OPERATION MANUAL 21 INCH WOODWORKING BAND SAW FOR YOUR SAFETY

Transcription

1 OPERATION MANUAL INCH WOODWORKING BAND SAW FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY

2

3 TABLE OF CONTENTS: Section Page General Specification/Wiring Diagrams... Operation Warnings... Safety Instructions for Operation...3 Parts list Band Saw (Front)... Parts list Band Saw (Rear)...5 Operating Instructions...6 Moving...6 Assemble The Machine...6 Adjusting 90 degree Table Stop...6 Rip Fence...6 Blades change...7 Adjusting Upper Blade Guide Assembly...7 Adjusting the Speed of Saw Blade...8 Adjusting the Tension of the Blade...8 Dust Collection...8 Setting the cutting height...8 Miter Gauge Adjustment...9 Parts List (Model No. SBW-5300 A) Diagram Parts List (Model No. SBW-5300 CE) GENERAL INFORMATION: The 7"(30mm) band saw is a well designed industrial machine that provide variety of wood working functions to meet your higher needs of a Band Saw. Followings are the basic functions you will find in this machine:. Quick Changed Saw Blade system given you an easy way to replace saw blade to cut different quality wood materials.. Adjustable Rip Fence can assist you to cut desired shapes. 3. Accurate Miter Gauge can let you create any curves you desire.. Effective Ball Bearing Guide System will let the band saw blade run more smoother. 5. Humanized Dust Chutes collect extra wood-chips, and give you a better working environment. 6. Extended " Height Space provides you a bigger working space to cut wider and higher wood selections.

4 . General Specifications Horse Power Apperance Cutting Height Max. Cutting Width Max. Cutting (Rip Fence) Saw Blade (L) Saw Blade (W) CE Saw Blade Speed, Saw Blade Speed Table Size Table Tilting Wheel Size Table Height From Ground Dust Chute Diameter N.W/G.W. Packing Size (LxWxH) CTN QTY / 0" / 0" HP 0" x 3" x 80" "(300mm) 0-/"(5mm) 8-5/8"(7mm) 3930mm /8" to -/" (Standard ") (890, 3800SFPM) " x "(530x530mm) O O Left-0 / Right-5 "(530mm) 37.5"(950mm) D" x 63 / 96kgs 37" x 0" x 87"(38CUFT) SETS / 50SETS WIRING DIAGRAMS:

