Equipment Safety Briefings
|
|
- Cora Henry
- 5 years ago
- Views:
Transcription
1 Equipment Safety Briefings
2 Table Saw Although the table saw is one of the most useful machines in the shop, it is also one of the most dangerous. It can be used to accurately rip and crosscut lumber and sheet goods. The table saw can also be used for special operations including cutting dadoes and rabbets and for re-sawing. With the use of special jigs, joinery like tenons and box joints can be made. In addition, the blade can be tilted for cutting bevels and mitres.
3 Table Saw One of the table saws at RSS are SawStops, considered the safest in the industry. SawStop saws are equipped with a safety system that detects when someone accidentally contacts the spinning saw blade, and then stops the blade in milliseconds.
4 The SawStop has a built-in MAIN POWER SWITCH. When you flip the switch on, red and green lights flash for approximately 20 seconds as the system runs through a safety check. When the red light turns off and the green light remains on, the saw is ready. Table Saw
5 Table Saw Anatomy Throat Insert Blade Guard Table Fence Fence Lock Guide Rail Blade Bevel Wheel Main Breaker Power Mitre Track Blade Height Wheel
6 Table Saw Anatomy Riving Knife (Splitter) Blade Guard Throat Insert
7 Saw Blade Parts Kerf: Width of the tooth, typically 1/8 Gullet: Clearing away cuttings Bevel: Angle of the tooth
8 Saw Blade Types
9 Saw Blade Types
10 Saw Blade Teeth Patterns
11 Saw Blade Teeth Patterns
12 Table Saw Safety a) The number one cause of injuries on the table saw is kickback. Kickback occurs when the operator loses control of the material being cut and it is thrown from the machine with great force. b) Safety glasses required for this tool. Face shield is optional but recommended. c) When cutting, the saw blade should project 1 4 above the stock or enough to clear the gullets. d) Stand to one side of the operation blade. Do not reach across it. Never stand behind or near anyone operating a table saw. e) Make sure that the stock is fully past the blade before turning the saw off.
13 Table Saw Safety f) The fence is used to guide ripping operations. The mitre gauge or sled is used to guide crosscut operations. Always hold the work firmly against the fence, sled, or miter gauge. NEVER use the fence and mitre gauge at the same time! g) During a rip cut, once the material has moved away from your left hand, move your left hand off the table. Do not drag your hand across the table and never reach over the blade. h) You must use a push stick when ripping pieces that are 6 or less in width. i) Cutting workpieces shorter than 10 in length is a special setup; get permission from the instructor or aide prior to cutting. j) Performing on-edge resawing is a special setup. You must get specific instruction and special permission from your instructor.
14 Table Saw Safety k) When ripping stock, the piece between the fence and blade must be controlled and pushed past the blade all the way onto the outfeed table. Failure to do so may result in a kickback. l) Lowering stock directly down over the saw blade (i.e. drop cut) is dangerous and is never allowed. m) Procedures involving raising the blade into the work are special setups. Permission and instructions must be obtained from your instructor for doing this type of work. n) The over-arm saw guard and riving knife must always be in place over the blade except when the instructor has authorized its removal for special setups. o) Make adjustments only when the power switch is off and the blade is at a complete stop.
15 Table Saw Safety p) Whenever a measurement or other procedure is made where you must have your fingers in close proximity to the blade, make sure the main power switch is in the off position. q) The main power switch should be left in the off position when you leave the saw. r) Freehand cutting, ripping, or crosscutting without using the fence, sled, or miter gauge is ABSOLUTELY FORBIDDEN in all circumstances. s) When you are ripping stock, the scrap must fall to the outside (non-bound side) of the blade (not between the blade and fence).
16 Table Saw Safety t) Do not reach over the saw blade or pass wood over the saw blade at any time. u) When helping someone to tail-off (supporting the work hanging off the back of the saw table), your only purpose is to support the stock from below. Only the operator pushes the stock through the saw. v) Make sure the blade is stopped and completely lowered when clearing scraps from the table. w) The instructor must inspect all special setups and dado blade installations before the power is turned on.
