MHz Base Station Antennas for Mobile Communications

Transcription

1 MHz Base Station Antennas for Mobile Communications

2 Photo on title page: Applications for TETRA. Catalogue Issue 2/27 All data published in previous catalog issues hereby becomes invalid. We reserve the right to make alterations in accordance with the requirements of our customers, therefore for binding datas please check valid datasheets! Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS , which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. In addition, please use our information brochure about mounting configurations. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. Quality leads the way As the world s oldest and largest antenna manufacturer, we live up to claim Quality leads the way on a daily basis. One of the fundamental principies is to always be on the lookout for the best solution for our customers. Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 91 and EN ISO 141. Internet: KATHREIN-Werke KG. Phone Fax Anton-Kathrein-Straße 1. P.O. Box D-84 Rosenheim. Germany

3 MHz: Trunking system, Rescue services Directional Antennas MHz: Trunking system, Rescue services MHz: e.g. TETRA, TETRAPOL, GSM 45, CDMA 45, Trunking system MHz: Trunking system, Rescue services Omnidirectional Antennas MHz: Trunking system, Rescue services 7 47 MHz: e.g. TETRA, TETRAPOL, GSM 45, CDMA 45, Trunking system Indoor 7 45 MHz: e.g. TETRA, TETRAPOL, GSM 45, CDMA 45, Trunking system Electrical Accessories Splitters Filter Products Mechanical Accessories Clamps, Downtilt Kits,... Technical Information

4 List of available Catalogues for Mobile Communication Antennas and Accessories 79 6 MHz Base Station Antennas for Mobile Communications MHz Base Station Antennas for Mobile Communiations Ground-to-Air Communication Antennas Antennas for Trains and Buses MHz Filters, Combiners, Amplifiers for Mobile Communications MHz Filters, Combiners, Amplifiers for Mobile Communications The listed catalogues are also available on CD-ROM 4

5 Summary of Types The articles are listed by type number in numerical order. Preferred types for TETRA/ TETRAPOL Type No. Page Type No. Page Type No. Page Type No. Page K K K K K K K K K K K K K K K K K K K K K K K K K K K K 5... K K K K K K K K K K K K K K K K K K K K K K K K K K K

6 Antenna Designs: Antenna Families Harmony of Design and Technology Omnidirectional antennas XPol Directional antennas with HPBW 9 XPol / VPol Directional antennas with HPBW 65 Omnidirectional antennas, broadband Groundplane antenna Directional antennas, logarithmic-periodic 6

7 Antenna Designs: Antenna Families Distinguishing features Design Radome Environmental influences Environmental conditions Large variety of half-power beam width, gain values Small size and elegant design are the distinguishing features of Kathrein s antenna families. The radomes cover the internal antenna components. Fiberglass material guarantees optimum performance with regards to stability, stiffness, UV resistance, painting and best weather protection. The design of Kathrein antennas is based on fundamental engineering knowledge and also on decades of practical experience, during which the various constructions and materials used have proved their outstanding reliability. Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS class 4.1 E. The antennas exceed this standard with regards to the following items: Low temperature: 55 C High temperature (dry): +6 C According to the antenna type selected, customer can choose from different half-power beam widths and different gain values. Low intermodulation After many years of experience in the construction of antennas and after products (typically 15 c) intensive research into the effects of intermodulation, we have been able to optimize the material and technology used for antennas (the given value refers to rd order products measured with 2 carriers of 2 W each). Valid only where indicated in the catalogue! Multi-functional installation hardware Depending on the type, the antennas are equipped with up to 2 fixing points. Panels can be wall mounted without any additional hardware. For mast mounting, stainless steel brackets and mechanical downtilt kits are available. To assist the installation technicians in aligning the panels, an azimuth adjustment tool can be supplied (see Mechanical Accessories). Excellent grounding The antennas are DC grounded according EN MTBF Statement Traditionally passive components like antennas cannot be well calculated due to the lack of a sufficient number of components in the MTBF library. Unfortunately this constraint results in a very inaccurate calculation. Thus such results are technically questionable and unrealistic. In essence, antennas are made out of mechnical parts that do not show any failure rates. Only available failure rates can be calculated into an MTBF value. Consequently such components cannot be listed in any MTBF library. Remote Electical Tilt System Kathrein hereby states that RET devices, as far as the functionality and AISG Compliancy features are described within the AISG / GPP standard, are compliant with the standard. 7

8 8

9 Summary Directional Antennas MHz Directional MHz Type Type No. Height Input Page [mm] Yagi K N female Yagi K N female Yagi K N female 11 Gain ref. λ /2 dipole 9

10 Directional MHz Directional Antennas Polarization H or V K : Yagi K : Yagi Type No. K K Frequency range 68 8 MHz MHz Polarization Usable for horizontal or vertical polarization. Gain (ref. λ /2 dipole) Impedance 5 Ω VSWR < 1.5 Max. power 1 W (at 5 C ambient temperature) Mounting: Grounding: Special features: Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. The antenna will be shipped dismounted. 162 Mechanical specifications 77 Input N female Weight 12 kg Wind load 26 N (at 15 km/h) Max. wind velocity 18 km/h in E-plane in H-plane Packing size Height Distance dipole / mast 2154 x 798 x 12 mm approx. 2 mm approx. 12 mm

11 Directional Antenna Polarization V Directional MHz 4-element Yagi antenna, large bandwidth. Hot-dip galvanized steel. Gain 6. Yagi Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K MHz Vertical 6 5 Ω VSWR < 1.5 Max. power W (at 5 C ambient temperature) Mounting: Grounding: Hot-dip galvanized steel. All screws and nuts: Stainless steel. On masts from mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. Radiation patterns at different frequencies: 14 7 Horizontal 69 MHz Vertical 69 MHz 12 6 Horizontal 77 MHz 8 Vertical 77 MHz 58 Mechanical specifications Input N female Weight 22 kg Wind load 52 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 2424 x 2118 x 182 mm Height approx. 28 mm Yagi length approx. 2 mm Horizontal 86 MHz Vertical 86 MHz 11

12 12

13 Summary Directional Antennas MHz Type Type No. Height Input Page [mm] Directional MHz Yagi K N female 14 Yagi K N female 15 Yagi K N female 16 Panel K N female 17 Gain ref. λ /2 dipole 1

14 Directional Antenna Polarization H or V Directional MHz Yagi Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K MHz Usable for horizontal or vertical polarization. 5 Ω VSWR < 1.4 Max. power 56 W (at 5 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. Mounting: On masts from mm diameter, clamps supplied. Grounding: All metal parts of the antenna including the mounting kit are DC grounded. 17 Mechanical specifications 8 Input N female Weight 6.5 kg Wind load 145 N (at 15 km/h) Max. wind velocity 2 km/h in E-plane in H-plane Packing size Height Yagi length 1124 x 816 x 92 mm approx. 6 mm approx. 65 mm 14

15 Directional Antenna Polarization H or V Yagi Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K MHz Usable for horizontal or vertical polarization. 4 5 Ω VSWR < 1. Max. power 8 W (at 5 C ambient temperature) Directional MHz Hot-dip galvanized steel. All screws and nuts: Stainless steel. Mounting: On masts from mm diameter, clamps supplied. Grounding: All metal parts of the antenna including the mounting kit are DC grounded. 118 Mechanical specifications 58 Input N female Weight 7.5 kg Wind load 17 N (at 15 km/h) Max. wind velocity 2 km/h in E-plane in H-plane Packing size Height Yagi length 1112 x 92 x 94 mm approx. 1 mm approx. 75 mm 15

16 Directional Antenna Polarization H or V Directional MHz Yagi Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K MHz Usable for horizontal or vertical polarization Ω VSWR < 1.5 Max. power 25 W (at 5 C ambient temperature) Mounting: Grounding: Shipping: Antenna: Weather-resistant aluminum. All screws and nuts: Stainless steel. On masts from 6 5 mm diameter, by means of supplied mounting kit. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. The antenna will be shipped dismounted. Mechanical specifications 5 6 Input N female Weight kg Wind load (at 15 km/h) Horizontal: Vertical: lateral: 25 N 2 N frontal: 14 N 14 N in E-plane in H-plane Max. wind velocity 2 km/h 22 km/h Packing size 1954 x 186 x 162 mm Height approx. 22 mm Yagi length approx. 19 mm 16

17 Directional Antenna Polarization H or V Yagi Type No. Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K MHz Usable for horizontal or vertical polarization. 8 5 Ω VSWR < 1.15 Max. power 1 W (at 5 C ambient temperature) Directional MHz Mounting: Combination: Grounding: Ice protection: Hot-dip galvanized steel. All screws and nuts: Stainless steel. Via pair of clamps K at masts from mm dia. or via pair of clamps K 61 1 at masts from mm dia. (not supplied). The antenna is especially suitable as a component in arrays to achieve various radiation patterns. All metal parts of the antenna including the mounting kit are DC grounded. Fiberglass enclosure of its critical points and the antenna s extremely sturdy construction keep it operational even during heavy icing. Mechanical specifications Input Weight N female 25 kg Wind load 66 N (at 15 km/h) Max. wind velocity Packing size 22 km/h 14 x 14 x 75 mm Width/height/depth 12 x 12 x 5 mm in E-plane in H-plane 17

