EMC Back to Basics. Matthew Carter EMC Product Support Engineer Agilent Technologies Inc. April 16, 2014
|
|
- Leslie Dalton
- 6 years ago
- Views:
Transcription
1 EMC Back to Basics Matthew Carter EMC Product Support Engineer Agilent Technologies Inc. April 16, 2014 Agilent Technologies, Inc. 2014
2 Agenda EMC Back to Basics Overview What is Electromagnetic Compatibility? Which equipment? Pre-compliance vs. Compliance Which standards? EMI Receiver Architecture Specifications: Which are important and why? Making an Emissions Measurement Other equipment considerations Q&A 4
3 Sources of Electromagnetic Interference Natural Sources -Lightning -Sun Spots Unintentional emitting products -Power lines -Motors (mixers, hair dryers etc) -Lighting, appliances Devices that intentionally emit signals -Most computers -Hand held communication devices -Radar, transceivers, broadcast equipment etc 5
4 Basic Definitions Electromagnetic Compatibility (EMC): The ability for electrical devices to operating in the same environment without interfering with one another Electromagnetic Interference (EMI): Electromagnetic energy emissions from one device causing reduced or degraded performance in another device Electromagnetic Compliance A product is considered to be in Electromagnetic Compliance when it meets all applicable electromagnetic regulations. 6
5 EMC Market Overview Global market, mandatory regulation Vendors test in order to be able to sell their products Electronic Smog testing Commercial Standards determined by International Committee Slow moving, political Adaptive Adapt techniques and measurements to meet the needs of rapidly changing products Eg: IT, Cellular, Wireless, Multimedia 7
6 EMC Market Segmentation Measurement Type: Emissions Radiated & Conducted - Compliance - Pre-Compliance Immunity Radiated & Conducted Compliance Application: Commercial Military Sub-segments: - Product Type - Product Class - Country -. 8
7 Definitions: Emissions, Susceptibility, Immunity Radiated Emissions Radiated Susceptibility (or Immunity) Conducted Emissions Conducted Susceptibility (or Immunity)
8 transducer Measurement Equipment Emissions Radiated Emissions Conducted Emissions EUT EUT Mains Compliance receivers Spectrum Analyzers Preamps Antennas Measurement SW Towers Turntables Control SW Equipment Artificial Mains Networks LISN - (line impedance stabilization network) Conducted Transducers Measurement SW Open Sites Anechoic Chambers Semi-Anechoic Chambers TEM cells Reverberation chambers
9 Compliance vs. Precompliance Measurements Full Compliance - Pass/Fail final regulatory testing - Requires specific equipment and test site - must comply to specific Mil or Comm l standards MXE - Expensive and time consuming Precompliance Measurements - Unofficial performance estimate done prior to Full Compliance test - Typically done with SA on available location - Purpose is to minimize chance of failure at Compliance test. X-Series w/ N6141A
10 transducer ESD source Measurement Equipment Immunity Radiated Immunity Conducted Immunity ~ ~ EUT EUT AMN transducer RF Sources Power meters Power amps Antennas Measurement SW Control SW Equipment LISN Coupling Transducers - clamps, etc. ESD sources Screen rooms TEM cells GTEM cells
11 Segmentation Measurement Type: Emissions Radiated & Conducted - Compliance - Pre-Compliance Immunity Radiated & Conducted Compliance Application: Commercial Military Sub-segments: - Product Type - Product Class - Country -.
12 CISPR Recommends Commercial Limits, Measuring Equipment and Methodologies CISPR (Special International Committee on Radio Interference) a sub committee of the IEC (International Electrotechnical Commission) determines and recommends required emissions and immunity: - limits for products sold in the worldwide commercial market - test equipment requirements - test procedures/methodologies
13 CISPR Product Groups CISPR 11 - Industrial, Scientific, and Medical (ISM) Radio-Frequency Equipment CISPR 12 - Vehicles, Motorboats, and Spark-Ignited Engine-Driven Devices CISPR 13 - Sound and Television Broadcast Receivers and Associated Equipment CISPR 14 - Household Appliances, Electric Tools, and Similar Apparatus CISPR 15 - Electrical Lighting and Similar Equipment. CISPR 17 - Suppression Characteristics of Passive Radio Interference Filters and Suppression Components. CISPR 18 - Overhead Power Lines and High-Voltage Equipment CISPR 20 - Sound and Television Broadcast Receivers and Associated Equipment CISPR 21 - Interference to Mobile Radio communications CISPR 22 - Information Technology Equipment Radio Disturbance Characteristics CISPR 24 - Information Technology Equipment Immunity Characteristics CISPR 25 - Receivers Used on Board Vehicles, Boats, and on CISPR 32 Multimedia devices emission testing (under development) CISPR 35 Multimedia devices immunity testing (under development)
14 Commercial requirements for EMI receivers What is CISPR ? Specifies the characteristics and performance of equipment for the measurement of radio disturbance in the frequency range 9 khz to 18 GHz for commercial devices. CISPR 16 Equipment Requirements Detectors (Peak, Quasi-peak, EMI-avg, etc) Reference BW (aka. RBW filter) Amplitude Accuracy Input Impedance Ability to pass the CISPR pulse test And more
15 Commercial Regulations IEC/CISPR Measurement Std. CISPR 16 Equipment Std. CISPR 16 Product Std. - CISPR 11-15, etc. IEC 61XXX GB VCCI ANSI FCC CENELEC EN
16 Commercial EMC Standards - Examples Country /Organization Entity Standards US FCC, DoD FCC Part xx, MIL-STD. xxx IEC CISPR CISPR Pub. xx IEC TC77 IEC 6xxxx EC CENELEC EN 550xx Canada CSA ICES xxx Australia/NZ AS/NZS AS/NZS CISPR xx Japan VCCI J550xx China (Mainland) Korea Taiwan CCC, MoD MIC BSMI GB xxxx- xxxx GJB xxx- xx (equivalent to Mil-STD) Equivalent to EN 550xx CNS xxxx
17 Segmentation Measurement Type: Emissions Radiated & Conducted - Compliance - Pre-Compliance Immunity Radiated & Conducted Compliance Application: Commercial Military Sub-segments: - Product Type - Product Class - Country -.
