Parts Manual 2013-V. Band Sawing Machine

Transcription

1 Parts Manual 2013-V Serial No: to Band Sawing Machine

2 MACHINE SPECIFICATIONS MODEL VOLTAGE CYCLE PHASE SERIAL NO. For your information and future reference, insert pertinent data concerning your machine in the spaces provided above. This information is printed on a label or stamped on a plate attached to the machine frame. Always specify model and serial numbers on all parts orders and correspondence concerning your machine. This will help avoid unnecessary delays and inconvenience during processing. The specifications contained herein were in effect at the time this manual was approved for printing. The DoALL Company, whose policy is one of continuous product improvement, reserves the right to change specifications or design at any time without notice and without incurring obligations. How to read your serial number: For Sales, Parts and Service, call DoALL SAWING PRODUCTS 2375B TOUHY AVENUE ELK GROVE, ILLINOIS U.S.A. YOUR SERVICE REPRESENTATIVE:

3 Page 1 PARTS MANUAL INDEX 1/12 Fiche No. C-17 Model 2013-V Serial No to PAGE NO. DESCRIPTION FIRST SERIAL LAST SERIAL PAGES C-1-71 Final Assembly All 2-3 C-9-32 *Air Feed Assembly All 4-5 C *Auxiliary Post Support Assembly (Extra Work Height) All 6-7 C-7-23 *Band Filing and Polishing Assemblies All 8-9 C-8-30 *Band Lubricator Assembly (Accu-Lube/Unist) All C Bandwheel Assemblies All C-9-33 *Carrier and Cable Assembly (Air Feed) All C-9-34 *Chip Blower Assembly (And Related Items) All C-10-2 *Disc Cutter Assembly All C-1-71 Door Latches All 2-3 C Drive Assembly All C-6-32 Electrical Assembly All C-6-33 Electrical Control Box Assembly All C *Extra Work Height Assembly All C-3-46 *Glide Table Assembly All C *Guard Assembly (Point of Operation) All C Head Assembly All C-1-71 Job Selector All 2-3 C *Laser Line Generator Assembly All C-6-32 Limit Switches (Interlocks) All C-8-17 *Magnifier All C-8-16 *Mist Coolant Assembly (And Related Items) All C *Mitre Assembly (#2 Cut-Off) All C Motor Base Assembly to C Motor Base Assembly to C Post Assembly All C *Post Elevating Handwheel Assembly All C *Protractor Work Stop & Alignment Gage Assembly All C-10-6 *Rip Fence Assembly All C-7-20 Saw Guide Assemblies (Insert/Special Application) All C-7-18 Saw Guide Assemblies (Insert Types) All C-7-19 Saw Guide Assemblies (Roller Types) All C-3-91 *Sliding Air Table Assembly All C-3-92 *Sliding Air Table Assembly (Shop Air Connection) All C Speed Indicator All C-3-93 Table and Trunnion Assembly All C-3-91 *Table Cylinder (Air Table) All C-4-47 Transmission Assembly All C *Universally Calibrated Work Fixture Assembly All C-5-36 Variable Assembly (6P-A Speedmaster) All C-4-48 Variable Linkage Assembly All C Wheel Hinge Assembly All C *Work Holding Jaw Assembly All C-8-17 *Worklamp Assembly All *Denotes Attachment or Optional Equipment. 1

4 2

5 CODE NO. C-1-71 FINAL ASSEMBLY Ref Final Assembly Chip Box Weldment (Standard) Chip Box Assembly (Dust Spout Option) Drive Assembly (See Detail) * Frame Weldment Knob Assembly DBW-15 Buttwelder Assembly (Optional) (See Welder Manual) Escutcheon (Diameters/X-Section Areas) Escutcheon (Caution) (English) Escutcheon (Caution) (International) Electrical Assembly (See Detail) Escutcheon (Warning) Decal (American Flag) Head Assembly (See Detail) Job Selector Decal (DoALL) Latch Screw, Rd. Hd. Mach. #8-32NC x 3/ Plastic Cover Escutcheon (Warning) (English) Escutcheon (Warning) (International) Upper Saw Guide Assembly (See Detail) Upper Saw Guide Holding Screw * Saw Band (Imperial Bi-Metal Super Silencer) Saw Band Tag Tag (Installation Instructions) Table and Trunnion Assembly (See Detail) Lower Saw Guide Assembly (See Detail) Screw, Soc. Hd. Cap 1/4-20NC x 1-3/ Guard Weldment (Standard) Guard Weldment (Air Table and/or Rip Fence Options) Guard Assembly (Point of Operation) (Optional) (See Detail) Screw, Rd. Hd. Mach. #10-24NC x 3/ Nut, Hex. #10-24NC Washer, Lock #10 Std Escutcheon (Caution) (English) Escutcheon (Caution) (International) Latch Screw, Rd. Hd. Mach. #8-32NC x 3/ Escutcheon (International Only) Screw, Rd. Hd. Drive #2 x 1/ Rear Drive Cover Screw, Hex. Hd. Self-Drill M4.8 x Top Drive Cover Screw, Hex. Hd. Self-Drill M4.8 x Label (1-888-DoALL) Label (Machine Specifications) CE Label (Europa Only)... 1 *NOTE: See Extra Work Height Assembly If Applicable. Following Not Shown: Escutcheon (Government Specifications) Screw, Rd. Hd. Mach. #2 x 1/ Instruction Tag Box of Extra Parts Saw Guide Insert Pack (See Detail) Wrench (Table Tilt) Hex. Key 3/16" Documentation CD Pallet Lubrication Chart (Optional) Shipping Bracket and Hardware (Export Only) Shipping Container (Government)

6 NEW DRG. S.C.L REVISIONS S.C.L S.C.L S.C.L S.C.L GLIDE TABLE OPTION AIR FEED SUB-ASSEMBLY AIR FEED ASSEMBLY MODEL FIRST MACH. LAST MACH V V V V V V C PRINTED IN U.S.A.

