Blue Point Engineering

Size: px
Start display at page:

Download "Blue Point Engineering"

Transcription

1 DMX -Channel Relay Board Overview A two-channel DMX relay switch for switching loads up to 0A at 40V AC per channel. he DMX switch operates on the standard DMX5 bus and requires - DMX channels for operation. Relays can operate Independently or be set as Flip-Flop Relays he DMX address can be set between and 5. Setup Address / J Switches Connections he DMX Switch (-Ch Relay) board requires a V DC supply at 500 mamps. (via.mm socket, center pin positive or wire terminal block positive () and minus (-) connections.) Connect the relay board to the DMX network using 5-pin XLR connectors. (Input and Feed through) Connect the loads / devices to the relevant volt-free relay outputs -. ( See relay setup and application example pages for details). Each relay is rated at 0 Amps at 40V AC. Settings - (See Pages on Control / Addressing) Set the required base address using the DIP switches through 9. Add-up the values where the switch is set to the positions. he base address is read continuously. Set the base address of Relay No. as follows: Determine the start address value to be used for the DMX Ch Relay board. (See DMX Value table for values and switch setting) Switch the DIP switches for the address value selected to the position. : DIP switches 5 =(6) and 6=(3) set to position, the base address for the DMX Ch Relay board is now 6 3 = 48, this setting is used to determine the starting address output of the first Relay. Address 48 is the base address for Relay No.. he address of Relay No. is the base address of Relay plus for Relay. : Base = 49 (Relay No. ) Relay No is 49 ( 48 =49) Relay Control (JP switch setting (Byte) he relays on-board can be set as two different modes, by setting J switch or in the position. -Individual Relay Control J switch = normally relay mode, operates from -DMX channels with individual relay Relay- DMX CH- Value Relay- DMX CH- Value 4-55 = 4-55 = Status Status 3-0 = 3-0 = DMX CH Value Relay- Status Relay- Status Less than 80 Between 80 and 60 Greater than 60 DMX LED- when a suitable DMX signal is being received or a flashing LED when valid DMX signal stream is being received by the -Ch DMX relay board. Copyright 07 Blue Point, All Rights Reserved Blue Point Phone (303) (MS) Version WD564 -Relay Flip / Flop Relay Control J switch = relays are interconnected and operate from -DMX channel. (Relays Flip-Flop Mode)

2 DMX -Channel Relay Board Hook-up DMX -Ch Relay Board DMX- Board Address DIP Switches Power LED Optional Solid State Relay Setup OP VIEW Relay Contacts DMX-Network M XLR Connectors RELAY - RELAY - C- Common - Normal Open NC - Normal Closed C- Common - Normal Open NC - Normal Closed F DMX- Board Function DIP Switch J Normally relays J- Flip / Flop relays J- Relay- LED Relay- LED DMX- Board Address DIP Switches DMX- OK LED J DMX Switches ( Addressing ) Mechanical Relays Power Conection VDC 500 ma Wall Plug Power Supply 0.5 Amp Copyright 07 Blue Point, All Rights Reserved Blue Point Phone (303) (MS)

3 DMX -Channel Relay Board Relay Connection Mechanical Relays Relay - erminal Blocks Connection Relay Connections C- Common - Normal Open NC - Normal Closed Relay - - Normal Open C- Common Relay - LEDs Red Wall Power Supply ( Amp) () Red (-) Black LED-Bar ( Vdc) LED-Light Bars ( Vdc) - (-) () - Blue Point Copyright 07 Blue Point, All Rights Reserved Phone (303) (MS)

4 DMX -Channel Relay Board DMX Network Setup - 5 Pin Overview Software USB to DMX Interface USB Cable USB POR - OR - Computer - OR - USB Cable USB POR Control Software (VSA) Laptop Computer - OR - DMX Control Console 5-Pin (F) XLR Connector 5 Pin (F) to 5 Pin (M) DMX - XLR Cable Devices Connection s Power Supply Devices Relays X 8 * Connection s DMX- 8 Ch Relay Board RM Jumper (Last Device On Network) Relays X Power Supply 5-Pin (M) XLR Connector DMX- Ch Relay Board 5-Pin (F) XLR Connector 5-Pin (M) XLR Connector DMX - XLR Cable 5 Pin (F) to 5 Pin (M) Blue Point Copyright 07 Blue Point, All Rights Reserved Phone (303) (MS)

5 DMX -Channel Relay Board Board Address DMX - Values OP VIEW DIP Switches ( Addressing ) J= Blue Point 63 = Duo DMX (ch) Individual Relay Control DIP Switch 0 (J) = J= Individual Relay Control J Relay- Relay- (CH=49) (Value= 4-55) (Relay = ) (Value= 3-0) (Relay = ) Control Syntex - (See DMX5 Chart Chart for Values) J = (DIP Switch 0) set to : ( Multiple DMX control channels ) he output on a particular channel will go high () when the DMX transmitted value for that channel exceeds 4 and go low () when the DMX transmitted value for that channel is lower than 3. ( 3=, 0% and 4=, 00% ) DMX Value 0-55 = 0-00% (CH=48) (Value= 4-55) (Relay = ) (Value= 3-0) (Relay = ) Setting the base address of Relay Outputs (Switch 0 (J) set to ) Add the value of the address DIP switches set to the position to calculate the base address. (CH): DIP switches 5=(6) and 6=(3) set to position, the base address is now 48, (63) this setting is used to determine the starting address output of Relay, the next relay would be address 49 for Relay. () Individual Channel Relay Control DIp Switch 5 and 6 = Base start Address 48 = Relay No. J- Switch 0 = Relay at DMX value 4-55 RELAY - Relay at DMX value 3-0 Dip Sw 5 - Value =6 DIP Sw 6 - Value =3 Value= (63= 48 ) 48 = Start Address for Relay No. Relay No. = 49 ( Base address Relay No. = 48 = 49, Relay No. = 49 ) Relay at DMX value 4-55 RELAY - Relay at DMX value 3-0 Copyright 07 Blue Point, All Rights Reserved Blue Point Phone (303) (MS)

6 DMX -Channel Relay Board Board Address DMX - Values Base Address = 48 (Relay- Start = 48) Duo DMX (ch) Individual Relay Control DIP Switch 0 (J) = Individual Relay Control DMX Value-Channel - J= 0 = ( 0 %) 55 = ( 00 %) Relay- ( / ) (DMX Board Base Address = 48) (Relay = DMX Channel 48) (Relay = Value = 4-55) (Relay = Value = 3-0) J Switch = Relay- Status DMX CH- Value 4-55 = 3-0 = LED Status (CH- /) Single Channel Relay Control Base Address = 48 (Relay-) (Relay- = 48 = 49) J= DMX Value-Channel - 0 = ( 0 %) 55 = ( 00 %) Relay- (DMX Board Base Address = 48) ( / ) (Relay = DMX Channel 49) (Relay = Value = 4-55) (Relay = Value = 3-0) J Switch = Relay- Status LED Status (CH-) / DMX CH- Value 4-55 = 3-0 = Single Channel Relay Control Blue Point Copyright 07 Blue Point, All Rights Reserved Phone (303) (MS)

7 DMX -Channel Relay Board Board Address DMX - Values DIP Switches ( Addressing ) Blue Point Address = 48 Single DMX () Channel Control DIP Switch 0 (J) = Flip-Flop Relay Control Relay- () Relay- () DMX CH Data Value Relay Status Relay Status Less than 80 Flip Flip-Flop Function J Switch = (DMX Board Address = 48) (Value = 80-0) (Relay = ) (Relay = ) Flop J switch Relay- () Relay- () (DMX Board Address = 48) (Value = 80-60) (Relay = ) (Relay = ) DMX CH Data Value Relay Status Relay Status Between 80 and 60 Relay- () Relay- () (DMX Board Address = 48) (Value = 60-55) (Relay = ) (Relay = ) DMX CH Data Value Relay Status Relay Status Greater than 60 Flop Copyright 07 Blue Point, All Rights Reserved Blue Point Flip Phone (303) (MS)

