GRANDIO G R E E N H O U S E S GRANDIO ASCENT 8x12, 8x16, 8x20, 8x24 KITS. Grandio Ascent 8x24 Shown In Image GREENHOUSE USER MANUAL

Transcription

1 GRANDIO G R E E N H O U S E S 05 GRANDIO ASCENT 8x, 8x6, 8x0, 8x4 KITS Grandio Ascent 8x4 Shown In Image GREENHOUSE USER MANUAL 03 Grandio Greenhouses, Backyard Living Source Inc. All rights reserved 05 Extendable Models

2 GRANDIO G R E E N H O U S E S IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY Dear Valued Customer, We would like to congratulate you on your new Grandio Greenhouse purchase. We are confident that you have made the right decision in choosing Grandio. Our greenhouses are made with high quality aluminium and polycarbonate and will last for many garden seasons to come. Please take the time to carefully read this instruction manual for an easier and more enjoyable assembly experience. Cheers! Grandio Greenhouses Save this owner s manual for future reference and if you need our help. CONTACT OUR CUSTOMER SERVICE DEPARTMENT at: Hours: 8:30a.m.-5:00p.m. Monday through Friday (Mountain Standard Time) Backyard Living Source 9543 W. Emerald St., Suite 0 Boise, ID Before you begin, take time to complete this check list. Take inventory of all parts using the parts list at the back of this manual on pages The base kit parts list is at the front on page and 3. Be cautious where you place the polycarbonate panels as they will burn grass or plants if left on top of them in direct sunlight. Note that clear film side of panels should always face the sun and white film side faces inside greenhouse. Panels may scratch easily so be careful what you clean them with. Plan out when and where you are going to place the greenhouse, we recommend that you place it in an area that will receive direct sunlight and will be protected from the wind as much as possible It will take at least () people to put the greenhouse together. Before your build, make sure you are allowed to build it! Consult all building codes, as well as City or Municipality ordinances and HOA s, as you may need a permit or documentation before you build. Contact your insurance company to make sure your Grandio Greenhouse will be covered on your policy. Call your local utilities companies before digging. Do not attempt to begin construction on a windy day. Your greenhouse should be built on a flat level surface allowing for drainage. Read this entire manual to get familiar with all pieces and parts prior to beginning assembly. Follow the steps outlined in the order presented!

3 IMPORTANT! SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction materials. Before beginning assembly, read the instructions and identify all parts using the hardware identifier and parts list on pages Complete assembly and proper usage are essential to reduce the risk of accident or injury when using your Grandio Greenhouse. CAUTION: Do not leave polycarbonate panels laying on grass or leave in the sun or extreme heat, keep in a cool dry place until they are to be installed!! (May cause burning to plants or grass if left directly on top of them, also may damage panels due to the protective film adhering to panels.) Panels may scratch easily. Do Not use solvent cleaners. Each of the polycarbonate panels have a clear film side that should always face the sun, and an white film side which faces inside. The clear side has a UV coating and we recommend marking a small x on a corner of each panel to determine which side has the UV Coating as you cannot visually determine with your eye in the case of future disassembly. Due to shipping, the grooves of some of the aluminum profiles may be too small to insert into the polycarbonate sheet, you may carefully use a screwdriver to pry the framework open so the polycarbonate sheet can be inserted smoothly. Do not use or store hot objects such as grills, blow torches, welding equipment, etc. in or near your greenhouse. Do not allow children or pets to play in greenhouse or in the set up area until assembly is complete. If using a ladder during assembly, use extreme caution. A clean level surface is essential to maintaining the solid integrity of the structure, Install the base correctly as described in manual. Please anchor the greenhouse down to a firm and level base. TOOLS YOU WILL NEED FOR ASSEMBLY Tape Measure Step Ladders Safety Glasses Level Work Gloves Drill Is Helpful Carpenter Square Permanent Marker Knee Pads At Least Adults Masking Tape Folding Utility Table GRANDIO TIP When you see this icon pay special attention to the helpful tips we have provided that will make installation more efficient.

4 GRANDIO G R E E N H O U S E S ASSEMBLY INSTRUCTION STEPS PREPARE FOR ASSEMBLY STEP ONE: BASE ASSEMBLY STEP TWO: FRONT ASSEMBLY STEP THREE: BACK ASSEMBLY STEP FOUR: MIDDLE ASSEMBLY STEP FIVE: EXTENSION ASSEMBLY STEP SIX: INTERIOR SUPPORT ASSEMBLY STEP SEVEN: DOOR ASSEMBLY Introduction... Safety Instructions... Prepare For Assembly...4 Box Configurations...5 Diagrams of Assembled Grandio Ascent Sizes 8x8, 8x, 8x6, 8x0, 8x Base Kit Assembly Information... Base Kit Parts Lists x Base Kit...4 8x6 Base Kit...5 8x0 Base Kit...6 8x4 Base Kit...7 Base Kit Assembly and Installation Front Assembly...-6 Back Assembly Middle Assembly Extension Assembly x0 and 8x4 Extension Assembly Extension Assembly Continued Interior Roof Supports...59 Door Assembly GRA-ASC-8A Parts List GRA-ASC-8P Parts List...69 GRA-ASC-4X Parts List GRA-ASC-8XA Parts List GRA-ASC-8XP Parts List...75 Warranty

5 EAVE HEIGHT PREPARE FOR GREENHOUSE ASSEMBLY IMPORTANT: BASE KIT ASSEMBLY & GREENHOUSE PLACEMENT Before assembling your new greenhouse, a proper foundation must be prepared. A number of anchoring options are acceptable, based on wind and ground conditions in your area. 8X GRANDIO ELITE BARN STYLE GREENHOUSE DIMENSIONS Pre-read pages -0 for base kit assembly information. Go to for foundation ideas and tour our online learning center for tips, tricks and videos for putting your greenhouse together. IMPORTANT: POLYCARBONATE PANELS The UV-Protected side is covered with transparent film and must face toward the sun. The side covered in white film will always face the interior of the greenhouse. We suggest you peel all film off completely prior to assembly and use a permanent marker to place a small X on the lower right corner of each panel on the transparent side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The X is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp. Polycarbonate Panels Transparent Film Opal White Film Sun ROOF PEAK HEIGHT BASE 3 / X 44 LEFT SIDE 8X 4 DOOR / 4 GUTTERS FRONT WIDTH *SEE BASE KIT ASSEMBLY SECTION FOR ALL GREENHOUSE BASE DIMENSIONS ON PAGES / 6 7 / 6 DOOR HEIGHT 4

