Appliance Pulls. Cabinet Furniture CF2:010

Transcription

1 A selection of Pulls available in a variety of sizes to complement both traditional and modern interiors. They can also be found in the oor Furniture section (see F3) where most are available fitted to back plates and many are offered in pairs for back-to-back installation. offset design, RH shown offset design AA & 1433A supplied with finish matched no.6 x 19mm wood screws and M6 x 50mm machine screws (longer screws available upon request). 1433B & 1433 supplied as above, but with finish matched no.8 x 25mm wood screws. 1435AA & 1435A supplied with finish matched no.6 x 19mm wood screws. 1435B & 1435 supplied with finish matched no.8 x 25mm wood screws. 1434, 3934, 6999, 9512 & 9531 supplied with M6 x 50mm machine screws (longer screws available upon request). offset design 4325 supplied with M8 x 50mm machine screws (longer screws available upon request) offset design ) select HANLE (e.g. 1435) 2) add FINISH (e.g. 1435PB) 3) add SIZE, except 3934 & 9531 (e.g. 1435PB/) only - add HANING (e.g. 9531P/LH). Overall length entres Proj A B A B Overall length entres Proj 9512 A B AA A B (face fixed only) 1433 (face fixed & rear bolt fixing) F2:010

2 A classic Pull, available in three lengths and with twelve Rosette designs, each in up to three diameters, to complement the Allart Select oor Knob & Lever Rosettes (see section ST3) and the abinet Knobs shown on pages F1:060 & These Pulls can also be found in the oor Furniture section (see F3) available fitted to back plates and offered in pairs for back-to-back installation Supplied with M8 x 50mm machine screws (longer screws available upon request) ) select HANLE (e.g. 4358) 2) add FINISH (e.g. 4358P) 3) add LENGTH (e.g. 4358P/A) 4) add ROSETTE SIZE (e.g. 4358P/A38) size B Pull shown with 54mm Ø rosettes 4360 (centres) Projection (diameter) A Ø 38 B Ø 44, 54, Ø 44, 54, 64 F2:020

3 A traditional Pull, available in two lengths and with eight Rosette designs, each in four diameters, to complement the Allart Select oor Knob & Lever Rosettes (see section ST3) and the abinet Knobs shown on pages F1:060 & These Pulls can also be found in the oor Furniture section (see F3) available fitted to back plates and offered in pairs for back-to-back installation Supplied with M6 x 50mm machine screws (longer screws available upon request). 1) select HANLE (e.g. 1911) 2) add FINISH (e.g. 1911P) 3) add LENGTH (e.g. 1911P/A) 4) add ROSETTE SIZE (e.g. 1911P/A44). size A Pull shown with 54mm Ø rosettes (centres) Projection (diameter) A Ø 38, 44, 54, 64 B Ø 38, 44, 54, 64 F2:030

4 A traditional offset design Pull, available in two lengths and with eight Rosette designs, each in four diameters, to complement the Allart Select oor Knob & Lever Rosettes (see section ST3) and the abinet Knobs shown on pages F1:060 & These Pulls can also be found in the oor Furniture section (see F3) available fitted to back plates and offered in pairs for back-to-back installation Supplied with M6 x 50mm machine screws (longer screws available upon request). 1) select HANLE (e.g. 1986) 2) add FINISH (e.g. 1986P) 3) add LENGTH (e.g. 1986P/A) 4) add ROSETTE SIZE (e.g. 1986P/A44) size A Pull shown with 44mm Ø rosettes (centres) Projection (diameter) A Ø 38, 44, 54, 64 B Ø 38, 44, 54, 64 F2:040

5 Bakes Pulls and Bakes Knobs lassic Robert Bakes designed Pulls & abinet Knobs. The Pulls are available in five sizes from 130mm up to 375mm, whilst the Knobs are offered in two sizes. E B A 0660 P 0660A- supplied with M4 x 50mm break-off machine screws (longer screws available upon request). 0660E supplied with M8 x 50mm machine screws (longer screws available upon request) supplied with M4 x 50mm break-off machine screws. L 0660 A B E L (length) (centres) P (projection) owel Screw option available 0660 Pulls: H 1) add FINISH (e.g. 0660P) 2) add SIZE (e.g. 0660P/A) 0661 Knobs: 1) add FINISH (e.g. 0661P) 2) add SIZE (e.g. 0661P/B) hoose OWEL SREW option if required (e.g. 0661P/B/S). size B size A P W 0661 A B H x W (height x width) 33 x x 53 P (projection) F2:050

6 abinet Pulls An Art eco design offset abinet Pull available in three different guises to complement the 9512 Appliance Pulls shown on page F2:010 and the abinet Knobs shown on page F1:040. approx actual size 9502 approx actual size & 9503 supplied with M4 x 50mm break-off machine screws supplied with finish matched no.6 x 19mm wood screws. 1) select HANLE (e.g. 9503) 2) add FINISH (e.g. 9503P). approx actual size F2:060