Architectural Hardware Products

Transcription

1 rchitectural Hardware Products

2 Table of ontents page Terms and onditions ii-iii Index by Product escription iv Index by Part Number v inish hart vi-vii Packaging, Handing viii - Hinges and Pivots rchitectural Hinges Residential Hinges ontinuous Hinges Pivots Pocket Pivot/Hinges Pulls and Push Plates Pulls Push ars Vandal Resistant Trim Protection Plates Mounting etail lush olts oordinators Surface olts oor uards Roller Latches ngle Latches/atches loor loor & Holders Wall umpers/ Wall Holders Kick own Holders Plunger oor Holders Roller umpers Residential oor Hinge Pin Silencers xterior Hardware Lock uards oor Viewers oor Knockers Letter ox/plates oor Numbers Storm oor Latch Screen oor Pull rash Hooks & rackets Window Hardware Hobby Hardware abinet/loset Hardware xterior Hardware i

3 Terms and onditions xterior Hardware ii INRSOLL-RN OMPNY, SURITY THNOLOIS STOR, NRL TRMS N ONITIONS O SL N SRVI 1. NRL. (a) This greement contains the terms and conditions by which ompany will quote and sell its Products and Services to ustomer. (b) The terms purchase order or order for the purposes of this greement include the term request for quotation, as appropriate. (c) This greement supersedes all pre-printed and boilerplate terms and conditions set forth in any purchase order issued by ustomer. (d) No reference herein to ustomer s purchase order will in any way incorporate different or additional terms and which conditions are hereby objected to. (e) NY PTN Y OMPNY O USTOMR S PURHS ORR IS XPRSSLY ONITION ON TH USTOMR S SSNT TO N PTN O TH TRMS N ONITIONS ONTIN IN THIS RMNT. (f) In the event of a conflict between this greement and a purchase order issued by ustomer, the terms of this greement will prevail. In the event of a conflict between this greement and any specific Product or Service terms and conditions, the specific Product or Service terms and conditions will prevail. 2. SOP O PROUTS N SRVIS N ORRS. (a) Scope of Products and Services. The scope of the Products and Services (including, but not limited to location) are (i) attached to this greement, (ii) separately furnished by ompany to ustomer, or (iii) subject to Section 1 herein, contained in an order submitted by ustomer. Non-standard finishes and special items may be available. ontact ompany for such availability. ll Products that come in kits cannot be sold as individual pieces. See the specific product terms and conditions for exceptions. (b) Orders.ll orders submitted by ustomer must be in written form acceptable to ompany. (c) Receipt of an Order. ompany will acknowledge receipt of each order issued in accordance with this greement and will notify ustomer whether such order has been accepted or rejected, in whole or in part, by ompany. If ompany fails to acknowledge receipt of an order, within a reasonable time period, such failure to acknowledge receipt will be deemed a rejection of the entire order. (d) hanges to Orders or ancellation of Orders. hange order request and ancellations can be by phone, fax, or . hanges and ancellations are allowed without penalty if made within 48 hours of order receipt if the order has not shipped. Some exceptions do apply - please consult the factory. fter 48 hours, all changes or cancellations are subject to a charge of 25% of the net product or service value plus the cost of any fabrication or raw materials that have been purchased for the order. Unless otherwise specified by ompany in writing, any changes to orders acknowledged by ompany that affect the delivery date will be deemed a new order and will require acknowledgement by ompany as provided in this Section PRIS N PYMNT.(a) Prices.The prices specified by ompany are subject to change, without notice, to ompany s prices in effect at the time of each shipment of Products or performance of Services. dditional charges may be applied for product modification or engineering services. Oral prices specified by ompany are null and void. (b) Invoices. ompany will submit invoices to ustomer stating amounts due. (c) Payment Terms.Payment terms are 2% cash discount 20 days, net 35 days from date of invoice. Payment will be made in United States dollars. (d) redit Terms. ll orders are subject to ompany s credit limit and terms of credit required by ompany or contained in ompany s credit application, which is subject to change by ompany at any time either before or after delivery of any part of the order. ompany reserves the right to request payment in advance of shipment or any order or to request adequate assurances for ustomer s payment of an order and may withhold or stop shipment, without any liability to ompany, until ustomer submits payment or assurance of payment, as required by ompany. (e) efault. If ustomer is in default in payment or otherwise with respect to any order for Products or Services or any other contract with ompany, ompany shall have the right, in addition to all other legal remedies and without prejudice to any of its right hereunder, to defer further shipments until such default is corrected and to declare all outstanding bills of ustomer to be immediately due and payable. (f) Taxes.ny taxes, charges, or duties imposed by any governmental authority on the sale of Products or Services will be paid by ustomer, in addition to the selling price specified by ompany. (g) Late Payment harge. late payment charge of 1.5% per month equivalent to 18% per annum will be charged on past due balances owed ompany. Provided however, that in the event that applicable governmental law sets a maximum rate for late payment fees which is less than 18% per annum, then the late payment charge assessed will be set at the maximum rate permitted by law. however, a security interest will remain in the Products, regardless of mode of attachment to realty or other property, until full payment has been made therefore, and ustomer agrees, upon request, to do all things and acts necessary to protect ompany s interest by adequately insuring the Products against loss from damage from any cause and to have ompany named as an additional insured. opies of all ertificates of Insurance will be provided to ompany upon request. ustomer will also assist ompany in providing all necessary documents or signatures required to file any documents to perfect ompany s interest in such Products. (d) reight harges. The full cost of freight, via a carrier of our choice, will be allowed (and prepaid) on shipments of the net dollar amount or more indicated in the chart below within the United States of merica, excluding all territores. rand Net ollar mount Schlage Mechanical $7,000 Schlage lectronic Security (excluding iometrics) $7,000 Schlage iometrics Refer to separate freight terms Von uprin $7,000 LN $7,000 IR STRK $7,000 alcon Locks $5,000 alcon xits $5,000 alcon losers $5,000 alcon STRK $5,000 Ives & lynn-johnson $1,000 Steelcraft Refer to separate freight terms On shipments of the net dollar amount or more to all foreign countries and US territories, freight will be allowed (and prepaid) to the Port of mbarkation. Shipments under the net dollar amount will be prepaid by Ingersoll Rand and 3.0% of the net invoice amount or $10, whichever is greater, will be added to the invoice. ll expedited methods of shipment, such as 'next day air', will be prepaid by Ingersoll Rand but the entire shipping costs will be added to the invoice. Ingersoll Rand will ship as requested, freight collect, if the customer is willing to bear the entire expense and so indicates on the order. Once received by IR, a purchase order cannot be combined with another purchase order to qualify for freight allowed. In addition the customer may not combine any of the brands or product categories listed above on a single purchase order to qualify for freight allowed, except in the case of STRK. IR STRK may not be combined with alcon STRK to qualify for freight allowed. (e) laims. ll claims for loss or damage to Products while in the care, custody, and/or control of a carrier will be the responsibility of ustomer, who will submit any claims. (f) Packing. ompany will pack, mark, and ship the Products according to its standard procedures for shipment, unless the parties agree, in writing, that ompany will comply with any special instructions provided by ustomer. ompliance with special instructions may result in an increased price. 5. LIMS.laims due to shortages, errors, omissions, damaged goods, or defective material must be submitted within 30 days from the date of the invoice. 6. PROUT HNS. ompany reserves the right to change without notice the design of, or the process of manufacturing, the Products covered by this greement; provided that the foregoing will not be construed as relieving ompany from its obligation to deliver Products which conform to the specifications which ompany may have furnished to ustomer. 7. PROUT RTURNS. Purchased material can only be returned to the factory by obtaining Return Material uthorization (RM) and must be returned to ompany within 90 days of issuance of the RM. Returned material must be new, unused, non-obsolete, and non-specially manufactured and been in ustomer s inventory no more than 180 days from the date of shipment by ompany. The RM number, the original invoice number, and the reason for the return must be included in the return. If the company approves the return, a credit will be issued to the ustomer s account less freight and a handling charge of 35% of the net material on the original invoice. Handling charges may vary depending on the condition of the return. The amount of final credit will be determined upon receipt at the factory and analyzing the condition of the material. actory retains the right to deny credit to anyone for any reason. 4. INSPTION, LIVRY, SHIPPIN, RIHT HRS, LIMS, 8. N THNIL INORMTION N VI.(a) ll designs, data, and PKIN.(a) Inspection. Inspection of Products and Services will be done by specifications provided by ompany are proprietary and will not be disclosed or reused ustomer immediately after receipt of Products or completion of Services. Inspection of by ustomer without the prior written consent of ompany. (b) ompany assumes no Products or Services by ustomer at ompany's facility is not permitted. (b) elivery. obligation or liability for any advice given by ompany, the results obtained, or Product delivery schedules are based upon current production capacities, material or damages incurred, and all such advice is given and accepted at ustomer s risk. component availability, and inventory, and may be changed by ompany as conditions require. Service delivery schedules are based upon prompt receipt of, and prompt access 9. LIMIT WRRNTY. to, ustomer s equipment and all information necessary to complete the Services. In no (a) ompany's Standard Limited Warranty(ies) relating to Products or Services event will Product or Service delivery dates be construed as falling within the meaning of are applicable to this greement. The limited warranty(ies) are (i) attached to this time is of the essence. Partial delivery shall be accepted by ustomer and paid for at the greement; (ii) separately identified in the specific Product Price ook; or price and on the terms stated herein. ny partial delivery of Products or Services, shall (iii) separately furnished by ompany to ustomer. constitute a separate sale and payment shall be separately made when due. If any part of (b) (i) In the event that certain Product warranties are not attached to this greement or the Products or Services are not delivered by ompany in accordance with ustomer s separately furnished, ompany warrants only to ustomer that Products will be free from order, this greement shall not be affected thereby. (c) Shipping.Unless otherwise defects in material and workmanship for a period of 12 months from the date of shipment specified by ompany, (i) where the ustomer is located in the United States, all Products of the Products. ompany s sole obligation under this warranty is limited to repairing or will be sold Uniform ommercial ode,.o.. Origin, ompany's factory ; and (ii) replacing, at its option, the defective Products. (ii) The provisions of this limited Product where the ustomer is located outside of the United States, all Products will be sold warranty do not apply to Products: () used for the purposes for which they are not x-works, ompany's factory (Incoterms 2000). In either instance, title and risk of designed or intended; () which have been repaired or altered without ompany's prior loss will pass to ustomer upon delivery to the carrier at ompany's factory. Provided

4 written consent; () which have been subjected to misuse, abuse, negligence, or accident; () which have been improperly stored, installed, maintained, or operated; () which have been used in violation of written instructions provided by ompany to ustomer; () which have subjected to improper temperature, humidity, or other environmental conditions; () which have been affected by normal wear and tear; or (H) which, based on ompany's examination, do not disclose to ompany's satisfaction nonconformance to the warranty. (c) (i) In the event that certain Service warranties are not attached to this greement or separately furnished, ompany warrants only to ustomer that the Services will be free from defects in material and workmanship for a period of 6 months from the date of completion of the particular items of Service. ompany s sole obligation under this warranty is limited to repairing or reperformance, at its option, of the Service; provided however, if repair or reperformance is either impractical or impossible, the ompany will refund to ustomer that portion of the price paid to the ompany for the defective item of Service. This warranty only applies if the company is given written notice of the defect or nonconformance by the ustomer within 30 days of discovery. (ii) The provisions of this limited Service warranty does not apply to any defects or issues with the design or performance of equipment or products not manufactured by ompany, nor does it apply to any code compliance or permit requirements for the assembly, installation, erection, or construction of any goods. (d) NO OTHR WRRNTIS, XPRSS OR IMPLI, R M WITH RSPT TO TH PROUTS OR SRVIS INLUIN, UT NOT LIMIT TO, NY IMPLI WRRNTY O MRHNTILITY OR IT - NSS OR PRTIULR PURPOS. (e) The following costs and expenses are not covered by the provisions of these limited warranties: (i) labor costs for the removal and reinstallation of Products or other manufacturer s products; (ii) shipping and freight expenses required to return Products to ompany; (iii) normal maintenance; and (iv) economic losses. In addition, the provisions of this warranty are not applicable to anything other than defects in ompany s material (products only) or workmanship. 10. USTOMR S RMIS.TH USTOMR S XLUSIV N SOL RMY ON OUNT O, OR IN RSPT O, TH URNISHIN O PROUTS OR SRVIS THT O NOT ONORM TO THIS RMNT WILL TO () SUR RPIR OR RPLMNT O TH PROUTS; OR () SUR RPIR OR RPRORMN O TH SRVIS OR TO OTIN RUN O TH PRI PI OR TH TIV SRVI, LL T OMPNY S OPTION. IN NO VNT WILL TH OMPNY S MXIMUM LIILITY X TH SLLIN PRI OR TH PROUTS OR ITM O SRVI. Terms and onditions 11. LIMITTION O LIILITY. IN NO VNT WILL OMPNY LIL OR ININTL, ONSQUNTIL, INIRT, SPIL, OR PUNITIV loss of use, in any manner arising out of the nuclear incident, whether alleged to be due, MS INLUIN, UT NOT LIMIT TO, LOSS O US O TH in whole or in part by ompany or its suppliers. PROUTS, SRVI INTRRUPTION, LOSS O PROITS, LOSS O - RV19. NO INUMNTS.The parties hereto represent to each other and each agrees NU, INTRST, LOST OOWILL, WORK STOPP, that, neither it nor any person acting on its behalf has, in contravention of any applicable IMPIRMNT O OTHR OOS, LOSS Y RSON O SHUTOWN OR law, given or offered to give, or will give or offer to give, any sum of money or other NON-OPRTION, INRS XPNSS O OPRTION, OR LIMS material consideration to any person, directly or indirectly, as an inducement to obtain O USTOMR S USTOMRS, WHTHR S ON ONTRT, business hereunder or to influence the granting of licenses or other governmental WRRNTY, TORT (INLUIN, UT NOT LIMIT TO, STRIT permissions to enter into this greement or perform obligations hereunder. LIILITY OR NLIN), PTNT INRINMNT, OR OTHRWIS, VN I VIS O TH POSSIILITY O SUH MS. 12. STTUT O LIMITTIONS.NO TION RISIN OUT O NY LIM RH O THIS RMNT Y OMPNY MY ROUHT Y USTOMR MOR THN ON (1) YR TR TH US O TION HS RISN. 13. ONSUMR PROUTS. With respect to consumer products as defined under the Magnuson-Moss Warranty ct ( MMW ), the following statements are made. (a) Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. I NY IMPLI WRRNTY IS PROVI UNR TH MMW, IT IS LIMIT TO TH URTION O TH WRRNTY PROVI IN STION 9 OV.(b) Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. (c) This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 14. OR MJUR. ny delay or failure of ompany to perform its obligations hereunder will be excused to the extent that it is caused by an event or occurrence beyond its control such as, by way of example and not by way of limitation, acts of od, actions by any governmental authority (whether valid or invalid), governmental laws and regulations not presently in effect, fires, floods, windstorms, explosions, riots, natural disasters, wars, sabotage, accidents, labor problems (including, but not limited to, lockouts, strikes, and slowdowns) at ompany's facility, its source plant or their suppliers, inability to obtain power, material, labor equipment, or transportation, or court injunction or order. The delivery date will be extended for a time equal to that of the delay and the schedule for ompany s performance will be deemed adjusted in the individual order(s) to that effect. 15. NTIR RMNT N MNMNT. This greement, together with any attachments or supplements specifically referenced in this greement, constitutes the entire agreement between the parties hereto and supersedes all previous communications, representations, or agreements, either oral or written, between the parties hereto with respect to the subject matter hereof. No agreement or understanding varying or expanding this greement will be binding upon either party hereto unless it is in writing and signed by a duly authorized representative thereof. 16. TRMINTION. (a) This greement may be terminated by either party by giving 30 days' written notice to the other party in the event of failure by such other party to fulfill any of its obligations hereunder. However, if during the period of such notice, such other party remedies such failure, this greement will continue with the same force and effect as if such notice had not been given. (b) This greement may be terminated upon the written mutual consent of the parties. (c) ither party may immediately terminate this greement by giving written notice to the other party in the event of the happening of any of the following or any other comparable event: (i) insolvency of the other party; (ii) filing of a petition in bankruptcy by or against the other party; (iii) appointment of a receiver or trustee for the other party; or (iv) execution of an assignment for the benefit of creditors by the other party, all of which will allow ompany to demand reclamation of all affected orders. (d) xcept as provided in this section 16, ustomer may not terminate this greement, in whole or in part, unless ompany s prior written consent is obtained and ustomer agrees to pay all of ompany s cancellation charges. 17. OVRNIN LW; VNU; N XPNSS.(a)This greement and any disputes or controversies arising hereunder will be governed by and construed according to the internal laws of the State of Indiana, United States of merica, without regard to its conflict of law principles, and not including the United Nations onvention on ontracts for the International Sale of oods. (b) Jurisdiction and venue with respect to any action, proceeding, or suit in connection with this greement will reside in the courts of the State of Indiana. (c) ustomer agrees to pay for all expenses (including attorney s fees) incurred by ompany in enforcing the obligations of ustomer under this greement. 18. OMPLIN WITH LWS, XPORT ONTROLS, RTIITIONS, N NULR LIILITY. (a) This greement is be subject to, and ompany and ustomer will comply with, all laws and export controls, regulations, rules, orders, licenses, requirements, and governmental requests now or hereafter in effect in the United States of merica that pertain to the Products or the initial sale of the Products or that pertain to Services. Provided however, ompany is not responsible for obtaining or maintaining any permits for the performance of Services or the verification or compliance with any code requirements relative to the performance of Services. To the extent any sale of Products or Services pursuant to this greement may require approval of the U.S. overnment, ompany s obligations under this greement are conditioned upon the grant of such approval and upon compliance by ustomer with any restrictions imposed by the U.S. overnment in connection with such approval. (b) ertain Products are noted by ompany as tested by independent laboratories for compliance with UL and/or NSI standards. ny and all modifications or alterations to such Products will void such certification, and ompany is not liable to ustomer to certify any modified or altered Product. (c) In the event the Products are to be used in a nuclear facility, the ustomer shall, prior to such use, arrange for insurance or governmental indemnity protecting ompany against liability. The ustomer hereby releases and agrees to indemnify ompany and its suppliers for any nuclear damage including, but not limited to, 20. SVRILITY. If any provision of this greement is held to be invalid, illegal, or unenforceable under any statute, regulation, ordinance, executive order, or other rule of law, that provision will be deemed severed to the extent necessary to comply with such statute, regulation, ordinance, order, or rule. In the event such provision is deemed severed, the parties will negotiate in good faith to arrive at an alternative arrangement approximating the original business objective of the parties. The remaining terms and conditions of this greement will remain in effect. 21. NO IMPLI WIVR.The failure of either party at any time to require performance by the other party of any provision of this greement will in no way affect the right to require such performance at any time thereafter, nor will the waiver of either party of a breach of any provision of this greement constitute a waiver of any succeeding breach of the same or any other provision. 22. MISLLNOUS.(a) This greement does not constitute either party the agent or legal representative of the other party. Neither party is authorized to create any obligation on behalf of the other party including, but not limited to, the obligation for payment of any service or warranty obligation hereunder. (b) Neither this greement nor any right or obligation hereunder may be transferred or assigned by either party without the prior written approval of the other party, except that ompany can transfer or assign this greement or any right or obligation (including, but not limited to the right to receive payments for any orders) to Ingersoll-Rand ompany or an Ingersoll-Rand ompany entity without first obtaining ustomer s consent. (c) The rights and remedies herein reserved to ompany will be cumulative and additional to any other or further rights and remedies provided at law or equity. (d) ustomer does not have the right to setoff or to back charge against any amounts which become payable to ompany under this greement or otherwise. (e) The official text of this greement is in the nglish language. If this greement is translated into another language, the nglish text will govern any question with respect to interpretation. (f) The headings in this greement are for convenience of reference only and do not affect the meaning of this greement in any manner. 23. INITIONS.(a) greement means Ingersoll-Rand ompany, Security Technologies Sector Terms and onditions of Sale and Service. (b) ompany means Ingersoll-Rand ompany, Security Technologies Sector. (c) ustomer means the uyer. (d) uyer means the purchaser of products or Services from ompany. iii xterior Hardware

5 Index by Product escription xterior Hardware ngle Stop utomatic lush olt.....2, 3, 4 utomatic Wall Holder uxiliary Pusher all atch , 16 all atch, djustable all atch, ual djustable ar oordinator ar Window Lift racket road utt Hinge arry ar asement djuster asement astener , 8 eiling Hook hain oor uard hest Handle loset Pole Socket oat & Hat Hook , 4 onstant Latching lush olt oordinator, ar oordinator, iller ar oordinator, Mounting racket..13 rash Stop ecorative orner ecorative Hasp ecorative Hinge oor ase Stop, Residential 20, 21 oor olt, utch oor olt, Mortise oor uard, hain oor uard, Solid ar oor Knocker oor Numbers oor Pull , 3, 4, 5 oor Pull, Offset oor Silencer raw atch ust Proof Strike utch oor olt lbow atch iller ar inger Pull lexible oor Stop, Residential20, 21 loor Stop , 3, 4, 5 loor Stop & utomatic Holder 6, 8 loor Stop & Manual Holder loor Stop & Semi-automatic Holder6 lush olt, utomatic....2, 3, 4 lush olt, onstant Latching....5 lush olt, Manual6, 7, 8, 9, 10 lush Pull , 14 riction Lid Support ravity oordinator H Handrail racket Hasp Hinge Pin Stop , 22 Hinge, 3 Knuckle, ull Mortise , 6 Hinge, 5 Knuckle, ull Mortise , 7, 8, 9 Hinge, 5 Knuckle, Half Surface..10 Hinge, ontinuous Pin & arrel ull Mortise Hinge, ontinuous eared ull Surface , 20 Hinge, ontinuous eared Half Surface , 22 Hinge, ontinuous Pin & arrel ull Mortise, ull Wrap....29, 30 Hinge, ontinuous Pin & arrel Swing lear Hinge, lectrifies Hinge, Pocket Hinge, Residential Hobbyist arrel olt Holder, Kick own , 17 Hook and Hasp Hook and Staple I Invisible Latch K Kick own Holder , 17 Knocker, oor L Letter ox Plate Letter ox Sleeve Lock uard , 3, 4 M Magnetic atch Manual lush olt6, 7, 8, 9, 10 Manual Wall Holder , 14 Middle utt Hinge Mortise oor olt Mounting rackets N Numbers, oor P Pivot, 1/2" Offset , 44 Pivot, 3/4" Offset 36, 37, 38, 39, 40, 41, 42 Pivot, enter Hung 45, 46, 47, 48 Pivot, Intermediate , 50 Pivot, Intermediate, lectrified..51 Pivot, Pocket Pocket Sliding oor olt Protection Plates Pull Plate , 8 Pull Plate (less pull) Push ar Push ar with Pull Push Plate R Riser , 4 Roller umper Roller atch Roller Latch , 9, 10 S Screen oor Pull Side Window Lock Slide oor dge Pull Sliding oor Pull Solid ar oor uard Stop, rash Stop, Hinge Pin , 22 Strike Plate Strike, ust Proof Storm oor Latch Support Hinge Surface olt , 3 Surface olt, ecorative.....4, 5 V Vandal Resistant Trim.10, 11, 12 Viewer, One Way , 6 W Wall umper , 12 Wall Holder, utomatic Wall Holder, Manual , 14 Wall Stop , 10, 14 Wardrobe Hook Window Lock iv

