SHOWERGLIDE 600B, 690B, 692B, SERIES
|
|
- Randolf King
- 5 years ago
- Views:
Transcription
1 Installation Instructions SHOWERGLIDE SERIES 600B, 60B, 6B, 6B, 65B, 67B IMPORTANT: You should check with your local plumbing or building code agency about this product for compliance before it is installed. basic tools and materials needed TOOLS Measuring Tape Hacksaw with teeth per inch blade Miter Box or Square Electric Drill Drill Bit- 8" and 6" Masonry Bit for ceramic tile- 6" driver-phillips Level Fine File Pencil Center Punch Hammer Safety Glasses Caulking Gun MATERIALS Caulk Masking Tape Mirror panels are made of a tempered safety glass to comply with the federal Glazing Standards. You may notice some distortion in the mirror as tempered glass will not reflect a perfectly true image. This is an inherent condition found in all tempered glass mirrors. how to care for your door NEVER USE SCOURING POWDER, PADS OR SHARP INSTRUMENTS ON METAL WORK OR GLASS PANELS. The use of a squeegee following each shower is recommended to eliminate water spots on the inside of the glass panels. An occasional wiping down with a mild detergent diluted in water is all that is needed to keep the panels and anodized aluminum parts looking new. CAUTION: TEMPERED GLASS CANNOT BE CUT.
2 part names for installation Top Track Roller Bumper Handle Roller Mounting Roller Roller Towel Bar Bracket Handle Towel Bar Bracket Mounting Anchor Bumper Guide Guide Bottom Track Anchor
3 MEASURING FOR BOTTOM TRACK NOTE: If your shower has a curve in the corners at the side walls, be sure to measure distance D above curves. Measure distance D at the flattest part of the tub ledge. CAUTION: If a steel tape is used, be sure to add the width of the case to the measurement. D CUTTING BOTTOM TRACK NOTE: Wear Safety Glasses. Cut bottom track 8" shorter than distance D. Do not cut top track at this time. For best results use a tooth hacksaw blade and a miter box. LOCATING BOTTOM TRACK Place the bottom track on the flattest part of the ledge with the sloping face of the track towards the inside of the shower. Make sure that the space between the wall and track is the same on both ends. Fasten the track with masking tape. Mark the ledge with a soft pencil along the front edge of the track. NOTE: Track must sit flat. If your ledge has a curve in the corners at the side walls or is of fiberglass construction it may be necessary to shape the ends of the track with a file. Bottom Track
4 DRILLING HOLES NOTE: Wear Safety Glasses 6" Diameter Holes " Drill three 6" diameter holes along the groove at the back of each wall jamb as shown. " Approximately " Off Center 5 LOCATING WALL JAMBS AND MARKING HOLE LOCATIONS Place one wall jamb down over end of bottom track. jamb must sit flat against the wall with legs of wall jamb fully engaged with bottom track. NOTE: You may need to shape the bottom ends of jambs to fit units having a curve at the side walls. Bottom Track Inside of Tub Level Use a level to plumb the wall jamb as shown and mark the hole locations. Repeat procedure at opposite end of unit with other jamb. Pencil Bottom Track Inside of Tub 6 DRILLING HOLES NOTE: Wear Safety Glasses Remove bottom track. Lightly center punch the -hole locations for each wall jamb. On ceramic tile, use the center punch to nick the surface glaze. Tap the punch lightly with your hammer so you don t crack the tile. Drill all 6 holes with a 6" drill bit (use a masonry bit for ceramic tile). After drilling, thoroughly clean the tub ledge and insert anchors in all 6 holes.
