MHz. ANT150D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dbd

Size: px

Start display at page:

Download "MHz. ANT150D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dbd"

Carmella Priscilla Lester
5 years ago
Views:

138-174 MHz ANTD, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dbd The Telewave ANTD series consists of single, dual, and 4-element di pole array antennas with a precision phasing harness for optimum per

1 MHz ANTD, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dbd The Telewave ANTD series consists of single, dual, and 4-element di pole array antennas with a precision phasing harness for optimum per formance. The horizontal pattern is fieldadjustable for any current or future cov er age requirements. The wide bandwidth and high efficiency of these antennas make them ideal for applications including trunking, business, public safety, and amateur radio. Each dipole element is constructed with 61-T6 aluminum, and welded at the base for maximum strength. Each element is also completely sealed with our high-tech Txylan coating, which resists water and ice buildup, and provides exceptional protection from corrosive gases, UV radiation, salt spray, acid rain and windblown abrasives. The phasing harness is fully sealed by Telewave s Millenium Seal technology. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a diameter galvanized steel support pipe or tower leg. Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included with the order, and consultation with our antenna engineering staff is requested. H-Plane: Gain 9.1 dbd 1/4 wl. spacing from tower H-Plane: Gain 9.1 dbd 1/2 wl. spacing from tower H-Plane: Gain 8.5 dbd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) MHz Lightning protection DC Ground Power rating (typ.) 5 watts Wind rating 175 MPH Impedance 5 ohms (with.5 ice) MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL ANTD ANTD3 ANTD6-9 Gain (dependent on pattern) dbd 3-6 dbd 6-9 dbd Vertical beamwidth (3/8 wl.) Dimensions (H x D) max. 34 x 36 in. 89 x 36 in. 195 x 36 in. Weight (antenna + clamps) 5 lb. 13 lb. 28 lb. Maximum exposed area.73 ft.² 1.6 ft.² 3.3 ft.² Lateral thrust at 1 MPH 29 lbs 64 lbs 134 lbs Electrical uptilt or downtilt N/A ANTD6-9 (Harness not shown) Support mast is customer-supplied TWDS-745 Rev. 11/8

2 - MHz DIPOLE PATTERN ADJUSTMENT Telewave folded dipoles are field adjustable to provide different horizontal patterns and gain values. The horizontal spacing from tower between the dipole and the support mast or tower leg controls this adjustment. Review the patterns below to determine which is best suited to your range area re quire ments. Use the chart on the next page to find the appropriate dimension for antenna to mast spacing. The draw ing at the bottom shows how this mea sure ment is made and the vertical spacing to be used for multi-element arrays. Horizontal radiation patterns Offset Circular 1/4 wavelength spacing Cardioid 3/8 wavelength spacing Bi-directional 1/2 wavelength spacing Mast Extension Pattern Spacing Measured distance from the face of the mast to the middle of the dipole loop. Vertical spacing Mast Extension Drain Holes IMPORTANT: Be sure that the drain holes are on the bottom when the elements are installed. TWDS-757 Rev. 1/8

3 - MHz DIPOLE PATTERN ADJUSTMENT DIPOLE MOUNTING AND MAST SPECIFICATIONS Mast lengths shown are minimum acceptable lengths to insure proper pattern control. Mast extension is applied at top and bottom of array. Longer masts are acceptable, but the dipole or array must be centered on the support to prevent beam tilt. The clamps provided with the dipoles will work properly to attach the dipole boom to a mast that is between 1.5 to 2.5 inches in diameter. To attach to smaller supports (1-1.5 diameter), use ANTS42 shims. This allows direct mount ing to small towers such as the Rohn 25 and 45. MAST MINIMUM LENGTH AND ELEMENT VERTICAL SPACING (at midband) ANTENNA MAST LENGTH MAST EXTENSION VERTICAL SPACING MINIMUM MAST TYPE ANT37D ANT4D CONTACT TELEWAVE FOR MOUNTING ADVICE ANT5D ANT7D 6'-7 3'.5 N/A 2. Schedule 4 Galvanized Pipe ANT75D 6'-7 3'.5 N/A 2. Schedule 4 Galvanized Pipe ANT75D3 15' 4' Schedule 4 Galvanized Pipe ANTD 5'-6 2'-9 N/A 2. Schedule 4 Galvanized Pipe ANTD3 12'-2 2' Schedule 4 Galvanized Pipe ANTD 4'-2 2'-1 N/A 1.5 Schedule 4 Galvanized Pipe ANTD3 1' 2' Schedule 4 Galvanized Pipe ANTD Schedule 4 Galvanized Pipe ANTD 3' 18 N/A 1.5 Schedule 4 Galvanized Pipe ANTD3 7' Schedule 4 Galvanized Pipe ANTD6-9 16' Schedule 4 Galvanized Pipe ANTD ' Schedule 4 Galvanized Pipe ANT22D 2'-4 14 N/A 1.5 Schedule 4 Galvanized Pipe ANT22D3 5' Schedule 4 Galvanized Pipe ANT22D6-9 11' Schedule 4 Galvanized Pipe ANT275D 2' 12 N/A 1.5 Schedule 4 Galvanized Pipe ANT275D3 4' Schedule 4 Galvanized Pipe ANT275D Schedule 4 Galvanized Pipe ELEMENT HORIZONTAL SPACING FROM TOWER (at midband) MODEL 1/4 wl. OFFSET CIRCULAR 3/8 wl. CARDIOID 1/2 wl. BI-DIRECTIONAL ANT37D 6 N/A N/A ANT4D 5-9 N/A N/A ANT5D N/A ANT7D 3 5 MAX EXTENSION ANT75D, D MAX EXTENSION ANTD, D ANTD, D3, D ANTD, D3, D6-9, D ANT22D, D3, D ANT275D, D3, D NOTE: The physical characteristics of large dipoles require a correction factor from calculated values for mast spacing. The dimensions in the above table include this correction. TWDS-757 Rev. 1/8