6 EXTENSION KIT BOX CONFIGURATIONS We recommend that you lay all of your boxes out as shown below for an organized assembly. Locate your greenhouse size and situate near your assembly site. We suggest you lay the parts out on a tarp so you do not lose items in the grass or dirt near your building site. *See the reference diagrams on pages 6-0 for more information about how the parts will go together and what makes up each section for the assembly. GRANDIO ASCENT 8X GRANDIO ASCENT 8X6 Back Ascent 4 Extension GRA-ASC-4X Aluminum Extrusions, Hardware Bag, 4 Base Extension, Roof Vent, Snow Load Extension Supports, Polycarbonate Panels for 4 Extension. + Ascent 8 x8 GRA-ASC-8A Aluminum Extrusions, Hardware Bag, Front, Back and Doors. GRA-ASC-8P Polycarbonate Panels 8x8 Base Kit GRA-ASC-8 Base kit & hardware Front Back Ascent 8 Extension GRA-ASC-8XA Aluminum Extrusions, Hardware Bag, 8 Base Extension, Roof Vents, Snow Load Extension Supports. GRA-ASC-8XP Polycarbonate Panels For The 8 Extension + Ascent 8 x8 GRA-ASC-8A Aluminum Extrusions, Hardware Bag, Front, Back and Doors. GRA-ASC-8P Polycarbonate Panels 8x8 Base Kit GRA-ASC-8 Base kit & hardware Front GRANDIO ASCENT 8X0 GRANDIO ASCENT 8X4 Back Ascent 4 Extension GRA-ASC-4X Aluminum Extrusions, Hardware Bag, 4 Base Extension, Roof Vent, Snow Load Extension Supports, Polycarbonate Panels for 4 Extension. Ascent 8 Extension GRA-ASC-8XA Aluminum Extrusions, Hardware Bag, 8 Base Extension, Roof Vents, Snow Load Ascent 8 x8 GRA-ASC-8A Aluminum Extrusions, Hardware Bag, Front, Back and Doors. Extension Supports. + + GRA-ASC-8P Extension Supports. + Extension Supports. + GRA-ASC-8XP Polycarbonate Panels For The 8 Extension Polycarbonate Panels 8x8 Base Kit GRA-ASC-8 Base kit & hardware Front Back Ascent 8 Extension GRA-ASC-8XA Aluminum Extrusions, Hardware Bag, 8 Base Extension, Roof Vents, Snow Load GRA-ASC-8XP Polycarbonate Panels For The 8 Extension Ascent 8 Extension GRA-ASC-8XA Aluminum Extrusions, Hardware Bag, 8 Base Extension, Roof Vents, Snow Load GRA-ASC-8P Polycarbonate Panels For The 8 Extension Ascent 8 x8 GRA-ASC-8A Aluminum Extrusions, Hardware Bag, Front, Back and Doors. GRA-ASC-8P Polycarbonate Panels 8x8 Base Kit GRA-BAS-8 Base kit & hardware Front 5

7 LEFT SIDE 60A-B BA-S L08A Y 60D 60D Y Y Y L08B-X 603B 603B L08B-X DIAGRAM SHOWS THE ASSEMBLED (8 x8 BASIC CONFIGURATION) (GRA-ASC-8A & GRA-ASC-8P & GRA-BA-8) 8x8 ASCENT KIT INCLUDES, FRONT, BACK, BASE AND SIDES. 60A-B RIGHT SIDE 60 L08B 60 Y- Y4- Y4- Y BA-S 60B L08C 60B 60B 60C B 60B L08C 60B BA-S 603B/66 Y9 603A 603C B 60B 68 L 68 Y8 Y3- Y3- Y8 Y9 603B/66 60B Y- L08D 603B 63A 63A 6 Y5 Y5 6 Y- L08D 6-L 6-R 60B LEFT SIDE L08A-X 60A-FL 604-L 604-R Y Y5 Y5 Y L08A-X 60A-FR RIGHT SIDE 63B 63B BA-S FRONT 69 Outside View 6

8 (4 Extension Side) (GRA-ASC-4X) Ascent 4 Side Extension Includes Base (8 x8 Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BA-8) 8x8 Ascent Includes Front, Back, Base, and Sides 60 L08A BA-S 60D 60D Y Y Y 60A-B Y 60A-B L08B-X 603B 603B L08B-X L08B 60 Y- Y4- Y4- Y C 60B 60B 60 60B 60B L08C 603B/66 L08C 60B 60B 60 BA-S Y9 Y B L08C BA-S 67 60B L08C 67 BACK In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. BA-S 603B/66 BA-S 60B 60B 65 RIGHT SIDE In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. (4 Extensions Side) 4X Ascent Side Y9 DIAGRAM SHOWS THE ASSEMBLED 8X GRANDIO ASCENT THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS AN 4 FOOT EXTENSION KIT Outside View 7 603B/66 68 Y9 Y8 603C 603A 8x8 Ascent Side Y8 L 60B 60B Y3- Y3-60B 60B 63A 63A Y- 6 Y5 Y5 6 Y- L08D L08D 603B 6-L 6-R 604-L 604-R L08A-X Y Y L08A-X 60A-FL Y5 Y5 60A-FR LEFT SIDE In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. 63B 63B 69 FRONT In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. BA-S

9 (8 Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8 Side Extension includes Base (8 x8 Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BA-8) 8x8 Ascent Includes Front, Back, Base, and Sides BACK In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. L08A BA-S 60D 60D Y Y Y Y L08B-X 603B 603B L08B-X 60A-B L08B 60A-B Y- Y4- Y4- Y C 60B 60B Y L 60B 68 Y8 603A 603C 65 60B 60B Y3- Y3- BA-S 63A 63A Y- 6 Y5 Y5 6 Y- L08D L08D 603B 6-L 6-R L08C 60B 604-L 604-R L08A-X Y Y L08A-X 60A-FL Y5 Y5 60A-FR 63B 63B 603B/66 Y9 69 BA-S 60 60B 60 60B L08C BA-S 60B 603B/66 Y9 60B L08C 60B 603B/66 Y9 60B 68 Y8 BA-S 60B 60 60B L08C BA-S 60B 603B/66 Y9 60B Y8 DIAGRAM SHOWS THE ASSEMBLED 8X6 GRANDIO ASCENT THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS AN 8 FOOT EXTENSION KIT Outside View FRONT In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. LEFT SIDE In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. RIGHT SIDE In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. 8x8 Ascent Side (8 Extension Side) 8X Ascent Side 8