18 Country-Specific Military Regulations Tend to be based on US MIL STD Current version: 461F (2007) but many include unique emissions and immunity tests
19 MIL-STD 461 Receiver Requirements U.S. military standard Published by the Department of Defense MIL-STD-461 Section Receiver Requirements Peak detector Sensitivity Amplitude accuracy Frequency accuracy Specified dwell times
20 Agenda EMC Back to Basics Overview EMI Receiver Architecture Specifications: Which are important and why? Making an Emissions Measurement Other equipment considerations Q&A 22
21 EMI Receiver Block Diagram Input 2 Pre-amp MXE Input 1 Transient Limiter Attenuation RF Preselector Digital IF Filter Digital Detectors FFT Analog IF Filter Swept vs. FFT Digital Log Amp ADC 23
22 RF Preselector Bands 24
23 RF Pre-selection (RF input filtering) Purpose of RF pre-selection Help to prevent overload by reducing total energy at input mixer RF preselector tracks the center frequency of the EMI receiver The bandwidth of the RF preselector is wider than the widest RBW used Useful in measuring broadband signals Types of filters used in RF pre-selectors Low-pass, Band-pass and High-pass Fixed and Tracking Narrow band signals Broadband signals RF Preselector 25
24 EMI Receiver Block Diagram Input 2 Pre-amp MXE Input 1 Transient Limiter Attenuation RF Preselector Digital IF Filter Digital Detectors FFT Analog IF Filter Swept vs. FFT Digital Log Amp ADC 26
25 Methods to EMI Scanning Stepped Scan Slowest method LO moves for every bin Must re-tune LO each time Swept Scan Slow (slightly faster than Stepped) LO re-tunes once each sweep FFT Time Domain Scan (TDS) Very fast Highly overlapped FFT (>90%) Alternate scan method allowed by CISPR 16 27
26 amplitude amplitude How Time Domain Sweep Saves Time Have to dwell at each RBW Receiver Resolution BW Only have to dwell for each FFT BW (multiple RBWs) Receiver FFT BW frequency Swept or Stepped Frequency Scan Time Domain Frequency Scan frequency 28
27 Agenda EMC Back to Basics Overview EMI Receiver Architecture Specifications: Which are important and why? Making an Emissions Measurement Other equipment considerations Q&A 29
28 Specifications? A Definition Specifications describe the performance of parameters covered by the product warranty (temperature = 5 to 55 C, unless otherwise noted). Typical values describe additional product performance information that is not covered by the product warranty. It is performance beyond specification that 80 % of the units exhibit with a 95 % confidence level over the temperature range 20 to 30 C. Typical performance does not include measurement uncertainty. Nominal values indicate expected performance, or describe product performance that is useful in the application of the product, but is not covered by the product warranty. 30
29 Key Specifications for EMI Sensitivity Amplitude Accuracy Scan Speed Others? 31
30 Specifications: Sensitivity/DANL Sensitivity is the Smallest Signal That Can Be Measured Signal Equals Noise 2.2 db 36
31 Specifications: Sensitivity/DANL Effective Level of Displayed Noise is a Function of RF Input Attenuation signal level 10 db Attenuation = 10 db Attenuation = 20 db Signal To Noise Ratio Decreases as RF Input Attenuation is Increased 37
32 Sensitivity/DANL: IF Filter (RBW) Displayed Noise is a Function of IF Filter Bandwidth 100 khz RBW 10 db 10 db 10 khz RBW 1 khz RBW Decreased BW = Decreased Noise 38
33 Sensitivity/DANL: Summary For Best Sensitivity Use: Narrowest Resolution BW allowed Minimum RF Input Attenuation Sufficient Averaging (video or trace - if allowed) Using the Preamp also improves sensitivity Noise Floor Extension 41
34 Specifications: Amplitude Accuracy Components which contribute to uncertainty are: Input mismatch (VSWR) RF Input attenuator (Atten. switching uncertainty) Mixer and input filter (frequency response) IF gain/attenuation (reference level accuracy) RBW filters (RBW switching uncertainty) Log amp (display scale fidelity) Calibrator (amplitude accuracy) FFT 25
35 Digital IF Improves Amplitude Accuracy Input Connector RF Input Attenuator 2 db Steps Pre-selector Downconversion ADC DSP Input connector (mismatch) Calibrator RF input attenuator flatness and switching Mixer and input filter frequency response Frequency Dependent Frequency Independent Digital IF improves Amplitude Accuracy: Ref Level switching uncertainty (IF gain) Level correction digitally synthesized RBW filter switching uncertainty RBWs all digitally synthesized Display scale fidelity (Log Amp) Log response & display scaling digitally synthesized IF Filter IF Gain Log Amp Video Filter Log ADC 37
36 Digital IF Improves Amplitude Accuracy Input Connector RF Input Attenuator 2 db Steps Pre-selector Downconversion ADC DSP Amplitude Uncertainty Ref Level Switching RBW Switching Display Scale Fidelity N9038A Receiver 0dB Frequency Dependent Analog IF (older receivers) <= +/- 1dB +/-.05dB <= +/-.5dB +/-.15dB <= +/-.85dB Frequency Independent Digital IF improves Amplitude Accuracy: Ref Level switching uncertainty (IF gain) Level correction digitally synthesized RBW filter switching uncertainty RBWs all digitally synthesized Display scale fidelity (Log Amp) Log response & display scaling digitally synthesized IF Filter IF Gain Log Amp Video Filter Log ADC 38
37 Specifications: Scan Speed Need for SPEED DUTs that require short measurement time (ex. motor starter) Test MORE devices Shorter turn-around-time Depends On: Scan type (Stepped, Swept, Time Domain) Resolution Bandwidth Dwell Time RF Preselector Other? 39
