SEISMIC DESIGN GUIDE FOR FIRE SPRINKLER COMPONENTS EDITION 2.0 FOR NFPA COLOR CODED PRE-STRETCHED BREAK STRENGTH CERTIFIED
|
|
- Harry Baldwin
- 6 years ago
- Views:
Transcription
1 SEISMIC DESIGN GUIDE FOR FIRE SPRINKLER COMPONENTS EDITION 2.0 FOR COLOR CODED PRE-STRETCHED BREAK STRENGTH CERTIFIED
2 PREFACE Whether it s drawn stainless steel wire, miniature or aircraft cable, wire rope, Seismic Wire Rope assemblies, fittings or tools, Loos & Co. Inc. can deliver. We have developed, over the last fifty eight years, the technical capabilities essential in providing such materials to such varied industries as aerospace, data processing, automotive, aircraft and farm equipment. Special products have been designed and made for ocean research, mineral exploration and military markets as well as many other scientific and industrial applications. Technical competence, combined with modern production equipment and rigid quality control guarantee on time delivery of our wire, cable and cable related products, made to the most exacting specifications. Loos & Co. has earned its reputation by continuously meeting and exceeding the increasingly stringent safety requirements of the aerospace industry. We have taken that level of safety, combined with 50+ years of knowledge and expertise and applied this methodology to our Seismic Bracing system. Loos & Co. has been providing Seismic Bracing cable and hardware since What we have seen over the past 23 years is an evolution from what was once confusion and misconception to an industry that has gone above and beyond to embrace nationally accepted codes and standards. Loos & Co. has taken this position to the next level, by incorporating most, if not all of the certifications required to make our Seismic Bracing the most cost effective, most certified and accepted bracing system on the market. Loos & Co. certifications include: * Third party listed (UL & ICC ES) for use in complying with NFPA 13 for fire sprinkler systems. * Third party listed (ICC ES) for use in complying with the International Building Code (IBC) * Are third party tested/listed to verify that cable assemblies, including fittings, maintain the nominal breaking strength per ASCE 19, as required by IBC, ASCE 7 & NFPA 13 *Have swaged end fittings as required by the 2012 IBC per ASCE 19-10, which does not permit wedge or clip type fittings. *Certify the minimum breaking strength of the sway bracing assemblies. *Comply with NFA 13, ASCE 19, the IBC and ASCE 7. *Are listed by the FBC for system compatibility with CPVC pipe. In this guide, you will find all of the specifications, descriptions and applicable drawings for all of the Seismic products Loos & Co. offers. This will allow the user to identify and specify the proper components to satisfy the code requirements of the local authority having jurisdiction (AHJ). Thank you for your interest in our Seismic Bracing System manufactured by Loos & Co. Inc. Loos & Co., Inc. - ware Division 1.2
3 APPLICATION OF THIS PUBLICATION In this publication you will find information regarding proper installation techniques and guidelines applicable to Loos & Co. Seismic Bracing System for meeting existing codes and standards. It has been compiled using proven engineering ethics and principles developed over the past 23 years. Final accountability for approving specific designs, code interpretations and/or installations rests with the engineer responsible for the specific design and/or the agency or authority having jurisdiction (AHJ). Loos & Co. Inc. and/or contributors to this publication assume no liability for the specific installation of its products or the design, application, approval or interpretation of the requirements or guidelines contained in this publication. Users of this publication are encouraged to confer with certified design Engineers (P.E.) as well as all applicable Federal, State and local a regulations or requirements for specific installations. REPRINT PERMISSION RESTRICTIONS Permission is granted to government and private sector users of this publication to reproduce unaltered conceptual drawings from this publication for their use relating to the specific design, specification, installation or approval of Loos & Co. Seismic Bracing. Reproduction for the purpose of its sale is prohibited. Any other use or reproduction of this publication shall be first approved in writing by Loos & Co. Inc. Liability for the specific application of such information, including errors or omissions in reproduction is solely the responsibility of the party reproducing such material. GENERAL INTRODUCTION Loos & Co. Seismic Design Guide will assist you in the design and installation of our Seismic Bracing System. All of the materials and products presented have been designed and tested to exceed the requirements set forth in NFPA 13. In Fact, the provisions of NFPA 13 directly provide for the use of Loos & Co. UL Listed Seismic Bracing. Loos & Co. has been providing our Seismic Bracing since 1993 in structures located all over the world, both for new and retro-fit buildings. This Design Guide can be used in conjunction with our New Seismic Design Calculator. (Downloadable for free on our Website ) Our Seismic Design Calculator will allow the user to enter all the details for fire sprinkler installations from the building blueprints then print out of the completed NFPA 13 form with all of the calculation preapproved, ready to submit to your local AHJ. As an added bonus, our Seismic Design Calculator software will also generate a Bill of material and all applicable drawings. Loos & Co., Inc. - ware Division 1.3
4 Locoloc #0-3-SBHS Handswager Preferred tool for Swaging Gold cable #G03-CBL A well-made, economical handswaging tool for swaging #GO3 cable sleeves, our most popular cable size. Loos offers the correct tools to use in swaging our zinc-plated oval sleeves. Using the correct tool and following proper swaging instructions will ensure proper cable connections that actually exceed the breaking strength of the cable. Length: 12" Use: For size #GO3 (GOLD) cable only. OPERATION INSTRUCTIONS: To open tool squeeze handles hard or push release lever (Figure 1) forward while squeezing handles to relieve tension. Figure 1 Figure 2 Figure 3 1. Place the sleeve on the cable and make a loop around the item to which you are securing the cable. 2. Next, insert cable end through the sleeve and at least 1/8" or more beyond (Figure 3). 3. While holding sleeve in place, swage one compression. Move over and swage (second compression). Two compressions are required. The tool won't release until compression is complete. (Figure 2) 4. Check sleeve for proper after swage diameter with gauge provided (Figure 7). The clamping action of the ratchet allows the sleeve to be held by the tool before completing the swage. This allows for the user to adjust the position of the sleeve on the cable. 5. After swaging, excess cable may be trimmed off with our FELCO C7 cutters below. Figure 7 Loos & Co., Inc. - ware Division 1.4
5 Locoloc #3-346-SB Handswager Used for #GO3-CBL, #OR4-CBL, #GR6-CBL A well-made, economical handswaging tool for swaging cable sleeves. Loos offers the correct tools to use in swaging our zinc-plated oval sleeves. Using the correct tool and following proper swaging instructions included with each tool will ensure proper cable connections that actually exceed the breaking strength of the cable. Length: 26" Use: Two-handed tool for size #GO3 (GOLD), #OR4 (ORANGE) and #GR6 (GREEN) cables. Each Loos & Co. #3-346SB swaging tool is designed to work with #3, #4, and #6 Zinc-Plated Copper Oval Sleeves. For use only on Loos & Co. Seismic Bracing sizes #GO3, #OR4, and #GR6. You will not obtain proper performance or meet UL standards if you do not use the proper Loos & Co. swaging tool and sleeve combination. Place sleeve to be compressed in proper size groove in swaging tool by matching cable color to colored dot next to groove in tool. A length of cable equal to the cable diameter should extend beyond the length of sleeve to achieve maximum holding. (See arrow in Figure 4). Finished sleeve should look like this. Be sure sleeves have been compressed the proper number of times. See below for proper # of compressions. Size Zinc-Plated Copper Oval Sleeve #GO3 (Gold) 2 #OR4 (Orange) 2 #GR6 (Green) 3 Figure 4 Keep jaws of swaging tool at right angles to the sleeve to be compressed, making sure the sleeve is aligned in the jaw grooves. Close tool completely. Tool handles should snap shut indicating complete closure. After swaging, excess cable may be trimmed off with our FELCO C7 cutters. Figure 5 Use the swaging gauge provided with the tool to check proper after swage diameter of sleeve. Compressed sleeve should slide freely into corresponding size and color slot in gauge. (Figure 5) Loos & Co., Inc. - ware Division 1.5
