Active Sensors Unit assembly process for the ATLAS High Granularity Timing Device
|
|
- Julian Clarke
- 6 years ago
- Views:
Transcription
1 Active Sensors Unit assembly process for the ATLAS High Granularity Timing Device D. Lacour for LPNHE Paris group 1. Introduction: Calice Si-W calorimeter concept 2. Gluing and positioning automated device description 3. Gluing tests on different geometries 4. Summary - next steps Didier Lacour LPNHE Santa Cruz, March
2 Calice Si-W calorimeter concept Active sensor unit: Si sensors PCB Electronics Sensors are glued with a 20um precision and reproducible process. Glue is dispended in order to form 200 um thick dots. 2
3 Calice detector layers assembly and tests Assembly done with gluing and positioning robots: automated system developed in the framework of the Calice R&D program Electrical test to control the sensors before gluing, to check the short cuts immediately after gluing to measure the I(V) curves Metrology using a coordinate measuring machine (tri-dim machine): squaring, parallel edges, size, thickness flatness 3
4 Gluing and positioning automated process Cartesian robot (XYZ monitoring) : arm supporting suction cup and camera. Control cabinet of the positioning robot Plate for one wafer Hinged plate for 4 sensors PCB plate Gluing robot Glue dispenser Plate for GelPak box + wafer Syringes for glue deposition 4
5 Assembly steps Position 4 sensors, one by one (cartesian robot): each sensor is taken from the supporting plate and driven to the hinged plate to be placed at the right position. Done four times, very precisely thanks to a map which has been defined before. The position is also checked with the camera. The sensors are maintained with a vacuum pressure system (-1 bar). Deposit glue onto the PCB (dispenser robot): 2 syringes are used to dispense glue. The PCB is also maintained with a vacuum pressure system (-1 bar). The plate with 4 sensors is tuned onto the PCB. The two plates are maintained together during the glue polymerisation. Heating resistances are used for the polymerisation (40 C) 5
6 Gluing tests on different geometries Calice geometry 4 wafers / PCB Sensor parameters Dimension up to 90 x 90 mm Pads 5 x 5 mm Thickness 330 µm 256 X 4 = 1024 glue dots Glue dots After gluing (glass plate) 6
7 Gluing tests on different geometries First test with dummy boards with copper pads using Calice pattern Matrix pitch : 5 mm Pad dimension : 3 x 3 mm, limit for the process Decrease the capacitance value 7
8 Gluing test on 3 X 3 and 2 X 2 prototype geometry 4 geometries : 3 X 3 matrix Copper pads: 1.7*1.7 mm² Inter-pad gap: 0.3 mm 2 X 2 matrix Copper pads: 1.7*1.7 mm² Inter-pad gap: 0.3 mm 2 X 2 matrix Copper pads: 2.7*2.7 mm² Inter-pad gap: 0.3 mm 3 X 3 matrix Copper pads: 2.7*2.7 mm² Inter-pad gap: 0.3 mm To simulate 3*3 pads pin diode 2*2 pads LGAD 8
9 Gluing test on 3 X 3 and 2 X 2 prototype geometry The dummy PCB is extremely flat PCB, and is not equipped ( no components) Glass plate : 9 cm X 9cm 300 µm thick 9
10 Test on 3 X 3 mm prototype geometry: 3 X 3 and 2 X 2 pads Dispenser pressure: 2 3 bar Glue thickness: 200 µm Test on 2 X 2 mm prototype geometry Dispenser pressure: 0.5 bar Need to reduce the amount of glue to prevent short-circuits Minimum glue thickness for mechanical support = 150 um Then, the amount of glue is no longer sufficient to ensure electrical contact 10
11 Summary - next steps Pitch mm Pads surface mm² inter-pad gap mm Dispenser pressure bar Glue thickness µm mechanical strength / electrical contact / no short-circuit X OK X OK X NO For the time being, 3 X 3 mm pads geometry is compatible with the gluing process The method does not allow an electrical contact for 2 X 2 mm pads geometry Next steps: Gluing test with round copper pads smaller than the glue dots (as small as possible) to decrease the PCB capacitance Use thinner glass plates ( µm) to check handling method Study the radiation hardness of the glue at JSI (AIDA2020) Fluence levels: n/cm², n/cm², n/cm² - Samples : electrical et mechanical behavior of the glue after irradiation. Study the thermo-mechanical effects : thermal aging at -20 C of one ASU 11
Si-W electromagnetic calorimeter. Contribution in the development of an assembly line for highly granular calorimeters with semiconductor readout
Si-W electromagnetic calorimeter Contribution in the development of an assembly line for highly granular calorimeters with semiconductor readout Gluing robot system PCB Metrology Electrical tests Quality
More informationThe HGTD: A SOI Power Diode for Timing Detection Applications
The HGTD: A SOI Power Diode for Timing Detection Applications Work done in the framework of RD50 Collaboration (CERN) M. Carulla, D. Flores, S. Hidalgo, D. Quirion, G. Pellegrini IMB-CNM (CSIC), Spain
More informationA High-Granularity Timing Detector for the Phase-II upgrade of the ATLAS Calorimeter system Detector concept description and first beam test results
A High-Granularity Timing Detector for the Phase-II upgrade of the ATLAS Calorimeter system Detector concept description and first beam test results 03/10/2017 ATL-LARG-SLIDE-2017-858 Didier Lacour On
More informationSilicon sensors for the LumiCal for the Very Forward Region
Report No. 1993/PH Silicon sensors for the LumiCal for the Very Forward Region J. Błocki, W. Daniluk, W. Dąbrowski 1, M. Gil, U. Harder 2, M. Idzik 1, E. Kielar, A. Moszczyński, K. Oliwa, B. Pawlik, L.
