Needed material : Check the place where the staircase will be installed. Is the adjoining wall completely fl at? Is the fl oor fl at?
|
|
- Bertram Bruce
- 5 years ago
- Views:
Transcription
1 Concorde Needed material : SDS drill Ø12mm, length 20cm Levelling staff ± 70 cm Meter Big try square Wrench for stainless steel threaded rods n 10 Wrench for hexagon socket countersunk head cap screws Grey silicone Double sided rubber UPAT UPM 44 chemical mortar and pistol General purpose thread sealant Situation Check the place where the staircase will be installed. Is the adjoining wall completely fl at? Is the fl oor fl at? Adjust if necessary so that the staircase can be installed straight and on level! Release the 4 bolts on the side of the uppertread. Put the tread to the fl oor and beware of future fi nished fl oor. 1 Description Concorde is an aluminium staircase made out of 2 massive fl at stringers with integrated airplane formed steps. Very slim on the frontside, monumentally rounded on the backside. Made to measure in respect of width, length and angle of inclination. Anodised aluminium is used for a nicely fi nished natural product. The airy character of the staircase is accentuated by the thin beams. Square up wall and tread! evolis 100 B-8500 kortrijk info@graah.be TEL Put the tread on level in length and width (completely fl at with fl oor). 2 Foresee suffi cient space to fi x balustrade. To keep the tread on its spot, fi x it temporarily with plug and screw. 3
2 Drill approximately 5 holes Ø12mm on different heights and 18cm deep in the wall. Clean carefully before using chemical mortar. Beware of wires of electricity or fl oor heating. For wooden fl oor, use wood screws. Fixation staircase Fill the holes with chemical mortar. Put the threaded rods in the holes by rotation movement until they stick out 1,5cm. Let harden and remove the uppertread from the rods. The excess of mortar assures ideal installment when the staircase is hanged on the rods. Fixation covering plate Keep tread on its place! Fix the uppertread in the staircase by means of the 4 bolts and hang the staircase on the rods. Screw the bolts M10 on the rods and tighten them Finishing of staircase Fixation staircase If the staircase isn t supported by both beams, use a block of ± 4cm high under the supporting beam and twist the staircase until both beams are supporting. Fill up the opening with gray silicone. Lift the staircase and put a block underneath. Fix the doublesided rubber under the stringers. Clean up and degrease the fl oor under the staircase. Put down the staircase according to right distance from the wall
3 Triangle Needed material : SDS drill Ø12mm, length 20cm Levelling staff ± 70 cm Meter Big try square Wrench for stainless steel threaded rods n 10 Wrench for hexagon socket countersunk head cap screws Grey silicone Double sided rubber UPAT UPM 44 chemical mortar and pistol General purpose thread sealant Situation Check the place where the staircase will be installed. Is the adjoining wall completely fl at? Is the fl oor fl at? Adjust if necessary so that the staircase can be installed straight and on level! Put the tread on level! Put the tread on level in length and width (completely fl at with fl oor). Check the distance between the tread and the wall. 1 Description Aluminium staircase made of 2 centered massive stringers on which the steps are secured b a dentated profi le. The Triangle is measure made in respect of width, length and angle of inclination. Anodised aluminium is used for a nicely fi nished natural product. The Triangle is different because the steps are put on the stringers instead of in between. Keep the tread on its place! evolis 100 B-8500 kortrijk info@graah.be TEL Square up the adjoining wall and the uppertread. Drill ± 5 holes Ø12mm on different heights and 18cm deep in the wall. Fix the staircase with wood screws if wooden fl oor. 2 Clean carefully before using chemical mortar. To keep the tread on its spot, fi t it temporarily with plug and screw. 3
