One Piece LSD/Vector Pads from TIE DOWN ENGINEERING Easier installation with 70% fewer parts Lower cost with competitive pricing
|
|
- Noel Hood
- 5 years ago
- Views:
Transcription
1 NEW! One Piece SD/ector Pads from TIE DOWN ENGINEERING Easier installation with 70% fewer parts ower cost with competitive pricing Do the Math! Compare material and labor cost with the New SD and ector ateral System Combination. Never a 5 Ft. Perimeter Anchor No Stabilizer Plates No Frame Ties or Beam Clamps No ongitudinal Anchors Revised Instructions Fewer Systems Required! Exceeds Wind Zone III HUD Code wind load requirements by more than 50% ,193
2 Florida Set-Up Instructions for the ector Dynamics Foundation System 1. SET ECTOR FOUNDATION PADS Clear all loose vegetation from the immediate area where the ector foundation pads will rest. Place a long U-bolt on the ector pads as shown. Press or hammer pads into the ground. ector pads are placed parallel and centered under I-beam. Tip: Place a 3/8" nut on each U-bolt to keep it in place while you position the ector pads. SD/ector Combination Shown TIP: After centering 1st block(s) over ector pads, place wood cap on top of first block and use hydraulic jack between pad and I-beam to force pads into the ground. Higher pier sets may require extra block prior to using hydraulic jack. ong U-bolt 1 2 Position 1st block(s) on pad as shown. 2. SET BOCKS (OR PIERS) ON ECTOR FOUNDATION PADS Center the foundation blocks over the ector pads. 3. INSIDE CONNECTIONS Insert 1/2" carriage bolt into square hole on top flange of the PC adaptor. Place the swivel connector bracket that is attached to one end of the 1-1/4" galvanized strap and thread 1/2" hex nut onto carriage bolt (finger tight). Insert 4" PC schedule 40 pipe into PC pipe adaptor and insert over inside long U-bolt (through slotted holes). Attach 3/8" hex nuts to u-bolt and finger tighten. Repeat the procedure to opposite side of PC pipe. 4. TIGHTEN INSIDE HARDWARE Tighten all previously finger tightened hex nuts (1/2" carriage bolts & 3/8" inside U-bolts). 5. OUTSIDE TENSION BRACKETS Attach an outside tension bracket on the outside of the foundation blocks and ector pads. As shown right. 6. TENSIONING - ECTOR STRAPS Pull strap past slotted bolt. Cut strap inches past bolt, insert the strap into the slotted bolt until flush with opposite side of bolt. Wind strap a minimum of five (5) complete revolutions around the bolt. Continue tightening the slotted tension bolt until all slack has been removed and the galvanized strap is tight ,193
3 ateral Stabilization for Concrete, Slabs & Runners for Single & Double Block Piers Tie Down Marked & Certified G120 Strap w/swivel Connector Part # ength ' ' ' Picture shows single and double block for illustration purposes only Concrete ector System Part # (for single stack blocks) Slotted Bolt Part # To add longitudinal stabilization to single or double stack blocks: 1 P/N ongitudinal Hardware Kit for or Struts for ongitudinal Systems Parts required for the Single Block ector System: 1 P/N Concrete ector System (for single block piers) 2 P/N Slotted Bolts 2 Swivel Strap Connectors ongitudinal Stabilization Hardware Kit for Concrete Part # Concrete ector System Part # (for double stack blocks) Parts required for the Double Block ector System: 1 P/N ector ateral System for Concrete (double block stack) 2 Strap w/ Swivel Connector 2 P/N Slotted Bolt Struts for ongitudinal Systems Part No. Strut ength Pier Height up to 2 Blocks up to 3 Blocks up to 4 Blocks up to 5 Blocks up to 6 Blocks ,240
