Figure #1 - ATE-ASE & UTE-USE Shower Door Assembly
|
|
- Philomena Jackson
- 6 years ago
- Views:
Transcription
1 Figure #1 - ATE-ASE & UTE-USE Shower Door Assembly Refer to FIG #3A or 3B For detail and orientation of towel bar and pull assemblies. Page
2 Figure # 2 - Shower Door Assembly - Side View Figure # 3a - Shower Door Assembly - Top View Page
3 Figure # 3b - Shower Door Assembly - Top View (Refer to Euro Towel Bar Installation Instruction) Figure # 4 Figure # 5 FIG. #6 - Top View - Looking Down at the sill with Panel Installed In Header. CORRECT INCORRECT Page 3
4 ATE-ASE & UTE-USE Parts List ITEM PART # DESCRIPTION QTY. ITEM PART # DESCRIPTION QTY TUB HEADER AVG-1 CENTER GUIDE EURO TUB HEADER AVB-2 BUMPER GUIDE STAY CLEAN SILL SILL TO JAMB CLIP TUB JAMB #8 X 1-1/2 FHPHSMS 6 5 FIG. 3A STD. TOWEL BAR ASSY WALL ANCHOR 6 6 FIG. 3B EURO TOWEL BAR ASSY #6 X 3/8 PHPHSMS GLASS SHOE HANGER BRACKET ASSY SLIDING GLASS PANEL ADJUSTMENT WRENCH ATE-ASE & UTE-USE Assembly Instructions SAFETY WARNING: These installation instructions must be followed to ensure proper operation of the door and to reduce the risk of serious injury. Any deviation from these instructions can result in a serious safety hazard. All exposed ends of aluminum that are rough, sharp or jagged due to the metal being cut, drilled or damaged should be deburred, smoothed or rounded by the installer before installation. Failure to do so could result in serious injury to the user of the enclosure. Any part of the swinging glass panels hitting any unprotected bathroom obstruction or metal or glass component of the shower door itself, may indicate improper installation and could lead to serious injury. Installers must correct the deficiencies before allowing the door to be used. STEP 1 - STAY CLEAN SILL: Measure wall to wall 1/2 above the tub rim. Subtract 1/16 from this dimension and cut the Stay Clean Sill (Item # 3) to this length. NOTE: It may be necessary to file a radius on the ends of the Stay Clean Sill to fit snugly against the wall. Set the sill onto the tub rim or shower sill. Make sure that the reveal on the tub rim is even all the way across. Mark the location of the Stay Clean Sill on the tub rim at the point where it meets each wall so that the sill can be repositioned correctly later. The Stay Clean Sill must now be notched to accept the Sill to Jamb Clips that lock the Sill into place. Remove the Stay Clean Sill from the tub rim. Take one of the Sill to Jamb Clips (Item #11) and, using it as a template, slide it into one end of the Stay Clean Sill as shown in FIG. #4. Be sure that the clip is oriented as in the picture with 1/8 x 1/8 neck portion of the clip pointing up. Mark the neck of the clip onto the sill. Using a standard 1/8 thick medium file, cut a notch that is 1/8 deep. This will allow the clip to be flush with the end of the sill. Repeat this procedure with the opposite end of the sill. Find the center of the Stay Clean Sill, and place the Center Guide (Item #9) into place. Using the factory hole as template, drill through the hole into the sill with a #32 wire gauge. NOTE: Do not attach the Center Guide at this time. With the Sill to Jamb Clips in place, set the Stay Clean Sill back onto the tub rim and realign with location marks made earlier in this step. Use masking tape to temporarily hold the sill in place. Page 4
5 STEP 2 - TUB JAMBS: Place one of the Tub Jambs (Item #4) against the showerhead wall. IMPORTANT NOTE: The Tub Jamb should be oriented so that the channel that has the countersunk installation holes in it is to the inside of the shower enclosure to allow the inside panel to close at the shower head wall, which is necessary for water protection. Please refer to FIG. #3A for proper orientation. The lower end of the Tub Jamb should rest on the horizontal surface of the Stay Clean Sill, and over the vertical leg of the 90 Sill to Jamb Clip. Using a level, plumb the Tub Jamb and mark all three factory hole locations onto the wall using the Tub Jamb as a template. Remove the Tub Jamb and drill the three holes using a 3/16 drill bit. Insert three Wall Anchors (Item #13). The end of the Stay Clean