7 CODE NO. C-9-32 AIR FEED ASSEMBLY Ref Air Feed Assembly Ref Air Feed Assembly (With Glide Table Option) (20" Machines) Ref Air Feed Assembly (With Glide Table Option) (36" Machines) Air Feed Sub-Assembly (See Detail) Screw, Hex. Hd. Cap 1/4-20NC x 3/ Washer, Lock 1/4 Std Pipe Plug (Brass) (If Supplied) Screw, Hex. Hd. Cap 3/8-16NC x 3/ Washer, Lock 3/8 Std Spacer Washer Carrier and Cable Assembly (Air Feed) (See Detail) Tubing Clamp Screw, Pan Hd. Self-Tap 1/4-20NC x 1/ Street Elbow (Brass) Barbed Insert Hose Clamp Reducer Bushing (Brass) Street Elbow (Brass) Barbed Insert Hose Clamp Screw, Rd. Hd. Mach. 1/4-20NC x 5/ Washer, Lock 1/4 Shakeproof Ext Washer, Flat 1/4 S.A.E. Std Nut, Hex. 1/4-20NC Oil-Fog Lubricator (Includes Bracket) Oil (ASTM 315)... A.R Neoprene Hose 11/16 O.D. (Black)... A.R Air Cylinder Air Filter Screw, Hex. Hd. Cap 1/4-20NC x 1/2 (20" Machines) Screw, Hex. Hd. Cap 3/8-16NC x 7/8 (36" Machines) Washer, Lock 1/4 Std. (20" Machines) Washer, Lock 3/8 Std. (36" Machines) Nut, Hex. Jam 1-14NF Cylinder Mounting Bracket (20" Machines) Cylinder Mounting Bracket (36" Machines) Tubing Clamp Screw, Pan Hd. Self-Tap 1/4-20NC x 1/ Foot Valve Guard Barbed Insert... 2 For Machines with Glide Table Option: Chain Support (13 ) Chain Support (2 ) Screw, Button Hd. Soc. #10-24NC x 1/ Washer, Lock #10 Std Following Not Shown: Work Holding Jaw Assembly (See Detail)... 1 Ref Air Feed Sub-Assembly Reducer Bushing (Brass) Street Elbow (Brass) Barbed Insert Bracket Regulating Valve Gauge Reducer Bushing (Brass) Pipe Coupling (Brass) Pipe Nipple (4") (Brass) Street Elbow (Brass)

8 6

9 CODE NO. C CM AUXILIARY POST SUPPORT ASSEMBLY Ref Auxiliary Post Support Assembly Post Collar Screw, Hex. Hd. Cap 3/8-16NC x 1-1/ Washer, Lock 3/8 Std Upper Post Guide Screw, Hex. Hd. Cap 3/8-16NC x 1-1/ Washer, Lock 3/8 Std Screw, Soc. Set 5/16-18NC x 3/ Back-Up Pad Back-Up Pad Screw 1/2-13NC x 4-1/ Nut, Hex. Jam 1/2-13NC Retaining Ring Escutcheon (Remove Bracket) Support Arm Screw, Hex. Hd. Cap 1/2-13NC x 1-1/ Starwheel Assembly Starwheel Spring Pin Post Clamp Screw Lower Post Guide Auxiliary Post (24" Work Height) Auxiliary Post (30" Work Height) Screw, Soc. Set 5/16-18NC x 3/ Screw, Soc. Set 3/8-16NC x 5/

10 8

11 CODE NO. C-7-23 CM-7-33 BAND FILING ASSEMBLY BAND POLISHING ASSEMBLY Ref Band Filing Assembly (Short Guides, 26" Table) Ref Band Filing Assembly (Long Guides, 26" Table) Ref Band Filing Assembly (Short Guides, 30" Table) Ref Band Filing Assembly (Long Guides, 30" Table) Adaptor File Guide Back-Up File Guide Back-Up Screw Center Plate (Oval) (26" Table) Center Plate (Round) (26" Table) Center Plate (Round) (30" Table) /4" File Guide Assembly (Short Guides) /4" File Guide Assembly (Long Guides) /8" File Guide Assembly (Short Guides) /8" File Guide Assembly (Long Guides) /2" File Guide Assembly (Short Guides) /2" File Guide Assembly (Long Guides) Bracket (1/4", Short Guides) Bracket (1/4", Long Guides) Bracket (3/8", Short Guides) Bracket (3/8", Long Guides) Bracket (1/2", Short Guides) Bracket (1/2", Long Guides) Insert (1/4", Short Guides) Insert (1/4", Long Guides) Insert (3/8", Short Guides) Insert (3/8", Long Guides) Insert (1/2", Short Guides) Insert (1/2", Long Guides) Screw, Rd. Hd. Mach. #4-40NC x 5/8 (1/4" File Guides) Screw, Fill. Hd. Mach. #10-24NC x 5/8 (3/8" & 1/2" File Guides) Washer, Lock #4 Std. (1/4" File Guides) Washer, Lock #10 Std. (3/8" & 1/2" File Guides) Washer (1/4" File Guides) (Between File Guide & Insert) Washer (3/8" & 1/2" File Guides) (Between File Guide & Insert) File Guide (1/4", Short Guides) File Guide (1/4", Long Guides) File Guide (3/8", Short Guides) File Guide (3/8", Long Guides) File Guide (1/2", Short Guides) File Guide (1/2", Long Guides) Guide Plate (1/4", Long Guides Only) Pin (1/4", Long Guides Only)... 2 Ref Band Polishing Assembly (26" Table) Ref Band Polishing Assembly (30" Table) Adaptor Back-Up Screw Guide Back-Up * Center Plate (Oval) (26" Table) (Not Shown) Center Plate (Round) (30" Table) (Not Shown) Band Polishing Sub-Assembly Bracket Screw, Fill. Hd. Mach. #10-24NC x 3/ Back-Up Cloth Adhesive... A.R Back-Up Plate... 1 *NOTE: Some 26" Tables will have the Round Center Plate Used on 30" Tables. 9

12 10

13 CODE NO. C-8-30 CM-8-52 Z-8-26 BAND LUBRICATOR ASSEMBLY Ref Band Lubricator Assembly (Accu-Lube System) Cord Grip Connector ( ) Grommet Tubing Clamp Screw, Rd. Hd. Self-Tap 1/4-20NC x 1/ Electrical Cord (#18-2 Conductor)... A.R Applicator Unit (Includes Hoses, Nozzles, etc.) Cord Grip Connector ( ) Double Support Screw, Soc. Hd. Cap 3/8-16NC x 1/ Block Male Connector Mounting Bracket Screw, Flat Hd. Soc. #6-32NC x 3/ Barbed Insert Screw, Soc. Hd. Cap #6-32NC x 3/ Washer, Flat #6 S.A.E. Std Following Not Shown and Mounted on or Near the Control Box: Selector Switch (2 Position) Escutcheon (Mist Lube)... 1 Ref Band Lubricator Assembly (Unist System) Applicator Unit (Includes Hose) Screw, Hex. Hd. Cap 1/4-20NC x 2-1/ Nut, Hex. 1/4-20NC Washer, Lock 1/4 Std Hose Clamp (Half) Screw, Button Hd. Soc. #10-24NC x 3/ Nozzle Splitter Screw, Button Hd. Soc. 1/4-20NC x 7/ Nut, Hex. Jam 1/4-20NC Washer, Lock 1/4 Std Mounting Bracket Screw, Button Hd. Soc. 1/4-20NC x 3/ Mounting Bracket Screw, Button Hd. Soc. 1/4-20NC x 3/ Street Elbow Pipe Nipple (Brass) Solenoid Valve (3-Way) Solenoid Plug Connector Kit Vent Filter Breather Tubing Clamp Screw, Button Hd. Soc. 1/4-20NC x 3/ Electrical Cord (#18-3 Conductor)... A.R Grommet (If Supplied) Cord Grip Connector ( )... 1 Following Not Shown and Mounted on or Near the Control Box on Selected Models: Selector Switch (2 Position) (Includes Contact Blocks) Escutcheon (Mist Lube)