4 Put the threaded rods in the holes by rotation movement until they stick out 1,5cm. Let harden and remove the uppertread from the rods. The excess of mortar assures ideal installment when the staircase is hanged on the rods. Fix the covering side plates on the uppertread. Fixation steps Difference left and right coverplate! Check fi xing points! Fix all steps for down to up. In case of balustrade on the staircase, the second step has 2 holes M6 down on the corner. Pay attention to fi x steps according to balustrade. Tighten bolts now. Fixation stringers Screw the bolts M10 on the rods and tighten them. Put the 2 stringers in the uppertread by means of the threaded rods M10 and the round headed screw nuts, don t tighten up because the stringers need to be positioned. Measure the distance from stringer to wall so that stringers are parallel. Fixation covering plate Protect the fl oor beneath the stringers! Tighten up the round headed screw nuts. Glue and fi x the side coverings of the steps. Finishing of staircase Fixation steps Degrease the upside of the stringers. Spray some transparant silicone glue around the drilling holes. Fix the fi rst step on the backside of the stringer with the M10 bolts and the wrench for hexagon screws Fill up the opening with gray silicone. Lift the staircase and put a block underneath. Fix the doublesided rubber under the stringers. Clean up and degrease the fl oor under the staircase. Put down the staircase according to right distance from the wall
5 Starlight Needed material : SDS drill Ø12mm, length 20cm Levelling staff ± 70 cm Meter Big try square Wrench for stainless steel threaded rods n 10 Wrench for hexagon socket countersunk head cap screws Grey silicone Double sided rubber UPAT UPM 44 chemical mortar and pistol General purpose thread sealant Situation Check the place where the staircase will be installed. Is the adjoining wall completely fl at? Is the fl oor fl at? Where is power supply provided? Adjust if necessary so that the staircase can be installed straight and on level! Release the 4 bolts on the side of the uppertread. Put the tread to the fl oor and beware eventually of future fi n- ished fl oor and the distance to the wall. 1 Description Aluminium stairway made of C shaped massive stringers with salient treads. The possibility to integrate different types of light in the stringers or on the steps characterizes the Starlight. The monumentality of the stringers is another obvious item. Made to measure in respect of width, length and angle of inclination. Square up wall and tread! evolis 100 B-8500 kortrijk info@graah.be TEL Put the tread on level in length and width (completely fl at with fl oor). 2 Provide suffi cient space to fi x balustrade. To keep the tread on its spot, fi x it temporarily with plug and screw. 3
6 Drill approximately 5 holes Ø12mm on different heights and 18cm deep in the wall. Clean carefully before using chemical mortar. Beware of wires of electricity or fl oor heating. For wooden fl oor, use wood screws. Fill the holes with chemical mortar. Put the threaded rods in the holes by rotation movement until they stick out 1,5cm. Let harden and remove the uppertread from the rods. The excess of mortar assures ideal installment when the staircase is hanged on the rods. Fix the uppertread in the staircase by means of the 4 bolts and hang the staircase on the rods. Screw the bolts M10 on the rods and tighten them. Fix the covering side plates on the uppertread. Keep tread on its place! Fixation staircase Difference left and right coverplates! Difference left and right coverplate! Fix the LED-or RGB LED-strip under the uppertread as shown. Make the connection with the RGB LED-strip under the uppertread as shown. Fill up the opening with gray silicone. 7 8 Lift the staircase and put a block underneath. Fix the doublesided rubber under the stringers. Clean up and degrease the fl oor under the staircase. Put down the staircase according to right distance to the wall. Slide the covering plates on the stringers and fi x the covering plates for the steps. 9
7 Situation no counterplate Check the place where the staircase will be installed. Is the adjoining wall completely flat? How thick and out of which material is the wall cosntructed? (minimum 14cm and no Ytong-bricks). Where is the power supply? Adapt eventually the environment. SDS drill Ø12mm, length 20cm Levelling staff ± 70 cm Meter Big try square Wrench for stainless steel threaded rods n 10 Wrench for hexagon socket countersunk head cap screws Grey silicone Double sided rubber UPAT UPM 44 chemical mortar and pistol General purpose thread sealant Positioning 1st stringer Solitaire Needed material : Fix the double sided rubber underneath the stringer. Position the first part of the stringer to the wall. Drill a hole up and down to fix stringer with plug and screw. Then drill the other holes in the wall. Remove dust before using chemical mortar. 