FEDERAL COMMUNICATIONS COMMISSION (FCC) COMPLIANCE STUDY ON TELECOMMUNICATION FACILITY

Size: px

Start display at page:

Download "FEDERAL COMMUNICATIONS COMMISSION (FCC) COMPLIANCE STUDY ON TELECOMMUNICATION FACILITY"

Rosalind Parrish
5 years ago
Views:

1 FEDERAL COMMUNICATIONS COMMISSION (FCC) COMPLIANCE STUDY ON TELECOMMUNICATION FACILITY Prepared for: Site No.: CA-SAC112 EAST ARDEN 5107 FAIR OAKS BOULEVARD CARMICHAEL, CA SEPTEMBER 26/07, REV. 0

2 CA-SAC112 East Arden September 26, 2007, Rev. 0 Page 1 SITE DESCRIPTION: Carrier: Clearwire wireless broadband Site Address: 5107 Fair Oaks Boulevard, Carmichael, CA Type of Service: MMDS (Multichannel Multipoint Distribution Service) Sectors: 0, 120, 240 Antenna Type: Kathrein Number of Antennas: 3 Frequencies (GHz): Maximum Power: 64 W ERP (per sector) Antenna Height: 30 ± (Radiation center AGL) Table 1. Clearwire RF summary Clearwire is proposing to install three directional antennas on the rooftop (Figure 1) of an existing commercial building at the above address. Each antenna will have horizontal beam width of 87. The equipment cabinet will be installed on grade on the north side of the building. Only authorized personnel are allowed to access the rooftop. Figure 1. Facility and surrounding area

3 CA-SAC112 East Arden September 26, 2007, Rev. 0 Page 2 Clearwire also proposes to install three point-to-point microwave antennas on the rooftop. Each microwave antenna has a beam width of 1.7 and maximum output power of 199W ERP. Since the RF power outside the main beam of these microwave antennas is negligible (see antenna HP2-23 beam pattern in Appendix), the RF exposure contribution at ground level from the microwave dishes is insignificant. There are also two existing telecommunication facilities (MetroPCS and SureWest) with antennas mounted on the rooftop of the same building. The RF summary for the existing facilities is shown in the following Tables. Carrier: metropcs Type of Service: 1900MHz CDMA (Broadband PCS) Antenna Type: Allgon 7721 Number of Antennas: 3 (1 per sector) Maximum Power: 500 W (Maximum ERP per sector) Antenna Height: 25 ± (Radiation center AGL) Table 2. metropcs RF summary Carrier: SureWest Wireless Type of Service: PCS CDMA (1900 MHz) Antenna Quantity: 3 (1 per sector) Antenna Type: EMS RR65-18-xxDPL2 (typical) Maximum Power: 500 W ERP per sector (typical) Antenna Height: 30 ± (Radiation center AGL) Table 3. SureWest Wireless RF summary PROTOCOL: This study, and the calculations performed therein, is based on OET Bulletin 65 1 which adopts ANSI C and NCRP standards. In particular, equation 10 from section 2 of the guideline is used as a model (in conjunction with known antenna radiation patterns) for calculating the power density at different points of interest. This information will be used to judge the RF exposure level incident upon the general population, and any employee present in the area. It should be noted that ground reflection of RF waves has been taken into account. ENVIRONMENTAL EVALUATION: According to Table 2 in Appendix A of Bulletin 65, an MDS facility is subject to routine environmental evaluation if the total power of all channels in a given sector is in excess of 1000 W ERP. The maximum ERP of the facility is 64W; therefore, this facility is exempt from routine environmental evaluation. FCC S MAXIMUM PERMISSIBLE EXPOSURE (MPE) LIMIT: In order to evaluate the RF exposure level, the power densities at different locations of interest have been examined. Equation 10 from Bulletin 65 is reproduced here as equation 1: 1 Cleveland, Robert F, et al. Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields. OET Bulletin 65, Edition 97-01, August 1997.