14 12

15 CODE NO. C CM BANDWHEEL ASSEMBLIES CROWNED BANDWHEELS Ref Bandwheel Assembly (Upper and Idler) Ref Bandwheel Assembly (Lower) Tire Bandwheel (Upper and Idler) Bandwheel (Lower) Ball Bearing (Upper and Idler Bandwheels Only)... 2 FLANGED BANDWHEELS Ref Bandwheel Assembly (Upper and Idler) Ref Bandwheel Assembly (Lower) Tire And Rim Assembly Retainer Screw, Hex. Hd. Cap #10-24NC x 3/ Bandwheel (Upper and Idler) Bandwheel (Lower) Flange Segment Screw, Hex. Hd. Cap #10-24NC x 3/ Ball Bearing (Upper and Idler Bandwheels Only)... 2 Ref Wheel Hinge Assembly Axis Stud Screw, Soc. Set 1/4-20NC x 5/ Block

16 14

17 CODE NO. C-9-33 CARRIER and CABLE ASSEMBLY (Air Feed) Ref Carrier and Cable Assembly Cable Clamp Housing Power Feed Chain Assembly Power Feed Chain Cable Clamp Eye RIvet (3/16 x 7/16) Cable Clamp Hook Cable Clamp Housing Horizontal Pulley Assembly (See Detail) Cable Carrier Nut, Hex. Jam 3/8-16NC Washer, Lock 3/8 Std Equalizer Pulley Assembly (See Detail) Vertical Pulley Assembly (See Detail) Power Feed Cord Handwheel Washer, Flat 1/2 S.A.E. Std Ref Horizontal Pulley Assembly Cap Pulley Screw, Hex. Hd. Cap 1/4-20NC x 3/ Washer, Lock 1/4 Shakeproof Pulley Spacer Washer, Flat 3/8 Wrought Thumb Nut Pulley Screw... 1 Ref Equalizer Pulley Assembly Cap Pulley Pulley Axis Retaining Ring Clevis... 1 Ref Vertical Pulley Assembly Cap Pulley Washer, Lock 1/4 Shakeproof Pulley Stud Screw, Hex. Hd. Cap 1/4-20NC x 3/ Pulley Spacer

18 16

19 CODE NO. C-9-34 CHIP BLOWER ASSEMBLY Ref Chip Blower Assembly Ref Chip Blower Assemby (w/sliding Air Table Option) Orifice (.038) (Brass) Close Nipple (Brass) Street Elbow Anchor Connector Barbed Insert Hose Clamp Neoprene Hose 11/16 O.D.... A.R Tubing Clamp Screw, Button Hd. Soc. 1/4-20NC x 3/ Street Elbow Barbed Insert Valve Coolant And Air Hose Connector Segmented Hose (Specify Length)... A.R Nozzle... 1 When Air Table is Also Supplied: Service Tee (Brass)... 1 Following Not Shown and Used When Air Compressor Option is Supplied: Air Compressor (1/8 H.P.) Air Compressor (1/4 H.P.) Screw, Hex. Hd. Cap 5/16-18NC x 5/ Washer, Lock 5/16 Std Cord Grip Connector ( ) Electrical Cord (#14-4 Conductor)... A.R. 17

20 18

21 CODE NO. C-10-2 CM-9-1 Z-9-4 DISC CUTTER ASSEMBLY Ref Disc Cutter Assembly (Rear Mounted) Ref Disc Cutter Assembly (Side Mounted) Bracket (Rear Mounted) Bracket (Side Mounted) Spring Pin (Rear Mounted) Spring Pin (Side Mounted) Radius Arm Clamp Screw, Hex. Hd. Cap 3/8-16NC x Washer, Lock 3/8 Std Adjustment Rod (w/ # Adhesive) Radius Arm Adjustment Housing Spring Pin Screw, Hex. Hd. Cap 3/8-16NC x Washer, Lock 3/8 Std Center Pin Clamp Adjustment Wheel Center Adjusting Tube Center Pin Screw, Hex. Hd. Cap 5/16-18NC x Washer, Lock 5/16 Std Following Not Shown and Used For Mounting to the Post: Screw, Hex. Hd. Cap 5/16-18NC x 1 (Rear Mounted) Screw, Hex. Hd. Cap 5/16-18NC x 1-1/2 (Side Mounted) Washer, Flat 5/16 S.A.E. Std Washer, Lock 5/16 Std Cloth Bag Wrench (If Suppled)

