CLIPS & CONNECTORS. Phone:

Transcription

1 CIPS & CONNECTORS 30

2 CIPS & CONNECTORS 3 1 / / 8 11 / SOUND ISOTION CIP Description Furring Channel Sound Isolation Clip Resilmount 237 can be used in wall and ceiling applications with Studco 7/8 & 1-1/2 furring channel. MF - ETFIX DIRECT DJUSTE FURRING CHNNE CIP Clip Height Metal Thickness Clip Width x length Height of rubber* MF 1".069" / 14 gauge 1-1/8" x 4-7/8" - djustable Furring Channel clips with 4 positions at 3/16 increments to adjust Furring Channel, Eliminating packers. MFFC MET FURRING CHNNE CIP CIPS & CONNECTORS Description MFFC Furring Channel Sound Isolation Clip Metal Furring Channel Clips are used to connect furring channels to the cold rolled channel in a drywall ceiling application. The furring channel is installed at right angles to the CRC to create a grid system so the drywall can be screwed to the furring channels. M534 Description M534 Furring Channel Sound Isolation Clip This innovative design let you adjust your suspended ceiling during the installation process. This suspension hanger has been U Tested and approved to carry up to 500 S. / Clip* *Clip must be used with M21 5mm Wire M74 M74 M47 M74 / M47 Description 5mm Galvanized Straight Rod racket 5mm Right ngle Galvanized Rod racket M47 The M74 bracket is a straight bracket that is used to accommodate to M21 5mm wire rod at the ceiling connection. The 90 Degree M47 bracket is used to accommodate to M21 5mm wire rod at the ceiling connection. 31

3 CIPS & CONNECTORS CIPS & CONNECTORS CIPS & CONNECTORS - JOIST HNGER M21 Description M21 5mm Galvanised Wire Rod This rod is 5mm is used in applications where suspension from the ceiling above is needed. This soft Galvanized rod has been U tested as an assembly with the M534 spring hanger. Cannot be substituted with 3/16 rod. RIDE JOIST HNGER Description H W JH Single 6 2-1/16 2 JH Double 6 4-1/8 2 JH /8 flg /16 2 JH Single 8 2-1/16 2 JH Double 8 4-1/8 2 JH /8 flg /16 2 JH Single /16 2 JH Double /8 2 JH Single /16 2 JH Double /8 2 JH Single /16 2 JH Double /8 2 JH Single /16 2 CIPS & CONNECTORS - WE STIFFENER Studco uilding Systems ridle Joist Hangers are made from heavy duty 97mil (12ga) 50 KSI galvanized steel. They come in a range of Standard sizes from 6 to 16 in singles and doubles. Custom sizes are available upon request. ll standard size bridle hangers are in stock ready for fast delivery. They are an easy to use joist hanger designed to attach ight Gauge Metal Joists to concrete block, lumber topped plates and steel beams. The connection of light gauge joists is made simple and easy for the installer to construct floor and roof conditions for the construction industry. WE STIFFENER Mil Joist Size (w) ength WS-4X /4 WS-4X /4 WS-4X /4 WS-4X /4 WS-4X /4 WS-4X /4 Studco uilding Systems Web Stiffeners are designed to strengthen the webs of Joists to prevent web crippling. They come in various lengths from 5-3/4 to 15-3/4 to suit the Joist width for easy installation by the contractor. They are produced out of prime galvanized 50ksi 54 mil steel. Web Stiffeners are used on the inside or back side of the joist in point load or extra load conditions, under walls or where point loads are requested to satisfy engineering needs. 32