4 Combine TIE DOWN's ongitudinal ( 2 SD) and ector Systems and SAE! Home 2SD* ector SD/ector ector Stabilizer Frame Beam ongitudinal ength Systems Systems Pads Straps Plates Ties Clamps Anchors in Ft. #59026 #59024 # ' - 32' 2* ' - 48' 2* ' - 64' 2* ' - 76' 2* ' - 90' 2* * Strut lengths are purchased separately (2 per system) Example of a 72 Ft. Single Section Home 8 ft. Side Wall Up to 16 ft. wide with 12" eaves Follow the chart above for Part #'s and quantities for each home set. 5' 4" No Frame Ties No Torque Probe No Stabilizer Plates No ongitudinal Anchors No Beam Clamps No 5 Ft. perimeter anchors Deduct Foundation Pad Cost for Each Pier Set with ector Pads 2' Max. 2' Max. Required Anchor Spacing in Florida (48" Anchor ength Approved for all Soil Classes) ector / 2SD Combination (two Pads, 2 SD kits & 1 ector kit shown) Note: Some manufacturers may require (5 ft.) anchors for higher loads at shear walls and/or marriage line supports. See manufacturers installation manual for specifics. ector System (two pads & one hardware kit shown)
5 Combine TIE DOWN's ongitudinal ( 2 SD) and ector Systems and SAE! (Double Section Home) Home 2SD* ector SD/ector ector Stabilizer Frame Beam ongitudinal ength Systems Systems Pads Straps Plates Ties Clamps Anchors in Ft. #59026 #59024 # ' - 38' 4* ' - 57' 4* ' - 76' 4* ' - 91' 4* * Strut lengths are purchased separately (2 per system) Follow the above chart for Double Section Homes
6 ongitudinal Stabilization Devices for Florida As an alternate to installing longitudinal anchors and stabilizer plates, the installer may use longitudinal stabilizing devices approved by the state, including Tie Down's SD (ongitudinal Stabilization Device). The use of two SD systems on a single section home replaces all eight longitudinal anchors, stabilizer plates and straps. Four SD systems on a double section home replaces sixteen longitudinal anchors, stabilizer plates and straps. 2 Note: SD pads provide 3 sq. ft. of bearing support per system NEW One Piece Pad 1. ongitudinal Foundation Pad 2. Beam Clamp (2 per system) 3. ongitudinal Strut (2 per system) 4. Tie Bracket (2 per system) Example of Possible Placement: Part # Description Single Section Home up to 18 feet in width. Double Section Home up to 36 feet in width. 1. Determine where the longitudinal Stabilizing Device will be installed on the home. 2. Place one 2 SD pad centered under the beam. NOTE: Press pad into the ground so that the cleats are below ground level. 3. Slide tie brackets into pad SD Pad SD Hardware Kit Includes: 2 tie brackets & 2 beam clamps ongitudinal Strut 30" for use up to 18" high piers (two block piers) ongitudinal Strut 39" for use up to 24" high piers (three block piers) ongitudinal Strut 44" for use up to 32" high piers (four block piers) ongitudinal Strut 53" for use up to 40" high piers (five block piers) ongitudinal Strut 65" for use up to 48" high piers (six block piers) 4. Build pier on 2 SD pads between tie brackets. 5. Install beam clamps on either side of pier. Attach 2 SD braces to beam clamps and tighten all bolts ,193
7
INDEX PAGE RELEASE SECTION NUMBER DATE
INSTALLATION INSTRUCTIONS For Wind Zone 1 (other Wind Zones available on request) Version 11/20/2002 INDEX PAGE RELEASE SECTION NUMBER DATE Approval INTRODUCTION 2 2/26/2001 GENERAL INSTALLATION 3 2/26/2001
More informationTechnologies, Inc. Installation Instructions for Anchors & Components. Rev PAGE 1 / 11
Installation Instructions for Anchors & Components PAGE 1 / 11 GROUND ANCHOR INSTALLATION INSTRUCTIONS NOTE: 1) The tensioning bolt can be inserted in the head from either side. 2) In areas of severe cold
More informationManufactured Housing Installation Instructions TIE DOWN ENGINEERING
Manufactured Housing Installation Instructions Provided by TIE DOWN ENGINEERING (Revised: 5/7/2015) Table of Contents Subject Description Page ABS Pads ABS Pad Installation 18 ABS Pads ABS Pad Listings
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationOffering a full range of anchoring and tie down systems including:
Offering a full range of anchoring and tie down systems including: BE SURE TO CONSULT LOCAL REGULATORS FOR CODE QUESTIONS AND THE MANUFACTURERS INSTALLATION MANUAL FOR PROPER MATERIALS. Anchors Pan Systems
More informationULTRA SPACE SAVER SQUARED Installation Instructions
Installation Instructions The Ultra Space Saver Squared has several steps for installation. Note that the single and double sided setups and parts are different. Make sure you follow the instructions according
More informationAssembly Instructions
18' W x 10' H or 12' H Peak Style Frame Assembly Assembly Instructions Before you start: 2+ individuals recommended for assembly, approximate time 3 hours. Recommended tools: Power Drill, Safety Glasses,
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationThe Queen Quilter Professional Quilters Kit Frame
The Queen Quilter Professional Quilters Kit Frame Assembly Instructions Table of Contents: Before you begin......................... Pg. 2 Wood parts............................. Pg. 3 Hardware..............................
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS PRINTED IN USA Assembly Instructions Include: P/N: LL-04-5 Step : Site Preparation Step 0: Guard Rail Installation Step : Leg Assembly Step : Stairs Step 3-8: Setting the Stage Step
More informationINSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM
SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the
More informationRayport G Eco Dealer Kit
Rayport G Eco Dealer Kit Installation Guide www.aetenergy.com Supporting a Cleaner, Greener Tomorrow 1. Table of Contents 1. Table of Contents P2 2. Installer Notes P3 3. Parts List P4-7 4. Tool List P8
More informationUPM 6X. UPM 6X Standard stock Tee socket sized for 5" schedule 40 or 80 Pipe. Page 1 of 8
Page 1 of 8 UPM 6X A. TEE SOCKET: 6 O.D. PIPE SOCKET TO FIT OVER 5 SCHEDULE 40 OR 80 STEEL PIPE B. CROSS PIECE: 2 X 2 X 1/8, LENGTH DEPENDENT ON MODULE USED, SQ. TUBE 2 PLACES C. LONGITUDINAL: 2 X 2 X
More informationClassic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationHeavy Duty Ceiling Tilt Mount Installation Manual
HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationClassic Roll Tarp. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Classic Roll Tarp Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationULTRA SPACE SAVER Installation Instructions
Installation Instructions The Ultra Space Saver has several steps for installation. Note that the single and double sided setups and parts are different. Make sure you follow the instructions according
More informationOutdoor Water Solutions, Inc. 9 Backyard Windmill. Installation Manual
Outdoor Water Solutions, Inc. 9 Backyard Windmill Installation Manual Customer Service: -866-7-6 Website: www.outdoorwatersolutions.com Springdale, Arkansas 72762 Phone: -866-7-6 Fax: (79) 750-978 Thank
More informationRange height adjustable assembly
Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces
More informationMSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit for use with Island Display Skybox
INSTALLATION INSTRUCTIONS MSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit for use with Island Display Skybox The MSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit provides a sturdy support for LCD displays
More informationThanks for shopping with Improvements! 8 ft. Retractable Window Awning Item # (Fits windows/doors from 73 to 96 wide)
Thanks for shopping with Improvements! 8 ft. Retractable Window Awning Item #511412 (Fits windows/doors from 73 to 96 wide) Note: Read these instructions carefully before assembling. Find a clean, smooth
More informationPATRIOT DOCKS ASSEMBLY INSTRUCTIONS
6/1/2008 PATRIOT DOCKS ASSEMBLY INSTRUCTIONS Congratulations on your new Patriot Dock purchase. This manual contains instructions to assemble basic dock configurations for use at typical shoreline application.
