Brief Introduction to Engineering Graphics The use of drawings to convey information. Sketching freehand straight edge
|
|
- Andra Eleanore Cook
- 5 years ago
- Views:
Transcription
1 Brief Introduction to Engineering Graphics The use of drawings to convey information. Sketching freehand straight edge CAD drawings 2D drafting 3D model to 2D drawings 1 Different Graphical Representation of objects. On pg 27: See Fig. 3 and Table 1 Orthographics Multiviews Pictorials Isometric - a special type of axonometric which uses 120 degree angles for axis. Obliques-front faces similar to orthographic: 90 axis 120 Isometric 90 Oblique Perspectives Used in architecture, more realistic but hard to use for measuring. 2 Brief Introduction Lecture:F16 Handout Page 1
2 Information that is hard to read is even harder to understand use GOOD ENGINEERING LETTERING Class standard is VERTICAL and UPPERCASE (except in the case of *metric units) as shown on pg. 39 Fig. 21of graphics text Usually height of text is about 1/8 (3 mm) but don t measure it use guidelines if provided. Example of lettering expected for all class assignments. *Note: 25.4 mm = 1 INCH mm is millimeters, leave lowercase 10 mm = 1 centimeter mm IS THE STANDARD METRIC UNIT See pg. 30 Sec. 3 I inch Fractions can vary from standard don t make too small Engineering Lettering 3 Examples of Lettering Decent Lettering spaced a bit too close together Good Form plus correct way to do millimeters (case-sensitive) Same here needs to keep letters VERTICAL!!! FLOATING letters needs to use the guidelines Incorrect fraction (too small). POOR form (one shouldn t have top or bottom plus NON-UNIFORM height. 4 Brief Introduction Lecture:F16 Handout Page 2
3 Expectations of Lettering Good spacing of letterings could be improved upon Fair to Poor form is fine but not uniform height FLOATING letters. Poor to Fail Not vertical, not uniform height, poor spacing. 5 The type or appearance of a line depends on what it is trying to represent. Be familiar with the different types of lines found in Fig. 7 on pg. 29. Solid/Continuous indicates a visible surface/edge Dashed indicates a hidden surface/edge Centerline indicates symmetry Each linetype has its own lineweight too. - Linetypes - Centermark indicates center of circular feature. Extends past actual diameter Ø of circle of or radius of arc. Radius of: 22 mm Started at 10 mm mark - due to manufacture of ruler 6 Brief Introduction Lecture:F16 Handout Page 3
4 Use of straight edge is allowed. Lettering templates, circle templates, compasses and other drafting equipment is not allowed. NEATNESS and ACCURACY do count! Even Lineweight (LWT) Sharp corners Gaps (or no gaps) in important areas Examples will be given showing both good and poor work. - RULES and EXPECTATIONS - 7 GOOD (A work) FAIR (B work) Uneven LW Visible Lines need to be darker Poor dashes POOR (D work) overall neatness used straightedge (sort of) I suggest using a SHARP No. 2 pencil or a 0.7 mm HB lead mechanical pencil. Don t forget the straight edge. Fig. 24 on page 70 shows examples of good totally freehand lines. You are allowed and expected to use a straight edge. - SKETCHING EXAMPLES - 8 Brief Introduction Lecture:F16 Handout Page 4
5 Examples See Methods for sketching circles on page 73 for good circle sketching technique. FAIR circle sketch a bit too flatten bottom Circle form good uneven lineweight (LWT) Uneven LWT Didn t use straight edge 9 Hidden Lines should not be scaled Watch for where gaps should be Uneven linewt This is a better hidden line form. Poor hidden line form, this is a stitch. Circle is poor -More Examples- 10 Follow directions. Gaps should be included only when needed. Uneven linewt Brief Introduction Lecture:F16 Handout Page 5
6 Metric is millimeters 10 mm per centimeter 2.54 centimeter per inch Decimal Inch smallest unit is.02 inch 50 divisions within each inch 12 inches per foot - Decimal Inch and Metric Scale- 11 ABBREVIATIONS USED IN GRADING FOR REFERENCE LWT or LW for lineweight GEL for good engineering lettering ^ for gap needed (or not needed) NEAT for neatness ACC for accuracy WSS for where shape shows FFS from finished surface Brief Introduction Lecture:F16 Handout Page 6
7
Chapter 6. Architectural Lines and Lettering
Chapter 6 Architectural Lines and Lettering Drafting Introduction Universal graphic language Uses lines, symbols, dimensions, and notes to describe a structure to be built Properly drawn lines are dark,
Chapter 1 Overview of an Engineering Drawing
Chapter 1 Overview of an Engineering Drawing TOPICS Graphics language Engineering drawing Projection methods Orthographic projection Drawing standards TOPICS Traditional Drawing Tools Lettering Freehand
Reavis High School Curriculum Snapshot/Cover Page for Computer Aided Design (CAD)
Reavis High School Curriculum Snapshot/Cover Page for Computer Aided Design (CAD) Unit 1: Introduction In this unit, students will identify components of a Computer Aided Design (CAD) system and how to
Technology Education Grades Drafting I
Technology Education Grades 9-12 Drafting I 46 Grade Level: 9, 10, 11, 12 Technology Education, Grades 9-12 Drafting I Prerequisite: None Drafting I is an elective course which provides students the opportunity
Copyrighted Material. Copyrighted Material. Copyrighted. Copyrighted. Material
Engineering Graphics ORTHOGRAPHIC PROJECTION People who work with drawings develop the ability to look at lines on paper or on a computer screen and "see" the shapes of the objects the lines represent.
CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING. Prepared by: Sio Sreymean
CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING Prepared by: Sio Sreymean 2015-2016 Why do we need to study this subject? Effectiveness of Graphics Language 1. Try to write a description of this object. 2.
Fundamentals for building Drawing
Fundamentals for building Drawing What is Drawing Introduction Knowledge of preparing and understanding drawing will prove to be an invaluable aid while performing their jobs effectively, efficiently.
3. The dimensioning SYMBOLS for arcs and circles should be given:
Draft Student Name: Teacher: District: Date: Wake County Test: 9_12 T and I IC61 - Drafting I Test 2 Description: 4.08 Dimensioning Form: 501 1. The MINIMUM amount of space between two, ADJACENT DIMENSION
Chapter 8. Technical Drawings
Chapter 8 Technical Drawing Technical Drawings Multiview drawings Also called three-view drawings Simple objects take three views Front, top, one side Title block Identifies who did the design Gives date,
ORTHOGRAPHIC PROJECTION
ORTHOGRAPHIC PROJECTION C H A P T E R S I X OBJECTIVES 1. Recognize and the symbol for third-angle projection. 2. List the six principal views of projection. 3. Understand which views show depth in a drawing
MISS. HANNA S CLASSROOM RULES
MISS. HANNA S CLASSROOM RULES 1. My students never fail. I believe in you and so shall you! Miss. Hanna s Quote! 2. Come to class on time. 3. Bring a positive attitude. 4. Come prepared and bring your
Chapter 1 Overview of a Technical Drawing
Chapter 1 Overview of a Technical Drawing TOPICS Graphics language Engineering drawing Projection methods Orthographic projection Drawing standards TOPICS Traditional Drawing Tools Lettering Dimensioning
11/12/2015 CHAPTER 7. Axonometric Drawings (cont.) Axonometric Drawings (cont.) Isometric Projections (cont.) 1) Axonometric Drawings
CHAPTER 7 1) Axonometric Drawings 1) Introduction Isometric & Oblique Projection Axonometric projection is a parallel projection technique used to create a pictorial drawing of an object by rotating the
ENGINEERING GRAPHICS 1E9
Lecture 3 Monday, 15 December 2014 1 ENGINEERING GRAPHICS 1E9 Lecture 3: Isometric Projections Lecture 3 Monday, 15 December 2014 2 What is ISOMETRIC? It is a method of producing pictorial view of an object
Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 1. Description: Unit C - Sketching - Test 2.
Student Name: Teacher: Date: District: Rowan Assessment: 9_12 T and I IC61 - Drafting I Test 1 Description: Unit C - Sketching - Test 2 Form: 501 1. The most often used combination of views includes the:
Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 2. Description: Drafting 1 - Test 6.
Student Name: Teacher: Date: District: Rowan Assessment: 9_12 T and I IC61 - Drafting I Test 2 Description: Drafting 1 - Test 6 Form: 501 1. 2X on a hole note means: A. Double the size of the hole. B.