8 DMX -Channel Relay Board Application Motor Set-up DUO Motors CW / CCW - OR - A B A B Rotation Change Switch A-B Switch B-A J SW- / Relay Functions Rotation CW Rotation CCW A B DMX Relay Board Rotation Volt DC Motor - A B C C - OR - Rotation Volt DC Motor - - Vdc Power Supply Blue Point Copyright 00 Blue Point, All Rights Reserved Phone (303) (MS)

9 DMX -Channel Relay Board Hybrid Application MP3 / Sound Board Playback Audio Amp & Speaker OPIAL PLAYBACK Speaker and Amplifier (Stereo Output) SD Card MP3 Player Board PLAYBACK - OR - Stereo Sound System MP3 Player Board Power SD Card MP3 Player No MP3 Player No Duo MP3 Player Board Ch- C - OR - C C Ch- MP3 Player Board Power DMX- -Ch Relay Audio MP3 Player No (Stereo Output) Audio MP3 Player No J switch Stereo Sound System Speaker and Amplifier Audio Amp & Speaker Copyright 07 Blue Point, All Rights Reserved Blue Point Phone (303) (MS)

10 DMX -Channel Relay Board DC MOOR Control- / Relay = Motor CW Rotation Relay Relay Relay Motor No. CCW Rotation CW Rotation Motor Logic Relay = Motor CCW Rotation Relay and and Com Com Volt DC Permanent Magnet Motor J switch = Motor All Stop DMX- -Ch Relay C C Relay- NC Relay- NC BLACK RED Relay MOOR POWER (Vdc) -Gnd V Relay J Flip-Flop Function SW- Air Supply 5/ Switching Solenoid Air Valve ( VDC) Air Hose Air Hose Air Hose Exhaust Ports Vdc - Vdc Vdc Vdc Power Supply Applications Relay Connection Pneumatic Setup J switch Pneumatic Cylinder (Double Acting) Copyright 07 Blue Point, All Rights Reserved C Blue Point Phone (303) (MS)

11 DMX -Channel Relay Board Notes / Work Sheet: DMX RELAY BOARD : DMX RELAY BOARD Application: Worksheet W Relay - Output Application Relay - J Single or Flip-Flop Function Addressing Copyright 07 Blue Point, All Rights Reserved J SW- SW- SW-3 SW-4 SW-5 SW-6 SW-7 SW-8 SW-9 SW-0 J Addressing Addressing = Relay 0 = Relay DMX Value Blue Point Phone (303) (MS)

12 DMX -Ch Relay Board to LW Inverter Relay Connection Mechanical Relays Relay - erminal Blocks Connection Relay Connections C- Common - Normal Open NC - Normal Closed Relay - - Normal Open C- Common Wall Power Supply ( Amp) LW INVERER POWER SUPPLY Red () Red (-) Black 50 FEE 50 FEE PD-00 Lightning Inverter CH- MAX. 00 FEE of LW Segments Combined per Inverter White s VDC Lightning Inverter Copyright 07 Blue Point, All Rights Reserved Blue Point Phone (303) (MS)

13 Lighting Segment Connections Lightning Lightning Segment Ch- MAX. 00 FEE OF Lightning Wall Power Adapter Vdc Power Supply (0 VAC to VDC) 00 FEE White s PD-00 Lightning Inverter CH- VDC Lightning Inverter Relay - Relay - Ch- (-) Com Com () Com- Common - Normal Open Wall Power Adapter Vdc Power Supply (0 VAC to VDC) () DMX -CH Relay Board White s Lightning Segment Ch- VDC Lightning Inverter Lightning Inverter CH- PD-00 (-) Lightning Segment Ch- 50 FEE MAX. 00 FEE of Lightning Segments 50 FEE Combined per Inverter Copyright 07 Blue Point, All Rights Reserved

14 DMX 5 Address Chart DMX -Channel Relay Board Reference Chart A - US Standard DMX 5 R Ch - Switches Ch - Switches Ch - Switches Ch - Switches Ch - Switches = = 3 =, 4 = 3 5 =, 3 6 =, 3 7 =,, 3 8 = 4 9 =, 4 0 =, 4 =,, 4 = 3, 4 3 =, 3, 4 4 =, 3, 4 5 =,, 3, 4 6 = 5 7 =, 5 8 =, 5 9 =,, 5 0 = 3, 5 =, 3, 5 =, 3, 5 3 =,, 3, 5 4 = 4, 5 5 =, 4, 5 6 =, 4, 5 7 =,, 4, 5 8 = 3, 4, 5 9 =, 3, 4, 5 30 =, 3, 4, 5 3 =,, 3, 4, 5 3 = 6 33 =, 6 34 =, 6 35 =,, 6 36 = 3, 6 37 =, 3, 6 38 =, 3, 6 39 =,, 3, 6 40 = 4, 6 4 =, 4, 6 4 =, 4, 6 43 =,, 4, 6 44 = 3, 4, 6, 45 =, 3, 4, 6 46 =, 3, 4, 6 47 =,, 3, 4, 6 48 = 5, 6 49 =, 5, 6 50 =, 5, 6 5 =,, 5, 6 5 = 3, 5, 6 53 =, 3, 5, 6 54 =, 3, 5, 6 55 =,, 3, 5, 6 56 = 4, 5, 6 57 =, 4, 5, 6 58 =, 4, 5, 6 59 =,, 4, 5, 6 60 = 3, 4, 5, 6 6 =, 3, 4, 5, 6 6 =, 3, 4, 5, 6 63 =,, 3, 4, 5, 6 64 = 7 65 =, 7 66 =, 7 67 =,, 7 68 = 3, 7 69 =, 3, 7 70 =, 3, 7 7 =,, 3, 7 7 = 4, 7 73 =, 4, 7 74 =, 4, 7 75 =,, 4, 7 76 = 3, 4, 7 77 =, 3, 4, 7 78 =, 3, 4, 7 79 =,, 3, 4, 7 80 = 5, 7 8 =, 5, 7 8 =, 5, 7 83 =,, 5, 7 84 = 3, 5, 7 85 =, 3, 5, 7 86 =, 3, 5, 7 87 =,, 3, 5, 7 88 = 4, 5, 7 89 =, 4, 5, 7 90 =, 4, 5, 7 9 =,, 4, 5, 7 9 = 3, 4, 5, 7 93 =, 3, 4, 5, 7 94 =, 3, 4, 5, 7 95 =,, 3, 4, 5, 7 96 = 6, 7 97 =, 6, 7 98 =, 6, 7 99 =,, 6, 7 00 = 3, 6, 7 0 =, 3, 6, 7 0 =, 3, 6, 7 03 =,, 3, 6, 7 04 = 4, 6, 7 05 =, 4, 6, 7 06 =, 4, 6, 7 07 =,, 4, 6, 7 08 = 3, 4, 6, 7 09 =, 3, 4, 6, 7 0 =, 3, 4, 6, 7 =,, 3, 4, 6, 7 = 5, 6, 7 3 =, 5, 6, 7 4 =, 5, 6, 7 5 =,, 5, 6, 7 6 = 3, 5, 6, 7 7 =, 3, 5, 6, 7 8 =, 3, 5, 6, 7 9 =,, 3, 5, 6, 7 0 = 4, 5, 6, 7 =, 4, 5, 6, 7 =, 4, 5, 6, 7 3 =,, 4, 5, 6, 7 4 = 3, 4, 5, 6, 7 5 =, 3, 4, 5, 6, 7 6 =, 3, 4, 5, 6, 7 7 =,, 3, 4, 5, 6, 7 8 = 8 9 =, 8 30 =, 8 3 =,, 8 3 = 3, 8 33 =, 3, 8 34 =, 3, 8 35 =,, 3, 8 36 = 4, 8 37 =, 4, 8 38 =, 4, 8 39 =,, 4, 8 40 = 3, 4, 8 4 =, 3, 4, 8 4 =, 3, 4, 8 43 =,, 3, 4, 8 44 = 5, 8 45 =, 5, 8 46 =, 5, 8 47 =,, 5, 8 48 = 3, 5, 8 49 =, 3, 5, 8 50 =, 3, 5, 8 5 =,, 3, 5, 8 5 = 4, 5, 8 53 =, 4, 5, 8 54 =, 4, 5, 8 55 =,, 4, 5, 8 56 = 3, 4, 5, 8 57 =, 3, 4, 5, 8 58 =, 3, 4, 5, 8 59 =,, 3, 4, 5, 8 60 = 6, 8 6 =, 6, 8 6 =, 6, 8 63 =,, 6, 8 64 = 3, 6, 8 65 =, 3, 6, 8 66 =, 3, 6, 8 67 =,, 3, 6, 8 68 = 4, 6, 8 69 =, 4, 6, 8 70 =, 4, 6, 8 7 =,, 4, 6, 8 7 = 3, 4, 6, 8 73 =, 3, 4, 6, 8 74 =, 3, 4, 6, 8 75 =,, 3, 4, 6, 8 76 = 5, 6, 8 77 =, 5, 6, 8 78 =, 5, 6, 8 79 =,, 5, 6, 8 80 = 3, 5, 6, 8 8 =, 3, 5, 6, 8 8 =, 3, 5, 6, 8 83 =,, 3, 5, 6, 8 84 = 4, 5, 6, 8 85 =, 4, 5, 6, 8 86 =, 4, 5, 6, 8 87 =,, 4, 5, 6, 8 88 = 3, 4, 5, 6, 8 89 =, 3, 4, 5, 6, 8 90 =, 3, 4, 5, 6, 8 9 =,, 3, 4, 5, 6, 8 9 = 7, 8 93 =, 7, 8, 94 =, 7, 8, 95 =,, 7, 8 96 = 3, 7, 8 97 =, 3, 7, 8 98 =, 3, 7, 8 99 =,, 3, 7, 8 00 = 4, 7, 8, 0 =, 4, 7, 8 0 =, 4, 7, 8 03 =,, 4, 7, 8 04 = 3, 4, 7, 8 05 =, 3, 4, 7, 8 06 =, 3, 4, 7, 8 07 =,, 3, 4, 7, 8 08 = 5, 7, 8 09 =, 5, 7, 8 0 =, 5, 7, 8 =,, 5, 7, 8 = 3, 5, 7, 8 3 =, 3, 5, 7, 8 4 =, 3, 5, 7, 8 5 =,, 3, 5, 7, 8 6 = 4, 5, 7, 8 7 =, 4, 5, 7, 8 8 =, 4, 5, 7, 8 9 =,, 4, 5, 7, 8 0 = 3, 4, 5, 7, 8 =, 3, 4, 5, 7, 8 =, 3, 4, 5, 7, 8 3 =,, 3, 4, 5, 7, 8 4 = 6, 7, 8 5 =, 6, 7, 8 6 =, 6, 7, 8 7 =,, 6, 7, 8 8 = 3, 6, 7, 8 9 =, 3, 6, 7, 8 30 =, 3, 6, 7, 8 3 =,, 3, 6, 7, 8 3 = 4, 6, 7, 8 33 =, 4, 6, 7, 8 34 =, 4, 6, 7, 8 35 =,, 4, 6, 7, 8 36 = 3, 4, 6, 7, 8 37 =, 3, 4, 6, 7, 8 38 =, 3, 4, 6, 7, 8 39 =,, 3, 4, 6, 7, 8 40 = 5, 6, 7, 8 4 =, 5, 6, 7, 8 4 =, 5, 6, 7, 8 43 =,, 5, 6, 7, 8 44 = 3, 5, 6, 7, 8 45 =, 3, 5, 6, 7, 8 46 =, 3, 5, 6, 7, 8 47 =,, 3, 5, 6, 7, 8 48 = 4, 5, 6, 7, 8 49 =, 4, 5, 6, 7, 8 50 =, 4, 5, 6, 7, 8 5 =,, 4, 5, 6, 7, 8 5 = 3, 4, 5, 6, 7, 8 53 =, 3, 4, 5, 6, 7, 8 54 =, 3, 4, 5, 6, 7, 8 55 =,, 3, 4, 5, 6, 7, 8 56 = 9 57 =, 9 58 =, 9 59 =,, 9 60 = 3, 9 Blue Point Phone (303) (MS)