17 Table Saw Safety x) Use a special setup with V-block or sled when cutting cylindrical stock to help keep it from spinning. y) Backing the stock away from the blade while the saw is running may throw the piece toward you. If it is necessary to remove the piece, always stop the saw first. z) Never attempt to turn off the saw in the middle of a cut. If you must stop mid-cut, stop what you are doing without moving your hands and turn off the saw by gently engaging the red START/STOP PADDLE with your knee. aa) When you are crosscutting a number of pieces to the same length, clamp a clearance block to the rip fence well ahead of the saw blade to prevent the cut piece from being pinched between the blade and fence.
18 Table Saw Safety bb) Stock edges or faces that contact the table, miter gauge or fence, must be straight and flat. cc) Seek assistance and direction from your instructor before milling materials with defects such as splits, warps and knots. dd)changing the saw blade is required depending on the situation and is a special setup. The brake cartridge must be installed properly and adjusted approximately 1/8 away from the blade, and checked by the instructor. ee)obtain permission from the instructor for all special setups using the 8 dado set, which requires a different brake cartridge installed properly [1/8 gap]. Manually spin the blade through one rotation to make sure it clears the brake cartridge before turning on the saw.
Guild of Oregon Woodworkers Shop Safety Test
Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100% Make sure you put the answers under the correct portion of the answer sheet for the
More informationOSU Woodshop Safety Manual
OSU Woodshop Safety Manual The College of Forestry currently has two dedicated woodshops: the Oak Creek Woodshop (OCW) and the Kiln Bay Woodshop (KBW). No person may use OCW or KBW before completing the
More informationRevised 8/1/2018 Page 1
1Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100%. Make sure you put the answers under the correct portion of the answer sheet for the
More informationSAFETY INFORMATION PACKET
WILLOWCREEK MIDDLE SCHOOL SAFETY INFORMATION PACKET GENERAL SHOP SAFETY 1 WIDE BELT SANDER 2 BAND SAW 3 MITER SAW 4 UP- CUT SAW 4 PLANER 6 TABLE SAW 7 DRILL PRESS 8 LATHE 8 DISK / VERTICAL BELT SANDER
More informationHaley Hensley. Course: Structures. Unit Title: Woodworking. Materials: table saw, wood for cutting, safety glasses
Haley Hensley Course: Structures Unit Title: Woodworking Materials: table saw, wood for cutting, safety glasses I. Lesson Title a. Operation: Table Saw II. Situation a. Students are beginning the table
More informationStaying Safe at the Tablesaw
Staying Safe at the Tablesaw Prudent practices for ripping and crosscutting By Paul Anthony T he tablesaw doesn t enjoy a reputation as the safest tool in the shop. Truth is, it sends plenty of woodworkers
More informationAgricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
More informationMini Max 20 BAND SAW
OPERATING PROCEDURE FOR: Mini Max 20 BAND SAW SAFETY RULES: Warning: Willful violations of these safety rules, disruptive actions or horseplay may result in loss of the privilege to use the tools and machinery
More informationCopyright 2014 Curtis B. Vevang Page Number 1
As described on the Woodcraft Website: This is a 9 hour class consisting of 3, 3 hour sessions. The purpose of this class is to introduce woodworking from the ground up. The student will build a tool/garden
More informationJointer. Given a properly adjusted jointer, instruction and demonstration of use, each student will be able to:
Jointer I. Competencies Given a properly adjusted jointer, instruction and demonstration of use, each student will be able to: A. Identify the major parts of the jointer. B. Complete a written test on
More informationPOTENTIAL HEALTH & SAFETY HAZARDS
Number: OH&S 18.32.1 Revision Date: 03/12/2014 Radial Arm Saw Safety 1. PURPOSE 1.1. To provide operational guidelines on the safe use of Radial Arm Saws found in woodworking shops at Thompson Rivers University
More informationTable Saw Small Parts Sled Instructions
Table Saw Small Parts Sled Instructions Effective May 2018 Review full manual instructions prior to use for important safety information. Always check Rockler.com to confirm that you are using the most
More informationSan Diego Fine Woodworkers Association Member Shop Safety Test
You must pass the Test with an 80% or better and self-correct it to 100%. Make sure you put the answers under the correct portion of the answer sheet for the test you are taking. Use the Guild Safety Answer
More informationWhile one of the most
Plans NOW www.plansnow.com TOOLS & TECHNIQUES SERIES While one of the most useful tools for cutting joints is a dado blade, selecting which type to buy can be a little bit confusing. To simplify it, all
More informationCollege of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
More informationOPERATOR'S MANUAL 10 in. (254 mm) TABLE SAW BTS15
OPERATOR'S MANUAL 10 in. (254 mm) TABLE SAW BTS15 Your new Table Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared
More informationWOOD SHOP SAFETY. Rev. 2011
INTRODUCTION WOOD SHOP SAFETY Hand tools and power driven machine tools have been developed to save time and to do more accurate work. A hand tool or power tool is built to perform a specific operation.