6 v Nurmerical Part Index xterior Hardware P L M M M1V P M M M2V HW P SP M M M3V HW S SHW WT HW P , OR L S OR L L L WS WS11X L L S L L L R S S S18L S18S L WS WS20X L L L , RL OR L RL WS WS33X RL RL S WS S OR S S L H WS WS45X H S OR H , H , , OR , SR SR WS SR OR H S H H H S WS WS WS404VX WS WS R S R S R S S WS S WS S WS S WS S S S S R R R S S S S S , , , STK STK685L U U U U VR810-T VR810-NL VR814-T VR814-NL S VR VR900LLP VR910-T VR910M-T VR910M-NL VR910-NL RL S S S S1601M S1601M , / V-7222 INT V , INT INT PT-7226PT-7227PT , , INT INT J Z Z PT

7 inishes xterior Hardware HM US escription ase Material 609 US5 Satin rass Plated, lackened, Satin Relieved, lear oated luminum 628 US28 Satin luminum, lear oated luminum 666 US3 right rass Plated, lear oated luminum 666 US3L right rass Plated, lear oated luminum 667 US4 Satin rass Plated, lear oated luminum 668 US10 Satin ronze Plated, lear oated luminum 668 US10L Satin ronze Plated, lear oated luminum 669 US14 right Nickel Plated luminum 670 US15 Satin Nickel Plate luminum 673 US92 luminum, lear oated luminum 689 US65 luminum Painted luminum 702 US26 Satin hrome Plated luminum 703 US10 Oxidized Satin ronze Plated, Oil Rubbed luminum N ark ronze nodized luminum N lack nodizes luminum 713 US26 luminum Satin ronze Plated, lear oated luminum LK lack poxy oated luminum W White poxy oated luminum T Tan poxy oated luminum RN rown poxy oated luminum LR lear xpoxy oated luminum US5 Satin rass Plated, lackened, Satin Relieved, lear oated luminum 5 luminum luminum P luminum, Prime Paint luminum R Red poxy oated luminum US26 Satin hrome Plated luminum 690 US69 ark ronze Painted ny 605 US3 right rass, lear oated rass 606 US4 Satin rass, lear oated rass 689 SP28 luminum Painted rass 691 SP10 Light ronze Painted rass 693 SPLK lack Painted rass 695 SP313 ark ronze Painted rass 706 SP4 rass rass 716 Satin ronze Plated, lear oated rass P600 P600 Primed for Paint rass RN rown rass RY ray rass TN Tan rass White White Rubber rass 618 US14 right Nickel Plated, lear oated rass, ronze 619 US15 Satin Nickel Plated, lear oated rass, ronze 620 US15 Satin Nickel Plated, lackened, Satin Relieved, lear oated rass, ronze 622 US19 lat lack oated rass, ronze 625 US26 Polished hrome Plated rass, ronze 626 US26 Satin hrome Plated rass, ronze 612 US10 Satin ronze, lear oated ronze vi

8 inishes HM US escription ase Material 613 US10 ark Oxidized Satin ronze, lear oated ronze White White Plastic LK lack Plastic Plastic RN rown Plastic Plastic LR lear Plastic Plastic P Plastic Plastic 3 Rubber Rubber R Rubber Rubber rown rown Rubber Rubber Tan Tan Rubber Rubber ray ray Rubber Rubber 629 US32 Polished Stainless Steel Stainless Steel US32 Satin Stainless Steel Stainless Steel USP Primed for Paint - Steel Steel 600 P Primed for Paint - Steel Steel Zinc Plated Steel Zinc Plated Steel Zinc Plated/ichromate Sealed Steel 632 US3 right rass Plated, lear oated Steel 638 US5 Satin rass Plated, lackened, Satin Relieved, lear oated Steel 639 US10 Satin ronze Plated, lear oated Steel 640 US10 ark Oxidized Satin ronze, lear oated Steel 645 US24 right Nickel Plated, lear oated Steel 646 US15 Satin Nickel Plated, lear oated Steel 652 US26 Satin hrome Plated Steel 689 SP28 luminum Painted Steel 693 SPLK lack Painted Steel 695 SP313 ark ronze Painted Steel 695 SP313 ark ronze Painted Steel 706 SP4 rass Steel 716 Satin ronze Plated, lear oated Steel Steel 5 Steel Steel 406 Zinc/rass ntimicrobial oating (M) inhibits the growth of bacteria, available on many Ives rchitectural Hardware Products. xterior Hardware vii

9 xterior Hardware Packaging, Handing Packaging Key Many Ives items are available in a variety of packaging forms designated by a prefix. The Ives Price ook contains the specific packaging options for each Ives product. elow is a description of these options. Symbol escription of Package S arded ommercial rade arded Schlage randed arded SP Slim-Pak SPS oor Handing Schlage randed Slim-Pak LH INSI RH Left Hand Right Hand OUTSI INSI LR RR Left Hand Right Hand Reverse evel OUTSI Reverse evel viii

10 xterior Hardware rchitectural Hinges, ontinuous Hinges and Pivots Table Of ontents rchitectural Hinges page eneral Hinge Information How to Order NSI Hinge Identification Reference P1 3 Knuckle, ull Mortise Knuckle, ull Mortise HW 3 Knuckle, ull Mortise SP1 3 Knuckle, ull Mortise P1 5 Knuckle, ull Mortise Knuckle, ull Mortise HW 5 Knuckle, ull Mortise WT 5 Knuckle, ull Mortise Knuckle, ull Mortise HW 5 Knuckle, ull Mortise S 5 Knuckle, ull Mortise SHW 5 Knuckle, ull Mortise lectrified Hinge Residential Hinges ontinuous Hinges Pivots

11 rchitectural Hinges, ontinuous Hinges and Pivots 2 xterior Hardware eneral Hinge Information SLTION O TH PROPR WIHT N RIN TYP Standard Weight..... Plain earing Standard Weight..... all earing, oncealed earing Heavy Weight all earing, oncealed earing ONSIRTIONS TO TRMIN WIHT N RIN TYP: - Weight of oor - requency of use - rame - oor Hardware lways use ball bearing or concealed bearing hinges for doors with door closers and in all fire rated openings. Heavy weight doors and high frequency doors should use heavy weight ball bearing or concealed bearing hinges. UILINS OR HIN MTL - Interior door or non-corrosive area use: Plated or painted Steel - Interior labeled door use: Plated or Painted Steel, Stainless Steel - Interior door in corrosive area use: Stainless Steel, rass, ronze - xterior doors use: Stainless Steel, rass, ronze Standard pin material are rass Hinge Steel Pin, Stainless Steel Hinge Stainless Steel Pin, Steel Hinge Steel Pin UILINS OR RQUNY O OOR US: uild Type aily Usage Hinge Type High requency/ Heavy Weight oor Large epartment Store ntrance 5,000 Heavy Weight Hospital orridor and Surgical oors 5,000 Heavy Weight Large Office uilding ntrance 4,000 Heavy Weight School ntrance 1,250 Heavy Weight School Toilet oor 1,250 Heavy Weight Office Stairwell 500 Heavy Weight Office uilding Toilet oor 400 Heavy Weight Medium requency/ Medium Weight oor School orridor oor 100 Standard Weight Hospital onsultation Rooms 100 Standard Weight Office uilding orridor oor 80 Standard Weight Store Toilet oor 60 Standard Weight Storage Room 50 Standard Weight Low requency /Light oor Residential ntrance 30 Plain earing Interior Residential 20 Plain earing NSI/HM R/MINIMUM YL RQUIRMNTS rade 1: 2,500,000 Heavy Weight all & oncealed earing rade 2: 1,500,000 Standard Weight all & oncealed earing rade 3: 350,000 Light Weight Plain earing ONSIRTIONS TO TRMIN HIN SIZ - oor Width - oor Thickness - Weight - learance UILINS OR HIN HIHT OOR THIKNSS OOR WITH HIN HIHT IN INHS IN INHS IN INHS 1-3/8 Up to /2 1-3/8 32 to /4 Up to /2 1-3/4 36 to /4 Over /2 Up to 42 5 heavy weight 2-2-1/2 Over 42 6 heavy weight LRN RQUIRMNT* OOR THIKNSS LRN N HIN OPN WITH 1-3/8 3/ / /4 1-1/2 4-1/2 1-3/ / / / / / / /2 3/ /2 1-3/ / /4 8 *istance needed between wall and door at 180º to allow for any projections from wall; trim, decorative molding, etc. UILINS OR NUMR O HINS - oors under 7'6" hinges - oors over 7'6" hinges LOTION O HINS 5" (127mm) 10" (254mm) qual Top hinge 5" from jamb rabbet to top of barrel ottom hinge 10" from bottom edge of barrel to finished floor Third hinge centered between top and bottom hinges Note: Some western states use a standard 7" from top and 11" from the bottom 2

12 rchitectural Hinges, ontinuous Hinges and Pivots Ives Hinge Number System Please note: or availability of specific models, please refer to the item s catalog page or consult ustomer Service. How to Order: HW 4.5x NRP 3 Number of Knuckles: 3-3 Knuckle 5-5 Knuckle unction: P Plain earing all earing oncealed earing SP Spring Hinge Type: 1 ull Mortise 2 Half Mortise 3 ull Surface 4 Half Surface Weight/Options: lank Standard Weight HW Heavy Weight S Swing lear SH Security Stud WT Wide Throw HT Hospital Tip R Round orners, 1/4" or 5/8" Radius Size xamples: 3.5 x x 5 4 x x x 4 5 x x x 5 5 x 6 5 x 7 Larger sizes, up to 6 x 8 are available. onsult factory. inish (Some models require extended lead times): 600 USP - Steel 605 US3 - rass 606 US4 - rass 612 US10 - rass 613 US10 - rass 619 US15 - rass 625 US26 - rass 626 US26 - rass 630 US32 - Stainless 632 US3 - Steel 633 US4 - Steel 639 US10 - Steel 640 US10 - Steel 641 US10 - Steel 643 US11 - Steel 646 US15 - Steel 651 US26 - Steel 652 US26 - Steel Special Pins pplications: NRP Non-Removable Pin TW4 our Wire TW8 ight Wire MON Monitor TW4M our Wire with Monitor TW8M ight Wire with Monitor 3 xterior Hardware

13 rchitectural Hinges 4 xterior Hardware NSI Hinge Identification Reference = NSI irst number indicates material 1 ast, forged or extruded brass or bronze 2 Wrought brass or bronze 5 Stainless steel 8 Wrought or forged steel, or malleable iron Second number indicates product type 1 ull mortise 2 Half mortise 3 ull surface 4 Half surface 5 nchor, pivot reinforced or thrust pivot unit or hinge sets 6 Olive knuckle hinges 7 Pivot hinge 8 Rescue hardware Third number indicates function 1 nti-friction bearing 2 nti-friction bearing, swing clear 3 Plain bearing 4 4 to 0, special conditions ourth number indicates grade 1 rade 1, 4 xtra Heavy uty 2 rade 2, 2 Standard uty 3 rade 3, Plain earing xample: 8111 Steel, ull Mortise, nti-friction, rade Stainless, ull Mortise, nti riction earing, rade 2 4

14 rchitectural Hinges Meets NSI/HM Steel 5133 Stainless Steel 2133 rass 3P1 3 Knuckle, Plain earing ull Mortise Hinge or standard weight doors Low frequency usage Packed with wood and metal screws Not for use with a door closer. Options NRP, Non-Removable Pin SH, Security Stud HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security asteners - Pin-in-Socket Size (Inches) Size (mm) auge 3.5 x x x x x x x x x x Meets NSI/HM Steel 5112 Stainless Steel 2112 rass 31 3 Knuckle, oncealed earing ull Mortise Hinge or standard weight doors Medium frequency usage Packed with wood and metal screws Options NRP, Non-Removable Pin SH, Security stud HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge 3.5 x x x x x x x x x x inishes brass Ives inish US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes steel Ives inish USP US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes stainless steel Ives inish US32 US32 HM xterior Hardware 5

15 rchitectural Hinges 6 Meets NSI/HM Steel 5112 Stainless Steel 2112 rass Meets NSI/HM K81071 Steel K51071 Stainless Steel UL listed for use with fire rated doors 31HW 3 Knuckle, oncealed earing ull Mortise Hinge or heavy weight doors High frequency usage Packed with wood and metal screws Options NRP, Non-Removable Pin SH, Security stud HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge 4.5 x x x x x x x x SP1 3 Knuckle Spring ull Mortise Hinge or automatic closing of doors Packed with wood and metal screws Options HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge 4 x x x x x x xterior Hardware inishes brass Ives inish US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes steel Ives inish USP US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes stainless steel Ives inish US32 US32 HM

16 rchitectural Hinges 5P1 5 Knuckle, Plain earing ull Mortise Hinge or standard weight doors Low frequency usage Packed with wood and metal screws Not for use with a door closer. 7 Meets NSI/HM Steel 5133 Stainless Steel 2133 rass Options NRP, Non-Removable Pin SH, Security Stud HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge 3.5 x x x x x x x x x x Meets NSI/HM Steel 5112 Stainless Steel 2112 rass 51 5 Knuckle, all earing ull Mortise Hinge or standard weight doors Medium frequency usage 2 ball bearing Packed with wood and metal screws Options NRP, Non-Removable Pin SH, Security Stud HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge 3.5 x x x x x x x x inishes brass Ives inish US3 US4 US10 US10 US10 US11 US15 US26 US26 HM Size (Inches) Size (mm) auge 5 x x x x inishes steel Ives inish USP US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes stainless steel Ives inish US32 US32 HM xterior Hardware 7

17 rchitectural Hinges 8 51HW 5 Knuckle, all earing, Heavy Weight ull Mortise Hinge or heavy weight doors High frequency usage 4 ball bearing Packed with wood and metal screws Meets NSI/HM Steel 5111 Stainless Steel 2111 rass Meets NSI/HM Steel Options NRP, Non-Removable Pin SH, Security Stud HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge 4.5 x x x x WT 5 Knuckle, all earing, Wide Throw ull Mortise Hinge or medium weight doors Medium frequency usage 2 ball bearing Packed with wood and metal screws Options NRP, Non-Removable Pin SH, Security Stud HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge 5 x x x x xterior Hardware Size (Inches) Size (mm) auge 4.5 x x x x x x x x x x inishes brass Ives inish US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes steel Ives inish USP US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes stainless steel Ives inish US32 US32 HM

18 rchitectural Hinges 54 5 Knuckle, all earing, Half Surface Hinge or standard weight doors Medium frequency usage 2 ball bearing Packed with through bolts, grommets and sheet metal screws 9 Meets NSI/HM Steel Meets NSI/HM Steel Options NRP, Non-Removable Pin HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge HW 5 Knuckle, all earing, Half Surface Heavy Weight Hinge or heavy weight doors High frequency usage 4 ball bearing Packed with through bolts, grommets and sheet metal screws Options NRP, Non-Removable Pin HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge inishes brass Ives inish US3 US4 US10 US10 US10 US11 US15 US26 US26 HM xterior Hardware inishes steel Ives inish USP US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes stainless steel Ives inish US32 US32 HM

19 rchitectural Hinges 10 51S 5 Knuckle, all earing, Swing lear ull Mortise Hinge or standard weight doors Square edge standard Medium frequency usage 2 ball bearing Packed with flat head wood and metal screws esigned to completely clear the opening when door is opened 92 degrees. Meets NSI/HM Steel 5122 Stainless Steel 2122 rass Options NRP, Non-Removable Pin, beveled edge door HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket Size (Inches) Size (mm) auge SHW 5 Knuckle, all earing, Swing lear Heavy Weight ull Mortise Hinge or heavy weight doors eveled edge standard High frequency usage 2 ball bearing Packed with flat head wood and metal screws esigned to completely clear the opening when door is opened 92 degrees. Meets NSI/HM Steel Options NRP, Non-Removable Pin, beveled edge door HT, Hospital Tip R, Round orners - 1/4" or 5/8" Radius S, Security astners - Pin-in-Socket xterior Hardware Size (Inches) Size (mm) auge inishes brass Ives inish US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes steel Ives inish USP US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes stainless steel Ives inish US32 US32 HM

20 rchitectural Hinges UL Listed - UL634 Meets NSI/HM Steel 5111 Stainless Steel 2111 rass lectrified Hinge vailable Options - Through Wire - TW4 (4 wires) & TW8 (8 wires) - Monitor MON - Through Wire with Monitor TW4M & TW8M vailable in 3 and 5 Knuckle One hinge per box, packed with wood and machine screws Hinge is NRP as a standard High quality brass ferrules and plastic tubing protect the wires Through-wire hinges cycle tested to ensure durability Ives warranty applies - 12 months from date of shipment Through-Wire is rated for 50 volts / at 3.5 amp continuous and 16 amp pulse, maximum pulse 400 mili second. Monitor rated 30V at.5 amp inishes brass Ives inish US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes steel Ives inish USP US3 US4 US10 US10 US10 US11 US15 US26 US26 HM inishes stainless steel Ives inish US32 US32 HM xterior Hardware 11

21 rchitectural Hinges 12 xterior Hardware 1010 Schlage arded Only 1012 Schlage arded Only Schlage arded Only 1000 Series Residential Hinges ull mortise hinges in 2 sizes: 3-1/2" and 4". Two corner options: Square corners and 5/8" or 1/4" radius corners. Substrates include: Steel. Model Size orner /2" x 3-1/2" Square orner /2" x 3-1/2" 5/8" Radius orner /2" x 3-1/2" 1/4" Radius orner " x 4" Square orner " x 4" 5/8" Radius orner inishes steel Ives inish * 625** 716 HM * not available on 1012 hinge * only available on Schlage arded Only 12

22 ontinuous Hinges Ives ontinuous Hinges are designed to last the life of the building. The unique design distributes the weight of the door along the entire length of the frame, reducing the high amount of stress normally associated at top of door and frame on butt hinge applications. Not only does this reduce hinge failure, it also keeps your door in constant alignment, eliminating the chance of door sag. These characteristics make continuous hinges suitable for high use/high traffic doors. The design of a continuous hinge eliminates the gap between the door and the frame. The absence of gap also helps prevents finger from being pinched, making it a safer device than traditional hinges. These benefits result in higher efficiency and less maintenance, maximizing the value of your opening investment. ontinuous hinges are available in two styles; aluminum geared and pin and barrel in steel or stainless steel. ontinuous Hinge Table Of ontents page ontinuous Hinge Types ross Reference uide luminum eared Hinges eneral Information lectrified Options How to Order oor Sizing H Half Surface H Half Surface H Half Surface H Half Surface H ull Mortise H ull Surface, enter Pivot H ull Surface, Swing lear H ull Mortise, dge Protector lectrical utouts Pin and arrel Hinges eneral Information lectrified Options How to Order oor Sizing , ull Mortise , ull Surface , Swing lear ull Mortise, ull Wrap ull Mortise, ull Wrap lectrical utouts xterior Hardware

23 ontinuous Hinges 14 xterior Hardware luminum eared eared continuous hinges utilize a single gear section for the leaf and a separate gear section for the frame side of the door. The two are held in place together by a full length cover channel and rotate on a series of bearings. Pin and arrel Pin and arrel hinges share many of the same characteristics of a traditional hinge. oth have a center pin and rolled knuckles. However, a continuous Pin and arrel hinge stretches along the entire length of the frame. IVS offers both stainless steel and primed steel to best match your specific application. Lifetime Warranty Ives continuous hinges carry a limited lifetime warranty, ensuring your opening will function to your satisfaction every time. 14

24 ontinuous Hinges ross Reference uide 15 Ives Hager Markar McKinney Pemko Select Stanley eared 045H H 046H H 053H H 054H H 112H H MK-12H MSLH SL11H 661H 210H H MK-22H SH SL21H 665H 224H H MK-25H MH SL24H 662H 157H H MK-58H SPH SL57H 664H Pin and arrel 600 M200 SL S N/ M300 SL S302 SL H305 SL H311 SL H xterior Hardware 15