6 Locoloc HC-3010-SB Battery Handswager A well-made and powerful, state-of-the-art battery-powered swaging tool. This newest technology eliminates the need to swage Loos zinc-plated oval sleeves by hand. This is especially helpful when a large number of brace connections are required for the job. Kit comes with complete with two long-lasting, fast charge lithiumion batteries, I hour quick charger and handy carrying case so you can be sure to have strong portable power at all times. Use: For size #GO3 (GOLD), #OR4 (ORANGE) and #GR6 (GREEN) cable sleeves. Length: 22" Height: 4" Weight: 13 lbs. OPERATING INSTRUCTIONS Place the cable sleeve to be crimped in the appropriate cavity. Press on the Grey forward trigger to crimp the sleeve onto the cable. An audible click advises when the swage (crimp) is completed. Open the jaws of the tool by pressing the Black retract trigger, you may now crimp another sleeve or you may start another crimp cycle of the tool. Number of Compressions size Zinc-plated Copper oval sleeves #GO3 (GOLD) 2 #OR4 (ORANGE) #GR6 (GREEN) 2 3 Figure 1 Figure 2 Figure 3 Finished sleeve should look like (Figure 2) on Gold cable. Be sure sleeves have been compressed the proper number of times. (See Number of Compressions Figure 1). Using the swaging gauge provided with the tool to check proper after swage diameter of sleeve. Compressed sleeve should slide into size slot in gauge: GO (Gold), OR (Orange) and GR (Green). Sleeves elongate after compression. To assure maximum holding allow the end of the cable to extend beyond the sleeve after it is compressed. Select the proper cavity size for the sleeve to be swaged. Use only #GO3 sleeves with #GO3 cavity, #OR4 sleeve with #OR4 cavity and so on. For lap splices at least two oval sleeves should be used. Loos & Co., Inc. - ware Division 1.6
7 FELCO C7 CABLE CUTTER Loos & Co. offers the complete line of Swiss-made FELCO Brand Cutters. FELCO cutters are recognized around the world for their precision manufacture and cutting capabilities. Lightweight enough for overhead cutting yet strong enough for underwater work. Plastic-coated handles afford a firm, comfortable grip. A cable when crushed or deformed in cutting is difficult to use with fittings. These cable cutters, with unique triangular jaws, never leave a frayed end. Capacity: 5/32" on stainless steel diameter and smaller. For use on #GO3-CBL (GOLD) and #OR4-CBL (ORANGE) cable. Length: 7.5" / 190 mm Weight: 9.5 oz. / 270g FELCO C9 CABLE CUTTER FELCO cutters are recognized around the world for their precision manufacture and cutting capabilities. Lightweight enough for overhead cutting yet strong enough for underwater work. Plastic-coated handles afford a firm, comfortable grip. Replacement parts are available from stock. All cutters tested before leaving the factory. Fills the gap between C7 and C12 - cuts 1/4" steel cable. Ideal for the tool kit. All cutters available from stock. Capacity: Cuts 1/4" steel cable. For use on #GR6-CBL (GREEN) and #BL8-CBL (BLACK) cable. Length: 13" / 325mm Weight: 1.5 lbs. / 750g High-Strength Blades Hardened and tempered blades for cutting the strongest of cables. Triangular Cutting Action FELCO's innovative triangular cut allows you to progressively cut cable wires and at the same time avoid squashing of strands. Thanks to this feature, it is generally not necessary to tie the cable before the cut. Forged Aluminum Handles Lightweight, strong and sturdy thanks to special aluminum alloys and advanced precision forging methods. Loos & Co., Inc. - ware Division 1.7
8 Description of Standard Brace Kit Part Numbers 1. Choose your brace type: Detailed Kit Part Numbers Brace Type Description To Fit Fastener Code 2 Two-Way All All 4 Four-Way All 00, 2B, 3B, 4B, 5B 2: Choose the cable that best fits your load requirement: Code Description Fastener Code GO3 Gold, 600 lb. Load Rating 00, 2S, 2B, 3S, 3B OR4 Orange, 1100 lb. Load Rating 00, 2S, 2B, 3S, 3B, 4S, 4B GR6 Green, 2667 lb. Load Rating 00, 3S, 3B, 4S, 4B BL8 Black, 4400 lb. Load Rating 00, 5S, 5B 3. Choose the fastener that best fits your requirement: Fastener Code Description To Fit 00 No Stake Eye, Loop GO, OR, GR, BL 2S 1/4 Straight Stake Eye GO, OR 2B 1/4 45 Stake Eye GO, OR 3S 3/8 Straight Stake Eye GO, OR, GR 3B 3/8 45 Stake Eye GO, OR, GR 4S 1/2 Straight Stake Eye OR, GR 4B 1/2 45 Stake Eye OR, GR 5S 5/8 Straight Stake Eye BL 5B 5/8 45 Stake Eye BL 4. Choose desired brace length: Length Code Description To Fit 01 1 foot (+4 ft. extra) All 04 4 feet (+4 ft. extra) All 07 7 feet (+4 ft. extra) All feet (+4 ft. extra) All feet (+4 ft. extra) All Loos & Co., Inc. - ware Division 1.8
9 Index SECTION 1 GENERAL INFORMATION 1.2 Preface 1.3 Application 1.3 Reprint Permission Restrictions 1.3 General Introduction Hand Tool Information 1.8 Description of Kit Part Numbers SECTION 2 PRODUCTS Seismic Bracing 2.5 Zinc-Plated Oval Sleeves Seismic Attachment Fitting (SAF) Series Seismic Attachment Fitting Retrofit (SAFR) Series Seismic Attachment Fitting 2 (SAF2) Series Seismic Attachment Fitting Retrofit 2 (SAFR2) Series Low-Pry Fitting (LPF) Series SECTION 3 INSTRUCTIONS 3.1 Lateral Bracing Installation 3.2 Longitudinal Bracing Installation Way Bracing Installation 3.4 Through Bolts in Wood Angles A, B, and C 3.5 Lag Bolts in Wood Angles A, B, and C 3.6 Wedge Anchors in 3000 psi Lightweight Concrete Filled Metal Decking Angles A, B, and C 3.7 Wedge Anchors in 3000 psi Normal Weight Cracked Concrete Angles A, B, and C 3.8 Undercut Anchors in 3000 psi Normal Weight Concrete Angles A, B, and C 3.9 Wedge Anchors in 3000 psi Lightweight Cracked Concrete Angles A, B, and C Loos & Co., Inc. - ware Division 1.9
10 3.10 Wedge Anchors in 4000 psi Normal Weight Cracked Concrete Angles A, B, and C 3.11 Wedge Anchors in 6000 psi Normal Weight Cracked Concrete Angles A, B, and C 3.12 Connections to Steel Angles A, B, and C 3.13 Through Bolts in Wood Angles D, E, and F 3.14 Lag Bolts in Wood Angles D, E, and F 3.15 Wedge Anchors in 3000 psi Normal Weight Cracked Concrete Angles D, E, and F 3.16 Undercut Anchors in 3000 psi Normal Weight Concrete Angles D, E, and F 3.17 Wedge Anchors in 3000 psi Lightweight Cracked Concrete Angles D, E, and F 3.18 Wedge Anchors in 4000 psi Normal Weight Cracked Concrete Angles D, E, and F 3.19 Wedge Anchors in 6000 psi Normal Weight Cracked Concrete Angles D, E, and F 3.20 Connections to Steel Angles D, E, and F 3.21 Through Bolts in Wood Angles G, H, and I 3.22 Lag Bolts in Wood Angles G, H, and I 3.23 Wedge Anchors in 3000 psi Normal Weight Cracked Concrete Angles G, H, and I 3.24 Undercut Anchors in 3000 psi Normal Weight Concrete Angles G, H, and I 3.25 Wedge Anchors in 3000 psi Lightweight Cracked Concrete Angles G, H, and I 3.26 Wedge Anchors in 4000 psi Normal Weight Cracked Concrete Angles G, H, and I 3.27 Wedge Anchors in 6000 psi Normal Weight Cracked Concrete Angles G, H, and I 3.28 Connections to Steel Angles G, H, and I 3.29 Looped Around Top Member of Bar Joist Angles A, B, and C Loos & Co., Inc. - ware Division 1.10
11 Seismic Bracing Bulk Spool - Size #3 (Gold) Certified Minimum Break Strength (lbs) Allowable Load at 90 (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Min. Diameter (in.) Max. Diameter (in.) Number of Wires Nom. Dia. of Wires (in.) Min. Stress at 0.7% Extension Under Load Min. Ultimate Tensile Strength to ,000 PSI 300,000 PSI Applied Load (lbs) Applied Load (% of Min. Break Strength) % Elongation at Applied Load Modulus of Elasticity 92 10% 0.15% 12.7 x % 0.28% 14.6 x % 0.40% 15.8 x % 0.48% 17.7 x % 0.59% 18.5 x % 0.74% 17.3 x %* 0.84% 17.1 x 10 6 *66.67% is equal to the allowable working load (break strength 1.5) ESL-1004 & Industrial Boulevard Naples, Florida USA T e l e p h o n e: (800) Fax: (239) info@loosnaples.com Web: Specialists in wire rope hardware and tools See our catalog in the Thomas Register Loos & Co., Inc. - ware Division 2.1
12 Seismic Bracing Bulk Spool - Size #4 (Orange) Certified Minimum Break Strength (lbs) Allowable Load at 90 (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Min. Diameter (in.) Max. Diameter (in.) 1,700 1, Number of Wires Nom. Dia. of Wires (in.) Min. Stress at 0.7% Extension Under Load Min. Ultimate Tensile Strength to ,000 PSI 300,000 PSI Applied Load (lbs) Applied Load (% of Min. Break Strength) % Elongation at Applied Load Modulus of Elasticity % 0.17% 11.0 x % 0.30% 13.4 x % 0.42% 14.7 x % 0.52% 16.8 x % 0.64% 17.1 x % 0.75% 17.0 x %* 0.84% 17.5 x 10 6 *66.67% is equal to the allowable working load (break strength 1.5) ESL-1004 & Industrial Boulevard Naples, Florida USA T e l e p h o n e: (800) Fax: (239) info@loosnaples.com Web: Specialists in wire rope hardware and tools See our catalog in the Thomas Register Loos & Co., Inc. - ware Division 2.2