22 20

23 CODE NO. C DRIVE ASSEMBLY Ref Drive Assembly (2013-V) Ref Drive Assembly (3613-1) Brush Holder Weldment Wheel Brush Screw, Button Hd. Soc. 1/4-20NC x 1/ Dowel Pin Spacer (.014/.016)... A.R Spacer (.028/.032)... A.R Spacer (.127/.143)... A.R Nut, Hex. Jam 3/4-10NC Washer, Lock 3/4 Shakeproof Ext Washer, Flat 3/4 S.A.E. Std Bandwheel Assembly (See Detail) Woodruff Key Screw, Hex. Hd. Cap 5/16-18NC x 1-1/ Washer, Lock 5/16 Std Screw, Soc. Hd. Cap 1/4-20NC x 1/ Washer, Lock 1/4 Std Adaptor Screw, Soc. Hd. Shoulder 1/4-20NC x 3/ Shift Arm Mounting Bracket Screw, Soc. Hd. Shoulder 1/4-20NC x 3/ Washer, Lock 1/4 Std Nut, Hex. 1/4-20NC Shift Lever Escutcheon (Band Speed) (Feet/English) Escutcheon (Band Speed) (Metric/ International) Lockout Plate Weldment Pointer Plate Screw, Hex. Hd. Cap #10-24NC x 1/ Spacer Strap Spacer Screw, Button Hd. Soc. #10-24NC x 1/ Washer, Lock #10 Std Nut, Hex. #10-24NC Spring Pin Nylon Tubing 3/16 O.D.... A.R Wire Strap Screw, Button Hd. Soc. #10-24NC x 1/ Bracket Screw, Button Hd. Soc. 1/4-20NC x 1/ Variable Linkage Sub-Assembly (See Detail) Shim (.035)... A.R Shim (.0149)... A.R Shim (.005)... A.R Shim (.003)... A.R Screw, Hex. Hd. Cap 3/8-16NC x Washer, Lock 3/8 Std Angle Bracket Screw, Hex. Hd. Cap 3/8-16NC x 3/ Washer, Lock 3/8 Std * Pivot Rod Cotter Pin Motor Base Assembly (See Detail) Nut, Hex. Jam 3/8-16NC Plastic Tubing 1/2 O.D.... A.R Fabreeka Washer Spring Washer, Flat 3/8 S.A.E. Std Screw, Hex. Hd. Cap 3/8-16NC x 7-3/ V-Belt (3 Phase Motors) Variable Assembly (6P-A Speedmaster) (See Detail) Screw, Soc. Set 5/16-18NC x V-Belt Pulley Screw, Soc. Set 5/16-18NC x 1/ Key Transmission Assembly (See Detail) Shim (.005)... A.R Shim (.008)... A.R Shim (.010)... A.R Shim (.020)... A.R. Not Shown and Located on Drive Cover Weldment and Used on Model 2013-V With 220V/50 Hz, Single Phase Motors Only: Cover Screw, Button Hd. Soc. #10-24NC x 1/4 1 *NOTE: Item #51 was Before Serial # on 2013-V and # on

24 22

25 CODE NO. C-6-32 ELECTRICAL ASSEMBLY Ref. Electrical Assembly Limit Switch (Door Interlock) Screw, Soc. Hd. Cap #6-32NC x 1-1/ Cord Grip Connector ( ) Mounting Bracket (Limit Switch Key) Shim (.032)... A.R Screw, Soc. Hd. Cap #4-40NC x 3/ Washer, Flat #4 S.A.E. Std Washer, Lock #4 Std Nut, Hex. #4-40NC Grommet Electrical Cord (#18-2 Conductor)... A.R Worklamp Assembly (Standard Option) (See Detail) Worklamp Assembly (Extra Work Height Option) (See Detail) Mounting Bracket (Limit Switch Key) Shim (.032)... A.R Screw, Soc. Hd. Cap #4-40NC x 3/ Washer, Flat #4 S.A.E. Std Washer, Lock #4 Std Nut, Hex. #4-40NC Limit Switch (Door Interlock) Screw, Soc. Hd. Cap #6-32NC x 1-1/ Cord Grip Connector ( ) Electrical Cord (#18-2 Conductor)... A.R Hose Clip Screw, Soc. Hd. Cap #8-32NC x 3/ Electrical Control Box Assembly (See Detail) Cord Grip Connector ( ) Cord Grip Connector ( ) Electrical Cord (#10-3 Conductor) (115V, 1 Phase)... A.R Electrical Cord (#12-3 Conductor) (220V, 1 Phase)... A.R Electrical Cord (#14-4 Conductor) (3 Phase Motors)... A.R Screw, Hex. Hd. Cap 1/4-20NC x 3/ Washer, Lock 1/4 Std Washer, Flat 1/4 S.A.E. Std Cord Grip Connector ( ) Hole Seal (When Worklight Not Supplied) Grommet Grommet... 1 Following Not Shown: Escutcheon (Limit Switch No.) Screw, Rd. Hd. Drive #2 x 1/

26 24

27 CODE NO. C-6-33 ELECTRICAL CONTROL BOX ASSEMBLY Ref. Electrical Control Box Assembly Grounding Bus Screw, Pan Hd. Slotted M6-1.0 x Screw, Pan Hd. Slotted M6-1.0 x Screw, Pan Hd. Slotted M5-0.8 x Washer, Flat M Terminal Lug *. Soft Start Option ( V) *. Soft Start Option ( V) *. Soft Start Option ( V) *. Soft Start Option ( V) (Single Phase) Transformer (208V) Transformer (220V, 230V, 460V, 575V) Transformer (400V) Nut, Hex. 1/4-20NC Washer, Flat 1/4 S.A.E. Std Wire Terminal (#10) Wire Terminal (#8 Stud, Locking) Fuse Block (208V, 230V, 460V, 575V) Circuit Breaker (220V) Circuit Breaker (400V) Fuse Block (115 Single Phase) Fuse Block (220 Single Phase) Fuse (15 Amp) (208V) Fuse (10 Amp) (230V) Fuse (5 Amp) (460V, 575V) Fuse (25 Amp) (115V Single Phase) Fuse (20 Amp) (220V Single Phase) End Stop Fuse Block Circuit Breaker (220V, 400V) Fuse (1.6 Amp) (115V, 208V, 230V, 460V, 575V) Contactor Contactor (Single Phase Motors) Enclosure Weldment End Stop Circuit Breaker (Buttwelder Option) Fuse Block (575V Only) (Buttwelder Option) Fuse (8 Amp) (575V Only) (Buttwelder Option) Nut Rivet M Overload Relay (208V, 220V) Overload Relay (230V) Overload Relay (400V, (460V, 575V) Overload Relay (115V Single Phase) Overload Relay (220V Single Phase) Terminal Block... A.R End Section End Stop Terminal Block Marker Set Escutcheon Pushbutton Operator (Red Mushroom, Twist to Reset) Contact Block (1-NC) E-Stop Marker (Yellow) Pushbutton Operator (Green) Contact Block (1-NO) Hole Seal (No Worklight Option)... 1 * Selector Switch (2 Position) * Contact Block (1-NO) Gasket Strip... A.R. 38** Disconnect Switch ** Disconnect Switch Shaft ** Disconnect Switch Handle Push Nut Retainer Screw, Hex. Hd. Captive M5-0.8 x Washer, Nylon # Label (Electrical Hazard) Fuse/Overload Schedule... 1 Following Not Shown: U.L. Label Wire, #14 Black (19 Strand)... A.R Wire, #14 Green/Yellow (19 Strand)... A.R Wire, #16 Red (19 Strand)... A.R Wire, #16 White (19 Strand)... A.R Wire, #16 Green/Yellow (19 Strand)... A.R Ground ID Shrink Tube (50 Hz Only)... A.R Wire Terminal (#10 Stud) (50 Hz)... A.R Hour Meter (Optional) Nut, Hex. #4-40NC Washer, Lock #5 Shakeproof Ext Fan (Air Compressor Option) Fan Cover (Air Compressor Option) Fan Lead Wire (Air Compressor Option) 1 *If Supplied. **NOTE: Before Serial # (Excluding 703 & 705): Order Disconnect Switch Service Kit - # Otherwise, Use Part Numbers Listed. 25