10 (4 Extension Side) (GRA-ASC-4X) Ascent 4 Side Extension Includes Base (8 Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8 Side Extension includes Base (8 x8 Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BA-8) 8x8 Ascent Includes Front, Back, Base, and Sides BACK In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. L08A BA-S 60D 60D Y Y Y Y BA-S L08C L08B-X 603B 603B L08B-X 60A-B L08B 60A-B 60B Y4- Y4- Y- Y- 60B 603B/ C L08C 60 BA-S Y9 Y8 60B AZ 60B 67 AZ B 60B BA-S L08C L08C BA-S 67 60B 60B 603B/ Y9 Y8 Y9 603B/66 Y8 60B 60B DIAGRAM SHOWS THE ASSEMBLED 8X0 GRANDIO ASCENT THE BOX CONFIGURATION IS AN ELITE 8X8 PLUS AN 8 FOOT AND A 4 FOOT EXTENSION KIT Outside View AZ AZ B 60B 603C 603A BA-S L08C L08C 60B 60B Y3- Y3- L 60B 63A 63A 65 Y- 6 Y5 Y5 6 Y- L08D L08D B/ B 6-L 6-R 603B 68 Y8 Y8 Y9 604-L 604-R Y Y Y5 Y5 60B 60A-FL L08A-X L08A-X 60A-FR 63B 63B 60B 603B/66 Y9 60B BA-S RIGHT SIDE In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS FRONT In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. BA-S LEFT SIDE In boxes GRA-ASC-8A and GRA-ASC-8P, the base for 8x8 is all in GRA-BAS-8. (4 Extensions Side) 4X Ascent Side (8 Extension Side) 8X Ascent Side 9 8x8 Ascent Side

11 (8 Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8 Side Extension includes Base (8 Extension Side) (GRA-ASC-8XA & GRA-ASC-8XP) Ascent 8 Side Extension includes Base (8 x8 Original Kit) (GRA-ASC-8A & GRA-ASC-8P & GRA-BA-8) 8x8 Ascent Includes Front, Back, Base, and Sides 60 BACK L08A BA-S 60D 60D Y Y Y Y B L08B-X 603B 603B L08B-X 68 Y C 603A 60B 60B Y3- Y3- L 63A 63A Y- 6 Y5 Y5 6 Y- 65 L08D L08D B 6-L 6-R 603B 68 Y8 604-L 604-R Y Y Y Y5 Y5 60A-FL L08A-X L08A-X 60A-FR 63B 63B FRONT 60 60B L08C 60B 60A-B 603B/66 Y9 L08B 60B 60A-B LEFT SIDE 60 Y4- Y4- Y- 60B BA-S L08C 60B 603B/66 Y9 60B BA-S 68 Y- BA-S L08C 60B C Y8 603B/66 Y9 60B 60 60B L08C BA-S 60B 603B/66 Y B 60B 60 AZ 68 60B L08C BA-S 60B 603B/66 Y9 60B 60B 60 60B AZ L08C BA-S 60B 603B/66 Y9 60B RIGHT SIDE Y8 Y8 67 Outside View DIAGRAM SHOWS THE ASSEMBLED 8X4 GRANDIO ASCENT THE BOX CONFIGURATION IS AN ASCENT 8X8 PLUS () 8 FOOT EXTENSION KITS 69 BA-S 8x8 Ascent Side (8 Extension Side) 8X Ascent Side (8 Extension Side) 8X Ascent Side 0

12 BASE KIT ASSEMBLY INSTRUCTIONS Pre-Plan The Placement Of Your Structure Allow enough room to get a wheel barrow in and around your structure. Be sure the orientation will allow for proper drainage in and around your greenhouse. It is recommended that you place your greenhouse in an area of your property that receives the most sunlight but is also somewhat protected by trees, fencing or your home for wind protection and also to keep the temperature up during early spring and late fall. The best placement depends on the features of your property, it is suggested in most scenarios to have your greenhouse face South on its broadest side and to have the door face East or West depending on typical wind directions in your area. Do not worry if your orientation will not allow for the placement to be as suggested, as a greenhouse that is facing North is better than no greenhouse at all. Avoid building your greenhouse at the base of a slope as these are often frost pockets where cold air collects, this will not be good for your greenhouse in keeping the temperature up inside. Extreme Wind Conditions: If you live in a windy location there is no way to build a 00% storm safe greenhouse, but there are a number of things you can do to minimize the chance of damage. Ensure that the base is level and square, be sure all panels are tightly in place and that all aluminum extrusions are tight. The main problem is usually that wind gets into the greenhouse and the pressure pushes a panel out and then the force of the wind on the interior causes more damage. It is best if you are expecting an extreme weather event that you disable any auto roof vents and make sure all doors and windows are closed and locked shut. Also you may need to build a wind break for extreme condition areas where wind is constant and extreme. It is ideal for your greenhouse to have water, electricity and even gas plumbed into place before construction. This will make watering plants and keeping the temperature and air circulation to the max efficiency. See pages 9 and 0 for installation methods below For Cement Base Installation: We suggest you use wedge style concrete anchoring bolts to secure your structure. For Deck Base Installation: We recommend you use a set of anchoring bolts to secure your structure. For Earth Installation: We recommend you use the anchoring system provided and bury corner posts into the ground and seal into place with quickrete.

13 BASE KIT PARTS LIST (GRA-BA-8) BASE AND ACCESSORY PACKING LIST PARTS WILL BE FOUND IN (GRA-BAS-8) BOX GRAPHIC PART NAME SIZE/LOCATION QUANTITY (GRA-BA-4X) BASE AND ACCESSORY PACKING LIST PARTS WILL BE FOUND IN (GRA-ASC-4X) BOX GRAPHIC PART NAME SIZE/LOCATION QUANTITY BA-S 97 3/8 in / 474 mm BA-S5 46 3/4 in / 87 mm BA-S 94/4 in / 394 mm BA-S6 46 3/4 in / 87 mm BA-C3 BA-A BA-S03 BA-M03 5 7/6 in 38 mm 9 3/6 in / 50 mm M6*4 NUT BA-C4 BA-A BA-S0 BA-S03 8 7/6 in / 4 mm 9 3 /6 in / 50 mm / x 3/4 M6*4 6 PARTS LIST FOR BASE KIT W05 CLIPS 9 BA-M03 NUT 6

14 (GRA-BA-8X) BASE AND ACCESSORY PACKING LIST PARTS WILL BE FOUND IN (GRA-ASC-8XA) BOX GRAPHIC PART NAME SIZE/LOCATION QUANTITY BASE KIT PARTS LIST BA-S3 93 7/6 in / 374 mm BA-S4 93 7/6 in / 374 mm PARTS LIST FOR BASE KIT BA-C4 BA-A BA-S0 BA-S03 BA-M03 8 7/6 in /4 mm 9 3/6 in / 50 mm / X 3/4 M6*4 NUT 6 6 3

15 8x BASE KIT ASSEMBLY INSTRUCTIONS (GRA-BA-8) AND (GRA-BA-4X). Layout all base kit pieces to prepare for assembly. Note that one BA-S will be at the front and one BA-S will be at the back and the BA-S s will be on the sides attaching to the front BA-S. The BA-S5 and BA-S6 will attach to the back BA-S, See diagram.. Attach the BA-S to the BA-S5 with the BA-C4 using the BA-S03 and BA-M03. See. Repeat for other side connecting the BA-S6 and the BA-S. Go to page 8 for the next step. BA-S5 BA-C4 BA-S BA-S03 BA-M03 BA-C3 BA-S BA-C3 BA-A BA-S5 BA-S6 BA-S0 BA-C4 44 BA-A BA-A BA-S BA-A BA-S0 BA-C4 BA-S BA-S BA-C3 GRANDIO Note that the holes for TIP screws on the base kit sides have about a foot gap between each, so be sure base kit extensions are assembled properly. See. BA-C3 4 BA-A BA-A 97.5 STEP ONE