Technical Drawing 101 with AutoCAD 2018
Technical Drawing 101 with AutoCAD 2018 A Multidisciplinary Guide to Drafting Theory and Practice with Video Instruction Douglas Smith Antonio Ramirez Ashleigh Fuller SDC PUBLICATIONS Better Textbooks.
technical drawing
technical drawing school of art, design and architecture nust spring 2011 http://www.youtube.com/watch?v=q6mk9hpxwvo http://www.youtube.com/watch?v=bnu2gb7w4qs Objective abstraction - axonometric view
Technological Design Mr. Wadowski. Orthographic & Isometric Drawing Lesson
Technological Design Mr. Wadowski Orthographic & Isometric Drawing Lesson TOPICS Working Drawings, Isometric Drawings & Orthographic Drawings Glass box concept Multiview projection Orthographic projection
AutoCAD 2D-I. Module 1: Introduction to Drawing Tools. IAT Curriculum Unit PREPARED BY. January 2011
AutoCAD 2D-I Module 1: Introduction to Drawing Tools PREPARED BY IAT Curriculum Unit January 2011 Institute of Applied Technology, 2011 Module 1: Introduction to Drawing Tools Module Objectives After
CLASS views from detail on a grid paper. (use appropriate line types to show features) - Optional views. Turn in for grading on class 6 (06/04)
CLASS 4 Review: - Projections - Orthographic projections Lab: - 3 views from detail on a grid paper. (use appropriate line types to show features) - Optional views. Turn in for grading on class 6 (06/04)
Interpretation of Drawings. An Introduction to the Basic Concepts of Creating Technical Drawings
Interpretation of Drawings An Introduction to the Basic Concepts of Creating Technical Drawings Introduction In the design process drawings are the main way in which information about an object or product
DMT113 Engineering Drawing. Chapter 3 Stretch System
DMT113 Engineering Drawing Chapter 3 Stretch System Contents Theory & Multiview Planes 6 Principle Views Multiview Sketching Technique & Perspective First & Third Angle Multiview Representations Theory
Multi-View Drawing Review
Multi-View Drawing Review Sacramento City College EDT 300/ENGR 306 EDT 300 / ENGR 306 - Chapter 5 1 Objectives Identify and select the various views of an object. Determine the number of views needed to
Orthographic Drawing (Architectural Board Drafting)
Design and Drafting Description In this activity, the teacher will introduce orthographic projection, in which a multi-view drawing shows how the sides of an object are related to each another. Students
AutoCAD 2D I. Module 16. Isometric and Dimensioning. IAT Curriculum Unit PREPARED BY. January 2011
AutoCAD 2D I Module 16 Isometric and Dimensioning PREPARED BY IAT Curriculum Unit January 2011 Institute of Applied Technology, 2011 Module 16 Auto CAD Self-paced Learning Modules AutoCAD 2D Isometric
ENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems
Spring Semester 2016 ENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems Disclaimer Problems in this study guide resemble problems relating mainly to the pertinent homework assignments.
Engineering Drawing Lecture 5 PROJECTION THEORY
University of Palestine College of Engineering & Urban Planning First Level Engineering Drawing Lecture 5 PROJECTION THEORY Lecturer: Eng. Eman Al.Swaity Eng.Heba hamad PART 1 PROJECTION METHOD TOPICS
Lecture #4 MULTIVIEW PROJECTION RES 112E COMPUTER AIDED TECHNICAL DRAWING ITU
Lecture #4 MULTIVIEW PROJECTION This week You will learn multi-view projection. The steps to follow are: Projections (ISO-E & ISO-A) Multi-view drawings Views (Basic,Auxiliary, Detailed etc.) Sketching
COURSE: INTRODUCTION TO CAD GRADES: UNIT: Measurement
UNIT: Measurement - Students will demonstrate correctness in measuring using various scales and instruments. Demonstrate the various marks that make up a ruler including 1/16, 1/8, ¼ and ½. Assessment
ORTHOGRAPHIC PROJECTIONS. Ms. Sicola
ORTHOGRAPHIC PROJECTIONS Ms. Sicola Objectives List the six principal views of projection Sketch the top, front and right-side views of an object with normal, inclined, and oblique surfaces Objectives
Describing an Angle Bracket
Basics of Drafting Describing an Angle Bracket Orthographic Projection Orthographic drawings represent three dimensional objects in three separate views arranged in a standard manner. Orthographic Views
Chapter 1 Introduction