28 26

29 CODE NO. C CM EXTRA WORK HEIGHT ASSEMBLY Ref " Work Height Assembly (2019-V, 2019-V3, 2019-V5) Ref " Work Height Assembly (2018-VH, 2018-D12) Ref " Work Height Assembly (2025-V, 2025-V3, 2025-V5) Ref " Work Height Assembly (2024-VH, 2024-D12) Ref " Work Height Assembly (2031-V, 2031-V3, 2031-V5) Ref " Work Height Assembly (2030-VH, 2030-D12) Auxiliary Post Support Assembly (Work Heights Over 19") (See Detail) Worklamp Assembly (Optional) Post Elevating Handwheel Assembly (18 and 19" Work Heights) (See Detail) Post Elevating Handwheel Assembly (24 and 25" Work Heights) (See Detail) Post Elevating Handwheel Assembly (30 and 31" Work Heights) (See Detail) Saw Band Guard Assembly (18 and 19" Work Heights) Saw Band Guard Assembly (24 and 25" Work Heights) Saw Band Guard Assembly (30 and 31" Work Heights) Guard Weldment (18 and 19" Work Heights) Guard Weldment (24 and 25" Work Heights) Guard Weldment (30 and 31" Work Heights) Guard Slide Cover Thumb Screw Spring Pin (Work Heights Over 19" Only) * Guard Slide (Post) (8-5/8") (V, V3, V5 Only)... 1 * Guard Slide (Post) (14-5/8") (V, V3, V5 Only)... 1 * Guard Slide (Post) (20-5/8") (V, V3, V5 Only)... 1 * Guard Slide (Post) (6-5/8") (VH, D12 Only)... 1 * Guard Slide (Post) (12-5/8") (VH, D12 Only)... 1 * Guard Slide (Post) (18-5/8") (VH, D12 Only) Thumb Screw Saw Band (Super Silencer) (18" and 19" Work Heights) Saw Band (Super Silencer) (24" and 25" Work Heights) (V, V3, V5 Only) Saw Band (Super Silencer) (24" and 25" Work Heights) (VH, D12 Only) Saw Band (Super Silencer) (30" and 31" Work Heights) Frame Weldment (18 and 19" Work Heights) Frame Weldment (24 and 25" Work Heights) Frame Weldment (30 and 31" Work Heights) Post Screw Cover Weldment (24, 25, 30, 31 Post Elevating Handwheel Options) Screw, Hex. Hd. Cap 1/4-20NC x 5/ Washer, Lock 1/4 Std Nut, Hex. 1/4-20NC... 4 *NOTE: Use These Interchangeable Guard Slides When Applicable. Be Sure To Use The Guard Slide That Will Cover Exposed Saw Band Completely. 27

30 28

31 CODE NO. C-3-46 GLIDE TABLE ASSEMBLY Ref Glide Table Assembly (12" Stroke) Ref Glide Table Assembly (18" Stroke) Stop Plate (12" Stroke) Stop Plate (18" Stroke) Screw, Button Hd. Soc. #8-32NC x 3/ Center Plate (Oval) Table (12" Stroke) Table Weldment (18" Stroke) Guide Wheel Bushing Adaptor (L.H. Side) Screw, Hex. Hd. Cap 5/16-18NC x 1-1/ Washer, Lock 5/16 Std Dowel Pin Lower Post Block Screw, Hex. Hd. Cap 3/8-16NC x Washer, Lock 3/8 Std Thumbscrew Weldment Lanyard Screw, Soc. Hd. Cap 1/4-20NC x 5/ End Bar (12" Stroke) End Bar Weldment (18" Stroke) Guide Wheel Adjustable Bushing Adaptor (R.H. Side) Screw, Hex. Hd. Cap 5/16-18NC x 1-1/ Washer, Lock 5/16 Std Screw, Soc. Hd. Cap 1/2-13NC x 1-1/ Washer, Lock 1/2 Std Screw, Soc. Set 5/16-18NC x 1-1/ Screw, Soc. Hd. Cap 1/4-20NC x 5/ Track (12" Stroke) Track (18" Stroke) Roller Support Weldment (12" Stroke) Glide Table Plate (18 Stroke) Stop Block (12" Stroke) Stop Block (18" Stroke) Screw, Button Hd. Soc. 1/4-20NC x 1-1/ Front Table Clamp Glide Table Handle Screw, Hex. Hd. Cap 3/8-16NC x 3/ Washer, Flat 3/8 S.A.E. Std Screw, Hex. Hd. Cap 3/8-16NC x Washer, Flat 3/8 S.A.E. Std Dowel Pin Screw, Soc. Hd. Cap 1/2-13NC x Table Support Weldment (12" Stroke) Table Support Weldment (18" Stroke) Screw, Hex. Hd. Cap 3/8-16NC x Washer, Lock 3/8 Std

32 30

33 CODE NO. C GUARD ASSEMBLY (Point of Operation) Ref Guard Assembly (Point of Operation) Guard Mounting Plate Thumb Screw Assembly Knob Screw, Soc. Hd. Cap #10-24NC x 3/ Spacer Upper Guard (Plexiglas) Telescoping Guard Lower Guard Escutcheon (Guard Position) Thumb Screw Nut Plate 1/4-20NC