15 DMX Address Chart Cont. Ch - Switches Ch - Switches Ch - Switches Ch - Switches Ch - Switches 6 =, 3, 9 6 =, 3, 9 63 =,, 3, 9 64 = 4, 9 65 =, 4, 9 66 =, 4, 9 67 =,, 4, 9 68 = 3, 4, 9 69 =, 3, 4, 9 70 =, 3, 4, 9 7 =,, 3, 4, 9 7 = 5, 9 73 =, 5, 9 74 =, 5, 9 75 =,, 5, 9 76 = 3, 5, 9 77 =, 3, 5, 9 78 =, 3, 5, 9 79 =,, 3, 5, 9 80 = 4, 5, 9 8 =, 4, 5, 9 8 =, 4, 5, 9 83 =,, 4, 5, 9 84 = 3, 4, 5, 9 85 =, 3, 4, 5, 9 86 =, 3, 4, 5, 9 87 =,, 3, 4, 5, 9 88 = 6, 9 89 =, 6, 9 90 =, 6, 9 9 =,, 6, 9 9 = 3, 6, 9 93 =, 3, 6, 9 94 =, 3, 6, 9 95 =,, 3, 6, 9 96 = 4, 6, 9 97 =, 4, 6, 9 98 =, 4, 6, 9 99 =,, 4, 6, = 3, 4, 6, 9 30 =, 3, 4, 6, 9 30 =, 3, 4, 6, =,, 3, 4, 6, = 5, 6, =, 5, 6, =, 5, 6, =,, 5, 6, = 3, 5, 6, =, 3, 5, 6, 9 30 =, 3, 5, 6, 9 3 =,, 3, 5, 6, 9 3 = 4, 5, 6, 9 33 =, 4, 5, 6, 9 34 =, 4, 5, 6, 9 35 =,, 4, 5, 6, 9 36 = 3, 4, 5, 6, 9 37 =, 3, 4, 5, 6, 9 38 =, 3, 4, 5, 6, 9 39 =,, 3, 4, 5, 6, 9 30 = 7, 9 3 =, 7, 9 3 =, 7, 9 33 =,, 7, 9 34 = 3, 7, 9 35 =, 3, 7, 9 36 =, 3, 7, 9 37 =,, 3, 7, 9 38 = 4, 7, 9 39 =, 4, 7, =, 4, 7, 9 33 =,, 4, 7, 9 33 = 3, 4, 7, =, 3, 4, 7, =, 3, 4, 7, =,, 3, 4, 7, = 5, 7, =, 5, 7, =, 5, 7, =,, 5, 7, = 3, 5, 7, 9 34 =, 3, 5, 7, 9 34 =, 3, 5, 7, =,, 3, 5, 7, = 4, 5, 7, =, 4, 5, 7, =, 4, 5, 7, =,, 4, 5, 7, = 3, 4, 5, 7, =, 3, 4, 5, 7, =, 3, 4, 5, 7, 9 35 =,, 3, 4, 5, 7, 9 35 = 6, 7, =, 6, 7, =, 6, 7, =,, 6, 7, = 3, 6, 7, =, 3, 6, 7, =, 3, 6, 7, =,, 3, 6, 7, = 4, 6, 7, 9 36 =, 4, 6, 7, 9 36 =, 4, 6, 7, =,, 4, 6, 7, = 3, 4, 6, 7, =, 3, 4, 6, 7, =, 3, 4, 6, 7, =,, 3, 4, 6, 7, = 5, 6, 7, =, 5, 6, 7, =, 5, 6, 7, 9 37 =,, 5, 6, 7, 9 37 = 3, 5, 6, 7, =, 3, 5, 6, 7, =, 3, 5, 6, 7, =,, 3, 5, 6, 7, = 4, 5, 6, 7, =, 4, 5, 6, 7, =, 4, 5, 6, 7, =,, 4, 5, 6, 7, = 3, 4, 5, 6, 7, 9 38 =, 3, 4, 5, 6, 7, 9 38 =, 3, 4, 5, 6, 7, =,, 3, 4, 5, 6, 7, = 8, =, 8, =, 8, =,, 8, = 3, 8, =, 3, 8, =, 3, 8, 9 39 =,, 3, 8, 9 39 = 4, 8, =, 4, 8, =, 4, 8, =,, 4, 8, = 3, 4, 8, =, 3, 4, 8, =, 3, 4, 8, =,, 3, 4, 8, = 5, 8, 9 40 =, 5, 8, 9 40 =, 5, 8, =,, 5, 8, = 3, 5, 8, =, 3, 5, 8, =, 3, 5, 8, =,, 3, 5, 8, = 4, 5, 8, =, 4, 5, 8, 9 40 =, 4, 5, 8, 9 4 =,, 4, 5, 8, 9 4 = 3, 4, 5, 8, 9 43 =, 3, 4, 5, 8, 9 44 =, 3, 4, 5, 8, 9 45 =,, 3, 4, 5, 8, 9 46 = 6, 8, 9 47 =, 6, 8, 9 48 =, 6, 8, 9 49 =,, 6, 8, 9 40 = 3, 6, 8, 9 4 =, 3, 6, 8, 9 4 =, 3, 6, 8, 9 43 =,, 3, 6, 8, 9 44 = 4, 6, 8, 9 45 =, 4, 6, 8, 9 46 =, 4, 6, 8, 9 47 =,, 4, 6, 8, 9 48 = 3, 4, 6, 8, 9 49 =, 3, 4, 6, 8, =, 3, 4, 6, 8, 9 43 =,, 3, 4, 6, 8, 9 43 = 5, 6, 8, =, 5, 6, 8, =, 5, 6, 8, =,, 5, 6, 8, = 3, 5, 6, 8, =, 3, 5, 6, 8, =, 3, 5, 6, 8, =,, 3, 5, 6, 8, = 4, 5, 6, 8, 9 44 =, 4, 5, 6, 8, 9 44 =, 4, 5, 6, 8, =,, 4, 5, 6, 8, = 3, 4, 5, 6, 8, =, 3, 4, 5, 6, 8, =, 3, 4, 5, 6, 8, =,, 3, 4, 5, 6, 8, = 7, 8, =, 7, 8, =, 7, 8, 9 45 =,, 7, 8, 9 45 = 3, 7, 8, =, 3, 7, 8, =, 3, 7, 8, =,, 3, 7, 8, = 4, 7, 8, =, 4, 7, 8, =, 4, 7, 8, =,, 4, 7, 8, = 3, 4, 7, 8, 9 46 =, 3, 4, 7, 8, 9 46 =, 3, 4, 7, 8, =,, 3, 4, 7, 8, = 5, 7, 8, =, 5, 7, 8, =, 5, 7, 8, =,, 5, 7, 8, = 3, 5, 7, 8, =, 3, 5, 7, 8, =, 3, 5, 7, 8, 9 47 =,, 3, 5, 7, 8, 9 47 = 4, 5, 7, 8, =, 4, 5, 7, 8, =, 4, 5, 7, 8, =,, 4, 5, 7, 8, = 3, 4, 5, 7, 8, =, 3, 4, 5, 7, 8, =, 3, 4, 5, 7, 8, =,, 3, 4, 5, 7, 8, = 6, 7, 8, 9 48 =, 6, 7, 8, 9 48 =, 6, 7, 8, =,, 6, 7, 8, = 3, 6, 7, 8, =, 3, 6, 7, 8, =, 3, 6, 7, 8, =,, 3, 6, 7, 8, = 4, 6, 7, 8, =, 4, 6, 7, 8, =, 4, 6, 7, 8, 9 49 =,, 4, 6, 7, 8, 9 49 = 3, 4, 6, 7, 8, =, 3, 4, 6, 7, 8, =, 3, 4, 6, 7, 8, =,, 3, 4, 6, 7, 8, = 5, 6, 7, 8, 9, 497 =, 5, 6, 7, 8, =, 5, 6, 7, 8, =,, 5, 6, 7, 8, = 3, 5, 6, 7, 8, 9 50 =, 3, 5, 6, 7, 8, 9 50 =, 3, 5, 6, 7, 8, =,, 3, 5, 6, 7, 8, = 4, 5, 6, 7, 8, 9 Copyright 00 Blue Point, All Rights Reserved 505 =, 4, 5, 6, 7, 8, =, 4, 5, 6, 7, 8, =,, 4, 5, 6, 7, 8, = 3, 4, 5, 6, 7, 8, =, 3, 4, 5, 6, 7, 8, 9 50 =, 3, 4, 5, 6, 7, 8, 9 5 =,, 3, 4, 5, 6, 7, 8, 9 5 = = 4 US Standard DMX 5 J- Single or Flip / Flop Relay Function DIP Switches ( Addressing ) J Address 4 J Switch Value Address = 4 Switch =, 3, 6, 8, 9 Switch Position ( or ) Switch Number