5 7 CAULKING BOTTOM TRACK Caulk Apply caulk to the caulking grooves on the underside of the bottom track. Apply enough to just barely overfill the grooves. This will give a good seal with the tub ledge. Install bottom track on ledge in location marked earlier. Seal ends of track at wall with caulk. Bottom Track TURN OVER BEFORE INSTALLING ON LEDGE 8 INSTALLING WALL JAMBS AND BUMPERS Install each wall jamb by inserting over the bottom track. Align the holes in the wall jamb with the holes in the wall. Secure the wall jambs with No. 8-8 x " panhead screws provided. NOTE: Through the center hole of each wall jamb, secure a wall bumper with its guiding lip toward the inside of shower. Tighten all wall jamb screws. Bumper (Guiding Lip) Toward Inside of Shower No. 8-8 x " Panhead MEASURING, CUTTING AND INSTALLING TOP TRACK NOTE: Wear Safety Glasses Measure the wall to wall opening at the top of the wall jambs. Cut the top track 6" shorter than the actual measurement to allow for clearance. Use a tooth hacksaw blade and a miter box. CAUTION: If a steel tape is used, be sure to add the width of the case to the measurement. Install the top track over the wall jamb ends. 5
6 0 LOCATING AND INSTALLING BOTTOM TRACK GUIDE NOTE: Wear Safety Glasses Place the panel guide on the bottom track exactly midway between the wall jambs. No. 6- x 5 6" Flathead NOTE: One top edge of the guide fits into a groove at the front of the track. Drill a 8" hole in bottom track through the hole in the panel guide. Fasten panel guide with a No. 6- x 5 6" flathead screw. Midway Between s INSTALLING ROLLERS NOTE: The steel side of roller must be installed against frame. No. 8- x 8" Panhead Using No. 8- x 8" panhead screws, assemble two rollers on each panel as shown. NOTE: The steel side of roller must be installed against frame. FRONT PANEL---- Install the rollers toward the rough side of glass. Glass with patterns, install the rollers opposite the pattern side. INSIDE PANEL----Install the rollers toward the smooth side of glass. Glass with patterns, install the rollers toward the pattern side of glass. (Front Panel) Smooth Side or Pattern Side (Inside Panel) Smooth Side or Pattern Side 6
7 INSTALLING PANELS OUTSIDE OR ROOM SIDE Install the inside panel first. Lift it up inside the top track and hang the rollers on the inside rail of the top track. Lower the panel bottom frame into the bottom track panel guide. Inside Rail Slide the inside panel against the wall jamb on the same side as showerhead. If the panel does not align with the wall jamb nearest the shower head, remove the panel, loosen roller screw(s), move roller(s) in slot to align door panel, tighten screw(s), and rehang panel. Inside Panel Bottom Track Panel Guide OUTSIDE OR ROOM SIDE Lift the outside panel up inside the top track and hang the rollers on the outside rail of the top track. Align with the wall jamb opposite the showerhead. Adjust rollers if necessary, using same procedure as for the inside panel. Outside Rail Outside Panel 7
8 INSTALLING TOWEL BAR BRACKETS AND TOWEL BAR (For Series 600B) Fasten towel bar bracket to each end of towel bar using No. 8-8 x 8" binding head screws. Bracket Install the towel bar to the outside panel away from the tub. Use No. 8-8 x 8" binding head screws to fasten brackets to the panel frame as No. 8-8 x 8" Binding Head INSTALLING TOWEL BAR BRACKETS AND TOWEL BAR (For Series 60B, 6B, 6B, 65B and 67B) Fasten towel bar bracket to each end of towel bar using No. 8-8 x 8" flathead screws. Bracket Install the towel bar to the outside panel away from the tub. Use No. 8-8 x 8" flathead screws to fasten brackets to the panel frame as shown. No. 8-8 x 8" Flathead 8
9 INSTALLING HANDLE No. 8-8 x 8" Panhead Place one plastic handle on the inside panel side frame at the showerhead side. Secure with a No. 8-8 x 8" panhead screw. Inside Panel Handle This Part of Handle Toward Inside of Tub OUTSIDE OR ROOM SIDE CAULKING CAREFULLY CAULK WHERE: (A) jambs and wall meet. (B) Bottom track and wall jamb join. (C) Bottom track and tub ledge meet. Allow caulk to set hours before use.