13 Seismic Bracing Bulk Spool - Size #6 (Green) Certified Minimum Break Strength (lbs) Allowable Load at 90 (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Min. Diameter (in.) Max. Diameter (in.) 4,200 2,100 1,050 1,485 1, Number of Wires Nom. Dia. of Wires (in.) Min. Stress at 0.7% Extension Under Load Min. Ultimate Tensile Strength to ,000 PSI 300,000 PSI Applied Load (lbs) Applied Load (% of Min. Break Strength) % Elongation at Applied Load Modulus of Elasticity % 0.17% 12.8 x % 0.31% 14.6 x ,260 30% 0.44% 15.8 x ,680 40% 0.56% 17.1 x ,100 50% 0.69% 17.4 x ,520 60% 0.82% 17.4 x , %* 0.93% 17.3 x 10 6 *66.67% is equal to the allowable working load (break strength 1.5) ESL-1004 & Industrial Boulevard Naples, Florida USA T e l e p h o n e: (800) Fax: (239) info@loosnaples.com Web: Specialists in wire rope hardware and tools See our catalog in the Thomas Register Loos & Co., Inc. - ware Division 2.3
14 Seismic Bracing Bulk Spool - Size #8 (Black) Certified Minimum Break Strength (lbs) Allowable Load at 90 (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Allowable Load at (lbs) Min. Diameter (in.) Max. Diameter (in.) 7,000 4,600 2,300 3,253 3, Number of Wires Nom. Dia. of Wires (in.) Min. Stress at 0.7% Extension Under Load Min. Ultimate Tensile Strength to ,000 PSI 290,000 PSI Applied Load (lbs) Applied Load (% of Min. Break Strength) % Elongation at Applied Load Modulus of Elasticity % 0.20% 12.6 x ,400 20% 0.34% 14.6 x ,100 30% 0.47% 15.9 x ,800 40% 0.60% 16.3 x ,500 50% 0.72% 17.2 x ,200 60% 0.85% 17.5 x , %* 0.94% 17.7 x 10 6 *66.67% is equal to the allowable working load (break strength 1.5) ESL-1004 & Industrial Boulevard Naples, Florida USA T e l e p h o n e: (800) Fax: (239) info@loosnaples.com Web: Specialists in wire rope hardware and tools See our catalog in the Thomas Register Loos & Co., Inc. - ware Division 2.4
15 9P62 ESL-1004 ESL-1007 All Zinc Plated Oval Sleeves supplied by Loos & Co. Inc. are in full compliance with the requirements of Military Specification MS51844, and are certified to maintain the break strength of the cable to which they are applied (for 3 x 7, 7 x7, 7 x 19, and 6 x 19 construction). Loos & Co., Inc. - ware Division 2.5
16 SAF SERIES (Structural Attachment Fitting) Patent # 62/239,394 Loos & Co., Inc. - ware Division 2.6
17 9P62 SAF-1/4 ESL-1004 ESL-1007 Mount Fastener Mount The SAF-1/4 is designed for use in attaching Seismic Bracing to steel structural members. The limitations of use are governed by the fastener diameter as a 1/4 inch (6 mm) fastener is only listed for use with steel as per NFPA-13. Will accept both metric and imperial fasteners. The cable mount will accept Gold, Orange, and Green cables. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.7
18 9P62 SAF-3/8 ESL-1004 ESL-1007 Mount Fastener Mount The SAF-3/8 is designed for use in attaching Seismic Bracing to a steel, concrete, or wood structural member. The 3/8 inch (10 mm.) will accept lag bolts, bolts, and concrete anchors in both metric and imperial sizes. The cable mount will accept Gold, Orange, and Green cable. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.8
19 9P62 SAF-1/2 ESL-1004 ESL-1007 Mount Fastener Mount The SAF-1/2 is designed for use in attaching Seismic Bracing to a steel, concrete, or wood structural member. The 1/2 inch (13 mm) will accept lag bolts, bolts, and concrete anchors in both metric and imperial sizes. The cable mount will accept Gold, Orange, and Green cable. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.9
20 9P62 SAF-5/8 ESL-1004 ESL-1007 Mount Fastener Mount The SAF-5/8 is designed for use in attaching Seismic Bracing to a steel, concrete, or wood structural member. The 5/8 inch (16 mm) will accept lag bolts, bolts, and concrete anchors in both metric and imperial sizes. The cable mount will accept Gold, Orange, and Green cable. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.10
21 9P62 SAF-3/4 ESL-1004 ESL-1007 Mount Fastener Mount The SAF-3/4 is designed for use in attaching Seismic Bracing to a steel, concrete, or wood structural member. The 3/4 inch (20 mm) will accept lag bolts, bolts, and concrete anchors in both metric and imperial sizes. The cable mount will accept Gold, Orange, and Green cable. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.11
22 9P62 SAF-7/8 ESL-1004 ESL-1007 Mount Fastener Mount The SAF-7/8 is designed for use in attaching Seismic Bracing to a steel, concrete, or wood structural member. The 7/8 inch (22 mm) will accept lag bolts, bolts, and concrete anchors in both metric and imperial sizes. The cable mount will accept Gold, Orange, and Green cable. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.12
23 9P62 SAF-1 ESL-1004 ESL-1007 Mount Fastener Mount The SAF1 is designed for use in attaching Seismic Bracing to a steel, concrete, or wood structural member. The1 inch (24 mm) will accept lag bolts, bolts, and concrete anchors in both metric and imperial sizes. The cable mount will accept Gold, Orange, and Green cable. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.13
24 9P62 SAF-11/4 ESL-1004 ESL-1007 Mount Fastener Mount The SAF1 1/4 is designed for use in attaching Seismic Bracing to a steel, concrete, or wood structural member. The11/4 inch (32 mm) will accept lag bolts, bolts, and concrete anchors in both metric and imperial sizes. The cable mount will accept Gold, Orange, and Green cable. The SAF maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF may be used at both ends of the cable for anchoring equipment. SAF's are offered in eight different mounting sizes,saf-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF 1 1/4. Loos & Co., Inc. - ware Division 2.14
25 SAFR SERIES Structural Attachment Fitting, Retrofit Patent # 62/239,394 Loos & Co., Inc. - ware Division 2.15
26 ESL-1004 ESL-1007 SAFR-1/4 Mount Fastener Mount The SAFR-1/4 is designed as a retrofit Seismic Anchoring Fitting for use with pre-existing equipment and systems that require seismic bracing. The fitting is slotted to allow an existing fastener to be loosened, and the SAFR positioned without removal of the fastener. The SAFR maintains the rated breaking strength of size 3 (Gold) and 4 (Orange) cable without the need of a thimble. The SAFR may be used at both ends of the cable for anchoring equipment. SAFR's are offered in four different fastener mounting sizes,safr-1/4, SAFR-3/8, SAFR-1/2, and SAFR-5/8. Loos & Co., Inc. - ware Division 2.16
27 ESL-1004 ESL-1007 SAFR-3/8 Mount Fastener Mount The SAFR-3/8 is designed as a retrofit Seismic Anchoring Fitting for use with pre-existing equipment and systems that require seismic bracing. The fitting is slotted to allow an existing fastener to be loosened, and the SAFR positioned without removal of the fastener. The SAFR maintains the rated breaking strength of size 3 (Gold) and 4 (Orange) cable without the need of a thimble. The SAFR may be used at both ends of the cable for anchoring equipment. SAFR's are offered in four different fastener mounting sizes,safr-1/4, SAFR-3/8, SAFR-1/2, and SAFR-5/8. Loos & Co., Inc. - ware Division 2.17
28 ESL-1004 ESL-1007 SAFR-1/2 Mount Fastener Mount The SAFR-1/2 is designed as a retrofit Seismic Anchoring Fitting for use with pre-existing equipment and systems that require seismic bracing. The fitting is slotted to allow an existing fastener to be loosened, and the SAFR positioned without removal of the fastener. The SAFR maintains the rated breaking strength of size 3 (Gold) and 4 (Orange) cable without the need of a thimble. The SAFR may be used at both ends of the cable for anchoring equipment. SAFR's are offered in four different fastener mounting sizes,safr-1/4, SAFR-3/8, SAFR-1/2, and SAFR-5/8. Loos & Co., Inc. - ware Division 2.18
29 ESL-1004 ESL-1007 SAFR-5/8 Mount Fastener Mount The SAFR-5/8 is designed as a retrofit Seismic Anchoring Fitting for use with pre-existing equipment and systems that require seismic bracing. The fitting is slotted to allow an existing fastener to be loosened, and the SAFR positioned without removal of the fastener. The SAFR maintains the rated breaking strength of size 3 (Gold) and 4 (Orange) cable without the need of a thimble. The SAFR may be used at both ends of the cable for anchoring equipment. SAFR's are offered in four different fastener mounting sizes,safr-1/4, SAFR-3/8, SAFR-1/2, and SAFR-5/8. Loos & Co., Inc. - ware Division 2.19
30 SAF2 SERIES Structural Attachment Fitting, 2 Way Patent #62/239,394 Loos & Co., Inc. - ware Division 2.20
31 SAF2-1/4 Mount Fastener Mount The SAF2-1/4 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports for attachment to a steel, concrete, or wood structural member. The 1/4 inch (6 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, Orange, and Green cable and are ideal for 2-way bracing. The SAF2 maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF2 may be used at both ends of the cable for anchoring equipment. SAF2's are offered in six different mounting sizes,saf2-1/4, SAF2-3/8, SAF2-1/2, SAF2-5/8, SAF2-3/4, and SAF2-7/8. Loos & Co., Inc. - ware Division 2.21