More informationBEST PRACTICE GUIDE. Socket Bases. Working with Concrete Slabs
Working with Concrete Slabs When working with concrete slabs the barrier protection can be erected in three ways - with socket bases, adjustable slab edge brackets and multi slab clamps. Socket Bases 1
More informationOutdoor Water Solutions, Inc. Small Backyard Windmill. Installation Manual
Outdoor Water Solutions, Inc. Small Backyard Windmill Installation Manual Customer Service: 1-866-471-1614 Website: www.outdoorwatersolutions.com Springdale, Arkansas 72764 Phone: 1-866-471-1614 Fax: 1-479-750-9178
More informationClopay Models 835/837 Sliding Door System Installation Guide
Clopay Models 835/837 Sliding Door System Installation Guide The aim of this instruction is to guide you through the process of construction and fitting of Sliding Doors. Due to the number of sizes available
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationReal Life Ninja Starter Pack 1 Assembly Instructions
Real Life Ninja Starter Pack 1 Assembly Instructions MATERIALS: Warped Wall 3 - Main Sections (Only 2 Sections for 10 Warped Wall) 8 3 deck screws for joining sections inside of Warped Wall 2 Rock Wall
More informationReal Life Ninja Complete Starter Pack (14ft. Warped Wall) Assembly Instructions
MATERIALS: 3 - Main Sections (Only 2 Sections for 10 ) 8 3 deck screws for joining sections inside of 2 Rock Wall Panels (with pre-installed t-nuts. Top panel comes with ladder mounting block preinstalled.)
More informationASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355
ASSEMBLY AND CARE INSTRUCTIONS VERSION: 8920100 (Revised 06/16) JUST FOR KIDS 355 SALES AND SERVICE spiethamerica.com Canada and International 135 Forestview Road, PO Box 40 Orillia, Ontario, Canada L3V
More informationGeneral Guidelines:
ASSEMBLY INSTRUCTIONS Congratulations on your new Patriot Dock purchase. This manual contains instructions to assemble basic dock configurations for use at typical residential shoreline application. Please
More informationPORTABLE ADJUSTABLE BASKETBALL SYSTEM
Instruction Manual PORTABLE ADJUSTABLE BASKETBALL SYSTEM P A R T S L I S T 5 1/2 and 8 safe play clearance Item Qty Description Item Qty Description A 1 Portable Base Assembly M 4 1/2 Lock Nut B 2 Front
More informationM2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4
M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...
More informationLab Style Table Frame Part No Assembly Guide Automation Technology
Ergonomic Workstations Lab Style Table Frame Part No. 8 0 Assembly Guide 7 90 70 Automation Technology SPECIFICATIONS Lab style frame part number... 80 Height... 70 mm (8.") Width... 90 mm (.7") Depth...
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationPack Mount Instructions:
Pack Mount Instructions: STEP 1 Mounting upright base to desired surface If mounting to a surface with an accessible backside (such as a thin walled container): Option 1 Discard the Round Mounting Disk
More information3,500/4,500lb. Vertical Cable Feighner Lift
3,500/4,500lb. Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety precautions
More information1: profile cross section. FD- profile. for sidewalls + backwalls. eaves profile. curved roof profile. Z - profile (alongside frame) L 60 x 60
1: profile cross section FD- profile for sidewalls + backwalls eaves profile curved roof profile Z - profile (alongside frame) L 60 x 60 for backwall Image 2: 1.) Insert feet from below in square tubes
More informationUPM 6X Custom. UPM 6X CUSTOM Standard stock Tee socket sized for 5" schedule 40 or 80 Pipe. Page 1 of 8
Page 1 of 8 UPM 6X Custom A. TEE SOCKET: 6 O.D. PIPE SOCKET TO FIT OVER 5 SCHEDULE 40 or 80 STEEL PIPE B. CROSS PIECE: 2 X 2 X 3/16, LENGTH DEPENDENT ON MODULE USED, SQUARE TUBE 2 PLACES C. LONGITUNDINAL:
More informationSTRATUS SHELTER. Take bike parking to new heights