16 8x6 BASE KIT ASSEMBLY INSTRUCTIONS (GRA-BA-8) AND (GRA-BA-8X).3 Layout all base kit pieces to prepare for assembly. Note that one BA-S will be at the front and one BA-S will be at the back and the BA-S s will be on the sides attaching to the front BA-S. The BA-S3 and BA-S4 will attach to the back BA-S See diagram..4 Attach the BA-S to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03. See. Repeat for other side connecting the BA-S4 and the BA-S. Go to page 8 for the next step. BA-S3 BA-C4 BA-S BA-S03 BA-M03 BA-C3 BA-C3 BA-S BA-A BA-S3 BA-S4 BA-S0 BA-C4 9.5 BA-A BA-A BA-S STEP ONE GRANDIO Note that the holes for TIP screws on the base kit sides have about a foot gap between each, so be sure base kit extensions are assembled properly. See. BA-A BA-S0 BA-C4 BA-S BA-C3 BA-S BA-A BA-C3 BA-A

17 8x0 BASE KIT ASSEMBLY INSTRUCTIONS (GRA-BA-8) AND (GRA-BA-8X) AND (GRA-BA-4X).5 Layout all base kit pieces to prepare for assembly. Note that one BA-S will be at the front and one BA-S will be at the back and the BA-S s will be on the sides attaching to the front BA-S. The BA-S5 and BA-S6 will attach to the back BA-S, See diagram..6 Attach the BA-S to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03. See. Repeat for other side connecting the BA-S4 and the BA-S, then BA-S3 to BA-S5 and BA-S4 to BA-S6. Go to page 8 for the next step. BA-S5 BA-C4 BA-S BA-S03 BA-M03 BA-C3 BA-SB BA-C3 BA-S6 BA-S5 BA-A BA-S0 BA-C4 BA-A BA-S BA-A BA-S0 BA-C4 BA-A BA-S4 BA-S0 BA-C4 BA-A BA-S GRANDIO Note that the holes for TIP screws on the base kit sides have about a foot gap between each, so be sure base kit extensions are assembled properly. See. BA-A 6 BA-S0 BA-C4 BA-S BA-C3 BA-SF BA-C3 BA-A 97.5 STEP ONE

18 8x4 BASE KIT ASSEMBLY INSTRUCTIONS (GRA-BA-8) AND (GRA-BA-8X) AND (GRA-BA-8X).7 Layout all base kit pieces to prepare for assembly. Note that one BA-S will be at the front and BA-S will be at the back and the BA-S s will be on the sides attaching to the front BA-S. The BA-S3 and BA-S4 will attach to the back BA-S. The BA-S3 will attach to the other BA-S3 and BA-S4 will attach to the other BA-S4 See diagram..8 Attach the BA-S to the BA-S3 with the BA-C4 using the BA-S03 and BA-M03. See. Repeat for other side connecting the BA-S4 and the BA-S, and then the BA-S3 to the BA-S3, and then the BA-S4 to the BA-S4. Go to page 8 for the next step. BA-S3 BA-C4 BA-S BA-S03 BA-M03 BA-C3 BA-SB BA-C3 BA-A BA-S3 BA-S4 BA-S0 86 BA-A BA-A BA-S3 BA-A BA-S0 BA-C4 BA-S4 BA-S0 BA-C4 BA-A BA-S STEP ONE GRANDIO Note that the holes for TIP screws on the base kit sides have about a foot gap between each, so be sure base kit extensions are assembled properly. See. BA-A BA-S0 BA-C4 BA-S BA-SF BA-C3 BA-C BA-A

19 BASE KIT ASSEMBLY INSTRUCTIONS.9 Slide the BA-C3 into the BA-S, slide the BA-S into the BA-C3, align the holes and push together to an even and tight position and use the BA-S03 Bolt and BA-M03 Collard Nut combo, tighten the collard nut on the inside of the base kit using the 0mm wrench. Repeat this process on all corners. See and. Note: BA-S will be the front and back, while the BA-S s will be the sides of your greenhouse base..0 For Ground Installation only Insert the BA-S03 and the BA-A into the holes at the bottom side of the base, the nut will be tightened on the inside of base. If you are mounting your base kit to a flat mount surface like a deck or cement pad discard the BA-S0 and BA-A, you will need to purchase an fastener for your installation surface. BA-S03 BA-S BA-S BA-S FRONT BA-S03 BA-C3 SIDE BA-S03 BA-M03 Collared Nut BA-S BA-S03 ML0 BA-M03 Collared Nut BA-C3 BA-A BA-A STEP ONE 8

20 BASE KIT GROUND INSTALLATION **BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY. BA-A must be buried in ground. See. Dig holes to bury the BA-A s, you determine size and depth for your location. We recommend you use: Quikrete fast setting concrete to anchor base. Follow the directions on the package. Outdoor Ground Assembly BA-S BA-S STEP ONE GRANDIO Make sure base is squared TIP and level before setting anchor into concrete. Use a measuring tape to ensure all corners are the same. Use level on all four sides. BA-S03 BA-A BA-A * Must be inserted into the ground, and secured with concrete. 9

21 BASE KIT DECK INSTALLATION **BASE MUST BE LEVEL & SQUARE, FOUNDATION MUST BE PROPERLY ANCHORED PRIOR TO GREENHOUSE ASSEMBLY. Holes are present in base kit for anchoring bolts see and. You determine and acquire proper fastener prior to installation for your surface. Discard the BA-A and BA-S0 for deck installations. BA-S BA-S Use lag bolt or concrete anchors to attach base. (Fasteners not included). Deck or Patio Assembly BA-C3 HOLE FOR ANCHOR BOLT OR SCREW. BA-S6 BA-S B BA-C4 BA-S03 BA-M03 Use an appropriate fastener to attach to your surface through these access holes. If surface is uneven you may want to purchase large washers that will fit under the base and allow fasteners to go through to use as a shim for leveling the base kit. GRANDIO Make sure base is squared TIP and level before setting anchors. Use a measuring tape to ensure all corners are the same. Use level on all four sides. STEP ONE 0

22 This picture shows the inside view of front section fully assembled. All parts for this section will be found in boxes GRA-ASC-8A and GRA-ASC-8P. We recommend that you assebmle the fron wall on a tarp. W0 603C FRONT FRAME ASSEMBLY ALWAYS ASSEMBLE FRONT HORIZONTAL STEP TWO W0 60B W0T Y3- Y3- W04 603A 60B W0T Y- Y- L08D / 603B L08D / 603B Y Y 604-R 604-L L08A-X L08A-X 60A-FR 60A-FL W0 GRANDIO We recommend watching TIP our how to assembly videos with tricks and tips for easier assebly and installation of your Grandio Greenhouse at: GRANDIO Lay flat on ground to TIP assemble the front frame of your greenhouse. If possible try to find a shady area protected from the wind. Panels can burn grass and plants if in direct light. GRANDIO BOLT INSTALLATION TIP: TIP Locate all nuts and bolts, pre thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement. Inside View 69