More informationWays to get the most out of your
5 Ways to get the most out of your router table When you mount a router on a table, you expand your shop s potential. To help you take advantage of this potential, we assembled five router table techniques
More informationTech Ed Lab Safety SAFETY RULES Page 1-1
SAFETY RULES Safety Rules for Working with Wood 1. Secure your instructor s approval for all work you do in the shop. 2. Wear safety glasses when doing any operation that may endanger your eyes. 3. Always
More informationGeneral Shop Safety. Work Area. General Safety. First-Aid. Hand Tool Safety 10/18/2011. Personal Protective Equipment
Work Area General Shop Safety Eastview High School Technology & Engineering Department Keep work area clean Assure area is well lit Be aware of bystanders and surrounding area Properly secure and support
More informationMEMBER SHOP REFERENCE MANUAL
MEMBER SHOP REFERENCE MANUAL OF THE SAN DIEGO FINE WOODWORKERS ASSOCIATION 2018 Version 2.0 1 TABLE OF CONTENTS I. OVERVIEW --------------------------------------------3 1. GENERAL CAUSES OF ACCIDENTS
More informationMiter Fold Dado Set Instructions
Miter Fold Dado Set Instructions Effective April 2017 THIS PRODUCT IS INTENDED FOR EXPERIENCED WOODWORKERS ONLY; review full manual instructions prior to use for important safety information. Always check
More informationSurface planer or buzzer. Performs the tasks of dressing, squaring and straightening timber Machining short lengths of timber. Without the bridge guard. Without the appropriate training. Without PPE. Set
More informationIntroduction to Carpentry Power Tools
Youth Explore Trades Skills Introduction to Carpentry Power Tools Description s use power tools every day, and the ability to use these tools correctly and safely is paramount. In this Activity Plan, students
More informationHome Workshop System WARNING. MARK V Model 500. Summary Manual. Designed and Built in Dayton, Ohio.
Shopsmith Mark V Home Workshop System MARK V Model 500 Summary Manual Designed and Built in Dayton, Ohio. WARNING Read the SAFETY information in the Introduction section and complete the ASSEMBLY AND ALIGNMENT
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationINSTRUCTION MANUAL DW745-XE. HEAVY-DUTY 250 mm (10") COMPACT JOB SITE TABLE SAW
INSTRUCTION MANUAL DW745-XE HEAVY-DUTY 250 mm (10") COMPACT JOB SITE TABLE SAW TABLE OF CONTENTS General Safety Rules... 1 Double Insulation... 1 Electrical Safety... 1 Important Safety Instructions...
More information7th/8th Grade Industrial Tech General Safety. Give your undivided attention to the machine in which you are using.