18 18

19 Summary Directional Antennas MHz Type Type No. Height Input Page [mm] XPol Panel i x 7-16 female 2 XPol Panel i x 7-16 female 21 XPol Panel i x 7-16 female 22 XPol Panel i 6 T x 7-16 female 2 XPol Panel i x 7-16 female 24 XPol Panel i x 7-16 female 25 Directional MHz VPol Panel i K N female 26 VPol Panel i female 27 VPol Panel i female 28 VPol Panel i female 29 VPol Panel i female VPol Panel i female 1 LogPer i K N female 2 LogPer i K female 2 LogPer i female Corner i K N female 4 RHCPol Helix i K N female 5 Remote Electrical Tilt (RET) System 6 New Products 19

20 Panel Dual Polarization Half-power Beam Width 8 5 X 65 TETRA/ TETRAPOL Directional MHz XPol Panel i Type No Frequency range MHz 4 5 MHz Polarization +45, , 45 Gain 11.5 i 12 i Half-power beam width Horizontal: 68 Horizontal: 65 Copolar +45 / 45 Vertical: 7 Vertical: 2 Front-to-back ratio, copolar > 25 Isolation > Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power per input 5 W (at 5 C ambient temperature) Radiators: Tin-plated copper. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. 9 Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. 25 Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded MHz Horizontal Pattern Vertical Pattern 4 5 MHz Horizontal Pattern Vertical Pattern 2 Mechanical specifications Input 2 x 7-16 female Connector position Rearside Weight 12 kg Wind load Frontal: 55 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 715 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 62 x 562 x 274 mm Height/width/depth 992 / 492 / 19 mm 2

21 Panel Dual Polarization Half-power Beam Width Adjust. Electr. Downtilt set by hand or by optional RCU (Remote Control Unit) XPol Panel i 2 16 T Type No. 8 4 X 65 Frequency range MHz 4 47 MHz Polarization +45, , 45 Gain (i) Tilt Half-power beam width Horizontal: 66 Horizontal: 62 Copolar +45 / 45 Vertical: 22 Vertical: 19 Electrical tilt 2 16, continuously adjustable Front-to-back ratio, copolar > 25 (18 ± ) Cross polar ratio Typically: 25 Maindirection ±6 > Isolation > Impedance 5 Ω VSWR < 1.5 Intermodulation IM Max. power per input < 15 c (2 x 4 m carrier) 4 W (at 5 C ambient temperature) TETRA/ TETRAPOL Directional MHz Ice protection: Radiator: Tin-plated copper. Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded MHz: +45 / Horizontal Pattern 8 4 MHz: +45 / Vertical Pattern 2 16 electrical downtilt 22 Mechanical specifications Input 2x 7-16 female Connector position Bottom Adjustment 1x, Position bottom mechanism continuously adjustable Weight 19 kg Wind load Frontal: 12 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Rearside: 2 N (at 15 km/h) Max. wind velocity 2 km/h Packing size Approx. 225 x 6 x 215 mm Height/width/depth 1999 / 575 / 199 mm Horizontal Pattern Vertical Pattern 2 16 electrical downtilt 21

22 Panel Dual Polarization Half-power Beam Width 8 5 X 65 TETRA/ TETRAPOL Directional MHz XPol Panel i Type No Frequency range MHz 4 5 MHz Polarization +45, , 45 Gain 14.5 i 15 i Half-power beam width Horizontal: 65 Copolar +45 / 45 Vertical: 18 Front-to-back ratio, copolar > 25 Isolation Impedance > 5 Ω 185 VSWR < 1.5 Intermodulation IM (2 x 4 m carrier) < 15 c 25 Max. power per input 5 W (at 5 C ambient temperature) Radiators: Tin-plated copper. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. 8 Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded / 45 Polarization Mechanical specifications Input Connector position 2 x 7-16 female Rearside 18 Weight 19 kg Wind load Frontal: 1 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Rearside: 154 N (at 15 km/h) Max. wind velocity 2 km/h Horizontal Pattern Vertical Pattern Packing size Height/width/depth 26 x 562 x 274 mm 2 / 492 / 19 mm 22

23 Panel Dual Polarization Half-power Beam Width Fixed Electrical Downtilt 8 47 X 65 6 TETRA/ TETRAPOL XPol Panel i 6 T Type No Frequency range MHz 4 47 MHz Polarization +45, , 45 Gain 2 x 14.5 i 2 x 14.7 i Directional MHz Half-power beam width Horizontal: 68 Horizontal: 65 Copolar +45 / 45 Vertical: 18 Vertical: 17 Electrical tilt 6 6 Front-to-back ratio, copolar > 25 > 24 Isolation > > 185 Impedance 5 Ω 5 Ω VSWR < 1.5 < Intermodulation IM < 15 c (2 x 4 m carrier) Max. power per input 5 W (at 5 C ambient temperature) Radiators: Tin-plated copper. Reflector screen: Weatherproof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. 8 Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded MHz: +45 / Horizontal Pattern 8 4 MHz: +45 / Vertical Pattern 6 electrical downtilt 18 Mechanical specifications Input 2 x 7-16 female Connector position Rearside Weight 19 kg Wind load Frontal: 1 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Rearside: 154 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 26 x 562 x 274 mm Height/width/depth 2 / 492 / 19 mm Horizontal Pattern Vertical Pattern 6 electrical downtilt 2

24 Panel Dual Polarization Half-power Beam Width 8 5 X 88 TETRA/ TETRAPOL Directional MHz XPol Panel i Type No Frequency range MHz 4 5 MHz Polarization +45, , 45 Gain 2 x i 2 x.5 i Half-power beam width Horizontal: 88 Horizontal: 86 Copolar +45 / 45 Vertical: 4 Vertical: 5 Front-to-back ratio, copolar > 2 > 2 Isolation > > Impedance 5 Ω 5 Ω VSWR < 1.5 < 1.5 Intermodulation IM Max. power per input < 15 c (2 x 4 m carrier) 5 W (at 5 C ambient temperature) Ice protection: Grounding: Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 4 5 MHz: +45 / 45 Polarization Horizontal Pattern Vertical Pattern 8 4 MHz: +45 / 45 Polarization Horizontal Pattern Vertical Pattern 4 Mechanical specifications Input Connector position 2 x 7-16 female Bottom Weight.5 kg Wind load Frontal: 6 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 114 x x 24 mm Height/width/depth 7 / 17 / 19 mm 24

25 Panel Dual Polarization Half-power Beam Width 8 5 X 88 TETRA/ TETRAPOL XPol Panel i Type No Frequency range MHz 4 5 MHz Polarization +45, , 45 Gain 2 x 1 i 2 x 1.5 i Half-power beam width Horizontal: 88 Horizontal: 86 Copolar +45 / 45 Vertical: 2 Vertical: 17 Front-to-back ratio, copolar > 2 > 2 Isolation > > Impedance 5 Ω 5 Ω VSWR < 1.5 < 1.5 Intermodulation IM Max. power per input < 15 c (2 x 4 m carrier) 5 W (at 5 C ambient temperature) Directional MHz Ice protection: Grounding: Reflector screen: Weather-proof aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 4 5 MHz: +45 / 45 Polarization Horizontal Pattern Vertical Pattern 8 4 MHz: +45 / 45 Polarization Horizontal Pattern Vertical Pattern 2 Mechanical specifications Input Connector position 2 x 7-16 female Bottom Weight 18.5 kg Wind load Frontal: 715 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 21 x x 24 Height/width/depth 1997 / 17 / 19 mm 25

26 Panel Vertical Polarization Half-power Beam Width V 6 Directional MHz VPol Panel i Type No. K Frequency range MHz Polarization Vertical Gain 9 i Half-power beam width H-plane: 6 E-plane: 6 Impedance 5 Ω VSWR < 1.4 Max. power 5 W (at 5 C ambient temperature) Arrays: This antenna is especially suitable as a component in arrays to achieve various radiation patterns. Scope of supply: Antenna including two weather-proof covers for straight and elbow connector, but without mounting hardware. Dipoles and reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. 4 Attachment: Use clamps K for tubular mast diameters of mm (see the Mechanical Accessories part of this catalogue). 186 Ice protection: Grounding: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled. Mounting Dimensions Horizontal Pattern 6 Vertical Pattern 6 Mechanical specifications Input N female Connector position Rearside Weight 6 kg Wind load Frontal: 22 N (at 15 km/h) Lateral: N (at 15 km/h) Rearside: N (at 15 km/h) Max. wind velocity 2 km/h Packing size 6 x 567 x 282 mm Height/width/depth 49 / 49 / 29 mm 26

27 Multi-band Panel Vertical Polarization Half-power Beam Width 8 5 V 65 TETRA/ TETRAPOL VPol Panel i Type No Frequency range MHz 4 5 MHz Polarization Vertical Vertical Gain 11.5 i 12 i Half-power beam width Horizontal: 68 Horizontal: 6 Vertical: 7 Vertical: 2 Front-to-back ratio, copolar > 18 > 2 Impedance 5 Ω VSWR < 1.5 Intermodulation IM Max. power per input < 15 c (2 x 4 m carrier) 5 W (at 5 C ambient temperature) Directional MHz Ice protection: Grounding: Reflector screen: Weather-proof aluminum. Radiator: Tin-plated copper. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 8 4 MHz Horizontal Pattern Vertical Pattern MHz Horizontal Pattern Vertical Pattern 2 Mechanical specifications Input 1 x 7-16 female Connector position Rearside Weight 12 kg Wind load Frontal: 55 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 715 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 62 x 562 x 274 mm Height/width/depth 992 / 492 / 19 mm 27