23 FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL. Use W0 bracket to attach the () 60B s together with the 603C, secure parts with the S05 fasteners provided as shown in. Pre thread W0 fasteners with S05 for ease of installation, only turn a few times. Screw heads will remain outside channel. S05 W0 S04 ML0 W04 603C. Insert Y3- and Y3- window panels as shown in. 60B 60B 603A.3 Attach 603C and 603A with W04 and S04/ML0 fasteners as shown in. S04/ML0 W0T.4 Attach W0T to 60B and 603A with the S04/ML0 fasteners as shown in, leave a bit loose to ease installation of next step. 603C Inside View 60B 603A IMPORTANT: POLYCARBONATE PANELS The UV-Protected side is covered with transparent film and must face toward the sun. The side covered in white film will always face the interior of the greenhouse. We suggest you peel all film off completely prior to assembly and use a permanent marker to place a small X on the lower right corner of each panel on the transparent side that faces the sun, each panel has a sticker labeling the panel number and this side always faces the sun or outward as well. DO NOT REMOVE LABELS UNTIL YOU INSTALL PANELS. The X is suggested in case you dis-assemble your greenhouse in the future so you may identify which side has the UV coating. Always use gloves when handling the polycarbonate panels as the edges can be very sharp. Polycarbonate Panels Transparent Film Opal White Film Sun IMPORTANT: Use only S05 Screws, other screws may damage frame. W0 Inside View W04 60B 603C 60B W0T W0T Y3- Y3-603A STEP TWO

24 FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL.5 View diagrams and attach the () 604 s and () 60A s to the 69 with the S04/ML0 nut and bolt combos. Note the orientation of the 60A-FR and 60A-FL and the holes that should be at the top of the piece and face to the front, see the diagram to the right. NOTE HOLES ON 60A SHOULD FACE FRONT OF GREENHOUSE 604-R 604-L INSIDE OUTSIDE shows where the corner pieces attach to 69. shows where the door frame attaches to the 69. OUTSIDE 60A-FR OUTSIDE 60A-FL INSIDE INSIDE 69 INSIDE OUTSIDE STEP TWO GRANDIO Make sure the hole on the TIP 60A-FL and 60A-FR face to the front of greenhouse for future install of the L and L8 bracket that holds the door header in place. GRANDIO BOLT INSTALLATION TIP: TIP Locate all nuts and bolts, pre thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement. TIP: If necessary you may use a screwdriver to wedge behind the bolt head. This prevents bolt from falling into the track. A ML0 S04 INSIDE 60A-FR 69 Inside View Inside View 604-R S04 69 ML0 INSIDE DOOR FRAME 3

25 FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL.8 Attach to 69, this will hold the polycarbonate panels in place. If it seems too tight slide fingers or nut driver along edges, gently stretching the to allow room for panels to fit. OUTSIDE Polycarbonate panel INSIDE S04/ML0.9 Insert Y polycarbonate panels into place, make sure Y s slide completely into as shown in. L08D.0 Set () 603B s atop the Y panels, then attach () L08D s to the 603B s, 60A s and 604 s using S04/ML0 fasteners, make sure it is snug with the tops of the Y panels, then tighten fasteners. See.. Insert the Y- and Y- polycarbonate panels into the track of the 603B. 603B Y- L08D 604-R 604-L Y- L08D 603B 60A-FR Y 60A-FL Y A 69 A L08D 60A-FR 603B S04/ ML0 L08D 603B 60A-FR 604-R Inside View GRANDIO TIP Transparent Film Outside Greenhouse Sun STEP TWO 604A-R Polycarbonate Panel Opal White Film Inside Greenhouse 4

26 FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL. Move roof and front section together and align the WG0 s into the 60A s, and align the S04/ML0 s on the W0T s into the 604 s. Insure a snug fit between the W0T s, 60B s and 60A s and then tighten the S05 screws as shown in. Tighten the W0T s with the S04 /ML0 nut and bolt as shown in..3 Attach the L08A-X s to 60A s and 604 s to square front section loosen S04/ML0 attached to the bottom of the () 604 s, square the frame with carpenter square or use a measuring tape to make sure corner measurements are the same, also check distance across from the top of 60A s, and also to the bottom of the 60A s across, make sure distance is the same. Tighten L08A-X s to hold squareness as shown in. 60B W0 60A-FR S05 60B 603C 60B 60A-FR S04/ML0 L08A-X Y3- Y3- W0T W0T 603A S05 STEP TWO 60B S04 603A W0T 604-R FAT END DOWN W0 L08D Y- Y- 60A-FR 604-R 604-L L08A-X L08D W0 L08A-X Y- Y- FAT END DOWN 60A-FL 60B W0 FAT END 5

27 FRONT FRAME ASSEMBLY CONTINUED ALWAYS ASSEMBLE FRONT HORIZONTAL.4 Attach the () L08A-X to 60A s and 604 s. See and..5 To square front section loosen S04/ML0 attached to the tops of the () L08A-X s, square the frame with carpenter square or use a measuring tape to make sure corner measurements are the same, tighten L08X s to hold squareness, L08A-X should be attached up from bottom bolt see. 60A-FR L08A-X 603C S04/ML0 60B W0T Y3- Y3-60B W0T 604-R 603A W0 Y- Y- W0 L08A-X 69 GRANDIO Set front aside in a shaded TIP area, do not lay on grass, prolonged sunlight through the polycarbonate panels will burn if placed directly on top of plants during the intense sun of the day. ML0 S04 60A-FR Y L08D 604-R L08A-X Use measuring tape to measure from corner to corner to assure square. 69 L08D 604-L L08A-X Y 60A-FL STEP TWO 6

28 BACK ASSEMBLY INSTRUCTIONS ALWAYS ASSEMBLE BACK HORIZONTAL This image shows the inside view of the back wall assembly. All parts for back assembly will be found in box GRA-ELI-8A and GRA-ELI-8P. We recommend that you assemble the back wall on a tarp. W0 GRANDIO TIP Transparent Film Outside Greenhouse Sun 60B 60B Polycarbonate Panel Opal White Film Inside Greenhouse W04- W04- Inside View STEP THREE GRANDIO Make sure the UV coated TIP side of the panel faces outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled. W0 L08B Y5- Y5- Y- Y- 603B 603B 603B 603B W0 GRANDIO BOLT INSTALLATION TIP: TIP Locate all nuts and bolts, pre thread and place in the groove of the extrusion to make installation easier. Move up or down for exact placement. 60A-B Y 60D L08B-X 60C Y4 Y4 60D L08B-X Y 60A-B L08A 7