Blue Point Engineering

Blue Point Engineering Overview single channel DMX switch for switching loads up to 10 he DMX-switch operates on the standard DMX512 bus and requires 1 channel for operation. Version 1.1-2010 WD1558 he board ase ddress may be

More information

DMX Digital-Servo Board

DMX Digital-Servo Board Version 1.0 2012 WD197 Overview he DMX DigitalServo module is designed to provide 8 consecutive channels of output from a standard DMX protocol input signal. he outputs may be configured to be 5VDC digital

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering Instruction I www.bpesolutions.com Pointing the Way to Solutions! Animatronic Wizard - 3 Board (BPE No. WAC-0030) Version 3.0 2009 Controller Page 1 The Wizard 3 Board will record

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering Instruction I www.bpesolutions.com Pointing the Way to Solutions! Puppet - II+ Controller (BPE No. PCA-0001) Servo Position Adjustment EEPROM Digital Button Power 5 Vdc Playback

More information

Blue Point Engineering

Blue Point Engineering lue Point Engineering Wizard - I Interface oard http://www.pesolutions.com (303) 651.3794 Pointing the Way to Solutions! Talking / Eye Moving Skull Connectors pplication Examples 7805 Eyeball Jar nimatronic

More information

Blue Point Engineering

Blue Point Engineering Overview Blue Point Instruction Board 2-CH Boards, Terminal Block and Ribbon Cable I Type: RF Radio (315 MHz) 1-2 Channels (FCC Part 15 Compliant Components). Operating Voltage: 6-15 VDC @ 1 Amp (Wall

More information

Experiment#6: Speaker Control

Experiment#6: Speaker Control Experiment#6: Speaker Control I. Objectives 1. Describe the operation of the driving circuit for SP1 speaker. II. Circuit Description The circuit of speaker and driver is shown in figure# 1 below. The

More information

Contents. Warranty and Disclaimer 2 Introduction 3

Contents. Warranty and Disclaimer 2 Introduction 3 Contents Warranty and Disclaimer 2 Introduction 3 Physical Dimensions Board Layout 4 Usage Using the Relay board 5 Setting the start address 5 Configuration Jumper 6 Using the Relays 7 Using the DMX connectors

More information

Integrated Servo Motor UCS57

Integrated Servo Motor UCS57 Integrated Servo Motor Introduction is a new generation of high performance digital integrated servo drive motor, which is a series of low voltage AC servo products integrated with AC servo motor and drive

More information

Z44R. Multi-purpose Rack Mixer. Item ref: User Manual

Z44R. Multi-purpose Rack Mixer. Item ref: User Manual Z44R Multi-purpose Rack Mixer Item ref: 953.020 User Manual 2 balanced microphone inputs Lo-cut rumble filters 3-band EQ per Mic channel Switchable 48V phantom power 2 x A/B selectable stereo line inputs

More information

Blue Point Engineering Inc.