38 Agenda EMC Back to Basics Overview EMI Receiver Architecture Specifications: Which are important and why? Making an Emissions Measurement Other equipment considerations Q&A 40
39 Making an emissions measurement Recommended by CISPR Measurement methodology found in CISPR Fastest way to make the measurement MIL Measurements* Pre-scan Data Reduction Maximization Final Measurement Report Generation 41
40 Pre-Scan Preview spectrum using Peak detector Measurement Parameters Prescan Frequency range Limit lines Margins Antenna Factors Scan Type Scan Types Stepped Swept Time Domain Pre-scan Data Reduction Maximization Final Measurement Report Generation 42
41 Data Reduction Signals exceeding the limit are automatically: Marked in red Peaks are marked with white X Added to signal list Only do final measurement on signals exceeding the limit and margin Don t measure unnecessary signals Saves time Signal List Pre-scan Data Reduction Maximization Final Measurement Report Generation 43
42 Maximization Techniques Maximize signal amplitude before final measurement Receiver mode Spectrum Analyzer Mode Monitor Spectrum Simultaneous spectrum and meter measurements Access to signal (suspect) list Meter max hold Spectrum Analyzer mode Switch between EMI receiver and SA modes using global center frequency Powerful analyzer mode Pre-scan Data Reduction Maximization Final Measurement Report Generation 44
43 Final Measurement Signals in list are automatically measured Measure suspect signals with Quasi-peak, EMI average detector, etc. Suspect signals still failing? Start troubleshooting? Pre-scan Data Reduction Maximization Final Measurement Report Generation 45
44 Report Generation Report Generator Settings Screenshots Tables Report Format: PDF or HTML Pre-scan Data Reduction Maximization Final Measurement Report Generation 46
45 Agenda EMC Back to Basics Overview EMI Receiver Architecture Specifications: Which are important and why? Making an Emissions Measurement Other equipment considerations Q&A 47
46 Transducers for EMI measurements a device that receives a signal in the form of one type of energy and converts it to a signal in another form Near Field Probe Near Field Scanner Line Impedance Stabilization Network (LISN) Antennas Other devices? -dictionary.com 48
47 Near Field Probes E & H Field Use Cases Pre-compliance Diagnostics Characteristics E Field Probe Frequency Range Spatial Resolution Sensitivity Measure or Generate Fields Emissions or Susceptibility H Field Probe 49
48 Near Field Scanners 50
49 LISN: Line Impedance Stabilization Network Typically used for conducted emission measurements Isolates the power mains from the EUT Isolates EUT from the power mains Powers the EUT and couples signals to EMI receiver No Transient Limiter Required Power Mains MXE Receiver EUT LISN Types of LISNs V-LISN Delta LISN T-LISN 51
50 EMI Broadband Antenna Examples Double ridged horn Biconical Log Periodic Hybrid Log Periodic Hybrid Log Periodic 52
51 Antenna Factor (db/m) Understanding Antenna Factors Ratio of the electric field to the voltage out of the antenna Linear Units AF = E in V out 20 Typical biconical antenna factors AF = Antenna Factor (1/m) E = Electric Field units (V/m) V = Voltage output from antenna (V) 10 Log Units AF(dB/m) = E(dBµV/m) V(dBµV) Frequency (MHz) 53
52 Antenna Factors on a Typical Display Corrected for a broadband antenna 54
53 Examples of Test Facilities 5 Meter Semi Anechoic* Chamber (Located on the Agilent Santa Rosa site) This chamber uses 2 antenna towers, one for vertical and one for horizontal polarization. Origin Anechoic an- not + echoic (echo) *Anechoic material is made of carbon impregnated rubberized cones or ferrite tiles or both 55
54 Examples of Test Facilities Open Area Test Site (OATS) Useful in low ambient signal environments Reverberation Chamber Uses a mode stirring tuner to generate a uniform field (no absorption material on the walls) GHz Transverse Electro Magnetic Cell (GTEM Cell) Used for smaller devices. Can be used for immunity and emissions. 56
55 Automation Software Reasons for Automation -Supplement skill and knowledge of the tester -Measurements repeatability -Results are presented in a common format -Reduce test time by automating setups -Run turntables and antenna towers Types of Automation -Internally executed application such as N6141A EMI Application -PC based applications Software Available 57
56 Automation Software Receiver Control Room Automation software typically communicates with the receiver over LAN or GPIB Chamber Uses SCPI commands 58
57 Questions? Please type them in the chat box now N9038A MXE EMI Receiver X-Series Signal/Spectrum Analyzers 59
Utilizzo del Time Domain per misure EMI
Utilizzo del Time Domain per misure EMI Roberto Sacchi Measurement Expert Manager - Europe 7 Giugno 2017 Compliance EMI receiver requirements (CISPR 16-1-1 ) range 9 khz - 18 GHz: A normal +/- 2 db absolute
More informationEMC Training. Ing Angelo Cereser Mobile:
EMC Training Ing Angelo Cereser angelo.cereser@microlease.com Mobile: 335 57 88 293 Dott Mirko Bombelli mirko.bombelli@microlease.com Mobile: 335 12 36 792 Agenda Introduzione alle misure EMI Terminologia;
More informationEssential Capabilities of EMI Receivers. Application Note
Essential Capabilities of EMI Receivers Application Note Contents Introduction... 3 CISPR 16-1-1 Compliance... 3 MIL-STD-461 Compliance... 4 Important features not required by CISPR 16-1-1 or MIL-STD-461...