10 parts list , Brackets and s for Model 600B-5S - Bracket
11 parts list When ordering parts, specify model number, part number, quantity and color. Key No Description Bottom Track Mounting ----No. 8-8 x " Bumper Top Track Front Panel Inside Panel Plastic Handle Roller ----No. 8- x 8" Roller Bracket Bracket ----No. 8-8 x 8" Bottom Track Guide Plastic Anchor Bottom Track Guide ----No. 6- x 5 6" Plastic Handle ----No. 8-8 x 8" Qty. Part Nos. For Door Models 600B-5S 60B-5S 60B-5S 6B-5S 6B-5S 65B-5S 67B-5S 60B-5G 67B-5G S0.0 S0.0 S0.0 S0.0 S0.0 S0.0 S0.0 S0.0 S
Two Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More informationSeries----SP3600A SHOWER DOOR
Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationBASIC TOOLS AND MATERIALS NEEDED. Introduction HOW TO CARE FOR YOUR DOOR
DO IT RIGHT! Use a Kohler Certified Installer, (KCI), for the installation of your Kohler Shower Door. Contact your Kohler Distributor/Showroom or call Kohler at 1-800-4-KOHLER for the KCI nearest you.
More informationIMPORTANT: One Corner Entry Shower Door requires two cartons.
IMPORTANT: You should check with your local plumbing or building code agency about this product for compliance before it is installed. IMPORTANT: One Entry Shower Door requires two cartons. 95302-2-AB
More informationAngled 2200A INSTALLATION INSTRUCTIONS. Series MODEL NOS
INSTALLATION INSTRUCTIONS Angled Series 20A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram of the
More informationModel 750 Illustrated Installation Instructions Contractors Wardrobe
Model 750 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 26121 Avenue Hall Valencia, CA 9155 (661) 257-77 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 29-6677
More informationTUB SHOWER Framed Sliding Enclosure
INSTALLATION INSTRUCTIONS 8775-9775 - SHOWER Framed Sliding Enclosure Call Technical Dept @ 1-800-452-2726 QCI1000 Page 1 of 6 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully and inspect
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Bypass Door Model: L0516 (Tub Height), L0517 (Shower Height) Rev. 09.20.13 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage.
More informationUNIT No. 8150/9150 SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS NEE INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) UNIT No. 8150/9150 SHOWER ENCLOSURE Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary materials
More informationFRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A
FRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE 6150A-7150A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER 4400A-4500A
1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER 4400A-4500A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More informationFRAMED SLIDING DOOR FOR TUB OR SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
FRAMED SLIDING DOOR FOR OR SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS QCI5023 REV. 0 Page 1 Certified 06/22/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and
More informationUnit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS
Unit No. 4400, 4500 Classic Frameless Sliding Tub/Shower Enclosure INSTALLATION INSTRUCTIONS MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized
More informationtile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:
redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 1100 Door-Door Framed sliding doors RDQCI5023
More informationUnit No. 6150, 7150 Deluxe Framed Sliding Tub/Shower Enclosure
INSTALLATION INSTRUCTIONS Unit No. 6150, 7150 Deluxe Framed Sliding Tub/Shower Enclosure QCI0023 Rev. 1 Page 1 of 8 Certified 8/20/10 MAINTENANCE: Two primary materials are used to manufacture your new
More informationInstallation Instructions with 90 Degree Return Panel -- Model E-DP9. Model Semi-Frameless Door & Panel
6//5 Model Semi-Frameless Door & Panel Installation Instructions with 90 Degree Return Panel -- Model E-DP9 IF YOU NEED REPLACEMENT PARTS OR HAVE INSTALLATION QUESTIONS, PLEASE CALL OUR CUSTOMER SERVICE
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5233 QCI5233 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER
1/4 FRAMELESS SLIDING DOOR FOR OR SHOWER INSTALLATION INSTRUCTIONS NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) M onda y - Friday 8 :00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary
More information675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure
INSTALLATION INSTRUCTIONS 675 Quick N Stall Neo Angle Framed Hinge Shower Enclosure Call Technical Dept @ 1-800-452-2726 QCI1003 Page 1 of 9 Certified 10/01/09 INSTALLATION NOTES: Unpack your unit carefully
More informationDouble Swing Door With Header QCI5114
Double Swing Door With Header QCI5114 QCI5114 REV. 0 Page 1 of 9 Certified 06/22/2016 MAINTENANCE: Two primary materials are used to manufacture your new shower enclosure: tempered glass and anodized aluminum.