Blue Point Engineering Inc. Engineering Inc. ireless Radio Control of Puppets Setup Overview RF Control C Pointing the ay to Solutions! Hardware Setup Overview Page 1 Servo No.1 Servo No.2 Control Signal Line RX8ch1,2 Servo Board

More information

TI RigExpert. User s manual. USB Transceiver Interface

TI RigExpert. User s manual. USB Transceiver Interface TI-5000 RigExpert USB Transceiver Interface User s manual . Table of contents Introduction Operating the TI-5000 Front and rear panels Transceiver and computer connection Updating the firmware Annexes

More information

OWNER S MANUAL RAM12BT V2/ RAM15BT V2

OWNER S MANUAL RAM12BT V2/ RAM15BT V2 OWNER S MANUAL RAM12BT V2/ RAM15BT V2 Thank you for purchasing this Rockville RAM Bluetooth v2 pro audio speaker. When you re looking for a quick sound reinforcement solution, you don t want to be bogged

More information

FIRST Robotics Control System

FIRST Robotics Control System 2018/2019 FIRST Robotics Control System Team 236 1 (click on a component to go to its slide) 2 The Robot Powered solely by 12V battery RoboRIO- is the computer on the robot Controlled by Java code on the

More information

MODEL AF200A: FM, FM/SCA RECEIVER/MONITOR OPERATION MANUAL

MODEL AF200A: FM, FM/SCA RECEIVER/MONITOR OPERATION MANUAL MODEL AF200A: FM, FM/SCA RECEIVER/MONITOR OPERATION MANUAL THE AF200A IS AN FM AND FM/SCA PROFESSIONAL STYLE RECEIVER/ MONITOR. IT S MANY APPLICATIONS INCLUDE STATION MONITORING AND EAS MONITORING. The

More information

MBC Bipolar Microstep Driver. User s Guide E. Landon Drive Anaheim, CA

MBC Bipolar Microstep Driver. User s Guide E. Landon Drive Anaheim, CA MBC10641 Bipolar Microstep Driver User s Guide A N A H E I M A U T O M A T I O N 4985 E. Landon Drive Anaheim, CA 92807 e-mail: info@anaheimautomation.com (714) 992-6990 fax: (714) 992-0471 website: www.anaheimautomation.com

More information

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input Ndrive PWM Amplifiers/Drives Ndrive Series Digital Servo Amplifiers PWM Wide output power range from 10 A peak to 200 A peak at 320 VDC 2- or 3-phase AC line input or DC input CE approved and NRTL safety

More information

Analog Servo Drive 20A20

Analog Servo Drive 20A20 Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

Vidur Tube Pre-amplifier Owner s Manual (v1.1)

Vidur Tube Pre-amplifier Owner s Manual (v1.1) Vidur Tube Pre-amplifier Owner s Manual (v1.1) Index Front Input 1 Pad control knob Mojo control Mute button FX loop controls 2 FX button EQ controls... 3 EQ button Master Back Tuner out... 4 FX loop Line

More information

SPECIFICATION EP 1000/1500/2000 Series

SPECIFICATION EP 1000/1500/2000 Series UNINTERRUPTIBLE POWER SYSTEM SPECIFICATION EP 1000/1500/2000 Series Page 1 of 28 1.0 Revision Summary REVISION SECTION DESCRIPTION Formal Release Page 2 of 28 Table of Contents 1. Introduction. 4 2. Block

More information

Universal audio/midi interface USER MANUAL

Universal audio/midi interface USER MANUAL Universal audio/midi interface USER MANUAL Contents Table of Contents Contents 2 English 3 Safety information 3 irig Pro DUO 3 Register your irig Pro DUO 3 irig Pro DUO overview 4 Installation and setup

More information

S1 Programming Chart Program Description S1 Switch Positions. Constant ON High/Low Track, WR

S1 Programming Chart Program Description S1 Switch Positions. Constant ON High/Low Track, WR RODIX INC. FEEDER CUBE FC90 Plus Series ADVANCED FEATURES Optional software features of the 24490 / 2449 circuit boards OVERVIEW: The FC90 Plus Series of feeder controls are built around the circuit boards

More information

2007 MFJ ENTERPRISES, INC.

2007 MFJ ENTERPRISES, INC. Model MFJ-643 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551 VERSION

More information

B25A20FAC SERIES BRUSHLESS SERVO AMPLIFIERS Model: B25A20FAC 120VAC Single Supply Operation

B25A20FAC SERIES BRUSHLESS SERVO AMPLIFIERS Model: B25A20FAC 120VAC Single Supply Operation B25A20FAC Series B25A20FAC SERIES BRUSHLESS SERVO AMPLIFIERS Model: B25A20FAC 120VAC Single Supply Operation FEATURES: All connections on front of amplifier Surface-mount technology Small size, low cost,

More information

Analog Servo Drive 100A40

Analog Servo Drive 100A40 Description Power Range The 100A40 PWM servo drive is designed to drive brush type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected

More information

Blue Point Engineering

Blue Point Engineering DMX Data Analyzer Board nstruction Overview DMX Analyzer - Tester PC Board Design your own enclosure with an analyzer / tester display or add to your existing equipment or system. The DMX Analyzer is a

More information

USER S MANUAL. C41 VARIABLE SPEED CONTROL Rev. 2 User manual Rev. 1

USER S MANUAL. C41 VARIABLE SPEED CONTROL Rev. 2 User manual Rev. 1 USER S MANUAL C41 VARIABLE SPEED CONTROL Rev. 2 User manual Rev. 1 JUNE 2013 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 OVERVIEW... 2 2.0 FEATURES... 2 3.0 SPECIFICATIONS... 3 4.0 INSTALLATION

More information

8 Channel, DMX to 0 10 volt, Decoder board

8 Channel, DMX to 0 10 volt, Decoder board 8 Channel, DMX to 0 10 volt, Decoder board Allows DMX512 digital protocol to control analog devices that require a 0-10VDC control voltage. Upgrade 0-10 volt analog dimmers, use with motor controllers

More information

RT-21 Az-El Controller Manual addendum to RT-21 - August 5, 2014

RT-21 Az-El Controller Manual addendum to RT-21 - August 5, 2014 RT-21 Az-El Controller Manual addendum to RT-21 - August 5, 2014 Overview: The RT-21 Az-El controller consists of two RT-21 units with a shared power supply and shared chassis. The unit features a pair

More information

Your Hammond Sk-series keyboard is shipped from the factory set for 120 V.A.C. power. To connect the Sk-series keyboard to A.C.

Your Hammond Sk-series keyboard is shipped from the factory set for 120 V.A.C. power. To connect the Sk-series keyboard to A.C. -73-88 INTRODUCTION Introduction 1 INTRODUCTION Basic Hook-Up All connections are found on the Accessory Panel on the back of the Sk-series keyboard. A.C. Power Your Hammond Sk-series keyboard is shipped

More information

F O R T H E L O V E O F M U S I C SERIES 218 DPS200 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION

F O R T H E L O V E O F M U S I C SERIES 218 DPS200 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION F O R T H E L O V E O F M U S I C SERIES 218 DPS200 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION You have purchased an amplifier that leads the way with sound quality, reliability, and features.

More information

F O R T H E L O V E O F M U S I C LP100 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION

F O R T H E L O V E O F M U S I C LP100 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION F O R T H E L O V E O F M U S I C LP100 OWNER'S MANUAL AND INSTALLATION GUIDE INTRODUCTION You have purchased an amplifier that leads the way with sound quality, reliability, and features. These high performance

More information

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input

Ndrive Series. Digital Servo Amplifiers PWM. Wide output power range from 10 A peak to 200 A peak at 320 VDC. 2- or 3-phase AC line input or DC input Ndrive PWM Amplifiers/Drives Ndrive Series Digital Servo Amplifiers PWM Wide output power range from 10 A peak to 200 A peak at 320 VDC 2- or 3-phase AC line input or DC input CE approved and NRTL safety

More information

RELAY G10S PILOT S GUIDE B Yamaha Guitar Group, Inc. All rights reserved.