7th/8th Grade Industrial Tech General Safety Wood Lab Safety General Safety Always wear safety glasses. Report all injuries to the instructor. No baggy clothing or open toed shoes. Give your undivided
More informationJET Heavy-Duty B3NCH 10" Jobsite Table Saw
JET Heavy-Duty B3NCH 10" Jobsite Table Saw The JET Heavy-Duty 10" Jobsite Table Saw brings many of the capabilities of a full-sized table saw to the jobsite, small or temporary woodworking shops. The unique
More informationOPERATOR S MANUAL 10 in. TABLE SAW BTS10
OPERATOR S MANUAL 10 in. TABLE SAW BTS10 Your table saw has been engineered and manufactured to Ryobi s high standard for dependability, ease of operation, and operator safety. When properly cared for,
More informationINDEX. General Shop safety Rules. Preventing Accidents. Rules for operating Equipment. Table Saw. Avoiding Kickback. Jointer.
General Shop safety Rules Preventing Accidents Rules for operating Equipment Table Saw Avoiding Kickback Jointer Thickness Planer Radial Arm-Saw Compound Mitre Saw Bandsaw Drill Press Router Table Belt/Disc
More informationOPERATOR'S MANUAL 10 in. (254 mm) TABLE SAW BT3100-1
OPERATOR'S MANUAL 10 in. (254 mm) TABLE SAW BT3100-1 Your new Table Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly
More informationOPERATOR S MANUAL 10 in. TABLE SAW RTS10/RTS10G
OPERATOR S MANUAL 10 in. TABLE SAW RTS10/RTS10G Your table saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for,
More informationOPERATOR'S MANUAL ROUTER MOUNTING KIT
OPERATOR'S MANUAL MOUNTING KIT 4950301 (FOR USE WITH BT3000 AND BT3100 TABLE SAWS) Your new router mounting kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More informationPCX IN PORTABLE TABLE SAW. Instruction Manual. Français (#) Español (#)
10-IN PORTABLE TABLE SAW Français (#) Español (#) www.portercable.com Instruction Manual PCX362010 To reduce the risk of serious injury, thoroughly read and comply with all warnings and instructions in
More informationQuestions? Visit us at Des questions? Rendez nous visite à Tiene preguntas? Visítenos en
Before returning this product call 1-800-4-DEWALT IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE, CALL 1-800-4-DEWALT IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER
More informationComox Wood Hobby Club. Shop Safety and Operating Instructions
Comox Wood Hobby Club Shop Safety and Operating Instructions Updated: 01 Apr 2013 Table of Contents Foreword...3 1. SHOP SAFETY - General Instructions...4 2. Personal Equipment...4 3. Clothing...4 4. Fire
More informationWOODWORKING MACHINERY GUARDING
APPENDIX E WOODWORKING MACHINERY GUARDING The following requirements are restated from 29 CFR 1910.213, Woodworking machinery requirements. (a) Machine construction general. (1) Each machine shall be so
More informationOWNER S MANUAL 10 CABINET SAW. Models CB31230, CB33230, CB51230,CB53230, CB53480
OWNER S MANUAL 10 CABINET SAW Models CB31230, CB33230, CB51230,CB53230, CB53480 Copyright 2004, SawStop, LLC Patents Pending All Rights Reserved. 1st printing, December 2004 Updates of this manual may
More informationEssential BOX JOINT JIG
Essential BOX JOINT JIG Home in on precise finger joints with this table saw sled. By Ken Burton The box (or finger) joint is a remarkably strong, interlocking corner joint that can be quickly made on
More informationAssembly Instructions
Assembly Instructions 10 CONTRACTOR TABLE SAW Model No. 351.218330 Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 31624.00 Draft (10/08/09) UNPACKING The
More informationSquaring Up Rough lumber BY JOE HURST-WAJSZCZUK
LESSONS FROM A PRO Squaring Up Rough lumber BY JOE HURST-WAJSZCZUK Straight, flat, square boards aren t born that way. master this step-by-step sequence to make any stock shop-ready. 58 w o o d c r a f
More informationTo reduce the risk of injury, the user must read and understand the operator s manual before using this product.