5 . WARNINGS - Misuse of this machine can cause serious injury. - For safety, machine must be set up, used and serviced properly. - Read, understand and follow instructions in the operator's and parts manual which was shipped with your machine. When setting up machine: - Always avoid using machine is damp or poorly lighted work areas. - Always be sure machine is securely anchored to the floor. - Always keep machine guards in place. - Always put start switch in "OFF" position before plugging in machine. When using Machine: - Never operate with machine guards missing. - Always wear safety glasses with side shields (See ANSI Z87.) - Never wear loose clothing or jewelry. - Never overreach - you may slip and fall into the machine. Machinery general safety warnings. Always wear protective eye wear when operating machinery. Eye wear shall be impact resistant, protective safety glasses with side shields which comply with ANSI Z87. specifications. Use of eye wear which does not comply with ANSI Z87. specifications could result in severe injury from breakage of eye protection.. Wear proper apparel. No loose clothing or jewelry which can get caught in moving parts. Rubber soled footwear is recommended for best footing. 3.Do not overreach. Failure to maintain proper working position can cause you to fall into the machine or cause your clothing to get caught-pulling you into the machine..keep guards in place and in proper working order. Do not operate the machine with guards removed. 5. Avoid dangerous working environments. Do not use stationary machine tools in wet or damp locations. Keep work areas clean and well lit. Special electrics should be used when working on flammable materials. 6. Avoid accidental starts by being sure the start switch is "OFF" before plugging in the machine. 7. Neve leave the machine running while unattended. Machine shall be shut off whenever it is not in operation. 8.Disconnect electrical power before servicing. Whenever changing accessories or general maintenance is done on the machine, electrical power to the machine must be disconnected before work is done. - Never leave machine running while you are away from it. - Always shut off the machine when not in use. When servicing machine: - Always unplug machine from electrical power while servicing. - Always follow instructions in operators and parts manual when changing accessory tools or parts. -Never modify the machine without consulting Wilton Corporation. You- the stationary power tool user - hold the key to safety. Read and follow these simple rules for best results and full benefits from your machine. Used properly, Wilson's machine is among the best in design and safety. However, any machine used improperly can be rendered inefficient and unsafe. It is absolutely mandatory that those who use our products be properly trained in how to use them correctly. The should read and understand the Operators and Parts Manual as ell as all labels affixed to the machine. Failure in following o f these warnings can cause serious injuries. 9. Maintain all machine tools with care. Follow all maintenance instructions for lubricating and the changing of accessories. No attempt shall be made to modify or have makeshift repairs done to the machine. This not only voids the warranty but also renders the machine unsafe. 0.Machinery must be anchored to the floor..secure work. Use clamps or a vise to hold work, when practical. It is safer than using your hands and it frees both hands to operate the machine..never brush away chips while the machine is in operation. 3.Keep work area clean. Cluttered areas invite accidents..remove adjusting keys and wrenches before turning machine on. 5.Use the right tool. Don't force a tool or attachment to do a job it was not designed for. 6.Use only recommended accessories and follow manufacturers instructions pertaining to them. 7.Keep hands in sight and clear of all moving parts and cutting surfaces. 8.All visitors should be kept at a safe distance from the work area. Make workshop completely safe by using padlocks, master switches, or by removing starter keys. 9.Know the tool you are using- its application limitations, and potential hazards.

6 Safe by using padlocks, master switches, or by removing starter keys. 9.Know the tool you are using - its application, limitations, and potential hazards. General Electrical Cautions This saw should be grounded in accordance with the National Electrical Code and local codes and ordinances. This work should be done by a qualified electrician. The saw should be grounded to protect the user from electrical shock. Caution : For circuits which are far away from the electrical service box, the wire size must be increased in order to deliver ample voltage to the motor. To minimize power losses and to prevent motor overheating and burnout, the use of wire sizes for branch circuits or electrical extension cords according to the following table is recommended. 3. SAFETY INSTRUCTIONS. Always wear leather gloves when handling saw blade. The operator shall not wear gloves when operating the machine.. All doors shall be closed, all panels replaced, and other safety guards in place prior to the machine being started or operated. 3. Be sure that the blades is not n contact with the workpiece when the motor is started. The motor shall be started and you should allow the saw to come up to full speed before bringing the saw blade into contact with the workpiece.. Keep hands away from the blade area. See Figure A. 5. Remove any cut off piece carefully while keeping your hands free of the blade area. 6. Saw must be stopped and electrical supply must be cut off before any blade replacement or adjustment of blade support mechanism is done, or before any attempt is made to change the drive belts or before any periodic service or maintenance is performed on the saw. 7. Remove loose performed on the unnecessary workpieces from area before starting machine. 8. Bring adjustable saw guides and guards as close as possible to the workpiece. 9. Always wear protective eye wear when operating, servicing, or adjusting machinery. Eyewear shall be impact resistant, protective safety glasses with side shields complying with ANSI Z787. specifications. Use of eye wear which does not comply with ANSI87. specifications could result in severe injury from breakage of eye protection. See Figure B. 0.Nonslip footwear and safety shoes are recommended. See Figure C..Wear ear protectors (plugs or muffs) during extended periods of operation. See Figure D..The workpiece, or part being sawed, must be securely clamped before the saw blade enters the workpiece. 3.Remove cut off pieces carefully, keeping hands away from saw blade..saw must be stopped and electrical supply cut off or machine unplugged before reaching into cutting area. 5.Avoid contact with coolant, especially guarding your eyes. 3