25 ontinuous Hinges 16 luminum eared Hinges eneral Information Material 6063-T6 luminum Standard Lengths 83", 85", 95", 120" ustom lengths are available up to 120", consult factory. inishes L - US28 (628) lear nodized R - 313N (710) ark ronze Hinge uty ll Ives luminum eared Hinges are Heavy uty (H). mount of bearings varies by size: 83" 32 earings 85" 32 earings 95" 36 earings 120"- 47 earings oor Weight ach hinge can hold a door up to 450 lbs (Rivet nuts recommended) and a max door width of 4'0". NSI ertified ll Ives luminum eared Hinges are certified to NSI , rade 1 UL Listed ll Ives luminum eared Hinges are tested and approved UL 10 (90 minutes). ield Modifications: ll Ives luminum eared ontinuous Hinges can be cut to length during installation. The unique mounting pattern allows to cut up to 6" from bottom while still having double row fasteners. If cut more than 13.5", other modifications may be necessary. lectrification Options Only available for the full mortise hinges xterior Hardware lectric Power Transfer (PT) lectric power transfer provides a means of transferring power from the door frame to the edge of a swinging door. Ives ontinuous Hinges provide standard cut outs to fit Von uprin PT-2, PT-10 and PNT-1 devices. onsult factory for other electrical cut out options. lectrical Through-Wire (TW) Provides electric power transfer from the frame to the door in order to supply power to an electrified mortise or cylindrical locks, exit devices with electric latch retraction, and/or electric strikes (pairs of doors). Through-wire is rated 50 volts / at 3.5 amp continuous and 16 amp pulse. Maximum pulse 400 milliseconds. Ives thru-wire hinges are fully compatible with 4 wire and 8 wire installations. 16

26 ontinuous Hinges luminum eared Hinges How to Order: H - L PT Model 045H 046H 053H 054H 112H 157H 210H 224H inish L R Half Surface Half Surface Half Surface Half Surface ull Mortise ull Surface - enter Pivot ull Surface - Swing lear ull Mortise - dge Protector lear ronze Length 83" 85" 95" 120" Other lengths available up to 120", consult factory. Handing required. Options * PT lectric Power Transfer Prep * TW8 lectric Through Wire S Security asteners - Pin-in-Socket W Wood asteners HM Thread forming screws (pilot hole required) * ull Mortise Models Only xterior Hardware 17

27 ontinuous Hinges 18 luminum eared Hinges - learance Requirements Hinge Side learance 1/8 Hinge Side learance 3/16 Hinge Side learance 1/32 rame Irregularity 1/16 rame Irregularity xterior Hardware SINL OOR oor Under-Sizing Hinge-Side Lock-Side rame eveled oor Square eveled Model learance learance Irregularity learance dged dged 045H 5/32" 1/8" 1/32" 1/32" 5/16" 11/32" 046H 5/32" 1/8" 1/32" 1/32" 5/16" 11/32" 053H 5/32" 1/8" 1/32" 1/32" 5/16" 11/32" 054H 5/32" 1/8" 1/32" 1/32" 5/16" 11/32" 112H 5/16" 1/8" 1/32" 1/32" 15/32" 1/2" 224H 5/16" 1/8" 1/32" 1/32" 15/32" 1/2" 210H 1/16" 1/8" 1/32" 1/32" 7/32" 1/4" 157H 1/16" 1/8" 1/32" 1/32" 7/32" 1/4" PIR O OORS oor Under-Sizing Square Square eveled eveled Hinge-Side Lock-Side rame eveled oor dged dged dged dged Model learance learance Irregularity learance Total ach oor Total ach oor 045H 5/32" 3/16" 1/16" 1/16" 9/16" 9/32" 5/8" 5/16" 046H 5/32" 3/16" 1/16" 1/16" 9/16" 9/32" 5/8" 5/16" 053H 5/32" 3/16" 1/16" 1/16" 9/16" 9/32" 5/8" 5/16" 054H 5/32" 3/16" 1/16" 1/16" 9/16" 9/32" 5/8" 5/16" 112H 5/16" 3/16" 1/16" 1/16" 7/8" 7/16" 15/16" 15/32" 224H 5/16" 3/16" 1/16" 1/16" 7/8" 7/16" 15/16" 15/32" 210H 1/16" 3/16" 1/16" 1/16" 3/8" 3/16" 7/16" 7/32" 157H 1/16" 3/16" 1/16" 1/16" 3/8" 3/16" 7/16" 7/32" Templates and installation instructions available on line at ives.ingersollrand.com 18

28 ontinuous Hinges 045H Half Surface ontinuous Hinge Half surface for retrofit or new construction Non-handed rame leaf depth 1-9/16" 9/32" door inset 19 Standard lengths 83", 85", 95", 120" Standard Mounting Hardware x 1/2" steel self tapping screw 1/4-20 x 1-1/2" L Sex olt 1/4-20 x 1" Steel Shoulder olt x 3/4" Steel Self rilling Shoulder olt Optional S-Security asteners available inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 2-9/32" 1-9/16" 3-1/16" 1-9/32" 046H Half Surface ontinuous Hinge Half surface for retrofit or new construction Non-handed rame leaf depth 1-15/16" 9/32" door inset Standard lengths 83", 85", 95", 120" Standard Mounting Hardware x 1/2" steel self tapping screw 1/4-20 x 1-1/2" L Sex olt 1/4-20 x 1" Steel Shoulder olt x 3/4" Steel Self rilling Shoulder olt Optional S-Security asteners available inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 5/32" learance for Square dge oor 3/16" learance or eveled dge oor 2-5/8" 1-15/16" 5/32" learance for Square dge oor 3/16" learance or eveled dge oor 3-1/16" 1-9/32" 19 xterior Hardware

29 ontinuous Hinges H Half Surface ontinuous Hinge Half surface for retrofit or new construction Non-handed rame leaf depth 1-9/16" 1/8" door inset Standard lengths 83", 85", 95", 120" Standard Mounting Hardware x 1/2" steel self tapping screw 1/4-20 x 1-1/2" L Sex olt 1/4-20 x 1" Steel Shoulder olt x 3/4" Steel Self rilling Shoulder olt Optional S-Security asteners available inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 2-9/32" 1-9/16" 2-1/8" 1-5/32" 054H 5/32" learance for Square dge oor 3/16" learance or eveled dge oor Half Surface ontinuous Hinge Half surface for retrofit or new construction Non-handed rame leaf depth 1-15/16" 1/8" door inset xterior Hardware 20 Standard lengths 83", 85", 95", 120" Standard Mounting Hardware x 1/2" steel self tapping screw 1/4-20 x 1-1/2" L Sex olt 1/4-20 x 1" Steel Shoulder olt x 3/4" Steel Self rilling Shoulder olt Optional S-Security asteners available inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 2-5/8" 1-15/16" 5/32" learance for Square dge oor 3/16" learance or eveled dge oor 2-1/8" 1-5/32"

30 ontinuous Hinges 112H ull Moritse luminum eared ontinuous Hinge Non Handed lush Mounted, No Inset 48" Maximum oor Width eveled or Square dge oors or oors Weighing up to 450 pounds without reinforcing, 600 pounds with reinforcing 21 Standard lengths 83", 85", 95", 120" Standard Mounting Hardware X 3/4" Steel Self rilling, Self Tapping Screws Optional W - Wood Screws or S - Security asteners vailable inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 157H 5/16" learance for Square dge oor 1/32" learance or eveled dge oor ull Surface, enter Pivot luminum eared ontinuous Hinge Non Handed Narrow rame 1/16" oor Inset 48" Maximum oor Width eveled or Square dge oors or oors Weighing up to 600 pounds Standard lengths 83", 85", 95", 120" Standard Mounting Hardware X 1/2" Steel Self Tapping Screws, 1/4-20 X 1-1/2" L Sex olt, 1/4-20 X 1" Steel Shoulder olt, X 3/4 Steel Self rilling, Optional S - Security asteners vailable inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 1/16" learance for Square dge oor 3/32" learance or eveled dge oor xterior Hardware 21

31 ontinuous Hinges H ull Surface, Swing lear luminum eared ontinuous Hinge Non Handed 1/32" oor Inset 48" Maximum oor Width eveled or Square dge oors or oors Weighing up to 600 pounds Standard lengths 83", 85", 95", 120" Standard Mounting Hardware X 1/2" Steel Self Tapping Screws, 1/4-20 X 1-1/2" L Sex olt 1/4-20 X 1" Steel Shoulder olt, X 3/4" Steel Self rilling, Optional S - Security asteners vailable inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 224H 1/16" learance for Square dge oor 3/32" learance or eveled dge oor ull Mortise luminum eared ontinuous Hinge Non Handed oor dge Protector 48" Maximum oor Width 1/16" oor Inset eveled or Square dge oors or oors Weighing up to 450 pounds without reinforcing, 600 pounds with reinforcing xterior Hardware Standard lengths 83", 85", 95", 120" Standard Mounting Hardware X 3/4" Steel Self rilling, Self Tapping Screws Optional W - Wood Screws or S - Security asteners vailable inishes lear (L), ark ronze () ustom nodizing and Painting are available, consult factory. 22 5/16" learance for Square dge oor 1/32" learance or eveled dge oor

32 ontinuous Hinges PT 112H Top of hinge/door PT 224H Top of hinge/door lectrical utouts Ives luminum eared ontinuous Hinges are available with factory modified cutouts to accommodate most electrical frame to door requirements. Special templates are required. T 23 PT L PT L When ordering indicate the following: 1. Opening size. 2. Handing. LH, RH, RHR or LHR. 3. Manufacturer and model number of the electrical product being used. xample; Von uprin PT2 ecause clearances may vary between door and frame manufacturer, and locations can be influenced by the door hardware it is always recommend contacting Ives ustomer Technical for specific template information. or your general information below are standard locations for Von uprin PT2 or PT10, and monitor switch. rom Top dge of oor to enter Line of ut-out TW 112H 224H Standard 112H 224H 112H/224H Length PT PT TW 83" 30" 30" 41-1/2" 85" 32" 32" 42-1/2" 95" 42" 42" 57-3/4" 120" 67" 67" 81-25/32" Top of hinge/door TW L xterior Hardware 23

33 ontinuous Hinges 24 xterior Hardware Pin and arrel Hinges eneral Information Standard Lengths 83", 85", 95", 120" ustom lengths are available up to 120", consult factory. inishes US32 (630) Satin Stainless Steel USP (600) Steel, Primed for Paint arrel Type Twin Self Lubricated Nylon earings with Stainless Steel Pin. oor Weight ach hinge can hold a door up to 600 lbs (Rivet nuts recommended) and a max door width of 4'0". NSI ertified ll Ives Pin and arrel Hinges certified to NSI , rade 1. UL Listed ll Ives Steel and Stainless Steel Pin and arrel Hinges are tested and approved UL 10 (3 hr). ield Modifications ll Ives Pin and arrel ontinuous Hinges can be cut to length during installation. If more than 6" from bottom of hinge, additional modifications may be necessary. lectrification Options Only available for the ull Mortise Hinges lectric Power Transfer (PT) lectric power transfer provides a means of transferring power from the door frame to the edge of a swinging door. Ives ontinuous Hinges provide cut outs to fit Von uprin PT-2, PT-10 and PNT-1 devices. onsult factory for other PT cut out options. lectrical Through-Wire (TW) Provides electric power transfer from the frame to the door in order to supply power to an electrified mortise or cylindrical locks, exit devices with electric latch retraction, and/or electric strikes (pairs of doors). Through-wire is rated for 3.5 amp continuous and 16 amp pulse. Ives thru-wire are fully compatible with 4 wire and 8 wire installations. 24

34 ontinuous Hinges Pin and arrel Hinges 25 How to Order: US PT Model Stainless Steel 700 ull Mortise 702 ull Surface - enter Pivot 705 ull Mortise - ull Wrap 711 ull Surface - Swing lear 715 ull Mortise - Half Wrap Steel 600 ull Mortise 602 ull Surface - enter Pivot 611 ull Surface - Swing lear inish Stainless Steel US32 (630) Steel USP (600) Primed Length 83" 85" 95" 120" Other lengths available up to 120, consult factory. Handing is required. Options * PT lectric Power Transfer Prep * TW8 lectric Through Wire * TW4M, TW8M lectric Through Wire + Monitoring S Security asteners - Torx W Wood asteners * ull Mortise Models Only xterior Hardware 25

35 ontinuous Hinges 26 Pin and arrel Hinges - learance Requirements 1/8 Hinge Side learance 3/16 Hinge Side learance xterior Hardware Hinge Side learance 1/32 rame Irregularity SINL OOR oor Under-Sizing Hinge-Side Lock-Side rame eveled oor Square eveled Model learance learance Irregularity learance dged dged 600 1/4" 1/8" 1/32" 1/32" 13/32" 7/16" 602 1/8" 1/8" 1/32" 1/32" 9/32" 5/16" 700 1/4" 1/8" 1/32" 1/32" 13/32" 7/16" 702 1/8" 1/8" 1/32" 1/32" 9/32" 5/16" 705 3/8" 1/8" 1/32" 1/32" 17/32" 9/16" 705* 1/2" 1/8" 1/32" 1/32" 21/32" 11/16" 711 7/32" 1/8" 1/32" 1/32" 3/8" 13/32" 715 1/4" 1/8" 1/32" 1/32" 13/32" 7/16" * Use the djusta-studs with 705 1/16 rame Irregularity PIR O OORS oor Under-Sizing Square Square eveled eveled Hinge-Side Lock-Side rame eveled oor dged dged dged dged Model learance learance Irregularity learance Total ach oor Total ach oor 600 1/4" 3/16" 1/16" 1/16" 3/4" 3/8" 13/16" 13/32" 602 1/8" 3/16" 1/16" 1/16" 1/2" 1/4" 9/16" 9/32" 700 1/4" 3/16" 1/16" 1/16" 3/4" 3/8" 13/16" 13/32" 702 1/8" 3/16" 1/16" 1/16" 1/2" 1/4" 9/16" 9/32" 705 3/8" 3/16" 1/16" 1/16" 1" 1/2" 1-1/16" 17/32" 705* 1/2" 3/16" 1/16" 1/16" 1-1/4" 5/8" 1-5/16" 21/32" 711 7/32" 3/16" 1/16" 1/16" 11/16" 11/32" 3/4" 3/8" 715 1/4" 3/16" 1/16" 1/16" 3/4" 3/8" 13/16" 13/32" * Use the djusta-studs with

36 ontinuous Hinges ull Mortise Pin and arrel ontinuous Hinge or oors Weighing up to 600 pounds Non Handed 1/8 Inset 48" Maximum oor Width Non Handed evel or Square dge oor 27 Standard lengths 83", 85", 95", 120" Standard Mounting Hardware #10 X 1/2" Self rilling Self Tapping Screws, #10 X 1" Wood Screws Optional S - Security asteners vailable 3 / 8 1/8" 1 / 2 Material old-rolled Steel auge Type 304 Stainless Steel 1/4" iameter 304 Stainless Pin with Nylon Split earing inishes HM US Numbers USP US32 ustom Paint vailable, on 600 consult factory. 2-1/ H i n g e T h i c k n e s s ull Surface Pin and arrel ontinuous Hinge or oors Weighing up to 600 pounds Non Handed lush Mounted, No Inset 48" Maximum oor Width evel or Square dge oor Standard lengths 83", 85", 95", 120" Standard Mounting Hardware 1/4"-20 x 3/4" Self rilling Self Tapping Screws, over lips Optional S - Security asteners vailable Material old-rolled Steel auge Type 304 Stainless Steel 1/4" iameter 304 Stainless Pin with Nylon Split earing rushed luminum Leaf overs inishes HM US Numbers USP US32 ustom Paint vailable, on 602 consult factory 7/16 1/ 4 1-3/4 1-3/ Hinge Thickness 1/ 8 1 / 8 1 / 16 learance for Square dge 1-3 / 4 5/16" learance for eveled dge learance for Square dge 3 / / 4 5/32" learance for eveled dge 27 xterior Hardware

37 ontinuous Hinges Swing lear Pin and arrel ontinuous Hinge or oors Weighing up to 600 pounds Non Handed dge uard 48" Maximum oor Width Square dge oor Standard lengths 83", 85", 95", 120" Standard Mounting Hardware #10 X 1/2" Self rilling Self Tapping Screws #10 X 1" Wood Screws Optional S - Security asteners vailable Material old-rolled Steel auge Type 304 Stainless Steel 1/4" diameter 304 stanless pin with nylon split bearings inishes HM US Numbers USP US32 ustom Paint vailable, on 611 consult factory 1 / / 8 1-9/ ull Moritse, ull Wrap Pin and arrel ontinuous Hinge or oors Weighing up to 600 pounds Non Handed lush Mounted, No Inset 48" Maximum oor Width ull Wrap dge uard evel or Square dge oor H i n g e T h i c k n e s s 3 / 4 3 / / 4 7/32" 5 / learance for Square dge 1/4" learance for eveled dge xterior Hardware 28 Standard lengths 83", 85", 95", 120" Standard Mounting Hardware #10 X 1/2" Self rilling Self Tapping Screws, #10 X 1" Wood Screws djusta-stud 1-3/8" with internal thread Optional S - Security asteners vailable. Material 14 auge Type 304 Stainless Steel 1/4" diameter 304 stanless pin with nylon split bearings inishes HM 630 US Numbers US H i n g e T h i c k n e s s 2-1/4 1-7/8 Note: Provide djustment * djusta-stud allows up to 3/8 width adjustment which ensures proper alignment and easy installation. djusta-stud also makes it possible for future adjustments of the door on the frame through repositioning / 4 3 / / 4 3/16 3/ 8 3/8" learance for Square dge 13/32" learance for eveled dge

38 xterior Hardware ontinuous Hinges 715 ull Mortise, Half Wrap Pin and arrel ontinuous Hinge or oors Weighing up to 600 pounds Non Handed lush Mounted, No Inset Half Wrap dge uard 48" Maximum oor Width Square dge oor Standard lengths 83", 85", 95", 120" Standard Mounting Hardware #10 X 1/2" Self rilling Tek Screws, #10 X 1" Wood Screws Optional S - Security asteners vailable 29 Material 14 auge Type 304 Stainless Steel 1/4" diameter 304 stanless pin with nylon split bearings inishes HM / H i n g e T h i c k n e s s 3 / 8 US Numbers US32 ustom Paint vailable, consult factory 3 / 4 1/4" / 4 learance for Square dge 1-3 / 4 4/32" learance for eveled dge 29

39 ontinuous Hinges 30 lectrical utouts Ives Pin & arrel ontinuous Hinges are available with factory modified cutouts to accommodate most electrical frame to door requirements. Special templates are required. PT 600/700 TW 600/700 Top of door Top of door PT L TW L When ordering indicate the following: 1. Opening size. 2. Handing. LH, RH, RHR or LHR. 3. Manufacturer and model number of the electrical product being used. xample; Von uprin PT2 ecause clearances may vary between door and frame manufacturer, and locations can be influenced by the door hardware it is always recommend contacting Ives ustomer Technical for specific template information. or your general information following are standard locations for Von uprin PT2 or PT10, and TW (through wire) Standard centerline cutout locations rom Top dge o top of oor to enter Line of ut-out xterior Hardware Standard Length PT TW 83" 30" 43-19/32" 85" 32" 45-17/32" 95" 42" 55-17/32" 120" 67" 80-17/32" 30

40 Pivots The door rests on the bottom pivot in this application. This reduces the stress on the frame by distributing the weight of the door throughout the floor and structure. y taking advantage of the strength of the structure, this makes a pivot the ideal solution for your heavy doors. enter and pocket pivots also provide an aesthetic option for your opening. Pivots Table Of ontents page eneral Information Selection hart and Parts Reference How To Order /4" Offset V /4" Offset , /4" Offset /4" Offset , /4" Offset , /4" Offset /4" Offset /4" Offset /2" Offset /2" Offset V-7222 INT....Intermediate INT....Intermediate INT.Intermediate INT Intermediate INT Intermediate PT-7226PT-7227PT.Intermediate, lectrified enter Hung enter Hung J enter Hung enter Hung enter Hung Pocket Pivots xterior Hardware 31

41 Pivots Series Pivots eneral Information: omplete line of 3/4" offset, 1-1/2" offset, center hung, intermediate and power transfer pivots with all exposed parts made of brass or stainless steel for maximum corrosion resistance. High strength brass and stainless steel forgings, and castings for rated and non-rated doors combined with precision bearings for smooth operation. Stainless steel machine screws and wood screws standard. Positive locking vertical adjustment mechanism allows the installer to precisely position the door and balance the load. Last digit in pivot set number reflects the maximum door weight in hundreds of pound, e.g., 7215 = 500 pounds. or sets designated as heavy duty, add 1,000 pounds, e.g., 7237 H set = 1700 pounds. Pivots for lead lined doors are available, consult factory series Pivot Selection hart Pivot Pivot Type ottom Mounting UL Listing Max. oor Handing When Ordering Separate Parts Set Style Weight Top ottom Intermediate /4" Offset Jamb Mounted none 200 LH or RH TOP 7212 TM V-7222 INT 7212V 3/4" Offset Jamb Mounted none 200 LH or RH 7212V TOP 7212 TM V-7222 INT /4" Offset Jamb Mounted 20 Minute 500 LH or RH TOP 7215 TM INT /4" Offset Jamb Mounted 3 Hour 500 LH or RH TOP 7215 TM INT /4" Offset loor Mounted none 200 LH or RH TOP 7222 TM V-7222 INT /4" Offset loor Mounted 20 Minute 600 Non-Handed TOP 7226 TM INT /4" Offset loor Mounted 3 Hour 600 Non-Handed TOP 7226 TM INT /4" Offset Mortise ement ase 20 Minute 700 Non-Handed TOP 7227 TM INT /4" Offset Mortise ement ase 3 Hour 700 Non-Handed TOP 7227 TM INT /4" Offset loor Mounted 3 Hour 1,000 Non-Handed TOP 7230 TM INT xterior Hardware /4" Offset Mortise ement ase 3 Hour 1,750 Non-Handed TOP 7237 TM INT /2" Offset loor Mounted 3 Hour 400 Non-Handed TOP 7244 TM INT /2" Offset Mortise ement ase 3 Hour 500 Non-Handed TOP 7245 TM INT 7253 enter Hung loor Mounted none 300 Non-Handed J-7256 TOP 7253 TM INT 7255 enter Hung loor Mounted none 500 Non-Handed J-7256 TOP 7255 TM none 7255J enter Hung Jamb Mounted none 500 Non-Handed J-7256 TOP 7255J TM none 7256 enter Hung Mortise ement ase none 600 Non-Handed J-7256 TOP 7256 TM none 7259 enter Hung Mortise ement ase none 1,000 Non-Handed 7259 TOP 7259 TM none 32