OPERATOR S MANUAL 10 in. TABLE SAW R4513 Your table saw has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, it
More informationTongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com
Tongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com A tongue and groove cabinet door is made up of at least 5 pieces. Two horizontal rails (blue), two vertical styles (green), and one
More informationTable of Contents Responsibilities... 3 Department Head & Supervisors... 3 Employees & Student Laborers... 3 Machine Guarding Definitions 29 CFR
Machine Guarding Table of Contents Responsibilities... 3 Department Head & Supervisors... 3 Employees & Student Laborers... 3 Machine Guarding Definitions 29 CFR 1910.211... 4 General requirements for
More informationWARNING. Table Saws Are Very Dangerous. Component Descriptions
27. Ground all tools. Make sure wiring codes and recommended electrical connections are followed and that tool is properly grounded. 28. Outdoor use extension cords. When tool is used outdoors, use only
More informationModel W1837 (For Machines Mfd. Since 8/18) PARTS. Main PARTS -83-
-83- Main 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 113 96 90 91 92 93 95 96 97 98 100 101 102 103 104 105 106 109
More informationOperator s Manual. 10 CONTRACTOR TABLE SAW Model No Safety Unpacking Assembly Operation Maintenance Parts List Español
Operator s Manual 10 CONTRACTOR TABLE SAW Model No. 351.218330 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Keep this Manual with Tool. Sears Brands
More informationYale Practices for Tool Safeguarding and Controls 1
Arbor Press Manual Caught between crushing, limited by manual operation Band Saw / Small Bench Cutting blade lacerations Rotating blade pulleys pinch points, entanglement for wood Band Saw / Large Cutting
More informationZeroPlay Guide Bar Jig Plans (V2.0) Micro Jig, Inc. PO Box Winter Springs, FL USA
Z2 ZeroPlay Guide Bar Jig Plans (V2.0) 0409 Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719 USA Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2009 Micro Jig,
More informationPRATT INSTITUTE SHOP ORIENTATION MANUAL
PRATT INSTITUTE SHOP ORIENTATION MANUAL This booklet is a reference guide and supplement to the shop orientation classes. Study of this booklet does not qualify any student to use Pratt Shops. TABLE OF
More informationKANSAS CITY WOODWORKERS GUILD SHOP RULES & GUIDELINES
KANSAS CITY WOODWORKERS GUILD SHOP RULES & GUIDELINES 1. The Director of Assets is responsible for overall coordination of the Shop and has the authority to stop activities not believed to be consistent
More informationModel D1700/D1701 Moulding Head Instruction Sheet
Model D1700/D1701 Moulding Head Instruction Sheet Phone #: (360) 734-3482 Online Tech Support: tech-support@shopfox.biz Web: www.shopfox.biz To reduce risk of serious personal injury when using moulding
More informationHybrid Table Saw Owner s Manual
10040 10 Hybrid Table Saw Owner s Manual Oliver Machinery M-10040 032019 Seattle, WA Copyright 2003-2019 info@olivermachinery.net www.olivermachinery.net Table of contents READ CAREFULLY BEFORE OPERATING
More informationPRO System with Dedicated Automatic Kerf Keeper Installation Manual - SP-2 (V1.0) 0706
SP2 Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719, USA. Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2006 Micro Jig, Inc. MJ Splitter PRO System with Dedicated
More informationOperator s Manual. 10 IN. JOBSITE TABLE SAW Model No CAUTION: Safety Instructions Installation Operation Maintenance Parts List
Operator s Manual 0 IN. JOBSITE TABLE SAW Model No. 37.4500 CAUTION: Before using this Table Saw, read this manual and follow all its Safety Rules and Operating Instructions Customer Help Line For Technical
More informationSYSTEM OWNER S MANUAL
From the makers of INCRA JIG SYSTEM OWNER S MANUAL W hat does an INCRA tool do better than any other? Just ask that question to any of the thousands of satisfied INCRA router table or table saw fence owners
More informationTABLE SAW WITH HEAVY-DUTY STEEL STAND
model no. 055-755-8 TABLE SAW WITH HEAVY-DUTY STEEL STAND IMPORTANT: Please read this manual carefully before using this table saw and save it for reference. INSTRUCTION MANUAL TABLE OF CONTENTS Quick