7 SAW NOMENCLATURE Throughout this document, we make reference to various systems and components on the saw. The two illustrations on these pages will provide you with an overall frame of reference for the location and position of the various components. Where detailed illustrations for various subsystems will be helpful, you will find these illustrations accompanying the specific teat for each subsystem and its components. FRONT SIDE OF BAND SAW UPPER WHEEL COVER UPPER DRIVE WHEEL HAND DRIVE BLADE TENSION WINDOW CE. VERSION NVR SWITCH BLADE TENSION ADJUSTMENT KNOB UPPER BALL BEARING GUIDE SYSTEM MITER SLOT CRIP FENCE TABLE " DUST PORT LOWER WHEEL COVER LOWER DRIVE WHEEL MOTOR PULLEY

8 REAR OF BAND SAW LEVER ROD (QUICK CHANGE SAW BLADE SYSTEM) POSITIVE KNOB LOCK KNOB MOTOR 5

9 5. OPERATING INSTRUCTION MOVING a. Use a 000kgs wrecker hang up the machine on parts A (Fig. ) to suitable space. A Handle Wheel (B) b. To ensure sufficient upright stability of the machine and safety, you need to bolt the machine to floor on M0 screw. ASSEMBLE THE MACHINE:. Attach the handle (A, Fig. ) to the hand wheel (B, Fig. ), lock the screw then connect to the machine. Fig. Fig. (A) Handle. To mount table, remove table insert and table pin from the table. Slide the table slot to the saw blade, slow moving to the center to table, make sure the table is located to the m8 hole ( hole) and attach the spring washer, (Fig. 3) then replace table insert and table pin. 3. Adjust the table until the saw blade in the center o f table insert, then locked with screw. Fig. 3 ADJUSTING 90 DEGREE TABLE STOP. Unplug power cord.. Loosen the lock knobs (A, Fig. ) and tilting table left until it rests against table stop bolt.(a, Fig. 5) A 3. Use a protractor placed on the table and against the blade,(a,fig.6) to see If he table is 90 degree to the table. Fig.. If it is not 90 degree, you can use micro-adjust knob, please lock the lockknob. RIP FENCE. Setting the fixed base(a,.fig.7) to the cast iron table with two hex head blot m6x0, two spring washer m6. A Fig. 5.Setting the square tube (B,Fig.7) to the table with hex socket bolt m6x6. 3. Setting the fence (A.Fig 7) to the fence body, place the fence assembly on the fixed base, slide the fence on its guides until it is the required distance from the blade..check the scale, make sure the distance between the edge of the miter slot and both the front and rear of the rip fence, adjust so both distances are equal. 5. Lock the fence by pushing the locking handle. Fig. 6 B Square table C 6 A Fixed Base Fig. 7

10 BLADES CHANGING. Unplug power cord. A. Remove the table insert and table pin. 3. Open upper & lower wheel cover.. Loosen the upper & lower blade guide system and bearing. 5. Loosen lever rod the knob (quick change saw blade system) on rear of band saw. (A, Fig. 8) 6. Remove the table to direct through slot in table. Attention : the direction of new saw blade must be: B Fig Guide new blade through table slot, place blade in upper and lower ball bearing guide system. (AA) (BB) 8. Replace blade in the middle of the upper and lower wheel, if the saw blade is not in the right position, you must relax the fixed handle and adjust the positive knob. (B, Fig. 8) Fig Replace the table insert and table pin. 0.Adjust the blade tension and blade tacking if the blade width is different. ADJUSTING UPPER BLADE GUIDE ASSEMBLY. Set the bearing of upper & lower blade guide to within approx. 0.5mm of the blade, make sure the bearing the back of the blade approx. 0.5mm. (Fig.0,) see follow instruction.(aa,bb) Fig. 0. Do not set the bearing too close, a the friction generates heat, which may have an adverse effect on the bearings and the saw blade as well. Fig. 7