Sill must now be sealed to prevent water from leaking outside of the enclosure. Apply caulk at this time. Please refer to FIG. #5 for sealant location. Replace the Tub Jamb and realign with the holes. Position one Bumper Guide (Item #10) over the top and bottom holes then secure the Tub Jamb with three #8 X 1-1/2 FHPHSMS (Item #12). For the second Tub Jamb, you must first check to make sure that the Stay Clean Sill has not moved. Readjust if necessary. Place the second Tub Jamb on the wall opposite the shower head. This jamb must be reversed from the first one that is already installed by orienting the channel with the countersunk installation holes to the outside of the shower enclosure to accept the outside sliding panel. Set the Tub Jamb in place on the horizontal surface of the Stay Clean Sill and over the vertical leg of the Sill to Jamb Clip as the first jamb was done. Using a level, plumb the jamb, but mark only the bottom hole. Remove the jamb and drill with a 3/16 drill bit. Install one Wall Anchor (Item #13), then position a Bumper Guide (Item #10) over the bottom hole of the jamb and secure with one #8 X 1-1/2 FHPHSMS (Item #12). This will allow the Tub Jamb to be moved side to side for final adjustment later. STEP 3 - TUB HEADER: Measure wall to wall at the top of the Tub Jambs, then subtract 1/16 from this dimension and cut the Tub Header (Item #1 or Item #2) to its finished length. Set the header in place over the top of the Tub Jambs. Be sure that the roller channels of the header are resting firmly on the Tub Jambs. Make sure that the Tub Jamb with only one screw in it is snug, but still is able to move side to side. STEP 4 - PANEL INSTALLATION: Hang the outside panel only in place in the Header. Make sure that the rollers are firmly seated in the Header roller channel. Slide it all the way towards the fully secured Tub Jamb Standing outside of the shower, hold the Header at the top where it meets the unsecured Tub Jamb. BE VERY CAREFUL TO KEEP CONTROL OF THE HEADER SO THAT THE SLIDING GLASS PANELS CAN NOT FALL. Slowly, move the sliding panel to the middle of the opening. Adjust the header inside to outside, seeking a point where the outside face of the panel laying against the vertical leg of the Stay Clean Sill, exactly parallels it. The full width of the glass panel must contact the T-Fin of the Stay Clean Sill, not hitting on one edge or the other only. Now the panel is tracking on the same line as the Stay Clean Sill (Fig #6). Mark the position of the Tub Jamb onto the wall. Slide the panel back to the secured Tub Jamb and remove the sliding panel and set it in a safe place. Move the Tub Jamb back to the marked location on the wall and mark the final two hole locations. Remove the Tub Jamb and drill the holes with a 3/16 drill bit. Insert two Wall Anchors, (Item #13). Realign the Tub Jamb and secure with three #8 X 1-1/2 FHPHSMS, (Item #12), attaching a Bumper Guide, (Item #10), with each screw (Fig. #1). Make sure the Bumper Guides are oriented to accept the proper panel. Install both of the sliding glass panels as you did earlier in this step, then install the Center Guide, (Item #9). Page 5
6 STEP 5 - TOWEL BARS AND PULLS: Please determine the correct towel bar for your model, Accent or Euro, before proceeding. WARNING: This shower door should not be installed without grommets. The grommets prevent the glass from touching the metal screw. If the metal touches the glass, the glass can break and create a serious safety hazard. ACCENT TOWEL BAR - Figure #3A: On the outside Sliding Glass Panel, measure between the towel bar holes from center to center. Cut the Towel Bar (Item #5) to this dimension. For the pull assemblies, start by sliding the glass panels to their proper closed position. You will notice that the two center holes are inaccessible because of the overlap in the panels. Make them accessible by sliding each panel to the opposite wall. Now the holes are at the outside edges. Begin installing the pull assemblies with the panels in this position. Start by installing the Male and Female Clear Plastic hole plug into the exposed hole on the inside panel. Through