34 32

35 CODE NO. C HEAD ASSEMBLY Ref Head Assembly Pin Retaining Ring Spring Pin Screw, Soc. Hd. Cap 5/16-18NC x Washer, Lock 5/16 Std Screw, Soc. Set 5/16-18NC x Head Casting Bandwheel Assembly (See Detail) Head Slide Weldment Screw, Soc. Set 1/4-20NC x 5/8 (Self Locking, Half Dog Point) Wheel Hinge Assembly (See Detail) Band Tension Screw Sub-Assembly Adaptor Screw Spring Pin Nut, Hex. Jam 1/2-13NC Spring Pin Washer, Flat 1/2 S.A.E. Std Thrust Ball Bearing Angle Lock Handle Bearing Locknut Bearing Lockwasher Tilting Screw Handle (w/stud) Compression Spring Washer, Flat 5/8 S.A.E. Std Band Tension Pointer Screw, Hex. Hd. Cap #10-24NC x 1/ Washer, Lock #10 Std Nut, Hex. #10-24NC Escutcheon (Band Tension) (Inch/English) Escutcheon (Band Tension) (Metric/International) Nut, Hex. Jam 5/16-18NC Retaining Compound (Loctite #271 )... A.R. 31* Guard Weldment (Standard) Guard Slide Cover Thumb Screw * Post Assembly (Standard) (2013-V, 2013-V3, 2013-V5) (See Detail). 1 * Post Assembly (Standard) (3613-1, 3613-V3, 3613-V5) (See Detail).. 1 * Post Elevating Handwheel Assembly (Standard - Optional) (See Detail) 1 *NOTE: See Extra Work Height Assembly If Applicable. Following Not Shown: Escutcheon (Post - Raise/Lower) (International) Screw, Rd. Hd. Drive #2 x 3/

36 34

37 CODE NO. C CM Z LASER LINE GENERATOR ASSEMBLY Ref. Laser Line Generator Assembly Label (Caution - Laser) Laser Mounting Bracket Weldment Laser Mounting Bracket Weldment (ZV-3620 Only) Screw, Soc. Hd. Cap M6-1.0 x Washer, Flat M Washer, Lock M Laser Cordset Laser Line Generator (Red) (24VDC) Laser Holder Screw, Soc. Hd. Cap M6-1.0 x

38 36

39 CODE NO. C-8-16 MIST COOLANT ASSEMBLY Ref Mist Coolant Assembly Ref Mist Coolant Assembly (w/sliding Air Table Option) Barbed Insert Hose Clamp Street Elbow Ball Valve Close Nipple (Brass) Street Elbow Anchor Connection Orifice (.038) (Brass) Close Nipple (Brass) Neoprene Hose 11/16 O.D. (Black)... A.R Tubing Clamp Screw, Button Hd. Soc. 1/4-20NC x 3/ Bracket Screw, Rd. Hd. Self-Tap 1/4-20NC x 3/ Bottle Assembly Plastic Tubing 3/8 O.D. (Clear)... A.R Hose Clamp Coolant Manifold Assembly (Standard) Coolant Manifold Assembly (19 Work Height) Coolant Manifold Assembly (25 Work Height) Coolant Manifold Assembly (31 Work Height) Coolant And Air Hose (Standard) Coolant And Air Hose (19 Work Height) Coolant And Air Hose (25 Work Height) Coolant And Air Hose (31 Work Height) Connector Segmented Hose (Specify Length)... A.R Nozzle Barbed Insert Sight Feed Valve Manifold Coolant Tube Assembly Nylon Tubing.089 O.D. (Cut to Length)... A.R Glue (Meta Grip #3802)... A.R Pipe Plug Street Elbow Barbed Insert Hose Clamp... 1 When Air Table is Also Supplied: Service Tee

40 38

41 CODE NO. C Z-10-6 MITRE ASSEMBLY Ref Mitre Assembly (No. 2 Standard Cut-Off) (20" Table) Ref Mitre Assembly (No. 2 Standard Cut-Off) (24" Table) Ref Mitre Assembly (No. 2 Standard Cut-Off) (26" Table) Ref Mitre Assembly (No. 2 Standard Cut-Off) (30" Table) Screw, Soc. Set 1/4-20NC x 5/ Stop Collar Screw, Soc. Hd. Cap #10-24NC x 1/ Rear Slide Rod Bracket (20" Table) Rear Slide Rod Bracket (24", 26", 30" Tables) Screw, Soc. Hd. Cap 3/8-16NC x 1/2 (20", 30" Table) Screw, Soc. Hd. Cap 3/8-16NC x 3/4 (24", 26" Table) Spacer Washer (26" Table Only) Slide Rod (20" Table) Slide Rod (24" Table) Slide Rod (26" Table) Slide Rod (30" Table) Screw, Soc. Hd. Cap 3/8-16NC x 1/2 (20", 30" Tables) Screw, Soc. Hd. Cap 3/8-16NC x 3/4 (24", 26" Tables) Spacer Washer (26" Table Only) Front Slide Rod Bracket (20" Table) Front Slide Rod Bracket (24", 26", 30" Tables) Screw, Soc. Set 1/4-20NC x 5/ Mitre Sub-Assembly (20", 24" Table) Mitre Sub-Assembly (26" Table) Mitre Sub-Assembly (30" Table) Locking Stud Washer Stud Roll Pin Mitre Head Pivot Pivot Washer Pointer Screw, Truss Hd. Mach. #8-32NC x 1/ Roll Pin Screw, Soc. Hd. Cap 1/4-20NC x 1/ Gauge Rod Mitre Bar (20", 24" Table) Mitre Bar (26" Table) Mitre Bar (30" Table) Degree Plate Screw, Rd. Hd. Drive #4 x 1/ Thumb Screw Mitre Head Handwheel Slide Arm

42 40

43 CODE NO. C MOTOR BASE ASSEMBLY Ref. Motor Base Assembly *. Motor Base Plate Motor Base Plate (Single Phase) Screw, Hex. Hd. Cap 3/8-16NC x 1-1/ Screw, Hex. Hd. Cap 5/16-18NC x 1-1/4 (Single Phase) Washer, Flat 3/8 Wrought Washer, Flat 5/16 Wrought (Single Phase) Nut, Hex. 3/8-16NC Nut, Hex. 5/16-18NC (Single Phase) Electric Motor (208V, 230V, 460V) Electric Motor (575V) Electric Motor (200V, 400V) Electric Motor (115V/60 Hz, 1 Phase) Electric Motor (220V/50 Hz, 1 Phase) Electric Motor (380V; 60 Hz) **. Pulley (60 Hz) **. Pulley (50 Hz) Pulley (115V/60 Hz, 1 Phase) Pulley (220V/50 Hz, 1 Phase) Screw, Soc. Set 1/4-20NC x 1/ Cord Grip Connector Flange Washer Bond Nut... 1 Following Not Shown: Motor Terminal Block (50 Hz Only)... 1 *NOTE: Before Serial # , Item #1 Was **NOTE: Before Serial # , Items #5 were Pulley (60Hz) and # Pulley (50 Hz). 41