More informationEMC Measurements. Jan Sjögren Electronic Measurements Group Agilent Technologies Page 1. EMC seminar
EMC Measurements Jan Sjögren Electronic Measurements Group Agilent Technologies jan_sjogren@agilent.com Page 1 Day Agenda 8.45 REGISTRATION 9.00 Introduction 9.15 EMC Back to Basics EMC - What is it and
More informationKeysight Technologies Essential Capabilities of EMI Receivers. Application Note
Keysight Technologies Essential Capabilities of EMI Receivers Application Note Contents Introduction... 3 CISPR 16-1-1 Compliance... 3 MIL-STD-461 Compliance... 4 Important features not required by CISPR
More informationTest and Measurement for EMC
Test and Measurement for EMC Bogdan Adamczyk, Ph.D., in.c.e. Professor of Engineering Director of the Electromagnetic Compatibility Center Grand Valley State University, Michigan, USA Ottawa, Canada July
More informationMisure di pre-compliance EMI
Misure di pre-compliance EMI Roberto Sacchi Application Engineer Roberto_sacchi@agilent.com Page 1 Agenda Introduzione alle misure EMI Terminologia; Sistema di misura (antenna, LISN, ricevitore, etc.);
More informationSpecification for Conducted Emission Test
1 of 10 1. EMI Receiver Frequency range 9kHz 7.0 GHz Measurement time per frequency 10 µs to 100 s time sweep, span = 0 Hz - 1 µs to 16000 s Sweep time in steps of 5 % frequency sweep, span 10 Hz - 2.5
More informationKeysight Technologies N6141A & W6141A EMI X-Series Measurement Application. Technical Overview
Keysight Technologies N6141A & W6141A EMI X-Series Measurement Application Technical Overview EMI Measurement Application To avoid costly delays that can result from failed compliance testing, Keysight's
More informationAdvanced Compliance Solutions, Inc FAU Blvd, Suite 310 Boca Raton, Florida (561)
2129.01 Advanced Compliance Solutions, Inc. 3998 FAU Blvd, Suite 310 Boca Raton, Florida 33431 (561) 961-5585 Technical Report No. 09-2067a-2 EMI Evaluation of the AMM Marketing, LLC s E-Pulse UH 900,
More informationEMC Precompliance Systems and Accessories Catalog
EMC Precompliance Systems and Accessories Catalog Agilent 84115EM EMC precompliance systems Agilent E7402A and E7405A EMC precompliance analyzers Agilent E7415A EMC measurement software Agilent EMC precompliance
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) Agilent E7400 A-series EMC Analyzers, Precompliance Systems, and EMI Measurement Software E7401A, E7402A E7403A, E7404A
More informationAlternative Radiated Emission Test Methods Progress Achieved in IND60 Project
Alternative Radiated Emission Test Methods Progress Achieved in IND60 Project Project EMRP IND60: Improved EMC test methods in industrial environments Mohammed Salhi 05-09 September 2016 Wroclaw, Poland
More informationER55 EMI TEST RECEIVER Family of automatic test receivers for measurement of electromagnetic interference from 9kHz to 2.8GHz.
ER55 EMI TEST RECEIVER Family of automatic test receivers for measurement of electromagnetic interference from 9kHz to 2.8GHz. Compact designed and manufactured in compliance with CISPR 16-1-1 For Measurements
More informationOverview of EMC Regulations and Testing. Prof. Tzong-Lin Wu Department of Electrical Engineering National Taiwan University
Overview of EMC Regulations and Testing Prof. Tzong-Lin Wu Department of Electrical Engineering National Taiwan University What is EMC Electro-Magnetic Compatibility ( 電磁相容 ) EMC EMI (Interference) Conducted
More informationEMC Accessories Catalog
EMC Accessories Catalog Transducers and Accessories Agilent 11966 Series Antennas Agilent 11967 Series Conducted EMC Accessories Agilent 11968 Series EMC Positioning Accessories A fully equipped electromagnetic
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) R3000 EMI TEST RECEIVERS Fully IF digital EMI Receivers family for measurement of electromagnetic interference from
More informationER55 EMI TEST RECEIVER Family of automatic test receivers for measurement of electromagnetic interference from 9kHz to 1GHz
ER55 EMI TEST RECEIVER Family of automatic test receivers for measurement of electromagnetic interference from 9kHz to 1GHz Compact designed and manufactured in compliance with CISPR 16-1, For Measurements
More information3250 Series Spectrum Analyzer
The most important thing we build is trust ADVANCED ELECTRONIC SOLUTIONS AVIATION SERVICES COMMUNICATIONS AND CONNECTIVITY MISSION SYSTEMS 3250 Series Spectrum Analyzer > Agenda Introduction
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) EMI Testing According to CSPR Publication 16 Recommendations Combining the 85685A RF preselector with the 8566B or 8568B
More information7. Transmitter Radiated Spurious Emissions and Conducted Spurious Emission
7. Transmitter Radiated Spurious Emissions and Conducted Spurious Emission 7.1 Test Setup Refer to the APPENDIX I. 7.2 Limit According to 15.247(d), in any 100 khz bandwidth outside the frequency band
More informationPMM 7010 EMI RECEIVERS. The EMI Receiver with built-in LISN
The EMI Receiver with built-in LISN 1 Model Frequency Range 7010/00 150 khz to 1 GHz 7010/01 9 khz to 1 GHz 7010/02 9 khz to 30 MHz 7010/03 9 khz to 3 GHz 2 family Built-in 16 A single phase LISN Artificial
More informationAgilent N9320B RF Spectrum Analyzer
Agilent N9320B RF Spectrum Analyzer 9 khz to 3.0 GHz Data Sheet Definitions and Conditions The spectrum analyzer will meet its specifications when: It is within its calibration cycle It has been turned
More informationElectromagnetic Compatibility ( EMC )
Electromagnetic Compatibility ( EMC ) Introduction EMC Testing 1-2 -1 Agenda System Radiated Interference Test System Conducted Interference Test 1-2 -2 System Radiated Interference Test Open-Area Test
More informationEMC/EMI MEASURING INSTRUMENTS & ACCESSORIES SHORT-FORM CATALOG 2011