More informationModule Integration Sensor Requirements
Module Integration Sensor Requirements Phil Allport Module Integration Working Group Sensor Geometry and Bond Pads Module Programme Issues Numbers of Sensors Required Nobu s Sensor Size Summary n.b. 98.99
More informationDevelopment of Pixel Detectors for the Inner Tracker Upgrade of the ATLAS Experiment
Development of Pixel Detectors for the Inner Tracker Upgrade of the ATLAS Experiment Natascha Savić L. Bergbreiter, J. Breuer, A. Macchiolo, R. Nisius, S. Terzo IMPRS, Munich # 29.5.215 Franz Dinkelacker
More informationMAPS-based ECAL Option for ILC
MAPS-based ECAL Option for ILC, Spain Konstantin Stefanov On behalf of J. Crooks, P. Dauncey, A.-M. Magnan, Y. Mikami, R. Turchetta, M. Tyndel, G. Villani, N. Watson, J. Wilson v Introduction v ECAL with
More informationLarge Silicon Tracking Systems for ILC
Large Silicon Tracking Systems for ILC Aurore Savoy Navarro LPNHE, Universite Pierre & Marie Curie/CNRS-IN2P3 Roles Designs Main Issues Current status R&D work within SiLC R&D Collaboration Tracking Session
More informationNew fabrication and packaging technologies for CMOS pixel sensors: closing gap between hybrid and monolithic
New fabrication and packaging technologies for CMOS pixel sensors: closing gap between hybrid and monolithic Outline Short history of MAPS development at IPHC Results from TowerJazz CIS test sensor Ultra-thin
More informationirst: process development, characterization and first irradiation studies
3D D detectors at ITC-irst irst: process development, characterization and first irradiation studies S. Ronchin a, M. Boscardin a, L. Bosisio b, V. Cindro c, G.-F. Dalla Betta d, C. Piemonte a, A. Pozza
More informationPixel sensors with different pitch layouts for ATLAS Phase-II upgrade
Pixel sensors with different pitch layouts for ATLAS Phase-II upgrade Different pitch layouts are considered for the pixel detector being designed for the ATLAS upgraded tracking system which will be operating
More informationStrip Detectors. Principal: Silicon strip detector. Ingrid--MariaGregor,SemiconductorsasParticleDetectors. metallization (Al) p +--strips
Strip Detectors First detector devices using the lithographic capabilities of microelectronics First Silicon detectors -- > strip detectors Can be found in all high energy physics experiments of the last
More informationMicromegas calorimetry R&D
Micromegas calorimetry R&D June 1, 214 The Micromegas R&D pursued at LAPP is primarily intended for Particle Flow calorimetry at future linear colliders. It focuses on hadron calorimetry with large-area
More informationQuality Assurance for the ATLAS Pixel Sensor
Quality Assurance for the ATLAS Pixel Sensor 1st Workshop on Quality Assurance Issues in Silicon Detectors J. M. Klaiber-Lodewigs (Univ. Dortmund) for the ATLAS pixel collaboration Contents: - role of
More informationOkamoto Machine Tool Works, LTD. June 22, th SEMATECH Symposium Japan 1
Okamoto Machine Tool Works, LTD 1 Contents Solutions for TSV Wafer Thinning Process (Front Side Via) TSV Wafer Thinning Challenges Process Improvement (4-years Development) TSV Wafer Thinning Tool (TSV300)
More informationDevelopment of Ultra Fast Silicon Detectors for 4D Tracking
Development of Ultra Fast Silicon Detectors for 4D Tracking V. Sola, R. Arcidiacono, R. Bellan, A. Bellora, S. Durando, N. Cartiglia, F. Cenna, M. Ferrero, V. Monaco, R. Mulargia, M.M. Obertino, R. Sacchi,
More informationAssembly Instructions for SCC1XX0 series
Technical Note 82 Assembly Instructions for SCC1XX0 series TABLE OF CONTENTS Table of Contents...1 1 Objective...2 2 VTI's 32-lead Dual In-line Package (DIL-32)...2 3 DIL-32 Package Outline and Dimensions...2
More informationDesign and Construction of Large Size Micromegas Chambers for the ATLAS Phase-1 upgrade of the Muon Spectrometer
Advancements in Nuclear Instrumenta2on Measurement Methods and their Applica2ons 20-24 April 2015, Lisbon Congress Center Design and Construction of Large Size Micromegas Chambers for the ATLAS Phase-1
More informationQ1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4 Q1-2 Q3-4. Final design and pre-production.