32 SAF2-3/8 Mount Fastener Mount The SAF2-3/8 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports for attachment to a steel, concrete, or wood structural member. The 3/8 inch (10 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, Orange, and Green cable and are ideal for 2-way bracing. The SAF2 maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF2 may be used at both ends of the cable for anchoring equipment. SAF2's are offered in six different mounting sizes,saf2-1/4, SAF2-3/8, SAF2-1/2, SAF2-5/8, SAF2-3/4, and SAF2-7/8. Loos & Co., Inc. - ware Division 2.22
33 SAF2-1/2 Mount Fastener Mount The SAF2-1/2 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports for attachment to a steel, concrete, or wood structural member. The 1/2 inch (13 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, Orange, and Green cable and are ideal for 2-way bracing. The SAF2 maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF2 may be used at both ends of the cable for anchoring equipment. SAF2's are offered in six different mounting sizes,saf2-1/4, SAF2-3/8, SAF2-1/2, SAF2-5/8, SAF2-3/4, and SAF2-7/8. Loos & Co., Inc. - ware Division 2.23
34 SAF2-5/8 Mount Fastener Mount The SAF2-5/8 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports for attachment to a steel, concrete, or wood structural member. The 5/8 inch (16 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, Orange, and Green cable and are ideal for 2-way bracing. The SAF2 maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF2 may be used at both ends of the cable for anchoring equipment. SAF2's are offered in six different mounting sizes,saf2-1/4, SAF2-3/8, SAF2-1/2, SAF2-5/8, SAF2-3/4, and SAF2-7/8. Loos & Co., Inc. - ware Division 2.24
35 SAF2-3/4 Mount Fastener Mount The SAF2-3/4 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports for attachment to a steel, concrete, or wood structural member. The 3/4 inch (20 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, Orange, and Green cable and are ideal for 2-way bracing. The SAF2 maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF2 may be used at both ends of the cable for anchoring equipment. SAF2's are offered in six different mounting sizes,saf2-1/4, SAF2-3/8, SAF2-1/2, SAF2-5/8, SAF2-3/4, and SAF2-7/8. Loos & Co., Inc. - ware Division 2.25
36 SAF2-7/8 Mount Fastener Mount The SAF2-7/8 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports for attachment to a steel, concrete, or wood structural member. The 7/8 inch (22 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, Orange, and Green cable and are ideal for 2-way bracing. The SAF2 maintain the rated break strength of size 3 (Gold), 4 (Orange), and 6 (Green) cable without the need of a thimble. The SAF2 may be used at both ends of the cable for anchoring equipment. SAF2's are offered in six different mounting sizes,saf2-1/4, SAF2-3/8, SAF2-1/2, SAF2-5/8, SAF2-3/4, and SAF2-7/8. Loos & Co., Inc. - ware Division 2.26
37 SAFR2 SERIES Structural Attachment Fitting, 2 Way, Retrofit Patent # 62/239,394 Loos & Co., Inc. - ware Division 2.27
38 SAFR2-1/4 Mount Fastener Mount The SAFR2-1/4 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports in a retrofit enviroment. Existing fastener only needs to be loosened to install the SAFR2. Used for attachment to a steel, concrete, or wood structural member. The 1/4 inch (6 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, and Orange cable and are ideal for 2-way bracing. The SAFR2's maintain the rated break strength of size 3 (Gold), and 4 (Orange) cable without the need of a thimble. The SAFR2's may be used at both ends of the cable for anchoring equipment. SAFR2's are offered in six different mounting sizes,safr2-1/4, SAFR2-3/8, SAFR2-1/2, SAFR2-5/8, SAFR2-3/4, and SAFR2-7/8. Loos & Co., Inc. - ware Division 2.28
39 SAFR2-3/8 Mount Fastener Mount The SAFR2-3/8 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports in a retrofit enviroment. Existing fastener only needs to be loosened to install the SAFR2. Used for attachment to a steel, concrete, or wood structural member. The 3/8 inch (10 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, and Orange cable and are ideal for 2-way bracing. The SAFR2's maintain the rated break strength of size 3 (Gold), and 4 (Orange) cable without the need of a thimble. The SAFR2's may be used at both ends of the cable for anchoring equipment. SAFR2's are offered in six different mounting sizes,safr2-1/4, SAFR2-3/8, SAFR2-1/2, SAFR2-5/8, SAFR2-3/4, and SAFR2-7/8. Loos & Co., Inc. - ware Division 2.29
40 SAFR2-1/2 Mount Fastener Mount The SAFR2-1/2 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports in a retrofit enviroment. Existing fastener only needs to be loosened to install the SAFR2. Used for attachment to a steel, concrete, or wood structural member. The 1/2 inch (13 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, and Orange cable and are ideal for 2-way bracing. The SAFR2's maintain the rated break strength of size 3 (Gold), and 4 (Orange) cable without the need of a thimble. The SAFR2's may be used at both ends of the cable for anchoring equipment. SAFR2's are offered in six different mounting sizes,safr2-1/4, SAFR2-3/8, SAFR2-1/2, SAFR2-5/8, SAFR2-3/4, and SAFR2-7/8. Loos & Co., Inc. - ware Division 2.30
41 SAFR2-5/8 Mount Fastener Mount The SAFR2-5/8 is designed for use in attaching Seismic Bracing to cable trays, HVAC equipment, clevis hangers, sprinkler systems and trapeze supports in a retrofit enviroment. Existing fastener only needs to be loosened to install the SAFR2. Used for attachment to a steel, concrete, or wood structural member. The 5/8 inch (16 mm) fastener mounting hole will accept lag bolts, bolts, threaded rod and concrete anchors in both metric and imperial sizes. The two cable mounts will accept Gold, and Orange cable and are ideal for 2-way bracing. The SAFR2's maintain the rated break strength of size 3 (Gold), and 4 (Orange) cable without the need of a thimble. The SAFR2's may be used at both ends of the cable for anchoring equipment. SAFR2's are offered in six different mounting sizes,safr2-1/4, SAFR2-3/8, SAFR2-1/2, SAFR2-5/8, SAFR2-3/4, and SAFR2-7/8. Loos & Co., Inc. - ware Division 2.31
42 LPF SERIES Low Pry Fitting Patent # 62/311,592 Loos & Co., Inc. - ware Division 2.32
43 LPF-1/4 ESL-1004 ESL-1007 Inspection Hole Exit Fastener Mount Chamfer Slot The LPF 1/4 is specifically designed to reduce the prying effect on fasteners. The cable is nested in the groove provided, and exits through two chamfered slots (to prevent damage to the outer fibers of the cable). An inspection hole is provided to insure that the cable is placed in the correct position within the groove. The LPF has the lowest prying factor yet to be achieved. Loos & Co., Inc. - ware Division 2.33
44 LPF-3/8 ESL-1004 ESL-1007 Inspection Hole Exit Chamfer Fastener Mount Slot The LPF 3/8 is specifically designed to reduce the prying effect on fasteners. The cable is nested in the groove provided, and exits through two chamfered slots (to prevent damage to the outer fibers of the cable). An inspection hole is provided to insure that the cable is placed in the correct position within the groove. The LPF has the lowest prying factor yet to be achieved. Loos & Co., Inc. - ware Division 2.34
45 LPF-1/2 ESL-1004 ESL-1007 Inspection Hole Exit Chamfer Fastener Mount Slot The LPF 1/2 is specifically designed to reduce the prying effect on fasteners. The cable is nested in the groove provided, and exits through two chamfered slots (to prevent damage to the outer fibers of the cable). An inspection hole is provided to insure that the cable is placed in the correct position within the groove. The LPF has the lowest prying factor yet to be achieved. Loos & Co., Inc. - ware Division 2.35
46 LPF-5/8 ESL-1004 ESL-1007 Inspection Hole Exit Chamfer Fastener Mount Slot The LPF 5/8 is specifically designed to reduce the prying effect on fasteners. The cable is nested in the groove provided, and exits through two chamfered slots (to prevent damage to the outer fibers of the cable). An inspection hole is provided to insure that the cable is placed in the correct position within the groove. The LPF has the lowest prying factor yet to be achieved. Loos & Co., Inc. - ware Division 2.36
47 LPF-3/4 ESL-1004 ESL-1007 Inspection Hole Exit Chamfer Fastener Mount Slot The LPF 3/4 is specifically designed to reduce the prying effect on fasteners. The cable is nested in the groove provided, and exits through two chamfered slots (to prevent damage to the outer fibers of the cable). An inspection hole is provided to insure that the cable is placed in the correct position within the groove. The LPF has the lowest prying factor yet to be achieved. Loos & Co., Inc. - ware Division 2.37