28 Multi-band Panel Vertical Polarization Half-power Beam Width 8 5 V 65 TETRA/ TETRAPOL Directional MHz VPol Panel i Type No Frequency range MHz 4 5 MHz Polarization Vertical Vertical Gain 14.5 i 15 i Half-power beam width Horizontal: 68 Horizontal: 6 Vertical: 18 Vertical: 16 Front-to-back ratio, copolar > 2 > 2 Impedance 5 Ω VSWR < 1.5 Intermodulation IM Max. power per input < 15 c (2 x 4 m carrier) 5 W (at 5 C ambient temperature) Ice protection: Grounding: Reflector screen: Weather-proof aluminum. Radiator: Tin-plated copper. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. 8 4 MHz Horizontal Pattern Vertical Pattern MHz Horizontal Pattern Vertical Pattern 16 Mechanical specifications Input 1 x 7-16 female Connector position Rearside Weight 2 kg Wind load Frontal: 1 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Rearside: 154 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 26 x 562 x 274 mm Height/width/depth 2 / 492 / 19 mm 28

29 Eurocell Panel Vertical Polarization Half-power Beam Width 8 4 V 115 TETRA/ TETRAPOL VPol Panel i Type No Frequency range 8 4 MHz Polarization Vertical Gain 8.5 i Half-power beam width Horizontal: 115 Vertical: 8 Front-to-back ratio > 18 Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Directional MHz Attachment: Ice protection: Grounding: Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. See the Mechanical Accessories part of this catalogue. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 115 Horizontal Pattern Vertical Pattern 8 Mechanical specifications Input 7-16 female Connector position Bottom Weight 4.5 kg Wind load Frontal: 16 N (at 15 km/h) Lateral: N (at 15 km/h) Rearside: 6 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 12 x 272 x 16 mm Height/width/depth 974 / 258 / mm 29

30 Eurocell Panel Vertical Polarization Half-power Beam Width 8 4 V 115 TETRA/ TETRAPOL Directional MHz VPol Panel i Type No Frequency range 8 4 MHz Polarization Vertical Gain 11.5 i Half-power beam width Horizontal: 115 Vertical: 18 Front-to-back ratio > 18 Impedance 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Attachment: Ice protection: Grounding: Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. See the Mechanical Accessories part of this catalogue. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 115 Horizontal Pattern Vertical Pattern 18 Mechanical specifications Input 7-16 female Connector position Rearside Weight 9 kg Wind load Frontal: 4 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 75 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 262 x 272 x 16 mm Height/width/depth 194 / 258 / mm

31 Panel Vertical Polarization Half-power Beam Width 4 47 V 12 VPol Panel i Type No Frequency range 4 47 MHz Polarization Vertical Gain 9 i Half-power beam width H-plane: 12 E-plane: 5 Impedance 5 Ω VSWR < 1.5 Max. power 5 W (at 5 C ambient temperature) Directional MHz Scope of supply: Antenna including two weather-proof covers for straight and elbow connector, but without mounting hardware. Dipole system: Brass and copper. Reflector screen: Weather-resistant aluminum. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. Attachment: Use clamps K for tubular mast diameters of mm (see the Mechanical Accessories part of this catalogue). Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. 9 Grounding: All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 6 Mounting Dimensions 12 5 Mechanical specifications Input 7-16 female Connector position Rearside Weight 9 kg Horizontal Pattern Vertical Pattern Wind load Frontal: 5 N (at 15 km/h) Lateral: 22 N (at 15 km/h) Rearside: 715 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 62 x 562 x 274 mm Height/width/depth 992 / 492 / 19 mm 1

32 Logarithmic-periodic Vertical/ Horizontal Polarization Half-power Beam Width V or H 67 Directional MHz LogPer i Type No. Frequency range Polarization Gain K K MHz Usable for horizontal or vertical polarization..5 i Half-power beam width H-plane: 67 E-plane: 5 Side-lobe Suppression > 25 at MHz > 2 at MHz Impedance 5 Ω VSWR < 1.4 Max. power W (at 5 C ambient temperature) Arrays: Several antennas can be combined to increase the gain and to produce radiation patterns with very high side-lobe suppressions. For vertical polarization For horizontal polarization Scope of supply: Attachment: Ice protection: Grounding: Antenna with weather protective casing for straight connectors. Radiator and mounting kit: Aluminum. Radome: Fiberglass, colour: Grey. All screws and nuts: Stainless steel. To tubular masts of mm diameter using supplied clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. For vertical polarization For horizontal polarization Radiation Pattern in H-Plane 67 Pariation Pattern in E-Plane 5 Mechanical specifications K K Input N female 7-16 female Weight 9 kg Wind load: Vertical: Frontal: 55 N (at 15 km/h) Lateral: 44 N (at 15 km/h) Horizontal: Frontal: 55 N (at 15 km/h) Lateral: 9 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 1172 x 72 x 225 mm Height/width/depth 115 / 5 / 18 mm 2

33 Logarithmic-periodic Vertical Polarization Half-power Beam Width VPol LogPer i Type No V Frequency range 8 4 MHz 4 47 MHz MHz TETRA/ TETRAPOL Polarization Vertical Gain 9.2 i 9 i 8.7 i Half-power beam width Horizontal: 8 Horizontal: 85 Horizontal: 88 Vertical: 61 Vertical: 6 Vertical: 59 Impedance 5 Ω VSWR < 1.5 Directional MHz Intermodulation IM Max. power Scope of supply: Attachment: Ice protection: Grounding: < 15 c (2 x 4 m carrier) 5 W (at 5 C ambient temperature) Antenna with weather protective casing for straight connectors. Radiator: Weather resistant aluminium. Radome: Fiberglass, colour: White. All screws and nuts: Stainless steel. To tubular masts of 5 8 mm diameter depending on the separate available clamps. Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. 8 4 MHz: +45 / Horizontal Pattern Vertical Pattern 4 47 MHz: +45 / Mechanical specifications Horizontal Pattern Vertical Pattern MHz: +45 / 45 Input Connector position 7-16 female Rearside, pointing downwards Weight 6 kg Wind load Frontal: 54 N (at 15 km/h) Lateral: 15 N (at 15 km/h) Max. wind velocity 18 km/h Packing size Height/width/depth 915 x 485 x 485 mm 785 / 4 / 4 mm Horizontal Pattern Vertical Pattern

34 Corner-reflector Antenna Vertical Polarization Half-power Beam Width 6 49 V 44 Directional MHz VPol Corner i Type No. K Frequency range 6 49 MHz Polarization Vertical Gain 11 i Half-power beam width H-plane: 44 E-plane: 67 Impedance 5 Ω VSWR < 1.5 at 6 49 MHz < 1. at 4 47 MHz Max. power 18 W (at 5 C ambient temperature) Scope of supply: Attachment: Special features: Grounding: Antenna with weather protective casing for straight connectors, mounting kit included. Radiator and reflector: Weather-resistant aluminum. Mounting U-bold: Stainless steel. All screws and nuts: Stainless steel. To tubular masts of 54 mm diameter using supplied U-bolts. The reflector screen folds together for transport. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded Mechanical specifications Input N female Weight 2.8 kg Wind load 14 N (at 15 km/h) Horizontal Pattern Vertical Pattern Max. wind velocity Packing size Height/width/depth 15 km/h 842 x 524 x 187 mm 5 / 1155 / 577 mm 4

35 Helix Antenna Right Handed Circular Polarization Half-power Beam Width 4 47 RHC RHCPol Helix i Type No. K Frequency range 4 47 MHz Polarization Right handed circular Gain 12 i (ref. to the circularly polarized isotropic antenna) Half-power beam width Impedance 5 Ω VSWR < 1.2 Max. power 56 W (at 5 C ambient temperature) Directional MHz Scope of supply: Attachment: Special features: Grounding: Antenna with weather protective casing for straight connectors, mounting kit included. Antenna: Copper band helix in protective fiberglass tube, colour: Grey. Reflector screen: Weather-resistant aluminum. Attachment construction: Hot dip galvanized steel. All screws and nuts: Stainless steel. To tubular masts of mm diameter using supplied U-bolts. The reflector screen is made of two parts and can be removed for transport. All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded. Mounting Instructions Mechanical specifications Relative field strength in mid-band Input N female Weight 12 kg Wind load Frontal: 45 N (at 15 km/h) Lateral: 175 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 1684 x 88 x 277 mm Reflector diameter 718 mm Length / tube dia. 154 / 24 mm 5

36 RET System Directional MHz Network planning is becoming ever more complicated, even for TETRA/TETRAPOL systems. The challenge for wireless network operators is to balance coverage, capacity, call quality and costs, in order to gain maximum revenue from their network. The possibility of coverage adjustment through the vertical antenna pattern is thus a very important aspect for mobile communication planners. Kathrein s Remote Electrical Tilt (RET) system represents the latest antenna system technology. RET components: Remote Control Unit (RCU) Central Control Unit (CCU) Control cable DC power and signal splitter Lightning protection device Earthing clamp Optional: Smart bias-tee Advantage of Kathrein s RET system: Easy network extension as no special installation teams are required Kathrein s overall RET System works in accordance with the AISG (Antenna Interface Standards Group) standard and the GPP (rd Generation Partnership Project). For further infomation please contact: antennas.mobilcom@kathrein.de 6