high-granularity sfcal Performance simulation, option selection and R&D Figure 41. Overview of the time-line and milestones for the implementation of the high-granularity sfcal. tooling and cryostat modification,
More informationAssembly Instructions for SCA6x0 and SCA10x0 series
Technical Note 71 Assembly Instructions for SCA6x0 and SCA10x0 series TABLE OF CONTENTS Table of Contents...1 1 Objective...2 2 VTI'S DIL-8 and DIL-12 packages...2 3 Package Outline and Dimensions...2
More informationPrototype Performance and Design of the ATLAS Pixel Sensor
Prototype Performance and Design of the ATLAS Pixel Sensor F. Hügging, for the ATLAS Pixel Collaboration Contents: - Introduction - Sensor Concept - Performance fi before and after irradiation - Conclusion
More informationRecent Technological Developments on LGAD and ilgad Detectors for Tracking and Timing Applications
Recent Technological Developments on LGAD and ilgad Detectors for Tracking and Timing Applications G. Pellegrini 1, M. Baselga 1, M. Carulla 1, V. Fadeyev 2, P. Fernández-Martínez 1, M. Fernández García
More informationActivités R&D Calice. High Granular Timing Detector ATLAS Phase II Upgrade
High Granular Timing Detector ATLAS Phase II Upgrade 1. Enjeux de physique 2. Organisation 3. Échéances 4. Instituts IN2P3 LPNHE 5. Simulation et performance 6. Géométrie 7. Senseurs et connexions 8. Scénario
More informationConstruction and Performance of the stgc and Micromegas chambers for ATLAS NSW Upgrade
Construction and Performance of the stgc and Micromegas chambers for ATLAS NSW Upgrade Givi Sekhniaidze INFN sezione di Napoli On behalf of ATLAS NSW community 14th Topical Seminar on Innovative Particle
More informationSSD Development for the ATLAS Upgrade Tracker
SSD Development for the ATLAS Upgrade Tracker Meeting Mo., Feb. 26, 2007. 2-6 pm; CERN Rm. 13-3-005 ATL-P-MN-0006 v.1 Development of non-inverting Silicon strip detectors for the ATLAS ID Upgrade 1) DC
More informationHV BOARD. Claudio Arnaboldi Gianluigi Pessina INFN, Milano. Thierry Gys, Didier Piedigrossi CERN. LHCb, 15/12/2004 1
HV BOARD Claudio Arnaboldi Gianluigi Pessina INFN, Milano Thierry Gys, Didier Piedigrossi CERN LHCb, 15/12/2004 1 HV distribution Half Column (8 HPDs) Half Column (8 HPDs) 20 KV Input HPD 2 HPD 1 FILTER
More informationProcesses for Flexible Electronic Systems
Processes for Flexible Electronic Systems Michael Feil Fraunhofer Institut feil@izm-m.fraunhofer.de Outline Introduction Single sheet versus reel-to-reel (R2R) Substrate materials R2R printing processes
More informationSimulation of High Resistivity (CMOS) Pixels
Simulation of High Resistivity (CMOS) Pixels Stefan Lauxtermann, Kadri Vural Sensor Creations Inc. AIDA-2020 CMOS Simulation Workshop May 13 th 2016 OUTLINE 1. Definition of High Resistivity Pixel Also
More informationSilicon Sensor Developments for the CMS Tracker Upgrade
Silicon Sensor Developments for the CMS Tracker Upgrade on behalf of the CMS tracker collaboration University of Hamburg, Germany E-mail: Joachim.Erfle@desy.de CMS started a campaign to identify the future
More informationAPPLICATION NOTE 6381 ORGANIC LAND GRID ARRAY (OLGA) AND ITS APPLICATIONS
Keywords: OLGA, SMT, PCB design APPLICATION NOTE 6381 ORGANIC LAND GRID ARRAY (OLGA) AND ITS APPLICATIONS Abstract: This application note discusses Maxim Integrated s OLGA and provides the PCB design and
More informationRadiation hardness and precision timing study of Silicon Detectors for the CMS High Granularity Calorimeter (HGC)
Radiation hardness and precision timing study of Silicon Detectors for the CMS High Granularity Calorimeter (HGC) Esteban Currás1,2, Marcos Fernández2, Christian Gallrapp1, Marcello Mannelli1, Michael
More informationThe LHCb VELO Upgrade. Stefano de Capua on behalf of the LHCb VELO group