11 ADJUSTING THE SPEED OF SAW BLADE. Loosen the two screw (A, B, Fig. ), change the belt to the belt to the required belt solt.. Until the saw blade speed to 850m/min or 30m/min (3300SFPM, 600SFPM) A B 3. Locked the two screw. ADJUSTING THE TENSION OF THE BLADE Blade tension is set by a spring loaded tension mechanism on the upper drive wheel. Check the level of the tension device before cutting. The tension for various blade widths as indicated on the window of upper wheel cover. Turn the blade tension hand wheel (A,Fig. 3) and see the saw tension instruction (A,Fig. ) indicated on the window of upper wheel cover. Fig. DUST COLLECTION The band saw is recommended to connected to dust collect, there are two " dust port (A, Fig. 5) to attach with " steel clamping. Fig. 3 A SETTING THE CUTTING HEIGHT The upper blade guide should always be set as closes practical against the work. To adjust, loosen the hand wheel (A, Fig. ) at the side of housing and see the blade guide to the required height then tighten after setting. A Fig. A Fig. 5 8

12 MITER GAUGE ADJUSTMENT. Plate the miter gauge in the table slot.. Loosen the clamp screw on the miter gauge. 3. Adjust to the desired angle of cutting on miter gauge.. Tighten the clamp screw (Fig. 6). Fig. 6 9

13 Parts List For Inch Band Saw Model No. SBW-5300 A KEY NO. 3 PARTS NO. DESCRIPTION SIZE Q'TY 9950 RING M MACHINE BODY 6 SS05000 SET BOLT M5x BUSHING 8 WF0630 M6x 3 9 IC35005 POWER CORD 0 NH06000 M POINTER STEP SCREW UPPER SHAFT PS SPRING PIN 5x UPPER WHEEL SHAFT HINGE UPPER WHEEL SHAFT BUSHING 3 8 BB6003 BALL BEARING 60LLU UPPER WHEEL " 0 RR70000 RETAINING RING R7 WF x 30 SR08900 X SAW BLADE 5"x3/"X0.5mm WS SR M6x TIRE LOWER WHEEL " IDLE PULLEY 9 NH63380 "- UNF 30 WS " 0

14 KEY NO. 3 PARTS NO. DESCRIPTION SIZE Q'TY IM3500 MOTOR CORD SPRING 33 PS03600 PIN 3X LOCATE BLOCK BEARING SWITCH HANDLE WHEEL ADJUSTING BOLT 39 SF05000 PAN HEAD BOLT W/FLANGE M5X0 8 0 WE STAR WASHER M5 SF05900 PAN HEAD BOLT W/FLANG M5X6 NH M SWITCH PLATE SR08900 x6 5 WF x UPPER WHEEL SLIDING BRACKET 7 SR06000 M6x50 8 BR0000 RIVET 3.x6 8 9 SR06000 M6x LIMPID PIECE UPPER WHEEL COVER 56 SHO60500 M6x5 57 WF0630 M6x BRUSH 59 SR M6x KNOB

15 KEY NO. 6 PARTS NO. DESCRIPTION SIZE Q'TY NL06000 NYLON M STRAIN RELIEF M HEIGHT POINTER 6 NH SH08800 HEX HEAD LOLT x KNOB SCREW KNOB SCREW LOCATE HANDLE M CAM LOCATE BLOCK KNOB LEVER ROD 73 NH900 M SHAFT 75 SJ08000 HEX SOCKET BOTTOM HEAD SCREW x0 76 WS WS M COVER 79 SS08000 SET SCREW x0 80 NH LOWER WHEEL SHAFT 8 Mh35005 MOTOR HP 83 SR00500 HEX HEAD BOLT M0x5 8 WS00000 M MOTOR BRACKET 86 SJ08000 HEX SOCKET BOTTOM HEAD HEAD SCREW x PLATE 88 SF05000 PAN HEAD BOLT W/FLANGE M5x LOCATE BLOCK 90 KS KEY 5x5x35