48 9P62 Lateral Bracing Installation Instructions ESL-1004 ESL cable dia. min. "tag". 1 1/2 pipe dia. min. Sleeve - See Fig.1 A. Slide Oval Sleeve onto end of cable. Slide sleeve up cable to allow working room. B. Wrap cable around pipe twice. (TIP - Form simple knot on second wrap holds cable in place). C. Slide loose end of cable into sleeve and pull cable to remove slack. D. Crimp sleeve per Figure 1 below. E. Repeat in opposite direction. Figure 1 3.1
49 9P62 Longitudinal Bracing Installation Instructions ESL-1004 ESL-1007 Coupling or Clamp Oval Sleeve 1 cable dia. "tag". A. Slide Oval Sleeve onto end of cable. Slide sleeve up cable to allow working room. B. Wrap cable around pipe twice. (Wrap must be on the far side of a pipe clamp or grooved coupling). C. Slide loose end of cable into sleeve and pull cable to remove slack. D. Crimp sleeve per Figure 1 below. E. Repeat in opposite direction. Figure 1 3.2
50 9P62 4-Way Bracing Installation Instructions ESL-1004 ESL-1007 Sleeve Coupling or Clamp A 4-way brace is the combination of a lateral brace and a longitudinal brace. Follow the below instructions, starting with the lateral brace. 1 cable dia. min. "tag" Lateral Brace A. Slide Oval Sleeve onto end of cable. Slide sleeve up cable to allow working room. B. Wrap cable around pipe twice. (TIP - Form simple knot on second wrap holds cable in place). C. Slide loose end of cable into sleeve and pull cable to remove slack. D. Crimp sleeve per Figure 1 below. E. Repeat in opposite direction. Figure 1 Longitudinal Brace A. Slide Oval Sleeve onto end of cable. Slide sleeve up cable to allow working room. B. Wrap cable around pipe twice. (Wrap must be on the far side of a pipe clamp or grooved coupling). C. Slide loose end of cable into sleeve and pull cable to remove slack. D. Crimp sleeve per Figure 1 below. E. Repeat in opposite direction. 3.3
51 Through Bolt Sizes 1/2, 5/8, 3/4. (See NFPA-13 Figure ) LPF Wood Deck Loop Oval Sleeve SAF Wood Deck Through Bolt Sizes 1/2, 5/8, 3/4. (See NFPA-13 Figure ) Stake Eye Through Bolt Sizes 1/2, 5/8, 3/4. (See NFPA-13 Figure ) Wood Deck Load Perpendicular to Structural Member Through Bolts in Wood Above listed values based on wood with a specific gravity of Values for other woods can be obtained by multiplying above values by factors listed in figure1. 3.4
52 Lag Bolt Sizes 3/8, 1/2, 5/8. (See NFPA-13 Figure ) LPF Wood Deck Oval Sleeve Loop SAF Lag Bolt Sizes 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Wood Deck Stake Eye Lag Bolt Sizes 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Wood Deck Load Perpendicular to Structural Member Lag Bolts in Wood Above listed values based on wood with a specific gravity of Values for other woods can be obtained by multiplying above values by factors listed in figure1. 3.5
53 LPF Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Oval Sleeve Loop SAF Clip Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Stake Eye Anchor Sizes Concrete Deck 1/4, 3/8, 1/2 (See NFPA-13 Figure (a)) Load Perpendicular to Structural Member Wedge Anchors in 3000 psi Lightweight Cracked Concrete (207 bar) on Metal Decking 3.6
54 LPF Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Oval Sleeve Loop SAF Clip Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Stake Eye Anchor Sizes Concrete Deck 1/4, 3/8, 1/2 (See NFPA-13 Figure (a)) Load Perpendicular to Structural Member Wedge Anchors in 3000 psi Nornal Weight Cracked Concrete 3.7
55 LPF Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Oval Sleeve Loop SAF Clip Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Stake Eye Anchor Sizes Concrete Deck 1/4, 3/8, 1/2 (See NFPA-13 Figure (a)) Load Perpendicular to Structural Member Undercut Anchors in 3000 psi Nornal Weight Cracked Concrete 3.8
56 LPF Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Oval Sleeve Loop SAF Clip Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Stake Eye Anchor Sizes Concrete Deck 1/4, 3/8, 1/2 (See NFPA-13 Figure (a)) Load Perpendicular to Structural Member Wedge Anchors in 3000 psi Lightweight Cracked Concrete 3.9
57 LPF Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Oval Sleeve Loop SAF Clip Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Stake Eye Anchor Sizes Concrete Deck 1/4, 3/8, 1/2 (See NFPA-13 Figure (a)) Load Perpendicular to Structural Member Wedge Anchors in 4000 psi Nornal Weight Cracked Concrete 3.10
58 LPF Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Oval Sleeve Loop SAF Clip Anchor Sizes 3/8, 1/2, and 5/8 (See NFPA-13 Figure (a)) Concrete Deck Stake Eye Anchor Sizes Concrete Deck 1/4, 3/8, 1/2 (See NFPA-13 Figure (a)) Load Perpendicular to Structural Member Wedge Anchors in 6000 psi Nornal Weight Cracked Concrete 3.11
59 Steel Member Stake Eye SAF Loop LPF Bolt Sizes 1/4, 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Bolt Sizes 1/4, 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Steel Member Oval Sleeve Load Perpendicular to Structural Member Connections to Steel 3.12
60 1/2 Beam Depth but not <3 in. Wood Beam Wood Beam Wood Beam LPF Bolt Sizes 1/2, 5/8, 3/4 (See NFPA-13 Figure ) SAF Bolt Sizes 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Loop Bolt Sizes 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Stake Eye 1/2 Beam Depth but not <3 in. Oval Sleeve 1/2 Beam Depth but not <3 in. 1/2 Beam Depth but not <3 in. Load Perpendicular to Structural Member Through Bolts in Wood Above listed values based on wood with a specific gravity of Values for other woods can be obtained by multiplying above values by factors listed in figure
61 Wood Beam Wood Beam Wood Beam LPF Lag Bolt Sizes 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Lag Bolt Sizes 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Loop SAF Lag Bolt Sizes 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Stake Eye 1/2 Beam Depth but not <3 in. Oval Sleeve 1/2 Beam Depth but not <3 in. 1/2 Beam Depth but not <3 in. Load Perpendicular to Structural Member Lag Bolts in Wood Above listed values based on wood with a specific gravity of Values for other woods can be obtained by multiplying above values by factors listed in figure
62 Concrete Beam Concrete Beam LPF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Sleeve Loop SAF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Concrete Beam Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Stake Eye 1/2 Beam Depth but not <3 in. Load Perpendicular to Structural Member Wedge Anchors in 3000 psi Normal Weight Cracked Concrete 3.15
63 Concrete Beam Concrete Beam LPF Anchor Sizes 3/8, 1/2, 5/8 (See NFPA-13 Figure ) SAF Anchor Sizes 3/8, 1/2, 5/8 (See NFPA-13 Figure ) Loop Sleeve Concrete Beam Anchor Sizes 3/8, 1/2, 5/8 (See NFPA-13 Figure ) Stake Eye Load Perpendicular to Structural Member Undercut Anchors in 3000 psi Normal Weight Cracked Concrete 3.16
64 Concrete Beam Concrete Beam LPF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) SAF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Loop Sleeve Concrete Beam Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Stake Eye Load Perpendicular to Structural Member Wedge Anchors in 3000 psi Lightweight Cracked Concrete 3.17
65 Concrete Beam Concrete Beam LPF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) SAF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Loop Sleeve Concrete Beam Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Stake Eye Load Perpendicular to Structural Member Wedge Anchors in 4000 psi Normal Weight Cracked Concrete 3.18
66 Concrete Beam Concrete Beam LPF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) SAF Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Loop Sleeve Concrete Beam Anchor Sizes 3/8, 1/2, 5/8, 3/4 (See NFPA-13 Figure ) Stake Eye Load Perpendicular to Structural Member Wedge Anchors in 6000 psi Normal Weight Cracked Concrete 3.19
67 Steel Beam LPF Steel Beam Bolt Sizes 1/4, 3/8, Bolt Sizes 1/4, 3/8, 1/2, 5/8. 1/2, 5/8. (See NFPA-13 (See NFPA-13 Figure ) Figure ) Oval Sleeve Stake Eye Steel Beam SAF Bolt Sizes 1/4, 3/8, 1/2, 5/8. (See NFPA-13 Figure ) Loop Oval Sleeve Load Perpendicular to Structural Member Connections to Steel 3.20
68 Wood Beam Fastener (See NFPA-13 Figure ) Straight Stake Eye Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. Oval Sleeve LPF Wood Beam Fastener (See NFPA-13 Figure ) Straight Stake Eye Oval Sleeve Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. LPF Load Parallel to Structural Member Through Bolts in Wood Above listed values based on wood with a specific gravity of Values for other woods can be obtained by multiplying above values by factors listed in figure