The LHCb VELO Upgrade Stefano de Capua on behalf of the LHCb VELO group Overview [J. Instrum. 3 (2008) S08005] LHCb / Current VELO / VELO Upgrade Posters M. Artuso: The Silicon Micro-strip Upstream Tracker
More informationThin Silicon R&D for LC applications
Thin Silicon R&D for LC applications D. Bortoletto Purdue University Status report Hybrid Pixel Detectors for LC Next Linear Collider:Physic requirements Vertexing 10 µ mgev σ r φ,z(ip ) 5µ m 3 / 2 p sin
More informationDispenser printed proximity sensor on fabric for creative smart fabric applications
Dispenser printed proximity sensor on fabric for creative smart fabric applications Yang Wei, Russel Torah, Yi Li and John Tudor University of Southampton, Southampton, United Kingdom, SO17 3BJ Tel: +44(0)23
More informationLeakage Current Prediction for GLAST Silicon Detectors
SCIPP 97/16 Leakage Current Prediction for GLAST Silicon Detectors T. Dubbs, H.F.-W Sadrozinski, S. Kashigan, W. Kroeger, S. Jaggar, R.Johnson, W. Rowe, A. Webster SCIPP, University of California Santa
More informationDevelopment of n-in-p Active Edge Pixel Detectors for ATLAS ITK Upgrade
Development of n-in-p Active Edge Pixel Detectors for ATLAS ITK Upgrade Tasneem Rashid Supervised by: Abdenour Lounis. PHENIICS Fest 2017 30th OUTLINE Introduction: - The Large Hadron Collider (LHC). -
More informationRESERVOIR PRINTING IN DEEP CAVITIES
As originally published in the SMTA Proceedings RESERVOIR PRINTING IN DEEP CAVITIES Phani Vallabhajosyula, Ph.D., William Coleman, Ph.D., Karl Pfluke Photo Stencil Golden, CO, USA phaniv@photostencil.com
More informationCMOS pixel sensors developments in Strasbourg
SuperB XVII Workshop + Kick Off Meeting La Biodola, May 2011 CMOS pixel sensors developments in Strasbourg Outline sensor performances assessment state of the art: MIMOSA-26 and its applications Strasbourg
More informationAIDA-2020 Advanced European Infrastructures for Detectors at Accelerators. Milestone Report
AIDA-2020-MS15 AIDA-2020 Advanced European Infrastructures for Detectors at Accelerators Milestone Report Design specifications of test stations for irradiated silicon sensors and LHC oriented front-end
More information1. PUBLISHABLE SUMMARY
Ref. Ares(2018)3499528-02/07/2018 1. PUBLISHABLE SUMMARY Summary of the context and overall objectives of the project (For the final period, include the conclusions of the action) The AIDA-2020 project
More informationCALICE AHCAL overview
International Workshop on the High Energy Circular Electron-Positron Collider in 2018 CALICE AHCAL overview Yong Liu (IHEP), on behalf of the CALICE collaboration Nov. 13, 2018 CALICE-AHCAL Progress, CEPC
More informationHV BOARD. Claudio Arnaboldi Tito Bellunato Gianluigi Pessina INFN, Milano. Thierry Gys, Didier Piedigrossi CERN. LHCb, 20/01/2005 Genova 1
HV BOARD Claudio Arnaboldi Tito Bellunato Gianluigi Pessina INFN, Milano Thierry Gys, Didier Piedigrossi CERN LHCb, 20/01/2005 Genova 1 HV distribution Half Column (8 HPDs) Half Column (8 HPDs) 20 KV Input
More informationTheremino FlickerMeter
Theremino System Theremino FlickerMeter Building the hardware theremino system - Theremino FlickerMeter Hardware - December 5, 2017 - Page 1 Components For this project we need only three components: 1)
More informationRD51 ANNUAL REPORT WG1 - Technological Aspects and Development of New Detector Structures
RD51 ANNUAL REPORT 2009 WG1 - Technological Aspects and Development of New Detector Structures Conveners: Serge Duarte Pinto (CERN), Paul Colas (CEA Saclay) Common projects Most activities in WG1 are meetings,
More informationSIM-Detecteurs 2014 LPNHE-Paris
SIM-Detecteurs 2014 LPNHE-Paris The application of Silvaco process and device simulation program to the development of silicon detector for the high energy particle detection Li Long llong@cismst.de CiS