16 KEY NO. 9 PARTS NO. DESCRIPTION SIZE Q'TY SH0800 HEX HEAD BOLT x0(l.h) MOTOR PULLEY 93 LA0000 V-BELT A 9 SR06000 M6x LOWER WHEEL COVER 96 WF0630 M6x3 97 WF x30 98 SR00700 M0x35 99 NH0700 M SMALL GEAR KNOB SCREW TRUNNION SUPPORT BRACKET 03 WS00000 M0 3 0 WF035 M0x 3 05 SR06900 M6x6 06 Sr M6x ADJUST BLOCK 08 NH06000 M ADJUST BOLT M6 0 BB60000 BALL BEARING 6000ZZ SJ0000 HEX SOCKET BOTTOM HEAD SCREW M0x0 WF0880 x 8 3 WF0880 x 8 SP0900 PAN HEAD BOLT Mx GEAR PLATE 6 NL08300 NYLOW 7 SP0900 PAN HEAD BOLT Mx HANDLE 9 WF00808 Mx POINTER 3

17 KEY NO. PARTS NO. DESCRIPTION SIZE Q'TY 3505 TRUNNION PLATE WS SH08900 HEX HEAD BOLT x6 SC08600 CARRIAGE BOLT x80 5 AB9800 0" FENCE SET 9800 ADJUST BASE FIXED SHAFT 9800 FIXED LUMP SHAFT SPRING PIECE CONVEX BRACKET 9800 SPACE BUSHING 980 ADJUST SCREW 9803 HANDLE 980 GUARD PIECE 9805 GUARD PIECE 3506 PLUG 9806 FIXED BASE L SQUARE TUBE L= SUPPORT TUBE L=690 LM SCALE SF0000 PAN HEAD BOLT W/FLANGE Mx0 SH06000 HEX HEAD BOLT M6x0 SR06900 M6x6 NH06000 M6 ST03900 TAPPING SCREW 3.5x8 SF0900 PAN HEAD BOLT W/FLANGE Mx6 NH08300 SR0600 M6x55

18 KEY NO. PARTS NO. DESCRIPTION SIZE Q'TY WS M TABLE "x" TABLE INSERT TABLE PIN 9 SR06900 M6x LEFT COVER THUMB SCREW M6x LOWER BLADE GUIDE SUPPORT GUIDE RING LOWER ADJUST SHAFT RIGHT COVER 36 SR05000 M5x0 37 WF050 M5x PROTECT COVER (ASM) STEP SCREW SLIDING PLATE 3 RS50000 RETAINING RING S5 BB600 BALL BEARING 60ZZ UPPER BLADE GUIDE SUPPORT GUIDE RING THUMB SCREW M6x6 8 SC08700 CARRIAGE BOLT x85 9 SR06900 M6x ADJUST BAR UPPER SPACING SLEEVE 5 SR06000 M6x UPPER GUIDE SUPPORT BLOCK 5 SP0000 PAN HEAD BOLT Mx0 5

19 KEY NO. 55 PARTS NO. DESCRIPTION SIZE Q'TY NH00700 M RACK UPPER GUIDE TUBE HANDLE WHEEL 59 SR06000 M6x LOCATE BUSHING BUSHING 6 SJ08000 HEX SOCKET BOTTOM HEAD SCREW x0 63 WS GUIDE BRACKET WORM CYLINDER FIXED PLATE GEAR FIXED BOLT COVER 70 SR08900 x6 7 SN0900 COUNTER SUNK BOLT Mx8 3 7 SS06900 SET BOLT M6x6 73 AB980 MITER GAUGE ASS'Y 980 GUIDE BAR 980 GUIDE 9803 POINTER 980 NYLON WASHER 9805 HANDLE /" 9806 MITER GAUGE BODY 9807 SHAFT SN06900 COUNTER SUNK BOLT M6x6 SF05900 PAN HEAD BOLT W/FLANGE M5x BUSHING 75 SR06000 M6X0 76 SF05000 PAN HEAD BOLT W/FLANGE M5X0 6