EMC/EMI MEASURING INSTRUMENTS & ACCESSORIES SHORT-FORM CATALOG 2011 All-in-one Digital EMI Analyzer 10 Hz - 3 GHz PMM 9010/30P EMI Analyzer 10 Hz - 3 GHz Our trek started in a small laboratory over 25
More informationThe Value of Pre-Selection in EMC Testing. Scott Niemiec Application Engineer
The Value of Pre-Selection in EMC Testing Scott Niemiec Application Engineer Video Demonstrating Benefit of Pre-selection 400MHz -1GHz Sweep with RBW = 120kHz Yellow: w/ preselection Green: w/o pre-selection
More informationGlobal EMC Inc. Labs EMC & RF Test Report TVTXP916A04
Global EMC Inc. Labs EMC & RF Test Report As per RSS 210 Issue 8:2010 & FCC Part 15 Subpart C:2013 Unlicensed Intentional Radiators on the Min Xie Project Engineer 11 Gordon Collins Dr, Gormley, ON, L0H
More informationElectromagnetic Compatibility
Electromagnetic Compatibility Introduction to EMC International Standards Measurement Setups Emissions Applications for Switch-Mode Power Supplies Filters 1 What is EMC? A system is electromagnetic compatible
More informationEMC/EMI MEASURING INSTRUMENTS & ACCESSORIES SHORT-FORM CATALOG 2009
EMC/EMI MEASURING INSTRUMENTS & ACCESSORIES SHORT-FORM CATALOG 2009 Our trek started in a small laboratory over 25 years ago. Since then, we ve been focused on making EMC measurements easier and the measuring
More informationKeysight Technologies N9320B RF Spectrum Analyzer
Keysight Technologies N9320B RF Spectrum Analyzer 9 khz to 3.0 GHz Data Sheet Definitions and Conditions The spectrum analyzer will meet its specifications when: It is within its calibration cycle It has
More informationNormalized Site Attenuation Test Report
NVLAP LAB CODE 200974-0 Normalized Site Attenuation Test Report Test Specification NORMALIZED SITE ATTENUATION (NSA) Range 30 MHz 1GHz using the methods of ANSI C63.4-2009; EN 50147-2 (1997); CISPR 16-1-4
More informationAve output power ANT 1(dBm) Ave output power ANT 2 (dbm)
Page 41 of 103 9.6. Test Result The test was performed with 802.11b Channel Frequency (MHz) power ANT 1(dBm) power ANT 2 (dbm) power ANT 1(mW) power ANT 2 (mw) Limits dbm / W Low 2412 7.20 7.37 5.248 5.458
More informationCompliance Engineering Ireland Ltd
Page 1 of 27 Compliance Engineering Ireland Ltd RAYSTOWN, RATOATH ROAD, ASHBOURNE, CO. MEATH, IRELAND Tel: +353 1 8256722 Fax: +353 1 8256733 Project Number: 10E2475-5 Prepared for: Biancamed Ltd By Compliance
More informationVersion TEST REPORT NO. DATE DESCRIPTION
Version NO. DATE DESCRIPTION HCTR1302FR13 February 14, 2013 - First Approval Report - Additional Model Name Page 2 of 25 Table of Contents 1. GENERAL INFORMATION... 4 2. EUT DESCRIPTION... 4 3. TEST METHODOLOGY...
More informationRadiated Spurious Emission Testing. Jari Vikstedt
Radiated Spurious Emission Testing Jari Vikstedt jari.vikstedt@ets-lindgren.com What is RSE? RSE = radiated spurious emission Radiated chamber Emission EMI Spurious intentional radiator 2 Spurious Spurious,
More informationConducted emission pre compliance measurements
V1.1 Conducted emission pre compliance measurements All electronic products need to be tested for electromagnetic emissions that may negatively effect the correct operation of other equipment nearby. Electromagnetic
More informationAn Introduction to FFT EMI Receivers
An Introduction to FFT EMI Receivers Introduction An evolution in EMI receiver design is underway to take advantage of today s digital signal processing (DSP) technologies, using fast Fourier transform
More informationKeysight Technologies Enhance EMC Testing with Digital IF. Application Note
Keysight Technologies Enhance EMC Testing with Digital IF Application Note Introduction With today s accelerating business environment and development cycles, EMC measurement facilities that offer rapid
More informationE M C T E S T Y O U R SOURCE FOR TOP Q U A L I T Y TEST EQUIPMENT & E M C. w w w. h v t e c h n o l o g i e s. c o m
E M C T E S T S O L U T I O N S P A R T N E R S F O R H V & E M C S O L U T I O N S Y O U R SOURCE FOR TOP Q U A L I T Y TEST EQUIPMENT w w w. h v t e c h n o l o g i e s. c o m Transient Immunity Generators
More informationEMC Accessories Catalog
EMC Accessories Catalog A fully equipped electromagnetic compatibility (EMC) laboratory requires a wide variety of instruments, equipment, and accessories to allow measurements to be made accurately and
More informationLaird Attn: Bill Steinike W66 N220 Commerce Ct. Cedarburg, WI Report Constructed by: Zach Wilson, EMC Technician Signature: Date: June 21, 2017
A Test Report # 317241 Equipment Under Test: RM024 Test Date(s): June 9 and June 21, 2017 Prepared for: Laird Attn: Bill Steinike W66 N220 Commerce Ct. Cedarburg, WI 53012 Report Issued by: Adam Alger,
More informationRF Fundamentals Part 2 Spectral Analysis
Spectral Analysis Dec 8, 2016 Kevin Nguyen Keysight Technologies Agenda Overview Theory of Operation Traditional Spectrum Analyzers Modern Signal Analyzers Specifications Features Wrap-up Page 2 Overview
More informationThe Causes and Impact of EMI in Power Systems; Part 1. Chris Swartz
The Causes and Impact of EMI in Power Systems; Part Chris Swartz Agenda Welcome and thank you for attending. Today I hope I can provide a overall better understanding of the origin of conducted EMI in
More informationInterference Analysis and Spectrum Monitor Seminar
Interference Analysis and Spectrum Monitor Seminar Handheld RF & Microwave Instruments Andrew Benn Business Development Manager Agilent Technologies Wednesday 12 th October 2011 1 Agilent Technologies,
More informationEMC / FIELD STRENGTH Test receivers. Fast and straightforward: diagnostic and precompliance measurements with the R&S ESRP
EMC / FIELD STRENGTH Test receivers Fast and straightforward: diagnostic and precompliance measurements with the R&S ESRP 54 Many of the requirements such as speed, functionality and ease of use imposed
More informationFFT 3010 EMI TEST RECEIVER