44 42

45 CODE NO. C MOTOR BASE ASSEMBLY Ref. Motor Base Assembly Motor Base Plate Screw, Hex. Hd. Cap 5/16-18NC x 1-1/ Screw, Hex. Hd. Cap 3/8-16NC x 1-1/4 (50 Hz Only) Washer, Flat 5/16 Wrought Washer, Flat 3/8 Wrought (50 Hz Only) Nut, Hex. 5/16-18NC Nut, Hex. 3/8-16NC (50 Hz Only) Washer, Lock 5/16 Std Washer, Lock 3/8 Std. (50 Hz Only) Electric Motor (208V, 230V, 460V) Electric Motor (575V) Electric Motor (200V, 400V) Electric Motor (115V, 220V, 60 Hz, 1 Phase) Electric Motor (380V; 60 Hz) Pulley 208V, 230V, 460V and 60 Hz Single Phase Motors) Pulley (575V Only) Pulley (50 Hz) Screw, Soc. Set 1/4-20NC x 1/ Cord Grip Connector Flange Washer Bond Nut... 1 Following Not Shown: Wire Connector (Yellow)

46 44

47 CODE NO. C POST ASSEMBLY Ref Post Assembly (Standard) Ref Post Assembly (19 Work Height) Ref Post Assembly (25 Work Height) Ref Post Assembly (31 Work Height) Post (21.50 ) (Standard) Post (32.12 ) (19 Work Height) Post (38.12 ) (25 Work Height) Post (44.12 ) (31 Work Height) Post Slide Casting Lockscrew Sub-Assembly Adaptor Spring Pin Brass Stud Spring Plunger Screw, Soc. Hd. Cap 3/8-16NC x 1-1/ Washer, Lock 3/8 Std Post Slide Plate Screw, Soc. Hd. Shoulder 5/16-18NC x 1/ Screw, Fill. Hd. Mach. #10-24NC x 1/ Screw, Soc. Set 3/8-24NF x Spring Pin Guard Stop Bracket

48 46

49 CODE NO. C CM POST ELEVATING HANDWHEEL ASSEMBLY Ref Post Elevating Handwheel Assembly (Standard) Ref Post Elevating Handwheel Assembly (18 and 19 Work Heights) Ref Post Elevating Handwheel Assembly (24 and 25 Work Heights) Ref Post Elevating Handwheel Assembly (30 and 31 Work Heights) Screw, Soc. Hd. Cap 1/4-20NC x 1-1/ Washer, Lock 1/4 Shakeproof Post (25.94 ) (Standard) Post (31.94 ) (18 and 19 Work Heights) Post (37.94 ) (24 and 25 Work Heights) Post (43.94 ) (30 and 31 Work Heights) Dowel Pin Screw, Soc. Hd. Cap 1/4-20NC x Screw, Soc. Set 5/16-18NC x 3/4 (Flat Pt.) Cover Guard Stop Weldment Screw, Hex. Hd. Cap #10-24NC x 3/ Washer, Lock #10 S.A.E. Std Bevel Gear Spring Pin Thrust Ball Bearing Tubing Housing Retaining Ring Spacer... A.R Spring Pin Bearing Handwheel Pin Spring Pin Screw, Soc. Set 1/4-20NC x 1/ Compression Spring Friction Plug Spring Pin Bevel Gear Shaft (21.88 ) (Standard) Shaft (27.88 ) (18 and 19 Work Heights) Shaft (33.88 ) (24 and 25 Work Heights) Shaft (39.88 ) (30 and 31 Work Heights) Nut

50 48

51 CODE NO. C CM-10-7 PROTRACTOR WORK STOP and ALIGNMENT GAGE ASSEMBLY Ref.* Protractor Work Stop And Aligning Gage Assembly Gage Rod Dowel Pin * T-Nut Miter Head Thumbnut Knob * Stud Pointer Screw, Rd. Hd. Mach. #10-24NC x 3/ Washer, Flat 7/16 S.A.E. Std Shaft Protractor Plate Screw, Rd. Hd. Mach. #10-24NC x 3/ *NOTE: For Model 26-HB2 Ref Protractor Work Stop And Aligning Gage Assembly T-Nut Stud

52 50

53 CODE NO. C-10-6 Z-9-5 RIP FENCE ASSEMBLY Ref Rip Fence Assembly (24" Table) Ref Rip Fence Assembly (26" Table) Ref Rip Fence Assembly (30" Table) Clamp Guide (24" and 26" Tables) Clamp Guide (30" Table) Screw, Soc. Hd. Cap 3/8-16NC x 3/ Spacer Washer (If Supplied) Rip Fence Sub-Assembly (24" Table) Rip Fence Sub-Assembly (26" and 30" Table) Clamp (24" Table) Clamp (26" and 30" Tables) Screw, Soc. Hd. Cap 3/8-16NC x 3/ Work Guide (24" Table) Work Guide (26" and 30" Tables) Clamp Bar Screw Screw, Soc. Set 1/4-20NC x 1/ Clamp Bar Spring Clip Handwheel Assembly... 1 Following Not Shown: Tag (Rip Fence Alignment)

54 52

55 CODE NO. C-7-20 CM-7-29 SAW GUIDE ASSEMBLIES HIGH SPEED SAW GUIDES (Standard For Crowned Bandwheels) Ref Upper Saw Guide Assembly (High Speed) (1/16-1/2 ) 1* Ball Bearing Retaining Ring (If Supplied) * Bearing Cap * Spacer Screw, Soc. Hd. Cap 1/4-20NC x 5/ Insert Washer Upper Saw Guide Block Hole Plug (If Supplied)... 1 Ref Lower Saw Guide Assembly (High Speed) (1/16-1/2 )... 1* Ball Bearing Retaining Ring (If Supplied) * Bearing Cap * Spacer Screw, Soc. Hd. Cap 1/4-20NC x 5/ Insert Washer Lower Saw Guide Block Hole Plug (If Supplied)... 1 *NOTE: When ordering any of the marked items, ordering # Bearing Replacement Kit is recommended. STANDARD FOR FLANGE BANDWHEELS Ref Upper Saw Guide Assy (Carbide Insert) Screw, Soc. Hd. Cap 1/4-20NC x 1-1/ Insert Washer Upper Saw Guide Block Back-Up Insert Pivot Bolt... 1 Ref Lower Saw Guide Assy (Carbide Insert) Back-up Insert Pivot Bolt Screw, Soc. Hd. Cap 1/4-20NC x 1-1/ Insert Washer Lower Saw Guide Block SAW GUIDE ASSEMBLY Ref Saw Guide Assy (26 Table) Ref Saw Guide Assy (30 Table) Screw, Soc. Hd. Cap 1/4-20NC x Upper Angle Saw Guide Bracket Lower Angle Saw Guide Bracket Pipe Nipple Elbow Screw, Soc. Hd. Cap 1/4-20NC x 3/ Center Plate (Oval) (Not Shown) Center Plate (Round)(Not Shown) Chip Baffle (If Supplied) (Not Shown) Thumb Screw (Not Shown)... 1 ADJUSTABLE SAW GUIDE ASSEMBLIES Ref Adjustable Angle Saw Guide Set (26 Table) Ref Adjustable Angle Saw Guide Set (30 Table) Upper Saw Guide Holding Screw Adaptor Bar Screw, Soc. Hd. Cap 1/4-20NC x Screw, Soc. Hd. Cap 1/4-20NC x 7/ Cap Screw, Flat Hd. Mach. #6-32NC x 3/ Upper Saw Guide Housing Label (Logo) Label (Warning) Lower Saw Guide Housing Spring Plunger Split Ring Roller Bearing Eccentric Stud Roller Bearing Dowel Pin Upper Saw Guide Lower Saw Guide Roller Bearing Concentric Stud Sleeve Cap Spring Pin Locknut #10-24NC... 4 Following Not Shown: Gage Saw Band Guard Assembly Guard Weldment Sliding Guard Thumb Screw Center Plate (26 Table) Center Plate (30 Table)... 1 SAW GUIDE INSERT GAGE Insert Gage (.025) Insert Gage (.032) Insert Gage (.035) Box (For Inserts and Gages)... 1 SAW GUIDE INSERT SELECTION STEEL SIZE CARBIDE / / / / / / / / /