29 3. Prethread all S05 Screws into the W0 and W0 s, only turn a few times, see. 3. Use W0 bracket to attach the () 60B s together as shown in diagram. BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL FAT END WG0 WG0 WG0 FAT END Attach () W0 s to the () 60B s as shown in diagram. W0 3.3 Attach () 60A-B s to L08A using S04/ML0 fastener as shown in diagram. 60B 60B Attach () 60D s to L08A using S04/ML0 fasteners as shown in diagram. W0 W0 Attach 60C to L08A using S04/ML0 fastener as shown in diagram. 60B S05 W0 60B 60B STEP THREE Inside View W0 FAT END DOWN 60A-B 60D 60C 60D 60A-B 60A-B 60D 60C L08A ML0 S04 INSIDE L08A L08A INSIDE L08A ML0 S04 8

30 BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL 3.4 Attach (4) s to L08A as shown in diagram. Insert the Y polycarbonate panels into the grooves of 60A-B s, 60D s and 60C. Make sure Y panels are inserted into as shown in. 3.5 Set (4) 603B s on top of the Y s that are now in place. Attach L08B to () 60A-B s, 60D s and the 60C with S04/ML0 fasteners as shown in diagram, and,. Pre thread all fasteners into assigned channels and align with L08B for ease of installation. 603B L08B Y- Y4- Y4-603B 603B Y- 603B STEP THREE 3.6 Insert the Y-, Y-, Y4- and Y4- polycarbonate panels into place as shown in the diagram to the right. 60A-B Y 60D L08A Y 60C Y Y 60D 60A-B Inside View Polycarbonate Panel L08A 60A-B ML0 S04 L08B L08B 603C 60C L08B 603B 60D 603B 603B L08B 60C 9

31 BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL 3.7 Attach the roof to the back wall use W0 fastener to 60C and the () W0 s to the () 60A-B s using the S05 fasteners as shown in diagram and, pre thread all screws for easiest installation, tighten when flush with frame and square. W0 60B S05 W0 60B 60C W0 60A-B Y- 603B Y4- L08B 603B 60C Y4-603B Y- 603B W0 60A-B Inside View 60B W0 FAT END DOWN STEP THREE Y Y 60D Y Y 60D 60A-B L08A 30

32 3.8 A. Attach the W04- to the 60D and 60B with S04/ML0 fasteners as shown in. B. Attach () L08B-X s to () 60D s and L08A with S04/ML0 as shown in. C. Attach () L08B-X s to the () 60A s with fasteners as shown in. BACK CONTINUED ALWAYS ASSEMBLE BACK HORIZONTAL S04/ML0 W04-60D 60B 60A-B S04/ML0 L08B-X Inside View 60D STEP THREE L08B-X L08A L08B-X L08B-X ML0 S04 60D 60D GRANDIO Square by loosening bolts TIP attached to the tops of the L08B-X, use measuring tape to make sure corners to corner measures the same. 3

33 MIDDLE ASSEMBLY INSTRUCTIONS Warning: The person(s) holding the front or back sections vertical must continue to do so until the angle supports are attached securely to the front and base as shown in step 4.5. Failure to hold front vertical will cause the front to fall and damage the base kit, front framing etc. Damage caused by improper installation is not warrantable. 4. We recommend pre threading all (9) W05 Clips with the nut and bolt combos now. See, note the bolt head will always slide into the extrusion, W05 clips will be used in step With no less than people place the pre assembled front section on top of the base kit front. Have person () hold the front vertically while the other attaches the front section 60A s to the base using S04/ML0 fasteners as shown in. Person () must continue to hold up the front wall! ML0/ NUT W05 CLIP S04 BOLT 60A ML0 S04 BA-S Inside View Front Right side BA-SF STEP FOUR BA-S BA-S5 BA-S6 **This Base shows a 8x, your greenhouse may be longer and configured of more base kit pieces. GRANDIO You will need a minimum of TIP () people to complete the middle assembly of your greenhouse. The more people the merrier at this stage of assembly. BA-S 3

34 MIDDLE ASSEMBLY CONTINUED 4.3 Attach to 60A and the BA-S with S04/ML0 on both sides as shown in and with the nut and bolt combos. 4.4 Attach the front section 69 to the base using S04/ML0 fasteners as shown in, then attach the threshold support to the inside of the 69 with (4) self tapping screws included in the package, see. 60B STEP FOUR 60A L08D L08A-X A Threshold Support will attach with 4 self tapping screws 60A 69 Attaches to the base kit with S04/ML0 BA-S Base 33

35 MIDDLE ASSEMBLY CONTINUED 4.5 Have one person hold the front vertically while the other attaches the font section to the base with W05/S04/ML0 fasteners as shown in, and. The (4) W05 clips will catch the under edge of the front base kit and then slide upward attaching to the bottom of the 60A s and the 604 s, you will switch out the combo that was originally used to the W05 Clip. 69 Base BA-S W05 Inside BA-S6 BA-S BA-S5 604 STEP FOUR BA-S 60A 604-R L08A-X 69 60A ML0 S04 BA-S BA-S 60A BA-S W05 ML0 S04 W05 Inside View 34

36 MIDDLE ASSEMBLY CONTINUED 4.6 Attach back wall 60A s with back base corners using S04/ML0 on both sides as shown in. 4.7 Attach bottom of to rear section of base kit with S04/ML0, as shown in. Attach the to the 60A as shown in, make sure the S04/ML0 combos are tight. 4.8 Use the (5) remaining W05 clips to attach the backwall where the 60A s meet the corner of the base as shown in, and where 60D s, and the 60C meet the BA-SB see. Then use W05 Clip combos to attach the corner 60A s to the base kit as shown in, you will have to switch out the combo that was originally used to the W05 Clip. 60B STEP FOUR 60A ML0 S04 BA-S or BA-S6 BA-S 60A L08B L08B-X Inside View Back Left side 60C 60D 60D W05 Inside Back Base 60C, 60D Outside Base Back Wall 60A ML0 S04 BA-S or BA-S6 BA-S Back Base Base W05 Inside View 35

37 4.9 Attach the 607 to 607 extension with the 607-XS and the (4) S08 screws provided see,. The S08 screws are to be installed on the inside as shown in diagram. Wait to tighten the screws all at one time when both sections are aligned correctly, apply even pressure while tightening. MIDDLE ASSEMBLY CONTINUED 607-XS Apply a bead of silicone to the seam where the 607 s meet and to the holes where the S06 screws will attach the DP0 to the 607 ridge. See. Immediately attach DP0 and insert the S06 screws once the silicone is applied. For 8x0 and 8x4 Grandio Ascent Assembly DP XS S STEP FOUR Repeat these steps if you are building an 8x0 or 8x4 with your last extension box, note it is best to connect 8x8, then 8X, then an 4X if assembling an 8x0. Note that the notches shown in should be spaced every feet, none should be right next to each other. 607 FRONT WARNING 607 S06 S06 Notches Notches FRONT 607 DP0 APPLY SILICONE CAULK TO RIDGE AND HOLES 36