More informationThe first uncooled (no thermal) MWIR FPA monolithically integrated with a Si-CMOS ROIC: a 80x80 VPD PbSe FPA
DOI 10.516/irs013/i4.1 The first uncooled (no thermal) MWIR FPA monolithically integrated with a Si-CMOS ROIC: a 80x80 VPD PbSe FPA G. Vergara, R. Linares-Herrero, R. Gutiérrez-Álvarez, C. Fernández-Montojo,
More informationStudies on MCM D interconnections
Studies on MCM D interconnections Speaker: Peter Gerlach Department of Physics Bergische Universität Wuppertal D-42097 Wuppertal, GERMANY Authors: K.H.Becks, T.Flick, P.Gerlach, C.Grah, P.Mättig Department
More informationPassive Direct Print Sensors
Passive Wireless Sensor Technology Workshop June 6-7, 2012 Hyatt Regency, La Jolla, CA Passive Direct Print Sensors Mike Newton mnewton@nscrypt.com nscrypt Inc. Orlando, Florida University of Texas at
More informationSingle Sided and Double Sided Silicon MicroStrip Detector R&D
Single Sided and Double Sided Silicon MicroStrip Detector R&D Tariq Aziz Tata Institute, Mumbai, India SuperBelle, KEK December 10-12, 2008 Indian Effort Mask Design at TIFR, Processing at BEL Single Sided
More informationActivity for the IBL and SLHC upgrade
Activity for the IBL and SLHC upgrade 400 Collisions (10 35 cm -2 s -1 ) on behalf of the LPNHE Atlas Silicon R&D group The ATLAS roadmap in the LHC upgrade 5 to 15 fb -1 by 2013 Up to 100 fb -1 by 2017
More informationHigh-Speed/Radiation-Hard Optical Links
High-Speed/Radiation-Hard Optical Links K.K. Gan, H. Kagan, R. Kass, J. Moore, D.S. Smith The Ohio State University P. Buchholz, S. Heidbrink, M. Vogt, M. Ziolkowski Universität Siegen September 8, 2016
More informationMicro-sensors - what happens when you make "classical" devices "small": MEMS devices and integrated bolometric IR detectors
Micro-sensors - what happens when you make "classical" devices "small": MEMS devices and integrated bolometric IR detectors Dean P. Neikirk 1 MURI bio-ir sensors kick-off 6/16/98 Where are the targets
More informationSimulation of new P-type strip detectors with trench to enhance the charge multiplication effect in the n- type electrodes
Simulation of new P-Type strip detectors RESMDD 10, Florence 12-15.October.2010 1/15 Simulation of new P-type strip detectors with trench to enhance the charge multiplication effect in the n- type electrodes
More informationPAGE 1/6 ISSUE Jul SERIES Micro-SPDT PART NUMBER R516 XXX 10X R 516 _ 1 0 _
PAGE 1/6 ISSUE Jul-24-2017 SERIES Micro-SPDT PART NUMBER R516 XXX 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT
More informationCapacitive sensors capancdt
Capacitive sensors capancdt Measuring principle capacitive sensors - Principle of ideal plate capacitor - Two plate electrodes are represented by sensor and measurement object - Measurement on insulators
More informationStatus of ATLAS & CMS Experiments
Status of ATLAS & CMS Experiments Atlas S.C. Magnet system Large Air-Core Toroids for µ Tracking 2Tesla Solenoid for inner Tracking (7*2.5m) ECAL & HCAL outside Solenoid Solenoid integrated in ECAL Barrel
More informationSilicon Sensor and Detector Developments for the CMS Tracker Upgrade
Silicon Sensor and Detector Developments for the CMS Tracker Upgrade Università degli Studi di Firenze and INFN Sezione di Firenze E-mail: candi@fi.infn.it CMS has started a campaign to identify the future
More informationOPTICAL LINK OF THE ATLAS PIXEL DETECTOR
OPTICAL LINK OF THE ATLAS PIXEL DETECTOR K.K. Gan, W. Fernando, P.D. Jackson, M. Johnson, H. Kagan, A. Rahimi, R. Kass, S. Smith Department of Physics, The Ohio State University, Columbus, OH 43210, USA
More informationA Large Low-mass GEM Detector with Zigzag Readout for Forward Tracking at EIC