37 Summary Omnidirectional Antennas MHz Type Type No. Height Input Page [mm] VPol Omni K UHF female 8 VPol Omni K N female 9 VPol Omni K N female 9 VPol Omni / /6 /.5 K x N female 4 VPol Omni K N female 41 Gain ref. λ /2 dipole Omnidirectional MHz 7

38 Omnidirectional Antenna Vertical Polarization V Omnidirectional MHz VPol Omni Type No. Antenna Spare radials Frequency range Polarization Gain (ref. λ /2 dipole) Impedance Max. power K K MHz Vertical 5 Ω 5 W (at 5 C ambient temperature) Radiator and radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. Mounting: Tuning: Grounding: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 54 mm diameter (connecting cable runs outside the mast). By cutting radiator and radials to length in accordance to the mounting instructions. The metal parts of the antenna including the mounting kit are DC grounded. 78 On the tip of a tubular mast Laterally at the tip of a tubular mast 2,2 1,8 1,4 1, Vertical Pattern Standing Wave Ratio (VSWR) Examples of matching at various frequencies VSWR 2,2 1,8 1,4 1, VSWR 27 27,6 4 4, , Mechanical specifications Input Weight * Wind load * Max. wind velocity Packing size Radiator length Length of radials * for max. antenna length UHF female 1.6 kg 1 N (at 15 km/h) 15 km/h 274 x 16 x mm max. 25 mm max. 25 mm 8

39 Omnidirectional Antennas Vertical Polarization V K : VPol Omni K : VPol Omni K K K K Type No. Antenna Spare radials Frequency range 68 8 MHz MHz Polarization Gain (ref. λ /2 dipole) Impedance Vertical 5 Ω VSWR < 1.5 Max. power 75 W (at 5 C ambient temperature) Radiator: Stainless steel. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. Omnidirectional MHz Mounting: Side mounting at a mast: Grounding: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 4 mm diameter (connecting cable runs outside the mast). See catalogue part Technical Information. All metal parts of the antenna including the mounting kit are DC grounded. On the tip of a tubular mast Laterally at the tip of a tubular mast Horizontal Pattern 78 Vertical Pattern Mechanical specifications Input K K N female Weight 1.8 kg 1.6 kg Wind load 7 N 65 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 1114 x 12 x 112 mm Radiator length 747 mm 68 mm Length of radials 5 mm 97 mm 9

40 Dual-band Omnidirectional Antenna Vertical Polarization V V Omnidirectional MHz VPol Omni / /6 /.5 Type No. Antenna Spare radials K K Frequency range MHz and MHz MHz Polarization Vertical Gain (ref. λ /2 dipole).5 Decoupling Impedance < between 2 m band and 4 m band 5 Ω VSWR < 1.5 Max. power W (at 5 C ambient temperature) Radiator: Weather-resistant aluminum in fiberglass radome. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. Mounting: Special features: Grounding: To pipes of 54 mm diameter by means of mounting kit (supplied). The antenna must be mounted in such a manner, that the feeder cables runs outside the mast. The radials can be fold up. All metal parts of the antenna including the mounting kit are DC grounded. Mechanical specifications 78 Input 2 x N female Weight 2.7 kg Wind load 9 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 116 x 12 x 1 mm Radiator length 1121 mm Horizontal Pattern Vertical Pattern Diameter Length of radials 5 mm mm 4

41 Omnidirectional Off-set Antenna Vertical Polarization V VPol Omni Type No. Frequency range Polarization Radiation pattern Gain (ref. λ /2 dipole) Impedance K MHz Vertical Preferred direction: mast to radiator. 2 5 Ω VSWR < 1.5 Max. power 2 W (at 5 C ambient temperature) Hot-dip galavanized steel. Radome: Fiberglass. All screws and nuts: Stainless steel. Omnidirectional MHz Mounting: Grounding: On masts from mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is coupled capacitively. Mechanical specifications 78 Input N female Weight 9 kg Wind load 165 N (at 15 km/h) Max. wind velocity 2 km/h Horizontal Pattern Vertical Pattern Mast diameter Packing size Dipole length Distance dipole / mast mm 18 x 948 x 7 mm approx. 175 mm approx. 87 mm 41

42 42

43 Summary Omnidirectional Antennas MHz Type Type No. Height Input Page [mm] VPol Omni / /6 /.5 K x N female 44 VPol Omni K cable termination 45 VPol Omni N female 45 VPol Omni K cable termination 46 VPol Omni K cable termination 46 VPol Omni K cable termination 46 VPol Omni K N female 47 Gain ref. λ /2 dipole Omnidirectional MHz 4

44 Dual-band Omnidirectional Antenna Vertical Polarization V V VPol Omni / /6 /.5 Type No. Frequency range MHz and MHz MHz Polarization Vertical Gain (ref. λ /2 dipole).5 Decoupling Impedance Antenna Spare radials K K < between 2 m band and 4 m band 5 Ω VSWR < 1.5 Max. power W (at 5 C ambient temperature) Omnidirectional MHz Mounting: Radiator: Weather-resistant aluminum in fiberglass radome. Radials: Fiberglass with imbedded stranded copper wire. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. To pipes of 54 mm diameter by means of mounting kit (supplied). The antenna must be mounted in such a manner, that the feeder cables runs outside the mast. Special features: The radials can be fold up. Grounding: All metal parts of the antenna including the mounting kit are DC grounded. Mechanical specifications 78 Input 2 x N female Weight 2.7 kg Wind load 9 N (at 15 km/h) Max. wind velocity 18 km/h Packing size 116 x 12 x 1 mm Radiator length 1121 mm Horizontal Pattern Vertical Pattern Diameter Length of radials 5 mm mm 44

45 Omnidirectional Antennas Vertical Polarization V VPol Omni Type No. Antenna Spare radials Frequency range Polarization Gain (ref. λ /2 dipole) Impedance K K K MHz Vertical 5 Ω VSWR < 1.5 Max. power 17 W 7 W (at 5 C ambient temperature) Mounting: Radiator and radials: Weather-resistant aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 4 mm diameter (connecting cable runs outside the mast). Omnidirectional MHz Side mounting at a mast: See catalogue part Mechanical Accessories. Grounding: All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled. On the tip of a tubular mast Laterally at the tip of a tubular mast Horizontal Pattern 78 Vertical Pattern Mechanical specifications K Input By means of N female a cable RG-21/U with termination inside antenna. Weight 1.2 kg Wind load 25 N (at 15 km/h) Max. wind velocity 2 km/h Packing size 654 x 112 x 97 mm Radiator length 422 mm Length of radials 617 mm 45

46 Omnidirectional Antennas Vertical Polarization V K : VPol Omni K : VPol Omni K : VPol Omni Type No. K K K Frequency range MHz MHz MHz Polarization Gain (ref. λ /2 dipole) Impedance Vertical 5 Ω VSWR < 1.4 Max. power 1 W (at 5 C ambient temperature) Radiator and base: Weather-resistant aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. Omnidirectional MHz Mounting: Side mounting at a mast: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of a tubular mast of 4 54 mm diameter (connecting cable runs inside the mast). 2. Laterally at the tip of a tubular mast of 2 4 mm diameter (connecting cable runs outside the mast). See catalogue part Mechanical Accessories. Grounding: All metal parts of the antenna including the mounting kit are DC grounded. The inner conductor is capacitively coupled. Horizontal Pattern On the tip of a tubular mast Laterally at the tip of a tubular mast 78 Vertical Pattern Mechanical specifications Input Cable needed Weight Wind load Max. wind velocity K K K Via terminals inside antenna. RG-21/U 1. kg 5 N (at 15 km/h) 2 km/h Packing size 1254 x 112 x 97 mm Height 85 mm 42 mm 99 mm 46

47 Omnidirectional Off-set Antenna Vertical Polarization V VPol Omni Type No. Frequency range Polarization Radiation Pattern Gain (ref. λ /2 dipole) Impedance K MHz Vertical Preferred direction: Mast to radiator. 2 5 Ω VSWR < 1.4 Max. power 44 W (at 5 C ambient temperature) Hot-dip galvanized steel. All screws and nuts: Stainless steel. Mounting: Grounding: On masts of mm diameter, clamps supplied. All metal parts of the antenna including the mounting kit are DC grounded. Omnidirectional MHz Radiation Pattern with different mast diameters: Horizontal Pattern 6 mm Horizontal Pattern 115 mm Mechanical specifications Input N female Weight 4.5 kg Wind load 9 N (at 15 km/h) Max. wind velocity 2 km/h Mast diameter mm Vertical Pattern 6 mm Vertical Pattern 115 mm Packing size Dipole length Distance dipole / mast 864 x 598 x 87 mm 84 mm 5 mm 47

48 48

49 Summary Omnidirectional Antennas 7 47 MHz Type Type No. Height Input Page [mm] VPol Omni i N female 5 VPol Omni i K N female 5 VPol Omni i female 51 VPol Omni i K female 52 VPol Omni i K N female 5 VPol Omni i K N female 5 VPol Omni i female 54 VPol Omni i female 55 VPol Omni i N female 55 VPol Omni i female 55 VPol Omni i K female 56 VPol Omni i 8.5 T female 57 VPol Omni i female 58 VPol Omni i 8.5 T female 59 VPol Omni i female 6 VPol Omni i K N female 61 New Products Omnidirectional 7 47 MHz 49