4 t Studco, we are dedicated to providing our customers with the best products, however, we cannot manufacture all of them ourselves. We partnered with Simpson Strong-Tie to provide our customers with the best clips and connectors on the market for steel-studs. This is what we are offering: YPSS FRMING SIDE-CIP CONNECTORS The SC/MSC side-clip connectors are high performance connectors for bypass framing applications designed to reduce design time and overall installed cost. Various anchorage methods have been tested, and the resulting allowable loads eliminate the need to design connector anchorage. The SC/MSC can accommodate applications that typically require two parts with a single connector, reducing material and labor cost. These connectors are manufactured in five different lengths to accommodate a variety of stand-off conditions and steel-stud sizes. SC/MSC SIDE-CIP CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) SC (16) 3-1/2 1-1/2 4 SC (16) 5-1/2 1-1/2 4 SC (16) 7-1/2 1-1/2 4 SC (16) 9-1/2 1-1/2 4 SC (16) 11-1/2 1-1/2 4 Provides a full 1" of both upward and downward movement The precision-manufactured shouldered screws provided with the SC/MSC connector are designed to prevent overdriving and to ensure the clip functions properly Strategically placed stiffeners, embossments and anchor holes maximize connector performance Simpson Strong-Tie No-Equal stamps mark the center of the slots to help ensure correct shouldered-screw placement. Material: SC 54 mil (16 ga.); MSC 68 mil (14 ga.) CIPS & CONNECTORS SC43.5 SC45.5 SC47.5 SC49.5 SC411.5 IDC DRIFT-CIP CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) IDC (12) 5-1/2 3-1/2 4 IDC45.5 The IDC45.5 drift-clip connector is used to secure bypass stud framing to the edge of a slab. The connector will accommodate 1" of lateral drift in each direction and 1" of upward and downward vertical deflection. Tested load values are provided for anchorage to a steel edge angle using #12 x 1 1/4" Strong-Drive X arge-head Metal screws. Horizontal embossments and corner gussets optimize performance in the F2 load direction. Precision-manufactured shouldered screws provided with the IDC connector are designed to prevent overdriving and to ensure the clip functions properly Simpson Strong-Tie No-Equal stamps mark the center of the slots to help ensure correct shouldered-screw placement. Material: 97 mil (12ga.) 33

5 YPSS FRMING SIDE-CIP CONNECTORS CIPS & CONNECTORS Ideal for high-seismic areas, Simpson Strong- Tie SC connectors are the optimal solution for slide-clip bypass framing. SC clips are often welded to the structure in high-seismic zones, but they also feature anchorage holes so that concrete screws or powder-actuated fasteners can be used to attach the clip to the structure. In addition to anchorage versatility, the SC clips include "No-Equal" stamps at the center of the slots to ensure proper shouldered screw placement. Embossments in the bendline provide increased strength and stiffness in the F1 and F2 load directions, but are positioned towards the center of the clip so that 1 1/2" long welds can be applied at the top and bottom of the clip. SC connectors are manufactured using heavy-duty 10- and 12-gauge steel to provide exceptional resistance to in-plane seismic load. SIMPSON STRONG-TIE SC CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) SC /2 7/8 1-1/4 SC /8 1-1/2 SC /8 1-1/2 The clips come in lengths of 3 1/2", 6" and 8" for use with 3 5/8"," and 8" studs respectively The maximum stand-off distance is 1" for 3 5/8" studs and 1 1/2" for 6"and 8" studs Provides a full 3/4" of both upward and downward deflection Prepunched large-diameter anchor holes accommodate 1/4" -diameter concrete screws like the Simpson Strong-Tie Titen HD Prepunched small-diameter anchor holes accommodate powderactuated fasteners like the 0.157"-diameter Simpson Strong-Tie PDPT or the #12 self-drilling Simpson Strong-Tie Strong-Drive X arge-head Metal screw Precision-manufactured shouldered screws, provided with SC connectors, are designed to prevent overdriving and to ensure the clip functions properly Material: SC32/62 97 mil (12 ga.); SC mil (10 ga.) SC32 SC62 SC82 SCH Introducing the Simpson Strong-Tie SCH slideclip connector an ideal solution for panelized or stick-frame construction where cold-formed steel bypass framing anchors to the top of a floor slab or the bottom flange of a steel beam. The SCH connector has been developed and tested to accommodate several different anchorage methods to concrete and steel. The connector even features a wider support leg to decrease eccentricity on anchors and provide a variety of anchorage options. The included SCVS slider provides superior rotational support to the vertical leg of the SCH connector, helping to improve the buckling performance of the anchored leg. SCH SIDE-CIP CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) SCH /4 2-3/4 4-15/16 Provides a full 1" of both upward and downward movement Tabulated design values for anchorage help mitigate risk and provide ease of specification No need for left or right parts either face of anchorage leg can be used against the support ccommodates stand-off distances up to 4 3/4" Can be used with 3 5/8", 4", 6" and 8" studs Pre-punched anchor holes accommodate 1/4"-diameter Titen HD or other 1/4"-diameter concrete screw anchors, and 0.157"-diameter powder-actuated fasteners such as the Simpson Strong-Tie PDPT-62KP Pre-punched anchor holes also eliminate the need for pre-drilling and help ensure accurate anchor placement 34