1 Description evolis 100 B-8500 kortrijk info@graah.be TEL Fixation 2nd stringer The Solitaire is measure made in respect of width, length and angle of inclination. Fixation 1st stringer Anodised aluminium staircase with bar shaped treads, fixed on only 1 side to the stringer, and secured by a triangular inox support. Fill the holes with chemical mortar. Put the threaded rods in the holes by rotation movement until they stick out 1,5cm. Hook the second stringer into the first and fix with hexagon threaded rods. Tighten firmly the bolts. Degrease the gap between the first and second stringer and seal it by means of silicone. 2 3
8 Position the uppertread square and on level in length and width next to stringer (completely fl at with fl oor). Keep on right place by using a girder or by fi xing with 2 windowplugs. Drill holes of Ø12mm, 18cm deep. If wooden fl oor, use wood screws. Remove dust from holes and fi ll them with chemical mortar. Put the threaded rods in the holes by rotation movement. Let harden and tighten the bolts. Fix the treads using pin screwdriver M10. Attach the coveringplates of the treads and glue and slide the coverings on the bottom and side of the steps Fixation steps Fix the LED-or RGB LED-strip into the stringer. Make sure that electric current is under the uppertread or on top of the beam. Make the connection with the LED-strip under the uppertread as shown. Make the connection with the RGB LED-strip under the uppertread as shown. Stick the plexi covering plate by means of transparant glue, above and down the stringer. Fill up the opening with gray silicone Fix the covering plates with glue as necessary.
9 Situation with counterplate Check the place where the staircase will be installed. Is the adjoining wall completely flat? How thick and out of which material is the wall constructed? (less than 14 cm and no Ytong-bricks) Where is the power supply provided? Adapt eventually the environment. SDS drill Ø12mm, length 20cm Levelling staff ± 70 cm Meter Big try square Wrench for stainless steel threaded rods n 10 Wrench for hexagon socket countersunk head cap screws Grey silicone Double sided rubber UPAT UPM 44 chemical mortar and pistol General purpose thread sealant Positioning 1st stringer Solitaire Needed material : Fix the double sided rubber tape underneath the stringer. Position the 1st part of the stringer to the wall. Drill a hole up and down to fix the stringer with plug and screw. Then drill the other holes in the wall. Keep a plate against the backside of the wall to avoid crumbling of wall. 1 Description evolis 100 B-8500 kortrijk info@graah.be TEL Fixation 2nd stringer The Solitaire is measure made in respect of width, length and angle of inclination. Fixation 1st stringer Anodised aluminium staircase with bar shaped treads, fixed on only 1 side to the stringer, and secured by a triangular inox support. Remove the plaster around the holes on the backside of the wall and put the threaded rods in the holes after inserting chemical mortar. Or use a counterplate on the backside of the wall. Tighten firmly the bolts. 2 Hook the second stringer into the first and fix with hexagon threaded rods. Degrease the gap between the first and second stringer and seal it by means of silicone. 3
10 Position the uppertread square and on level in length and width next to stringer (completely fl at with fl oor). Keep on right place by using a girder or by fi xing with 2 windowplugs. Drill holes of Ø12mm, 18cm deep. If wooden fl oor, use wood screws. Remove dust from holes and fi ll them with chemical mortar. Put the threaded rods in the holes by rotation movement. Let harden and tighten the bolts. Fix the treads using pin screwdriver M10. Attach the coveringplates of the treads and glue and slide the coverings on the bottom and side of the steps Fixation steps Fix the LED-or RGB LED-strip into the stringer. Make sure that electric current is under the uppertread or on top of the beam. Make the connection with the LED-strip under the uppertread as shown. Make the connection with the RGB LED-strip under the uppertread as shown. Stick the plexi covering plate by means of transparant glue, above and down the stringer. Fill up the opening with gray silicone Fix the covering plates with glue as necessary.
Determine the proper ground fixing stair position, by using, as a reference, the landing tread [Fig. 7].
