manual September 2 Notice: OMRON products are manufactured for use according to proper procedures by a qualified

More information

MBC Bipolar Microstep Driver. User s Guide E. Landon Drive Anaheim, CA

MBC Bipolar Microstep Driver. User s Guide E. Landon Drive Anaheim, CA MBC10641 Bipolar Microstep Driver User s Guide A N A H E I M A U T O M A T I O N 4985 E. Landon Drive Anaheim, CA 92807 e-mail: info@anaheimautomation.com (714) 992-6990 fax: (714) 992-0471 website: www.anaheimautomation.com

More information

3400HD Series TECHNICAL MANUAL X-3400HD DTI-3400HD D-3400HD. 3400HD Unwind (using 3400ce Circuit Board) Montalvo. Unwind Tension Controllers

3400HD Series TECHNICAL MANUAL X-3400HD DTI-3400HD D-3400HD. 3400HD Unwind (using 3400ce Circuit Board) Montalvo. Unwind Tension Controllers X-34HD DTI-34HD X-34ce (Circuit Board Version) DTI-34ce (Circuit Board Version) D-34HD D-34ce (Circuit Board Version) 34HD Unwind (using 34ce Circuit Board) PID Web Tension Controller Version 1. / Pub.

More information

ENCODING PHOTOCELLS MF6

ENCODING PHOTOCELLS MF6 ENCODING PHOTOCELLS MF6 Wall-mounted encoding photocells, 180 rotation and range of up to 20 mt. The code for the transmitted signal, which must be set at the time of installation, makes it possible to

More information