50 Omnidirectional Antennas Vertical Polarization V TETRA/ TETRAPOL 77 : VPol Omni i K : VPol Omni i Type No. 77 K Frequency range 7 4 MHz MHz Polarization Gain Impedance Vertical 2 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power W (at 5 C ambient temperature) Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. Omnidirectional 7 47 MHz Mounting: Grounding: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern 78 Mechanical specifications Input Connector position N female Bottom Weight 1. kg.8 kg Radome diameter Wind load Max. wind velocity 77 K mm 2 N (at 15 km/h) 2 km/h Packing size [mm] 112 x 97 x x 97 x 614 Height [mm] Side-mounting brackets see cataloge part Mechanical Accessories

51 Omnidirectional Antenna Vertical Polarization 8 46 V TETRA/ TETRAPOL VPol Omni i Type No. Frequency range Polarization Gain Impedance MHz Vertical 5 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Brass. Radome: Fiberglass colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: Grounding: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. Omnidirectional 7 47 MHz On the tip of a tubular mast Laterally at the tip of a tubular mast Mechanical specifications Vertical Pattern Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 1.4 kg 21 mm 4 N (at 15 km/h) 2 km/h 112 mm x 97 mm x 1495 mm 14 mm Side-mounting brackets see cataloge part Mechanical Accessories 51

52 Omnidirectional Antenna Vertical Polarization 8 4 V TETRA/ TETRAPOL VPol Omni i Type No. Frequency range Polarization Gain Impedance K MHz Vertical 5 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: The antenna can be attached laterally at the tip of a tubular mast of 5 94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast). Omnidirectional 7 47 MHz Excellent grounding: From the solid metal tip right down to the base of the high gain antennas the grounding crosssection is 22 mm 2 copper or more, exceeding EN maximum mast top Vertical Pattern Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 5.5 kg 51 mm 14 N (at 15 km/h) 2 km/h 1878 x 26 x 152 mm 1612 mm 52 Side-mounting brackets see cataloge part Mechanical Accessories

53 Omnidirectional Antennas Vertical Polarization V K : VPol Omni i K : VPol Omni i Type No. K K Frequency range 46 4 MHz MHz Polarization Gain Impedance Vertical 5 i 5 Ω VSWR < 1.5 Max. power 55 W (at 5 C ambient temperature) Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. Mounting: Grounding: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. Omnidirectional 7 47 MHz On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern Mechanical specifications Input Connector position Weight Wind load Max. wind velocity K K N female Bottom 1.2 kg 4 N (at 15 km/h) 5 N (at 15 km/h) 2 km/h Packing size [mm] 15 x 1 x 125 x 1 x Height 127 mm 1144 mm Side-mounting brackets see cataloge part Mechanical Accessories 5

54 Omnidirectional Antenna Vertical Polarization 8 4 V TETRA/ TETRAPOL VPol Omni i Type No. Frequency range Polarization Gain Impedance MHz Vertical 7 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 2 W (at 5 C ambient temperature) Radiator: Brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Omnidirectional 7 47 MHz Mounting: Grounding: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. On the tip of a tubular mast Laterally at the tip of a tubular mast Mechanical specifications Vertical Pattern 18 Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 1.8 kg 21 mm 65 N (at 15 km/h) 2 km/h Approx. 112 x 97 x 22 mm Approx. 26 mm 54 Side-mounting brackets see cataloge part Mechanical Accessories

55 Omnidirectional Antennas Vertical Polarization V K : VPol Omni i , 72 88: VPol Omni i : VPol Omni i Type No Frequency range MHz 46 4 MHz Polarization Gain Impedance Vertical 7 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. Mounting: Grounding: The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. Omnidirectional 7 47 MHz On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern 18 Mechanical specifications N female female Connector position Bottom Weight Radome diameter Wind load Max. wind velocity Packing size Height 1.6 kg 21 mm 6 N (at 15 km/h) 2 km/h 112 x 97 x 2124 mm 216 mm Side-mounting brackets see cataloge part Mechanical Accessories 55

56 Omnidirectional Antenna Vertical Polarization 8 4 V TETRA/ TETRAPOL VPol Omni i Type No. Frequency range Polarization Gain Impedance K MHz Vertical 7.5 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, dia. 51 mm, colour: Grey. Base: Aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). Omnidirectional 7 47 MHz Grounding: The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is capacitively coupled. maximum mast top Vertical Pattern Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8. kg 51 mm 2 N (at 15 km/h) 2 km/h 16 x 148 x 112 mm 284 mm 56 Side-mounting brackets see cataloge part Mechanical Accessories

57 Omnidirectional Antenna Vertical Polarization Fixed Elctrical Downtilt 8 4 V 8.5 TETRA/ TETRAPOL VPol Omni i 8.5 T Type No. Frequency range Polarization Gain Electrical tilt Impedance MHz Vertical 7.5 i 8.5, fixed 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). Grounding: The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is capacitively coupled. Omnidirectional 7 47 MHz maximum mast top Vertical Pattern 8.5 electrical downtilt Mechanical specifications Input Connector position Weight Radome diameter Windload Max. wind velocity Packing size Height 7-16 female Bottom 8. kg 51 mm 2 N (at 15 km/h) 18 km/h 55 x 148 x 112 mm 282 mm Side-mounting brackets see cataloge part Mechanical Accessories 57

58 Omnidirectional Antenna Vertical Polarization Fixed Electrical Downtilt 8 4 V 5 TETRA/ TETRAPOL VPol Omni i 5 T Type No. Frequency range Polarization Gain Electrical tilt Impedance MHz Vertical 8 i 5, fixed 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). Omnidirectional 7 47 MHz Grounding: The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is coupled capacitively. maximum mast top Vertical Pattern 5 electrical downtilt Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8.5 kg 51 mm 2 N (at 15 km/h) 18 km/h 55 x 148 x 112 mm 282 mm 58 Side-mounting brackets see cataloge part Mechanical Accessories

59 Omnidirectional Antenna Vertical Polarization Fixed Electrical Downtilt 4 4 V 8.5 TETRA/ TETRAPOL VPol Omni i 8.5 T Type No. Frequency range Polarization Gain Electrical tilt Impedance MHz Vertical 8 i 8.5, fixed 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). Grounding: The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is capacitively coupled. Omnidirectional 7 47 MHz maximum mast top Vertical Pattern 8.5 electrical downtilt Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8. kg 51 mm 22 N (at 15 km/h) 18 km/h 76 x 196 x 2 mm 114 mm Side-mounting brackets see cataloge part Mechanical Accessories 59

60 Omnidirectional Antenna Vertical Polarization V VPol Omni i Type No. Frequency range Polarization Gain Impedance MHz Vertical 8.5 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power 5 W (at 5 C ambient temperature) Radiator: Copper and brass. Radome: Fiberglass, colour: Grey. Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel. Mounting: The antenna can be attached laterally at the tip of any tubular mast of 5 94 mm diameter (connecting cable runs outside the mast). Omnidirectional 7 47 MHz Grounding: The antenna is DC grounded via a copper tube having a cross-sectional area of 22 mm 2. The inner conductor is coupled capacitively. maximum mast top Vertical Pattern Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height 7-16 female Bottom 8. kg 51 mm 22 N (at 15 km/h) 18 km/h 79 x 26 x 152 mm 11 mm 6 Side-mounting brackets see cataloge part Mechanical Accessories

61 Half-wave Dipole Side-mounted Vertical Polarization 8 47 V Omnidirectional antenna with variable antenna-to-mast distance. Depending on the distance of the radiator from the mast edge and also on the mast diameter, various radiation patterns can be achieved. VPol Omni i Type No. Frequency range Polarization Gain K MHz Vertical 4 i Impedance 5 Ω VSWR 4 47 MHz: < MHz: < 1.5; A = λ/4 8 4 MHz: < 2.; A > λ/4 Max. power 45 W (at 5 C ambient temperature) Attachment: Special features: Grounding: Horizontal radiation pattern: Radiator: Hot-dip galvanized steel. Horizontal support pipe: Stainless steel. Mount: Aluminum. Tightening band and all screws and nuts: Stainless steel. Feedpoint radome: Fiberglass. To tubular masts of 6 2 mm diameter using supplied stainless steel tightening band (2 mm wide,.8 mm gauge). The distance from tubular mast to radiator is adjustable from mm. All metal parts of the antenna including the inner conductor and the supplied mount are DC grounded. Depending on the distance A (edge of pipe mast to dipole) see sketch. Omnidirectional 7 47 MHz Mechanical specifications Distance A Abstand A For worked sample please refer to page 94 Input Weight Wind load Max. wind velocity Packing size Length N female 1.6 kg 4 N (at 15 km/h) 2 km/h 88 x x mm 15 mm Side-mounting brackets see cataloge part Mechanical Accessories 61

62 62

63 Summary Indoor Antennas Vertical Polarization Indoor Omnidirectional Antennas Single-band Type Type No. Height Input Page [mm] VPol Omni i N female 64 VPol Omni i N female 65 VPol Omni i N female 65 VPol Indoor i cable termination 66 VPol Omni i K N female 67 VPol Indoor i cable termination 68 Indoor Directional Antennas Single-band Type Type No. Height Input Page [mm] VPol Indoor i N female 69 VPol Indoor i 8 2 N female 69 New Products Kathrein Train Antennas a Solution also for Indoor Applications please refer to part Technical Information, page 9 Indoor 7 47 MHz 6

64 Omnidirectional Antenna Vertical Polarization 7 4 V TETRA/ TETRAPOL VPol Omni i Type No. Frequency range Polarization Gain Impedance MHz Vertical 2 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power W (at 5 C ambient temperature) Mounting: Grounding: Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. Indoor 7 47 MHz On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern 78 Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height N female Bottom 1. kg 21 mm 2 N (at 15 km/h) 2 km/h 112 x 97 x 654 mm 552 mm 64