Take bike parking to new heights The Stratus Shelter is a striking bike shelter option for any transit station, university campus, or multi-family residential building project. It is constructed of American
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More information.84M Ku-Band Rx/O Antenna System
4096-644 Revision A May 9, 2003 ASSEMBLY MANUAL.84M Ku-Band Rx/O Antenna System PRODELIN CORPORATION 1500 PRODELIN DRIVE NEWTON, NC 28658 .84M Ku-Band Rx/O Antenna System A ORIGINAL RELEASE 5/9/2003 A.Hahn
More informationRoll In W/L Dock PAGE 1
Roll In W/L Dock PAGE 1 1 2 3/8 X 1 CARRIAGE BOLT SS 3/8 FLANGE NUT BRASS 3 4 1/2-13 X 1.25 SQ BOLT SS 1/2 SQ NUT BRASS 5 3/8-16 X 2.5" BOLT SS PAGE 2 6 7 BRACE BRKT SINGLE AXLE TUBE 8 9 3" AXLE WASHER
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationKwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Installation Instructions Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationSAVVY OFF ROAD GAS TANK SKID INSTALLATION INSTRUCTIONS
It is best to work with a fuel tank that has the least amount of fuel in it as possible. Thank you for purchasing the best skid on the market. Please follow these instructions and your installation should
More informationSales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.
Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)
More informationSS1062, SS10621 & SS10621E Free Standing PWC & Fishing Boat Hoist SS1062 SS10621 SS10621E
SS1062, SS10621 & SS10621E Free Standing PWC & Fishing Boat Hoist SS1062 SS10621 SS10621E Midwest Industries, Inc. Page 1 Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003231 REV A 1/25/05 Bundles
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationKIT ASSEMBLY INSTRUCTIONS
JUMPING JACK TRAILER KIT KIT ASSEMBLY INSTRUCTIONS A torque wrench (provided in the in-store tool kit) is required to assemble this trailer kit. Torque is a twisting (ft.-lb.).copy force measured in foot-pounds
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationC4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS
C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect
More informationCSS Central Mount System
CSS-20 Installation Manual CSS-20 Safety Notifications Below are the installation instructions for the CSS-20-2 Long Span Beam Mounting System. Please read these safety notifications prior to beginning
More informationInstruction Sheet For: SCM-2
Instruction Sheet For: SCM-2 For more information, please contact us at: 345 Log Canoe Circle, Stevensville, Maryland 2666 Toll Free: 877.28.269 Phone: 40.643.6390 Fax: 40.643.665 www.videomount.com 27
More informationSteel Strong-Wall Shearwall Installations
Steel Strong-Wall Shearwall Installations Connector Training for Contractors Series Name: (800) 999-5099 www.strongtie.com Industry Terms Steel Strong-Wall Every day we work hard to earn your business,
More information19 to 39 TV WALL MOUNT - FULL MOTION
19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5
More informationPRO / PL SHOE REPLACEMENT & CONVERSION INSTRUCTIONS
PRO / PL SHOE REPLACEMENT & CONVERSION INSTRUCTIONS REIMANN & GEORGER CORPORATION HOISTING PRODUCTS BUFFALO, NY P/N 610096 10/19/05 Read the following instructions thoroughly before starting work to identify
More informationHorse Shelter 12 x
Horse Shelter 12 x 15 76110678 Hardware Kit 76900228 THANK YOU FOR PURCHASING THIS PRODUCT Behlen Country has been in the business of providing quality products for more than 75 years. Our products will
More informationRIDGE MAST MOUNT (RMM)
May 5, 009 Revision E ASSEMBLY MANUAL (RMM) General Dynamics Satcom Technologies 1500 PRODELIN DRIVE NEWTON NC 8658 88-464-4141 www.gdsatcom.com 1.0 INTRODUCTION: 1.1 Features: The Ridge Mast Mount (RMM)
More informationUPM 10X and 10XHD A. TEE SOCKET: 7 O.D. PIPE SOCKET TO FIT OVER 6 SCHEDULE 40 OR 80 STEEL PIPE