6 YPSS FRMING SIDE-CIP CONNECTORS SS3.518 RIDGING ND RCING CIPS SUH / MSUH / SUH The latest innovations from Simpson Strong-Tie for cold-formed steel (CFS) framing are the SUH and MSUH wall stud bridging connectors. Through enhanced product design, these connectors can reduce labor costs and increase installation productivity. SUH brididging connectors offer a lower-cost option to our popular SUH/MSUH u-channel bridging connectors. The SUH connector provides all the installation benefits of the SUH/MSUH connectors, and is suitable for many wind-bearing and load bearing situations where the load demand is light to moderate. SS YPSS FRMING SIDE-CIP STRUT CONNECTOR Thickness mil (ga.) (in.) (in.) (in.) SS (16) /8 3-1/2 The SS connector is a versatile strut connector that is commonly used at the bottom of a steel beam to accommodate large stand-off conditions. It accommodates 1" of upward and 1" of downward movement. Material: 54 mil (16 ga.) SUH/MSUH/SUH RIDGING CIP Thickness mil (ga.) SUH (20) MSUH (18) SUH (14) Installed easily by a single installer Many applications require only one screw Tested to include stud-web strength and stiffness in the tabulated design values Design values ensure compliance with ISI S100 Sections D3.2.1 and D3.3 for axially and laterally loaded studs Flexible design solutions for web thicknesses of 33 mil (20 ga.) through 97 mil (12 ga.) and stud sizes from 3 5/8" to 8" Compact profile allows standard 1 5/8" studs to be sistered directly against adjacent studs MSUH accommodates back-to-back built-up members ranging from 33 mil (20 ga.) to 54 mil (16 ga.) SUH ccommodates 3-5/8", 6" and 8" studs in thickness of 33 mil (20 ga.) through to 54 mil (16ga.) CIPS & CONNECTORS DC DRYW RIDGING CONNECTOR DC Patented design allows for 1 or 2 screw installation of the DC, significantly reducing labor and material cost. The first and only connector load rated for 3/4" u-channel, the DC joins the SUH line of bridging connectors tested as a system, ensuring that published design capacities capture the influence of stud web depth and thickness. Most applications require only a single screw Designed for 3/4" u-channel to fit smaller web knockouts common to drywall studs Compatible with drywall stud depths of 3 5/8" and 6" with 1 1/2" wide knockouts Material: 33 mil (20 ga.) carbon steel 35