4 CA-SAC112 East Arden September 26, 2007, Rev. 0 Page F ERP S = (1) 2 R Where: S = Power density [μw/cm 2 ] ERP = Effective radiated power [W] R = Distance [m] F = Relative field factor (relative numeric gain) Scenario 1: Standing near the facility The RF exposure level of a six-foot tall person standing close to the building is evaluated. For the worst-case scenario, the cumulative power densities from all the existing and the proposed carriers are considered. We assume that all the antennas are transmitting the maximum number of channels at the same time, with each channel at its maximum power level. In addition, the azimuths of the antennas are assumed to be in the direction of the studied location. Please refer to scenario 1 in appendix A for the complete geometry and analysis. The highest exposure location is approximately 136 from the building. The calculations of maximum cumulative power density are summarized in Table 4. Service Max. ERP F 2 R (m) S (μw/cm²) (from eq. 1) MPE % clearwire 64 W 0 db (1) metropcs 500 W -10 db (0.1) SureWest 500 W -13 db (0.05) Total Table 4. Worst-case predicted power density values for scenario 1. The Maximum Permissible Exposure (MPE) limit for 1900 MHz and 2500 MHz facilities 2 for general population/uncontrolled exposure is 1000 μw/cm². The maximum cumulative power density for the proposed Clearwire antennas and the existing antennas is calculated to be 0.26% of the MPE limit. Scenario 2: Nearby Rooftops There are low-rise residential and commercial buildings in the surrounding area. There is also an existing monopole with telecommunication facilities located approximately 500 southeast of the proposed clearwire facility. Two levels of directional antennas are installed on the monopole. The RF exposure levels on the neighboring rooftops are evaluated. Please refer to scenario 2 in appendix A for the analysis. We assume again, all antennas within a sector are transmitting with maximum power level and the antennas have similar azimuths. Service Max. ERP F 2 R (m) S (μw/cm²) (from eq. 1) MPE % clearwire 64 W 0 db (1) SureWest 500 W 0 db (1) MHz facility 500 W 0 db (1) MHz facilities 1000 W 0 db (1) Total Table 5. Worst-case predicted power density values for scenario 2. 2 Ibid., page 67.

7 SCENARIO 1 NEAR FACILITY APPENDIX A SITE NAME: East Arden SITE NUMBER: CA-SAC112 Ө = 30 degrees Person = 6 feet Carrier Height (feet) Horz. Dist. (feet) R (feet) R (meters) Ө (degrees) clearwire metropcs SureWest Carrier F² (db) Max. ERP S (μw/cm²) MPE (%) clearwire metropcs SureWest S total Ө = 15 degrees Person = 6 feet Carrier Height (feet) Horz. Dist. (feet) R (feet) R (meters) Ө (degrees) clearwire metropcs SureWest Carrier F² (db) Max. ERP S (μw/cm²) MPE (%) clearwire metropcs SureWest S total Ө = 10 degrees Person = 6 feet Carrier Height (feet) Horz. Dist. (feet) R (feet) R (meters) Ө (degrees) clearwire metropcs SureWest Carrier F² (db) Max. ERP S (μw/cm²) MPE (%) clearwire metropcs SureWest S total

8 SCENARIO 2 NEARBY ROOFTOPS Sector A Person = 6 feet Building = 18 feet Carrier Height (feet) Horz. Dist. (feet) R (feet) R (meters) Ө (degrees) clearwire Surewest MHz facility MHz facilities Carrier F² (db) Max. ERP S (μw/cm²) MPE (%) clearwire Surewest MHz facility MHz facilities metropcs antenna azimuths not the same as clearwire S total Sector B Person = 6 feet Building = 16 feet Carrier Height (feet) Horz. Dist. (feet) R (feet) R (meters) Ө (degrees) clearwire Surewest MHz facility MHz facilities Carrier F² (db) Max. ERP S (μw/cm²) MPE (%) clearwire Surewest MHz facility MHz facilities S total 0.722

9 Sector C Person = 6 feet Building = 16 feet Carrier Height (feet) Horz. Dist. (feet) R (feet) R (meters) Ө (degrees) clearwire Surewest MHz facility MHz facilities Carrier F² (db) Max. ERP S (μw/cm²) MPE (%) clearwire Surewest MHz facility MHz facilities S total

Kathrein Scala s X-polarized adjustable electrical downtilt antennas offer the carrier the ability to tailor sites for optimum performance.