MPGD 2017 Applications at future nuclear and particle physics facilities Session IV Temple University May 24, 2017 A Large Low-mass GEM Detector with Zigzag Readout for Forward Tracking at EIC Marcus Hohlmann
More informationAldenham School. Science Department 13+ Exam - Physics SAMPLE PAPER. 20 Minutes 30 Marks
Name Teacher Aldenham School Science Department 13+ Exam - Physics SAMPLE PAPER 20 Minutes 30 Marks Q1. Lee blew across the top of paper tubes to make sounds. He investigated how changing the length of
More informationAVALANCHE PHOTODIODES FOR THE CMS ELECTROMAGNETIC CALORIMETER
AVALANCHE PHOTODIODES FOR THE CMS ELECTROMAGNETIC CALORIMETER B. Patel, R. Rusack, P. Vikas(email:Pratibha.Vikas@cern.ch) University of Minnesota, Minneapolis, U.S.A. Y. Musienko, S. Nicol, S.Reucroft,
More informationThe Detector at the CEPC: Calorimeters
The Detector at the CEPC: Calorimeters Tao Hu (IHEP) and Haijun Yang (SJTU) (on behalf of the CEPC-SppC Study Group) IHEP, Beijing, March 11, 2015 Introduction Calorimeters Outline ECAL with Silicon and
More informationA High-Granularity Timing Detector for the Phase-II upgrade of the ATLAS Detector system
A High-Granularity Timing Detector for the Phase-II upgrade of the ATLAS Detector system C.Agapopoulou on behalf of the ATLAS Lar -HGTD group 2017 IEEE Nuclear Science Symposium and Medical Imaging Conference
More informationBring the Challenge. We ll Build the Solution.
VISIONARY Bring the Challenge. We ll Build the Solution. Solving complex engineering challenges in a global market, Celera Motion advances the field and science of motion control. Our precision components
More informationTextmasterformat bearbeiten
Status of Sensors: Measurements on the AGIPD Sensors (from 1st batch to 2nd batch) Jiaguo Zhang1, Robert Klanner2, Ioannis Kopsalis2, and Joern Schwandt2 1 Photon Science Detector Group (FSDS), DESY 2
More informationhttp://clicdp.cern.ch Hybrid Pixel Detectors with Active-Edge Sensors for the CLIC Vertex Detector Simon Spannagel on behalf of the CLICdp Collaboration Experimental Conditions at CLIC CLIC beam structure
More informationReview of Silicon Inner Tracker
Review of Silicon Inner Tracker H.J.Kim (KyungPook National U.) Talk Outline Configuration optimization of BIT and FIT Silicon Sensor R&D Electronics R&D Summary and Plan Detail study will be presented
More informationLecture 11. Complex Detector Systems
Lecture 11 Complex Detector Systems 1 Dates 14.10. Vorlesung 1 T.Stockmanns 1.10. Vorlesung J.Ritman 8.10. Vorlesung 3 J.Ritman 04.11. Vorlesung 4 J.Ritman 11.11. Vorlesung 5 J.Ritman 18.11. Vorlesung
More informationEnd-of-line Standard Substrates For the Characterization of organic
FRAUNHOFER INSTITUTe FoR Photonic Microsystems IPMS End-of-line Standard Substrates For the Characterization of organic semiconductor Materials Over the last few years, organic electronics have become
More informationMulti-Wire Drift Chambers (MWDC)
Multi-Wire Drift Chambers (MWDC) Mitra Shabestari August 2010 Introduction The detailed procedure for construction of multi-wire drift chambers is presented in this document. Multi-Wire Proportional Counters
More informationAn Introduction to Electronics Systems Packaging. Prof. G. V. Mahesh. Department of Electronic Systems Engineering
An Introduction to Electronics Systems Packaging Prof. G. V. Mahesh Department of Electronic Systems Engineering Indian Institute of Science, Bangalore Module No. # 07 Lecture No. # 33 Reflow and Wave
More informationA new strips tracker for the upgraded ATLAS ITk detector
A new strips tracker for the upgraded ATLAS ITk detector, on behalf of the ATLAS Collaboration : 11th International Conference on Position Sensitive Detectors 3-7 The Open University, Milton Keynes, UK.