the exposed hole on the outside panel, place one Grommet in the hole, followed from the inside with a Back Up Plate and one #8-32 X 7/8 FHPHMS that will thread into the Towel Bar Bracket on the outside of the panel. Follow the detailed drawing in FIG. #3A, for proper orientation and assembly. If it is necessary to allow the glass panels to totally bypass each other, contact your Agalite representative and ask for part number 3013 in the appropriate color. EURO TOWEL BAR - Figure #3B: Please refer to the instructions sheet included In the Euro Towel Bar Package. STEP 7 - PANEL ADJUSTMENT: If either panel is skewed or rubs against the sill, adjust the panels by loosening the hex nut on any of the Hanger Brackets with the Adjustment Wrench (Item #16), provided in the parts kit, and compensate the panels for the wall conditions. NOTE: The panels need not be removed from the header to adjust. Attach the header assembly to the Tub Jambs by drilling, from the inside of the shower, through the header into the Tub Jambs with a 1/8 drill bit. Secure with two #6 X 3/8 PHPHSMS (Item #14). STEP 8 - CAULK: Apply a bead of caulk along the entire inside of the enclosure where it meets the walls and base. Page 6
Page 1. FIG. #1 - Shower Door Assembly SHOWER & BATH ENCLOSURES BUILT TO LAST A LIFETIME HANDLE ASSEMBLIES REMOVED FOR CLARITY.
FIG. #1 - Shower Door Assembly 29 1 2 1 6 9 9 5 HANDLE ASSEMBLIES REMOVED FOR CLARITY. 25 25 PLEASE REFER TO FIG. #2 FOR INSTALLATION 26 12 17 18 18 17 10 3 11 7 10 8 Page 1 FIG. #2 - Top View 5 21 10
More information3/16 FRAMELESS SERIES BY-PASS TUB AND SHOWER ENCLOSURES #3344, 3345, 3037
/ FRAMELESS SERIES BY-PASS #, 5, 07 PLEASE READ THOROUGHLY BEFORE STARTING INSTALLATION Item 5 7 8 9 0 5 7 8 Part # 09/050 0 05 A05 8 0 0 0 70 0 09 5 5 0 0 7 0 Description Tub Header Stay Clean Sill Tub
More informationSLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 90º PANEL
SLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 0º PANEL This instruction sheet applies to the following units. C, C7, C7, C77, C, C7 This instruction sheet also applies to the following units. VTE / VSE
More informationFIG. #1 - ASD & USD 180/280 Shower Door Assembly
FIG. #1 - ASD & USD 180/280 Shower Door Assembly USD180 / 280 Euro Stall Header #1020 16 16 1 16 4 ASD180 / 280 Accent Stall Header #1021 5 3 8 6 7 8 Hinge Assembly: 2220, 2201, 2185, 2271, 2213 18 22
More informationFIG. #1 - ASD-90 & USD-90 Shower Door Assembly
Installation Instructions for the Accent/Euro Collection FIG. #1 - ASD-90 & USD-90 Shower Door Assembly #1021 #1021 1 23 25 2 #1020 6 5 12 #1020 9 24 9 8 Hinge Assembly 2109, 2201, 2212, 2213, 2220 7 Please
More information3/16 FRAMED SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS
/ FRAMED SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS This instruction sheet applies to the following units. C, C, C BS 80, BS 80B, BS 80 0 0 8 Weep holes to inside of curb PLEASE READ ALL
More information3/16 OR 1/4 FRAMELESS SWING DOOR WITH SINGLE INLINE PANEL OR TWO INLINE PANELS
/ OR / FRAMELESS SWING DOOR WITH SINGLE INLINE OR TWO INLINE S This instruction sheet applies to the following units with a magnetic handle. C7, C7, C79 This instruction sheet also applies to the following
More informationFigure #1 - VSNEO Shower Door Assembly
Figure #1 - VSNEO Shower Door Assembly Figure #2 - VSNEO - Top View Figure #3 - VSNEO - Side View Figure #4 - Foam Curb Plug Figure #5 - Magnet Strip Figure #6 - VSNEO - Drip Deflector Preparation VSNEO
More informationInstallation Instructions Models: SESD180, DESD180, MESD180 1/4" Semi-Frameless Door and 3/8" In-Line Panel
Models: SESD180, DESD180, MESD180 Scan this Barcode for Parts Bag BP.3143.NLT Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. IMPORTANT:
More information1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE
INSTALLATION INSTRUCTIONS 1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More information340D / 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340D / 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2016. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More informationInstallation Instructions Models: TRBTE / TRBSE ECBTE / ECBSE 3/8" Frameless Slider