0-10 electrical downtilt range. DC Grounded metallic parts for impulse suppression. No moving electrical connections. Optional remote downtilt control.

10 Kathrein Scala s X-polarized adjustable electrical downtilt antennas offer the carrier the ability to tailor sites for optimum performance. Using variable downtilt, only a few models need be procured to accommodate the needs of widely varying conditions. Remotely controlled downtilt is available as a retrofitable option electrical downtilt range. DC Grounded metallic parts for impulse suppression. No moving electrical connections. Optional remote downtilt control Panel Antenna MHz Specifications: Frequency range MHz Gain 16 dbi Impedance 50 ohms VSWR < 1.5:1 Intermodulation (2x20w) IM3:< -150 dbc Polarization +45 and -45 Front-to-back ratio >23 db typical Maximum input power 300 watts (at 50 C) H-plane beamwidth 87 degrees at midband (half power) E-plane beamwidth 7 degrees at midband (half power) Electrical downtilt 0 10 degrees continously adjustable Connector N or 7/16 DIN female Sidelobe suppression for first sidelobe above horizon db (typical) Null fill > -1 dbi to 12 below horizon (typical) (17 db below 16 dbi main beam) Weight 10 lb (4.5 kg) Dimensions 42 x 6.1 x 2.7 inches (1067 x 155 x 69 mm) Equivalent flat plate area 2.5 ft 2 (0.23 m 2 ) Wind survival rating* 120 mph (200 kph) Shipping dimensions 48 x 6.8 x 3.6 inches (1220 x 172 x 92 mm) Shipping weight 13.6 lb (6.2 kg) Mounting Fixed and tilt-mount options are available for 2 to 5.7 inch (50 to 145 mm) OD masts. See reverse for order information. * Mechanical design is based on environmental conditions as stipulated in EIA-222-F (June 1996) and/or ETS which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details H-plane Horizontal pattern ±45 - polarization 0 electrical downtilt H-plane Horizontal pattern ±45 - polarization 5 electrical downtilt H-plane Horizontal pattern ±45 - polarization 10 electrical downtilt E-plane Vertical pattern ±45 - polarization 0 electrical downtilt E-plane Vertical pattern ±45 - polarization 5 electrical downtilt E-plane Vertical pattern ±45 - polarization 10 electrical downtilt A Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR (USA) Phone: (541) Fax: (541) communications@kathrein.com Internet:

23 GHZ (21.2-23.6) HIGH-PERFORMANCE MICROWAVE ANTENNAS FEATURES Antenna diameters 1' (30 cm) 1.5' (45 cm) 2' (60 cm) 3' (90 cm) 4' (120 cm) Antenna weights 1' 17 lbs. (7.7 kg) 1.5' 19 lbs. (8.

11 23 GHZ ( ) HIGH-PERFORMANCE MICROWAVE ANTENNAS FEATURES Antenna diameters 1' (30 cm) 1.5' (45 cm) 2' (60 cm) 3' (90 cm) 4' (120 cm) Antenna weights 1' 17 lbs. (7.7 kg) 1.5' 19 lbs. (8.6 kg) 2' 27 lbs. (12.2 kg) 3' 50 lbs. (22.5 kg) 4' 85 lbs. (38.3 kg) HP models: high-performance, plane polarized HPD models: dual polarized IEC or EIA flanges available Direct mounting for RF units available Ease of installation: antennas shipped completely assembled, minimal mount required Planar radomes standard with high-performance model Rugged and lightweight cast aluminum mount with fine adjustment for both azimuth and elevation Compact size, due to Radio Waves innovative feed design Standard white; other colors and/or logos available on request Corrosive resistant: coated aluminum, hot dipped galvanized steel and stainless steel Three year warranty GHZ ELECTRICAL SPECIFICATIONS (typical performance)* Model Diameter Gain, dbi Beamwidth X Pol. F/B VSWR Max. Number ft (cm) Low Mid High Degrees, 3dB Disc., db Ratio, db (R.L., db) Plane Polarized HPLP (30) :1 (15.5) HPLP (45) :1 (15.5) HP (60) :1 (15.5) HP (90) :1 (15.5) HP (120) :1 (15.5) Dual Polarized HPLPD (30) :1 (15.5) HPLPD (45) :1 (15.5) HPD (60) :1 (15.5) HPD (90) :1 (15.5) HPD (120) :1 (15.5) * All specifications subject to change without notice. For regulatory compliances, contact Radio Waves. Radio Waves, Inc. PROLINE ANTENNAS

7721.00 UXM-1710-2170-65-18i-A-D Electrical Specifications Gain 16dBd ( 18dBi ) Polarization linear, dual slant +/-45 VSWR, 50Ω <1.