More informationA High Granularity Timing Detector for the Phase II Upgrade of the ATLAS experiment
3 rd Workshop on LHCbUpgrade II LAPP, 22 23 March 2017 A High Granularity Timing Detector for the Phase II Upgrade of the ATLAS experiment Evangelos Leonidas Gkougkousis On behalf of the ATLAS HGTD community
More informationDirectional Couplers / SWR detectors for 145MHz - 435MHz. Easily and cheaply made. pa0nhc. Ver. E4;
1 of 9 12/1/2008 9:46 PM
More informationCMS Tracker Upgrade for HL-LHC Sensors R&D. Hadi Behnamian, IPM On behalf of CMS Tracker Collaboration
CMS Tracker Upgrade for HL-LHC Sensors R&D Hadi Behnamian, IPM On behalf of CMS Tracker Collaboration Outline HL-LHC Tracker Upgrade: Motivations and requirements Silicon strip R&D: * Materials with Multi-Geometric
More informationFirst Results with the Prototype Detectors of the Si/W ECAL
First Results with the Prototype Detectors of the Si/W ECAL David Strom University of Oregon Physics Design Requirements Detector Concept Silicon Detectors - Capacitance and Trace Resistance Implications
More informationFigure 7 Dynamic range expansion of Shack- Hartmann sensor using a spatial-light modulator
Figure 4 Advantage of having smaller focal spot on CCD with super-fine pixels: Larger focal point compromises the sensitivity, spatial resolution, and accuracy. Figure 1 Typical microlens array for Shack-Hartmann
More informationSection 8. Curved units. Curved units
Section 8 Curved units Curved units Curved corner post... page 94 Curved base cabinet... page 95 Curved wall cabinet... page 96 Curved deep wall cabinet... page 97 Curved plinth - Joining... page 99 www.howdens.com
More informationSensor production readiness
Sensor production readiness G. Bolla, Purdue University for the USCMS FPIX group PMG review 02/25/2005 2/23/2005 1 Outline Sensor requirements Geometry Radiation hardness Development Guard Rings P stops
More informationPAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 XXX 10X. (All dimensions are in mm [inches]) R 516 _ 1 0 _
PAGE 1/6 ISSUE 15-10-18 SERIES Micro-SPDT PART NUMBER R516 XXX 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT TECHNOLOGY
More informationEM-minitower experience
EM-minitower experience flight hardware (SSDs, Fes, Trays, tower, TEM, PSA) ground I&T read-out tools (DAQ/online) system test tower test-plans developement and tuning (LAT-TD-00191) CR and V.D.G. 17.6MeV
More informationPoS(VERTEX2015)008. The LHCb VELO upgrade. Sophie Elizabeth Richards. University of Bristol
University of Bristol E-mail: sophie.richards@bristol.ac.uk The upgrade of the LHCb experiment is planned for beginning of 2019 unitl the end of 2020. It will transform the experiment to a trigger-less
More informationWide X-ray Field of View
NAOC Beijing June 25 th 2013 Wide X-ray Field of View Dick Willingale University of Leicester Scientific Motivation Soft X-ray surveys High angular resolution Large sky area Faint sources AGN, Clusters
More informationMeasurements With Irradiated 3D Silicon Strip Detectors
Measurements With Irradiated 3D Silicon Strip Detectors Michael Köhler, Michael Breindl, Karls Jakobs, Ulrich Parzefall, Liv Wiik University of Freiburg Celeste Fleta, Manuel Lozano, Giulio Pellegrini
More informationUnderground M3 progress meeting 16 th month --- Strain sensors development IMM Bologna
Underground M3 progress meeting 16 th month --- Strain sensors development IMM Bologna Matteo Ferri, Alberto Roncaglia Institute of Microelectronics and Microsystems (IMM) Bologna Unit OUTLINE MEMS Action
More informationProduct Teardown. Teardown Process
Product Teardown A product teardown process is a formal approach to learning about and modeling the functional behavior and physical components of a product. Purpose" Dissection and analysis during product
More informationTRAFTOR WINDINGS CHANGING THE RULES TOROIDAL INDUCTORS & TRANSFORMERS SOLUTIONS PROVIDER AND MANUFACTURER