More informationRight-Angle Sled. Owner s Manual 05J U.S. Patent No. 5,890,524
Right-Angle Sled Owner s Manual 05J24.01 U.S. Patent No. 5,890,524 Introduction The Veritas Right-Angle Sled straddles the Veritas Router Fence, giving rock solid support to the right-angle arm. As with
More informationWestern Illinois University Department of Art Woodshop Orientation
Western Illinois University Department of Art Woodshop Orientation SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
More informationSECTION 10: PARTS. Main Model G0771Z (Mfd. Since 09/16)
SECTION 10: PARTS Main 96 103 105 119 104 120 102 101 124 29-1 29-4 29-2 29-5 29-3 29-6 29-7 29-8 29-9 29-10 97 98 99 121 100 106 97 98 99 100 121 96 29 27 28 125 24 25 26 30 53 41 40 39 31 34 114 115
More informationTable Saw INSTRUCTION MANUAL. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
INSTRUCTION MANUAL Table Saw 705 DOUBLE INSULATION For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. ENGLISH SPECIFICATIONS Riving knife-related
More informationOPERATOR'S MANUAL RULES FOR SAFE OPERATION
OPERATOR'S MANUAL #4950300 ROUTER AND JIG SAW MOUNTING KIT (FOR USE WITH THE BT3000 TABLE SAW) CONGRATULATIONS AND THANK YOU FOR BUYING THIS RYOBI ROUTER AND JIG SAW MOUNTING KIT. Your new #4950300 Router
More information10 IN. (254 mm) JOBSITE TABLE SAW. sierra de mesa de 254 mm. Instruction Manual Manuel d instructions Manual de instrucciones.
0 IN. (5 mm) JOBSITE TABLE SAW scie circulaire de 5 mm (0 po) sur le lieu de travail sierra de mesa de 5 mm (0 pulg.) para la obra Instruction Manual Manuel d instructions Manual de instrucciones www.portercable.com
More informationPRATT. industrial design department SHOP SAFETY MANUAL
PRATT industrial design department SHOP SAFETY MANUAL This booklet is intended as a reference guide and supplement to the shop certifi cation classes. Study of this booklet does not qualify any student
More informationOperating Instructions and Parts Manual 10" Job Site Table Saw Benchtop Series Model No. JBTS-10MJS
Operating Instructions and Parts Manual 10" Job Site Table Saw Benchtop Series Model No. JBTS-10MJS For models with serial no. 12120886 and higher JET 427 New Sanford Road LaVergne, Tennessee 37086 Part
More informationIF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF DE USAR EL PRODUCTO.
Before returning this product call 1-800-4-DEWALT IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE, call 1-800-4-DEWALT IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER
More informationI I. . i1 AD JUSTABLE SHELVES
ADJUSTABLE SHELVES HAD BEEN TRYNG TO WORK out a really simple (read "fast") way to make an elegant wooden version of the old standby, metal standards and brackets. Although have seen many commercial versions
More informationINSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF
Before returning this product call 1-800-4-DEWALT IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR DEWALT PURCHASE, call 1-800-4-DEWALT IN MOST CASES, A DEWALT REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER
More informationOperating Instructions and Parts Manual 10" Job Site Table Saw Benchtop Series Model No. JBTS-10MJS
Operating Instructions and Parts Manual 10" Job Site Table Saw Benchtop Series Model No. JBTS-10MJS R C US 174315 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No.
More informationHow To Buy A Table Saw A Roadmap Of Today s Table Saw Market. By David Munkittrick Photos by: Manufacturers
How To Buy A Table Saw A Roadmap Of Today s Table Saw Market By David Munkittrick Photos by: Manufacturers Introduction Most woodworking shops, from modest garage shops to fully equipped pro shops, are
More informationWESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART
WESTERN ILLINOIS UNIVERSITY DEPARTMENT OF ART WOODSHOP ORIENTATION SAFETY is the first priority woodworking tools are inherently dangerous. Machines turn sharp saw blades and cutters at high speeds. Accidents
More informationCongratulations on your purchase of the Divided Light Door Set. This set will help you create beautiful cabinet doors with true divided light panels.