38 MIDDLE ASSEMBLY CONTINUED 4.0 With people, attach the ridge to front and back by sliding into place as shown in and, using S04/ML0 fasteners attach the 607 to the 60B s. See for how the final orientation should be. Side Angle View 607 STEP FOUR 607 Inside View B 60B Inside View S04/ML B 60B 37

39 EXTENSION ASSEMBLY INSTRUCTIONS Warning: You will need a minimum of people to complete this section, you will not be able to stop assembly until page 44. Note that if you are assembling an 8x0 or an 8x4 greenhouse you will proceed thru the nd extension assembly instructions. Damage caused by improper installation is not warrantable. It will be helpful to prepare and lay each section and necessary parts out prior to beginning this sections actual assembly, pre reading will make this section much easier. STEP FIVE Warning: This section will take about 30 minutes so be prepared to finish there is not a stopping point until page 44 for an 8x or 8x6 or page 50 for an 8x0 or 8x4 depending on your greenhouse configuration. Note it may be helpful to have a few more people at this point the more the merrier. GRANDIO BOLT INSTALLATION TIP: TIP Locate about 30 nuts and bolts and pre thread for easiest installation. 38

40 STEP FIVE EXTENSION ASSEMBLY INSTRUCTIONS 5. Connect the () braces labeled L08M-X / together with the nut and bolt combo S04/ML0 see. The combined L08M-X s should measure about 94 / when connected together. 5. Attach the to the base with a nut and bolt combo where the extension kit meets on the base kit, with other person holding the in place. Measure down 6 from the top of the to attach the W4 bracket to the on both sides with the S04/ML0. See and. Attach the assembled L08M-X s to the W4 as shown in and. L08M-X L08M-X This part is labeled with stickers and L08M-X. We will refer to this part as L08M-X in all instances moving forward until we use this as an support on page Have one person keep holding the and L08M-X on one side for support while you prepare for next step on the next page. W4 BRACKET 6 Measure W4 Back Measure 6 L08M-X L08M-X W4 BA-S Back Front BASE IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN 39

41 EXTENSION ASSEMBLY INSTRUCTIONS 5.4 Attach the to the () -X s with (4) of the S09 screws provided see and. The S09 screws are to be installed on the outside of the and will tighten into the -X as shown in the diagrams. Repeat with other set, note they will be opposite of each other when assembled. Pay special attention to the orientation of the, make sure the correct side faces down, see. -XS UP S09 FRONT STEP FIVE Profile View OUTSIDE VIEW INSIDE VIEW Groove UP -XS UP FRONT 40

42 EXTENSION ASSEMBLY INSTRUCTIONS STEP FIVE 5.5 With people proceed to install in this order, note that must be installed with groove side down see.. With one person holding the level and in position have the other person loosen the top of the and let it fall free, attach the to the 60B using S04/ML0 (nut and bolt). See and.. Now move the loosened S04/ML0 (nut and bolt) currently attached to the upward to secure the, 60A-F and together as shown in. 3. Have assistant keep holding at the middle section. Turn to next page for detailed installation. Groove 60A Profile View 60B Note the line on the that shows the exact placement of the 60B s and the 60A s when installed correctly. UP 60B LOOSEN ML0 Inside View 60B 60A L08D 60B 60B Inside View 60A 607 S04/ML0 L08D 60B 60A GRANDIO You will need a minimum of TIP () people to complete the middle assembly of your greenhouse. The more people the merrier at this stage of assembly. 60A 4

43 EXTENSION ASSEMBLY INSTRUCTIONS 4. Note the top of should touch the line on the for exact placement, see. Attach the to the with the S04/ML0 nut and bolt combos see diagram. 5. Repeat steps -4 on the other side see. STEP FIVE NOTE EXACT PLACEMENT OF THE TO THE. 60B 607 EXACT PLACEMENT LINE FOR OUTSIDE VIEW FRONT 60B 60A -XS S04/ML0 INSIDE VIEW FRONT 60A 4

44 EXTENSION ASSEMBLY INSTRUCTIONS 5.6 With person holding the steady person will attach the 60B s between the and 607 on both sides. See and. STEP FIVE Inside View 60B 60B 607 ML0/S04 Outside View B EXACT PLACEMENT 43

45 EXTENSION ASSEMBLY INSTRUCTIONS 5.7 Connect the AZ- with the included hardware, see. With two people attach the AZ- to the base and the lower, see. Then attach the upper end to the mid roof line see. Install on both sides of the greenhouse where the extension seams meet using the S0/ML0 combo. 5.8 Install the BZ- to the upper mid roof, to act as the support to the peak of the roof as shown between the () 60B s with S04/ML0 nut and bolt combos, see. ML0 AZ- AZ- Bracket S0 STEP FIVE AFTER COMPLETING STEP 5.9 IF YOUR GREENHOUSE IS AN 8X OR 8X6 SKIP TO PAGE 5. IF YOURS IS AN 8X0 OR 8X4 PROCEED ON TO THE NEXT PAGE. BZ- 607 AZ- INSIDE VIEW AZ- S0/ML0 You will need to switch this bolt out to an S0 AZ- S0/ML0 AZ- BRACE (longer edge touches bottom of interior base kit) 44

46 nd EXTENSION ASSEMBLY INSTRUCTIONS CONTINUE FOR 8X0 AND 8X4 ONLY / FOR 8X AND 8X6 SKIP AHEAD TO PAGE 50 OR STEP 5.7 STEP FIVE 5.9 Connect the () braces labeled L08M-X / together with the nut and bolt combo S04/ML0 see. The combined L08M-X s should measure about 94 / when connected together. 5.0 Attach the to the base with a nut and bolt combo Measure down 6 from the top of the to attach the W4 bracket to the on both sides with the S04/ML0. See and. Attach the assembled L08M-X s to the W4 as shown in and. 5. Have one person keep holding the and L08M-X on one side for support while you prepare for next step on the next page. W4 BRACKET L08M-X 6 L08M-X This part is labeled with stickers and L08M-X INSIDE VIEW Measure 6 L08M-X W4 L08D-X L08M-X W4 Measure 6 IMPORTANT TO HAVE THE L08M-X FACE THE BACK AS SHOWN Back Front BASE 45

47 nd EXTENSION ASSEMBLY INSTRUCTIONS CONTINUE FOR 8X0 AND 8X4 ONLY / FOR 8X AND 8X6 SKIP AHEAD TO PAGE 50 OR STEP Attach the to the () -X s with (4) of the S09 screws provided see and. The S09 screws are to be installed on the outside of the and will tighten into the -X as shown in the diagrams. Repeat with other set, note they will be opposite of each other when assembled. -XS STEP FIVE Pay special attention to the orientation of the, make sure the correct side faces down, see. S09 FRONT Profile View OUTSIDE VIEW INSIDE VIEW Groove -XS FRONT 46