7 SPCER RCERS CIPS & CONNECTORS Simpson Strong-Tie introduces the SR and DR spacer bracers for cold-formed steel construction. These spacer bracers reduce the installed cost of cold-formed steel stud walls by enabling faster stud layout while minimizing the need for bridging clips. The DR is used for interior walls to allow for quicker drywall attachment, while the SR is designed for structural exterior walls. oth products provide bracing along the length of the stud, and for head-of-wall slip conditions. The SR and DR also come with prepunched slots that eliminate the need to use bridging clips with on-module studs. The SR and DR spacer bracers come with bracing load data based on assembly testing, thus mitigating risk for designers and maximizing confidence in design specs. In fact, the SR and DR are the only spacer bracers on the market with tabulated design values based on assembly tests. SR / DR SPCER RCERS (in.) (in.) (in.) SR 50-3/4 2-1/4 1/2 DR 50-3/4 1-5/8 1/2 SR and DR have patent-pending precision-engineered prepunched slots strategically located to enable 12", 16" and 24" on-center stud spacing and can be used to space the studs without having to mark the top track for layout The SR will accommodate 3 5/8" and 6" studs in thicknesses of 33 mil (20 ga.) thru 68 mil (14 ga.) The DR will accommodate 2 1/2", 3 5/8" and 6" studs in thicknesses of 15 mil (25 ga. EQ) through 33 mil (20 ga.) Prepunched holes in the SR provide rapid screw installation when spacer bracer splices are needed for axial load-bearing studs In off-layout or end-of run conditions, the hat-section profiles enable clip attachments to the stud with Simpson Strong-Tie SSC or RC connectors SR DR FS YPSS FRMING FIXED-CIP STRUT CONNECTOR FS YPSS FRMING FIXED-CIP STRUT CONNECTOR Thickness mil (ga.) (in.) (in.) (in.) FS (16) /2" 1-5/8 FS3 The FS connector is the fixed-clip version of our popular SS slide-clip strut connector. The FS is commonly used at the bottom flange of a steel beam to accommodate large stand-off distances for bypass curtainwall studs. Material: 54 mil (16ga.) 36

8 SCW HED-OF-W SIDE-CIP CONNECTOR SCW3.25 DTC SCW5.5 SCW HED-OF-W SIDE-CIP CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) SCW (16) 3-1/4 1-1/2" 4 SCW (16) 5-1/2" 1-1/2" 4 The SCW connectors offer 1" of upward and 1" of downward movement. They are primarily used in head-of-wall applications that require vertical movement relative to the structure. SCW connectors are often used to strengthen window and door jambs for projects that utilize slip track. DTC HED-OF-W SIDE-CIP CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) DTC 43 (18) 2-3/4 1-7/8 2-1/2 DTC clips are a cost-effective solution for light-duty, head-of-wall slide clip applications. The 1 5/8" slot will allow ¾" movement in each direction. Material: 43 mil (18ga.) CIPS & CONNECTORS JOIST CIPS SJC connectors have been specifically designed for various CFS joist, rafter and underside of metal-deck applications. The unique clip dimensions enable easy installation on the open side of joists and rafters with up to 3 1/2" flanges and return lips up to 3/4". For metal-deck applications, the pre-punched 3 8" holes easily accommodate 6", 8", 10" and 12" on-center metal-deck flutes. SJC JOIST CIPS Thickness mil (ga.) (in.) (in.) (in.) SJC /4 4-1/2 2-3/16 SJ /4 4-1/2 2-3/16 Pre-punched holes reduce installation cost by eliminating predrilling Intuitive fastener hole positions ensure accurate clip installation in accordance with design, support a wide range of design and application requirements and provide installation flexibility ngle lengths accommodate either hard-side or soft-side attachment for joists with return lips up to 3/4" 4 1/2" leg length enables soft-side connections for joists with flanges up to 3 1/2" lso accommodates kicker-to-metal-deck applications Material: SJC 68 mil (50 ksi); MSJC 97 mil (50 ksi) SJC8.25 SJC

