MOSFET BASED DC SOLID-STATE RELAY. In & case / Out Insulation. Fig. 2. Please consult us to select the right protective components C1, D1 & D2.

Transcription

1 Page 1/5 UK MOSFET BASED DC SOLID-STATE RELAY SCM Latest MOSFET technology generation. Ultra low on-state resistance. New innovative isolated driver ensuring fast power transistor turn on and off therefore low power transient. Ultra low output leakage current Low control current consumption Triggered control input to avoid linear control risks Low conducted and radiated disturbances Control range Max transient peak Advised max. DC Mains peak Max. Load Current (with heatsink) VDC 100V Depend on the protection 150ADC DC Mains range Load current range Control input range In & case / Out Insulation Connections Dimensions (WxHxD) Weight (Depends on protection clamping ) 0 to 150A (with heatsink) VDC 4kV M3 round tabs M5 round tabs 44.5 x 58.2 x 27 (mm) 100g Fig. 1 HIGH SIDE WIRING DIAGRAM (Load connected to - ) Fig. 2 LOW SIDE WIRING DIAGRAM (Load connected to + ) Please consult us to select the right protective components C1, D1 & D2. Please consult us to select the right protective components C1, D1 & D2. The red paths (C1/D1/D2) must be as short as possible! The red paths (C1/D1/D2) must be as short as possible! Fig. 3 INTERNAL DIAGRAM Proud to serve you Data given at Tambient=25 C and subject to modification without previous notice

2 POWER CIRCUIT TIME CHARACT. INPUT CIRCUIT Page 2/5 UK CONTROL INPUT CHARACTERISTICS CHARACTERISTIC LABEL VALUE INFO. Fig. 4 Nom. Control Ucnom 12-24VDC Nom. Control current Icnom 35mADC Control range Uc VDC typical=4.3v Control current consumption Ic 25 42mADC See curve Releasing control Ucoffmax 1VDC Typical= 3.5V Max. reverse control Input impedance -Ucmax 32VDC -Icmax <100µA Rin Current limitation See curve Ic (madc) CONTROL CURRENT vs. CONTROL C Uc (VDC) TIME CHARACTERISTICS CHARACTERISTIC LABEL VALUE Turn on time ton 10µs Turn on delay tdon 600µs Turn off time toff 10µs Turn off delay tdoff 100µs Max. On-Off frequency F(on-off) 700Hz POWER OUTPUT CHARACTERISTICS CHARACTERISTIC LABEL VALUE INFO. Mains range Ut Ue Min = RDSon x Ie Non-repetitive peak Utp 100V Over protection Off-state max reverse drop (internal diode) Maximum nominal currents D1 Not integrated A clamping mean must be connected across the terminals 1 & 2 (see fig 1 & 2) -Ut 0.7V Ie max Resistive 150A Max. non-repetitive peak current Iepeak 390A Min. load current Iemin 0mA Motor Please contact us Depends on protection clamping (D1) Please consult us to select the right See fig. (See fig. 8) Max. leakage current Ielk Max. on-state resistance RDSon C Typ. output capacitance Cout Junction/case thermal resistance Rthjc 0.59K/W Built-in heatsink thermal resistance vertically mounted Rthra Tra=75 C Heatsink thermal time constant Tthra 10 Tra=60 C Control inputs/power outputs insulation Uimp Inputs/case insulation Uimp 4kV Outputs/case insulation Uimp 4kV Isolation resistance Rio 1G Isolation capacitance Cio <8pF Maximum junction temperature Tjmax 175 C Storage ambient temperature Tstg -40->+100 C Operating ambient temperature Tamb -40->+90 C See fig. 9 Max. case temperature Tc 100 C 4kV

3 Page 3/5 UK OUTPUT SWITCH CHARACTERISTIC CURVES Fig. 5 ON RESISTANCE VS JUNCTION TEMPERATURE Fig. 6 REVERSE VOLTAGE DROP VS REVERSE CURRENT Fig. 7 POWER ELEMENT TRANSIENT THERMAL IMPEDANCE vs. PULSE DURATION Fig. 8 ON-STATE PEAK OVERLOAD CURRENT vs. PULSE DURATION Fig. 9 Permanent current Ie (ARMS) POWER DISSIPATED AND LOAD CURRENT LIMIT VS TEMPERATURE Please refer to the installation notice for precautions about mounting the device on a heatsink. Power dissipated Pd (W) Ambient temperature ( C) 10K/W = No Heatsink / 1LD K/W = 150x150x3mm aluminium sheet 2.2K/W = WF / WF K/W = WF K/W = WF K/W = WF K/W = WF K/W = WF K/W = WF K/W = WF031100

4 E.M.C. EMISSION E.M.C. IMMUNITY GENERAL MISC. CONNEC- TIONS Page 4/5 UK Connections Power Control Screwdriver advised Philips NR2 Philips NR1 Min and max tightening torque 1.8 N.m 0.8 N.m Insulated crimp terminals (round tabs, eyelet type) M5 GENERAL INFORMATION M3 Display Green LED (indicates relay has switched ON) Housing Mounting Noise level UL94V0 2 screws (M4x12mm) No audible noise See mounting sheet Weight 100g STANDARDS Standards IEC Protection level IP00 Protection against direct touch None CE marking Yes UL, culus and VDE approvals Pending TYPE OF TEST STANDARD LEVEL EFFECT E.S.D. (Electrostatic discharges) EN Pending? Radiated electromagnetic fields EN Pending? Fast transients bursts EN Pending No effect Electric chocks EN Pending? Voltage drop EN Radiated and conducted disturbances NFEN55011 Pending

5 Page 5/5 UK DIMENSIONS AND ACCESSORIES Fig. 10 DIMENSIONS (mm) ±0,5 Ø M TOLERANCES: ± M3 ACCESSORIES PROTECTIVE COVER 1K Please consult our website for other accessory references (Heatsinks, mounting adaptors, thermal grease ) 5 Rue Ampère B.P SORBIERS - FRANCE -relais@.com Fax +33 (0) Service Commercial France Tél. : +33 (0) Sales Dept.For Europe Tel. : +33 (0) Sales Dept. Asia : Tél. +33 (0)