Newark 8 Piece Budget Dining Set Assembly Instructions. Product size: Table: Dia.110xH72cm Chair: W60xD62xH88cm Umbrella: dia.3m

Transcription

1 Product size: Table: Dia.110xH72cm Chair: W60xD62xH88cm Umbrella: dia.3m MPORTANT, RETAN FOR FUTURE REFERENCE READ CAREFULLY 1/8

2 Warnings Before you start Dos MPORTANT, RETAN FOR FUTURE REFERENCE READ CAREFULLY See enclosed instructions for assembly, safety and care information Failure to follow the warnings could result in serious injury. Handle heavy parts with care. Ensure that this product is fully assembled as illustrated before use. This product should only be used on firm, level ground. Keep small parts out of reach of children. Do not stand or climb onto this product. This product is intended for domestic use only. Furniture can be dangerous if incorrectly used. No liability will be accepted for damage or injury caused by incorrect use of this product. Dos When you are ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for assembly. Remove all packaging and banding and place the components carefully on suitable surfaces to prevent damaging or scratching them. Check the pack and make sure you have all of the parts listed. Check all screws and bolts are tightened and inspect regularly. Do not use scourer, abrasives, washing powders, chemical cleaners or any other substances containing abrasives since these substances can damage the product, including the glass panel. Never tilt the chair or table during use. Do not place very hot or very cold items on the glass surface unless adequately thick table-mats are used to prevent such items from coming into contact with the glass. Do not use the glass as a chopping surface. Do not strike glass with hard or pointed items. Do not strike the glass with hard or pointed items. Do not use power tools to construct this product. Do not use this product if parts are missing, damaged or worn. Do not sit or lean on the table. Do not stand or climb onto the product and do not use it as a ladder, as this could lead to it unbalancing and overturning. Never drag furniture when moving it, always lift it. Number of people required for assembly. Two people Time to assemble We recommend the use of furniture covers to protect your product when not in use. This product is suitable for all year outdoor use. Cushions should not be left out in wet weather or overnight. PLEASE NOTE all cushions should always be stored indoors after use. THE CUSHONS ARE NOT WATERPROOF. We recommended the use of furniture covers to protect your furniture when not in use. During severe weather conditions, please move your furniture inside. To prolong the life of the product we recommend that during severely bad weather and during the winter months, it is stored in a cool, dry place. Before storage, ensure that the product is clean and dry. To clean, wipe down with a sponge and warm soapy water and wipe with a clean, dry cloth. Cushions should be cleaned following the care instruction on the label. Tools required 80 minutes Tips: Do Not fully tighten bolts before all components are connected. Only fully tighten once you are satisfied with the alignment of all components. Do not overtighten bolts. 2/8

3 Components fixtures & fittings not actual size Parts List Part No. Diagram Qty Part No. Diagram Qty A G1 B 2 PCS G2 C 2 PCS H M6x15mm 4 PCS D M6x32mm 68 PCS E 72 PCS M6 F K 3/8

4 Components fixtures & fittings not actual size Parts List Part No. Diagram Qty Part No. Diagram Qty L N M 4/8

5 Note: All Bolt Head Caps and Nut Caps should not be attached before finally tightening all Bolts with the Allen Key. Only tighten all bolts when you are satisfied with the alignment of all components. How to... assemble the table Step One Put the table top (Part A) on the ground. Connect the table leg part (Part C) with the table top part (Part A), fasten them together by bolts (Part H) and washers (Part ). H C A Step Two Connect another table leg part (Part C) with the table top part, fasten them together by bolts (Part H) and washers (Part ). H C Step Three Connect the table side part (Part B) with the leg part, fasten them together by bolts (Part ) and washers (Part ). B B PLEASE KEEP THESE NSTRUCTONS FOR FUTURE REFERENCE. 5/8

6 Step Four Put the table glass (Part D) on the table top. D How to... assemble the chairs Step One Connect the chair seat part (Part F) with the chair left armrest part (Part G1). Fasten them togehter by bolts (Part ) and washers (Part ). G1 F Step Two Fasten the chair right armrest part (Part G2) with the chair seat part (Part F) by bolts (Part ) and washers (Part ). G2 PLEASE KEEP THESE NSTRUCTONS FOR FUTURE REFERENCE. 6/8

7 Step Three Fasten the chair back part (Part E) with the armrest part by bolts (Part ) and washers (Part ). E Step Four Put the chair seat cushion (Part K) on the seat part. K How to... assemble the umbrella Step One Connect the umbrella lower pole (Part M) with the upper pole (Part L). L M PLEASE KEEP THESE NSTRUCTONS FOR FUTURE REFERENCE. 7/8

8 Step Two Rotate the crank to open the umbrella. Step Three Put the umbrella into the table umbrella hole. Push the button could make the umbrella tilt. PLEASE KEEP THESE NSTRUCTONS FOR FUTURE REFERENCE. 8/8