42 Pivots How to Order: Pivot: V J Pivot Style: lank Top and bottom set TOP Top pivot only TM ottom pivot only INT Intermediate pivot only PT INT Power transfer intermendiate pivot only Hand: LH RH Left hand door Right hand door LH US3 33 inish: US3 US4 US10 US10 US26 US26 SP4 SP10 SP28 SP313 SPLK USP optional finishes are available, consult factory xterior Hardware 33

43 Pivots 34 xterior Hardware /4" Offset Pivot Handed Top, header mount ottom, jamb mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 200 pounds Vertical adjustment range 3/16", with positive locking Optional V-7222 Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 47. Meets NSI/HM V Pivot Set 7212V 3/4" Offset Pivot Handed Top, jamb mount ottom, jamb mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 200 pounds Vertical adjustment range 3/16", with positive locking Optional V-7222 Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page Plated inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number

44 Pivots /4" Offset Pivot Handed Top, header mount ottom, jamb mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 500 pounds Vertical adjustment range 3/16", with positive locking WP - optional weather resistant bottom pivot is modified for improved corrosion resistance. vailable in US26 (626) or US32 (630) only. 35 Meets NSI/HM Ul Listed 20 minute fire doors UL Listed 3 hour fire doors Optional or Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 47. Optional 7215PT Power Transfer, non-load bearing. See page Plated inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number Plated inishes steel US Number US3 US10 US32 US32 HM Number Painted inishes steel US Number SP4 SP10 SP28 SP313 SPLK HM Number xterior Hardware 35

45 Pivots 36 Meets NSI/HM /4" Offset Pivot Handed Top, header mount ottom, base plate mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 200 pounds Vertical adjustment range 3/16", with positive locking Optional V-7222 Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 47. xterior Hardware Plated inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number

46 Pivots /4" Offset Pivot Non-handed Top, header mount ottom, base plate mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 600 pounds Vertical adjustment range 3/16", with positive locking 37 Meets NSI/HM Ul Listed 20 minute fire doors UL Listed 3 hour fire doors Optional or Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 47. Optional 7226PT Power Transfer (four wires), non-load bearing. See page Plated inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number Plated inishes steel US Number US3 US10 US32 US32 HM Number Painted inishes steel US Number SP4 SP10 SP28 SP313 SPLK HM Number xterior Hardware 37

47 Pivots /4" Offset Pivot Non-handed Top, header mount ottom, base plate mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 700 pounds Vertical adjustment range 3/16", with positive locking Meets NSI/HM Ul Listed 20 minute fire doors UL Listed 3 hour fire doors Optional or Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 47. Optional 7227PT Power Transfer (four wires), non-load bearing. See page 49. xterior Hardware 7227 Plated inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number Plated inishes steel US Number US3 US10 US32 US32 HM Number Painted inishes steel US Number SP4 SP10 SP28 SP313 SPLK HM Number

48 xterior Hardware Pivots Meets NSI/HM UL Listed 3 Hour ire oors /4" Offset Pivot - Heavy uty Non-Handed Top, header mount ottom, base plate mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 1,000 pounds Vertical adjustment range 3/16", with positive locking Optional Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page Plated inishes steel US Number US3 US10 US32 US32 HM Number Painted inishes steel US Number SP4 SP10 SP28 SP313 SPLK HM Number

49 Pivots /4" Offset Pivot - Heavy uty Non-Handed Top, header mount ottom, mortised cement case mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 1,750 pounds Vertical adjustment range 3/16", with positive locking Optional Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 48. Meets NSI/HM UL Listed 3 Hour ire oors xterior Hardware Plated inishes steel US Number US3 US10 US32 US32 HM Number Painted inishes steel US Number SP4 SP10 SP28 SP313 SPLK HM Number

50 Pivots /2" Offset Pivot - Heavy uty Non-Handed Top, header mount ottom, base mount Use with 1-3/4" minimum door thickness Maximum door load 400 pounds Vertical adjustment range 3/16", with positive locking 41 Meets NSI/HM UL Listed 3 Hour ire oors Optional Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 48. Plated inishes steel US Number US3 US10 US32 US32 HM Number Painted inishes steel US Number SP4 SP10 SP28 SP313 SPLK HM Number xterior Hardware 41

51 Pivots /2" Offset Pivot - Heavy uty Non-Handed Top, header mount ottom, mortised cement case mount Use with 1-3/4" minimum door thickness, with 1/8" bevel in 2" Maximum door load 500 pounds Vertical adjustment range 3/16", with positive locking Optional Intermediate Pivot (handed) for each additional 100 pounds or doors over 7'. See page 48. Meets NSI/HM UL Listed 3 Hour ire oors xterior Hardware Plated inishes steel US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes steel US Number SP4 SP10 SP28 SP313 SPLK HM Number

52 Intermediate Pivots NP 80, Section requires intermediate pivot on some fire door applications, consult factory. Use for door heights over 7'0" and one every 2'6" or. Use for door weight over the pivot set limit. One additional for every additional 100 pounds. oor thickness 1-3/4" mimumum with 1/8" bevel in 2". 43 Meets NSI/HM V-7222 INT Use with 7212, 7212V or /4 Offset Pivot Handed Vertical adjustment 3/16", include positive locking INT: UL listed 20 minute fire doors Meets NSI/HM INT: UL listed 3 hour fire doors Meets NSI/HM INT Use with 7215, 7226 or /4 Offset Pivot Handed Vertical adjustment 3/16", include positive locking INT Use with 7215, 7226 or /4 Offset Pivot Handed Vertical adjustment 3/16", include positive locking. xterior Hardware 43

53 Intermediate Pivots xterior Hardware INT Use with 7230 or /4 Offset Pivot Handed Vertical adjustment 3/16", include positive locking. UL listed 3 hour fire doors Meets NSI/HM Use with 7244 or /2" Offset Pivot Handed Vertical adjustment 3/16", include positive locking. UL listed 3 hour fire doors Meets NSI/HM

54 Pivots 7215PT-7226PT-7227PT Power Transfer Pivot Use with 7215, 7226 or /4" Offset Pivots our wires, 28 guage Optional 8 wire available Rated 50 V or 3.5 amps. ontinuous or 16 amps pulse, maximum pulse 400 milliseconds. Non-load bearing Use with 1-3/4" thick door mimimum, 1/8" bevel in 2". 45 Plate inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number xterior Hardware 45

55 Pivots enter Hung Pivot Non-Handed Top, header mount ottom, base plate mount asy installation tilt on bearing and bearing pin. Use with 1-3/4" minimum door thickness. djustable floor to door clearance 3/16" to 3/4". Maximum door load 300 pounds Vertical adjustment range 3/16", with positive locking Plated inishes brass US Number US3 US4 US10 US10 US26 US26 Meets NSI/HM HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number xterior Hardware Radius Stop () to clear heel of door edge. Pivot distance () 1-3/4" (44mm) mimumum from jamb to centerline of pivot pin. Radius heel edge of door, 1-5/8" (41mm) mimumum recommended. learance from bottom edge of door to floor mounting surface is adjustable from 3/16" (5mm) to 3/4" (19mm) by varing the depth of the mortise ( ) in the bottom of the door, refer to hart. onsult factory when clearance is over 3/4" (19mm). Table learance epth of Mortise 3/16" (5mm) 1-3/16" (30mm) 3/8" (10mm) 1" (25mm) 1/2" (13mm) 7/8" (22mm) 5/8" (16mm) 3/4" (19mm) 3/4" (19mm) 5/8" (16mm) 46

56 Pivots 7255 enter Hung Pivot Non-Handed Top, header mount ottom, base plate mount asy installation tilt on bearing and bearing pin. Use with 1-3/4" minimum door thickness. djustable floor to door clearance 3/16" to 3/4", consultant factory if greater than 3/4".. Maximum door load 500 pounds Vertical adjustment range 3/16", with positive locking 47 Meets NSI/HM Radius Stop () to clear heel of door edge. Pivot distance () 1-3/4" (44mm) mimumum from jamb to centerline of pivot pin. Radius heel edge of door, 1-5/8" (41mm) mimumum recommended. learance from bottom edge of door to floor mounting surface is adjustable from 3/16" (5mm) to 3/4" (19mm) by varing the depth of the mortise ( ) in the bottom of the door, refer to hart. onsult factory when clearance is over 3/4" (19mm). Meets NSI/HM J enter Hung Pivot Non-Handed Top, header mount ottom, jamb mount asy installation tilt on bearing and bearing pin. Use with 1-3/4" minimum door thickness. djustable floor to door clearance 3/16" to 3/4", consult factory if greater than 3/4". Maximum door load 500 pounds Vertical adjustment range 3/16", with positive locking xterior Hardware 47

57 Pivots enter Hung Pivot Non-Handed Top, header mount ottom, base frame mount asy installation tilt on bearing and bearing pin. Use with 1-3/4" minimum door thickness. djustable floor to door clearance 3/16" to 3/4", consult factory if greater than 3/4". Maximum door load 600 pounds Vertical adjustment range 3/16", with positive locking Meets NSI/HM xterior Hardware Radius Stop () to clear heel of door edge. Pivot distance () 1-3/4" (44mm) mimumum from jamb to centerline of pivot pin. Radius heel edge of door, 1-5/8" (41mm) mimumum recommended. learance from bottom edge of door to floor mounting surface is adjustable from 3/16" (5mm) to 3/4" (19mm) by varing the depth of the mortise ( ) in the bottom of the door, refer to hart. onsult factory when clearance is over 3/4" (19mm). Table learance epth of Mortise 3/16" (5mm) 1-3/16" (30mm) 3/8" (10mm) 1" (25mm) 1/2" (13mm) 7/8" (22mm) 5/8" (16mm) 3/4" (19mm) 3/4" (19mm) 5/8" (16mm) Plated inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number

58 Pivots 7259 enter Hung Pivot Non-Handed Top, header mount ottom, base frame mount asy installation tilt on bearing and bearing pin. Use with 2" minimum door thickness. djustable floor to door clearance 3/16" to 3/4", consult factory if greater than 3/4". Maximum door load 1,000 pounds Vertical adjustment range 3/16", with positive locking 49 Meets NSI/HM Radius Stop () to clear heel of door edge. Pivot distance () 1-3/4" (44mm) mimumum from jamb to centerline of pivot pin. Radius heel edge of door, 1-5/8" (41mm) mimumum recommended. learance from bottom edge of door to floor mounting surface is adjustable from 3/16" (5mm) to 3/4" (19mm) by varing the depth of the mortise ( ) in the bottom of the door, refer to hart. onsult factory when clearance is over 3/4" (19mm). Table learance epth of Mortise 3/16" (5mm) 1-3/16" (30mm) 3/8" (10mm) 1" (25mm) 1/2" (13mm) 7/8" (22mm) 5/8" (16mm) 3/4" (19mm) 3/4" (19mm) 5/8" (16mm) Plated inishes brass US Number US3 US4 US10 US10 US26 US26 HM Number Painted inishes brass US Number SP4 SP10 SP28 SP313 SPLK HM Number xterior Hardware 49

59 Pivots 50 UL Listed 3 hour fire doors or 20 minute wood fire doors 91105, PT Pocket Pivot/Hinge Non-handed ll stainless steel construction. llows door to open a full 90 (* degree mark) ull mortise 90 pound load bearing Use two for doors up to 7'0" and over 7'0" use three. PT, Power Transfer version has four 28 guage wires. Rated 50 VO or 3.5 amps. ontinuous or 16 amps pulse. Maximum pulse 400 milliseconds Pocket Pivot Meets NSI/HM Pocket Pivot 1-3/8 utout 1-1/8 1-9/64 1-9/ /32 xterior Hardware oor Portion L of oor 1-1/8 Plated inishes steel US Number US3 US10 US10 HM Number Jamb Portion Painted inishes steel US Number USP SP313 HM Number inishes stainless steel US Number US32 US32 HM Number

60 Table Of ontents Pulls, Plates and Trim Pulls page 8102 oor Pull oor Pull Z oor Pull oor Pull oor Pull oor Pull oor Pull Offset oor Pull Push and Pull Plates 8200 Push Plate Pull Plate (less pull) Pull Plate Pull Plate Pull Plate (with 8105) Pull Plate (with ) Push ars 9100 Pushbar Z Pushber & Pull Pushbar & Pull Vandal Resistant Trim VR810-T, VR814T Vandal Resistant Trim VR810-NL, VR814-NL Vandal Resistant Trim VR900, VR904 Vandual Resistant Trim VR900LLP, VR904LLP Vandual Resistant Trim VR910-T, VR914-T Vandual Resistant Trim VR910-NL, VR914-NL Vandual Resistant Trim VR910M-T, VR914M-T Vandual Resistant trim VR910M-NL, VR914M-NL Vandual Resistant Trim Protection Plates 8400 Protection Plate Protection Plate (UL) Mounting etail Special Mounting etail xterior Hardware 1

61 rchitectural oor Trim 2 xterior Hardware 3/4 ROUN 1 ROUN 8102 oor Pull - 3/4" Round vailable mounting standard,, H-I-L, orj see pages 15 and 16 vailable Sizes 6", 8", 10" Projection enter to enter Overall Length Product No. learance /4" 1-1/2" 6" 6-3/4" /4" 1-1/2" 8" 8-3/4" /4" 1-1/2" 10" 10-3/4" inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32* HM 630 inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 8103 oor Pull - 1" Round vailable mounting standard,, H-I-L, or J see pages 15 and 16 vailable Sizes 8", 10", 12" Projection enter to enter Overall Length Product No. learance /2" 1-1/2" 8" 9" /2" 1-1/2" 10" 11" /2" 1-1/2" 12" 13" inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32 US32* HM inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 2

62 rchitectural oor Trim 2-1/2 LRN 1 ROUN 1 LTT 1/2 ROUN 8103Z oor Pull - 1 Round Large 2-1/2" learance for the ccessibility pplications vailable mounting standard, M, O, H-I-L, J see pages 15 and 17 vailable Sizes 8", 10", 12" Projection enter to enter Overall Length Product No. learance 8103Z 3-1/2" 2-1/2" 8" 9" 8103Z 3-1/2" 2-1/2" 10" 11" 8103Z 3-1/2" 2-1/2" 12" 13" inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32 US32* HM inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 8105 oor Pull - 1 lattened vailable mounting standard or see page 15 vailable Sizes 6", 8", 10" Projection enter to enter Overall Length Product No " 6" 6-1/2" " 8" 8-1/2" " 10" 10-1/2" inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32* HM 630 inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 3 3 xterior Hardware

63 rchitectural oor Trim oor Pull vailable mounting standard see page 15 Size 5-1/4" Projection enter to enter Overall Length Product No /16" 5-1/4" 6-1/4" 1 ROUN S inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32* HM 630 inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M oor Pull Standard sheet metal screws for surface mounting Size 5-1/4" Projection enter to enter Overall Length Product No /16" 5-5/8" 7-1/2" inishes brass US Number US26* HM 626 * vailable with ntimicrobial oating, use suffix M xterior Hardware 1-7/8 SUR MOUNT 4

64 rchitectural oor 8121 oor Pull vailable mounting K see page 16 Size 5-3/4" Projection enter to enter Overall Length Product No /2" 5-3/4" 8-3/4" inishes brass US Number US26* HM /2 HOSPITL * vailable with ntimicrobial oating, use suffix M Offset oor Pull vailable mounting standard H-I-L,M, N or O see page 15 and 17 vailable Sizes 8", 10", 12", 18" 1 ROUN Projection enter to enter Overall Length Product No. learance /4" 2-1/4" 8" 9" /4" 2-1/4" 10" 11" /4" 2-1/4" 12" 13" /4" 2-1/4" 18" 19" inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32 US32* xterior Hardware HM * vailable with ntimicrobial oating, use suffix M 5

65 rchitectural oor Trim Push Plate 8300 Pull Plate, Prep for Pull (less pull) vailable Sizes 3" x 12" 3.5" x 15" 4" x 16" 6" x 16" 8" x 16" Special sizes are available. onsult factory. 2 2 Plates ut for ylinder or Thumbturns Plates are available with cutout for cylinder or thumbturn; standard cutout is 2 from top and centered on plates up to 4 wide. or plates wider than 4 cutout is located 2 from outer edge, specify LH or RH. When pull location interferes with standard cutout location a detail drawing should be furnished with the order. 2 2 T 2 2 Standard cutout is 1-1/4 for cylinder and 3/8 for thumbturn. Specify for cutout for cylinder or T for cutout for thumbturn. T inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32* HM 630 xterior Hardware inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 6

66 rchitectural oor Trim 3/4 ROUN 1 ROUN 1 LTT 1/2 ROUN 8302 Pull plate vailable mounting Standard,,, H-I-L, or J see pages 15 and Plate 8102 Pull 3-1/2" x 15" 6" centers 4" x 16" 8" centers 6" x 16" 10" centers inishes brass US Number US3 US4 US10 US10 US26 US26* HM inishes stainless steel US Number US32* HM 630 inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 8303 Pull plate vailable mounting Standard,,, H-I-L, or J see pages 15 and Plate 8103 Pull 3-1/2" x 15" 8" centers 4" x 16" 10" centers 6" x 16" 7" centers inishes brass US Number US3 US4 US10 US10 US26 US26* HM inishes stainless steel US Number US32* HM 630 inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 8305 Pull plate vailable mounting Standard or see page Plate 8105 Pull 3-1/2" x 15" 6" centers 4" x 16" 8" centers 6" x 16" 10" centers inishes brass US Number US3 US4 US10 US10 US26 US26 HM inishes stainless steel US Number US32 HM 630 inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 7 xterior Hardware 7

67 rchitectural oor Trim 8 1 ROUN S 8311 Pull plate vailable mounting Standard or see page Plate Pull 3-1/2" x 15" 5-1/8" centers 4" x 16" 6" x 16" inishes brass US Number US3 US4 US10 US10 US26 US26* HM inishes stainless steel US Number US32* HM 630 inishes aluminum US Number US28 HM 628 * vailable with ntimicrobial oating, use suffix M 9100 Series oor Push ars and Pulls vailable in brass, stainless steel or aluminum. Standard fasteners furnished for 1-3/4 thick doors. Specify door thick if other than standard. Special lengths are available, contact customer service. See page 17 for special mounting requirements. aution the length of the pushbar should not interfere with the door jamb or cause a pinch point Push ar vailable mounting NO or NS see page 17 xterior Hardware 1 ROUN Product No. Projection learance enter to enter Overall Length /2" 1-1/2" 28" 29" /2" 1-1/2" 33" 34" Special lengths available, consult factory inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32 US32* HM * vailable with ntimicrobial oating, use suffix M 8

68 rchitectural oor Trim 1 ROUN 9103Z Straight Pull/Pushbar ombo (8103Z Pull Push) vailable mounting NO or NS see page 17 Projection Product No. T Push T Pull Push & Pull 9103Z 28", 33" 8" 2-1/2" & 3-1/2" 9103Z 28", 33" 10" 2-1/2" & 3-1/2" 9103Z 28", 33" 12" 2-1/2" & 3-1/2" Special lengths available, consult factory inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32 US32* HM * vailable with ntimicrobial oating, use suffix M 9 1 ROUN 9190 Offset Pull/Pushbar ombo (8190 pull push) vailable mounting NO or NS see page 17 Projection Product No. T Push T Pull Push & Pull ", 33" 8" 2-1/2" & 3-1/4" ", 33" 10" 2-1/2" & 3-1/4" ", 33" 12" 2-1/2" & 3-1/4" ", 33" 18" 2-1/2" & 3-1/4" Special lengths available, consult factory inishes brass US Number US3 US4 US10 US10 US15 US26 US26* HM inishes stainless steel US Number US32 US32* HM * vailable with ntimicrobial oating, use suffix M xterior Hardware 9

69 Vandal Resistant Trim Vandal Resistant Trim ll stainless steel, 11 gauge (0.120 thick), using stainless steel fasteners for door thickness of 1-3/4 to 2-1/4. uilt-in lock protector prevents tampering on certain models. Protective cylinder collar spins to reduce damage from pipe wrench or other tools. Models are available with or without attractive black plastisol edge grip. 10 VR810-T VR814-T With black grip Without black grip or use with Monarch XX, 18 Series or 25 Series rim exit device Non-handed Thru-bolts direct to the exit device Pull operation only VR814 VR810 Prod. Thru-olt learance No. Width Height Pattern rip to oor Projection VR810T 5-1/4" 11" 1-3/4" Wide x 7-3/4" High 1-1/2" 1-7/8" inishes US inish US32 HM 630 VR810-NL VR810-NL VR814-NL VR814-NL LHR With black grip RHR With black grip LHR Without black grip RHR Without black grip or use with Monarch XX-V, 18-V Series or 25-V Series vertical rod exit device Thru-bolts direct to the exit device Night latch operation (cylinder not furnished) Prod. Thru-olt learance No. Width Height Pattern rip to oor Projection VR810NL 5-1/4" 11" 1-3/4" Wide x 7-3/4" High 1-1/2" 1-7/8" xterior Hardware inishes US inish US32 HM

70 Vandal Resistant Trim VR900 RHR With black grip VR900 LHR With black grip VR904 RHR Without black grip VR904 LHR Without black grip or use with most mortise locks on outswinging doors including Schlage L9000 Series with interior L or N escutcheon, and rose trim. Includes built-in lock protector and cylinder cutout. Handed design allows trim to be positioned to coordinate with the centerline of inside hardware. Thru-olt learance Width Height Pattern rip to oor Projection 7-1/4" 11" 2" Wide x 10" High 1-1/2" 1-7/8" inishes US inish US32 HM 630 VR900LLP RH With black grip VR900LLP LH With black grip VR904LLP RH Without black grip VR904LLP LH Without black grip or use with most mortise locks on outswinging doors including Schlage L9000 Series with interior L or N escutcheon, and rose trim. Includes built-in lock protector and cylinder cutout. Handed design allows trim to be positioned to coordinate with the centerline of inside hardware. Thru-olt learance Width Height Pattern rip to oor Projection 5-1/4" 11" 1-3/4" Wide x 10" High 1-1/2" 1-7/8" inishes US inish US32 HM xterior Hardware 11