65 Indoor Omnidirectional Antennas Vertical Polarization 8 4 V The antennas need no additional groundplane : VPol Indoor i 8 9: VPol Indoor i Type No Frequency range 8 45 MHz 45 4 MHz Polarization Vertical Vertical Gain Approx. 2 i Approx. 2 i Impedance 5 Ω 5 Ω VSWR < 2. < 2. Max. power Input 5 W (at 5 C ambient temperature) 1 x N female Protection class IP Weight Packing size Diameter Height 429 g 267 x 267 x 114 mm 258 mm 77 mm (without connector) Mounting: Grounding: Available accessories: Reflector: Aluminium. Radome: High impact polystyrol, colour: White. Additional painting is possible. Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 5 mm is required. All metal parts including the inner conductor are DC grounded. Power splitters (8 512 MHz) N connector, female Indoor 7 47 MHz holes 5 mm diameter 15. mm 1.6 mm 16 mm diameter 65

66 Indoor Omnidirectional Antenna Vertical Polarization 46 4 V VPol Indoor i Type No. Frequency range Polarization Gain Impedance MHz Vertical 2 i 5 Ω VSWR < 1.5 Max. power 5 W (at 5 C ambient temperature) Mounting: Grounding: Dipole: Brass. Radome: Fiberglass, colour: White. Additional mounting plate: Aluminum. a) Single-hole mounting (12 mm diameter) on surface of up to mm thickness. b) On surfaces of more than mm thickness, by means of mounting plate included in the scope of delivery. All metal parts of the antenna including the inner conductor are DC grounded. a) b) min. Ø 22 max. mm Ceiling Ceiling Indoor 7 47 MHz Ø 5,5 Mounting plate 9 Mechanical specifications Input Weight Radome diameter Mounting plate Packing size Height Cable RG 58/CU of 1 m length, grey, connector is not supplied.25 kg 2 mm 115 x 25 mm Foil: 65 x 1 mm 4 mm 66

67 Omnidirectional Antenna Vertical Polarization 7 47 V TETRA/ TETRAPOL VPol Omni i Type No. Frequency range Polarization Gain Impedance K MHz Vertical 2 i 5 Ω VSWR < 1.5 Intermodulation IM < 15 c (2 x 4 m carrier) Max. power W (at 5 C ambient temperature) Mounting: Grounding: Radiator: Brass. Radome: Fiberglass, dia. 21 mm, colour: Grey. Base: Aluminum. Mounting U-bolt and all screws and nuts: Stainless steel. The antenna can be attached in two ways with the supplied mounting kit: 1. On the tip of any tubular mast of 4 54 mm dia. (connecting cable runs inside the mast). 2. Laterally at the tip of any tubular mast of 2 54 mm dia. (connecting cable runs outside the mast). All metal parts of the antenna including the inner conductor are DC grounded. Indoor 7 47 MHz On the tip of a tubular mast Laterally at the tip of a tubular mast Vertical Pattern 78 Mechanical specifications Input Connector position Weight Radome diameter Wind load Max. wind velocity Packing size Height N female Bottom.8 kg 21 mm 2 N (at 15 km/h) 2 km/h 112 x 97 x 614 mm 5 mm 67

68 Indoor Omnidirectional Antenna Vertical Polarization V VPol Indoor i Type No. Frequency range Polarization Gain Impedance MHz Vertical 2 i 5 Ω VSWR < 1.5 Max. power 5 W (at 5 C ambient temperature) Mounting: Grounding: Dipole: Brass. Radome: Fiberglass, colour: White. Additional mounting plate: Aluminum. a) Single-hole mounting (12 mm diameter) on surface of up to mm thickness. b) On surfaces of more than mm thickness, by means of mounting plate included in the scope of delivery. All metal parts of the antenna including the inner conductor are DC grounded. a) b) min. Ø 22 max. mm Ceiling Ceiling Indoor 7 47 MHz Ø 5,5 Mounting plate 9 Mechanical specifications Input Weight Radome diameter Mounting plate Packing size Height Cable RG 58/CU of 1 m length, grey, connector is not supplied.2 kg 2 mm 115 x 25 mm Foil: 65 x 1 mm 6 mm 68

69 Indoor Directional Antenna Vertical Polarization Half-power Beam Width 8 4 V 9 TETRA/ TETRAPOL 8 278: VPol Indoor i 8 : VPol Indoor i Type No. Frequency range 8 45 MHz 45 4 MHz Polarization Vertical Vertical Gain Approx. 7 i Approx. 7 i Half-power beam width Horizontal: Approx. 9 Horizontal: Approx. 9 Impedance 5 Ω 5 Ω VSWR < 2. < 2. Max. power Input 5 W (at 5 C ambient temperature) N female connector Protection class IP Weight Packing size Height/width/depth g 15 x 252 x 62 mm 2 x 24 x 5 mm Mounting: Grounding: Available accessories: Reflector: Copper. Radome: High impact polystyrol, colour: White. Additional painting is possible. Mounting plates: Stainless steel. Two holes of 6 mm diameter in the mounting plate. Screws are not supplied All metal parts inclusive the inner conductor are DC grounded. Power splitters (8 512 MHz) Horizontal Pattern 9 Indoor 7 47 MHz Mounting: Mount the attachment plate to the wall using two screws of 4 mm diameter in the position as indicated. Align the antenna over the attachment plate. Pull the antenna down to the stop. 69

70 7

71 Summary Electrical Accessories 75 MHz Type Type No. Frequency Range Height Input Max. Power Page 2-way Splitter 75 MHz K MHz 95 mm N female 96 Watt MHz Type Type No. Frequency Range Height Input Max. Power Page 2-way Splitter 15 MHz K MHz 5 mm N female 68 Watt MHz Type Type No. Frequency Range Height Input Max. Power Page 2-way Splitter 45 MHz K MHz 49 mm N female 5 Watt 7 2-way Splitter 45 MHz K MHz 49 mm 7-16 female Watt 7 -way Splitter 45 MHz K MHz 49 mm N female 5 Watt 7 -way Splitter 45 MHz K MHz 49 mm 7-16 female Watt 7 4-way Splitter 45 MHz K MHz 49 mm N female 5 Watt 7 4-way Splitter 45 MHz K MHz 49 mm 7-16 female Watt 7 Filter products summary Combiners, Filters, Duplexers For detailed information see the catalogues Filters, Combiners, Amplifiers for Mobile Communications Electrical Accessories 71

72 Power Splitters For outdoor and indoor use. 2-way Splitter 75 2-way Splitter mm Type No. K K Connector (female) N N Max. power (at 5 C 96 W 68 W ambient temperature) For connecting... antennas 2 2 Frequency range MHz MHz VSWR < 1.1 < 1.1 Impedance 5 Ω 5 Ω Insertion loss <.5 <.5 Length L 95 mm 5 mm 2 mm L Protective case on the antenna side: Aluminum. Weather protectition on the equipment side: UV-resistant Elastomere. Transformation line: Aluminum and brass. All parts with protectition varnish. Mounting: On tubular masts of 6 2 mm dia. OD by means of non-corrosive clamp-strap (2 x 2 x 1 mm, supplied). Transformers with a total length of over 7 mm are delivered with a supporting clamp. Electrical Accessories Example for 2-way antenna splitter Antenna Antenna Equipment 72

73 Power Splitters For outdoor and indoor use. 2-way Splitter 9/42/45 -way Splitter 9/42/45 4-way Splitter 9/42/45 Type No. K K K K K K Connectors (female) N 7-16 N 7-16 N 7-16 Max. power 5 W W 5 W W 5 W W (at 5 C ambient temperature) For connecting... antennas 2 4 Frequency range MHz VSWR < 1.1 Impedance 5 Ω Insertion loss <.5 Packing size 425 x 9 x 7 mm Max. size 49 x 82 x 82 mm Mounting: Case: Aluminum. Inner conductor: Brass. Bracket for wall mounting included in the scope of supply. For mounting to tubular masts use clamps as listed below (order separately). K Clamps Type No. Description Mast Diameter Electrical Accessories clamps 55 mm clamps mm clamps mm clamps mm clamps mm

74 Filters, Duplexers, Combiners Band-pass Filter K MHz K MHz K MHz MHz MHz MHz MHz S-P Filter K K K K K MHz MHz MHz 8 47 MHz Duplexer MHz MHz MHz MHz MHz MHz K MHz K MHz K MHz K MHz K MHz K MHz (Tetra/Tetrapol) 8 85 / 9 95 MHz (Tetra/Tetrapol) / MHz (Tetra/Tetrapol) 85 9 / 95 4 MHz (Tetra/Tetrapol) / MHz (Tetra/Tetrapol) / MHz (Tetra/Tetrapol) / MHz (Tetra/Tetrapol) / MHz K K Hybrid Transmitter Combiner Electrical Accessories x W MHz x W 4 47 MHz (Tetra/Tetrapol) 4 x W 8 4 MHz Filter Transmitter Combiner x 5 W 42 4 MHz Multiband Combiner K / MHz / 8 47 MHz / 4 47 MHz / MHz / MHz / MHz (Tetra/Tetrapol) 8 4 / 4 4 MHz