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More informationSLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 90º PANEL
SLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 0º PANEL This instruction sheet applies to the following units. C, C7, C7, C77, C, C7 This instruction sheet also applies to the following units. VTE / VSE
More informationSERIES: CONFIGURATION: MOUNTING PACKAGE: 1200 Door-Door Frameless, sliding door
SERIES: CONFIGURATION: MOUNTING PACKAGE: 1200 Door-Door Frameless, sliding door RDQCI5022 Rev.0 Page 1 Certified 06/01/2016 Tools: To install your New Shower Enclosure, you may need the following: Pencil
More information3/8 FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS 3/8 FRAMELESS BYPASS SLIDING SHOWER ENCLOSURE QCI-5017 QCI5017 Rev. 3 Page 1 of 9 Certified 12/6/17 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage.
More informationUNIT No. 15 & 16 SHOWER DOOR INSTALLATION INSTRUCTIONS
UNIT No. 15 & 16 SHOWER DOOR INSTALLATION INSTRUCTIONS Page 2 of 7 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure; tempered glass and anodized aluminum. To assure a
More informationK ARICA ROUND SHOWER ENCLOSURE
K-7050 ARICA ROUND SHOWER ENCLOSURE 1. BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation
More informationGLASSCRAFTERS, INC 193 Veterans Blvd., Carlstadt, NJ Frameless Sliding Door with Fixed Panel Shower/Tub Enclosure Installation Instructions
GLASSCRAFTERS, INC 193 Veterans Blvd., Carlstadt, NJ 07072 1+(888) 683-1362 -- (Fax) 201-525-1117 sales@glasscraftersinc.com MATRIX series Frameless Sliding Door with Fixed Panel Shower/Tub Enclosure Installation
More informationINSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232
INSTALLATION INSTRUCTIONS FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5232 QCI5232 Rev 0 Page 1 Certified 06/20/2016 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay
More informationFrameless Bypass Slider
INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 3/8 or 1/4 Glass Bypass Slider with Exposed Rollers QCI5301 Rev 1 Page 1 Certified 6/5/2017 Tools: To install your New Shower Enclosure, you may
More information1/4 FRAMELESS SLIDING DOOR FOR TUB OR SHOWER
1/4 FRAMELESS SLIDING DOOR FOR OR SHOWER INSTALLATION INSTRUCTIONS NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) M onda y - Friday 8 :00 A.M. - 4:30 P.M. Eastern Time MAINTENANCE: Two primary
More informationModel 2400/4000 Illustrated Installation Instructions
Model 2400/4000 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MNUFCTURERS 26121 venue Hall Valencia, C 955 (661) 257-77 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 293-6677
More informationM-PD93X INSTRUCTION MANUAL M
M-PD93X INSTRUCTION MANUAL 06.10 M003 Dimensions from wall to center of threshold MODEL FRONT (DIM A) SIDE (DIM B) MIN MAX MIN MAX 4836 45 7/8 46 3/8 33 7/8 34 3/8 6036 57 7/8 58 3/8 33 7/8 34 3/8 4832
More informationFIXED SHOWER SCREEN For Wall Mount Hinges QCI5283
FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL
More information1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A
1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE 1400A-1700A-1800A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More information640S & 650S SERIES FRAMED BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS Tel: 800-643-1514 www.alumaxshowerdoor.com 640S & 650S SERIES FRAMED BYPASS BATH ENCLOSURES Page 1 of 8 G03915346 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath Enclosures by
More informationInstallation Instructions
Arizona Corporate Office 2801 W. Indian School Rd Phoenix, AZ 85017 800 255 1901 PH 602 447 8208 FAX Florida 8100 1 Westside Industrial Dr Jacksonville, FL 32219 855 695 8899 PH 904 786 9025 FAX Illinois
More information340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More informationFRAMED PANEL / DOOR / PANEL CONTINUOUS HINGE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS
FRAMED / DOOR / CONTINUOUS HINGE SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS QCI5229 Rev 0 6 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts
More informationK-KR4Z - Kona INSTRUCTION MANUAL KK002
K-KR4Z - Kona INSTRUCTION MANUAL 07.10 KK002 Please keep this manual and product code number for future reference and replacement parts ordering if necessary. CURVED GLASS SLIDING SHOWER DOOR CURVED GLASS
More informationtile redi redi DOOR Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE:
redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Redi Swing Slide g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 3000 Door-Door Header, sliding doors RDQCI5301