71 Vandal Resistant Trim 12 VR910-T VR914-T With black grip Without black grip or use with Von uprin 98/99 Series rim and vertical rod exit device Non-handed Thru-bolts direct to the exit device Pull operation only. Thru-olt learance Width Height Pattern rip to oor Projection 5-1/4" 11" 1-3/8" Wide x 7" High 1-1/2" 1-7/8" inishes US inish US32 HM 630 VR910-NL VR914-NL With black grip Without black grip or use with Von uprin 98/99 rim and vertical rod exit device Non-handed Thru-bolts direct to the exit device Thru-olt learance Width Height Pattern rip to oor Projection 5-1/4" 11" 1-3/8" Wide x 7" High 1-1/2" 1-7/8" inishes US inish US32 HM 630 VR910M-T With black grip VR914M-T Without black grip or use with Von uprin 9875/9975 mortise lock exit device Non-handed Thru-bolts direct to the exit device Thru-olt learance Width Height Pattern rip to oor Projection 7-1/4" 11" 1-3/8" Wide x 7" High 1-1/2" 1-7/8" inishes US inish US32 HM 630 xterior Hardware 12 VR910M-NL RHR With black grip VR910M-NL LHR With black grip VR914M-NL RHR Without black grip VR914M-NL LHR Without black grip or use with Von uprin 9875/9975 Series mortise lock exit device Thru-bolts direct to the exit device Night latch operation (cylinder not furnished) Thru-olt learance Width Height Pattern rip to oor Projection 7-1/4" 11" 1-3/8" Wide x 7" High 1-1/2" 1-7/8" inishes US inish US32 HM 630

72 Protection Trim 8400 Series Protection Plates oor protection plates are available in.050 thick brass, stainless steel or aluminum; and 1/8 thick high impact polyethylene in clear or black. evel edge options; specify 4 for all four edges. Mounting screw pack furnished standard, 16 screws per pack. Optional screw packs are available for TK or TORK screw heads. Refer to the following chart for ordering. Specify NMH for no mounting holes. Specify NMH- for no mounting holes with adhesive. Specify S for counter sunk mounting holes. Specify RS prepped with extra row of screws. Kickplate asket Tape Tape is recommended when using a brass plate on a metal door to reduce tarnishing from electrolytic oxidation. One tape pack will cover an the perimeters of a 8 x 34 kickplate. Order 8401 asket Tape Protection Plate 8402 (UL)* Protection Plate *UL mark appears in upper right corner. Number of screw packs required by plate size (specify TK Screws or TORK screws). 22"-25" 26"-33" 34"-41" 42"-48" 4"-8" "-16" "-24" "-32" "-40" "-48" inishes brass US Number US3 US4 US10 US10 US15 US26 US26 HM inishes stainless steel US Number US32 US32 HM xterior Hardware inishes aluminum US Number US28 HM 628 inishes plastic lear and lack Residential rade Kickplates available arded only, finishes P28, P3, P619, P716, 3, 505, 619,

73 Protection Trim xterior Hardware 14 Mop Plates Protect the bottom of the pull side of door subject to cleaning and mopping procedures. Size Ranges:4" to 6" high, 22" to 48" wide Kick Plates Protect the bottom of the push side of doors subject to scuffing from foot traffic. Recommended for all doors subject to normal use (especially doors using a closer). Size Ranges: 8" to 24" high, 22" to 48" wide Stretcher Plates Protect doors at specific areas where consistent contact is made by stretchers, service carts or other equipment. Usually applied to push side of doors. Specify 4 Option for beveled edges. Size Ranges: 6" to 8" high, 22" to 48" wide rmor Plates Protect lower half of doors from abuse by hard carts, trucks and rough usage. Usually applied to push side of single doors and both sides of double acting doors. Size Ranges: 26" to 48" high, 22" to 48" wide 14

74 Push Plates Mounting ll mounting hardware is for standard 1-3/4" door. onsult ustomer Service if other than standard. Standard Mount Type Mount 15 Standard Mounting (2) 1/4-20 x 2-1/4" brass, oval head machine screws; plated to match. (2) No. 14 countersunk washers; plated to match Type Mount oncealed Pull Plate Mounting vailable only for 8302, 8303, 8311 Pull Plates. (2) 1/4-20 x 5/8" steel flat head machine screws; zinc plated. Pull mounts directly onto plate. Plate is attached to door by 6 screws. Type H-I-L Mount Wood oors oncealed Pull Mounting With Push Plate (2) 1/4-20 x 2-1/4" steel flat head machine screws; zinc plated. vailable only for 8102, 8103, 8105, 8111, 8302, 8303, 8305 and Plate on opposite side of door must be ordered separately. Reinforced Hollow Metal oor oncealed Pull Mounting vailable only for , 8103Z or wood door Pulls and 8302, 8303 pull plates. (2) Steel screw sleeves; zinc plated. (2) 1/4-20 x 1-1/4" steel countersunk trim head machine screw; zinc plated for reinforced metal door. (2) 1/4 x 1-1/2" steel countersunk trim head steel metal screw; zinc plated for wood doors. xterior Hardware 15

75 rchitectural oor Trim 16 xterior Hardware Mounting ll mounting hardware is for standard 1-3/4" door. onsult ustomer Service if other than standard. Type J Mount Type K Mount ack to ack Pull Mounting vailable only for 8102, 8103, Pulls and 8302, 8303 Pull plates. (2) Steel screw sleeves; zinc plated. (2) 1/4-20 x 2-3/4" steel countersunk trim head machine screws; zinc plated. Pulls furnished in pairs (PR) unless single (SL) specified. ack to ack Pull Mounting vailable only for Pulls. (4) Steel screw sleeve nuts; steel zinc plated. (8) No x 1" brass oval head machine screws; plated to match. Pulls furnished in pairs (PR). 16

76 rchitectural oor Trim Mounting for 8103Z, 8190, 9100, 9103Z and 9190 ll mounting hardware is for standard 1-3/4" door. onsult ustomer Service if other than standard. Type M Mount Type O Mount RH (M1) and LH (M2) Thread 17 ack-to-ack with Spanner ollar Pulls furnished in pairs (PR) or Single (SL) must specify M1 or RH thread or M2 for LH thread. Type N Mount ecorative lind Thru - olt Type NO Push/Pull Mounting Type N & Type O Pushbar to Pull - (1) 1/4-20 X 3"steel countersunk trim head machine screws with (2) set screws. - (1) steel screw sleeve, zinc plated. ree nd Pushbar & Pull - (2) 1/4-20 X 2-1/4" blind thru-bolts; plated to match. (push) ack-to-ack Two-nchor (pull) Type NS-Standard Push/Pull Mounting Type N & Standard Pushbar to Pull - (1) 1/4-20 X 3"steel countersunk trim head machine screws with (2) set screws. - (1) steel screw sleeve, zinc plated. ree nd Pushbar & Pull - (2) 1/4-20 X 2-1/4" brass, oval head mach screws; plated to match. - (2) No. 14 countersunk washers; plated to match. xterior Hardware 17

77 Notes 18 xterior Hardware 18

78 xterior Hardware lush olts and oordinators Table Of ontents lush olts page 31, 32, 33 utomatic lush olt , 42 utomatic lush olt , 52, 53 utomatic lush olt , 62 onstant Latching lush olt Manual lush olt Manual lush olt Manual lush olt Manual lush olt Manual lush olt Manual lush olt P1, P2 ust Proof Strike oordinators OR Series ar oordinator L Series iller bar M1, M2 Mounting rackets M1, M2, M3 Mounting rackets M1V, M2V, M3V Mounting rackets OR7, OR ravity oordinator arry ar How to order Special factory prep

79 utomatic lush olts Metal oors 31P Top and ottom olts (Pair) ully utomatic inactive door is latched, bolts are extended when active door closes, door is unlatched, bolts retract when active door is opened. Low ctuation orces Top olt Has No Spring Tension. its standard NSI oor rame Preparations. Non-handed. olt throw is 3/4" with a 7/8" vertical adjustment. olt backset is 3/4" Standard Rod Length is 12", which is measured from the center of the flush bolt body to the bolt tip. Optional rod lengths available for top bolt only on non-fire rated openings 18", 24", 36" and 48. P1 or P2 optional dust proof strike available, see page Top olt ottom olt Meets NSI Type 25. UL Listed 3 Hour ire oors 8'0" x 10'0" 31T Top olt Only ottom olt Only Top olt with uxiliary ire Latch 32 Model with uxiliary ire Latch eliminates the bottom bolt and is UL Listed for ire oors. Top olt with uxiliary ire Latch and Retrofit Plate 33 Model with uxillary ire Latch eliminates the bottom bolt and includes a retrofit plate to cover existing bottom bolt prep. UL Listed for ire oors. xterior Hardware Top olt uxiliary ire Latch Meets NSI Type 25. UL Listed 3 Hour ire oors 8'0" x 10'0" ody Size: 1" Wide x 6-3/4" Long x 2" eep uide Size: 1" Wide x 1-27/32" Long x 27/32" High x 3/32" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick uxiliary ire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" eep Retrofit Plate Size: 1" Wide x 6-3/4" Long x 3/32" Thick inishes Ives Number US3 US4 US10 US10 US32 US32 HM

80 utomatic lush olts Wood oors Top olt ottom olt Meets NSI Type 25. UL Listed 90 Minute ire oors 8'0" x 8'0" 41P Top and ottom olts (Pair) ully utomatic inactive door is latched, bolts are extended when active door closes, door is unlatched bolts retract when active door is opened. Low ctuation orces Top olt Has No Spring Tension. Non-handed. olt throw is 3/4" with a 7/8" vertical adjustment. olt backset is 3/4" P1 or P2 optional dust proof strike available, see page T 41 Top olt Only ottom olt Only 42 Top olt with uxiliary ire Latch 42 Model with uxiliary ire Latch eliminates the bottom bolt and is UL Listed for ire oors. 3 Top olt uxiliary ire Latch ody Size: 1" Wide x 8-1/2" Long x 2" eep uide Size: 1" Wide x 6" Long x 1/8" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick uxiliary ire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" eep Meets NSI Type 25. UL Listed 20 Minute ire oors 8'0" x 8'0" inishes Ives Number US3 US4 US10 US10 US32 US32 HM xterior Hardware 3

81 onstant Latching lush olts Metal oors 4 Top olt ottom olt Meets NSI Type 27. UL Listed 3 Hour ire oors 8'0" x 10'0" 51P Top and ottom olts (Pair) onstant Latching inactive door remains latched until the active door is opened, releasing the automatic bottom bolt and then the top bolt can be manually released. Inactive door will relatch automatically when closed. Low ctuation orces. its standard NSI oor and rame Preparations. Non-handed. 3/4" bolt throw with a 7/8" vertical adjustment. 3/4" backset Standard Rod Length is 12", which is measured from the center of the flush bolt body to the bolt tip. Optional rod lengths available for top bolt only on non-fire rated openings 18", 24", 36" and 48". P1 or P2 optional dust proof strike available, see page T Top olt Only Top olt with uxiliary ire Latch 52 Model with uxiliary ire Latch eliminates the bottom bolt and is UL Listed for ire oors. Top olt with uxiliary ire Latch & Retrofit Plate 53 Model with uxiliary ire Latch eliminates the bottom bolt and includes a retrofit plate to cover existing bottom bolt prep. UL Listed for ire oors. xterior Hardware Top olt uxiliary ire Latch Meets NSI Type 27. UL Listed 3 Hour ire oors 8'0" x 10'0" ody Size: 1" Wide x 6-3/4" Long x 2" eep uide Size: 1" Wide x 1-27/32" Long x 11/16" High x 3/32" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick uxiliary ire Latch Size: 1" Wide x 1-3 4" Long x 3-1/4" eep Retrofit Plate Size: 1" Wide x 6-3/4" Long x 3/32" Thick inishes Ives Number US3 US4 US10 US10 US32 US32 HM

82 onstant Latching lush olts Wood oors Top olt ottom olt Meets NSI Type 27. UL Listed 90 Minute ire oors 8'0" x 8'0" Top olt uxiliary ire Latch Meets NSI Type 27. UL Listed 20 Minute ire oors 8'0" x 8'0" 61P Top and ottom olts (Pair) onstant Latching inactive door remains latched until the active door is opened, releasing the automatic bottom bolt and then the top bolt can be manually released. Inactive door will relatch automatically when door closes. Low ctuation orces. Non-handed. olt throw is 3/4" with a 7/8" vertical adjustment. olt backset is 3/4" P1 or P2 optional dust proof strike available, see page T 62 Top olt Only Top olt with uxiliary ire Latch 62 Model with uxiliary ire Latch eliminates the bottom bolt and is UL Listed for ire oors.. ody Size: 1" Wide x 8-1/2" Long x 2" eep uide Size: 1" Wide x 6" Long x 1/8" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 1/16" Thick Rub Plate Size: 1-1/4" Wide x 1-11/16" Long x 3/64" Thick uxiliary ire Latch Size: 1" Wide x 1-3/4" Long x 3-1/4" eep inishes Ives Number US3 US4 US10 US10 US32 US32 HM xterior Hardware 5

83 Manual lush olts 6 xterior Hardware Meets NSI/HM , L lush olt n exceptionally smooth working flush bolt with sharp, crisp lines. ouble action spring design provides automatic holding of brass bolt in projected or retracted position, and assures ease of operation in conjunction with deep cup finger hole. Made from polished cast brass. olt tip is 5/16" iameter olt throw is 3/4" olt backset is 15/32" ody Size: 3/4" Wide x 4" Long x 1-1/8" eep Strike Size: 5/8" Wide x 1-1/2" Long inishes Ives Number HM lush olt n exceptionally smooth working flush bolt with sharp, crisp lines. ouble action spring design provides automatic holding of brass bolt in projected or retracted position, and assures ease of operation in conjunction with deep cup finger hole. Made from polished cast brass. olt tip is 1/2" iameter olt throw is 1" olt backset is 15/32" ody Size: 3/4" W x 6" L x 1-11/32" Strike Size: 7/8" W x 1-3/4" L Meets NSI/HM , L inishes Ives Number HM

84 Manual lush olts Meets NSI/HM , L lush olt flush bolt with radiused bottom faceplate designed specifically for simple one-step router installation. ouble action spring design provides automatic holding of brass bolt in projected or retracted position, and assures ease of operation in conjunction with deep cup finger hole. aceplate is polished solid brass; bolt is made from aluminum zinc alloy. olt tip is 1/2" iameter olt throw is 1" olt backset is 1/2" ody Size: 3/4" W x 6" L x 1-7/16" Strike Size: 7/8" W x 1-3/4" L inishes Ives Number HM xterior Hardware 7

85 Manual lush olts Wood oors 8 Meets NSI/HM , L UL Listed 90 Minute ire oors 8'0" x 10'0" 358 Top or ottom olts When the active door is opened, the lever can be moved to the up position, retracting the bolt and allowing the inactive leaf to be opened. When the inactive leaf is closed, the lever can be moved to the down position, projecting the bolt into the strike and securely locking the inactive leaf. Reduces installation costs; requires only simple router mortise at top and bottom corners of doors. oor strength and rigidity maintained by tying door faces to reinforcing extensions on guide with machine screws and bearing washers, not supplied. Non-handed. olt tip 1/2" diameter olt throw is 3/4" with a 7/8" vertical adjustment. olt backset is 3/4" Not available for rabbeted door installations. P1 or P2 optional dust proof strike available, see page 11. ody Size: 1" Wide x 6-3/4" Long x 1-3/8" eep uide Size: 1" Wide x 2-1/2" Long x 5/64" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick inishes Ives Number US3 US4 US10 US10 US15 US26 US26 HM xterior Hardware 8

86 xterior Hardware Manual lush olts Metal oors Meets NSI/HM , L UL Listed 3 Hour ire oors 8'0" x 10'0" 457 Top or ottom olts When the active door is opened, the lever can be moved to the up position, retracting the bolt and allowing the inactive leaf to be opened. When the inactive leaf is closed, the lever can be moved to the down position, projecting the bolt into the strike and securely locking the inactive leaf. Simplified installation in metal frames. Round bolt head requires only a punched hole. Use of strike optional. Special design of guide and flat sided bolt tip to prevent bolt rotation. Non-handed. olt tip is 1/2" iameter. olt throw is 3/4" with a 7/8" vertical adjustment. olt backset is 3/4" Standard Rod Length is 12", which is measured from the center of the flush bolt body to the bolt tip. Optional rod lengths available - 6", 9", 18" and 24" for fire rated doors. Optional rod lengths available - 6", 9", 18", 24", 30", 36" and 48" for non-fire rated doors. P1 or P2 optional dust proof strike available, see page ody Size: 1-1/4" Wide x 6-3/4" Long x 1-1/8" eep uide Size: 1" Wide x 2" Long x 5/64" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick inishes Ives Number US3 US4 US10 US10 US15 US26 US26 HM

87 Manual lush olts Metal oors 10 Meets NSI/HM , L UL Listed 90 Minute ire oors 8'0" x 10'0" 458 Top or ottom olts When the active door is opened, the lever can be moved to the up position, retracting the bolt and allowing the inactive leaf to be opened. When the inactive leaf is closed, the lever can be moved to the down position, projecting the bolt into the strike and securely locking the inactive leaf. Simplified installation in metal frames. Round bolt head requires only a punched hole. Use of strike optional. Special design of guide and flat sided bolt tip to prevent bolt rotation. Non-handed. olt tip is 1/2" diameter. olt throw is 3/4" with a 7/8" vertical adjustment. olt backset is 3/4" Standard Rod Length is 12", which is measured from the center of the flush bolt body to the bolt tip. Optional Rod Lengths available - 6", 9", 18" and 24" for fire rated oors. Optional Rod lengths available - 6", 9", 18", 24", 30", 36" and 48" for non-fire rated doors. P1 or P2 optional dust proof strike available, see page 11. ody Size: 1" Wide x 6-3/4" Long x 1-1/8" eep uide Size: 1" Wide x 2" Long x 5/64" Thick Strike Size: 15/16" Wide x 2-1/4" Long x 5/64" Thick inishes Ives Number US3 US4 US5 US10 US10 US15 US26 US26 HM xterior Hardware 10

88 xterior Hardware ust Proof Strikes P1 P2 Meets Meets NSI/HM , L P1 P2 ust Proof Strikes esigned for use with the bottom bolt of all flush bolts. Spring-loaded plunger returns to floor or threshold level anytime flush bolt is retracted, eliminating need to clean standard floor strikes. Strike hole is 3/4" iameter and 1-1/8" eep P1 ace Plate: 1-7/16" iameter P2 ace Plate: 1-5/8" W x 3-1/2" L x 1/8" Thick ody: 1-3/16" iameter x 1-7/8" eep inishes Ives Number US3 US4 US10 US10 US26 US26 HM

89 oordinators ar oordinators and iller ars 12 Meets NSI/HM 156.3, Type 21. UL Listed for installation on labeled frame. OR or Openings Where oors re Same Size oordinator Length of or Opening ommon Number hannel Widths pplications OR32 32" 34" - 52" Pair of 2'0" oors OR42 42" 52" - 72" Pair of 2'6" oors OR52 52" 62" - 92" Pair of 3'0" oors OR60 60" 70" - 108" Pair of 3'6" oors OR72 72" 84" - 132" Pair of 4'0" oors or Openings Where oors re Unequal Size The coordinator length should equal the active door width plus approximately 1/2 the inactive door width. The coordinator must be 6" longer than the active door width and shorter than the overall frame opening between stops. L Series ar oodinators The OR Series oordinators are designed for use on pairs of doors when one door needs to close before the other. ll OR units function easily. The active door lever, located nearest to the active stop, holds the active door open until the trigger mechanism is released by the closing of the inactive leaf. ll OR units may not function correctly with swingclear hinges. ll OR units are equipped with an adjustable override feature which allows the active door to close under extreme pressure. ll OR units are compatible with lush olts. The OR Series is available in five sizes for variable door opening widths. The OR Series does not cover the entire length of the stop, so a L filler bar can be provided to maintain architecturally clean lines. OR Series oordinator hannels and L fillers are made of aluminum. Optional iller ars: L20-20", L32-32" and L44-44", available to maintain clean line. Optional Mounting rackets available: M1, M2, M1, M2, M3, M1V, M2V, and M3V for other stop applied hardware. inishes Ives inish US28 US26 315N HM Series iller ars The L iller ars are available in three sizes for variable frame openings. L iller ars are made of aluminum L iller ars are field sized to frame opening. iller ar Number Length xterior Hardware L20 20" 1-5/8" W x 5/8" x 20" L L32 32" 1-5/8" W x 5/8" x 32" L L44 44" 1-5/8" W x 5/8" x 44" L inishes Ives inish US28 US26 315N HM

90 oordinators Mounting rackets M1and M2 Mounting rackets llows stop mounted hardware to be properly installed without damaging the OR coordinator, such as a parallel arm closer or a non-fire-rated surface vertical rod strike. Stop mounted hardware will need to be lowered to compensate for the height of the coordinator and mounting bracket. M mounting brackets are made of aluminum Product Jamb epth Stop Width M1 4-3/4" Min. Over 2-1/2" 4" W x 3" x 15/16" T M2 4-3/4" Min. Up to 2-1/2" 4" W x 3-1/4" x 1-5/8" T inishes Ives inish USP SP28 SPLK M1V M1, M2 and M3 M1V, M2V and M3V M2V HM ire Rated Mounting rackets llows for fire-rated stop mounted hardware to be properly installed without damaging the OR oordinators, such as fire-rated surface vertical rod exit device strikes. Latch will need to be lowered to compensate for the height of the coordinator and mounting bracket. M-V are designed for Von uprin soffit latch. Mounting brackets are made of steel. Product Jamb epth Stop Width M1 5" 1-1/2" - 2-1/4" 4" W x 3" x 1-5/8" T M1V 5" 1-1/2" - 2-1/4" 4" W x 3" x 1-5/8" T M2 5-7/8" 2-3/8" - 3-1/4" 4"W x 4" x 1-5/8"T M2V 5-7/8" 2-3/8" - 3-1/4" 4"W x 4" x 1-5/8"T M3 6-7/8" Over 3-3/8" 4"W x 3-1/2" x 1"T M3V 6-7/8" Over 3-3/8" 4"W x 3-1/2" x 1"T 13 M3V inishes Ives inish USP SP28 SPLK HM xterior Hardware 13