FFT 3010 EMI TEST RECEIVER Fully FFT digital EMI Receiver for measurement of conducted electromagnetic interference from 9kHz to 30MHz Compact designed and manufactured compliant to CISPR 16 International
More informationAn Introduction to EMC Testing (what can be done with scopes) Vincent Lascoste EMC Product Manager - RSF
An Introduction to EMC Testing (what can be done with scopes) Vincent Lascoste EMC Product Manager - RSF Definition of ElectroMagnetic Compatibility (EMC) EMC is defined as: "The ability of devices and
More informationConducted emission pre compliance measurements
Conducted emission pre compliance measurements All electronic products need to be tested for electromagnetic emissions that may negatively effect the correct operation of other equipment nearby. Electromagnetic
More informationAutomotive EMI/EMC Pre-compliance Tests
Automotive EMI/EMC Pre-compliance Tests Introduction Electromagnetic interference (EMI) regulations are in place throughout the world to provide improved reliability and safety for users of electrical
More informationC-Tick EMC TEST REPORT. For. AC/DC Switching Power Supply
C-Tick EMC TEST REPORT For AC/DC Switching Power Supply Model: CP0515(5V/1.5A); CP0520(5V/2A); CP0530 (5V/3A); CP0540 (5V/4A); CP0550 (5V/5A); CP0560 (5V/6A);CP0615(6V/1.5A); CP0620(6V/2A); CP0625 (6V/2.5A);
More informationFCC REPORT. 570 E1 Camino Real #200, Redwood City, CA 94063, United Manufacturer:
FCC REPORT Applicant: Address of Applicant: Manufacturer: Striiv Inc. 570 E1 Camino Real #200, Redwood City, CA 94063, United States Striiv Inc. Address of 570 E1 Camino Real #200, Redwood City, CA 94063,
More informationKeysight Solutions for EMI Measurements in the Automotive Lab
Measurements in the Automotive Lab Updated Febuary 6, 2018 Jon Kinney RF/uW Applications Engineer Keysight & Partners to Offer a Broad Range of Compliance Test Solutions Keysight Solution Partners Compliance
More informationA Study of Conducted-Emission Stable Source Applied to the EMC US and EU Standards
Fourth LACCEI International Latin American and Caribbean Conference for Engineering and Technology (LACCEI 2006) Breaking Frontiers and Barriers in Engineering: Education, Research and Practice, 21-23
More informationEMC ANECHOIC CHAMBERS 5-METER CHAMBERS
ETS-Lindgren's FACT 5 Chambers offer semi-anechoic radiated emissions (RE) and fully anechoic radiated immunity (RI) compliance test capability for most international EMC compliance regulations. FACT 5
More informationElectromagnetic Compatibility Test Report FCC test results of an automatic dog brush, model EUT: Type 1 AC/DC adaptor: SYS W2E
Electromagnetic Compatibility Test Report FCC test results of an automatic dog brush, model EUT: Type 1 AC/DC adaptor: SYS1308-1809-W2E Customer Customer's representative In the capacity of Reference number
More informationCHAPTER 6 EMI EMC MEASUREMENTS AND STANDARDS FOR TRACKED VEHICLES (MIL APPLICATION)
147 CHAPTER 6 EMI EMC MEASUREMENTS AND STANDARDS FOR TRACKED VEHICLES (MIL APPLICATION) 6.1 INTRODUCTION The electrical and electronic devices, circuits and systems are capable of emitting the electromagnetic
More informationEMC TEST REPORT For MPP SOLAR INC Inverter/ Charger Model Number : PIP 4048HS
EMC-E20130903E EMC TEST REPORT For MPP SOLAR INC Inverter/ Charger Model Number : PIP 4048HS Prepared for : MPP SOLAR INC Address : 4F, NO. 50-1, SECTION 1, HSIN-SHENG S. RD. TAIPEI, TAIWAN Prepared by
More informationChambers Accessories Equipment 1 Equipment 2 Amplifiers Antennas Emission
Chambers Accessories Equipment 1 Equipment 2 Amplifiers Antennas Emission Core-6 EMI Receiver 9 khz 6 GHz Features: Frequency ranges: 9 khz 30 MHz and 30 MHz 6 GHz Fully compliant acc. to CISPR 16-1-1
More informationELECTRONICS TESTING CENTER, TAIWAN
Report No.: 14-06-MAS-233-01 EMC TESTING DEPARTMENT Page: 1/27 CONFORMANCE TEST REPORT FOR ECE R10(REV.05) Report No.: 14-06-MAS-233 Client: Product: Model No.: Comment Issues: Trade Name: Manufacturer/supplier:
More informationTEST REPORT... 1 CONTENT...
CONTENT TEST REPORT... 1 CONTENT... 2 1 TEST RESULTS SUMMARY... 3 2 EMC RESULTS CONCLUSION... 4 3 LABORATORY MEASUREMENTS... 6 4 EMI TEST... 7 4.1 CONTINUOUS CONDUCTED DISTURBANCE VOLTAGE TEST... 7 4.2
More informationL.S. Compliance, Inc. W66 N220 Commerce Court Cedarburg, WI
L.S. Compliance, Inc. W66 N220 Commerce Court Cedarburg, WI 53012 262-375-4400 COMPLIANCE TESTING OF: Quartex Synchronization Transmitter Model FM-72 PREPARED FOR: Quartex, Division of Primex, Inc. 965
More informationTEST REPORT: ELECTROMAGNETIC COMPATIBILITY - ESA Regulation Consolidated to Supplement 2 (Revision 4 Amendment 2)
Vehicle Certification Agency, 1 The Eastgate Office Centre Eastgate Road, Bristol, BS5 6XX, United Kingdom. Telephone: +44 (0) 117 951 5151 Fax: +44 (0) 117 952 4103 Email: enquiries@vca.gov.uk www.dft.gov.uk/vca
More informationEMC Test Facility Sale
EMC Test Facility Sale Radiated Emissions Pre-Compliance Conducted Emissions Full-Compliance Radiated & Conducted Immunity Full-Compliance 1 Please find an information pack attached for an EMC test facility.
More informationFCC REPORT. Dongguan Hele Electronics Co.,Ltd. * In the configuration tested, the EUT complied with the standards specified above.
Report No.: GTS201708000040F02 FCC REPORT Applicant: Address of Applicant: Manufacturer: Dongguan Hele Electronics Co.,Ltd. Dalingya Industrial Zone,Daojiao Town,Dongguan City,Guangdong,China Dongguan
More informationFCC 47 CFR PART 15 SUBPART B
FCC 47 CFR PART 15 SUBPART B TEST REPORT For DC TO DC CONVERTER Model : D100 Series Issued for MicroPower Direct, LLC 232 Tosca Drive Stoughton, MA02072 U.S.A. Issued by Compliance Certification Services
More informationFCC REPORT. Dongguan Hele Electronics Co.,Ltd. * In the configuration tested, the EUT complied with the standards specified above.
