HAMPTON ACACIA COFFEE TABLE ASSEMBLY INSTRUCTIONS

Transcription

1 Thank you for purchasing the AMPTON AAIA OEE TABLE Please read the instructions carefully to ensure safe operation of the product. Size:X5X3M olour:aaia PLEASE REA this sheet prior to assembly to familiarise yourself with the various stages of construction. arefully open the pack supplied and check the contents against the parts and fittings check list.o not destroy any of the packaging until you are certain that you have all the necessary parts for the assembly. AUTION: There are small components used in the construction of this unit. These loose items should be kept away from young children whilst assembling your unit to avoid the danger of choking hazards. Tools Required X Page of

2 IMPORTANT - REA AREULLY - RETAIN TESE INSTRUTIONS OR UTURE REERENE. INORMATION This product is intended for a maximum weight of 50 kg. o not exceed this weight. ue to the size of this product we recommend that it is assembled in the room intended for use. When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for assembly. Unwrap all packaging materials and place the components on top of the carton box or on a clean floor to prevent it from scratching. heck the pack and make sure you have all the parts listed. Ensure that this product is fully assembled as illustrated before use. heck all screws or bolts are tightened and inspect regularly This product should only be used on firm,level ground. Keep small parts out of reach of children. Make sure the legs remain in contact with the ground. Tools not included. WARNINGS O NOT use power tools to construct this product. O NOT tighten screws until fully assembled. O NOT over tighten screws or bolts. O NOT use this product if parts are missing, damaged or worn. O NOT sit or stand on the product. ARE INORMATION Never use scourers, abrasives or chemical cleaners. To clean wipe with a sponge and warm soapy water. o not use solvent based cleaners or detergents as they can bleach or damage the product. Page of

3 Please check the pack contents before assembling the product. If any components are missing, please contact your retailer. The fittings pack contains small items that should be kept away from small children Page 3 of

4 PARTS 3 escription: LET AN SIE PANEL escription:rigt AN SIE PANEL escription: TOP PANEL 5 escription: BOTTOM PANEL escription: MILE BOTTOM ROSS BAR escription: RONT/BAK BOTTOM Qty:PS 7 ROSS BAR escription: RAWER RONT escription: RAWER RIGT AN SIE escription:rawer LET AN SIE Qty:PS Qty:PS (LET SIE) PANEL PANEL escription: RAWER MILE Qty:PS escription: BOTTOM TRIM PANEL (BAK SIE) 3 escription: RAWER BOTTOM escription: RAWER RONT Qty:PS escription: RAWER BAK (RIGT SIE) Page of

5 ITTINGS(to scale) imensions Qty A AM BOLT 7X5mm B AM BOLT 7X3mm 7 AM NUT Xmm 33 G BOLT OWEL X30mm E SREW( 5X0mm) SREW( 3.5Xmm) Ref Xmm (Not to scale) RUNNER 300mm I ANLE K ENTRE OOT Z OOT AUTION: There are many small components used in the construction of this product. Please keep these components away from young children whilst assembling this product. If you keep the fittings in a bowl during assembly you will be less likely to lose them! Page 5 of

6 ints and Tips on t screw too deep Layout Parts on Soft Surface Lay out all parts on a soft surface i.e. Rug,arpet or Packaging arton Page of

7 STEP. LET AN SIE PANEL X. RIGT AN SIE PANEL X. RAWER MILE X. SREW X. RUNNER X Z. OOT X Z STEP. BOTTOM TRIM PANEL (BAK SIE) X. RAWER MILE X. AM NUT X B. AM BOLT X. OWEL X B on t screw too deep Page 7 of

8 STEP 3. BOTTOM PANEL X. RONT/BAK BOTTOM ROSS BAR X. AM NUT X B. AM BOLT X. OWEL X E. SREW X B E E on t screw too deep STEP 5. MILE BOTTOM ROSS BAR X. AM NUT X 3 B. AM BOLT X. OWEL X K. ENTRE OOTX B K 5 on t screw too deep Page of

9 STEP 5 A. LET AN SIE PANEL X. RIGT AN SIE PANEL X A. AM BOLT X. AM NUT X. OWEL X 5 A on t screw too deep STEP 3. TOP PANEL X A A. AM BOLT X. AM NUT X 3. OWEL X 3 A on t screw too deep Page of

10 STEP 7 G 3 E I B 7. RAWER RONT (LET SIE) X. RAWER RIGT AN SIE PANEL X. RAWER LET AN SIE PANEL X. RAWER BAK X 3. RAWER BOTTOM X. RAWER RONT (RIGT SIE) X B. AM BOLT X. AM NUT X E. SREW X. SREW X G. BOLT X. RUNNER X I. ANLE X 7 7 G E 3 I B on t screw too deep Page of

11 OMPLETE ASSEMBLY Your AMPTON AAIA OEE TABLE is now completely assembled. Periodically check to ensure that the components are in their proper position, free from damage. Also, make sure the connectors are tight and secure. Keep instructions for future reference Page of