TRAFTOR WINDINGS CHANGING THE RULES TOROIDAL INDUCTORS & TRANSFORMERS SOLUTIONS PROVIDER AND MANUFACTURER PRODUCT RANGE POWER INDUCTORS Toroidal technology, driven by 20 years of R&D. POWER TRANSFORMERS
More informationFlexible Hybrid Electronics Fabricated with High-Performance COTS ICs using RTI CircuitFilm TM Technology
Flexible Hybrid Electronics Fabricated with High-Performance COTS ICs using RTI CircuitFilm TM Technology Scott Goodwin 1, Erik Vick 2 and Dorota Temple 2 1 Micross Advanced Interconnect Technology Micross
More informationSurface Mount Header Assembly Employs Capillary Action
New Product Technology Surface Mount Header Assembly Employs Capillary Action Zierick s unique header assembly features capillary action to improve solder joint strength. As a result, pin retention force
More informationD. Impedance probe fabrication and characterization
D. Impedance probe fabrication and characterization This section summarizes the fabrication process of the MicroCard bioimpedance probes. The characterization process is also described and the main electrical
More informationqueensgate a brand of Elektron Technology
NanoSensors NX/NZ NanoSensor The NanoSensor is a non-contact position measuring system based on the principle of capacitance micrometry. Two sensor plates, a Target and a Probe, form a parallel plate capacitor.
More informationATLAS Phase 1 Upgrade: Muons. Starting Point: Conceptional drawing from Jörg: GRK Ulrich Landgraf
Starting Point: Conceptional drawing from Jörg: GRK2044 1 Overview Reasons for phase 1 upgrade Structure of New Small Wheel (NSW) Cooling system of NSW electronics Alignment system of NSW Micromegas operation:
More informationVertex Detector Mechanics
Vertex Detector Mechanics Bill Cooper Fermilab (Layer 5) (Layer 1) VXD Introduction The overall approach to mechanical support and cooling has been developed in conjunction with SiD. The support structures
More informationThe CMS HGCAL detector for HL-LHC upgrade
on behalf of the CMS collaboration. National Taiwan University E-mail: arnaud.steen@cern.ch The High Luminosity LHC (HL-LHC) will integrate 10 times more luminosity than the LHC, posing significant challenges
More informationThe LHCb Vertex Locator : Marina Artuso, Syracuse University for the VELO Group
The LHCb Vertex Locator : status and future perspectives Marina Artuso, Syracuse University for the VELO Group The LHCb Detector Mission: Expore interference of virtual new physics particle in the decays
More informationTechnology development for a flexible, low-cost backplane for lighting applications
IMAPS-Benelux Spring Event 2014 Technology development for a flexible, low-cost backplane for lighting applications M. Cauwe 1, A. Sridhar 2, T. Sterken 1 1 imec - Cmst, Technologiepark, Zwijnaarde, Belgium
More informationForward bias operation of irradiated silicon detectors A.Chilingarov Lancaster University, UK
1 st Workshop on Radiation hard semiconductor devices for very high luminosity colliders, CERN, 28-30 November 2001 Forward bias operation of irradiated silicon detectors A.Chilingarov Lancaster University,
More informationRoman Pots. Marco Oriunno SLAC, PPA. M.Oriunno, SLAC
Roman Pots Marco Oriunno SLAC, PPA The Roman Pot technique 1. The Roman Pot, an historically successful technique for near beam physics: ISR, SPS, TEVATRON, RICH, DESY 2. A CERN in-house technology: ISR,
More informationEffect of Corona Treatment on Spreading Behavior of UV Ink over Inkjet Printed Silver Nano-Particle Layer
Effect of Corona Treatment on Spreading Behavior of UV Ink over Inkjet Printed Silver Nano-Particle Layer Khushbeen Department of Printing Technology GJUS&T, Hisar, Haryana, India Email- khushveen12@gmail.com
More informationTEM SAMPLE-PREPARATION PROCEDURES FOR THIN-FILM MATERIALS
TEM SAMPLE-PREPARATION PROCEDURES FOR THIN-FILM MATERIALS Initial Set-Up: Heat up a hot plate to around 150-200 C Plan view Mounting/Grinding/Dimpling/Polishing: 1) Cleave a square-ish piece of sample.
More information