91 oordinators ravity oordinators 14 Meets NSI/HM 156.3, Type 21. UL Listed for ire oors. Meets NSI/HM 156.3, Type 21. OR7 and OR9 1 ravity oordinators When active door is open, coordinator prevents active door from closing until inactive door bypasses. losing of inactive door causes strike plate on top of door to contact cam and lift arm, allowing active door to close. s inactive door continues closing, roller rides over strike plate on to door bracket, holding arm above active door. Non-handed. ravity action arm and door bracket are adjustable on the job for ease of installation. Rubber roller provides quiet and efficient operation, and helps protect the astragal and doors from damage. Nylon roller on short arm glides smoothly over door bracket and strike, ensuring silent operation. Made of forged brass. OR7 for use on pairs of doors with astragal on active door up to 4' or with astragal on inactive door up to 3'4" or with astragal on both doors up to 2'10" OR9 for use on pairs of doors with astragal on active over 4' or with astragal on inactive door over 3'4" or with astragal on both doors over 2'10" Product Projection OR7 7" OR9 9" inishes Ives inish US3 US4 US10 US10 US26 US26 HM arry ar Used when it is possible for the inactive door to be opened before the active door. Prevents damage to the doors and other hardware. Nylon roller insures quiet and efficient operation. Non-handed. ll-steel construction. Standard sex bolts for mounting. xterior Hardware inishes Ives inish US3 US4 US10 US10 US26 US26 SPLK USP HM

92 Ordering uide ar oordinators How to Order OR and ccessories OR 52 US28 L20 36" OR Size: 32, 42, 52, 60, 72 inishes: US28, US26, 315N iller ar (if desired): L20, L32, L44 Vertical Rod xit evice utout Type (if applicable):,,,,,, If other Vertical Rod xit evice not listed on chart, from page 16, include information as shown on page 16. ctive oor Size Required for LL Vertical Rod xit evice pplications To determine the size OR you need: 1. Start with the active door width (X). 2. Next consider the overall frame opening between stops (). 3. Preferably, the coordinator would equal the active door width (X) + approximately 1/2 inactive door width (Y). The coordinator must be 6" longer than the active door width (X) and less than the overall frame opening between stop (). V STOP THIKNSS X TIV L OORINTOR TIV OOR WITH Y INTIV OOR WITH INTIV L STOP WITH W 15 xamples: Pair of 30" oors, 5/8" ctive oor Size, X = 30" Overall rame Opening between, = 58-3/4" Recommended oordinator: OR42 Pair of 36" oors, 5/8" ctive oor Size, X = 36" Overall rame Opening between, = 70-3/4" Recommended oordinator: OR52 36" ctive oor, 18" Inactive door, 5/8" ctive oor Size, X = 36" Overall rame Opening between, = 52-3/4" Recommended oordinator: OR42 48" ctive oor, 24" Inactive oor, 5/8" ctive oor Size, X = 48" Overall rame Opening between, = 94-3/4" Recommended oordinator: OR60 xterior Hardware 15

93 oordinators Special actory Preparation for Use with Vertical Rod xit evices oordinators may need to be prepared at the factory for use with some surface or concealed vertical rod exit devices. (See hart below) If the exit device is not listed the following information is needed. 1. xit evice Manufacturer and Model No. 2. ctive oor Size, X 3. Inactive oor Size, Y 4. xit evice ackset, U 5. Stop Width, W 6. Stop Thickness if other than 5/8", V 16 xterior Hardware xit evice xit evice evice Maximum oordinator oordinator Mounting racket Manufacturer Number ackset ctive oor Size Needed utout Type Needed 33" 42" Von uprin /8" 43" 52" 51" 60" Type None 63" 72" Von uprin /4" 33" 42" M1V, M2V 43" 52" Type or M3V 51" 60" see page 3 63" 72" 33" 42" Von uprin /8" 43" 52" 51" 60" Type None 63" 72" 33/ " 42" Von uprin 33/ /4" 43" 52" 98/ " 60" Type None 98/ " 72" 33/ " 42" Von uprin 33/ /4" 43" 52" 98/ " 60" Type None 98/ " 72" 33/3547W 34" 42" Von uprin 33/3547W- 1-5/16" 44" 52" 98/9947W 52" 60" Type None 98/9947W- 65" 72" " 42" Monarch XX- 2-3/4" 43" 52" -XX- 51" 60" Type None 24-63" 72" W -17--W 18--W -18--W 33" 42" Monarch XX--W 2-13/16" 43" 52" -XX--W 51" 60" Type None 24--W 63" 72" -24--W 25--W -25--W 16

94 Surface olts, Latches & atches Table Of ontents Surface olts page S360 Surface olt S453 Surface olt S1600 Surface olt S1601M1 Surface olt S1601M2 Surface olt Surface olt, ecorative Surface olt, ecorative S48 Mortise oor olt utch oor olt oor uards 481 hain oor uard Solid ar oor uard Roller Latch RL30 Roller Latch RL32 Roller Latch RL36 Roller Latch RL38 Roller Latch RL1152 Roller Latch STK685 Strike Plate STK685L Strike Plate ngle Stop S18 ngle Stop S895 ngle Stop Latches/atches L11 Invisible Latch L12 Invisible Latch L14 uxiliary Pusher L21 all atch L21 all atch L22 all atch Magnetic atch Magnetic atch, Heavy uty Magnetic atch, Heavy uty Roller atch Roller atch Roller atch all atch, djustable all atch, ual djustable all atch xterior Hardware 1

95 Surface olts S360 Surface olt Surface olt has 1-1/4" throw for maximum security. Jimmy-resistant design, bolt locks automatically when thrown, can be released only be pressing knob toward door while retracting. Ideal for all types of doors. vailable in 12" length Unit locks in both the up and down position. ccepts padlock (not furnished) with maximum 3/8" diameter shackle, minimum 1-3/4" shackle opening height. Units packed with one-way screws for added security. Standard screws also supplied. Units packed with both a universal top strike (US) and a mortise bottom strike (MS). onstructed of heavy duty steel. Optional Sex olts available. Optional Mortise Strike available. 2 xterior Hardware Meets NSI/HM UL listed 3 hour fire door, up to 10'0" Miami ade ounty NO Listed Meets NSI/HM L84161 UL listed 3 hour fire door, up to 10'0" ar: 3/4" Wide x 3/4" Thick Overall Width: 2-1/32" Overall Projection: 2-1/16" Top Strike: 1-1/2" Wide x 1-1/2" Long x 3/16" Thick Optional Mortise Strike: 1-5/8" Wide x 3-1/2" Long x 1/8" Thick inishes Ives Number US2 HM 603 S453 Surface olt Surface olt has 1-3/16" throw for maximum security. Strong tension springs prevent creep. Ideal for all types of doors. vailable 8" & 12" lengths. Units packed with standard screws for added security. Units packed with both a universal top strike (US) and a mortise bottom strike (MS). onstructed of heavy duty steel. Optional Sex olts available. Optional Thru olts available. ar: 3/4" Wide x 1/4" Thick Overall Width: 2-1/32" Overall Projection: 1-5/16" Top Strike: 1-1/2" Wide x 1-1/2" Long x 3/16" Thick ottom Strike: 1-5/8" Wide x 3-1/2" Long x 1/8" Thick inishes Ives Number US2 US3 US4* US10 US10 US26 HM * only available in 8 bolt length. 2

96 Surface olts 1630 meets NSI/HM , L84161 and UL listed 3 hour fire doors up to 8'0" in height meets NSI/HM , L S1600 Surface olt Standard Surface olt has 1" throw for maximum security. Ideal for all types of doors. ully concealed mounting prevents vandalism. vailable in locking version. Unit locks in both the up and down position. Locking olts are furnished with 2 keys in 4 keying variations. Units packed with wood and machine screws to meet most field conditions. Units available with either a universal top strike (T) or a flat bottom strike () Series is constructed of heavy duty steel Series is constructed of brass. Optional sex bolts available ody: 8" Long x 7/8" Wide x 3/4" Thick, Overall Knob or Lock Housing Projection: 1-1/2" Top Strike: 1-1/4" Wide x 7/8" Tall x 15/16" eep ottom Strike: 3" Long x 1" Wide x 1/8" Thick S1630 inishes steel Ives Number US2 US10 US26 HM S1600M1 S1600M2 UL listed 3 hour fire doors up to 8'0" in height. S1640 inishes brass Ives Number US3 US10 US26 HM S1600M1 S1600M2 Surface olt Standard Surface olt has 3-1/2" throw for maximum security and for doors with larger undercuts. Sleek handle design. Ideal for all types of doors. ully concealed mounting prevents vandalism. vailable in locking version. Unit locks in both the up and down position. Locking bolts are furnished with 2 keys in 4 keying variations. Units packed with wood and machine screws to meet most field conditions. Units available with either a universal top strike (T) or a flat bottom strike (). onstructed of heavy duty steel. Optional sex bolts available ar: 11" Long x 3/4" Wide x 3/4" Thick, locking version 1-1/2" Thick Top Strike: 1-1/4" Wide x 7/8" Tall x 15/16" eep ottom Strike: 3" Long x 1" Wide x 1/8" Thick inishes Ives Number SP4 SP10 SP28 SP313 SPLK HM xterior Hardware 3

97 xterior Hardware ecorative Surface olts 4 Meets NSI/HM ecorative Surface olt oncealed screw design enhances appearance and security. xceptional strength and durability provided by interlocking construction of heavy gauge track and rod. Permanent stop prevents rod disengagement from track. Tension spring holds bolt in desired position. Track assures smooth operation and interlocks with side edges of rod to eliminate marring. ecorative 5/8" diameter knob designed to facilitate bolt operation. Made from extruded brass or aluminum. vailable in 3", 4" and 6" lengths. Packed with both Universal and Mortise Strikes. Optional Surface Strike available. Throw: 15/16" Projection: 3/4" Width: 11/16" Length: 3", 4" or 6" inishes brass Ives Number HM inishes aluminum Ives Number 3* 15* P28 716* HM * only available 3 bolt Schlage arded. 4

98 ecorative Surface olts Meets NSI/HM ecorative Surface olt Throw: 1-1/8" Projection: 1-5/16" Half Round Rod: 5/8" Overall Width: 1-5/8" Length: 8" or 12" Heavy duty, decorative bolt ideal where extra strength required ecorative 1-1/4" diameter knob fits well with any décor and designed to facilitate bolt operation. Made from solid brass. vailable in 8" and 12" lengths. Packed Universal Strike (US) & Mortise Strike (MS). inishes Ives Number HM xterior Hardware 5

99 utch oor & Mortise oor olts 6 xterior Hardware Meets NSI/HM Meets NSI/HM utch oor olt Practical, rugged, attractive bolt for application on dutch doors as well as other areas. hamfered rod end draws the two leaves of door tightly together. Sufficient tolerance provided in strike opening to allow for misalignment of door leaves and also prevents binding of bolt. ecorative 1" diameter knob designed to facilitate bolt operation. Made from solid brass. Packed with Standard Strike (SS), Mortise Strike (MS) and Universal Strike (US). Throw: 5/8" Projection: 1-1/8" Half Round Rod: 5/8" Overall Width: 1-5/8" Rod Length: 4-1/4" Overall Length: Specify 4-3/8" (Including Knob) inishes Ives Number HM S48 Mortise oor olt rass oval turn knob and escutcheon. Steel bolt for extra strength. Rack is milled for precision fit with pinion. ackset: 1-3/4" olt Throw: 1/2" olt iameter: 1/2" ase: 2-1/2" Long x 9/16" diameter Strike: 1-3/4" High x 7/8" Wide inishes brass Ives Number HM

100 oor uards Meets NSI/HM Meets NSI/HM hain oor uard Permits the door to be slightly opened to allow viewing. Narrow chain holder maintains chain in stationary position when door guard is not in use, eliminating marring of door and frame caused by dangling chain. Welded twist link steel chain finished to match door plate and chain holder. Made from wrought brass or burnished wrought steel. Packed with sheet metal screws. oor Plate: 3-3/8" Long x 1-7/16" Wide hain Holder: 1-10/16" High x 3/4" Wide hain Length: 4-3/4" inishes brass Ives Number 3 26 HM inishes steel Ives Number HM Solid ar oor uard or use on doors that are flush with frames. The solid bar, interlocking with the ball on the strike plate, permits the door to be slightly opened to allow viewing. The hinged bar allows the door guard to be positioned 180 away from the door when not in use. dge guard only, furnished with cast brass door guards, minimizes the chance for marring the door or frame. Strike plate is designed to prevent the solid bar from marring the inside of the door when in use. Made from cast brass or cast aluminum. Packed with sheet metal screws. Shims available in US26 (626) only, 1/8 or 3/8. ast rass ast luminum Strike Plate: 2-5/8" High x 1-1/32" Wide Strike Plate: 2-1/2" High x 7/8" Wide Holder: 1-3/4" High x 1-1/16" Wide Holder: 2-1/2" High x 15/16" Wide rm Length: 4-3/4" rm Length: 3-13/16" dge uard: 1-1/8" High x 1-1/32" Wide inishes brass Ives Number HM inishes aluminum Ives Number HM xterior Hardware 7

101 Roller Latches Meets NSI/HM , RL30 Roller Latch ctuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed. The projection of the roller is easily adjusted using adjusting screws on the face of the unit. Maximum projection of the roller is 3/8" allowing for variance in the door clearance. Nylon Roller Standard. orged rass onstruction. Optional Strike S. Optional rass Roller, must be ordered separately. ody: 1" Wide x 3-3/8" High x 1-11/16" eep Strike: 1-11/16" Wide x 2-1/4" High x 5/32" Thick, Lip to enter- 1-5/16" Optional SStrike:1-1/4" Wide x 4-7/8" High x 3/32" Thick, Lip to enter- 1-1/4" inishes brass Ives Number US3 US4 US10 US10 US26 US26 HM xterior Hardware Meets NSI/HM , RL32 Roller Latch ctuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed. The projection of the roller is easily adjusted by turning knurled knob on back of latch. Maximum projection of the roller is 1/2" allowing for variance in the door clearance. its heavy-duty cylindrical lock cutout. Nylon Roller Standard. Non-handed. rass onstruction. Optional Strike S. ody: 1-1/8" Wide x 2-1/4" High x 2-1/4" eep Strike: 1-1/8" Wide x 2-3/4" High x 3/32" Thick, Lip to enter- 1-1/4" Optional S Strike: 1-1/4" Wide x 4-7/8" High x 3/32" Thick, Lip to enter- 1-1/4" inishes brass Ives Number US3 US4 US10 US10 US26 US26 HM

102 Roller Latches Meets NSI/HM , L57082 RL36 Roller Latch ctuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed. The projection of the roller is easily adjusted by turning slotted screw on back of latch. Maximum projection of the roller is 5/16" allowing for variance in the door clearance. its cylindrical lock cutout. Nylon Roller. Non-handed. Stainless Steel onstruction. Optional Strike S. ody: 1" Wide x 2-1/4" High x 2" eep Strike: 1-1/8" Wide x 2-3/4" High x 3/32" Thick, Lip to enter- 1-1/4" Optional S Strike: 1-1/4" Wide x 4-7/8" High x 3/32" Thick, Lip to enter- 1-1/4" inishes Stainless Steel Ives Number US32 HM 630 Meets NSI/HM , L27092 RL38 Roller Latch ctuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed. The projection of the roller is easily adjusted by turning slotted screw. Maximum projection of the roller is 3/8" allowing for variance in the door clearance. Nylon Roller. Non-handed. Stainless Steel onstruction. ody: 1-3/8" Wide x 2"High x 7/8" eep Strike: 1" Wide x 2-1/8" High x 3/8"eep inishes Stainless Steel Ives Number US32 HM xterior Hardware 9

103 Roller Latches Meets NSI/HM , RL1152 Roller Latch ombination of RL30 Roller Latch and ngle Stop. ctuation is simple, closing of the door causes the roller to fall in the depression of the strike, thereby holding the door closed. The projection of the roller is easily adjustable using adjusting screws on the face of the unit. Maximum projection of the roller is 3/8" allowing for variance in the door clearance. Nylon Roller Standard. orged rass onstruction. Optional rass Roller, must be ordered separately. ody: 1-1/2"Wide x 4-1/2" High x 1-3/4" eep with 3/4" ngle Strike: 1-1/8" Wide x 2-1/4" High x 5/32"Thick inishes Ives Number US3 US4 US10 US10 US26 US26 HM /16" Optional Strike 3/32" STK685 Strike ustom make strike for doors that swing both directions. or use with roller latches. onstructed of 3/32" brass. imple of strike centered on strike. Specify frame depth -. Overall strike length will be + 3/8 to accomodate 3/16 lip on each side inishes Ives Number US3 US4 US10 US10 US26 US26 HM /32" 2-1/4" xterior Hardware STK685L Strike ustom make strike for doors that swing both directions. or use with roller latches. onstructed of 3/32" brass. Location of strike dimple is variable. Please specify frame depth - and location of dimple from edge of frame -. imple will be located + 3/16" to accomodate lip. Specify frame depth -. Overall strike length will be + 3/8 to accomodate 3/16 lip on each side inishes Ives Number US3 US4 US10 US10 US26 US26 HM

104 xterior Hardware ngle S895 ngle Stop Surface applied stop for single doors. Large rubber bumper to ensure quiet operation. onstructed of 1/8" rass ngle. 1-1/2" Wide x 1" ngle x 2-1/2" Long inishes Ives Number US3 US4 US10 US10 US26 US26 HM S18 ngle Stop Surface applied stop for single and double doors. Includes SR64 door silencers to ensure quiet operation. SR64 silencers are replaceable. onstructed of 3/16" rass ngle. 1-1/2" Wide x 3/4" ngle x 3-1/2" Long inishes Ives Number US3 US4 US10 US10 US26 US26 HM

105 Invisible Latches 12 Meets NSI/HM 156.9, Meets NSI/HM 156.9, L11 Invisible Latch Invisible latch is ideal for installations where no visible latch is desired. Unit can be installed at the top, bottom or side of the door. an be mortised into the stop or surface mounted to the stop. Recommended for use on small panels, cabinet doors or light weight closet doors. Operation is simple, latching is accomplished by a slight push. To unlatch the door, a harder push releases the door and pushes the door out. rass and plastic construction. pplies 13 pounds to open the door. ody: 1-1/4" Wide x 1-7/8" High x 7/16" Thick Strike: 9/16" Wide x 1-5/16" High x 9/16" High inishes Ives Number US3 US4 US10 US26 HM L12 Invisible Latch Invisible latch is ideal for installations where no visible latch is desired. Unit can be installed at the top, bottom or side of the door. an be mortised into the stop or surface mounted to the stop. Recommended for use on larger panels or regular size doors. Operation is simple, latching is accomplished by a slight push. To unlatch the door, a harder push releases the door and pushes the door out. rass and plastic construction. pplies 27 pounds to open the door. ody: 1-1/4" Wide x 2-1/4" High x 9/16" Thick Strike: 5/8" Wide x 1-13/16" High x 9/16" Projection inishes Ives Number US3 US4 US10 US26 HM xterior Hardware Meets NSI/HM 156.9, L14 uxiliary Pusher id in the operation of the L11 and L12 where hinges or surrounding conditions prevent smooth operation of doors. Provides 1-1/16" throw. Nylon pusher. rass construction. pplies 10 pounds to open the door. ody: 2-15/16" Long x 1-11/16" Wide x 5/8" eep inishes Ives Number US3 US4 US10 US26 HM

106 all atches L21 all atch our-way catch with hexagon stud. Ideal for holding medium duty doors. The strike slides between two stainless steel balls that are under spring tension. s the strike engages, the door is held tightly shut. Strike can enter body from any direction. Spring tension is easily adjusted to suit field conditions. ody can be surface applied or mortised. rass construction. Meets NSI/HM Meets NSI/HM 156.9, Meets NSI/HM 156.9, ody: 3/4" Wide x 3" High x 3/4" eep Strike: 3/4" Wide Hex x 1-1/2" High inishes brass Ives Number US26 HM 626 L21 all atch our-way catch with plate type strike. Ideal for closet doors, access doors, hinged openings and numerous other applications. The strike slides between two stainless steel balls that are under spring tension. s the strike engages, the door is held tightly shut. Strike can enter body from any direction. Spring tension is easily adjusted to suit field conditions. ody can be surface applied or mortised. rass construction. ody: 3/4" Wide x 3" High x 3/4" eep Strike: 7/16" Wide x 1-3/4" High x 7/8" eep inishes brass Ives Number US3 US4 US10 US26 US26 HM L22 all atch Three-way catch with plate type strike. Ideal for smaller cabinet doors or panels. The strike slides between two stainless steel balls that are under spring tension. s the strike engages, the door is held tightly shut. Strike can enter body from either side or front. Spring tension is easily adjusted to suit field conditions. ody can be surface applied or mortised. rass construction. ody: 1/2" Wide x 2-3/16" High x 1/2" eep Strike: 3/8" Wide x 1-3/8" High x 5/8" eep inishes brass Ives Number US3 US4 US10 US26 US26 HM xterior Hardware 13

107 Magnetic atches 14 Meets NSI/HM Meets NSI/HM Magnetic atch ouble pole. Self aligning magnet insures maximum pull. ase design allows easy magnet adjustment on cabinet or small door applications. luminum case. Packed with sheet metal screws. 5 lbs. Load apacity ase: 1-1/8" wide x 2-1/16" Long x 5/8" Thick inishes aluminum Ives Number 3 92 HM Mighty-Mite Heavy uty Magnetic atch ual double pole. Self-aligning magnets insure maximum pull. an be surface mounted or mortised. luminum case. Packed with sheet metal screws, 2 short strikes and 1 long strike. 9 lbs. Load apacity ase: 1" Wide x 3-1/8" Long x 9/16" Thick inishes aluminum Ives Number 3 92 HM xterior Hardware Meets NSI/HM Super-Mite Heavy uty Magnetic atch ual triple pole. Self-aligning magnets insure maximum pull. an be surface mounted or mortised. luminum case. Packed with sheet metal screws, 2 short strikes and 1 long strike. 14 lbs. Load apacity ase: 1" Wide x 3-1/8" Long x 3/4" Thick inishes aluminum Ives Number 3 92 HM