More information1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE
1/4 FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE QCI5028 Rev 1 Page 1 Certified 09/19/2018 INSTALLATION NOTES: Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using
More informationFrameless Fixed Panel Slider QCI5279
Frameless Fixed Panel Slider QCI5279 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com Frameless Fixed Panel
More informationFrameless Bypass Slider
INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need
More informationWC INSTRUCTION MANUAL 2 PEOPLE REQUIRED SHOWER DOOR KW002
WC-66-75 INSTRUCTION MANUAL SHOWER DOOR 05.11 2 PEOPLE REQUIRED KW002 IT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS. GENERAL INSTRUCTIONS
More informationTools you will need for this install
Arizona Corporate Office 2801 W. Indian School Rd Phoenix, AZ 85017 800-255-1901 PH 602-447-8208 FAX Florida 8100-1 Westside Industrial Dr Jacksonville, FL 32219 855-695-8899 PH 904-786-9025 FAX Illinois
More information640D & 650D SERIES FRAMED BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 640D & 650D SERIES FRAMED BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Page 1 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath Enclosures by Sapa are intended to
More informationFrameless Fixed Panel Slider
INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need
More informationContinuous Hinge Frameless Single Swing Shower Enclosure QCI-5214
INSTALLATION INSTRUCTIONS Continuous Hinge Frameless Single Swing Shower Enclosure QCI-5214 QCI5214 Rev. 1 Page 1 of 8 Certified 09/19/18 MAINTENANCE: Two primary materials are used to manufacture your
More information340D / 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340D / 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2016. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More information1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE
INSTALLATION INSTRUCTIONS 1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More informationINSTALLATION INSTRUCTIONS. UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS UNIT No. 160/760 THIN-LINE SHOWER ENCLOSURE QCI0011 Rev. 0 Page 1of 10 Certified 10/18/2006 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure;
More informationUnit No. 135, 735 Deluxe Pivot Inline Door & Panel Shower Enclosure
INSTALLATION INSTRUCTIONS Unit No. 135, 735 Deluxe Pivot Inline Door & Panel Shower Enclosure NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0004
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Shower Height Swing Door Model: L533 Rev. 09.03.13 MAINTENANCE: Two primary materials are used to manufacture your new Aquatic enclosure; tempered glass
More information463-GP. Swing Door. Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) (Toll Free) 463-GP 5/06
463-GP Swing Technical ssistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 (Toll Free) PRTS LIST FRME PCKGE KEY DESCRIPTION PRT QTY SILL 855 1 JM 942 2 E MGNETIC
More informationFramed Single Swing Shower Enclosure Steam Continuous Hinge
INSTALLATION INSTRUCTIONS Framed Single Swing Shower Enclosure Steam Continuous Hinge QCI-5111 NEED INS TA LLA TIO N HELP? Cal l 1-800-45-BAS C O (452-2726 ) M on da y - Fr iday 8 :00 A.M. - 4:30 PM..
More information1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A
1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More information340 & 350 SERIES BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340 & 350 SERIES BATH ENCLOSURES 800-643-1514 www.alumaxbath.com Copyright Alumax Bath Enclosures 2010. All rights reserved. LIMITED WARRANTY AND REMEDY ALUMAX BATH ENCLOSURES
More information846-GP. Neo-Angle Enclosure. Technical Assistance is available Monday - Friday 8:00 a.m. - 5:00 p.m. (Central Time) GP 12/05
846-GP Neo-ngle Enclosure Technical ssistance is available Monday - Friday 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 PRTS LIST FRME PCKGE KEY ESCRIPTION PRT QTY SILL 855 3 M 942 2 C HEER 101
More informationUnit No. 135, 735 Deluxe Pivot Inline Door & Panel Shower Enclosure
INSTALLATION INSTRUCTIONS Unit No. 135, 735 Deluxe Pivot Inline Door & Panel Shower Enclosure NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0004
More informationUNIT No. 135/735 THIN-LINE SHOWER ENCLOSURE
INSTALLATION INSTRUCTIONS UNIT No. 135/735 THIN-LINE SHOWER ENCLOSURE QCI0004 REV. 1 Page 1 of 10 1-800 NE INSTA ED LLATI HELP ON? C -45-B all ASCO (452Mon 2726 8:00 day - Frida ) A.M. y Easte - 4:30 P.M.