Divided Light Door Set User Instructions Congratulations on your purchase of the Divided Light Door Set. This set will help you create beautiful cabinet doors with true divided light panels. Following
More informationServing Tray. When some good friends got married recently, An exercise in template-making yields a great gift project that s easy to duplicate
Serving Tray An exercise in template-making yields a great gift project that s easy to duplicate END Create from 3 8 2 8" piece. By Geoff Noden When some good friends got married recently, I decided to
More information(a) Machine Construction General (a) 4/5/2016
1910.213 WOODWORKING MACHINERY REQUIREMENTS 1910.213(a) Machine Construction General Machines shall be constructed to be free from vibration when largest tool is mounted and run at full speed 1910.213(a)
More informationGeneral Wood Shop Notes
General Wood Shop Notes Restricted Materials No METAL or BONE of any kind on any machine or in the room o See additional restrictions individual machine All reclaimed and other than new lumber must be
More informationWoodline USA Woodline Spacer Fence System
Woodline USA Woodline Spacer Fence System MADE IN THE USA Includes: (1) ¼ Spacer Fence (1) 3/8 Spacer Fence (1) ½ Spacer Fence (1) Hardware Package (1) 3 Piece Brass bar set (2) Setup Blocks Visit Us Online
More informationCOLLEGE OF DESIGN WORKSHOP General Shop Procedure & Policy *** READ COMPLETELY ***
COLLEGE OF DESIGN WORKSHOP General Shop Procedure & Policy *** READ COMPLETELY *** Shop access is a privilege binding on full compliance with Procedure, Policies and Limitations as described below and
More informationDovetail Saw Guides. Figure 1: Dovetail saw guide, exploded view. Guide Block. UHMW Friction Pad. Sliding Clamp. Rare-Earth Magnet
Dovetail Saw Guides U.S. Pat. No. 6,607,016 Dovetail joints have traditionally been the hallmark of a cabinetmaker who had acquired an expert level of skill. They are also a mark of quality and attention
More informationButterfly Leaf Dining Table Plans
Butterfly Leaf Dining Table Plans Part 1 An attractive dining table with a secret: the leaf folds and stores inside the table. Season 1, Episode 7 P a g e 2 I first saw a butterfly leaf table in a back
More informationTS4001. Model # 10 inch Table Saw addendum SETUP & OPERATION MANUAL
SETUP & OPERATION MANUAL Features Powerful 13 amp motor Cast aluminum work table Riving knife Anti-kickback pawls Includes: 10 in. 24 tooth tungsten carbide tipped saw blade Rip fence Miter gauge Push
More informationMAKER LAB Safety Instructions Power Tool Training
MAKER LAB Safety Instructions Power Tool Training Note: All the instructions from Basic Training apply to Power Tool Training. If you have not completed Basic Training, do so before you complete Power
More informationJointer Quick Start Guide
Jointer Quick Start Guide This jointer runs on 220V (208V really because, 3 phase power). Don t joint anything that might have metal in it, like nails or screws. Any metal that hits the blades ruins them.
More informationowner s manual 10-INCH RADIAL SAW GUARD KIT FOR YOUR SAFETY: assembly operating repair parts MODEL NO
Save This Manual For Future Reference owner s manual MODEL NO. 509398 509399 509398 FITS THE FOLLOWING RADIAL SAWS: 113.197120, 113.197190, 113.197160, 113.197240, 113.197110, 113.197111, 113.197150, 113.197151,
More informationRouter Table. In a recent article, I wrote about the router table I built for the Center. 5 Essential Jigs for the
5 Essential Jigs for the Router Table Great fixtures and fences offer better control and new possibilities BY PETER SCHLEBECKER In a recent article, I wrote about the router table I built for the Center
More informationBOWLING GREEN STATE UNIVERSITY SCHOOL OF ART WOODSHOP MANUAL
BOWLING GREEN STATE UNIVERSITY SCHOOL OF ART WOODSHOP MANUAL WRITTEN BY: CLAYTON PETERSON HANS RUEBEL LEONARD TAYLOR 1 1. GENERAL REFERENCE...5 1.1 Introduction... 5 1.2 Machine vs. Hand... 5 1.3 Rip-cuts...