108 Roller atches Meets NSI/HM Roller atch Independent rollers allow positive action and self-alignment. ushioned rollers absorb shock and noise, hold door away from cabinet. pplication allows for easy adjustment. Made from wrought steel. Packed with screws and brads. ase: 1-1/4" High x 11/16" Wide Strike: 1-1/4" High x 3/8" Wide inishes Ives Number 2 HM 603 Meets NSI/HM L27081 for brass and L87081 for steel. Meets NSI/HM L27081 for brass and L87801 for steel. 335 Roller atch Smooth, positive latching action insured by powerful conical spring. urable nylon roller insures quiet operation. djustable tension. djustments can be varied from 4 to 17 lbs. of holding power making possible a wide range of door performance. asily installed on thin doors. ull lip style strike designed for simplified mortising. Made from wrought brass or wrought steel. Packed with sheet metal screws. ace Plate: 7/8" Wide x 2-1/4" High ore: 1-3/4" eep x 13/16" iameter Strike: 1-5/8" Wide x 2-1/4" High, Lip to center- 1-3/16" inishes Ives Number HM Roller atch Smooth, positive latching action insured by powerful conical spring. urable nylon roller insures quiet operation. djustable tension. djustments can be varied from 4 to 17 lbs. of holding power making possible a wide range of door performance. asily installed on thin doors. Standard box type strike designed for neat appearance. Made from wrought brass or wrought steel. Packed with sheet metal screws. ace Plate: 7/8" Wide x 2-1/4" High ore: 13/16" iameter x 1-3/4" eep Strike: 7/8" Wide x 2-1/4" High, Lip to center- 1-1/8" inishes Ives Number HM xterior Hardware 15

109 all atches 16 Meets NSI/HM Meets NSI/HM djustable all atch Ideal for cabinets and small interior doors. ree rolling ball insures smooth, positive and trouble-free action. djustable threaded barrel compensates for various door clearances. djustable spring tension. Made from wrought brass. ace Plate: 3/4" Wide x 1-1/2" High ore: 1" eep x 9/16" iameter Strike: 25/32" Wide x 1-1/2" High, Lip to center- 13/32" inishes brass Ives Number HM ual djustable all atch or catch in door installations. ual adjustment for door clearance and holding strength. Lip strike is designed for use where strike is mounted in jamb. ree rolling ball insures smooth, positive and trouble-free action. djustable threaded barrel compensates for various door clearances. djustable spring tension. Made from wrought brass. ace Plate: 1" Wide x 2-1/8" High ore: 7/8" iameter x 1-3/8" eep Strike: 1-3/8" Wide x 2-1/8" High, Lip to center- 7/8" inishes brass Ives Number HM xterior Hardware Meets NSI/HM all atch or catch in door installations. Radiused corners allow easy installation with a router. ual adjustment for door clearance and holding strength. Lip strike is designed for use where strike is mounted in jamb. ree rolling ball insures smooth, positive and trouble-free action. djustable threaded barrel compensates for various door clearances. djustable spring tension. Made from wrought brass. ace Plate: 1" Wide x 2-1/8" High ore: 7/8" iameter x 1-3/8" eep Strike: 1-3/8" Wide x 2-1/8" High, Lip to center- 7/8" inishes brass Ives Number HM

110 oor Table Of ontents loor page S13 loor Stop R14 Riser S17 loor Stop S18, S18L loor Stop S436 loor Stop S438 loor Stop R435 Riser R437 Riser loor Stop S441, S441WS loor Stop S444, S448 loor Stop loor Stop & Holder S9 loor Stop & Semi-automatic Holder S40, S41, S42, S43 loor Stop & utomatic Holder S446, S450 loor Stop & Manual Holder S495, S496, S497 loor Stop & utomatic Holder Wall umpers/ WS11, WS11X Wall Stop WS20, WS20X Manual Wall Holder WS33, WS33X Wall Stop WS65 Wall Stop WS401, WS402 Wall umper WS404 Wall umper WS406, WS407 Wall umper R Wall umper WS443, WS447 Wall Stop WS445, WS449 Manual Wall Holder Wall Holders WS40 utomatic Wall Holder WS45, WS45X utomatic Wall Holder Kick own Holder S452 Kick own Holder S455 Kick own Holder S544, S555 Kick own Holder Plunger oor Holders S S Roller umpers R470, R471, R472 Roller umper Residential oor stops 060, 061 lexible oor Stop , 61 oor ase Stop lexible oor Stop oor ase Stop Hinge Pin Z Residential oor Saver Z ommercial oor Saver Silencers SR64, SR65, SR66 oor Silencer xterior Hardware

111 loor ome S13 ome Stop Standard S13 for use where no threshold is used. Heavy-uty ast ome constructed of brass. Unique riser design of R14 (below) allows easy conversion to threshold application. Units are packed with fasteners sufficient for mounting in all types of floor construction, including concrete. Replaceable grey rubber bumper. Meets NSI/HM 156.6, L Overall Height: 1" ase Height: 5/32" ase iameter: 1-3/4" inishes Ives Number US3 US4 US10 US10 US26 US26 HM R14 ome Stop Rise dapts the S13 ome Stop to threshold use. rass ie ast onstruction. Riser Height: 5/16" ase iameter: 1-3/4" round inishes Ives Number US3 US4 US10 US10 US26 US26 HM xterior Hardware Meets NSI/HM 156.6, L S17 ome Stop One piece dome stop for use with thresholds. Heavy-uty ast ome constructed of brass. Units are packed with fasteners sufficient for mounting in all types of floor construction, including concrete. Replaceable grey rubber bumper. Overall Height: 1-11/32" ase Height: 1/2" ase iameter: 1-3/4" round inishes Ives Number US3 US4 US10 US10 US26 US26 HM

112 loor ome S436 Meets NSI/HM , L12141 for brass or bronze and L32141 for aluminum. S438 Meets NSI/HM , L12141 for brass or bronze and L32141 for aluminum. S436 S438 ome Stop ome Stop S436 for doors without threshold. S438 for doors with threshold or undercut doors. Heavy-uty ast ome constructed of brass, bronze or aluminum. Packed with wood screw and plastic anchor. Replaceable gray, non-marring rubber bumper. S436 Overall Height: 1" ase Height: 3/16" ase iameter: 1-3/4" x 2" Oval inishes brass Ives Number US3 US4 US5 US10 US10 US15 US620* US26 US HM * only available for S436 in slim pack of 15 per box. inishes aluminum Ives Number US28 HM 628 S438 Overall Height: 1-3/8" ase Height: 9/16" ase iameter: 1-3/4" x 2" Oval 1" R435 R437 Riser for S436 ome Stop Riser for S438 ome Stop xtruded aluminum, mill finish. R435 for conversion of S436 ome Stop to carpet installation. R437 or conversion of S438 ome Stop to carpet installation. Packed with wood screws, lead shield and stud. Specify Tampin (TPN) if required. vailable in 1/4", 3/8", 1/2", 5/8", 3/4" and 1" height. 3 xterior Hardware P LOOR 1-7/16" 1" OR LSS 3

113 loor S18S S18L S18S S18L loor Security oor designed for use in high vandalism areas. Molded from black flame resistant, resilient material around a heavy-duty stud. Once grouted in concrete, leaves no exposed fasteners to be tampered with or removed. Ideal for jail or security cell areas where floor mounted stops are required. S18L also ideal for concrete wall applications. S18S Height: 1-1/2" S18L Height: 3-1/2" S18S iameter: 2" S18L iameter: 2" S18S Stud Length: 2-1/2" S18L Stud Length: 2-1/2" S434 loor Stop urnished wrought steel. or undercut doors up to 1-1/2". Packed with screws and plastic anchors. Replaceable soft, resilient gray rubber. Overall Height: 2-5/8" ase Size: 1-1/2" W x 2-3/4" L inishes Ives Number US HM loor oor Stop urnished wrought steel. or undercut doors up to 1-1/2". Packed with screws and plastic anchors. Replaceable soft, resilient gray rubber. xterior Hardware Overall Height: 1-5/16" ase iameter: 1-1/4" inishes brass Ives Number HM inishes aluminum Ives Number 3* HM * only available in Slim-Pak of 25

114 loor Meets NSI/HM , L12131 for brass S441 loor Stop ccommodates door undercut up to 1-1/2". esigned to blend well with all types of construction and provide a minimum of hindrance to cleaning efforts. Heavy-uty cast brass or aluminum construction. Replaceable Non-marring rubber bumper. S441 packed with expansion shield and tampin for masonry type mounting, and wood screws for drywall mounting. Overall Height: 2-1/8" Overall Length: 2-7/8" ase epth: 1-5/8" inishes brass Ives Number US3 US4 US5 US10 US10 US15 US26 US26 HM S444 Meets NSI/HM , L12131 for brass S448 Meets NSI/HM , L12121 for brass and L32121 for aluminum S444 S448 loor Stop loor Stop Ideal for interior or exterior use. ast brass construction. ccommodates door undercut up to 2-1/2". Replaceable Non-marring rubber tip. S444 is packed with expansion shield and lead shield, for masonry type mounting. S448 is packed with wood screws, for drywall mounting. Overall Height: 3" ase iameter: 2-1/2" 5 inishes brass Ives Number US3 US4 US5* US10 US10 US15 US26 US26 HM inishes aluminum Ives Number US28* HM 628 * not available on S444 xterior Hardware 5

115 loor Meets NSI/HM , L S9 loor Stop & Semi-utomatic Holder Semi-automatic floor-mounted holders accommodates with door to floor clearance of 1-1/2" or less. ast from heavy-duty brass. ctivate holder by flipping the engagement tongue forward. When door is opened, the hook (mounted on door) engages the tongue. To release, push firmly on door to disengage tongue. Universal screw pack accommodates all types of floor and door construction. Overall Height: 3-1/2 ase : 2" wide x 3-1/2" long 6 xterior Hardware Meets NSI/HM , L /8 LRN 1-3/16 1/2 inishes Ives Number US3 US4 US10 US10 US26 US26 HM S40 S41 S42 S43 loor Stop & utomatic Holder utomatic door holders ideal for heavy-traffic situations that require a simple, fool-proof, Hold-Open device. orged from brass. Unit is activated automatically when door is opened. firm pull on door releases the mechanism. Strikes accommodate different door to floor clearances. Model numbers are determined by strike/door-to-floor clearances. Holder position on door is adjustable. Universal screw pack allows for installation in all types of door construction. oor to loor learance: S40 1/2" or less S41 9/16" to 1-1/16" S42 1-1/8" to 1-9/16" S43 1-5/8" to 2-1/16" Holder : 3" Wide x 3-11/16" High inishes brass Ives Number US3 US4 US10 US10 US26 US26 HM SI VIW OY 40 MX. OOR LRN 1-3/4 LRN ROM 9/16 to 1-1/16 2-1/4 LRN ROM 1-1/8 to 1-9/16 2-3/4 LRN ROM 1-5/8 to 2-1/16 6 S41 S42 S43

116 loor S446 Meets NSI/HM , L11371 for brass and L31371 for aluminum. S450 Meets NSI/HM , L11361 for brass and L31371 for aluminum. S446 S450 loor Stop & Manual oor Holder loor Stop & Manual oor Holder Manual type floor holder ideal for interior or exterior use. ast brass or aluminum construction. ccommodates door undercut up to 2-1/2". Replaceable non-marring rubber tip. Unit functions as a stop but serves as a Hold-Open device when hook is manually engaged in strike. Unit requires manual disengagement to release Hold-Open. S446 packed with expansion shield and lead shield, for masonry type mounting S450 packed with 3 wood screws, for drywall mounting. Overall Height: 3-3/4 Height from loor to Stop enter Line: 2-5/8" Stop iameter: 1-1/16" ase iameter: 2-1/12" inishes brass Ives Number US3 US4 US10 US10 US15 US26 US26 HM inishes aluminum Ives Number US28 HM xterior Hardware 7

117 loor 8 xterior Hardware S495 shown S495 Meets NSI/HM , L11291 for brass S496 Meets NSI/HM , L11301 for brass S497 Meets NSI/HM , L11301 for brass S495 S496 S497 Wall Stop & utomatic Holder loor Stop & utomatic Holder loor Stop & utomatic Holder utomatic door holders ideal for heavy-traffic situations that require a simple, Hold-Open device. ast brass construction. Recommended installation is holder on door and strike on wall. Holder position on door is adjustable. Holder is tapered to prevent child riding. S495 Holds door 3-3/4" from wall. S496 oor to loor learances 3/8" Maximum. S497 oor to loor learances 1" Maximum. inishes brass Ives Number US3 US4* US10 US10 US26 US26 HM * not available on S496, S497. 8

118 Wall WS11 Meets NSI/HM , L12011 WS11X Meets NSI/HM , L12021 WS20 Meets NSI/HM , L11341for brass and L32341 for aluminum WS20X Meets NSI/HM , L11351 for brass and L31351 for aluminum WS11 WS11X Wall onstructed in heavy duty cast brass. Hexagon section on unit aids in fastening unit when expansion shield is used. Replaceable rubber bumpers features off-set shoulder and threaded shank that screws into body of unit. WS11 is furnished with wood screws for drywall mounting. WS11X is furnished with a threaded stud and expansion shield for masonry type mounting. ase iameter: 2" Overall Projection: 3-3/4" inishes brass Ives Number US3 US4 US10 US10 US26 US26 HM WS20 WS20X Manual Wall Holders onstructed in cast brass or aluminum. Replaceable rubber bumpers feature off-set shoulder and threaded shank that screws into body of holder. Hinged strike furnished matches body material and finish. WS20 is furnished wood screws for drywall mounting. WS20X is furnished with threaded stud and exspansion shield for masonry type mounting. ase iameter: 2-3/8" Overall Projection: 4" Strike Height: 2" Strike Width: 1" inishes brass Ives Number US3 US4 US10 US10 US26 US26 HM inishes aluminum Ives Number US28 HM xterior Hardware 9

119 Wall WS33 Meets NSI/HM , L12011 WS33X Meets NSI/HM , L12021 WS33 WS33X Wall onstructed in a durable cast brass. Replaceable rubber bumper with offset shoulder screws into cavity on body to prevent loss or theft. Sloping design discourages vandalism WS33 is furnished with wood screws for drywall mounting. WS33X is furnished with a threaded stud and expansion shield for masonry type mounting. ase iameter: 2-1/4" wide x 3" High Overall Projection: 3-3/4" inishes brass US Number US26 HM 626 WS65 Wall Stop urnished cast aluminum. Replaceable non-marring white rubber bumper. Packed with sheet metal screws. 10 xterior Hardware ase iameter: 1-5/8" Overall Projection: 3-3/4" inishes aluminum Ives Number US3 US10 US10 US27 HM

120 Wall umpers WS401V & WS402V Meets NSI/HM L12251 for brass WS401VX & WS402VX Meets NSI/HM L12101 for brass WS401VX WS401V WS402VX WS402V ase iameter: 2-1/2" ase Thickness: 3/8" Overall Projection: 1" Wall umpers onstructed in heavy-duty cast brass. Special retainer cup makes rubber tamper resistant. WS401VX (401) convex rubber bumper, packed with wood screw and plastic anchor. WS401V (401-1/2) concave rubber bumper which avoids damage to locks with projecting buttons, packed with wood screw and plastic anchor. WS402VX (402) convex rubber bumper packed with screw and drywall anchor. WS402V (402-1/2) concave rubber bumper which avoids damage to locks with projecting buttons and is packed with screw and drywall anchor. inishes Ives Number US3 US4 US10 US10 US15 US26 US26 HM WS404VX Wall umpers ompact size. onstructed in cast brass. Totally concealed mounting discourages vandalism or tampering. Unit furnished with grey convex rubber bumper. Packed with sheet metal screw, rawl plug and brad. ase iameter: 1" Overall Projection: 17/32" inishes Ives Number US3 US4 US5 US10 US10 US15 US26 US26 HM xterior Hardware 11

121 xterior Hardware Wall umpers WS406VX & WS407VX Meets NSI/HM L22201 for brass, and L52101 for stainless steel. WS406V & WS407V Meets NSI/HM L22251 for brass and and L52251 for stainless steel. WS406VX WS406V WS407VX WS407V ase iameter: 2-1/2" ase Thickness: 3/8" Overall Projection: 1" Wall umpers onstructed in sturdy yet economical wrought base of brass or stainless steel construction. eature concealed tamper-proof mounting. Shipped factory preassembled backplate to reduce installation cost. asy installation by inserting screwdriver through small hole in rubber. WS406VX (406) convex rubber bumper, packed with wood screw and plastic anchor. WS406V (406-1/2) concave rubber bumper, which avoids damage to locks with projecting buttons, packed with wood screw and plastic anchor. WS407VX (407) convex rubber bumper packed with screw and drywall anchor. WS407V (407-1/2) concave rubber bumper which avoids damage to locks with projecting buttons and is packed with screw and drywall anchor. inishes brass Ives Number US3 US4 US5* US10 US10 US15 US15** US26 US26 716** HM * inishes stainless steel Ives Number US32 HM 630 * only available on WS407VX Slim-Pak of 15 ** available on WS407V or WS407VX Slim-Pak of 15 12

122 Wall umpers 411R-W Wall umper dhesive-backed wall door stop for use on clean, smooth, flat surfaces only. Non-marring white rubber. oncave design permits knob to strike stop without damaging or engaging lock mechanism. ase iameter: 1-7/8" ase Thickness: 3/8" Overall Projection: 1-1/16" 13 xterior Hardware 13

123 Wall & Holders WS443 Meets NSI/HM , L12021 for brass and L32021 for aluminum. WS443 WS447 Wall Stop onstructed in brass. Ideal for interior or exterior use. Replaceable non-marring rubber tip. WS443 is packed with expansion shield and lead shield for masonry type mounting. WS447 is packed with wood screws for drywall mounting. ase iameter: 2-1/4" Overall Projection: 3-11/16" inishes brass Ives Number US3 US4 US10 US10 US15 US26 US26 HM xterior Hardware WS445 Meets NSI/HM , L11351 for brass. WS449 Meets NSI/HM , L11341 for brass and L31341 for aluminum. WS445 WS449 Manual Wall Holder onstructed in cast of brass or aluminum. Unit functions as a stop but serves as a Hold-Open device when hook is manually engaged in strike. Unit requires manual disengagement to release Hold-Open. Replaceable resilient, non-marring rubber tip. WS445 is packed with expansion shield and lead shield for masonry type mounting. WS449 is packed with wood screws for drywall mounting. ase iameter: 2-1/4" ase Projection: 3-11/16" ngaged Projection: 5-3/4" Strike Height: 1-1/2" Strike Width: 13/16" Strike Projection: 13/16" inishes brass Ives Number US3 US4 US10 US10 US15 US26 US26 HM inishes aluminum Ives Number US28* HM 628 * only available on WS449 14

124 utomatic Wall Holders WS40 utomatic Wall Holder onstructed of sturdy cast brass, or aluminum. Holder is mounted on wall and strike is mounted on door. Roller on holder rides up seats itself on strike, with a heavy duty bumper pad deadening the sound and shock. Universal screw pack accommodates all types wall construction. Meets NSI/HM , L11291 for brass and L31291 for aluminum. ase Height: 2" ase Width: 2-1/2" ase Projection: 2-1/4" ngaged Projection: 3-1/2" inishes brass Ives Number US3 US4 US10 US10 US26 US26 HM inishes aluminum Ives Number US28 HM 628 Strike Height: 2-1/16" Strike Width: 3/4" Strike Projection: 2" WS45 Meets NSI/HM , L11291 for brass and L31291 for aluminum. WS45 WS45X utomatic Wall Holder onstructed of cast brass, bronze or aluminum. Spring loaded roller rides up the face of the strike, seating itself on the strike, holding the door firmly in the open position. heavy rubber pad cushions the shock and absorbs the sound. With unit mounted on door and the strike on wall, vertical adjustment is available on body. The strike is adjustable 45 degrees left or right, both adjustments easily accomplished at time of installation or at a later date. WS45 strike is furnished with wood screws for drywall mounting. WS45X strike is furnished with a threaded stud and expansion shield for masonry type mounting. ase Height: 3-11/16" Strike iameter: 2-3/8 ase Width: 3" Strike Projection: 3" ase Projection: 2" ngaged Projection: 3-7/16" inishes brass Ives Number US3 US4 US10 US10 US26 US26 HM inishes aluminum Ives Number US28 HM xterior Hardware 15

125 Kick own Holders Meets NSI/HM , L11383 for brass and L31383 for aluminum. S452 Kick own Holder Units provide simple hold and release, activated with a touch of the foot. ast brass or aluminum construction. Stainless steel spring. Replaceable non-marring rubber shoes have corrugated bottoms to provide secure grip. Shoes are easily replaced when worn. Shoe held on with screw. Packed with sheet metal screws. S452-4 has a door-to-floor clearance of 2" or less. S452-5 has a door-to-floor clearance up to 3". S452-4 oor-to-loor learance: 2" or less S452-5 oor-to-loor learance: Up to 3" S452-4 Plate Height: 2-1/8" S452-5 Plate Height: 2-1/8" S452-4 Plate Width: 1" S452-5 Plate Width: 1" inishes brass Ives Number US3 US4 US10 US10 US15 US26 US26 HM inishes aluminum Ives Number US28* HM 628 * available in 4" only 16 S455 Kick own Holder Units provide simple hold and release, activated with a touch of the foot. ast brass or aluminum construction. Replaceable non-marring rubber shoes have corrugated bottoms to provide secure grip. When worn, shoes are easily replaced. Shoe held on with screws. oor-to-floor clearances of 2" or less. xterior Hardware Meets NSI/HM , L11382 for brass and L31382 for aluminum. oor-to-loor learance: 2" or less Plate Height: 1-3/4" Plate Width: 1-3/4" inishes brass Ives Number US3 US4 US5 US10 US10 US15 US26 US26 HM inishes aluminum Ives Number US3L US5L US10L US27 HM