13 UXM i-A-D Electrical Specifications Gain 16dBd ( 18dBi ) Polarization linear, dual slant +/-45 VSWR, 50Ω <1.4:1 Horizontal 3dB beamwidth 65 Vertical 3dB beamwidth 7 Electrical downtilt 0-8 Front-to-back ratio >30 db co-polar Suppression of first upper side lobe > 18dB for 0-3 degrees First lower null fill >-18 db typical Average input power 250W per connector 500W total Two tone intermodulation 3rd order < -107dBm for 2x20W 2x43dBm) Isolation between ports >30dB Mechanical Specifications Connector 7/16 DIN bottom mount Height 51.3" (1309 mm) Width 6.6" (167 mm) Depth 3.5" (89.5 mm) Survival wind speed 156mph ( 70m/s ) Maximum wind area 2.3 sq. ft.(0.22 sq. m) Frontal wind 100mph 70 lbf (310N) *All feed network components DC grounded for Lightning Protection Mounting Hardware Premounted for Installation Mounting diameter range 1" to 5" OD Mechanical downtilt range -0.6 to Horizontal Pattern Vertical Pattern

DUALPOL PRODUCT DATA SHEETS Electrical Specifications Azimuth Beamwidth (-3 db) Elevation Beamwidth(-3 db) Elevation Sidelobes (Upper) Gain Polarization Port-to-Port Isolation Front-to-Back Ratio

4 dbd) Dual Linear Slant (± 45 ) 30 db 30 db 0, 2, 4, 6 1.

14 DUALPOL PRODUCT DATA SHEETS Electrical Specifications Azimuth Beamwidth (-3 db) Elevation Beamwidth(-3 db) Elevation Sidelobes (Upper) Gain Polarization Port-to-Port Isolation Front-to-Back Ratio Electrical Downtilt Options VSWR Connectors Power Handling Passive Intermodulation Lightning Protection RR65-18-XXDPL2 DualPol Polarization 1850 MHz MHz db 17.5 dbi (15.4 dbd) Dual Linear Slant (± 45 ) 30 db 30 db 0, 2, 4, :1 Max 2; 7-16 DIN (female) 250 Watts CW -150 dbc [2 x 20 W (+ 43 dbm)] Chassis Ground OptiRange Suppressor Mechanical Specifications Dimensions (L x W x D) Rated Wind Velocity Equivalent Flat Plate Area Front Wind 100 mph (161 kph) Side Wind 100 mph (161 kph) Weight 56 in x 8 in x 2.75 in (142 cm x 20.3 cm x 7.0 cm) 150 mph (241 km/hr) 3.1ft 2 (.29 m 2 ) 90 lbs (400 N) 31 lbs (139 N) 18 lbs (8.2 kg) Mounting Options MTG-P00-10, MTG-S02-10, MTG-DXX-20*, MTG-CXX-10*, MTG-C02-10, MTG-TXX-10* Note: *Model number shown represents a series of products. See Mounting Options section for specific model number. Patterns Azimuth Elevation 0 Downtilt Elevation 2 Downtilt Elevation 4 Downtilt Elevation 6 Downtilt Revised 04/05/ ext Fax

NON-IONIZING ELECTROMAGNETIC EXPOSURE ANALYSIS & ENGINEERING CERTIFICATION

NON-IONIZING ELECTROMAGNETIC EXPOSURE ANALYSIS & ENGINEERING CERTIFICATION SITE NAME: SEA Dutch Cup SITE ADDRESS: 1102 E Main Street Sultan, WA 98294 DATE: June 2, 2017 PREPARED BY: B. J. THOMAS, P.E.