METAL SPIRAL STAIR MOUNTING INSTRUCTIONS - ENGLISH - PRELIMINARY OPERATIONS Prior to fitting your staircase, please check the packaging content. You then place all components onto a wide surface in order
More informationGraz. Flexible modular staircase
Attic ladders Space saving staircases Modular staircases Spiral staircases Graz Flexible modular staircase Main staircases Metal support Rise Treads Shape Banister Height Packaging Grey (RAL 9007) 18,5-22,5
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationHow To Build An. External Closed Staircase
How To Build An External Closed Staircase How To Build An External Staircase FOREWORD How to build a staircase explains the basic principles behind the construction and installation of external closed
More informationALLORA SWING PANEL INSTALLATION INSTRUCTIONS
ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:
More informationGlass Front Sauna Room Assembly Manual
Glass Front Sauna Room Assembly Manual Classic Bench Version: 1.3 Note: Above images are for illustrative reference only and may differ from actual item. Parts List Exterior *For room with full glass wall
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationInstallation Instructions. Walk-in Shower Screen. with 180 Return Panel
Installation Instructions Walk-in Shower Screen O with 180 Return Panel Installation Instructions Important Information Please read these instructions carefully before starting installation and keep for
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationPOOL ENCLOSURES LEIA & ALVA. Assembly manual
POOL ENCLOSURES LEIA & ALVA Assembly manual Rev. 07.2017 PARTS LIST Parts for rail installation: Rail Síncsavar screw 1 Plastic Síncsavar anchor 10 50 2 Rail Síncsavar connector 3 Arrest Síncsavar wedge
More informationStep by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com
Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from smith+noble. Your new window treatments have been
More informationInstallation Guide. Bi-fold Doors
Installation Guide Bi-fold Doors Installation Guide Components box 1. 6. 2. 3. 7. 5. 4. 8. Contents 1. Fixing plugs 2. Wedge gasket 3. Bottom trolley 4. Top trolley 5. Magnetic keep (x 2 if door height
More informationInstallation Guide Simplicity Alfresco. V1.9 Lu070318
0333 305 5272 www.canoports.co.uk Installation Guide Simplicity Alfresco V1.9 Lu070318 Tools Required Below is a list of tools that you will require to install your the Simplicity Alfresco System. Cordless
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More informationInstallation of HORIZONT and HORIZONT HIGH pool enclosures
Installation of HORIZONT and HORIZONT HIGH pool enclosures Rev. 19.10.2017 PARTS LIST Parts for rail installation: Rail screw 6 x 60 Plastic anchor 10 x 50 Rail connector Arrest wedge [R-L] Pop rivet 4
More informationENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH
ENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH RAFTER PREPERATION RAFTER PREPARATION A FRAME PREPERATION AND ASSEMBLY A FRAME PREPARATION AND ASSEMBLY... Open boxes, remove
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationInstallation Guide Contemporary Alfresco V1.3 LU
Installation Guide Contemporary Alfresco V1.3 LU 010818 Tools Required Below is a list of tools that you will require to install you're the Contemporary Alfresco System. Cordless Drill Mastic Gun Spirit
More informationMOTORIZED STANDARD SHADE WITH CABLES Installation Instructions
Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench
More informationHeavy Duty I-Beam Trolley
Heavy Duty I-Beam Trolley ASSEMBLY INSTRUCTIONS I-BEAM TROLLEY Recommended Tools Level Tape Measure Pencil Drill with 1/8, 1/4, and 3/8, Drill Bits and Phillips Bit Socket Wrench with 9/16 Socket I-BEAM
More informationParts & Tools. O'Cello printing and assembly instructions. o-cello.com
The O'Cello is a 3D-printable cello developed by Conor O'Kane, which is free to download and print for personal use. This document will show you how to print and assemble your own O'Cello. For the latest
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COMPACT LAMINATE TOILET PARTITIONS 1080 DuraLineSeries 1180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information