RELAY G10S PILOT S GUIDE B Yamaha Guitar Group, Inc. All rights reserved. RELAY G10S PILOT S GUIDE 40-00-0402 - B www.line6.com/manuals 2018 Yamaha Guitar Group, Inc. All rights reserved. System Overview Wireless freedom for your pedalboard Best in class sound quality provided

More information

Instruction Kit MIXER AMPLIFIER GT 60C GT 125C. GROMMES-PRECISION SINCE-46

Instruction Kit MIXER AMPLIFIER GT 60C GT 125C. GROMMES-PRECISION SINCE-46 Instruction Kit GT 60C GT 125C MIXER AMPLIFIER GROMMES-PRECISION 1-800-SINCE-46 www.grommesprecision.com Thank you for purchasing from Grommes~Precision! Grommes~Precision and its commercial audio division,

More information

CABINET POWERED MIXING CONSOLE

CABINET POWERED MIXING CONSOLE R SHS AUDIO SPMU- 00 CABINET POWERED MIXING CONSOLE USER'S MANUAL SAFETY INSTRUCTIONS SPECIFICATIONS Inputs Input modes Input Impedance Rated Input level Connector WARNING - TO REDUCE THE RISK OF FIRE

More information

Octasound RAMX2 V2.0 - Setting the Jumpers

Octasound RAMX2 V2.0 - Setting the Jumpers Octasound RMX2 V2.0 - Setting the Jumpers The first requirement for the RMX2 to work according to your installation is to set the jumpers according to the charts below. With the new version of the mixer

More information

APPLICATION NOTES CONNECTING A COLLABORATE ROOM TO A CONVERGE PRO. Purpose: Connecting the COLLABORATE Room to the CONVERGE Pro:

APPLICATION NOTES CONNECTING A COLLABORATE ROOM TO A CONVERGE PRO. Purpose: Connecting the COLLABORATE Room to the CONVERGE Pro: APPLICATION NOTES CLEARONE DOCUMENT 801-000-000-10 (REVISION 1.0) September, 2012 CONNECTING A COLLABORATE ROOM TO A CONVERGE PRO Purpose: This application note will describe the steps needed to interface

More information

Peak Current. Continuous Current. See Part Numbering Information on last page of datasheet for additional ordering options.

Peak Current. Continuous Current. See Part Numbering Information on last page of datasheet for additional ordering options. Description Power Range The PWM servo drive is designed to drive brushless DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected against

More information

Variable Gm Calibration Procedure

Variable Gm Calibration Procedure Variable Gm Calibration Procedure REV. 3 Sept. 16, 2018. Warm-up Power on the unit and let it warm for about 20-30 minutes, so that all circuitries stabilize. A.C. Check With a DMM (Digital Multi Meter)

More information

User Guide FFFA

User Guide FFFA User Guide FFFA001253 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 4 Box Contents...4 System Requirements....4

More information

Studio. PRO High Performance Professional Audio MODEL:PA105/PA205 PA AMPLIFIER

Studio. PRO High Performance Professional Audio MODEL:PA105/PA205 PA AMPLIFIER Studio PRO High Performance Professional Audio MODEL:PA105/PA205 PA AMPLIFIER INTRODUCTION Your New PYRAMID PA105/PA205 PA AMPLIFIER gives you the power and versatility you need in a professional sound

More information

BAND AIDE AUTOMATIC BAND DECODER

BAND AIDE AUTOMATIC BAND DECODER BAND AIDE AUTOMATIC BAND DECODER 1. Features Overview The Top Ten Devices Band Aide is an accessory that attaches to your radio (or computer), decodes the band data provided by the radio, and provides

More information

Crown CDi Amplifier Set-Up

Crown CDi Amplifier Set-Up Crown CDi Amplifier Set-Up For Origin Landscape Speakers Models: CDi1000 CDi2000 CDi4000 TABLE OF CONTENTS Introduction 2 Crown Amplifier Ins & Outs 2 Input Connections 2 Unbalanced (Most Common) 2 Balanced

More information

DigiSpeed DC-03. Isolated Control Voltage Generator User s Guide. PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84

DigiSpeed DC-03. Isolated Control Voltage Generator User s Guide. PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84 DigiSpeed DC-03 - Users Guide Page 1 Updated: 29. April 2009 DigiSpeed DC-03 Isolated Control Voltage Generator User s Guide PCB: DC-03 V3.0 Firmware: Ver: 3.0 Mach3: Ver: 1.84 DigiSpeed DC-03 - Users

More information

WTDIN-M. eeder. Digital Input Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies

WTDIN-M. eeder. Digital Input Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies eeder Technologies 90-A Beal Pkwy NW, Fort Walton Beach, FL 32548 www.weedtech.com 850-863-5723 Digital Input Module FEATURES 8 wide-range digital input channels with high voltage transient protection.

More information

Interface Genius Modem Instruction Manual v1.2.4

Interface Genius Modem Instruction Manual v1.2.4 Interface Genius Modem Instruction Manual v1.2.4 Interface Genius Modem is a USB / LAN controlled SO2R radio interface remote radio modem. It is designed to be controlled by a Windows application, and

More information

WTDOT-M. eeder. Digital Output Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies

WTDOT-M. eeder. Digital Output Module. Technologies FEATURES SPECIFICATIONS DESCRIPTION. Weeder Technologies eeder Technologies 90-A Beal Pkwy NW, Fort Walton Beach, FL 32548 www.weedtech.com 850-863-5723 Digital Output Module FEATURES 8 high-current open-collector output channels with automatic overload shutdown.

More information

Analog Servo Drive 30A20AC

Analog Servo Drive 30A20AC Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

HOOKING IT UP. Unpacking and Inspection. Installing in a Rack CHAPTER 3: Hooking It Up

HOOKING IT UP. Unpacking and Inspection. Installing in a Rack CHAPTER 3: Hooking It Up CHAPTER 3: HOOKING IT UP Unpacking and Inspection Your Studio 32 was packed carefully at the factory, and the container was designed to protect the unit during shipping. Please retain this container in

More information

NEW PRODUCT RANGE. Professional Audio & Lighting Cables. High Quality Nickel Plated REAN Connectors. Supplied on Hanging Cards

NEW PRODUCT RANGE. Professional Audio & Lighting Cables. High Quality Nickel Plated REAN Connectors. Supplied on Hanging Cards Professional Audio & Lighting Cables NEW PRODUCT RANGE CONNECTORS BY REAN a brand of Neutrik AG High Quality Nickel Plated REAN Connectors Supplied on Hanging Cards Clear Heatshrink for Identification

More information

DMX-K-DRV-17 Integrated Step Motor Driver & Basic Controller

DMX-K-DRV-17 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-17 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-17 Manual - 1 - rev 1.35 COPYRIGHT 2015 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.

More information

User Manual. MA 21 Two zone mixing amplifier

User Manual. MA 21 Two zone mixing amplifier User Manual MA 21 Two zone mixing amplifier Safety instructions When using this electronic device, basic precautions should always be taken, including the following: 1 Read all instructions before using

More information

Adjustable Parametric Equalizer Hardware Description

Adjustable Parametric Equalizer Hardware Description Adjustable Parametric Equalizer Hardware Description Adam Grunke April 27, 2004 ETEC 474 Professor Morton Introduction The Adjustable Parametric Equalizer (APE) allows the professional audio engineer to

More information

Mach3 USB Motion Card (STB5100) Installation Manual

Mach3 USB Motion Card (STB5100) Installation Manual Mach3 USB Motion Card (STB5100) Installation Manual V2.1 The motion control card for machine control, with strong professional. Requires the operator to have the relevant expertise! If used improperly,

More information

19'' Rack Mount 300 Watt Power Amplifier/ Mixer w/70v Output & Mic Talkover USER MANUAL

19'' Rack Mount 300 Watt Power Amplifier/ Mixer w/70v Output & Mic Talkover USER MANUAL 19'' Rack Mount 300 Watt Power Amplifier/ Mixer w/70v Output & Mic Talkover USER MANUAL Your new PYRAMID PA305 300 Watt P.A. Amplifier gives you the power and versatility you need in a professional sound

More information

Microprocessor Control Board Set Up Procedures (OR PLC)

Microprocessor Control Board Set Up Procedures (OR PLC) Microprocessor Control Board Set Up Procedures (OR-00 PLC) SWITCHES/PUSHBUTTONS Push Buttons at display SW Enter button SW Back button SW Down SW UP Back light on/off switch Rotary switches on main board

More information

HOMANN DESIGNS. DigiSpeed. Instruction manual. Version 1.0. Copyright 2004 Homann Designs.