126 Kick own Holders S544 Meets NSI/HM , L11381 S555 Meets NSI/HM , L11391 S544 S555 Kick own Holder Units provide an economical method to hold open doors. ast of durable iron. Non-marring rubber shoes have corrugated bottoms to provide secure grip. Rubber shoe is securely fastened with screw. When worn, shoes are easily replaced. S544 for door-to-floor clearances of 2" or less S555 for door-to-floor clearances up to 3". S544 oor-to-loor learance: 2" or less Plate Height: 2-1/4" Plate Width: 1-7/16" S555 oor-to-loor learance: Up to 3" Plate Height: 2-1/4" Plate Width: 1-7/16" inishes Ives Number SP4 SP10 SP28 SP313 SPLK HM xterior Hardware 17

127 Plunger Type oor Holders S1153 Plunger Type oor Holder Provides a contemporary yet economical method of positive Hold-Open. onstructed in sturdy cast aluminum. Spring operated plunger activates with minimal pressure, releasing instantly with a light tap on the plat-form lever. Provides a 1-5/8" throw for all types of doors. Ribbed non-marring rubber shoe is securely fastened to unit with a screw and is easily replaced when worn. Meets NSI/HM , L Height: 6-1/4" Width: 1-1/2" epth: 1-7/16" inishes Ives Number US28 HM 628 S1154 Plunger Type oor Holder onstructed from heavy-duty cast brass or bronze. Plunger and internal parts are plated steel and provides a 1-1/4" throw for all types of doors. Plunger is easily activated with minimal pressure, releasing instantly with a light tap on the platform lever. Round non-marring rubber shoe is securely fastened with a screw in flanged cup to prevent movement or loss. When worn, shoes are easily replaced. 18 Meets NSI/HM , L Height: 5-1/2" Width: 2" epth: 1-1/4" inishes Ives Number US3 US4 US10 US10 US26 US26 HM xterior Hardware 18

128 Roller umpers S470 Meets NSI/HM , L12212 Offset R470 R471 R472 Roller umpers onstructed in heavy-duty cast brass. R470 used where two doors open against each other to prevent damage to the doors or hardware. R471 and R472 are ideal for use in situations where doors meet each other at approximate right angles (back to back). Replaceable rubber roller available. R470 ase Size: 1-11/16" x 2-1/4" R470 rm Offset: 2-3/4" R470 Length: 5" S471 R471 ase iameter: 2" R471 Length: 4-1/2" R472 ase iameter: 2" R472 Length: 6" Meets NSI/HM , L12192 inishes Ives Number US3 US4** US10* US10* US15* US26 US26 HM ** 612* 613* 619* * only available on R472 ** only available on R471 and R S472 Meets NSI/HM , L12202 xterior Hardware 19

129 Residential oor Meets NSI/HM lexible oor 061 Utilizes heavy gauge spring to maintain rigid protections Simple to install - only a screwdriver required Made from burnished wrought steel Packed disassembled for quick installation Replaceable white rubber tip available ase iameter: 1" Tip iameter: 19/16" 060 3" Projection 061 4" Projection inishes steel Ives inish * 26 -W** HM * only available on 060 ** only available on ase oor 61 vailable in three sizes to accommodate varying areas of installation and door trim dimensions Made from solid brass or aluminum 61 also available in epoxy colored aluminum Replaceable white rubber tip available /4" Projection, ase iameter: 1" /8" Projection on brass units, 3-3/16" Projection on aluminum units, ase iameter: 7/8" Tip iameter: 5/8" inishes brass Ives inish * ** HM xterior Hardware inishes aluminum Ives inish 3 5* 10* * 19* * -LK -W* HM inishes zinc Ives inish Z605* Z619* Z716* HM * only available on 61 ** only available on 61 Schlage arded or slim package of 15 20

130 Residential oor 63 lexible oor Utilizes heavy gauge spring to maintain rigid protections Simple to install - only a screwdriver required Made from burnished wrought steel Packed disassembled for quick installation Replaceable white rubber tip available ase iameter: 1" Tip iameter: 9/16" Projection: 3" inishes steel Ives inish W HM ase oor Stop ase oor Stop features deluxe one-piece styling asily screws into base esigned with square head to accommodate wrench or pliers when installing Made from solid brass or aluminum Replaceable white rubber tip available ase iameter: 1" Tip iameter: 9/16" Projection: 3-1/4" inishes brass Ives inish HM inishes aluminum Ives inish HM Hinge Pin oor or use on hinged doors where the installation of a standard door stop is not desirable Positive slip proof adjustment Non-marring rubber tips Removable bushings accommodate 1/4" to 5/16" diameter hinge pins asy installation only a screwdriver required Made from burnished wrought steel Replaceable white rubber tip available oor Opening 70 to 100 oor Opening djustments inishes steel Ives inish HM xterior Hardware

131 Residential oor 22 oor Saver 70 Hinge Pin oor or use on hinged doors where the installation of a standard door stop is not desirable esigned for narrow trim installation High quality rubber bumpers - shoulder on stud supports rubber through entire body for engineered cushioning Removable bushings accommodate 1/4" to 5/16" diameter hinge pins asy installation Made from solid brass, aluminum, or epoxy coated aluminum Replaceable white rubber tip available 70-Zinc oor Opening 85 to 125 oor Opening djustments inishes brass Ives inish * * HM inishes aluminum Ives inish W -LK HM inishes zinc Ives inish Z605 Z406** Z619** Z716 * only available in Schlage arded or Slim-Pak of 25 HM ** only available in Schlage arded 72 Hinge Pin oor or use on hinged doors where the installation of a standard door stop is not desirable esigned for narrow trim installation High quality rubber bumpers - shoulder on stud supports rubber through entire body for engineered cushioning Removable bushings accommodate 1/4" to 5/16" diameter hinge pins asy installation Made from solid brass, aluminum, or epoxy coated aluminum oor Opening 85 to 125 oor Opening djustments inishes zinc Ives inish Z605 Z609 Z613 Z619 Z625 Z-W HM xterior Hardware oor Saver Meets NSI/HM 156.6, L12141 for brass or bronze and L32141 for aluminum. 73 Hinge Pin oor or use on hinged doors where the installation of a standard door stop is not desirable esigned for narrow trim installation High quality rubber bumpers - shoulder on stud supports rubber through entire body for engineered cushioning Removable bushings accommodate 1/4" to 5/16" diameter hinge pins asy installation Made from solid brass, aluminum, or epoxy coated aluminum oor Opening 85 to 125 oor Opening djustments inishes zinc Ives inish Z605 Z613 Z619 Z625 HM 22

132 oor Silencers Meets NSI/HM , L Meets NSI/HM , L03021 SR64 iameter: 1/2" Thickness: 1/8" inishes RY, TN SR65 Height: 3/4" iameter: 3/8" Thickness: 1/8" inishes RY SR66 iameter: 1/2" Thickness: 1/8" inishes RN, RY, WHT oor Silencer or use on metal frames featuring pneumatic design that, once installed, forms an air pocket to absorb shock and reduce noise of door closing. Tamper-proof once installed on the frame. Proper installation also eliminates door rattle and provides constant tension for door latches or locks. Packed in bags of 100. rey vailable in bulk pack of ach bag has an installation tool included. oor Silencer or use on wood frames, also feature pneumatic design to cushion shock and absorb noise. To prevent removal, a small brad should be driven into stop strip and through stem of silencer, as shown in the detail. Packed in bags of 100. oor Silencer Self dhesive Rubber Silencers. conomical installation requires no drilling of frames. Packed two sheets of 50 (100 minimum). 23 xterior Hardware 23

133 Notes 24 xterior Hardware 24

134 xterior Hardware Table Of ontents Lock uards page L1, L7 Lock uard L10 Lock uard L11 Lock uard L12 Lock uard L13 Lock uard L14 Lock uard Viewers U696 One-way Viewer , U698 One-way Viewer , U700 One-way Viewer , U701 One-way Viewer oor Knockers 3107 oor Knocker oor Knocker Letter ox 620 Letter ox Plate Letter ox Sleeve oor Numbers oor Numbers Storm and Screen oor 980 Storm oor Latch Screen oor Pull rash Stop S115 rash Stop xterior Hardware 1

135 Lock uards L1 L7 Lock uard Units are non-handed and incorporate security frame pin to prevent separation of the door and frame. L7 does not incorporate the security frame pin Unit covers the latch bolt area of the door and lock, thereby providing added protection from burglars, vandals or normal abuse. Ideal for use with mortise or cylindrical locks. asy installation. Through bolted with carriage bolts and nuts. vailable in a variety of materials, 13 gauge stainless steel, 12 gauge steel and brass material. 3" Wide x 11-1/2" High olt center to center: 10-1/2" inishes Ives Number USP* US2* US4* US10* US32 SP313* HM * not available on LP7 2 xterior Hardware L10 Lock uard Ideally suited for use with rose or escutcheon 2-3/4" wide or less. or use with Type 86 Mortise and Type 161 ylindrical Locks (NSI Series 1000 and NSI Series 4000). No exposed fasteners on face of unit. Unique design provides maximum security, virtually eliminating the opening between door and frame at the latch point. vailable in 13 auge Stainless Steel or 12 auge Steel. 2-1/2" Wide x 9-1/2" High Stud center to center: 8-1/2" inishes Ives Number USP US32 HM

136 Lock uards L11 Lock uard esigned for use on aluminum doors with latch-type locks or doors equipped with electric strikes. Unit is Handed - Specify left or right hand when ordering. No exposed fasteners on face of unit. Unique design provides maximum security, virtually eliminating the opening between door and frame at latch point. vailable in 13 auge Stainless Steel or 12 auge Steel. 2-1/2" Wide x 9-1/2" High Stud center to center: 8-1/2" inishes Ives Number US32 SP313 HM L12 Lock uard Narrow design unit for use on rose or escutcheon 3-1/2" or less. or use with Type 86 Mortise and Type 161 ylinder Locks (NSI Series 1000 and NSI Series 4000). No exposed fasteners on face of unit. Unique design provides maximum security, virtually eliminating the opening between door and frame at the latch point. vailable in 13 auge Stainless Steel or 12 auge Steel 1-1/2" Wide x 9-1/2" High Stud center to center: 8-1/2 inishes Ives Number USP US32 HM xterior Hardware 3

137 Lock uards L13 Lock uard esigned for use on all Type 161 ylindrical Locks (NSI Series 2000) Monolock and Unilock. No exposed fasteners on face of unit. Unique design provides maximum security, virtually eliminating the opening between door and frame at latch point. vailable in 13 auge Stainless Steel or 12 auge Steel. 1-1/2" Wide x 7" High Stud center to center: 4-1/2" inishes Ives Number USP US32 HM L14 Lock uard Narrow design unit for use on rose or escutcheon 3-1/2" or less. or use with Von uprin 6210 and 6211 electric strike. No exposed fasteners on face of unit. Unique design provides maximum security. vailable in 13 auge Stainless Steel 2-9/16" Wide x 9-1/2" High Stud center to center: 8-1/2" inishes Ives Number US32 HM xterior Hardware 4

138 Viewers Meets NSI/HM L23222 UL Listed 90 minute fire doors U696 One-Way Viewer 150 ngle of View. or doors 1-3/8" to 2-1/16" thick. Secure, tamper-resistant. Solid brass body; glass lens. Simple installation only a 1/2" hole required. Suggested installation height: 60" from floor. Trim washer available, 3/4" x.032" thick. inishes Ives Number HM U698 One-Way Wide ngle Viewer 190 ngle of View. Lens projects 1/4" from face of door. 4 optical glass lenses. or doors 1-3/8" to 2-1/8" thick. Solid brass body and barrel. Simple installation only a 9/16" hole required. Suggested installation height: 60" from floor. 698 meets NSI/HM L23172 U698 meets NSI/HM L23222 U698 is UL Listed 90 minute fire doors inishes Ives Number 3 15** * HM * not available on U698 ** only available in Schlage arded 5 xterior Hardware 5

139 Viewers 700 meets NSI/HM L23173 U700 meets NSI/HM L23222 U700 is UL Listed 90 minute fire doors 700 U700 One-Way Viewer 120 ngle of View. or doors 1-3/8" to 2-1/16" thick. Secure, tamper-resistant. Solid brass body; glass lens. Simple installation only a 1/2" hole required. Suggested installation height: 60" from floor. Trim washer available, 3/4" x.032" thick. inishes Ives Number 3** 4 10* 26 HM * not available on U700 ** only available on 700 in Schlage arded 701 U701 One-Way Viewer 120 ngle of View. or doors 2-1/8" to 2-5/8" thick. Secure, tamper-resistant. Solid brass body; glass lens. Simple installation only a 1/2" hole required. Suggested installation height: 60" from floor. Trim washer available, 3/4" x.032" thick. 701 meets NSI/HM L23173 U701 meets NSI/HM L23222 U701 is UL Listed 90 minute fire doors. inishes Ives Number HM xterior Hardware 6

140 oor Knockers Meets NSI/HM L23151 Meets NSI/HM L Knocker Only Knocker made from forged brass. Only available in Schlage arded pak Length: 8-1/2" Width: 4-1/8" Projection: 1" Mounting Hole enter-to-enter: 5" inishes Ives Number HM Knocker Only U Knocker with U700 Viewer U Knocker with U701 Viewer Knocker made from forged brass and U for door thickness 7/8" 1-9/16" and U for door thickness 1-5/8" 2-1/8" Length: 5-15/16" Width: 3" Projection: 1-1/16" Mounting Hole enter-to-enter: 3-15/16" inishes Ives Number * HM * not available on viewer, only available in Schlage arded Only 3, 15, 26 and 716 knockers are available with viewer. 3 is furnished with 4 (606) viewer, 716 is furnished with 10 viewer, 15 (619) is furnished with a 636 viewer. 7 xterior Hardware 7

141 oor Knockers 8 xterior Hardware 620 Magazine Size Letter ox Plate with Standard (Open) ack Plate Spring-loaded front plate Sex olt mounting available, order separately finish. Meets NSI/HM L26031 Overall Size: 13" Wide x 3-9/16" High Plate Opening: 11" x 2" High inishes brass Ives Number * HM inishes aluminum Ives Number P28 HM 628 * not available in U700 Schlage arded 601 Sleeve for use with Letter ox Plate Made of stainless steel. or 1-3/4" hollow core doors. 8

142 House Numbers S2-30 X 6 Heritage House Number Made from solid brass. Schlage arded Height: 4" inishes brass Ives Number HM Storm oor Latch or wood storm doors 7/8" to 1-1/8" thick. Reversible: fits right or left hand, inswinging or outswinging doors. Security lock feature operates from inside rose. Solid brass safety strike assures latching and is designed to compensate for air pressure build-up between doors. Made from wrought brass. ackset: 1-3/4" Rose iameter: 1-7/8" Knob iameter: 1-3/4" Knob Projection: 2" Lever Length: 1-3/4" Lever Projection: 1-7/8" inishes brass Ives Number HM xterior Hardware 9

143 rash 25 Screen oor Pull ast aluminum or epoxy-coated alumimum lso used as a window lift, drawer or utility pull Length 4-7/8" Meets NSI/HM , L12231, Projection 1-5/32" Mounting holes 4-1/8" center to center Meets NSI/HM , L12231, inishes Ives Number W - HM S115 rash Stop Specially designed for full-size exterior doors. Tear resistant, grey vinyl cover. Heavy duty compression spring assembled to both ends of chain and end brackets. Packed with sheet metal screws. ast rass brackets with solid, welded steel chain. Optional sex bolt mounting available in US26 (626) only. racket Size: 1-9/16" x 1-9/16" vailable Lengths: 20-1/2" Recommended for 30" oor Width (Product No. S115-20) 25-1/2" Recommended for 36" oor Width (Product No. S115-25) 30-1/2" Recommended for 42" oor Width (Product No. S115-30) 10 xterior Hardware inishes Ives Number US10 US26 HM

144 Miscellaneous oor Hardware Table Of ontents page Hooks & rackets 059 Handrail racket Handrail racket Handrail racket oat & Hat Hook oat & Hat Hook oat & Hat Hook oat & Hat Hook oat & Hat Hook eiling Hook Wardrobe Hook Wardrobe Hook loset Pole Socket loset Pole Socket Window Hardware 07 Window Lock Side Window Lock ar Window Lift asement astener asement astener asement djuster Hobby Hardware 78 Hook and Staple Hobbyist arrel olt , 9031 Middle utt Hinge Middle utt Hinge road utt Hinge ecorative Hinge , 9072 ecorative Hinge ecorative Hasp Hasp Hook with Hasp Support Hinge riction Lid Support , 9212 ecorative orner racket racket raw atch hest Handle abinet/loset Hardware 2 lbow atch lush Pull inger Pull lush Pull lush Pull lush Pull lush Pull Slide oor dge Pull Pocket Sliding oor olt Sliding oor Pull Sliding oor Pull xterior Hardware 1 1

145 Hand Rail rackets and Hooks Meets NSI/HM L13061 for brass and L33061 for aluminum Meets NSI/HM L13061 for brass and L33061 for aluminum 059 Hand Rail racket Made from solid brass, cast aluminum or epoxy-coated aluminum. Large faceplate for secure attachment to wall. eatures solid construction for increased strength. ase: 2-1/4" High x 1-3/8" Wide ase to enter of Rail: 2-7/16" inishes brass Ives Number HM inishes aluminum Ives Number LK -W HM inishes zinc Ives Number Z Hand Rail racket Made from cast brass or cast aluminum. Large faceplate for secure attachment to wall. eatures solid construction for increased strength. luminum ase: 2-13/16" High x 1-1/2" Wide rass ase: 2-15/16" High x 1-1/2" Wide ase to enter of Rail: 2-3/4" inishes brass Ives Number HM inishes aluminum Ives Number HM xterior Hardware 2 Meets NSI/HM , L Hand Rail racket or use on commercial applications. xceeds OSH and HM strength test requirements. Packed with square head iron lag screw, expansion shield and screws. ast luminum construction. ase iameter: 3-1/8" ase to Rail enter: 3-1/8" inishes aluminum Ives Number HM

146 Hooks Meets NSI/HM L oat & Hat Hook Wide body design is ideal for public buildings, schools, dormitories, etc., where hook must withstand unusual stress and strain. Made from cast aluminum. ase: 1-1/2" High x 7/8" Wide Projection: 2-1/2" inishes aluminum Ives Number HM Meets NSI/HM L13113 for brass and L33113 for aluminum. 571 oat & Hat Hook ll-purpose hook in traditional design. Made from cast brass, cast aluminum, or epoxy-coated aluminum. ase: 1-3/4" High x 1-1/4" Wide Projection: 3" inishes brass Ives Number * HM inishes aluminum Ives Number W -LK HM inishes zinc Ives Number Z619 HM * only available in Schlage arded or Slim-Pak of oat & Hat Hook Step-up decorative version of the traditional all-purpose hook. Ideal for locations where additional strength is required. Made from cast brass or cast aluminum. rass ase: 1-1/2" High x 1-5/16" Wide luminum ase: 1-5/8" High x 1-5/16" Wide Projection: 3" inishes brass Ives Number HM inishes aluminum Ives Number xterior Hardware 3 HM

147 Hooks Meets NSI/HM L13113 for brass and L33113 for aluminum Meets NSI/HM L oat & Hat Hook ecorative design is ideal for commercial and residential installations. Made from cast brass, cast aluminum or epoxy-coated aluminum. ase: 1-5/8" High x 1-3/4" Wide Projection: 3-3/4" Overall Height, rass: 4-3/4" Overall Height, luminum: 5" inishes brass Ives Number HM inishes aluminum Ives Number HM oat & Hat Hook specially designed to accommodate large hats. Made from solid brass or cast aluminum. ase: 2-1/4" High x 1-3/8" Wide Projection: 3-5/8" Overall Height: 5-3/4" inishes aluminum Ives Number HM xterior Hardware 580 eiling Hook Ideal for use in closets, attached to underside of shelves, or in storage lockers. Made from cast brass or cast aluminum. ase: 1" High x 1-7/8" Wide Projection: 2-1/4" 4 inishes Ives Number HM

148 Hooks 581 Wardrobe Hook ompact hook is perfect where space is limited, such as behind doors where low profile is needed. Made from cast brass, cast aluminum or epoxy-coated aluminum. ase, rass/luminum: 1-1/4" High x 1-1/4" Wide ase, Zinc: 1-1/2" High x 3/4" Wide Projection, rass: 1-11/16" Projection, luminum, Zinc: 1-5/8" inishes brass Ives Number * HM * only available in Schlage arded inishes aluminum Ives Number LK -W HM inishes zinc (narrow base) Ives Number Z619 HM 582 ouble Wardrobe Hook ompact double hook is perfect where space is limited, such as behind doors where low profile is needed. Made from cast brass, cast aluminum or epoxy-coated aluminum. ase, rass: 1-1/8" High x 1-1/4" Wide ase, luminum: 1-1/16" Hgh x 1-3/16 Wide ase, Zinc: 1-5/8" High x 7/8" Wide Projection, rass: 1" Projection, luminum, Zinc: 1-3/32" inishes brass Ives Number * HM inishes aluminum Ives Number W -LK HM inishes zinc (narrow base) Ives Number Z619 HM * only available in Schlage arded or Slim-Pak of 25 xterior Hardware 5 5

149 Window Hardware SP585 loset Pole Sockets lange design prevents accidental knock out of pole. Made from wrought steel. ccommodates pole or pipe with outside diameter of 1-3/8". Packed in pairs. inishes Ives Number 3 HM 632 SP586 inish White Plastic loset Pole Sockets Made from a heavy duty plastic for long life and extra strength. Single screw mounting. ccommodates pole or pipe with outside diameter of 1-3/8". Packed in pairs. xterior Hardware 6 Meets NSI/HM Window Lock esigned low to the sash for superior strength and greater resistance to breakage. Vertical and horizontal camming action for snug, non-rattling fit. Heavy gauge springs provide long-wearing action. Made from solid brass, aluminum, or epoxy coated aluminum. ase: 15/16" x 2-9/16" Strike: 5/8" x 2-9/16" inishes brass Ives Number * HM inishes aluminum Ives Number 3 5* W -LK HM * only available in Schlage arded or Slim-Pak of 25 6