9 FIXED CIPS CIPS & CONNECTORS The FC clip is an economical, high-performance fixedclip connector that can be used for a variety of framing applications. It is rated for tension, compression, shear and in-plane loads and offers the Designer the flexibility of specifying different screw and anchorage patterns that conform to desired load levels. Typical FC Installation at ypass Framing FC FIXED-CIP CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) FC / /2 FC / /2 FC / /2 FC / /2 FC / /2 Rated for tension, compression and shear loads Provides design flexibility with varying screw and anchorage patterns that achieve different load levels Strategically placed stiffeners, embossments and anchor holes maximize connector performance Material: SC 54 mil (16 ga.); MSC 68 mil (14 ga.) FC43.5 FC45.5 FC47.5 FC49.5 FC411.5 Ideal for high-seismic areas, Simpson Strong-Tie FC connectors are the optimal solution for fixedclip bypass framing. FC clips are often welded to the structure in high-seismic zones, but they also feature anchorage holes so that concrete screws or powder-actuated fasteners can be used to attach the clip to the structure. In addition to anchorage versatility, the FC clips features prepunched screw holes for the framing attachment eliminating the need for predrilling holes or worrying that fastener placement (like the 0.157"-diameter Simpson Strong-Tie PDPT or #12 self-drilling Simpson Strong-Tie) doesnt match the designer specifications. FC connectors are manufactured using heavy-duty 10- and 12-gauge steel to provide exceptional resistance to in-plane seismic load. SIMPSON STRONG-TIE FC CONNECTORS Thickness mil (ga.) (in.) (in.) (in.) FC /2 2 5 FC FC The clips come in lengths of 3 1/2", 6" and 8" and are intended to be used with 3 5/8", 6" and 8" studs, respectively The maximum stand-off distance is 1" for 3 5/8" studs and 1 1/2" for 6" and 8" studs Embossments in the bendline provide increased strength and stiffness in the F1 and F2 load directions, but are positioned towards the center of the clip so that 1 1/2" long welds can be applied at the top and bottom of the clip Prepunched large-diameter anchor holes accommodate 1/4"-diameter concrete screws like the Simpson Strong-Tie Titen HD screw anchor Prepunched small-diameter anchor holes accommodate powder-actuated fasteners Strong-Drive X arge-head Metal screw Material: FC32/62 97 mil (12 ga.); FC mil (10 ga.) FC32 FC62 FC82 38

10 UTIITY CIPS The RC rigid connector angle is a general-purpose clip angle that can be used for miscellaneous head/sill connections to jamb studs, jamb stud reinforcement at track, u-channel bridging, studblocking, by-pass curtainwall framing and more. With pre-punched holes for fastener attachment, this -shaped clip offers time and labor savings on the job. The RC is available in 16-, 14- and 12-gauge. RC RIGID CONNECTOR Thickness mil (ga.) (in.) (in.) (in.) RC223/54 54 (16) RC223/68 68 (14) RC223/97 97 (12) RC225/54 54 (16) RC225/68 68 (14) RC225/97 97 (12) RC227/54 54 (16) RC227/68 68 (14) RC227/97 97 (12) RC333/54 54 (16) RC333/68 68 (14) RC333/97 97 (12) RC335/54 54 (16) RC335/68 68 (14) RC335/97 97 (12) Use with miscellaneous header/sill connections to jamb studs, jamb stud reinforcement at track, u-channel bridging, stud-blocking, bypass curtainwall framing and more Easy to install, with pre-punched holes for quick and accurate fastener attachment CIPS & CONNECTORS JOIST CIPS, S and S/S angles are load-rated, providing the correct thickness and number of fasteners for the specifier compared with field-fabricated clip angles. These angles also have well-defined fastener locations, and testing ensures that the tabulated load values account for connection eccentricities. The connectors are general utility reinforcing angles with multiple uses. S/S and S connectors are skewable and can be used to attached members intersecting at angles. SJC JOIST CIPS Thickness mil (ga.) (in.) (in.) (16) 1-3/8 2-3/ (16) 1-3/8 2-3/ (16) 1-3/8 2-3/ (16) 1-3/8 2-3/8 S50 43 (18) 1-3/8 2-3/8 S70 43 (18) 1-3/8 2-3/8 S/S50 43 (18) N N S/S70 43 (18) N N Material: 54 mil (16 ga.); S/S and S 43 mil (18 ga.) 39