More informationDeluxe Continuous Hinge Framed Door & Inline Panel with Return Panel Shower Enclosure
INSTALLATION INSTRUCTIONS Deluxe Continuous Hinge Framed Door & Inline Panel with Return Panel Shower Enclosure QCI0235 Page 1 of 11 Certified 08/20/10 MAINTENANCE: Two primary materials are used to manufacture
More information340 & 350 SERIES DELUXE FRAMELESS BYPASS
BATH ENCLOSURES An Alcoa Company Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com INSTALLATION INSTRUCTIONS 340 & 350 SERIES DELUXE FRAMELESS BYPASS BATH ENCLOSURES Copyright Alumax Bath Enclosures
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUTIONS BUILDERS HOIE FRAMED Shower Height Neo Angle Swing Door Model: L061 Rev. 09.20.13 MAINTENANE: Two primary materials are used to manufacture your new Aquatic enclosure: tempered
More informationP-DRC1Y OWNER S MANUAL
P-DRCY OWNER S MANUAL SHOWER ENCLOSURES PEOPLE REQUIRED 0.0 IT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS. P009 TABLE PANNEAU OF CONTENTS
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationFrameless Inline Door QCI5248
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar
More informationUnit No. 1400, 1700, 1800 Infinity Continuous Hinge Frameless Swing Door Shower Enclosure
INSTALLATION INSTRUCTIONS Unit No. 1400, 1700, 1800 Infinity Continuous Hinge Frameless Swing Door Shower Enclosure QCI0028 Rev. 2 Page 1 of 10 Certified 06/05/09 MAINTENANCE: Two primary materials are
More informationFIXED PANEL SLIDER QCI5241
INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page
More information935 RODA VINESSE NEED INSTALLATION HELP? DOUBLE ROLLERS FRAMELESS DOOR INSTALLATION INSTRUCTIONS QCI XX/XX/XXXX. Call BASCO ( )
INSTALLATION INSTRUCTIONS 935 RODA DOUBLE ROLLERS FRAMELESS DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday VINESSE QCI0286 1 XX/XX/XXXX 935 Roda Parts List With double rollers
More informationINSTALLATION INSTRUCTIONS. Unit No. 126, 726 Classic Pivot Panel/Door/Panel Shower Enclosure
INSTALLATION INSTRUCTIONS Unit No. 126, 726 Classic Pivot Panel/Door/Panel Shower Enclosure QCI0027 Rev. 0 Page 1 of 10 Certified 11/07/2006 MAINTENANCE: Two primary materials are used to manufacture your
More informationProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE
INSTALLATION INSTRUCTIONS ProLine PL60 HEAVY FRAMELESS BYPASS BATH ENCLOSURE Copyright Alumax Bath Enclosures 2013. All rights reserved. G03980847 5-1-13 !WARNINGS! INSTALLATION WARNINGS a) Alumax Bath
More informationINSTALLATION INSTRUCTIONS FIXED PANEL SLIDER FRAMELESS DOOR / PANEL. QCI0280 Page 1 Cer fied 6/27/14
INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER FRAMELESS DOOR / PANEL QCI0280 Page 1 Cer fied 6/27/14 VINA-935 Parts List ITEM NO. 1 2 NUMBER DESCRIPTION QTY. CLZ2278-13A (44"-47") CLZ2878-13A (56"-59")
More informationUnit No. 1413NP, 1713NP, 1813NP Infinity Continuous Hinge Frameless Door & Inline Panel with No Post Shower Enclosure
INSTALLATION INSTRUCTIONS Unit No. 1413NP, 1713NP, 1813NP Infinity Continuous Hinge Frameless Door & Inline Panel with No Post Shower Enclosure QCI0239 Page 1 of 12 Certified 8/2/10 MAINTENANCE: Two primary