HOMANN DESIGNS. DigiSpeed. Instruction manual. Version 1.0. Copyright 2004 Homann Designs. HOMANN DESIGNS DigiSpeed Instruction manual Version 1.0 Copyright 2004 Homann Designs http://www.homanndesigns.com Table of Contents Introduction...3 Features...3 DigiSpeed Operation Description...5 Overview...5

More information

DMX-K-DRV-23 Integrated Step Motor Driver & Basic Controller

DMX-K-DRV-23 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-23 Integrated Step Motor Driver & Basic Controller DMX-K-DRV-23 Manual - 1 - rev 1.35 COPYRIGHT 2013 ARCUS, ALL RIGHTS RESERVED First edition, June 2007 ARCUS TECHNOLOGY copyrights this document.

More information

CNC4PC. C19 A/C FREQUENCY CONVERTER Rev. 4

CNC4PC. C19 A/C FREQUENCY CONVERTER Rev. 4 CNC4PC Manual C19 A/C FREQUENCY CONVERTER Rev. 4 Overview This unit is an easy to use speed controller for routers. It work by modifying the output frequency according to an external control signal. It

More information

Analog Servo Drive 30A8

Analog Servo Drive 30A8 Description Power Range NOTE: This product has been replaced by the AxCent family of servo drives. Please visit our website at www.a-m-c.com or contact us for replacement model information and retrofit

More information

MP212 Principles of Audio Technology II

MP212 Principles of Audio Technology II MP212 Principles of Audio Technology II Lab #2 DM2000 and Pro Tools Version 3, 06/07/2012 revised AR, previous versions: JMC, JL Version 4, 09/15/2013 revised AR Copyright 2007 Berklee College of Music.

More information

NetBiter I/O Extender 4RO 6RTD 8DIO - DAIO User Manual Revision 1.00

NetBiter I/O Extender 4RO 6RTD 8DIO - DAIO User Manual Revision 1.00 NetBiter I/O Extender 4RO 6RTD 8DIO DAIO User Manual Revision 1.00 IntelliCom Innovation AB Linjegatan 3D SE302 50 Halmstad SWEDEN Phone +46 35 18 21 70 Fax +46 35 18 21 99 email info@intellicom.se www

More information

PARTY-LINE INTERCOM SYSTEM INSTALLATION MANUAL

PARTY-LINE INTERCOM SYSTEM INSTALLATION MANUAL PARTY-LINE INTERCOM SYSTEM INSTALLATION MANUAL TABLE OF CONTENTS Introduction... 1 The Clear-Com Concept... 1 Power Distribution and Short Circuit Protection... 2 Installing an Intercom System... Single-Channel

More information

RigExpert TI-7 USB Transceiver Interface User s manual

RigExpert TI-7 USB Transceiver Interface User s manual RigExpert TI-7 USB Transceiver Interface User s manual Please read this manual before attempting to use the RigExpert TI-7 device. - - 2 - Table of contents 1. What is a RigExpert TI-7?... 4 2. Specifications...

More information

Data Acquisition Modules/ Distributed IO Modules

Data Acquisition Modules/ Distributed IO Modules User Manual Data Acquisition Modules/ Distributed IO Modules Future Design Controls, Inc. 7524 West 98 th Place / P.O. Box 1196 Bridgeview, IL 60455 888.751.5444 - Office: 888.307.8014 - Fax 866.342.5332

More information

ELEC3106 Electronics. Lab 3: PCB EMI measurements. Objective. Components. Set-up

ELEC3106 Electronics. Lab 3: PCB EMI measurements. Objective. Components. Set-up ELEC3106 Electronics Lab 3: PCB EMI measurements Objective The objective of this laboratory session is to give the students a good understanding of critical PCB level Electromagnetic Interference phenomena

More information

Hardware Guide. Control Made Simple. Model 401A Signal Generator

Hardware Guide. Control Made Simple. Model 401A Signal Generator Control Made Simple Model 401A Signal Generator Hardware Guide ON OFF LIMIT 1 2 3 4 RXD TXD POWER West Coast Office 1263 El Camino Real Menlo Park, CA 94025 Phone (650) 853-1444 Fax (650) 853-1405 www.flashcutcnc.com

More information

Antenna Rotator System

Antenna Rotator System Antenna Rotator System Setup & Hardware Reference Manual RCI-SE August/2002 Rev 2.1a Introduction Thank you for purchasing the ARS interface. At the present day, the ARS is the more powerful, high performance

More information

Marchand Electronics Inc.

Marchand Electronics Inc. Marchand Electronics Inc. Rochester, NY. TEL:(585) 423 0462 www.marchandelec.com Electronic Crossover XM1 XM1 ELECTRONIC CROSSOVER NETWORK In many high performance loudspeaker systems the individual loudspeaker

More information

DXRL (DPM-RL) DMX RELAY DRIVER With optional 0-10 Volt Converter. ELM Video Technology, Inc. Innovative DMX and MIDI Products DESCRIPTION SETTINGS

DXRL (DPM-RL) DMX RELAY DRIVER With optional 0-10 Volt Converter. ELM Video Technology, Inc. Innovative DMX and MIDI Products DESCRIPTION SETTINGS .xx DESCRIPTIO The DXR (DPM-R) is a DMX to relay driver and controller, with an optional 0 to 10 volt converter. Control 12VDC relays up to 100mA each from any DMX console or any DMX generating device.

More information

C41 VARIABLE SPEED CONTROL Rev. 1.1

C41 VARIABLE SPEED CONTROL Rev. 1.1 C41 VARIABLE SPEED CONTROL Rev. 1.1 User manual Rev.1 1. Overview This card lets you control your spindle with PWM and direction signals, as if it was an axis motor. It converts the step signal into and

More information

Logosol AC Intelligent Servo Drive LS-182P for Panasonic A and S series motors

Logosol AC Intelligent Servo Drive LS-182P for Panasonic A and S series motors DESCRIPTION LS-182P is a version of LS-182, designed to work with Panasonic A or S series motors. For all standard features and parameters please refer to LS-182 manual. OREDERING GUIDE PART NUMBER MODEL

More information

Application Note #1245

Application Note #1245 Application Note #1245 ICM-1460-20W Interconnect Module with 20W Servo Drive The ICM-1460-20W (Rev D) Interconnect Module provides an on board 20W linear servo drive for the X-axis suitable for driving

More information

User Instructions DSI 2008 Digital System Interface ADAM, ADAM CS, and Zeus Intercoms

User Instructions DSI 2008 Digital System Interface ADAM, ADAM CS, and Zeus Intercoms User Instructions DSI 2008 Digital System Interface ADAM, ADAM CS, and Zeus Intercoms 9350-7870-000 Rev C 11/2008 PROPRIETARY NOTICE The product information and design disclosed herein were originated

More information

i3speakers LX503 MK2 User Manual

i3speakers LX503 MK2 User Manual i3speakers LX503 MK2 User Manual Index Introduction 5 Precautions 6 Safety requirements 6 Caution servicing 7 EC Declaration of Conformity 7 Waste of Electrical and Electronic Equipment (WEEE) 7 Chapter

More information

Continental Hydraulics Installation Manual CEM-RA-A

Continental Hydraulics Installation Manual CEM-RA-A CEM-RA-A Description: This ramp amplifier drives either single or dual solenoid proportional valve coils up to 2.6A. It is suitable to control current to either proportional directional, flow, or pressure

More information

CONCERT-1 CONCERT-2. Instrument DI. The World s Finest Transformers

CONCERT-1 CONCERT-2.  Instrument DI. The World s Finest Transformers Owner s Manual CONCERT-1 CONCERT-2 Instrument DI Jensen Transformers Inc 9304 Deering Ave. Chatsworth, CA 91311 Tel: 818-374-5857 Email: info@jensen-transformers.com www.jensen-transformers.com Concert-1