+ Applicant: Address of Applicant: Manufacturer: FCC REPORT Dongguan Hele Electronics Co.,Ltd. Report No.: GTS201708000040F01 Dalingya Industrial Zone,Daojiao Town,Dongguan City,Guangdong,China Dongguan
More informationEN 55022: 2010+AC:2011 Clause 6.1 Pass. Harmonic Current EN :2006+A1:2009+A2:2009 Class A N/A
Reference No.: WT12106773-N-S-E Page 2 of 33 1 Test Summary Test Item Mains Terminal Disturbance Voltage, 150KHz to 30MHz Radiation Emission, 30MHz to 1000MHz EMISSION Test Standard Class / Severity Result
More informationFCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of. Trade Name : Activision. Model Number: / FCC ID: XLU
FCC PART 15C TEST REPORT FOR CERTIFICATION On Behalf of Activision Publishing, Inc USB Wireless Receiver for Wii & USB Wireless Receiver for PS3 Trade Name : Activision. Model Number: 83973791/84148791
More informationHarmonic Current emission EN :2014 Class A Pass. Voltage Fluctuation and Flicker EN :2013 Clause 5 Pass
Reference No.: WTS15F0323845E Page 2 of 33 1 Test Summary Test Item Mains Terminal Disturbance Voltage, 148.5kHz to 30MHz Disturbance Power, 30MHz to 300MHz Discontinuous Disturbance (Click) Radiated Emission,
More informationConducted and Radiated Emissions Testing APPLICATION NOTE
Conducted and Radiated Emissions Testing Contents Introduction to EMC Testing... 3 Compliance Testing...3 Pre-Compliance Testing...4 Test Setup... 5 Radiated Tests...5 Conducted Tests...6 LISN (Line Impedance
More informationKeysight N9038A MXE EMI Receiver Self-Guided Demonstration
Keysight N9038A MXE EMI Receiver Self-Guided Demonstration Demo Guide This document demonstrates electromagnetic interference (EMI) compliance measurements using the MXE EMI receiver. 02 Keysight N9038A
More informationEMI 相容性測試 預相容性測試及量測法規
EMI 相容性測試 預相容性測試及量測法規 12/13/2016 太克科技 Laurance Yeh 葉志豪 chi-hao.yeh@tektronix.com Agenda EMI introduction EMI pre-compliance and debugging tools RSA306B demo MDO4000C demo lab 13 December 2016 Agenda EMI
More informationDiscontinuous Disturbance (Click) EN :2006+A1:2009+A2:2011 Clause N/A** Radiated Emission, 30MHz to 1000MHz
Reference No.: WTN13F0706038E Page 2 of 40 1 Test Summary Test Item Mains Terminal Disturbance Voltage, 148.5kHz to 30MHz Disturbance Power, 30MHz to 300MHz EMISSION Test Standard Class / Severity Result
More informationEMC Test report for LED Panel Light Models , , , , ,
4326247.50 EMC Test report for LED Panel Light Models 000529, 000530, 000531, 000532, 000535, 000536 Guangzhou, date of issue: 2016-02-24 Author:Jazz Liang By order of Marvo Verlichting B.V. at Hoogeveen,
More informationLow-cost EMI Pre-compliance Testing Using a Spectrum Analyzer APPLICATION NOTE
Low-cost EMI Pre-compliance Testing Using a Spectrum Analyzer APPLICATION NOTE Application Note 2 www.tektronix.com/emi Low-cost EMI Pre-compliance Testing Using a Spectrum Analyzer EMI regulations are
More informationDynamic Sciences International, Inc. Detection with Direction
Dynamic Sciences International, Inc Detection with Direction CORPORATE OVERVIEW WHO WE ARE Dynamic Sciences International, Inc. (DSII) is a public corporation Serving customers worldwide since 1972. DSII
More informationTest Report Version. Test Report No. Date Description. DRTFCC Sep. 12, 2014 Initial issue
DEMC1407-02828 FCC ID: 2AAAQH660W Test Report Version Test Report No. Date Description DRTFCC1409-1165 Sep. 12, 2014 Initial issue Page 2 DEMC1407-02828 FCC ID: 2AAAQH660W Table of Contents 1. EUT DESCRIPTION...
More informationESA-E Series Spectrum Analyzer
ESA-E Series Spectrum Analyzer Data Sheet Available frequency ranges: E4402B 9 khz to 3.0 GHz E4404B 9 khz to 6.7 GHz E4405B 9 khz to 13.2 GHz E4407B 9 khz to 26.5 GHz Table of Contents Definitions of
More informationRevision history. Revision Date of issue Test report No. Description KES-RF-14T0042 Initial
Page (2 ) of (34) Revision history Revision Date of issue Test report No. Description - 2014.08.25 Initial Page (3 ) of (34) TABLE OF CONTENTS 1. General information... 4 1.1. EUT description... 4 1.2.
More informationTEST SUMMARY. Prüfbericht - Nr.: Test Report No.: Seite 2 von 25. Page 2 of 25
15072259 001 Seite 2 von 25 Page 2 of 25 TEST SUMMARY 4.1.1 HARMONICS ON AC MAINS 4.1.2 VOLTAGE FLUCTUATIONS ON AC MAINS 4.1.3 MAINS TERMINAL CONTINUOUS DISTURBANCE VOLTAGE 4.1.4 DISCONTINUOUS INTERFERENCE
More information2310 to 2390 MHz, 3m distance MCS8 (MIMO) to 2500 MHz Restricted band MCS8 (MIMO)
2310 to 2390 MHz, 3m distance MCS8 (MIMO) Lower band edge, Average (Low Channel) Lower band edge, Peak (Low Channel) 2483.5 to 2500 MHz Restricted band MCS8 (MIMO) Upper band edge, Peak (High Channel)
More informationSemi Anechoic Chamber (SAC)
1 of 9 Semi Anechoic Chamber (SAC) Approximate Dimensions of 3m Semi Anechoic Chamber (SAC) Length: 10m Width: 9m Height: 9m Frequency range of Semi Anechoic Chamber: 9 KHz to 40 GHz Emission test (EMI):
More informationINTRODUCTION TO CONDUCTED EMISSION
IEEE EMC Chapter - Hong Kong Section EMC Seminar Series - All about EMC Testing and Measurement Seminar 2 INTRODUCTION TO CONDUCTED EMISSION By Duncan FUNG 18 April 2015 TOPICS TO BE COVERED Background
More informationFCC Part 15 Subpart B
Report No.: 15A111603E-F Page 1 of 23 Test Report FCC Part 15 Subpart B for Electromagnetic Interference of Product: Managed PoE Industrial Ethernet Switch Trade Name: N/A Model Number: IS-DG512P-2F-8;
More informationFCC 47 CFR PART 15 SUBPART B TEST REPORT SHENZHEN EAGLE TECHNOLOGY CO., LTD Mirror photo booth Model No.: EAGMR
FCC 47 CFR PART 15 SUBPART B TEST REPORT SHENZHEN EAGLE TECHNOLOGY CO., LTD Mirror photo booth Model No.: EAGMR Prepared for Address : SHENZHEN EAGLE TECHNOLOGY CO., LTD : A FIoor 1 BIdg.14, Changfeng
More informationTable of Contents 1. GENERAL INFORMATION SYSTEM TEST CONFIGURATION CONDUCTED EMISSIONS TEST RADIATED EMISSION TEST...