69 Wood Beam Fastener (See NFPA-13 Figure ) Straight Stake Eye Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. Oval Sleeve LPF Wood Beam Fastener (See NFPA-13 Figure ) Straight Stake Eye Oval Sleeve Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. LPF Load Parallel to Structural Member Lag Bolts in Wood Above listed values based on wood with a specific gravity of Values for other woods can be obtained by multiplying above values by factors listed in figure
70 Concrete Beam Fastener (See NFPA-13 Figure ) SAF Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. LPF Oval Sleeve Concrete Beam Fastener (See NFPA-13 Figure ) Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. Straight Stake Eye Oval Sleeve LPF Load Parallel to Structural Member Wedge Anchors in 3000 psi Normal Weight Cracked Concrete 3.23
71 Concrete Beam Fastener (See NFPA-13 Figure ) SAF Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. LPF Oval Sleeve Concrete Beam Fastener (See NFPA-13 Figure ) Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. Straight Stake Eye Oval Sleeve LPF Load Parallel to Structural Member Undercut Anchors in 3000 psi Normal Weight Concrete 3.24
72 Concrete Beam Fastener (See NFPA-13 Figure ) SAF Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. LPF Oval Sleeve Concrete Beam Fastener (See NFPA-13 Figure ) Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. Straight Stake Eye Oval Sleeve LPF Load Parallel to Structural Member Wedge Anchors in 3000 psi Lightweight Cracked Concrete 3.25
73 Concrete Beam Fastener (See NFPA-13 Figure ) SAF Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. LPF Oval Sleeve Concrete Beam Fastener (See NFPA-13 Figure ) Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. Straight Stake Eye Oval Sleeve LPF Load Parallel to Structural Member Wedge Anchors in 4000 psi Normal Weight Cracked Concrete 3.26
74 Concrete Beam Fastener (See NFPA-13 Figure ) SAF Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. LPF Oval Sleeve Concrete Beam Fastener (See NFPA-13 Figure ) Min. four fastener diameters but not <1/3 beam depth and not <3 in. for wood beams. Straight Stake Eye Oval Sleeve LPF Load Parallel to Structural Member Wedge Anchors in 6000 psi Normal Weight Cracked Concrete 3.27
CABLE & WIRE MILBAR SAFETY WIRE PRODUCTS
MILBAR SAFETY WIRE PRODUCTS 1 - REVERSIBLE SAFETY WIRE TWISTER WITH WIRE CATCHER Milbar s new safety wire twister pliers (formally the TigerWave) offer the best of all worlds! Now you can twist safety
More informationOpen Up Your View With CABLE SYSTEMS
Open Up Your View With CABLE SYSTEMS PRESENTED BY CROWN HERITAGE Our Cable Multiple options to accomodate any deck or stair design Marine Grade 316 stainless steel Swaging is the term used for attaching
More informationCable & Bolt Cutters. F o r P. r o f e. s s i o. n a l s. .. S i. n c e 1
F o r P Cable & Bolt Cutters r o f e s s i o n a l s. Klein meets and exceeds the highest of standards to create great cable and bolt cutters. Offering greater cutting power, clean and precise cuts, and
More informationSolarMount (E)volution
SolarMount (E)volution SOLARMOUNT (E)VOLUTION: THE BEST JUST GOT BETTER. Engineering, Excellence, and Ease. Performance Engineered for versatility and reduced installation time, SolarMount (E)volution
More informationWESTERN WIRE PRODUCTS
WESTERN WIRE PRODUCTS Celebra ng 100 years of Quality and Service 1914 2014 Thanks to our dedicated employees and customers we are celebra ng 100 years of being in business and we look forward to servicing
More informationBSR A300 Part 3 Draft 1 Version 1, a
Standards & Regulations Cabling and Bracing Standard Proposed Revision This is an excerpt from the draft version of the ANSI standard for supplemental support systems cabling and bracing used in tree care
More informationCable Cutter Square. 25 Tape Measure. Chalk Line Level Loctite 242 Blue
ATLANTIS RAIL Contact Information: Atlantis Rail Systems 70 Armstrong Road 3900 Civic Center Drive Plymouth, MA 02360 North Las Vegas, NV 89030 (800) 541-6829 or (508) 732-9191 (508) 732-9798 www.atlantisrail.com
More informationDown Stage Right -Theatrical and Entertainment Rigging Supplies
Shackle Plates There are five uniquely different designs in the Shackle Plates Dynasty. Each one allows you the freedom of choice as you design the rigging requirements of your scenery, as well as meeting
More informationSECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of
More informationIndex Pipe Hangers and Straps
Index Pipe Hangers and Straps Fig. 1 Standard Clevis Hanger MSS-SP-69, Type 1 WW-H-171E, Type 1 Page 14 Fig. 1CI Clevis Hanger for A.W.W.A. Page 16 Fig. 81 Clevis Hanger WW-H-171E, Type 12 Page 70 Fig.
More informationCable Railing Kit Application Guide
Cable Railing Kit Application Guide January 2019 Nationwide Industries 10333 Windhorst Rd. Tampa, FL 33619 813.988.2628 Fax: 813.988.3465 Photo courtesy of FabWorx Framework You Will Need for Cable Railing
More informationATI Evaluation Service A Division of Architectural Testing Certification Services
ATI Evaluation Service A Division of Architectural Testing Certification Services Subject to Renewal: 10/13/2016 Issued: 12/17/2014 Visit www.ati-es.com for current status Revised: 06/05/2015 Page 1 of
More informationSeamers, Folding Tools & Brake
Hand Seamers with Die-Cast Zinc Jaws S5 Compact 5 (127 mm) Jaws with Big 2 (51 mm) Bending Depth Hand Seamers with Forged Steel Jaws Seamers, Folding Tools Not for use with steel S9 Big 9 (229 mm) Jaws
More informationModular XP Ramp Assembly Manual
Modular XP Manual 1 Contents Overview... 2-5 1.1 Tools required...6 1.2 Hardware list...6 Ramp & Platform Standard Parts 2.1 Ramp Parts...7 2.2 Platform Parts...8 2.3 Standard Platform Configurations...
More informationArchitectural Cable Railing Products
Architectural Cable Railing Products August 1, 2017 ISO Certified U.S.A. Manufacturer www.ultra-tec.com TABLE OF CONTENTS ULTRA-TEC RAILING PRODUCTS Cable Type and Size... 3 Options for How to Receive
More informationMETALWORKS Wings Accent and Acoustical Clouds Installation Instructions
CEILING SYSTEMS Between us, ideas become reality METALWORKS Wings Accent and Acoustical Clouds Installation Instructions 1. GENERAL 1.1. Product Description MetalWorks Wings is a decorative ceiling element
More informationMetal Bending Tools, Scribes & Awls
Metal Bending Tools, Scribes & Awls Hand Seamers Die-Cast Zinc Jaws Not for use with steel Die-Cast Zinc Jaws Not for use with steel malco tool book better ideas for the real world. S5R Compact 5 in. (127
More informationCMA-455 Suspended Ceiling-Tile Reinforcing Kit
INSTALLATION INSTRUCTIONS CMA-455 Suspended Ceiling-Tile Reinforcing Kit The provides a sturdy support for LCD/DLP hanging brackets (and certain other products) when installing these products in a suspended
More informationSTRENGTH Aligned teeth provide superior gripping power over standard vertical teeth. STRENGTH Diamond serrated jaws provide a firm grip
STRENGTH Aligned teeth provide superior gripping power over standard vertical teeth STRENGTH Diamond serrated jaws provide a firm grip PLIERS AND SNIPS Locking Pliers Slip Joint Pliers Electrician s Pliers
More informationHang-TITE Rod Hanger Screws
Description The Hang-TITE Rod Hanger Screw is a one-piece, internally threaded anchor designed for suspending threaded rod for applications like cable-tray, pipe hanging, fire protection, and electrical
More informationINFUSIONS and METALWORKS Wings Accent and Acoustical Clouds
INFUSIONS and METALWORKS Wings Accent and Acoustical Clouds Assembly and Installation Instructions 1. GENERAL 1.1 Product Description Wings is a decorative ceiling element consisting of a 10 foot long
More informationSWAY BRACE PIPE ATTACHMENT FIG. 010
Function: Designed for bracing pipe against sway and seismic disturbance. The pipe attachment component of a sway brace system used in conjunction with a PHD Manufacturing structural attachment fitting,
More informationATLANTIS RAIL HandiSwage Installation Instructions ATLANTIS RAIL Contact Information Atlantis Rail Systems November, 2013
ATLANTIS RAIL HandiSwage Installation Instructions ATLANTIS RAIL Contact Information Atlantis Rail Systems November, 2013 Atlantis Rail s HandiSwage System is an easy to use cable railing product utilizing
More informationMake your railing view friendly with the original stainless steel cable infill for wood, metal, and composite-sleeved wood railing.
Make your railing view friendly with the original stainless steel cable infill for wood, metal, and composite-sleeved wood railing. 1 Feeney makes it easy The CableRail cable infill system is slender,
More informationThe Festival Assembly Instructions
The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New
More informationThe DeltaGrip System. Safety and Operating Instructions. Trigger. Air Supply Connection. Handle Assembly. Air Line Assembly.
