BIG MAX 7' x 3'6" RESIN STORAGE BUILDING ASSEMBLY. Two Person Assembly D X K U

Transcription

1 P N D X E G Q F J H K U 95" Description ssembly Letter Quantity Left Floor Left Side Panel ight Side Panel D Left Back Panel E ight Door Panel F ight Back Panel G Left Front Panel H ight Front Panel J Left Door Panel K Gable Left oof Panel N ight oof Panel P Wall onnector Q 4 idge Beam ight Floor U Lock Hasp X #4 x.0" ombo Pan Head Screw 4 /4-0 x 0.5" ombo ound Head Bolt BB /4-0 Flat Washer /4-Hex Nut DD oof Pin EE 4 equired Tools Safety Glasses ubber allet Phillips Screw Driver Liquid Soap () Step Stools/Stepladders 7 84 /8" BIG X 7' x '6" ESIN STOGE BUILDING SSEBLY Pre-ssembly: eview the parts list and make sure that no parts are missing. Level the area where the shed will be located. reas of fill dirt should be tamped/compacted to prevent settling/sinking. Ifafoundation is desired, it should be constructed before assembly. NOTE: To simplify assembly and to ensure proper engagement of all components, apply a mild detergent to dovetail and snap fits before assembling. Two Person ssembly 4 /8"

2 Level construcion site before beginning assembly of shed. foundation may be constructed if desired. onnect Left Floor () to ight Floor (U), install Screws () 4 places. (4) U 4 /8" 84 /8" OPTIONL STEP: If desired, recessed anchor locations (4 places) can be used to anchor the shed floor to a foundation. aution: When installing screws do not overtighten. Using a srewdriver, punch out the screw holes on the top of Left Side Panel () Places. onnect Left Side Panel () into Left Floor (). Screw Holes 4 /8" 76" 4 /8" 5 /4" 5 /4" 0 /8" 4 /8" 7 /" 7 /" 4 /8" 4 /8" 84 /8"

3 4 Lubricate dovetails on Left Front Panel (H) 4 places with liquid soap. onnect Left Front Panel (H) into dovetails of Left Side Panel (), engage snaps on bottom of Left Front Panel (H) into Left Floor (). 5 Lubricate dovetails on Left Back Panel (E) 4 places with liquid soap. onnect Left Back Panel (E) into dovetails of Left Side Panel (), engage snaps on bottom of Left Back Panel (E) into Left Floor (). E H 6 epeat Steps 5 to assemble right side of shed. ontinue to Step 7. 7 Engage lap joint between Left Back Panel (E) and ight Back Panel (G) and install Wall onnectors (Q) 4 places. E G See Step 5 See Step See Step 4 Q G D J E G

4 8 Install Gable () onto top of back wall engaging the dovetails and snaps on the back panel and the dovetail on the side panel on both the left and right sides of the shed. 9 Install Gable () onto top of front wall engaging the dovetails on the front panel and the dovetail on the side panel on both the left and right sides of the shed. DO NOT ENGGE THE SNPS. 0 Install Left Door Panel (K) inserting the lower hinge pin into Left Floor () socket, lift the left end of the Gable () enough to insert the top hinge pin on Left Door Panel (K) into the Gable () socket. Install ight Door Panel (F) inserting the lower hinge pin into ight Floor (U) socket, lift the right end of the Gable () enough to insert the top hinge pin on ight Door Panel (F) into the Gable () socket. Install Lock Hasp (X) into back side of ight Door Panel (F). Engage Gable () snaps on front wall. 4 4 F K U X

5 Place idge Beam () into cups at the top of each Gable (). lign slots in idge Beam () with holes in Gable () tabs, install Bolt (BB), Washer (), and Nut (DD) place, ONLY TIGHTEN NUT FINGE TIGHT. Washer Nut Plastic Tab on Gable Bolt Head DD BB 4 lign slots in idge Beam () with holes in Gable () tabs, install Bolt (BB), Washer (), and Nut (DD) place, ONLY TIGHTEN NUT FINGE TIGHT. 5 Lubricate roof snaps on Gable () 8 places on each Gable (). aise the Left oof Panel (N) onto the left side of the shed assembly, the arrows on the roof panel should face the inside of the shed and point towards the idge Beam (). Washer Nut Plastic Tab on Gable Bolt Head N DD BB

6 6 Using () step stools ( inside shed, outside shed), lift the bottom of the roof panel above horizontal, guide the roof panel into the idge Beam (), align both Gable () ribs with the channels in Left oof Panel (N), engage Left oof Panel (N) in idge Beam () by lowering the bottom of the roof panel onto the shed assembly (hold idge Beam() to prevent twisting). N N hannel oof Panel ib Gable ib 7 Engage all snaps between the roof panel and gable, then roof panel and wall panel. 8 epeat Steps 5 7 for right roof of shed. P N See Steps 5 7 P Back of shed shown

7 9 Install Screws () 6 places in Gable (). 0 While one person holds down the bottom of the roof, install screws () 4 places in screw holes on the top of the Side Panels (&D). Screws connect the Side Panels to the oof Panels. (6) (4) aution: When installing screws do not overtighten. Install oof Pins (EE) 4 places connecting the oof Panels to the Gables. aution: When installing screws do not overtighten. EE (4)

8 OPTIONL STEP: If desired, add wood to create a loft (wood not included)..75" x 4" x 7.75".75" x 7.5" x 7.75".75" x 4" x 7.75" 95" 84 /8" 4 /8" Printed in U.S.. Imprimé aux Ètats-Unis. Impreso en los EE.UU. 00 ubbermaid Home Products, Wooster, OH, U.S ustomer Service Toll Free: F 8 to 5P EST or visit us at OS