Tryed Side Table Published on Ana White (

Transcription

1 Tryed Side Table [1] Submitted by Ana White [2] on Tue, :00 [1] Summary: Following numerous requests, here are plans for the Hyde Side Table. This plan matches the plans for the Tryde Coffee Table and the Tryde Console Table. Made of solid wood in a rustic planked design, you will be shocked at just how beautiful 2x4s can be. This sturdy easy to build end table will add character and a natural aspect to your living space. Also can be used as a nightstand. Features sturdy solid wood legs and a large top with breadboard ends. Page 1 of 10

2 CategoriesProject Type: Accent Table Plans [3] Side and End Table Plans [4] Room: living room [5] Collections: Tryed Rustic Accent Table Collection [6] Skill Level: Beginner [7] Style: Farmhouse Style Furniture Plans [8] Estimated Cost: Under $20 [9] Dimensions: 21"x21"x24" Dimensions: Post, 8 feet long 1 1 4, 8 feet long 2 2 4, stud length or 8 feet long Common Materials: 2 1/2 inch screws 2-1/2" Pocket Hole Screws [10] Elmer's Wood Glue [11] Elmer's Wood Filler [12] 120 grit sandpaper primer wood conditioner paint paint brush Tools: Page 2 of 10

3 [13] Page 3 of 10

4 [14] [15] [16] Cut List: A) /2 (Legs) B) /4 (Spacers) C) /2 (Top Leg Supports) D) (Apron) E) (Breadboard Ends) F) (Tabletop Pieces) General Instructions: Cut all your boards, except you may wish to cut the tabletop boards after taking an exact measurment of your table in step 7. Make sure you get nice straight cuts. Either use a miter saw, chop saw, or mark your boards with a square and cut with a handheld saw. Predrill all of your screw holes with a countersink bit. Before attaching any boards, mark where the attaching board will fit. Always use glue. Use 2 1/2 screws unless otherwise directed. Take a square of the project after each step (see HOW-TO section). Work on a clean level surface. Step 1 Page 4 of 10

5 [17] 1. Spacers. Fasten the spacers to the legs, as shown above. Notice how the spacers will all be placed in different positions depending on the leg postion. Take note of this as you fasten the spacers to the legs. Step 2 [18] Page 5 of 10

6 2. Top Leg Support. Attach the top leg support as shown above. Use the meausrements to guide you. Also make sure you screw into the spacer and the legs. Step 3 [19] 3. Aprons. Attach the side aprons as shown above in green. Keep top edges flush. Step 4 Page 6 of 10

7 [20] 4. Aprons. Attach the remaining aprons as shown above. Keep top edges flush. Step 5 [21] Page 7 of 10

8 5. Breadboard Ends. Screw the breadboard ends in place. Use 4 screws to screw into the legs. Step 6 [22] 6. Tabletop Pieces. Attach the tabletop pieces as shown above. Keep the gaps between the boards minimal. If you are having a problem with the gaps, add a tabletop support piece as done in the Hyde Console Table, step 5, and attach the tabletop pieces from underneath. Step 7 Page 8 of 10

9 [23] 7. Toenailing. Make sure you secure the ends of the tabletop pieces to the breadboard ends as shown above. Screw at an angle from the tabletop pieces into the breadboard ends. Source URL: Links [1] [2] [3] t-tables [4] ables [5] [6] ustic-accent-table-collection [7] [8] Page 9 of 10

10 [9] der-20 [10] TF8&camp=1789&creative=390957&creativeASIN=B00 0BN7DLU&linkCode=as2&tag=knooffwoo-20&linkId=XL DYGROR7GI4SHLA [11] [12] struction# [13] [14] [15] [16] [17] yde_side_table_4.jpg [18] yde_side_table_5.jpg [19] yde_side_table_6.jpg [20] yde_side_table_7.jpg [21] yde_side_table_10.jpg [22] yde_side_table_8.jpg [23] yde_side_table_9.jpg Page 10 of 10