More information

Contents. Warranty and Disclaimer 2

Contents. Warranty and Disclaimer 2 Contents Warranty and Disclaimer 2 Physical Dimensions Board Layout 3 Usage Using the PWM board 4 Setting the start address 4 Dimming LED s 5,6 Typical hookup 7 Terminator 8 Troubleshooting Ground, termination,

More information

1. Connector Instruction: Trackball connection. (Figure 1, Game board instruction)

1. Connector Instruction: Trackball connection. (Figure 1, Game board instruction) Contents 1. Connector Instruction---------------------------------------1 2. Operation instruction---------------------------------------2 3. System Settings Configuration-------------------------------3

More information

Apogee Ensemble Thunderbolt Audio Interface

Apogee Ensemble Thunderbolt Audio Interface Apogee Ensemble Thunderbolt Audio Interface Quick Start Guide July 2017 Contents Overview... 3 Introduction...3 Package Contents...4 Ensemble Product Tour...6 Getting Started... 8 System Requirements...8

More information

Contents. Warranty and Disclaimer 2 Introduction 3

Contents. Warranty and Disclaimer 2 Introduction 3 Contents Warranty and Disclaimer 2 Introduction 3 Physical Dimensions Board Layout 4 Servo connections 5 Using the Serv8 Usage 6 Setting the start address 7 Setting the pulse width 8 Using the configuration

More information

CNC Router Parts CNC Router Parts 2.2 kw Plug and Play Spindle / VFD System CRP800 Set Up Guide

CNC Router Parts CNC Router Parts 2.2 kw Plug and Play Spindle / VFD System CRP800 Set Up Guide Step 1: Congratulations on your purchase of the 2.2 kw Plug and Play Spindle / VFD System! The first step in setting up your Spindle will be to physically connect your VFD to your CRP800 Control Unit with

More information

STEREO POWER AMPLIFIER OWNER MANUAL PR-150 DESIGNED IN U.K. PDF created with FinePrint pdffactory trial version

STEREO POWER AMPLIFIER OWNER MANUAL PR-150 DESIGNED IN U.K. PDF created with FinePrint pdffactory trial version STEREO POWER AMPLIFIER OWNER MANUAL PR-150 DESIGNED IN U.K. INTRODUCTION Congratulations on your purchase of MA PR-150 Stereo Power Amplifier. The performance of PR-150 is perfect for any audio application,

More information

PERMA Series Revision 2 Amplifiers

PERMA Series Revision 2 Amplifiers PERMA Series Revision 2 Amplifiers High Efficiency Life Safety Digital Power Amplifiers Current Thinking Document Number DDC PER 7001 02 ACS Introduction Voice Alarm (VA) systems are the quickest way to

More information

Ocean Controls KT-5221 Modbus IO Module

Ocean Controls KT-5221 Modbus IO Module Ocean Controls Modbus IO Module 8 Relay Outputs 4 Opto-Isolated Inputs 2 Analog Inputs (10 bit) 1 PWM Output (10 bit) 4 Input Counters Connections via Pluggable Screw Terminals 0-5V or 0-20mA Analog Inputs,

More information

BOSSCOM Powerlink 2-in-1

BOSSCOM Powerlink 2-in-1 BOSSCOM Powerlink 2-in-1 User manual Content Basic Applications... 3 Plug & Play... 3 Intallation... 4 Special Applications with an IR-receiver Connected... 5 Option Programming... 6 Specifications...

More information

IntelPage 5W (POCSAG) Transmitter

IntelPage 5W (POCSAG) Transmitter A division of NESS CORPORATION PTY LTD IntelPage 5W (POCSAG) Transmitter INSTALLATION MANUAL IntelPage 5W (POCSAG) Transmitter Installation Manual v1.2 1. Contents 1. Contents... 1 2. Equipment List...

More information

7.2 DV1311.L08 and DV1311.L12

7.2 DV1311.L08 and DV1311.L12 7. DV.L08 and DV.L 7.. General information The DV.L08 and DV.L modules let you control valve manifolds using multi-pin technology. There are two types of valve control modules available for delivery, which

More information

ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder)

ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder) ES86 Series Closed-loop Stepper Drive + Motor System (Drive+ Motor/Encoder) Traditional stepper motor drive systems operate open loop providing position control without feedback. However, because of this,

More information

3DM phase Digital Stepper Drive

3DM phase Digital Stepper Drive 3DM2283 3-phase Digital Stepper Drive 150-220VAC, 0.5-8.2A peak, Auto-configuration, Low Noise Anti-Resonance provides optimal torque and nulls mid-range instability Motor auto-identification and parameter

More information

PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide

PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide PROMUX Distributed MODBUS I/O Modules Catalog and Design Guide 14/11/2006 V10 P.O.Box 24 Stanfield 3613 SOUTH AFRICA Tel: +27 (031) 7028033 Fax: +27 (031) 7028041 Email: proconel@proconel.com Web: www.proconel.com

More information

Cross-Connect Interface

Cross-Connect Interface Cross-Connect Interface User Manual Document #: 050-015-0036R01 November 2006 TASC Systems Inc. Langley, BC Canada Cross-Connect System User Manual Preface This document describes the installation, commissioning

More information

Digital amplifier for proportional valves PEM XD

Digital amplifier for proportional valves PEM XD Digital amplifier for proportional valves PEM XD FEATURES - Amplifier for cap rail mounting according to DIN EN 50022 - Control of 2 coils in open loop, or 2 proportional valves with 1 coil in open loop

More information

Analog Servo Drive. Peak Current 16 A (11.3 A RMS )

Analog Servo Drive. Peak Current 16 A (11.3 A RMS ) Description The PWM servo drive is designed to drive three phase brushless motors with sine wave current at a high switching frequency. The drive requires two sinusoidal command signals with a 120-degree

More information

Interfacing Clockaudio microphones with the Logic Box

Interfacing Clockaudio microphones with the Logic Box Interfacing Clockaudio microphones with the INTRODUCTION One popular application for the is to interface with conferencing microphones that feature mute switches and LED indicators, and Clockaudio is a

More information

Sound Skulptor MC624 User manual

Sound Skulptor MC624 User manual Sound Skulptor MC624 User manual 1. Overview The MC624 lets you select one out of six stereo line level audio sources, adjust the level and route it to one out of four stereo amplified monitor pairs. The

More information

ZM 84 Audio Mixer. User Manual. Order code: CRAM41. Audio Mixer ZM 84 AUX 3 AUX 1 AUX 2 AUX 4 MASTER 1 MASTER 2 OFF BASS BASS TREBLE TREBLE BASS BASS

ZM 84 Audio Mixer. User Manual. Order code: CRAM41. Audio Mixer ZM 84 AUX 3 AUX 1 AUX 2 AUX 4 MASTER 1 MASTER 2 OFF BASS BASS TREBLE TREBLE BASS BASS ZM 84 Audio Mixer User Manual -20-10 0 +10 +20-20 -10 0 +10 +20 POWER L R 0 0 ON ZM 84 Audio Mixer AUX 4 MIC/LINE 1 MIC/LINE 1 MIC/LINE 2 MIC/LINE 3 MIC/LINE 4 THR THR +6 +10 +6 AUX 3 AUX 1 AUX 2 AUX 4

More information

AxCent Servo Drive A25A100

AxCent Servo Drive A25A100 Description Power Range The A25A100 PWM servo drive is designed to drive brush type DC motors at a high switching frequency. A single red/green LED indicates operating status. The drive is fully protected

More information

Maintenance Manual ERICSSONZ LBI-31552E

Maintenance Manual ERICSSONZ LBI-31552E E Maintenance Manual TONE REMOTE CONTROL BOARD 19A704686P4 (1-Frequency Transmit Receive with Channel Guard) 19A704686P6 (4-Frequency Transmit Receive with Channel Guard) ERICSSONZ Ericsson Inc. Private

More information