Installation Instructions Scan this Barcode for Parts Bag BP.5003.NTL Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. IMPORTANT:
More informationProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE
INSTALLATION INSTRUCTIONS ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980847 5-1-13 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath
More informationTwo Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More information340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More information640D & 650D SERIES FRAMED BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 640D & 650D SERIES FRAMED BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Page 1 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath Enclosures by Sapa are intended to
More informationMASON SHOWER DOOR INSTALLATION
SKU(s): 939728, 939729 MASON SHOWER DOOR INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing this type of product. Signature Hardware accepts no liability
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER 4400A-4500A
1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER 4400A-4500A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More information640S & 650S SERIES FRAMED BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS Tel: 800-643-1514 www.alumaxshowerdoor.com 640S & 650S SERIES FRAMED BYPASS BATH ENCLOSURES Page 1 of 8 G03915346 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath Enclosures by
More informationInstallation Instructions Models: TRTE290 / TRSE290 ECTE290 / ECSE290 3/8" Frameless Slider with 180 & 90 Panels
3/8" Frameless Slider with 180 & 90 Panels Scan this Barcode for Parts Bag BP.5005.NLT Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully.
More informationInstallation Instructions Models: TRTE290 / TRSE290 ECTE290 / ECSE290 3/8" Frameless Slider with 180 & 90 Panels
3/8" Frameless Slider with 180 & 90 Panels Scan this Barcode for Parts Bag BP.5005.NLT Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully.
More informationInstallation Instructions Models: TRTE180 / TRSE180 ECTE180 / ECSE180 3/8" Frameless Slider & 180 Panel
Scan this Barcode for Parts Bag BP.5004.NTL Thank you for purchasing this outstanding product! This booklet will help you install your units safely and successfully. IMPORTANT: Warnings and General Shower
More informationUnit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS
Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Bypass Door Model: L0516 (Tub Height), L0517 (Shower Height) Rev. 09.20.13 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage.
More informationFrameless Bypass Slider
INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 3/8 or 1/4 Glass Bypass Slider with Exposed Rollers QCI5301 Rev 1 Page 1 Certified 6/5/2017 Tools: To install your New Shower Enclosure, you may
More informationSERIES: CONFIGURATION: MOUNTING PACKAGE: 1200 Door-Door Frameless, sliding door
SERIES: CONFIGURATION: MOUNTING PACKAGE: 1200 Door-Door Frameless, sliding door RDQCI5022 Rev.0 Page 1 Certified 06/01/2016 Tools: To install your New Shower Enclosure, you may need the following: Pencil
More informationFrameless Bypass Slider
INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need
More informationDeluxe Frameless ByPass Bath Enclosures. 340 & 350 Series
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxshowerdoor.com 340 & 350 Series Deluxe Frameless ByPass Bath Enclosures 350D-0517
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER
1/4 FRAMELESS SLIDING DOOR FOR OR SHOWER INSTALLATION INSTRUCTIONS NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) M onda y - Friday 8 :00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER
1/4 FRAMELESS SLIDING DOOR FOR OR SHOWER INSTALLATION INSTRUCTIONS NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) M onda y - Friday 8 :00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary
More informationProLine PL80 HEAVY FRAMELESS BYPASS BATH ENCLOSURE
INSTALLATION INSTRUCTIONS ProLine PL80 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980849 5-1-13 Three-Year Limited Residential Warranty Alumax