11 UTIITY CIPS CIPS & CONNECTORS SSC connectors are versatile utility clips ideal for a variety of stud-to-stud and stud-to-structure applications in cold-formed steel construction. The clips have been designed to enable easy installation on the open side of studs or joists with flanges up to 3" long and return lips up to 3/4". wide pattern of strategic fastener locations allows the SSC to accommodate a variety of traditional and custom designs. SSC Installation with Carried Member Fasteners in Outer Row SSC STEE-STUD CONNECTOR (in.) (in.) (in.) SSC / /4 MSSC /4 N/ N/ SSC /4 N/ N/ SSC / /4 MSC /4 N/ N/ SC /4 N/ N/ SSC / /4 MSC /4 N/ N/ Pre-punched holes reduce installation cost by eliminating pre-drilling Intuitive fastener hole positions ensure accurate clip installation in accordance with design, support a wide range of design and application requirements and provide installation flexibility ngle lengths accommodate either hard-side or soft-side attachment for studs and joists with return lips up to 3/4" (SSC2.25 clips will accommodate 2" wide flange and 5/8" stiffener lips.) 4" leg length enables soft-side connections for studs and joists with flanges up to 3" (SSC2.25 clips will accommodate 2" wide flange and 5/8" stiffener lips.) lso suitable for u-channel bridging SSC2.25 SSC4.25 SSC6.25 SFC connectors are a low-cost, multi-use utility clips for light to moderate loading conditions in CFS studto-stud and stud-to-structure applications where long leg lengths are not required. SFC2.25 SFC6.25 SFC4.25 SFC STEE FRMING CONNECTOR (in.) (in.) (in.) SFC /4" 1-3/4 7/8 SFC /4" N/ N/ SFC /4" 1-3/4 1-1/2 SFC /4" N/ N/ SFC /4" 1-3/4 1-1/2 SFC /4" N/ N/ Reduced number of screws reduces installation cost Pre-punched holes reduce installation cost by eliminating predrilling Intuitive fastener hole positions ensure accurate clip installation in accordance with design, support a wide range of design and application requirements and provide installation flexibility In soft-side stud installations, SFC will not interfere with stud lips up to 3/4" long (SFC2.25 clips will accommodate 5/8" long stiffener clips) lso suitable for U-channel bridging 40

12 KNEEW CONNECTORS The Simpson Strong-Tie RCKW rigid connectors have been developed to resist overturning moment at the base of exterior kneewalls and parapets as well as interior partial-height walls. These connectors offer a unique anchor-hole pattern that permits anchorage to both concrete and structural steel, with the larger hole designed to accommodate 1/2"-diameter concrete screws such as the Simpson Strong-Tie Titen HD. The RCKWS is a heavy 171 mil (7 ga.) stiffener that nests onto the RCKW clip. The screw holes and anchor holes in the stiffener line up with those in the RCKW clip, making fastener and anchor installation a snap. The RCKW clip and RCKWS stiffener are sold separately. Typical FC Installation at ypass Framing nchorage legs incorporate stiffened flanges, improving overturning moment resistance arge-diameter anchor hole accommodates 1/2"-diameter concrete screws and wedge anchors, such as the Simpson Strong-Tie Titen HD heavy-duty screw and the Strong-olt 2 wedge anchor dditional smaller-diameter anchor holes enable attachment to structural steel through use of #12 self-drilling screws ttachment to CMU can be achieved with use of Titen concrete and masonry screws For the RCKWS: 171 mil (7 ga.) stiffeners are secured to the RCKW clip with screws, optimizing overturning moment resistance and stiffness RCKW RIGID CONNECTORS (in.) (in.) (in.) RCKW /2 2-1/4 RCKW /2 3-1/2 2-1/4 RCKW /2 3-1/2 2-1/4 RCKW3S 3 1-1/2 N/ RCKW5.5S 5-1/2 1-1/2 N/ CIPS & CONNECTORS RCKW3 RCKW5.5 RCKW7.5 RCKW3S RCKW5.5S Fill 8 holes as shown MSSC RIGID CONNECTORS Thickness mil (ga.) MSSCKW MSSCKW MSSC connectors are designed to work in tandem with Simpson Strong-Tie P1/2-3 bearing plates to provide solutions for moment-resisting kneewall applications. Fill 12 holes as shown One simple custom hole pattern for each stud size simplifies specification and installation. 3/8" diameter anchor bolt location enables easy tool access. Material: MSSC 97 mil (50 ksi); P 229 mil (33 ksi) 41