Chapter 1 Introduction Contents Engineering drawing Drawing standards Drawing sheet Scale Lettering Line types Engineering Drawing Contents Engineering Drawing Effectiveness of Graphic Language 1. Try
(As per New Revised Syllabus of Anna University) Department of Mechanical Engineering. SATHYABAMA UNIVERSITY Jeppiaar Nagar, Chennai
(1*,1((5,1* *5$3+,&6 (As per New Revised Syllabus of Anna University) Dr. S.RAMACHANDRAN, M.E., Ph.D. Professor & Head K. PANDIAN, M.E., E.V.V.RAMANAMURTHY, M.Tech., R. DEVARAJ, M.E., Associate Professors
1: Assemblage & Hierarchy
What: 1: Assemblage & Hierarchy 2 compositional sequences o abstract, line compositions based on a 9 square grid o one symmetrical o one asymmetrical Step 1: Collage Step 2: Additional lines Step 3: Hierarchy
ENGR 1182 Midterm Exam 1: Study Guide and Practice Problems
ENGR 1182 Midterm Exam 1: Study Guide and Practice Problems Disclaimer Problems seen in this study guide may resemble problems relating mainly to the pertinent homework assignments. Reading this study
GOAL Practise techniques for creating various types of geometric lines by constructing and reproducing figures. sheet of letter-sized white paper
TECHNIQUE STUDENT BOOK Chapter 11, page 340 TOOLBOX Pages 62 67 GOAL Practise techniques for creating various types of geometric lines by constructing and reproducing figures. MATERIALS drawing board T-square
DUE DATE: Friday 4/6/2018 at 3:30 PM
MECH 130 SPRING 2018 CAD LAB 4 FINAL REVISION HARDCOPIES NEEDED DUE DATE: Friday 4/6/2018 at 3:30 PM After the revised hitch, the ball and the pin parts were created from the Handout call LAB4 PART Creation,
Fundamentals of Drafting - Orthographic Projection with Hidden Details
Fundamentals of Drafting - Orthographic Projection with Hidden Details Objectives: 1. To extend the principle of orthographic projection for hidden details. 2. To illustrate the representation of hidden
How to Design a Geometric Stained Glass Lamp Shade
This technique requires no calculation tables, math, or angle computation. Instead you can use paper & pencil with basic tech drawing skills to design any size or shape spherical lamp with any number of
ENGINEERING DRAWING. 1. Set squares are used to draw different angles. What is the angel a formed by the 45⁰ set square? Give a brief answer.
ENGINEERING DRAWING 1. Set squares are used to draw different angles. What is the angel a formed by the 45⁰ set square? Give a brief answer. 2. Which is the correct method of hatching a plane surface?
Beginning Engineering Graphics 3 rd Week Lecture Notes Instructor: Edward N. Locke Topic: The Coordinate System, Types of Drawings and Orthographic
Beginning Engineering Graphics 3 rd Week Lecture Notes Instructor: Edward N. Locke Topic: The Coordinate System, Types of Drawings and Orthographic 1 st Subject: The Cartesian Coordinate System The Cartesian
Orthographic Projection
Orthographic Projection Why Orthographic Projection is used in technical drawing Orthographic projection is a method of producing a number of separate two-dimensional inter-related views, which are mutually
2012 Academic Challenge
2012 Academic Challenge ENGINEERING GRAPHICS TEST STATE FINAL This Test Consists of 40 Questions Engineering Graphics Test Production Team Ryan Brown, Illinois State University Author/Team Leader Jacob
DFTG-1305 Technical Drafting Prof. Francis Ha
DFTG-1305 Technical Drafting Prof. Francis Ha Session 5 Dimensioning Geisecke s textbook: 14 th Ed. Chapter 10 p. 362 15 th Ed. Chapter 11 p. 502 Update: 17-0508 Dimensioning Part 1 of 2 Dimensioning Summary
Engineering Working Drawings Basics
Engineering Working Drawings Basics Engineering graphics is an effective way of communicating technical ideas and it is an essential tool in engineering design where most of the design process is graphically
Graphical Communication
Chapter 9 Graphical Communication mmm Becoming a fully competent engineer is a long yet rewarding process that requires the acquisition of many diverse skills and a wide body of knowledge. Learning most
Multiview Projection
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Multiview Projection (or Orthographic Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 17-0510
Multiview Drawing. Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views.