More information340 & 350 SERIES DELUXE FRAMELESS BYPASS
BATH ENCLOSURES An Alcoa Company Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com INSTALLATION INSTRUCTIONS 340 & 350 SERIES DELUXE FRAMELESS BYPASS BATH ENCLOSURES Copyright Alumax Bath Enclosures
More informationUNIT No. 8150/9150 SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS NEE INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) UNIT No. 8150/9150 SHOWER ENCLOSURE Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary materials
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More information340 & 350 SERIES BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340 & 350 SERIES BATH ENCLOSURES 800-643-1514 www.alumaxbath.com Copyright Alumax Bath Enclosures 2010. All rights reserved. LIMITED WARRANTY AND REMEDY ALUMAX BATH ENCLOSURES
More informationtile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:
redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 1100 Door-Door Framed sliding doors RDQCI5023
More informationTUB SHOWER Framed Sliding Enclosure
INSTALLATION INSTRUCTIONS 8775-9775 - SHOWER Framed Sliding Enclosure Call Technical Dept @ 1-800-452-2726 QCI1000 Page 1 of 6 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully and inspect
More information3/8 FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS 3/8 FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE QCI-5017 QCI5017 Rev. 3 Page 1 of 9 Certified 12/6/17 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage.
More informationSHOWERGLIDE 600B, 690B, 692B, SERIES
Installation Instructions SHOWERGLIDE SERIES 600B, 60B, 6B, 6B, 65B, 67B IMPORTANT: You should check with your local plumbing or building code agency about this product for compliance before it is installed.
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationFRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A
FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More informationModel 750 Illustrated Installation Instructions Contractors Wardrobe
Model 750 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 26121 Avenue Hall Valencia, CA 9155 (661) 257-77 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 29-6677
More informationFRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
FRAMED SLIDING DOOR FOR OR SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS QCI5023 REV. 0 Page 1 Certified 06/22/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationUnit No. 6150, 7150 Deluxe Framed Sliding Tub/Shower Enclosure
INSTALLATION INSTRUCTIONS Unit No. 6150, 7150 Deluxe Framed Sliding Tub/Shower Enclosure QCI0023 Rev. 1 Page 1 of 8 Certified 8/20/10 MAINTENANCE: Two primary materials are used to manufacture your new
More informationModel 2400/4000 Illustrated Installation Instructions
Model 2400/4000 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MNUFCTURERS 26121 venue Hall Valencia, C 955 (661) 257-77 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 293-6677
More informationFRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274
FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 QCI0274 QCI5274 REV. Rev. 1 0 Page Page 1 1 Date Certified: Certified 06/16/2016 10/01/10 Parts List with wall mount hinges ITEM NO. Part # DESCRIPTION
More informationINSTALLATION INSTRUCTIONS
www.marwincompany.com Kit Number Door Height Rough Opening Height KD200BB68 80 84 ½ KD200BB70 84 88 ½ KD200BB80 96 100 ½ INSTALLATION INSTRUCTIONS 200BB SERIES KD POCKET DOOR FRAME FOR 2 X 4 STUD WALLS
More informationwestern window systems westernwindowsystems.com installation instructions non-pocket 2-1/4 panels
series 2600 multi-slide non-pocket 2-1/4 panels windowsystems.com windowsystems.com movement, which can cause warping and other problems. Frame kit components: Each door will have a head assembly, a threshold
More informationSeries----SP3600A SHOWER DOOR
Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationInstallation Instructions
Arizona Corporate Office 2801 W. Indian School Rd Phoenix, AZ 85017 800 255 1901 PH 602 447 8208 FAX Florida 8100 1 Westside Industrial Dr Jacksonville, FL 32219 855 695 8899 PH 904 786 9025 FAX Illinois