The DeltaGrip System Safety and Operating Instructions Trigger Air Supply Connection Handle Assembly Air Line Assembly Punch Die Pneumatic Diaphragm Assembly Shackle, Pin & Jam Nut Jaw Frame Shoulder Screw
More informationPrecision Engineering & Reliability
Precision Engineering & Reliability WIRE ROPE SUSPENSION SYSTEM What is the DobyGrip? The modern way to suspend static loads - quickly It is widely accepted that labour costs are a significant outlay on
More informationLEG CURL IP-S1315 INSTALLATION INSTRUCTIONS
LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written
More informationCEILING-MOUNTED MONORAIL ANCHOR TRACK SYSTEM Assembly and Operation Instruction Manual
CEILING-MOUNTED MONORAIL ANCHOR TRACK SYSTEM Assembly and Operation Instruction Manual This manual is for various mounting types and plain and trussed track profiles. ISO 9001:2008 Registered Manual 103-0075
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Stair Panels with Simplified Stair Bracket SSB-05 and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and
More informationTel / (USA & CANADA) /
Tel.58.847 / 8.388.459 (USA & CANADA) / Email sales@msdiscounttool.com MULTIPURPOSE CLAMPS - USA SERIES 7: Lightweight and 4% stronger than C clamps. Floating jaws that always stay parallel. Designed to
More informationSection Member. H (in.) WT. lb./ft. Pull Out Strength Slip Resistance Torque Size / Thread All Series
Design Data Channel TABLE 1 Elements of Sections Properties for Design Single Channels Nominal Thickness (inches) ga = 0.105 ga = 0.075 16 ga = 0.060 Double Channels LEGEND I Moment of inertia S Section
More informationCreate cable assemblies to fit your style
2015 Feeney (11/15) Quick-Connect Brochure #2015-975B Create cable assemblies to fit your style Quick-Connect Solutions Guide The fast and easy way to create your own CableRail assemblies! Our CableRail
More informationBest MATERIALS.com Discount Warehouse
Best MATERIALS.com Discount Warehouse Metal Bending Tools, Scribes & Awls 35 malco tool book better ideas for the real world. Hand Seamers Die-Cast Zinc Jaws Not for use with steel Die-Cast Zinc Jaws Not
More informationElco Construction Products 1301 Kerr Drive Decorah, IA fax:
Technical Manual 2010 HangerMate anchors were designed to speed installation of fire sprinkler, HVAC, refrigeration, general piping, and electrical systems. They can also be used to install strut channels,
More informationProduct #: Product #:
STANLEY FATMAX Push-Lock Groove Joint Pliers Multi-purpose jaws designed to grasp flat and round objects. Push-Lock technology allows for quick and easy adjustment in 17 positions. Induction hardened jaws
More informationFABA. Installation Instructions. Conductor Bar System. Publication #FABA-03 3/1/04 Part Number: Copyright 2004 Electromotive Systems
FABA Conductor Bar System Installation Instructions Publication #FABA-03 3/1/04 Part Number: 005-1062 Copyright 2004 Electromotive Systems 1S 100 Z Installation Instructions Contents: Basic Diagram - -
More informationOriginally Issued: 09/26/2012 Revised: 10/15/2018 Valid Through: 09/30/2019
SUNMODO CORPORATION 14800 NE 65 th Street Vancouver, WA 98682 SUNMODO EZ ROOF MOUNT L-FOOT KITS FOR SHINGLE ROOFS CSI Section: 06 25 23 Wood, Plastic, and Composite Fastenings 07 71 00-Roof Specialties
More informationMulti-Set II Drop-In Anchors
CONCRETE ANCHORING SPECIALISTS Internally Threaded Heavy- Duty Anchoring Systems DESCRIPTION/SUGGESTED SPECIFICATIONS Drop-In, Shell-Type Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE Drop-In, shell-type
More informationSTAR TOOL SUPPLY / GRAND TOOL SUPPLY
MULTIPURPOSE CLAMPS - USA SERIES 7: Lightweight and 4% stronger than C clamps. Floating jaws that always stay parallel. Designed to eliminate distorting or twisting action. Cantilever action provides 4:
More informationInstallation Instructions for OPGW Bolted Dead End
INS-ACA015 OPGW Bolted Dead End Procedure 1. Disassemble dead end. Remove one bolt from the same side of each keeper. Loosen other bolts to permit conductor to be placed in the conductor groove. If keepers
More informationAvailable in high-capacity. and assembled by hand for smooth operation. Durable chrome-plated finish. Heat-treated for long life.
Klein s line of wrenches are forged from the finest steel and are designed to deliver great strength and long working life. Regardless of the job type, Klein has a wrench that will help the professional
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationUmbrella Inserts and Stubby Screens
ADHESIVE ANCHORING SPECIALISTS Umbrella Inserts and Stubby Screens High Performance Adhesive Systems for Fastening to Hollow Base Materials DESCRIPTION/ADVANTAGES Hollow Block Fastening with A7 Adhesive
More informationDekPro Prestige Aluminum Rail System Level Railing Installation Instructions
ing Installation Guide Please read all instructions completely before starting any installation of DekPro Prestige Railing Systems. SAFETY: Always be safe and follow all instructions when using power tools
More informationReplacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981
Page 1 of 12 Date: December 2, 1981 Subject: Models: Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System F-28C and 280C Effectivity: Helicopters manufactured prior to
More information1. Layout. Step 1. Step 2. Step 3. Fig. 1
1-3/8 Panel Clamp Tools You Will Need: Tape Measure, Mason s String, Stakes, Hole Digger, Shovel, Level, Wheelbarrow, Wrenches or Adjustable Wrench, Hacksaw, Pliers, Cutting Pliers, Fence Stretcher and
More informationWrenches. Wrenches. F o r P. r o f e. s s i o. n a l s. .. S i. n c e 1
F o r P r o f e Klein s line of wrenches are forged from the finest steel and are designed to deliver great strength, and long working life. Regardless of the job type, Klein has a wrench that will help
More informationArchitectural Door Accessories. Markar Continuous Hinges
Architectural Door Accessories Why Continuous Hinges? Hinge failure most commonly begins when doors are opened beyond stop device limits. The resulting kickback shock to the hinges can surpass 1000 lbs.
More informationTS-20KD-1010 LOW PROFILE CARGO SCALE INSTALLATION GUIDE
TS-20KD-1010 LOW PROFILE CARGO SCALE INSTALLATION GUIDE Triner Scale & Mfg. Co., Inc. 8411 Hacks Cross Rd. Olive Branch, MS 38654 Phone: 800-238-0152 Fax: 662-809-2386 Description The Triner Scale Model
More informationTransform Cable Rail MUST be installed on 4" x 4" wooden posts sleeved with Transform post sleeves to support cable tension!
CABLE RAIL INSTALLATION INSTRUCTIONS OVERVIEW...2 LEVEL...3 STAIR...13 Transform Cable Rail MUST be installed on 4" x 4" wooden posts sleeved with Transform post sleeves to support cable tension! 1 Need
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationHOUSE PARTS PACKED IN HOUSE BOX PARTS IN PLASTIC BAG (HARDWARE) PARTS IN SMALL PLASTIC BAG (FLOOR CLIPS) PARTS PACKED IN BUNDLE
Check parts against this list before starting assembly. Refer to illustrations on pages 6 and 7 to view house parts. If any shortages are found, refer to Packing Slip for claim instructions. Item 3 5 6
More informationIX. FLARED JOINTS IX. FLARED JOINTS
IX. FLARED JOINTS IX. FLARED JOINTS While copper tube is usually joined by soldering or brazing, there are times when a mechanical joint may be required or preferred. Flared fittings (Figures 28 and 29)
More informationStargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe
Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe INFORMATION The Stargrip Mechanical Joint Restraint System is a unique product with a proven design that provides an exceptional
More informationANCHORS SLEEVE ANCHORS BOLT DIAMETER
SLEEVE ANCHORS No hole spotting. No mis-alignments. Simply drill through the fixture into concrete, insert and tighten. Preassembled for fast, easy installation. No special tools necessary; meets federal
More informationPREPARATION & TOOL CHECK LIST
INSTRUCTION MANUAL RAILING PRODUCTS BEGIN TO AGE AS SOON AS THEY ARE EXPOSED TO NATURE. BUILDINGS EXPERIENCE AGING FACTORS DIFFERENTLY, SO IT IS DIFFICULT TO PREDICT HOW LONG RAILING PRODUCTS WILL LAST.
More informationClampStar Safe-T-Link Tether Installation Instructions for Deadends
Tel.800-269-1462 Fax.800-311-9857 P.O. Box 100279, Birmingham, AL 35210 www.classicconnectors.com Classic Connectors, Inc. ClampStar Safe-T-Link Tether Installation Instructions for Deadends General Safety
More informationFramework for Cable Railing
Framework for Cable Railing End Post Construction Since hundreds of pounds of tension are being applied to end posts using cable railing, those posts must be substantial enough to handle that tension.