Multiview Drawing Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views. Multiview Drawing Another name for multiview drawing is orthographic
UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS
UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS 5.1 Introduction Orthographic views are 2D images of a 3D object obtained by viewing it from different orthogonal directions. Six principal views are possible
A Concise Introduction to Engineering Graphics
A Concise Introduction to Engineering Graphics Fourth Edition Including Worksheet Series A Timothy J. Sexton, Professor Department of Industrial Technology Ohio University BONUS Book on CD: TECHNICAL GRAPHICS
TECHNICAL DESIGN I (540)
DESCRIPTION The first assessment in a series, Technical Design I prepares students to develop technical knowledge and skills required to plan and prepare scale pictorial interpretations of engineering
Chapter 5 Pictorial sketching
Chapter 5 Pictorial sketching Contents Freehand sketching techniques Pictorial projections - Axonometric - Oblique Isometric projection vs isometric sketch Isometric sketch from an orthographic views Isometric
Technical Graphics Higher Level
Coimisiún na Scrúduithe Stáit State Examinations Commission Junior Certificate Examination 2005 Technical Graphics Higher Level Marking Scheme Sections A and B Section A Q1. 12 Four diagrams, 3 marks for
Chapter 5 Pictorial Projection
Chapter 5 Pictorial Projection Objectives After completing this chapter, the students will be able to Create freehand sketches using the correct sketching techniques. Explainthe difference between axonometric
Dimensioning with SolidWorks - Demo
Dimensioning with SolidWorks - Demo Although most demos are implemented with word documents, this demo employs slides so that more details can be shown to the students as the drawing is constructed. Part
DFTG 1305 UNIT 1. Semester: Spring 2016 Class #: Term: SS Instructor: Mays ALSabbagh
DFTG 1305 UNIT 1 Semester: Spring 2016 Class #: 94412 Term: SS Instructor: Mays ALSabbagh Technical Drafting Unit One: Introduction to Drafting Chapter 1 : The World Wide Graphic language for Design Lecture
Orthographic Drawings
Orthographic Drawings You don t have to be an artist to draw great furniture plans. By Craig Bentzley W oodworking requires a graphic language to convey building information. We can t do it without drawings
CE 100 Civil Engineering Drawing Sessional (Lab Manual)
CE 100 Civil Engineering Drawing Sessional (Lab Manual) Department of Civil Engineering Ahsanullah University of Science and Technology November, 2017 1 Preface This course is designed to provide civil
2. Line composed of closely and evenly spaced short dashes in a drawing represents
1. Hidden lines are drawn as (a) dashed narrow lines (b) dashed wide lines (c) long-dashed dotted wide line (d) long-dashed double dotted wide line Ans: (a) 2. Line composed of closely and evenly spaced
At the conclusion of this unit you should be able to accomplish the following with a 70% accuracy
7 Multiview Drawing OBJECTIVES At the conclusion of this unit you should be able to accomplish the following with a 70% accuracy 1. explain the importance of mulitview drawing as a communication tool far
Two-Dimensional Drawing
22 Chapter Cxxxx 40757 3/19/08 10:24 AM Page 1 7% 3% 3% 18% 20% 22 Chapter CXXXX 40757 Page 1 03/18/08 MD 22 Two-Dimensional Drawing objectives After completing this chapter, you should be able to Identify
Scale and Dimensioning (Architectural Board Drafting)
Youth Explore Trades Skills Description In this activity, the teacher will first select an object that is larger than the page and scale it to fit in the designated drawing area to explain architectural
LECTURE 1 INRTRODUCTION TO CIVIL ENGINEERING DRAWING. Engr. Ali Raza Khalid Civil Engineering drawing
LECTURE 1 INRTRODUCTION TO CIVIL ENGINEERING DRAWING Engr. Ali Raza Khalid CIVIL ENGINEERING DRAWING COURSE OUTLINE Credit Hours: 2+2= 4 Introduction: Introduction to the subject and drawing equipment.