More informationInstallation Instructions
Installation Instructions Alcove Enclosure Before Installation please check that your shower enclosure system is undamaged Please read these instructions carefully March 2015 TOOLS REQUIRED Electric or
More information713C-GP. Pivot Door. Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) (Toll Free) 713C-GP 8/06
713C-P Door Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 (Toll Free) PARTS IST FRAME PACKAE KEY DESCRIPTION PART QTY A SI A195 1 PIVOT JAM A196
More informationtile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:
redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 3000 Door-Door Header, sliding doors RDQCI5301
More informationFrameless Inline Door QCI5254
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied
More informationTools you will need for this install
Arizona Corporate Office 2801 W. Indian School Rd Phoenix, AZ 85017 800-255-1901 PH 602-447-8208 FAX Florida 8100-1 Westside Industrial Dr Jacksonville, FL 32219 855-695-8899 PH 904-786-9025 FAX Illinois
More informationChapter 9. Windows and Exterior Doors
Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail apron
More informationFrameless Fixed Panel Slider
INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need
More informationFOLDING DOOR INSTRUCTIONS
FOLDING DOOR INSTRUCTIONS Please read these instructions carefully and follow them step by step to insure a smooth installation. Most importantly DO NOT open hardware boxes and mix hardware up. Hardware
More information1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A
1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More information463-GP. Swing Door. Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) (Toll Free) 463-GP 5/06
463-GP Swing Technical ssistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 (Toll Free) PRTS LIST FRME PCKGE KEY DESCRIPTION PRT QTY SILL 855 1 JM 942 2 E MGNETIC
More informationUNIT No. 15 & 16 SHOWER DOOR INSTALLATION INSTRUCTIONS
UNIT No. 15 & 16 SHOWER DOOR INSTALLATION INSTRUCTIONS Page 2 of 7 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure; tempered glass and anodized aluminum. To assure a
More informationFIXED SHOWER SCREEN For Wall Mount Hinges QCI5283
FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL
More informationNancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual
Nancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual Thank you for purchasing our 4 Yard Option (4YO) Upgrade Kit. To install this upgrade you are simply going to assemble
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationQCI0029 REV. 1 Page 1 of 11 Certified 07/06/05
QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish
More informationDeauville Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationINSTALLATION INSTRUCTIONS
PARTS LIST ITEM PART DESCRIPTION QTY 73-A 503F 9MM 50G 5A 50E 505S 50H Connector Bracket Door Stops Support Bar Panel Glass Bracket Wall Mount Bracket Rollers Center Guide Recessed Finger Pull Fixed Panel
More information935 RODA VINESSE NEED INSTALLATION HELP? DOUBLE ROLLERS FRAMELESS DOOR INSTALLATION INSTRUCTIONS QCI XX/XX/XXXX. Call BASCO ( )
INSTALLATION INSTRUCTIONS 935 RODA DOUBLE ROLLERS FRAMELESS DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday VINESSE QCI0286 1 XX/XX/XXXX 935 Roda Parts List With double rollers
More informationDouble Frameless Swing Door QCI5247
INSTALLATION INSTRUCTIONS Double Frameless Swing Door QCI5247 WALL MOUNT HINGES QCI5247 REV. 0 Page 1 Certified 06/16/2016 Parts List with wall mount hinges *Quantities may vary **Quantities double where
More information392CV SERIES Stickstall
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxshowerdoor.com 392CV SERIES Stickstall TM Corner Shower Enclosure 392CV-1117 Yes!
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More information1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS
1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More informationA-935 RODA WALL MOUNT HINGES
INSTALLATION INSTRUCTIONS A-935 RODA WALL MOUNT HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time FRAMELESS DOOR / PANEL CELESTA QCI0274 REV.