48 nd EXTENSION ASSEMBLY INSTRUCTIONS CONTINUE FOR 8X0 AND 8X4 ONLY / FOR 8X AND 8X6 SKIP AHEAD TO PAGE 50 OR STEP 5.7 STEP FIVE 5.3 With people proceed to install extension at the eave.. With one person holding the level and in position have the other person attach the to other end of the -XS as shown in.. With one person holding the level and in position have the other person attach the to the using S04/ML0. See. 3. Repeat steps. and. on other side of the greenhouse. OUTSIDE VIEW NOTE EXACT PLACEMENT OF THE TO THE. EXACT PLACEMENT LINE FOR FRONT S09 -XS FRONT Profile View GRANDIO You will need a minimum of TIP () people to complete the middle assembly of your greenhouse. The more people the merrier at this stage of assembly. Groove 47

49 nd EXTENSION ASSEMBLY INSTRUCTIONS CONTINUE FOR 8X0 AND 8X4 ONLY / FOR 8X AND 8X6 SKIP AHEAD TO PAGE 50 OR STEP Attach the () 60B s between the and 607 on both sides. See and. STEP FIVE Inside View 60B B ML0/S04 Outside View B EXACT PLACEMENT 48

50 nd EXTENSION ASSEMBLY INSTRUCTIONS CONTINUE FOR 8X0 AND 8X4 ONLY / FOR 8X AND 8X6 SKIP AHEAD TO PAGE 50 OR STEP 5.7 STEP FIVE 5.5 Connect the AZ- with the included hardware, see. With two people attach the AZ- to the base and the lower, see. Then attach the upper end to the mid roof line see. Install on both sides of the greenhouse where the extension seams meet using the S0/ML0 combo. 5.6 Install the BZ- to the upper mid roof, to act as the support to the peak of the roof as shown between the () 60B s with S04/ML0 nut and bolt combos, see. ML0 AZ- AZ- Bracket S0 INSIDE VIEW AZ- S0/ML0 You will need to switch this bolt out to an S0 60B B BZ- AZ- AZ- FRONT S0/ML0 AZ- BRACE (longer edge touches bottom of interior base kit) 49

51 MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 5.7 With two people attach the extension to -XS with the (4) S09 screws provided see and. Inside View 60B 5.8 With person still holding in place have person loosen the nut and bolt combo to attach the into place, see. Repeat these steps on other side of the greenhouse, and then mid roof line see. S04/ML0 L08B STEP FIVE -XS 60B A -XS FRONT ML0/S04 INSIDE VIEW OUTSIDE VIEW 60A-B -XS S09 FRONT 50

52 STEP FIVE MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 5.9 Before you attach the s to the sides of the greenhouse you will need to loosen the ML0 (nut) attached to the and the base. See diagram. Remove and set aside the L08D-X supports.. Once the bottom of one is loosened set the onto the bolt of the. Be sure the is aligned and sitting flush on top of the base kit. See for reference. Inside View ML0/S04 BA-S ML0/S04 Inside View BASE S04 ML0 Inside View Loosen only one at a time.. Hold the in place and attach the top of the to the using S04/ML0 (nut and bolt). As shown in Repeat steps. and. on all four corners where the s meet the base kit. 4. Now attach the bottom of to the Base using a S04/ML0 (nut and bolt) as shown in, and to the with an S04/ML0 combo as is shown in. L08D-X 5. Repeat step 4. on all places where a should go. You may reference diagrams at front for your exact size. Note: Where the reattaches to the BASE and the be sure to secure them tightly see. 5

53 MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 5.0 Assemble the roof window vents as shown below in and, using the Z0 screws attach the 65, 66, and 68 s with the Y8 panel as shown, be careful not to strip the screw heads. Pay attention to the Y8 panel, stickers face the sun, and that the frames are assembled according to images below. 5. Insert assembled window into the end of ridge of 607 and slide into position. See. Window positions are your discretion however, must be in the middle for support, do not place nearest the front or back as you will need a 60B support to keep in window vent in place. Place directly across from each other for best cross draft ventilation, see for optional placement. Attach the 60B s as shown between and, after all roof vents are positioned. 60B 60B Y8 60B B 60B Y8 Y8 STEP FIVE 66 Z0 68 SUN Z PC sheet Note Correct Orientation Z0 SUN Screwdriver Z0 Outside View GRANDIO TIP attaching all 60B s. Place roof windows in desired location before 66 Z0 Y8 68 Z0 5

54 STEP FIVE MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 5. Install plastic strip before inserting 4.6 polycarbonate Install plastic sheet strip s, 606 see before inserting. You will attach the polycarbonate -CAP s to sheet the top s. of each prior to installation see. Install all panels into the channel s of the side walls, and 4.7 fit down After into s the are. installed, loosen bolts attached to in all upper corners. Using a level, adjust 5.3 and After tighten s are bolts. installed, Repeat loosen in every bolts corner attached to until the greenhouse in all upper is corners. level. The Using top a edges level, of adjust s and will tighten align when bolts. Repeat greenhouse in every is level. corner until the greenhouse is plumb. The top edges of s will align when greenhouse is level or plumb. See. Y9 Y9 Y9 Loosen L08C S04/ML0 -CAP PC sheet -Panel OUTSIDE OUTSIDE L08C GRANDIO Make sure the UV coated TIP side of the panel faces outward as indicated on the panels. Avoid placing the polycarbonate panels in the sun or near plants until fully assembled. 53

55 MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 5.4 To ensure there is no gap in roof vent position 603B as shown in. Connect 603B to middle of 60B s using W04 bracket as shown in. 5.5 Attach HQC0 to 66 with the Z04 screws see, close roof vent and attach the handle onto HQC0 middle pin (the first two holes of the handle to the second and third pins of HQC0). Then attach HQC0 into 603C s track with S04/ML0 (nuts and bolts), see. HQC0 60B Inside view of 603C 603B W04 Y Y8 Y8 603B 603C 68 STEP FIVE Note: If you are installing automatic roof vent openers follow those directions for correct installation. SAVE MANUAL OPENERS FOR WINTER SWITCHOUT. Y8 HQC0 Handle Y8 HQC0 Handle HQC0 Handle Z04 HQC0 Handle B ML0/S04 HQC0 54

56 MIDDLE ASSEMBLY INSTRUCTIONS CONTINUED 5.6 Attach -WS to the inner roof line of the 607 and on both top and bottom of as shown in and. STEP FIVE 5.7 Remove the L08M-X support combo, take apart and use as now and install on the sides of the AZ extension brace, as shown in. Note that the and L08M-X have been labeled with both stickers in this instance as this part has uses. Save the hardware and W4 bracket for possible future use or hang inside as a plant hanger clip. L08M-X PC Sheet Y8 Y8 Outside -WS 607 Outside Y8 -WS inside PC Sheet Inside -WS PC Sheet AZ GRANDIO Note that there are two TIP parts labeled & -WS, one is the gutter support, the other is a clip that fits under polycarbonate panels inside greenhouse. 55