More informationUNIT No. 1415NP / 1715NP / 1815NP INFINITY FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE WITH NO INLINE POST
INSTALLATION INSTRUCTIONS UNIT No. 1415NP / 1715NP / 1815NP INFINITY FRAMELESS CONTINUOUS HINGE SHOWER ENCLOSURE WITH NO INLINE POST QCI0240 Page 1 of 13 Certified 8/2/10 INSTALLATION NOTES: Unpack your
More information713C-GP. Pivot Door. Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) (Toll Free) 713C-GP 8/06
713C-P Door Technical Assistance is available Monday - Friday, 8:00 a.m. - 5:00 p.m. (Central Time) 1-877-723-7190 (Toll Free) PARTS IST FRAME PACKAE KEY DESCRIPTION PART QTY A SI A195 1 PIVOT JAM A196
More informationFrameless Inline Door QCI5254
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5254 FRAMELESS DOOR / PANEL QCI5254 REV. 0 Page 1 Cer fied 06/16/2016 Parts List with wall mount hinges *Quanes may vary QCI5254 REV. 0 Page 2 Cer fied
More informationModel 5400H / 7000H Illustrated Installation Instructions
Model 5400H / 7000H Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 261 Avenue Hall Valencia, CA 91355 (661) 257-1177 (661) 257-4907 TOLL FREE: (800) CW-DOORS (800) 293-6677
More informationFrameless Inline Door QCI5250
INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2
More informationFRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274
FRAMELESS DOOR / PANEL WITH WALL MOUNT HINGES QCI5274 QCI0274 QCI5274 REV. Rev. 1 0 Page Page 1 1 Date Certified: Certified 06/16/2016 10/01/10 Parts List with wall mount hinges ITEM NO. Part # DESCRIPTION
More informationFrameless Inline Door QCI5288
Frameless Inline Door QCI5288 QCI5288 Rev. 0 Page 1 Date Certified: 06/21/2016 Tools: To install your New Shower Enclosure, you may need the following: Pencil Drill Hack Saw Low Tack Tape 1/8 & 3/16 Drill
More information738 SERIES PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS 738 SERIES PIVOT SHOWER DOOR Copyright Alumax Bath Enclosures 1997. All rights reserved. Page 1 of 8 LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers,
More informationSTEAM TIGHT. Installation Instructions 200S/250S. SCFMDPP Parts Pak Includes: Letters C,D,E,J,S,V,W,X,Y,BB,CC,DD
STEAM TIGHT Installation Instructions 200S/250S SCFMDPP Parts Pak Includes: Letters C,D,E,J,S,V,W,X,Y,BB,CC,DD Fillers for out of plumb conditions SC553* for walls (vertical). SC543* for threshold (horizontal).
More informationQCI0029 REV. 1 Page 1 of 11 Certified 07/06/05
QCI0029 REV. 1 Page 1 of 11 Certified 07/06/05 MAINTENANCE: Two primary materials are used to manufacture your new Basco enclosure: tempered glass and anodized aluminum. To assure a long lasting finish
More informationFRAMELESS FIXED PANEL SLIDER with 90 RETURN
INSTALLATION INSTRUCTIONS FRAMELESS FIXED PANEL NE INSTA ED LLATI SLIDER with 90 RETURN HELP ON? QCI-5151 QCI5151 REV. 1 Page 1 of 14 1-800 C -45-B all ASCO (452Mon 2726 8:00 day - Frida ) A.M. y Easte
More informationA-935 RODA WALL MOUNT HINGES
INSTALLATION INSTRUCTIONS A-935 RODA WALL MOUNT HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time FRAMELESS DOOR / PANEL CELESTA QCI0274 REV.