75 Filters, Duplexers, Combiners - Coupler K K K MHz MHz MHz Hybrid Ring Junction K MHz K MHz K MHz 7 92 (Tetra/Tetrapol) 8 4 MHz Decoupled Power Splitter : MHz : MHz : MHz : MHz : 4 47 MHz : MHz (Tetra/Tetrapol) 1: 8 4 MHz (Tetra/Tetrapol) 1:4 8 4 MHz K K Circulator MHz MHz MHz MHz MHz (Tetra/Tetrapol) 8 4 MHz 78 6 DC-stop MHz 5-Ohm Loads male 1.5 W outdoor 4 MHz female 1.5 W outdoor 4 MHz K W 25 MHz K W 25 MHz K W 25 MHz K W 25 MHz K Electrical Accessories Receiver Multicoupler outputs MHz outputs MHz (Tetra/Tetrapol) 8 outputs 8 47 MHz (Tetra/Tetrapol) 16 outputs 8 47 MHz

76 76

77 Summary Mechanical Accessories Clamps, Downtilt Kits... Directional Antennas Dimensions 78 Clamps and Downtilt kits 8 Azimuth Adjustment Kit 85 Tools Azimuth Adjustment Tool 86 Brackets Page Bracket with Fixed Spacing 87 Bracket with Adjustable Spacing 87 Mechanical Accessories 77

78 Directional Antennas Dimensions VPol Panel 6 / 65 / 18 XPol Panel 65 A 49 mm 992 mm 198 mm B 49 mm 492 mm 485 mm C 29 mm 19 mm 19 mm D 4 mm 9 mm 185 mm XPol Panel 88 A 7 mm 1997 mm B 24 mm 5 mm C 28 mm 9 mm B A D Ø 11±,5 C A B C Top view Mechanical Accessories

79 Directional Antennas Eurocell Panels Antenna Dimensions VPol Panel 115 Eurocell Panel A 974 mm 194 mm 2574 mm B mm 199 mm 26 mm C 7 mm 2 mm 267 mm A B C Top view 258 Mechanical Accessories 79

80 Mounting Hardware for Directional Antennas VPol Panel 6 / XPol Panel 65 Mounting clamps/downtilt kit (order separately) Type No. Suitable for Weight (Pair of pipe masts of kg clamps)... mm diameter K K K K K Downtilt (to be used with a suitable pair of clamps for the individual mast diameter!) Antenna Height Downtilt Angle 992 mm mm 11 Pair of clamps K Weather-proof cover for elbow and straight connectors are supplied. Downtilt kit Mechanical Accessories straight elbow 8

81 Mounting Hardware for Directional Antennas XPol Panel 88 Special downtilt kit for Eurocell Panel antennas with a weight greater than 25 kg and for XPol Panel for Tetra Downtilt kit M supplied Type No. Preferred range of use 85 7 Panel antennas with a weight of 25 kg Panel antennas with attached mounting plates Downtilt kit without scale for universal use M8 supplied Weight 5.9 kg Material Hot-dip galvanized steel All screws and nuts Stainless steel Recommended mast clamps: Type No. Description Mast diameter Weight approx. Units per antenna clamp mm 1. kg clamp 1 22 mm 2.7 kg clamp 2 8 mm 4.8 kg 2 Recommended torque for all bolted connections: Screw size M8 M Torque 12 Nm 26 Nm Maximum acceptable load: Frontal wind load < 25 N Lateral wind load Antenna weight < 8 N 5 kg 64± Downtilt angle Antenna height Downtilt angle mm mm Mechanical Accessories 64±.5 22 M 81

82 2 15 Mounting Hardware for Directional Antennas VPol Panel 115 Downtilt kits Antenna Height: 974 mm 194 mm 258 Description Mast diameter Type No. Distance A Weight Units per mm approx. antenna Small Pipe mm * g see sketch Large Pipe mm kg see sketch 1 22 mm kg see sketch 2 8 mm kg see sketch Off-set mm kg see sketch mm kg see sketch 2 8 mm kg see sketch mm kg see sketch A Screws, washers and nuts supplied Use the downtilt kit together with the clamps mentioned above Scale Downtilt angle Mechanical Accessories Antenna Height Downtilt angle Type No. Weight 974 mm approx. 2.8 kg 194 mm approx. 2.8 kg Mounting a downtilt kit enlarges the spacing between mast and antenna by 84 mm. 82

83 Eurocell Panels Sector Panel Arrangement Mounting Hardware Sector Clamp Kit / Pipe Mast with Flange Base Slim and unobstrusive design Nearly cylindrical optical appearance with small outer diameter Sector Clamp Kit Type No Angle between antennas Suitable for mast diameter 114. mm 19.7 mm Type No. of pipe mast (please order separately) Number of pieces 2 x sector clamp 2 x sector clamp 2 x mounting support 2 x mounting support clamp clamp Material sector clamp Hot-dip galvanized steel Hot-dip galvanized steel Mounting support Aluminum Aluminum clamp Screws Stainless steel Stainless steel Outer diameter (D out ) of the Eurocell Panel Arrangement 419 mm 441 mm Weight Clamp kit. kg.2 kg sector clamp 1.4 kg 1.5 kg Only for Types ± sector clamp D out A C B F E D Torque 8 Nm Mounting support clamp Bottom view without downtilt kit Type No. A B C D E F all dimensions in mm D Pipe Mast with Flange Base Type No Pipe diameter D 114. mm 19.7 mm according DIN 2448 Wall thickness pipe 6. mm 4 mm Pipe length mm mm Flange diameter 2 mm 265 mm Flange thickness S 14 ± 1 mm 19 ± 1 mm Hole circle diameter 17 mm 225 mm Number of holes 6 6 Hole diameter 18 ± 1 mm 18 ± 1 mm Enclosed bolts thread x length M16 x mm M16 x mm Hot-dip galvanized steel Quality min. 8.8 Quality min. 8.8 Weight 6 kg 55 kg Material pipe mast S55 J2H (St 52-N) DIN EN 2-1 Material flange base S25 JR G2 (RSt 7-2) DIN EN 25 Maximum permissible load: According DIN 411 and DIN 412 Fatigue class K2 S ±1 129 ± Mechanical Accessories 8

84 Eurocell Panels Mounting Hardware 2 x C-Panel Mounting Kit Only for Eurocell Panels Use this mounting kit only for antennas less than 25 kg each. Type No No. of pieces 2 x brackets Suitable for A-/C-Panels 65, 9 with a max. height 2.6 m Clamp Hot-dip galvanized steel Screws Stainless steel Weight Approx.. kg Mounting Screws are supplied Recommended torque for M8 bolted connections: 12 Nm 4 9±1 64±.2 64±.2 64±.2 R 7 9±.5 28±.5 Mounting Accessories (order separately) Mechanical Accessories Clamps (only the listed clamps are allowed!) Type No. Description Remarks Weight Units per approx. antenna clamp Mast: 1 22 mm diameter 2.7 kg clamp Mast: 2 8 mm diameter 4.8 kg 2 Please chose the fitting downtilt kit that you need, from the antenna datasheet. 84

85 A-Panels / C-Panels / Eurocell Panels / F-Panels Mounting Hardware Azimuth Adjustment Kits Pole mounting Wall mounting Y X 58 8±1 Distance A see table 4 62± ±.5 18± The azimuth adjustment kit for pole mounting can be mounted with all suitable clamps, -Sector clamps and 2x A-/C-/F-Panel mounting kits (with the latter only as an interface between mounting kit and antenna). Type No Suitable for pole mounting wall mounting Number of pieces 2 brackets 2 brackets 2 brackets 2 brackets Distance between screws [A] 64 mm 72 mm 64 mm 72 mm Angular range ± ± Weight approx. 55 g approx. 7 g approx. 5 g approx. 12 g Supplied mounting all screws Screws and dowels for wall fastening are accessories not supplied, they must be chosen by installer according to on-site requirements. Materials Parts are hot-dip galvanized steel; Captive nuts are stainless steel Max. permissible static load / kit X direction 215 N 5 N 215 N 5 N Y direction 76 N 15 N 76 N 15 N Recommended torque for all supplied screws: 2 Nm, MoS 2 greased Mechanical Accessories 85

86 A-Panel / C-Panel / F-Panel / Eurocell Panel Accessories Azimuth Adjustment Tool Type No Precise azimuth adjustment for mast mounted antennas can easily be achieved by using the azimuth adjustment tool. This tool is suitable to all types of Eurocell Panels Panels A-Panels C-Panels F-Panels X-Pol F-Panels Target object Scale Target object Elevation compensation Move the stopper to central position* Panel Clamping device A-Panel F-Panel equivalent for 262 A-Panel F-Panel 199 F-Panel F-Panel 155 equivalent for F-Panel X-Pol-F-Panel F-Panel X-Pol-F-Panel Mechanical Accessories Instruction: Use a map to work out the angle between the designed antenna azimuth and target (church, building, mountain peak). Set this angle on the scale of the adjustment tool. Place the adjustment tool onto the antenna and tighten the clamping device. Use the telescope to aim at the target object, if necessary, use elevation compensation. Then rotate the antenna until the target object appears in the telescope. * Observe the position of the stopper when fitting the azimuth adjustment tool. 86

