MASON SHOWER DOOR INSTALLATION

Transcription

1 SKU(s): , MASON SHOWER DOOR INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing this type of product. Signature Hardware accepts no liability for any damage to the product, home, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team at TOOLS AND MATERIALS: Phillips Screwdriver Silicone Sealant (100% Neutral Cure) Drill Tape Measure Rubber Mallet Drill Bits GETTING STARTED Ensure that you have gathered all the required materials that are needed for the installation. Level Pencil Safety Glasses Hacksaw 1

2 INSTALLATION Top Track (x1) Bottom Track (x1) Panel Guide (x1) Door Panel (Inside/Outside) Towel Bar (x1) Wall Jamb (x2) Bumper Guide (x2) Wall Bumper (x6) Safe Slider Clip (x4) Glass Hanger (x4) Roller (x4) Wall Plug (x6) 1-1/2 Screw (x6) 3/8 Screw (x2) Towel Bar Wrench (2-3/8 Long) (x1) Safe Slider Install Rod (4 Long) (x1) 2

3 outside 1-1/2 Screw inside 3/8 Screw (Viewed from inside of tub/shower) 1-1/2 Screw 3

4 Step 1: Attach rollers (11) to glass hangers (10) on outside door panel (with horizontal towel bar holes) (4). Rollers should be mounted so that the nut that holds it in place is on the same side of the panel as the screw head set into the glass hanger (see inset drawings). Note: The various holes in the glass hanger are used to fine tune the adjustment of the panel to make up for walls that are slightly out of square or plumb. For best results, start with all rollers in the second hole from the top and then make adjustments as needed. screw roller glass hanger Step 2: Attach rollers (11) to glass hangers (10) on the inside door panel (4). Rollers should be mounted so that when the glass is positioned with the holes in the glass on the same end of the opening as the shower head, the rollers are to the inside of the tub or shower. Door Panel (inside panel) Door Panel (outside panel) 4

5 Step 3: Measure opening on bottom and cut bottom track (2) 1/8 shorter than the opening. Step 4: Place wall jamb (3) down over bottom track (2) so that the back of the jamb is between the bottom track and the wall. Using a level to ensure the jamb is plumb, mark hole locations. Rove jamb and drill holes approximately 1-1/2 deep at the marked locations. Important: When drilling into ceramic, glass, or stone, you must use a 1/4 masonry drill bit. If installing onto fiberglass or acrylic, use a 1/8 drill but and discard the wall plugs. Step 5: Repeat step 4 on the other side. L = actual opening - 1/8 Step 6: Run a thin bead of silicone down the entire length of both bottom edges of the bottom track (2). Place the bottom track into position and press firmly into place. Step 7: Push wall plugs (12) into the holes drilled in step 4. Gently tap in using a rubber mallet. Note: If installing on fiberglass or acrylic, skip this step and discard the wall plugs. Step 8: Apply silicone into all three holes on each side of the wall jamb (3). Run 1-1/2 screws (13) through the wall bumper (8) and use to attach the jamb to wall, in top and bottom holes only, on both sides. top view 1-1/2 Screw 5

6 Step 9: Use 1-1/2 screws (13) to anchor wall bumper (8) and bumper guide (7) into the center hole on each side. Step 11: Place top track (1) down over wall jambs (3), as shown /2 Screw 1 Step 10: Measure opening at the top of the wall jamb (3). Cut top track (1) 1/16 shorter than the opening. L = actual opening - 1/16 6

7 Step 12: Install outer door panel (4) by lifting up and into top track (1). Do not lift by the towel bar, and be careful not to bump panel against metal track. interior shower side outer door Step 13: Insert inner door panel (4) by lifting up and into top track (1). interior shower side inner door 7

8 towel bar screw Step 14: Install the towel bar (5). clear sleeve clear sleeve towel bar wrench Step 15: Position panel guide (6) in center of bottom track (2). Drill two 1/8 holes through screw holes in guide and into bottom track. Position panels in guide as shown in inset drawing, and attach guide to bottom track using 3/8 screws (14). 3/8 screw 1/8 drill bit 8

9 Step 16: Install the safe slider clips (9). Step 17: Caulk both sides of the shower door frame to seal. Keep the entire area dry for a minimum of 24 hours. trim safe slider clip if necessary safe slider clip 9 16 caulk all sides safe slider install rod To install safe slider clips, put safe slider install rod (16) into clip and lift onto clip hanger. Pull down, leaving clip 9