More informationDobyGrip Accessories. Wire with Loop. Wire with Closed M6 & *M8 Eye Bolt. Wire with Carabina
Wire with Loop Quick and easy fixing to purlins, beams etc by forming a choke knot. Reduces the installation time compared to conventional methods of suspension. All wires are supplied including the DobyGrip
More informationMax. Rec. Load. Wt. Per Inch lbs. kn lbs. kn lbs. kg. Wt. Per Inch lbs. kn lbs. kn lbs. kg 750 F (399 C)
FIG. 10 FIG. 15 & 15L Function: Designed for use in pipe hanger assemblies. (Type 304 or 316 Stainless Steel upon request) Ordering: Specify figure number, rod size, length (), material, and finish. 650
More informationAUXILIARY FRAMING AND ACCESSORIES
CUSTOM CABINETS & RACKS STRUT AND ACCESSO- RIES JUNCTION KITS ANGLE AND BRACE KITS SPLICE KITS BRACE KITS INSTALLATION KITS WALL ANGLE KITS RUBBER END CAPS SUPPORT INSTALLATION AND SUPPORT KITS STANCHION
More informationPeco Fasteners 3/8 Internal Plug Drop In 50 Per Jar 3/8-16 SMART DROP IN ANCHOR ZINC
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-794 Fax: 936-560-4685 Catalog Number Manufacturer Description Weight per unit Product Category 6337J 3/8-6 Smart Drop In Zinc Peco Fasteners,
More informationClearSpan PolyMax Windbreak Wall
ClearSpan PolyMax Windbreak Wall Photo may show a different but similar model. 2007 ClearSpan All Rights Reserved. Reproduction is prohibited without permission. Revision date: February 2007ldg STK# DIMENSIONS
More informationModular XP Ramp Assembly Manual
Modular XP Manual 1 Contents Overview... 2-5 Section 1: 1.1 Tools required...6 1.2 Hardware list...6 Ramp & Platform Standard Parts 2.1 Ramp Parts...7 2.2 Platform Parts...8 2.3 Standard Platform Configurations...
More informationParts list continues on Page 2 HOUSE PARTS PACKED IN HOUSE BOX PARTS IN SMALL PLASTIC BAG (HARDWARE) POST PARTS PACKED IN THIS BOX (LARGE PLASTIC BAG)
Form 05-07 Instructions and Parts List MSS- Martin Safety System NOTES: () A complete system is packed in two boxes post box and house box. House box contains hardware for both post and house assembly.
More informationJoiners and tensioners
Joiners and tensioners Farm and Livestock Line www.maxtensor.com MAXTENSOR is ideal for: Farms Vineyards trellising Fruit trees trellising Vegetables Greenhouses Gardening Livestock Fencing Electric fencing
More informationCertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS. Fence Installation Guide 3', 4' & 6' High
CertainTeed INSTALLATION GUIDE SIMTEK FENCE PRODUCTS Fence Installation Guide 3', 4' & 6' High INSTALLATION GUIDE These instructions are designed to assist both professional installers and do-it-yourselfers
More informationDesigning a Wood Railing
Inside: Construction, location of end posts Configuration of corners Location of intermediate posts Choosing the right cable diameter Spacing of cables Cutting cables in field versus factory-cut Hardware
More informationLarge Diameter Tapcon
CONCRETE ANCHORING SPECIALISTS Large Diameter Tapcon (LDT ) Anchors Finished head, Removable Anchor DESCRIPTION/SUGGESTED SPECIFICATIONS Self-threading Anchors SPECIFIED FOR ANCHORAGE INTO CONCRETE The
More informationOne Piece LSD/Vector Pads from TIE DOWN ENGINEERING Easier installation with 70% fewer parts Lower cost with competitive pricing
NEW! One Piece SD/ector Pads from TIE DOWN ENGINEERING Easier installation with 70% fewer parts ower cost with competitive pricing Do the Math! Compare material and labor cost with the New SD and ector
More informationFace Mount to Through-the-Post Mount
Face Mount to Through-the- Mount Cable Runs through Two Corners When going around two corners, it s necessary to tension the cable from both ends as shown in Deck 4. Use the 672 series The tensioning devices
More informationRAILING. Installation Guide
RAILING Installation Guide THE BEST CHOICE FOR STRONG & DURABLE RAILING SYSTEMS Our exclusive manufacturing process ensures our vinyl railing will provide superior strength plus it is virtually maintenance
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all
More informationTechnologies, Inc. Installation Instructions for Anchors & Components. Rev PAGE 1 / 11
Installation Instructions for Anchors & Components PAGE 1 / 11 GROUND ANCHOR INSTALLATION INSTRUCTIONS NOTE: 1) The tensioning bolt can be inserted in the head from either side. 2) In areas of severe cold
More informationCutting Tools HC-20. Handheld Hydraulic Cutter. Operator s Manual
Locoloc Cutting Tools HC-20 Handheld Hydraulic Cutter Operator s Manual CONTENT Title Page Specifications 1 General Information Guide 2 Troubleshooting Guide 5 Operating Instructions 7 Parts Diagram 8
More informationNX7 SERIES 5-1/2 HANDRAIL
STORAGE & HANDLING The handrails are shipped unassembled. Upon receipt, immediately check all material for any damage that may have occurred in transit and verify that all of the items and quantities are
More informationSWAGGED VS. DIE CAST CABLE COMPONENTS. Enclosing Wire Ends With Swaged and Die Cast Cable Components
Enclosing Wire Ends With Swaged and Die Cast Cable Components Swagged Cable Terminations Die Cast Cable Terminations Via Mechanical Deformation Swaged fittings are machined using alloy steels and other
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationPrecision Engineering & Reliability WIRE ROPE SUSPENSION SYSTEM
Precision Engineering & Reliability WIRE ROPE SUSPENSION SYSTEM DobyGrip Wire with Loop Quick and easy fixing to purlins, beams etc by forming a choke knot. Reduces the installation time compared to conventional
More informationXL MAX. Suspension System Data Center Ceiling Solutions. Assembly and Installation Instructions
PRELUDE Top Lock XL MAX (4) #8 x 1/" Long Main Beam Sharp Point Truss Head Screws Suspension System Data Center Ceiling Solutions Assembly and Installation Instructions SYSTEM OVERVIEW The Prelude XL Max
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for FortressCable H-Series Cable Panel System With UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain
More informationUmbrella Inserts and Stubby Screens
ADHESIVE ANCHORING SPECIALISTS Umbrella Inserts and High Performance Adhesive Systems for Fastening to Hollow Base Materials DESCRIPTION/ADVANTAGES Hollow Block Fastening with A7+ Adhesive Umbrella Inserts
More informationPIPE/CONDUIT SUPPORTS
PIPE/CONDUIT SUPPORTS Pipe/Conduit Clamps...102-105 Unicushion... 106 Pipe & Tubing (Cush-A-Clamp ) Clamps...107-110 Pipe Hangers... 111 Pipe Rollers...111-112 Pipe Brackets... 113 Reference Tables...114-120
More information6a. Eight Steps to Chain-Link Fence Installation
6a. Eight Steps to Chain-Link Fence Installation Before You Start You will need the following tools to install your chain-link fence: Post hole digger Wheelbarrow, shovel and hoe for mixing concrete Tape
More informationProject: # Solano Community College District
ADDENDUM #02 Project: #16 007 Solano Community College District Horticulture Site Improvements Date: April 26, 2016 The following clarifications are provided based on questions received or changes in District
More informationNON-PENETRATING ROOFTOP HANGERS AND SUPPORTS
SECTION 15062 NON-PENETRATING ROOFTOP HANGERS AND SUPPORTS For best results, display hidden notes to specifier. PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe supports. B. Conduit supports. C. Duct supports,
More informationCABLE RUNWAY & TRAY PRODUCTS
CABLE RUNWAY & TRAY PRODUCTS Cable Runway Products Page 3-3 Adjustable Cable Runway Page 3-4 Cable Runway Junction Products Page 3-13 Cable Runway Mounting Products Page 3-17 Cable Runway Support Products
More informationLeveling Foot RB210. Leg Extender RLT66
Landing for Right & Left Turn R342 ITEMS # 0254049, 0254061, 0254072, 0254076, 0016567, 0254099, 0254110, 0054116, 0254117, 0254126, 0254140, 0254150, 0254156 CUSTOM ACCESS RAMP SYSTEM MODELS # R100, R242,
More informationCrimping and Cutting Tool for Connectors, Accommodates wire. From No. 10 to 22 Awg CRIMPING/CUTTING TOOL FOR CONNECTORS. from No.
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 1005 Crimping/Cutting Tool For Connectors Klein Tools Catalog Number 1005 Manufacturer Klein Tools Description Crimping
More informationGrowSpan Series 500 Roll-Up Ends
GrowSpan Series 500 Roll-Up Ends Photo may show a different but similar model. Doorframe materials are not included. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission.
More informationFlex Fence Instruction Manual
The Safer Stronger Smarter Choice Flex Fence Instruction Manual Table of contents 2 3 4 4 5 5 6 7 8 10 10 11 11 12 13 13 15 18 18 19 20 22 Table of contents Supplies, tools and equipment Introduction Laying
More informationCable Hanging Instruction Manual
Tri-States Grain Conditioning, Inc. Cable Hanging Instruction Manual There are several types of grain storage tanks and bins. Parts of these instructions may be modified to fit the circumstances. Care
More informationHandle Length (in.) Ultimate Load (lbs.) Weight Each (lbs.)
L-150 Lever Type Binder Lebus Binders Extra heavy construction at leverage point to prevent spreading. Heel of binder toggles away from load, permitting easy release. Ball and socket swivel joints at hook
More informationPull-down clamps. No Low height clamping jaws, model Bulle
Pull-down clamps The wedge action of clamping jaws is the characteristic feature of these pull down clamps. It causes the pull down effect, which presses the workpiece against both, stop and machine table.
More information