Deliverable D.5.3: Dissemination of Results in Scientific Publications and Peer-Reviewed Scientific Journals

Transcription

1 This project has received funding from the European Union s Seventh Framework Programme for research, technological development and demonstration under grant agreement no Accurate Simulations in Hydro-Machinery and Marine Propellers (ACCUSIM) Deliverable D.5.3: Dissemination of Results in Scientific Publications and Peer-Reviewed Scientific Journals Document identifier: ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Preparation date: 17/01/2018 Version: 01 State: Final Distribution: Public Issued : Aljaž Škerlavaj Verified : Dragica Jošt Approved : Enrico Nobile Call Identifier: FP7-PEOPLE-2013-IAPP Call Theme: Industry-Academia Partnerships and Pathways (IAPP) Contract start date: 01/02/2014 Duration: 48 months Project coordinator: Kolektor Turboinštitut Participating partner: University of Trieste Project website: ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 1 of 16

2 Document History Version Date Amended by Changes 01 17/01/2018 Aljaž Škerlavaj Document creation Contributors Both partners contributed and agreed with the content of this deliverable, which is the property of the ACCUSIM consortium. This document may be copied and reproduced. It may not be modified neither whole nor partially for any purpose without written permission from the ACCUSIM project coordinator with acceptance of the Project Consortium. ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 2 of 16

3 Executive Summary During the 48 months of the project (between February 2014 and end of January 2018), many dissemination and outreach activities were performed. This report presents dissemination of results in scientific publications and peer-reviewed scientific journals. All papers are included at the end of the report. Note In the correspondence (13/03/2017) with Project Officer Olivier Delaunoy it was accepted that this deliverable can be created in month 48 instead of in month 40 of the project. ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 3 of 16

4 Table of Contents 1 Introduction List of publications in scientific journals Scientific papers Strojniški vestnik (J. Mech. Eng) - article in press Francis-99 Workshop rd UIT Heat Transfer Conference CAV th UIT Heat Transfer Conference IAHR WG 2017 (Paper No. 1) IAHR WG 2017 (Paper No. 2) Conclusions ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 4 of 16

5 Abbreviations CFD mf KTI UniTS Computational Fluid Dynamics modefrontier (optimization software) Kolektor Turboinštitut University of Trieste ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 5 of 16

6 1 Introduction The ACCUSIM project aims to identify, develop and apply accurate, high-fidelity CFD approaches for the numerical predictions of the unsteady, turbulent and possibly cavitating flow in hydraulic turbines, pumps and marine propellers, and to develop advanced shape and functional optimization strategies for the best design of these systems. During the 48 months of the project (between February 2014 and end of January 2018), many dissemination and outreach activities were performed. This deliverable presents dissemination of results in scientific publications and peer-reviewed scientific journals. All papers are included at the end of the report. ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 6 of 16

7 2 List of publications in scientific journals The Table 1 is a list of all publications, where results of the ACCUSIM project were published either in scientific journal Strojniški vestnik (Journal of Mechanical Engineering) or presented at scientific conferences and then published in the online journal Journal of Physics: Conference Series. Other (scientific or not) conference publications are not included in this table or in this report. They are included only in the deliverable D.5.2, Dissemination of Results at National and International Conferences and Workshops. The paper that was accepted for publication in Journal of Mechanical Engineering is at the moment a paper in press, which means that it is not in the final form yet, although it is already accessible on the web pages of the journal. The first pages of each paper from the table are included in the next section of the report. Table 1: List of publications in scientific journals and in Journal of Physics: conference series. No. Title of paper or presentation 1. Jošt, D., Škerlavaj, A., Morgut, M., Mežnar, P., and Nobile, E., Numerical simulation of flow in a high head Francis turbine with prediction of efficiency, rotor stator interaction and vortex structures in the draft tube. Journal of Physics: Conference Series 579(1), doi: / /579/1/ (Workshop Francis-99, Trondheim, Norway, December 2014) 2. Morgut, M., Jošt, D., Nobile, E., and Škerlavaj, A., Numerical investigation of the flow in axial water turbines and marine propellers with scale-resolving simulations. Journal of Physics: Conference Series 655(1), doi: / /655/1/ (33rd UIT Heat Transfer Conference, L'Aquila, Italy, June 2015) 3. Morgut, M., Jošt, D., Nobile, E., and Škerlavaj, A., Numerical predictions of the turbulent cavitating flow around a marine propeller and an axial turbine. Journal of Physics: Conference Series 656(1), doi: / /656/1/ (9th International Symposium on Cavitation CAV2015, Lausanne, Switzerland, 6-10 December 2015.) 4. Škerlavaj, A., Morgut, M., Jošt, D., and Nobile, E., Optimization of a single-stage doublesuction centrifugal pump. Journal of Physics: Conference Series 796(1), doi: / /796/1/ (34th UIT Heat Transfer Conference, Ferrara, Italy, July 2016 ) 5. Jošt, D., Škerlavaj, A., Morgut, M., and Nobile, E., Numerical Prediction of Cavitating Vortex Rope in a Draft Tube of a Francis Turbine with Standard and Calibrated Cavitation Model. Journal of Physics: Conference Series 813(1), doi: / /813/1/ (7th IAHR International Meeting of the WorkGroup on Cavitation and Dynamic Problems in Hydraulic Machinery and Systems, Porto, Portugal, February 2017) 6. Škerlavaj, A., Morgut, M., Jošt, D., and Nobile, E., Decoupled CFD-based optimization of efficiency and cavitation performance of a double-suction pump. Journal of Physics: Conference Series 813(1), doi: / /813/1/ (7th IAHR International Meeting ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 7 of 16

8 No. Title of paper or presentation of the WorkGroup on Cavitation and Dynamic Problems in Hydraulic Machinery and Systems, Porto, Portugal, February 2017) 7. Morgut, M., Jošt, D., Škerlavaj, A., Nobile, E., and Contento, G Numerical Predictions of Cavitating Flow Around a Marine Propeller and Kaplan Turbine Runner with Calibrated Cavitation Models. J. of Mechanical Engineering, DOI: /sv-jme (accepted for publication) < ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 8 of 16

9 3 Scientific papers 3.1 Strojniški vestnik (J. Mech. Eng) - article in press ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 9 of 16

10 3.2 Francis-99 Workshop ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 10 of 16

11 3.3 33rd UIT Heat Transfer Conference ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 11 of 16

12 3.4 CAV2015 ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 12 of 16

13 3.5 34th UIT Heat Transfer Conference ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 13 of 16

14 3.6 IAHR WG 2017 (Paper No. 1) ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 14 of 16

15 3.7 IAHR WG 2017 (Paper No. 2) ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 15 of 16

16 4 Conclusions During the project the researchers focused on various types of dissemination activities. One of the most important types were presentations at professional conferences, such as the NAV (for naval architecture), IAHR (for hydraulic machines) and CAV (for cavitation). Papers presented at the IAHR and CAV conferences were published online, in the IOP Publishing journal. Therefore, this deliverable presents dissemination activities of the ACCUSIM project at publications in a scientific journal and IOP conference proceedings. Six papers were published by the IOP Publishing journal Journal of Physics: Conference Series, whereas one was accepted for publication in Strojniški vestnik (Journal of Mechanical Engineering). ACCUSIM_Dissemination_Journals_D.5.3_v01.doc Page 16 of 16