More informationProLine PL60 - PL70 - PL80 RETURN PANEL SUPPLEMENT
INSTALLATION INSTRUCTIONS ProLine PL60 - PL70 - PL80 RETURN PANEL SUPPLEMENT Copyright Alumax Bath Enclosures 2013. All rights reserved. G03000000 7-1-13 Three-Year Limited Residential Warranty Alumax
More informationPage 1. FIG. #1 - Shower Door Assembly SHOWER & BATH ENCLOSURES BUILT TO LAST A LIFETIME HANDLE ASSEMBLIES REMOVED FOR CLARITY.
FIG. #1 - Shower Door Assembly 29 1 2 1 6 9 9 5 HANDLE ASSEMBLIES REMOVED FOR CLARITY. 25 25 PLEASE REFER TO FIG. #2 FOR INSTALLATION 26 12 17 18 18 17 10 3 11 7 10 8 Page 1 FIG. #2 - Top View 5 21 10
More informationP-DR1W-48 P-DR1W-60 OWNER S MANUAL
P-DRW-48 P-DRW-0 OWNER S MANUAL SHOWER ENCLOSURES PEOPLE REQUIRED IT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS. P00 0.0 TABLE PANNEAU OF
More informationFrameless Heavy Glass Door with Header
INSTALLATION INSTRUCTIONS Frameless Heavy Glass Door with Header QCI5243 QCI5243 REV. 0 Page 1 Certified 06/16/16 Frameless Heavy Glass Door with Pivot Hinges ITEM NUMBER DESCRIPTION QUANTITY 1 DOOR GLASS
More informationFrameless Door QCI5284
Frameless Door QCI5284 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com INSTALLATION INSTRUCTIONS Frameless
More informationDouble Frameless Swing Door QCI5247
INSTALLATION INSTRUCTIONS Double Frameless Swing Door QCI5247 WALL MOUNT HINGES QCI5247 REV. 0 Page 1 Certified 06/16/2016 Parts List with wall mount hinges *Quantities may vary **Quantities double where
More informationINSTALLATION INSTRUCTIONS 960 RODA GLASS TO GLASS HINGES ANGLED FRAMELESS PANEL / DOOR / PANEL CELESTA DRESDEN TRESOR
INSTALLATION INSTRUCTIONS 960 RODA GLASS TO GLASS HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time ANGLED FRAMELESS PANEL / DOOR / PANEL
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationFrameless Heavy Glass Door with Wall Mount Hinges
INSTALLATION INSTRUCTIONS Frameless Heavy Glass Door with Wall Mount Hinges QCI-5245 QCI5245 REV. 0 Page 1 Certified 06/16/16 Frameless Door with Wall Mount Hinges ITEM NUMBER DESCRIPTION QUANTITY 1 DOOR
More information300C6 CONTINUOUS HINGE SEMI-FRAMELESS DOOR KIT
300C6 CONTINUOUS HINGE SEMI-FRAMELESS DOOR KIT LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers, customers, and all subsequent purchasers and users, that the products supplied
More informationINSTALLATION INSTRUCTIONS 935 RODA GLASS TO GLASS HINGES FRAMELESS DOOR / PANEL CELESTA DRESDEN GEOLUX TRESOR VONSE
INSTALLATION INSTRUCTIONS 935 RODA GLASS TO GLASS HINGES NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time FRAMELESS DOOR / PANEL CELESTA DRESDEN
More informationInstallation Instructions
Installation Instructions Alcove Enclosure Before Installation please check that your shower enclosure system is undamaged Please read these instructions carefully March 2015 TOOLS REQUIRED Electric or
More informationENCORE / BRAVO SHOWER AND TUB DOOR INSTALLATION NSTRUCTIONS
ENCORE / BRAVO T F e s a SHOWER AND TUB DOOR INSTALLATION I NSTRUCTIONS le A R re r fo IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For
More informationESSENCE. Shower / Tub Door Installaion Instructions
ESSENCE Shower / Tub Door Installaion Instructions IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest up-to-date technical drawings,
More informationtile redi redi DOOR Redi Swing SERIES: CONFIGURATION: MOUNTING PACKAGE:
redi DOOR INSTALLATION INSTRUCTIONS tile redi Redi Swing g TM TM...Opening Doors to Stunning Showers! TM TM SERIES: CONFIGURATION: MOUNTING PACKAGE: 2900V Door-Panel No header, offset pivot hinges, u-channel
More information