20 7

21 8

22 Parts List For Inch Band Saw Model No. SBW-5300 CE KEY NO. PARTS NO. DESCRIPTION SIZE Q'TY 3000 SWITCH COVER NH00700 M STRAIN RELIEF M RING M MACHINE BODY 6 SS05000 SET BOLT M5X5 7 IC3500 SWITCH CORD 8 WF0630 M6x 3 9 IC3500 POWER CORD 0 NH06000 M POINTER STEP SCREW UPPER SHAFT PS SPRING PIN 5x UPPER WHEEL SHAFT HINGE UPPER WHEEL SHAFT BUSHING 3 8 BB6003 BALL BEARING 60LLU UPPER WHEEL " 0 RR70000 RETAINING RING R7 WF x 30 SR08900 X SAW BLADE 5"x3/"X0.5mm WS SR M6x TIRE LOWER WHEEL " IDLE PULLEY 9 NH63380 "- UNF 30 WS " 9

23 KEY NO. 3 PARTS NO. DESCRIPTION SIZE Q'TY IM3500 MOTOR CORD SPRING 33 PS03600 PIN 3X LOCATE BLOCK BUSHING CE SWITCH JD HANDLE WHEEL ADJUSTING BOLT 39 SF05000 PAN HEAD BOLT W/FLANGE M5X0 8 0 WE STAR WASHER M BUSHING NH M SWITCH PLATE SR08900 x6 5 WF x UPPER WHEEL SLIDING BRACKET 7 SR06000 M5x50 8 BR0000 RIVET 3.x6 8 9 SR06000 M6x LIMPID PIECE 5 SF00600 PAN HEAD BOLT W/FLANGE Mx DOOR LATCH SWITCH (ASM) 53 SF05000 PAN HEAD BOLT W/FLANGE M5x SWITCH BUSHING UPPER WHEEL COVER 56 SR M6x5 57 WF0630 M6x BRUSH 59 SR M6x KNOB 0

24 KEY NO. 6 PARTS NO. DESCRIPTION SIZE Q'TY NL06000 NYLON M STRAIN RELIEF M HEIGHT POINTER 6 NH SH08800 HEX HEAD LOLT x KNOB SCREW KNOB SCREW LOCATE HANDLE M CAM LOCATE BLOCK LEVER ROD KNOB 73 NH900 M SHAFT 75 SJ08000 HEX SOCKET BOTTOM HEAD SCREW x0 76 WS WS M COVER 79 SS08000 SET SCREW x0 80 NH LOWER WHEEL SHAFT 8 MH3500 MOTOR HP 83 SR00500 HEX HEAD BOLT M0x5 8 WS00000 M MOTOR BRACKET 86 SJ08000 HEX SOCKET BOTTOM HEAD SCREW x PLATE 88 SF05000 PAN HEAD BOLT W/FLANGE M5x LOCATE BLOCK 90 KS KEY 5x5x35

25 KEY NO. 9 PARTS NO. DESCRIPTION SIZE Q'TY SH0800 HEX HEAD BOLT x0(l.h) MOTOR PULLEY 93 LA0000 V-BELT A 9 SR06000 M6x LOWER WHEEL COVER 96 WF0630 M6x3 97 WF x30 98 SR00700 M0x35 99 NH0700 M SMALL GEAR KNOB SCREW TRUNNION SUPPORT BRACKET 03 WS00000 M0 3 0 WF035 M0x 3 05 SR06900 M6x6 06 SR M6x ADJUST BLOCK 08 NH06000 M ADJUST BOLT M6 0 BB60000 BALL BEARING 6000ZZ SJ0000 HEX SOCKET BOTTOM HEAD SCREW M0x0 WF0880 x 8 3 WF0880 x 8 SP0900 PAN HEAD BOLT Mx GEAR PLATE 6 NL08300 NYLON 7 SP0900 PAN HEAD BOLT Mx HANDLE 9 WF00808 Mx POINTER