More informationSingle MJ Splitter Installation Manual - 1Si
SP1 Single MJ Splitter Installation Manual - 1Si Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719, USA. Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2004 Micro
More informationWoodworking Tools. Radial Arm Saws. Teacher s Guide
Woodworking Tools Radial Arm Saws Teacher s Guide Introduction This Teacher s Guide provides information to help you get the most out of Radial Arm Saws, part of the Woodworking Tools series. The contents
More informationOperating Instructions and Parts Manual 10-inch Table Saw
Operating Instructions and Parts Manual 10-inch Table Saw Model 66 shown with optional extension table and legs, mobile base, and motor cover WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part
More informationInstructions and Parts Manual 10-inch Cabinet Saw Model PM2000
Instructions and Parts Manual 10-inch Cabinet Saw Model PM2000 Model PM2000 Table Saw shown with optional extension table and legs Powermatic 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-1791997AU
More information10 IN. (254 MM) STATIONARY TABLE SAW BANC DE SCIE 254 MM (10 PO) SIERRA DE MESA 254 MM (10 PULG.)
0 IN. (5 MM) STATIONARY TABLE SAW BANC DE SCIE 5 MM (0 PO) SIERRA DE MESA 5 MM (0 PULG.) Instruction Manual Manuel d instructions Manual de instrucciones www.portercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS
More informationOperating Instructions and Parts Manual Table Saw Model: JWTS-10JF
This Manual is Bookmarked Operating Instructions and Parts Manual Table Saw Model: JWTS-10JF JWTS-10JF Table Saw shown with optional Mobile Base Stand WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois
More informationAdvanced Woods-CA-TS-v1.0 (Radial Arm Saw Safety Test) Preview Student Page 1 of 2 Preview Teacher Printed: 2/10/2014 Preview Course 211.
Advanced Woods-CA-TS-v1.0 (Radial Arm Saw Safety Test) Preview Student Page 1 of 2 Preview Course 211.1719 NAME: DATE: RADIAL ARM SAW SAFETY TEST Multiple Choice You may have to select more than one correct
More informationR Double Insulated
OPERATOR S MANUAL 12 in. COMPOUND MITER SAW WITH LASER R4120 - Double Insulated Your miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
More informationWoodworking Glossary
Abrasives Any substance such as aluminum oxide, silicon carbide, garnet, emery, flint or similar materials that is used to abrade or sand wood, steel or other materials. Substances such as India, Arkansas,
More informationHUMAN FACTORS EVALUATION OF TECHNOLOGY INTENDED TO ADDRESS BLADE-CONTACT INJURIES
HUMAN FACTORS EVALUATION OF TECHNOLOGY INTENDED TO ADDRESS BLADE-CONTACT INJURIES WITH TABLE SAWS JULY 2011 Timothy P. Smith Engineering Psychologist Division of Human Factors Directorate for Engineering
More informationThe Universal Table Saw Sled
The Universal Table Saw Sled Do Precision Work Even with Inexpensive Table Saws! Table saw blades always tend to move the wood while the cut is being made. This is why it's so difficult to get accurate
More informationWoodstock Technical Support... 2 Controls and Features... 3 Model W1819 Specifications... 4 Model W1820 Specifications... 7
232857 Woodstock Technical Support... 2 Controls and Features... 3 Model W1819 Specifications... 4 Model W1820 Specifications... 7 Standard Machinery Safety... 10 Additional Safety for Table Saws... 12
More informationSECTION 10: PARTS G1023RL
SECTION 10: PARTS 131 132 133 G1023RL (All) Main 121 118 119 128 126 125 124 123 124 122 120 119 128 116 6V2 5 4V2 4-1 129 127 128 117 26V3 26-3V2 26-1 6-2 (G1023RLWX) 26-2 26-4V3 7 6-1 1 (G1023RL) 19-1
More information