56 54

57 CODE NO. C-7-18 CM-7-23 SAW GUIDE ASSEMBLIES HEAVY DUTY SAW GUIDE ASSEMBLY (CARBIDE BACK-UP) Ref Upper Saw Guide Assembly (1/16-1/2 Bands) Ref Upper Saw Guide Assembly (5/8-3/4 Bands) Ref Upper Saw Guide Assembly (1 Band) Ref.* Upper Saw Guide Assembly (1 Bands w/ Coolant Line) Screw, Soc. Hd. Cap 1/4-20NC x 5/8 (1/16 1/2 ) Screw, Soc. Hd. Cap 1/4-20NC x 1 (5/8 3/4 ) Screw, Soc. Hd. Cap 1/4-20NC x 1-1/4 (1 ; Coolant Line) Insert Washer Screw, Soc. Set 5/16-24NF x 1/2 (5/8, 3/4, 1 ) Coolant Nozzle (Coolant Line) Upper Saw Guide Block (1/16-1/2 ) Upper Saw Guide Block (5/8, 3/4 ) Upper Saw Guide Block (1 ) Upper Saw Guide Block (W/Coolant Line) Locknut (5/8, 3/4, 1 ) Pipe Plug (5/8, 3/4, 1 ) *. 90 Barbed Insert (Coolant Line) Guide Guard (5/8, 3/4, 1 ) Bearing Cap Ass y. (Includes Carbide) Ball Bearing Retaining Ring Spacer (Between Bearings)... 1 * Models , H, , , , 6013-H3 Only. NOTE: If your Machine has 2 Coolant Lines to the Upper Saw Guide, Delete This Item and Replace With the Following: Swivel Joint Barbed Insert... 2 Ref Lower Saw Guide Assembly (1/16-1/2 Bands) Ref Lower Saw Guide Assembly (5/8-3/4 Bands) Ref Lower Saw Guide Assembly (1 Band) Bearing Cap Ass y. (Includes Carbide) Ball Bearing Retaining Ring Spacer (Between Bearings) Lower Saw Guide Block (1/16-1/ Lower Saw Guide Block (5/8, 3/4 ) Lower Saw Guide Block (1 ) Screw, Soc. Hd. Cap 1/4-20NC x 5/8 (1/16 1/2 ) Screw, Soc. Hd. Cap 1/4-20NC x 1 (5/8 3/4 ) Screw, Soc. Hd. Cap 1/4-20NC x 1-1/4 (1 ; Coolant Line) Insert Washer... 2 SAW GUIDE INSERT SELECTION STEEL SIZE CARBIDE / / / / / / / / / HEAVY DUTY SAW GUIDE ASSEMBLY (STEEL BACK-UP) Ref Upper Saw Guide Assembly (1/16-1/2 Bands) Ref Upper Saw Guide Assembly (5/8-3/4 Bands) Ref Upper Saw Guide Assembly (1 Band) Screw, Soc. Hd. Cap 1/4-20NC x 1-1/4 (1/16 1/2, 1 ) Screw, Soc. Hd. Cap 1/4-20NC x 1 (5/8 3/4 ) Insert Washer Screw, Soc. Set 5/16-24NF x 1/2 (5/8, 3/4, 1 ) Upper Saw Guide Block (1/16-1/2 ) Upper Saw Guide Block (5/8, 3/4 ) Upper Saw Guide Block (1 ) Pipe Plug (5/8, 3/4, 1 ) Bearing Cap Ball Bearing Retaining Ring Spacer (Between Bearings)... 1 Ref Lower Saw Guide Assembly (1/16-1/2 ) Ref Lower Saw Guide Assembly (5/8-3/4 ) Ref Lower Saw Guide Assembly (1 ) Bearing Cap Ball Bearing Retaining Ring Spacer (Between Bearings) Lower Saw Guide Block (1/16-1/2 ) Lower Saw Guide Block (5/8, 3/4 ) Lower Saw Guide Block (1 ) Screw, Soc. Hd. Cap 1/4-20NC x 1-1/4 (1/16-1/2, 1 ) Screw, Soc. Hd. Cap 1/4-20NC x 1 (5/8-3/4 ) Insert Washer... 2 PRECISION SAW GUIDE ASSEMBLY (1/16 1/2 Bands) Ref Precision Upper Saw Guide Assembly Screw, Soc. Hd. Cap 1/4-20NC x 5/ Insert Washer Screw, Soc. Set 5/16-24NF x 1/ Upper Saw Guide Block Screw, Soc. Set #8-32NC x 1/4 (Cone Pt.) Pipe Plug Bearing Sub-Assembly (See Detail)... 1 Ref Precision Lower Saw Guide Assembly Screw, Soc. Hd. Cap 1/4-20NC x 5/ Insert Washer Bearing Sub-Assembly (See Detail) Lower Saw Guide Block Screw, Soc. Set #8-32NC x 1/4 (Cone Pt.) 1 Ref Bearing Sub-Assembly Shaft Ball Bearing Washer Roller Seal... 1 SAW GUIDE INSERT SELECTION Insert Gage (.025) Insert Gage (.032) Insert Gage (.035) Box (For Inserts and Gages)