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232 QCI5232 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More information675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure
INSTALLATION INSTRUCTIONS 675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure Call Technical Dept @ 1-800-452-2726 QCI1003 Page 1 of 9 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully
More informationGARAGE DOOR WITH TORSION SPRING
GARAGE DOOR WITH TORSION SPRING DIMENSIONS 9 WIDTH X 7 HEIGHT (2.74m x 2.13m) IMPORTANT SAFETY INSTRUCTIONS WARNING: Read all instructions and warnings before use. Failure to follow all instructions may
More informationFIXED PANEL SLIDER QCI5241
INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page
More informationPortofino Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino shower enclosure. Please study these instructions
More informationTraditional Wall Mounted Potfiller
TOOLS NEEDED FOR INSTALLATION 1/4 hex wrench (provided in installation kit) 3/32 hex wrench (provided in installation kit) Pencil or marker PTFE tape Small level, or carpenters square Power Drill with
More information300 CV Series. Semi-Frameless Hinged Door. 202 Anderson Ave., Belvue, KS Phone: Fax:
202 Anderson Ave., Belvue, KS 66407 Phone: 800-669-9867 Fax: 800-393-6699 www.onyxcollection.com 800-643-1514 www.alumaxshowerdoor.com 300 CV Series Semi-Frameless Hinged Door 300CV-1117 300cv PARTS LIST
More informationAllora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED
Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating
More informationSHELTON THERMOSTATIC SHOWER PANEL
SKU(s): 413241 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor,
More informationThank you for your order
Installation Guide Thank you for your order Ph: 09-9133110 Fax: 09-9133113 5 Smales Road. East Tamaki, Manukau PO Box 58031 Greenmount, Manukau 2013 AUCKLAND // WELLINGTON // CHRISTCHURCH www.bathroomdirect.co.nz
More informationChapter 9. Windows and Exterior Doors
Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING BASEMENT EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail
More information738 SERIES PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS 738 SERIES PIVOT SHOWER DOOR Copyright Alumax Bath Enclosures 1997. All rights reserved. Page 1 of 8 LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers,
More informationPortofino Case2 Installation Guide
Portofino Case2 Installation Guide vjun16 (for 17 or 24 mm Surface Wall Profile) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino Case 2 shower enclosure.
More informationVersatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series
Versatrac Bypass Door Units, Conventional and Top Track, 300 and 400 Series TM Rough opening width (finished opening width plus 9/16") Notch for top track units (used as frame header) Rough opening height
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationWC INSTRUCTION MANUAL 2 PEOPLE REQUIRED SHOWER DOOR KW002
WC-66-75 INSTRUCTION MANUAL SHOWER DOOR 05.11 2 PEOPLE REQUIRED KW002 IT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS. GENERAL INSTRUCTIONS
More informationSeries 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)
Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration
More informationFRAMELESS FIXED PANEL SLIDER with 90 RETURN
INSTALLATION INSTRUCTIONS FRAMELESS FIXED PANEL NE INSTA ED LLATI SLIDER with 90 RETURN HELP ON? QCI-5151 QCI5151 REV. 1 Page 1 of 14 1-800 C -45-B all ASCO (452Mon 2726 8:00 day - Frida ) A.M. y Easte
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE ()! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated
More information1 PREPARE HEADER AND ROUGH OPENING
CONTENTS. HEADER & TRACK ASSEMBLY. END BRACKET PLAIN 3. FLOOR PLATE.. 8. 4. SPLIT STUD 6 5. CARRIER (987) 6. QUICK RELEASE PLATE (960) 7. DOOR GUIDE SET (9883) 3. 4. 7. 8. BUMPER KIT (988) 9. #8 X 3/4
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Shower Height Swing Door Model: L533 Rev. 09.03.13 MAINTENANCE: Two primary materials are used to manufacture your new Aquatic enclosure; tempered glass
More informationDeauville Installation Guide
vjul16 (for Recessed Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions carefully before
More informationINSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE QCI0011 Rev. 0 Page 1of 10 Certified 10/18/2006 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure;
More informationCAUTION. It is the responsibility of the INSTALLER to ensure that the installation complies with council and or local authority bylaws.
INSTALLATION GUIDE SAPPHIRE ROUND CORNER SLIDING SHOWER CAUTION It is the responsibility of the INSTALLER to ensure that the installation complies with council and or local authority bylaws. Instructions,
More information