4 ANTENNA MOUNTING BOLTS (4) MOUNTING CLAMP "A" MOUNTING CLAMP "B" MOUNTING PLATE JAM BOLTS (2) JAM BOLTS DIPOLE BOOM (END VIEW) SUPPORT MAST OR TOWER TELEWAVE, INC. DIPOLE MOUNTING DIAGRAM ANT7D-75D-D TWDS-764 Rev. 9/8

5 FOLDED DIPOLE ANTENNAS MHz MOUNTING INSTRUCTIONS ASSEMBLY INSTRUCTIONS 1. Remove components from shipping box and lay out the dipole and cable assemblies, ideally in a large, sheltered area. Arrange the assemblies in order as cable lengths allow WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. PARTS LIST (for single dipole element): (1) Dipole and clamp set (1) 1/4 hex bolt (1) 1/4 lock nut (2) 3/8 x 3.5 hex bolt (2) 3/8 hex nut (2) 3/8 split lock washer (1) Anti-seize compound Refer to the diagram. Slide the boom over the dipole hub, and align the holes in the boom with the holes in the hub. Apply anti-seize compound to the bolt end, then install and tighten the 1/4" bolt and lock nut. Press the end plug located on the dipole feed cable into the end of the boom until it is firmly seated. Refer to the appropriate Dipole Pattern Adjustment sheet for the frequency range of the antenna. Using the chart titled "Dipole Mounting and Mast Specifications", measure and mark the support structure for the proper dipole element spacing. Mount each dipole assembly to the mast with clamps as shown in the diagram. Locate the drain hole on each element, and be certain it is pointing down. Refer to the chart titled "Mast to Dipole Dimensions", and determine the proper horizontal element spacing from the mast or support structure for the desired coverage pattern. At least 1/2 inch of the boom should be visible on the back side of the clamps. Apply anti-seize compound to the bolt ends, then secure the dipole assemblies to the support with the supplied 3/8" nuts, washers and bolts, while adjusting each dipole position on the support. Tighten each nut until the lock washer is flat, then add 1/2 turn. Be sure to properly seal the input connector with waterproof tape or other sealing material. See Telewave TWDS-52 for a recommended method of connector sealing. Secure the cable assembly to the support. 1/2 inch of the boom visible Dipole Element Clamp Assemblies Boom Dipole Hub 1/4" Bolt / Nut Phasing Harness Drain Holes End Plug Drain Hole Coax TWDS-789 Rev. 3/11

6 Effective July 213 SECTION 7 ANTENNAS BASE STATION ANTENNAS MHz DIPOLES AND DIPOLE ARRAYS 5 WATTS ADJUSTABLE PAT TERNS Standard connector is N-Male on a pigtail* DIN available (additional cost). All dipoles and arrays are fi eldconfi gurable and UPS shippable (except 37D, 4D, 42D, 5D), and include clamps for mounting to an existing mast or other support. One support boom with clamps is included with models from MHz. 2 and 4 bay arrays can be ordered with up to 15 degrees of electrical uptilt or downtilt. MODEL ANT37D* FREQ. RANGE BAYS GAIN MHz INSTALLED HEIGHT SHIP WEIGHT LIST PRICE 145" 8 lb $2, ANT4D* MHz 129" 74 lb $2,194.5 ANT42D* MHz 1 1 to 2.6 dbd 126" 55 lb $1,.56 ANT44D* MHz " 46 lb $1,894. ANT5D MHz 18" 69 lb $2,296.8 ANT7D MHz 76" 36 lb $1, to 2.6 dbd ANT75D MHz 72 lb $1,23. ANTD 888 MHz lb $1, to 2.6 dbd ANTD MHz 45 9 lb $433.4 ANTD 1 1 to 2.6 dbd 34 8 lb $43.7 ANTD3 2 3 to 6 dbd lb $ MHz ANTD to 9 dbd lb $1,44.7 ANTD to 12 dbd lb $2,87.2 ANT22D 1 1 to 2.6 dbd 23 8 lb $4.1 ANT22D3 2 3 to 6 dbd 61 2 lb $ MHz ANT22D to 9 dbd lb $1,444. ANT22D to 12 dbd 64 lb $2,884.2 ANT275D 1 1 to 2.6 dbd 19 8 lb $443. ANT275D3 2 3 to 6 dbd lb $ MHz ANT275D to 9 dbd 115 lb $1,42.1 ANT275D to 12 dbd 22 lb $2,84.2 ANT35D 1 1 to 2.6 dbd 17 7 lb $4.1 ANT35D3 2 3 to 6 dbd lb $7.4 MHz ANT35D to 9 dbd lb $1,259.5 ANT35D to 12 dbd lb $2,52.1 ANT375D 1 1 to 2.6 dbd 15 7 lb $319. ANT375D3 2 3 to 6 dbd lb $ MHz ANT375D to 9 dbd lb $1,259.5 ANT375D to 12 dbd lb $2,52.1 * 8 bay arrays terminate with N-Female or DIN-F on power divider. ANT37D, 4D, 42D, and 5D ship via truck. 44

Model VB-23FM 2-Meter 3-Element Beam

308 Industrial Park Road Starkville, MS 39759 USA Ph: (662) 323-9538 FAX: (662) Model VB-23FM 2-Meter 3-Element Beam [ INSTRUCTION MANUAL Figure 1 Overall View and Boom Detail GENERAL DESCRIPTION This