2004 Academic Challenge
2004 Academic Challenge ENGINEERING GRAPHICS TEST - REGIONAL Engineering Graphics Test Production Team Ryan Brown, Illinois State University Author/Team Coordinator Kevin Devine, Illinois State University
GUIDELINES FOR DRAFTING
UNIT 1 GUIDELINES FOR DRAFTING 1.1 Introduction The term draughting is used to describe the language of drafting in this book. It defines the terminology, symbology, conventions, and standards used in
AABTKJX by Prentice Hall, Inc. A Pearson Company
Figure Number: 03-01 Page Number: Principal Items of Equipment. AABTKJX0 Figure Number: 03-02 Page Number: The T-square. AABTKJY0 Figure Number: 03-03 Page Number: Testing the Working Edge of the Drawing
Dimensioning in the figure below could be improved by: A
1-Multiview-study Page 1 of 8 irections For Numbers 1-53 : Read each of the following multiple-choice items and the possible answers carefully. Mark the letter of the correct answer on your answer sheet
Page 1 of 5. ENGINEERING SKETCHES INFORMATION SHEETS MEL02INF2430 v1.1 HEALTH & SAFETY REQUIREMENTS
Page 1 of 5 Competenz - N Z Engineering Food & Manufacturing Industry Training Organisation Inc. ENGINEERING SKETCHES INFORMATION SHEETS MEL02INF2430 v1.1 HEALTH & SAFETY REQUIREMENTS RECORDING REQUIREMENTS:
Test Code: 8294 / Version 1
Pennsylvania Customized Assessment Blueprint Test Code: 8294 / Version 1 Copyright 2014. All Rights Reserved. General Assessment Information Blueprint Contents General Assessment Information Written Assessment
ME1105 Engineering Drawing & Design
City University London Term 1 Assessment 2008/2009 School of Engineering and Mathematical Sciences ME1105 Engineering Drawing & Design Student Name:.., Group: Examination duration: Reading time: This paper
Engineering Graphics. Class 2 Drafting Instruments Mohammad Kilani
Engineering Graphics Class 2 Drafting Instruments Mohammad Kilani Drafting Instruments A Design is as good as its instruments A engineering drawing is a highly stylized graphic representation of an idea.
Civil Engineering Drawing
Civil Engineering Drawing Third Angle Projection In third angle projection, front view is always drawn at the bottom, top view just above the front view, and end view, is drawn on that side of the front
DFTG-1305 Technical Drafting Prof. Francis Ha
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Orthographic Projection (or Multiview Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 18-0205
Dimensioning the Rectangular Problem
C h a p t e r 3 Dimensioning the Rectangular Problem In this chapter, you will learn the following to World Class standards: 1. Creating new layers in an AutoCAD drawing 2. Placing Centerlines on the drawing
Introduction to Drafting Design
Introduction to Drafting Design Unit: 1 Content Standard(s) and Orientation 1. Relate the importance of drafting design technology in today s technological work force. Learning Objective(s) and Essential
(Ans:d) a. A0 b. A1 c. A2 d. A3. (Ans:b) (Ans:a) (Ans:d) (Ans:d)
Multiple Choice Questions (MCQ) on Engineering Drawing (Instruments) The mini drafter serves the purpose of everything except a. Scales b. Set square c. Protractor d. Compass (Ans:d) During operation,
FACTFILE: GCE TECHNOLOGY & DESIGN
FACTFILE: GCE TECHNOLOGY & DESIGN 1.8, 1.26, 1.56 DESIGN AND COMMUNICATION Design and Communication Learning outcomes Students should be able to: communicate designs using 2D methods, to include freehand
Initial Template Setup
Initial Template Setup Template Development Objectives You will complete the following tasks during this stage of template development: Determine and set plot style behavior. Save mechanical, architectural,
Pictorial Drawings. DFTG-1305 Technical Drafting Prepared by Francis Ha, Instructor
DFTG-1305 Technical Drafting Prepared by Francis Ha, Instructor Pictorial Drawings Geisecke s textbook for reference: 14 th Ed. Ch. 15: p. 601 Ch. 16: p. 620 15 th Ed. Ch. 14: p. 518 Ch. 15: p. 552 Update:
Isometric Drawing Chapter 26
Isometric Drawing Chapter 26 Sacramento City College EDT 310 EDT 310 - Chapter 26 - Isometric Drawing 1 Drawing Types Pictorial Drawing types: Perspective Orthographic Isometric Oblique Pictorial - like
2010 Academic Challenge
2010 Academic Challenge ENGINEERING GRAPHICS TEST STATE FINALS This Test Consists of 40 Questions Engineering Graphics Test Production Team Ryan K. Brown, Illinois State University Author/Team Leader Jacob
1 st Subject: Types and Conventions of Dimensions and Notes