26 KEY NO. PARTS NO. DESCRIPTION SIZE Q'TY 3505 TRUNNION PLATE WS SH08900 HEX HEAD BOLT x6 SC08600 CARRIAGE BOLT x80 5 Ab9800 0" FENCE SET 9800 ADJUST BASE FIXED SHAFT 9800 FIXED LUMP SHAFT SPRING PIECE CONVEX BRACKET 9800 SPACE BUSHING 980 ADJUST SCREW 9803 HANDLE 980 GUARD PIECE 9805 GUARD PIECE 9806 PLUG 9806 FIXED BASE L= SQUARE TUBE L= SQUARE TUBE L=690 LM SCALE SF0000 PAN HEAD BOLT W/FLANGE Mx0 SH06000 HEX HEAD BOLT M6x0 SR06900 M6x6 NH06000 M6 ST03900 TAPPING SCREW 3.5x8 SF0900 PAN HEAD BOLT W/FLANGE Mx6 NH08300 SR0600 M6x55 3

27 KEY NO. PARTS NO. DESCRIPTION SIZE Q'TY WS M TABLE "x" TABLE INSERT TABLE PIN 9 SR06900 M6x LEFT COVER THUMB SCREW M6x LOWER BLADE GUIDE SUPPORT GUIDE RING LOWER ADJUST SHAFT RIGHT COVER 36 SR05000 M5x0 37 WF050 M5x PROTECT COVER (ASM) STEP SCREW SLIDING PLATE 3 RS50000 RETAINING RING S5 BB600 BALL BEARING 60ZZ UPPER BLADE GUIDE SUPPORT GUIDE RING THUMB SCREW M6x6 8 SC08700 CARRIAGE BOLT x85 9 SR06900 M6x ADJUST BAR UPPER SPACING SLEEVE 5 SR06000 M6x UPPER GUIDE SUPPORT BLOCK 5 SP0000 PAN HEAD BOLT Mx0

28 KEY NO. 55 PARTS NO. DESCRIPTION SIZE Q'TY NH00700 M RACK UPPER GUIDE TUBE HANDLE WHEEL 59 SR06000 M6x LOCATE BUSHING BUSHING 6 SJ08000 HEX SOCKET BOTTOM HEAD SCREW x0 63 WS GUIDE BRACKET WORM CYLINDER FIXED PLATE GEAR FIXED BOLT COVER 70 SR08900 x6 7 SN0900 COUNTER SUNK BOLT Mx8 3 7 SS06900 SET BOLT M6x6 73 AB980 MITER GAUGE ASS'Y 980 GUIDE BAR 980 GUIDE 9803 POINTER 980 NYLON WASHER 9805 HANDLE /" 9806 MITER GAUGE BODY 9807 SHAFT SN06900 COUNTER SUNK BOLT M6x6 Sn05900 PAN HEAD BOLT W/FLANGE M5x BUSHING 75 Sr06000 M6x0 76 Sf05000 PAN HEAD BOLT W/FLANGE M5x0 5

29 6

30 KEY NO. PARTS NO. DESCRIPTION SIZE Q'TY 9806 Parts List For Inch Band Saw Model. No Rip Fence FIXED BASE ADJUST BASE FIXED SHGAFT SHAFT SPRING PIECE BRACKET T= SUPPORT TUBE INTERVAL SHEATH HANDLE ADJUST SCREW CONVEX SR0603 M6x FIXED LUMP 9807 SQUARE TUBE NH SF0900 PAN HEAD BOLT W/FLANGE Mx GUARD PIECE GUARD PIECE PLUGGED 0 ST03900 TAPPING SCREW 3.5x8 LM SCALE NH06000 M6 3 WS M6 SR06900 M6x6 5 SH06000 HEX HEAD BOLT M6x0 6 SF0000 PAN HEAD BOLT W/FLANGE Mx0 7

31 8

32