87 Accessories Stand-off Brackets When mounted to the tip of a mast, the antennas described in this catalogue radiate horizontally in a circular fashion. However, they can also be mounted laterally to a mast by using an extension bracket. Depending on the spacing and the mast diameter, various types of radiation patterns can be achieved. (For further information please see the Technical Information part of our catalogue on pages 94 and 95) Bracket with fixed spacing Type No. K K Weight Distance A: Suitable for antennas with a maximum wind load of Suitable for antennas with Attachment Material Wind load 2 kg 7 kg.2 kg 8.5 kg 5 mm mm 215 N (at 15 km/h) 85 N (at 15 km/h) mounting kit to pipe masts of 2 54 mm diameter. By means of mounting kit (supplied) to pipes of 55 mm 5 mm 55 mm 5 mm 5 mm 265 mm 5 mm 265 mm diameter Hot-dip galvanized steel. 6 N (at 15 km/h) 6 N (at 15 km/h) 515 mm K 61 K 61 4 pipe diameter 44.5 x 2.6 mm 15 mm pipe diameter 44.5 x 2.6 mm 95 Bracket with adjustable spacing A Implementation Stand-off Double stand-off fig. A fig. B fig. C A: mm D: 45 mm A D Type No. K K Weight 6.6 kg 1.7 kg 6 kg Distance A: min. 125 mm mm max. 68 mm 24 mm Suitable for antennas with mounting kit to pipe masts of 2 54 mm 9 mm 5 94 mm diameter diameter Attachment By means of mounting kit (supplied) to pipes of 55 mm 5 mm 4 5 mm diameter diameter Material Hot-dip galvanized steel. Wind load 45 N N 65 N (at 15 km/h) (at 15 km/h) (at 15 km/h) 74 mm 245 mm Double Bracket 125 to 68 mm 74 mm Pipe 48. x 2.6 mm ( mm length) free length 65 mm 4 x 4 mm 125 to 68 mm x 4 mm Pipe 76.1 x 2.6 mm free length 18 mm to 24 mm L x 4 Pipe 7 x 4 mm free length 25 mm 4 x 4 mm L x 4 fig. A fig. B fig. C 2 1 Mechanical Accessories 87

88 88

89 Summary of Technical Information Type Page Kathrein Train Antennas a Solution also for Indoor Applications 9 Antenna Systems with Panels K Examples of Radiation Patterns at 9 MHz with Combinations of Panels Examples of Radiation Patterns at 9 MHz with Combinations of Panels Radiation Patterns for Side-mounted Omnidirectional Antennas 94 Isolation Between Two Half-wave Dipoles 95 Isolation of Two Vertically Stacked Panels K Antenna Gain, VSWR / Reflected power 97 VSWR-reduction / Mismatch loss Technical Information

90 Kathrein Train Antennas a Solution also for Indoor Applications Kathrein train antennas has been implemented on indoor systems all over the world. Advantages: Sophisticated and robust design based on a fiberglass radome. Because of this rugged radome design, the antenna is well protected against vandalism. Low profile broadband antenna with small optical appearance. Especially in lower frequency applications, indoor antennas may have an unhandy size. This is due to the fact, that the antennas normally use a halfwave lambda radiator. Example: TETRA 9 MHz, antenna length roughly 4 mm. 14 mm Train antennas are based on quarterwave radiators resulting in conjunction with a special radiator design in very low lengths. The antenna for the range of MHz (see picture aside) is only 14 mm long! For a proper operation these antennas need an electrical counterweight or ground plane of a certain min. dimension. Mounting situation: The antennas has to be mounted on a conductive surface with dimensions according to the datasheet. This could be realized by a metallic sheet on the ceiling or directly by mounting the antenna on a metallic artificial ceiling. For a good contact one side of the antenna flange is not painted. Accordingly also the ground plane should be free of color in the area of mounting location. We strongly recommend to follow these specifications, otherwise the VSWR of the antenna will increase, destroying the performance of the antenna. Painting: The radome and base can be painted in any long-lasting color to match the surroundings. Suitable commercial paints consist of one or two components. The manufacturer s instruction for use and processing must be observed. Paints with metallic effects or metallic components are not permissible. Indoor system at the airport of Singapore with Kathrein train antennas Technical Information 9

91 Antenna Systems with Panels K Examples for radiation patterns at 16 MHz Arrangement Horizontal Technical Data Radiation Pattern Spacing A % rel. field strength corresponds to a gain* of A A 1 A 2 1 bay 2 bays.5 m m m Required components with conn. N female (without mounting kits): 2 antennas K , 2 junction cables K 62 21, 1 antenna transformer K Spacing A % rel. field strength corresponds to a gain* of 1 bay 2 bays.7 m m m Required components with conn. N female (without mounting kits): 2 antennas K , 2 junction cables K 62 21, 1 antenna transformer K Spacing A % rel. field strength corresponds to a gain* of A 1 bay 2 bays 1.4 m m m Required components with conn. N female (without mounting kits): antennas K , junction cables K 62 21, 1 antenna transformer K Spacing A % rel. field strength corresponds to a gain* of 1 bay 2 bays A m m m Required components with conn. N female (without mounting kits): 4 antennas K , 4 junction cables K 62 21, 1 antenna transformer K * ref. λ /2 dipole Vertical Radiation Pattern of the Arrangements 1,2, and 4 58 Vertical Radiation Pattern of the Arrangements 1,2, and Bay 2 Bays (Vertical spacing.96 λ = 1.8 m) 91 Technical Information

92 Examples of Radiation Patterns at 9 MHz with Combinations of Panels (XPol) Array Horizontal Radiation Pattern Technical Data 1 A Distance A % rel. field strenght corresponds to a gain of A.16 m 9.85 i.25 m 9.95 i.5 m 9.45 i 1.5 m 9.55 i 2 Distance A % rel. field strenght corresponds to a gain of A.2 m 7.75 i.5 m 8.15 i 1. m 7.85 i 2. m 7.95 i A Distance A % rel. field strenght corresponds to a gain of.16 m 5.85 i.22 m 5.75 i.65 m 6.55 i 1.1 m 6.5 i 4 Distance A % rel. field strenght corresponds to a gain of A.2 m 6.15 i.5 m 7.15 i.8 m 7.65 i 2.1 m 7.5 i Technical Information 92

93 Examples of Radiation Patterns at 9 MHz with Combinations of Panels (VPol) Array Horizontal Radiation Pattern Technical Data 1 A Distance A % rel. field strenght corresponds to a gain of A.25 m 9.55 i.5 m 9.5 i 1.5 m 9.85 i 2 Distance A % rel. field strenght corresponds to a gain of.5 m 8.5 i 1. m 7.75 i 2. m 8.5 i A A Distance A % rel. field strenght corresponds to a gain of.16 m 5.45 i.22 m 5.75 i.65 m 6.95 i 1.1 m 6.95 i 4 Distance A % rel. field strenght corresponds to a gain of A.5 m 6.85 i.8 m 7.5 i 2.1 m 7.45 i 9 Technical Information

94 Radiation Patterns for Side-mounted Omnidirectional Antennas Examples of horizontal radiation patterns for different mast diameters where A =.25 λ;.5 λ;.75 λ. Examples also apply for antenna K Distance A: Tubular mast Mast diameter Horizontal Radiation Pattern Antenna A 6 mm 16 mm A =.25 λ A =.5 λ A =.75 λ 25 mm 6 mm Triangular lattice mast A Antenna Triangular lattice mast with side length of 5 mm Technical Information 94

95 Isolation Between Two Half-wave Dipoles Isolation between two half-wave dipoles, vertically polarized and positioned vertically in line above each other on one common mast. Koppeldämpfung Isolation s d 15 λ/4,5,6,7,8,9 1, 1,1 1,2 1, 1,4 1,5 1,6 1,7 1,8 1,9 2, 2,1 2,2 2, Ratio: Distance (d) / wave-length (λ) Isolation between two vertically polarized half-wave dipoles mounted laterally Koppeldämpfung Isolation Koppeldämpfung Isolation d s Ratio: Distance (d) / wave-length (λ) Ratio: Distance (d) / wave-length (λ) 95 Technical Information

96 Isolation of Two Vertically Stacked Panels K 7 2. Isolation depends on vertical spacing A (at 45 MHz) 45 Isolation A Distance A/mm Technical Information 96

97 Antenna Gain, VSWR / Reflected power Antenna Gain in power ratio vs gain in 8 15 Gain in power ratio P1 / P G / = log P1 P2 Gain in power ratio P1 / P Gain in Gain in Voltage Standing Wave Ratio (VSWR) vs Reflected power Return loss (a r ) in Voltage Standing Wave Ratio (VSWR) s-1 s = 1+r = + P/%, r = s+1 s r - P/% s + 1 a r (in ) = - 2 log r P (in %) = ( r) 2 = a r/2 Reflected power P (in %) =. Forward power s = VSWR, r = Reflection coefficient a r = Return loss Reflected power P (in %) = Forward power Reflection coefficient (r) 97 Technical Information

98 VSWR-reduction / Mismatch loss Reduction of VSWR as a result of feeder cable attenuation 1.6 Cable loss VSWR at antenna end of feeder cable B 1.1 Feeder cable A VSWR at input to feeder cable (A) Mismatch loss vs VSWR Voltage Standing Wave Ratio (VSWR) Technical Information Mismatch loss in

99 Fax: central.sales@kathrein.de Technical Information: Fax: antennas.mobilcom@kathrein.de Internet: KATHREIN-Werke KG. Phone Fax Anton-Kathrein-Straße 1. P.O. Box D-84 Rosenheim. Germany Subject to alteration. Sales queries, orders, catalogues or CD-ROM: /27/5/ZW/MM Please contact for