Beginning Engineering Graphics 7 th Week Lecture Notes Instructor: Edward N. Locke Topic: Dimensions, Tolerances, Graphs and Charts 1 st Subject: Types and Conventions of Dimensions and Notes A. Definitions
Chapter 2: Dimensioning Basic Topics Advanced Topics Exercises
Chapter 2: Dimensioning Basic Topics Advanced Topics Exercises Dimensioning: Basic Topics Summary 2-1) Detailed Drawings 2-2) Learning to Dimension 2-3) Dimension Appearance and Techniques. 2-4) Dimensioning
EL DORADO UNION HIGH SCHOOL DISTRICT Educational Services. Course of Study Information Page
Course of Study Information Page Course Title: Engineering Design and Architecture I (#0517)(Formerly Drafting 1 #0510) Rationale: This course in Engineering Design will introduce students to the fundamentals
UNIT Lines and Symbols
3 UNIT Lines and Symbols Various lines on a drawing have different meanings. They may appear solid, broken, thick, or thin. Each is designed to help the blueprint reader make an interpretation. The standards
Determining and Setting Plot Style Behavior
Initial Template Setup Template Development Objectives You will complete the following tasks during this stage of template development: Determine and set plot style behavior. Save mechanical, architectural,
Dimensioning. Dimensions: Are required on detail drawings. Provide the shape, size and location description: ASME Dimensioning Standards
Dimensioning Dimensions: Are required on detail drawings. Provide the shape, size and location description: - Size dimensions - Location dimensions - Notes Local notes (specific notes) General notes ASME
The Magic Circle Basic Lesson. Developed by The Alexandria Seaport Foundation
The Magic Circle Basic Lesson Developed by The Alexandria Seaport Foundation The Tools Needed Compass Straightedge Pencil Paper (not graph paper, 8.5 x 11 is fine) Your Brain (the most important tool!)
2. To develop basic skills in the use of drawing instruments and drafting techniques.
IT-111 ENGINEERING DRAFTING SYLLABUS Instructor: R. Edward Rode= Office: Room 110-4, Anzalone Hall Hours: Refer to Schedule Phone: (985-549-2092) Fax : (985-549-5532) Email : erode@selu.edu Course Title:
Standards for Your Career Field
Dimensioning Dimensions Dimensions are used to describe the sizes and relationships between features in your drawing. Dimensions are used to manufacture parts and to inspect the resulting parts to determine
Engineering Drawing I
Instructional Unit Advanced Assembly Drawings -Introduction To Types of Assembly Drawings. -Students will be able -Identify component Class Discussions 3.1.10.B, to identify the details information in
ME 111: Engineering Drawing
ME 111: Engineering Drawing Lecture # 01 Introduction For more detail, visit http://shilloi.iitg.ernet.in/~psr/ Indian Institute of Technology Guwahati Guwahati 781039 1 Syllabus 1. Importance of engineering
Study Unit. Auxiliary Views. This sneak preview of your study material has been prepared in advance of the book's actual online release.
Study Unit Auxiliary Views This sneak preview of your study material has been prepared in advance of the book's actual online release. iii Preview You re entering now into another subject area in your
60 Most Important Engineering Drawing Questions
1. If a client of yours is having difficulty visualizing a design, what type of drawing would be the easiest to understand? A. axonometric B. three-view orthographic C. one-view orthographic D. bimetric
Mechanical Drafting and Design
Job Ready Assessment Blueprint Mechanical Drafting and Design Test Code: 4038 / Version: 01 Copyright 2012. All Rights Reserved. General Assessment Information Mechanical Drafting and Design Blueprint
ENGINEERING GRAPHICS ESSENTIALS. (A Text and Lecture Aid) Second Edition. Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS
ENGINEERING GRAPHICS ESSENTIALS (A Text and Lecture Aid) Second Edition Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:
MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing
the same information given in two different 1. Dimensions should NOT be duplicated, or Dimension Guidelines Incorrect ways.
Dimension Guidelines 1. Dimensions should NOT be duplicated, or the same information given in two different ways. Incorrect 1. Dimensions should NOT be duplicated, or the same information given in two
Graphical Communication for Engineering ENSC 204 Final Exam
Name: Student #: Graphical Communication for Engineering ENSC 204 Final Exam December 16, 2015 Time: 3 hours CLOSED BOOK EXAM Read all the instructions below. Do NOT start the exam until you are told to.