Page 1 of 8 UPM 10X and 10XHD A. TEE SOCKET: 7 O.D. PIPE SOCKET TO FIT OVER 6 SCHEDULE 40 OR 80 STEEL PIPE B. CROSS PIECE: 3 X 3 X 3/16, LENGTH IS 60 (10X) or 78 (10XHD), SQ. TUBE 2 PLACES C. LONGITUDINAL:
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationINSTALLATION INSTRUCTIONS
B E Fig. 1 A J INSTALLATION INSTRUCTIONS REESE Steadi-Flex K H 66557 250LB 400LB Weight Distributing Kits 66558 400LB 600LB G D C F A 1 BALL MOUNT B 1 DRAW BAR C 2 3/4-10 x 4-1/2" GR.8 HEX HEAD BOLT D
More informationTOYOTA TUNDRA CARGO DIVIDER Preparation. Part Number: PT
Preparation Part Number: PT767-34070 Kit Contents 1 1 Divider Screen 2 1 LH Bracket with Warning Label 3 1 RH Bracket without Warning Label NOTE: Part number of this accessory may not be the same as the
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationFootball Goal Posts MODEL SERIES: FGP400 and FGP600 series
Football Goal Posts MODEL SERIES: FGP400 and FGP600 series Installation and Maintenance Instructions Please read all instructions before attempting installation of these units SAVE THESE INSTRUCTIONS FOR
More informationBBF Series Blower Base Frame Assembly Instructions Rev.: BFA-9105
BBF Series Blower Base Frame Assembly Instructions Rev.: BFA-9105 These assembly instructions are to be used as a general reference guide to facilitate assembly. Please consult the blower, bushing, sheave,
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationTop Closure Kit Accessory for Music Library System
Assembly Instructions Top Closure Kit Accessory for Music Library System Contents Required Tools.....................................2 Installation Requirements............................2 Fasteners -
More informationRayport G Eco Dealer Kit
Rayport G Eco Dealer Kit Installation Guide Contents 1. Installer Notes..... P2 2. Parts List........ P3-7 3. Tool List.... P8 4. Assembly.... P9-19 www.aetenergy.com Supporting a Cleaner, Greener Tomorrow
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationTHE ROGUE TM FUNSLIDE TM
THE ROGUE TM FUNSLIDE TM ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * * S.R. SMITH ROGUE TM FUNSLIDES TM ARE MANUFACTURED FOR INSTALLATION AND USE ON RESIDENTIAL INGROUND POOLS ONLY. ROGUE
More informationRANGE DIGITAL HANDSET OPERATION. 1. Panel. 2. Initialization Procedure. 3. Move Up & Down. 4. Set Memory Positions. 5. Move to the Memorized Positions
INSTRUCTION SHEET #2577INS PART #1730534 DIGITAL HANDSET OPERATION OPERATION INSTRUCTIONS 1. Panel 1 Button: Preset 1 2 Button: Preset 2 3 Button: Preset 3 S Button: Select Display: Reads in 1 / 2 " Increments
More informationFLOE quick attach & standard sectional dock and leg kits
FLOE quick attach & standard sectional dock and leg kits assembly instructions KIT P/N 510-02550-00 X-SHALLOW KIT P/N 510-02551-00 SHALLOW KIT P/N 510-02552-00 MEDIUM KIT P/N 510-02553-00 DEEP WARNING
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationTable of Contents for Standard Duty Poly Blade Arctic Standard Duty Poly Blade 84" & 90" (Blade, Quadrant & T-frame)....2 Important note: Lift frames for this specific blade are listed below: Lift Frame
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More informationInstallation Instructions
Column & Beam Units with Debris Netting Installation Instructions Laminated Wood Systems, Inc. Seward, Nebraska 800-949-3526 2015 LWS, INC. AVR-NET INSTALL 05-12-16 AVR Installation Notes 1 Safety The
More informationTrak-Slider Instructions
Trak-Slider Instructions 1/4-20 x 3/4" Hex Head Bolt 1/4-20 Flanged Hex Nut Gusset 1/4-20 x 1/2" Allen Cap Screw 1/4-20 Nylock Nut Rivet 1/4-20 x 3/8" Pan Head Phillips Machine Screw 1/4 USS Flat Washer
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationMONKEY BARS OVERHEAD RACK INSTALLATION