Table of Contents 1. GENERAL INFORMATION... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST... 4 1.2 RELATED SUBMITTAL(S) / GRANT (S)... 7 1.3 TEST METHODOLOGY... 7 1.4 EQUIPMENT MODIFICATIONS... 7
More informationEN 55015: 2013 Clause Pass. EN 55015: 2013 Clause Pass. EN 55015: 2013 Clause Pass
Reference No.: WTD15S0730643E Page 2 of 42 1 Test Summary Test Item Conducted Disturbance at Mains Terminal, 9kHz to 30MHz Radiation electromagnetic disturbance, 9kHz to 30MHz Radiation Emission, 30MHz
More informationFCC TEST REPORT. for. 47 CFR, Part 15, Subpart C. SPORTON International Inc.
FCC TEST REPORT for 47 CFR, Part 15, Subpart C Equipment Trade Name Model No. FCC ID Filing Type Applicant : GamePad : Genius : Wireless G-12X : FSUGG0005 : Certification : KYE Systems Corp. No. 492, Sec.
More informationTrees, vegetation, buildings etc.
EMC Measurements Test Site Locations Open Area (Field) Test Site Obstruction Free Trees, vegetation, buildings etc. Chamber or Screened Room Smaller Equipments Attenuate external fields (about 100dB) External
More informationSpectrum Analyzers 2680 Series Features & benefits
Data Sheet Features & benefits n Frequency range: 9 khz to 2.1 or 3.2 GHz n High Sensitivity -161 dbm/hz displayed average noise level (DANL) n Low phase noise of -98 dbc/hz @ 10 khz offset n Low level
More informationWest Michigan IEEE EMC Chapter Meeting
West Michigan IEEE EMC Chapter Meeting Intertek On-site Demonstration- Dale Wine 9.27.12 1 Global Network: Intertek Group Countries Locations Staff 110+ 1000+ 30,000+ Floated May 2002 LSE: ITRK (4.5 GBP)
More informationFCC TEST REPORT. Table of Contents. Report no. ETLE , Page 2 of 21
Table of Contents FCC Measurement Report 1. Introduction 2. Product Information 3. Description of Tests 4. Test Condition 5. Test Results 5.1 Summary of Test Results 5.2 Conducted Emissions Measurement
More informationDSI-600 EMI Test & Measurement Receiver
DSI-600 EMI Test & Measurement Receiver Product Brochure DSI-600 EMI TEST & Measurement Receiver Product Brochure December 2017 Dynamic Sciences International, Inc. DSI 600 Series EMI Test & Measurement
More informationFCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-247 ISSUE 1 BLUETOOTH LOW ENERGY CERTIFICATION TEST REPORT FOR
FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-247 ISSUE 1 BLUETOOTH LOW ENERGY CERTIFICATION TEST REPORT FOR WLAN 2X2 MIMO 802.11a/b/g/n/ac with BLUETOOTH MODEL NUMBER: P2180 REPORT NUMBER: 15U21878-E2V1
More information8 Hints for Better Spectrum Analysis. Application Note
8 Hints for Better Spectrum Analysis Application Note 1286-1 The Spectrum Analyzer The spectrum analyzer, like an oscilloscope, is a basic tool used for observing signals. Where the oscilloscope provides
More informationPage: 1 of 20 EMC TEST REPORT EN55024:1998+A2:2003
Page: 1 of 20 EMC TEST REPORT Reference No. Applicant : WT05060412 : Gembird Electronics Ltd. Equipment Under Test (EUT) : Product Name : Cable Standards Model No : UAS111-M, UAS111, UAS112 : EN55022:1998+A2:2003
More informationFCC REPORT. Dongguan Hele Electronics Co., Ltd. J11, J12, J13, Q7, Q28, Q26, Q29
FCC REPORT Applicant: Dongguan Hele Electronics Co., Ltd. Address of Applicant: Dalingya Industrial Zone, Daojiao Town, Dongguan City, Guangdong China Equipment Under Test (EUT) Product Name: Model No.:
More informationTitle: Test on 5.8 GHz Band Outdoor WiFi (802.11b/g) Wireless Base Station
Page 20 of 51 Pages 7.5. Conducted spurious emission 7.5.1. Requirements: Clause 15.247(d). In any 100 khz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional
More informationAgilent N8973A, N8974A, N8975A NFA Series Noise Figure Analyzers. Data Sheet
Agilent N8973A, N8974A, N8975A NFA Series Noise Figure Analyzers Data Sheet Specifications Specifications are only valid for the stated operating frequency, and apply over 0 C to +55 C unless otherwise
More informationTABLE OF CONTENTS 1. GENERAL INFORMATION... 4
TABLE OF CONTENTS 1. GENERAL INFORMATION... 4 1.1. EUT DESCRIPTION... 4 1.2. TEST STANDARDS AND RESULTS... 5 1.3. FACILITIES AND ACCREDITATIONS... 6 1.3.1. FACILITIES... 6 1.3.2. TEST ENVIRONMENT CONDITIONS...
More information