MONKEY BARS OVERHEAD RACK INSTALLATION Thank you for purchasing the New Monkey Bars Overhead storage rack. The most innovative overhead rack on the market WARNING THE PROPER INSTALLATION OF THIS STORAGE
More information1. Layout. Step 1. Step 2. Step 3. Fig. 1
1-3/8 Panel Clamp Tools You Will Need: Tape Measure, Mason s String, Stakes, Hole Digger, Shovel, Level, Wheelbarrow, Wrenches or Adjustable Wrench, Hacksaw, Pliers, Cutting Pliers, Fence Stretcher and
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More informationInstallation Instructions for Solar Snow Pad (SSP-T-3)
Installation Instructions for Solar Snow Pad (SSP-T-3) Warning- Do not use this product on solar arrays where the calculated array snow loads exceed 50 pounds per square foot (psf). Most solar panels are
More informationINS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)...
INS-88.500-0A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Unpacking the KSCR... 2 2. Splicing the KSCR (If Required)... 4 3. Assemble Curb and Rail Corners... 5 4. Install Cross Bracing (If Required)...
More informationIN 578. Tools Required. Torque Specification: 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench.
Tools Required 2011-C Ford F250/F350 No Drilling into Vehicle is Required 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench FL277 x 1 Torque Specification: 1/4 Bolts - 6 Ft Lbs.
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationBoat Lift Canopy Frame Assembly Instructions
Patriot Docks Boat Lift Canopy Frame Assembly Instructions Helpful Tips: Assembling and installing the canopy frame and cover is a two person job. Additional help makes installation easier and is recommended.
More informationE-Z GROW HOBBY GREENHOUSE. I n s t r u c t i o n M a n u a l & D i s c l a i m e r s
E-Z GROW HOBBY GREENHOUSE I n s t r u c t i o n M a n u a l & D i s c l a i m e r s Contractors/Installers Note: This manual is the property of the customer. Please leave it in the possession of the customer.
More information6a. Eight Steps to Chain-Link Fence Installation
6a. Eight Steps to Chain-Link Fence Installation Before You Start You will need the following tools to install your chain-link fence: Post hole digger Wheelbarrow, shovel and hoe for mixing concrete Tape
More informationIndex Pipe Hangers and Straps
Index Pipe Hangers and Straps Fig. 1 Standard Clevis Hanger MSS-SP-69, Type 1 WW-H-171E, Type 1 Page 14 Fig. 1CI Clevis Hanger for A.W.W.A. Page 16 Fig. 81 Clevis Hanger WW-H-171E, Type 12 Page 70 Fig.
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationSWAY BRACE PIPE ATTACHMENT FIG. 010
Function: Designed for bracing pipe against sway and seismic disturbance. The pipe attachment component of a sway brace system used in conjunction with a PHD Manufacturing structural attachment fitting,
More informationINS A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Verify Curb Installation Required Installation Tools...
INS-88.300-0A KSR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Verify Curb Installation... 2 2. Required Installation Tools... 2 3. Unpacking the KSR... 3 4. Attach KSR Bottom Rail to Curb... 5 5. Attach
More informationGROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02
GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.
More informationPlug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions
www.lightorama.com Plug-n-Show Stake Down Pixel Tree Kit 16 strips of 25 pixels Assembly Instructions Read all instructions before you start Kit assembly! STEP 1. Check that all parts are included Parts
More informationS OLAR RADIATION S HIELD MANUAL
S OLAR RADIATION S HIELD MANUAL This instruction manual is designed to take you step-by-step through the process required to assemble and mount your Solar Radiation Shield. Please take the time to read
More information