More informationaluminium profile system
aluminium profile system 63 AME System aluminium profiles overview series profiles introduction 80x80 x80 x80/180 x Aluminium profiles are provided with longitudinal grooves which can be used in conjunction
More informationMANUAL MOUNTING SYSTEM FOR CORRUGATED ROOF
MANUAL MOUNTING SYSTEM FOR CORRUGATED ROOF EN mounting system for corrugated roof for solar panels in portait setup (cross-system) ESDEC BV 2015 TABLE OF CONTENT 1. Introduction 1 2. General installation
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION Soild Phenolic Series contents page 1080 DuraLineSeries...2-21 1180 DuraLineSeries...2-21 2080 DuraLineSeries Maximum Privacy...22-41 2180 DuraLineSeries Maximum Privacy...22-41
More informationMelamine Plastic Laminate. Toilet Partition Installation Manual
Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE
More informationM4 Foot Operated Underpinner Instruction Manual
M4 Foot Operated Underpinner Instruction Manual M4 Walker Rd, Bardon Hill, Coalville, Leicestershire LE67 1TU, England Tel. +44 (0)130 1692, Fax +44 (0)130 16929 e mail sales@framerscorner.co.uk M4 Underpinner
More informationP a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s
P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s Before You Begin: Professional installation by two-person crew is required for this fixture. Install water supply and drain piping
More informationTeacherGeek Launcher Example Build
LAUNCHER EXAMPLE BUILD TeacherGeek Launcher Example Build TeacherGeek, 2011 LAUNCHER EXAMPLE BUILD TeacherGeek 2 LAUNCHER BASE PARTS A B D F E C G LAUNCHER EXAMPLE BUILD TeacherGeek 3 ASSEMBLING THE LAUNCHER
More informationInstallation Instructions
Column & Beam Units with Debris Netting Installation Instructions Laminated Wood Systems, Inc. Seward, Nebraska 800-949-3526 2015 LWS, INC. AVR-NET INSTALL 05-12-16 AVR Installation Notes 1 Safety The
More informationOriginal Gallery System
GAllery System Art Displays Original Gallery System a Gallery System product Here s everything you need to know to get started with your Gallery System Art Hanging System GS getting started To install
More informationStep-by-Step Installation Instructions for
Step-by-Step Installation Instructions for Customer helpline number: 01604 633607 8892_Step_By_Step_900_Quad_V5.indd 1 1/9/10 18:01:22 Before Starting: Please read and understand these instructions. Not
More informationPedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches
88 5549 181 Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationStep by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com
Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com THANK YOU for purchasing from smith+noble. Your new window treatments have been
More informationSMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE
SMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE Please read guide before beginning any installation. Instructions/Guides Keys & Handle Screw Covers Interlock Covers Anti-Lift & Rubber Stops Anti-Lift for Slim
More information12. Wings, Flaps, Ailerons and Struts
12. Wings, Flaps, Ailerons and Struts Fit Aileron Hinges Reference: Drawing 20270K2 Photo 12.1 Parts Required: 2007092 Aileron LS 200809N Aileron RS 2001394 Hinge 3/16 A1 (4) 2001694 Hinge Pin (4) PH0059N
More information77 cm. 5243/3-GA (3 pcs.) 5243/3-BO (3 pcs.)
ARCHIMEDE ST.102-4ENG SPECIFICATION Range: ARCHIMEDE Design: Caimi Lab 5203-GA, 5203-BO, 5213-GA, 5213-BO, 5223-GA, 5223-BO, 5233/3-GA, 5233/3-BO, 5241/3-GA, 5241/3-BO, 5243/3-GA, 5243/3-BO, 5245/3-GA,
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationStraight Stringer Installation Instructions
Straight Stringer Installation Instructions Floor-to-Wall Installation F L I G H T P L A N Unpack: What s included? Your Stringer Tread Screws (8) per tread (1) Torque Wrench (1) Socket (for the brackets
More informationTable and Furniture Base Fittings Plinth Adjusting Fittings
Adjusting screw with M8 or M thread Rigid, for glide inserts, steel thread Finish/Colour: Black, thread galvanized Version: With acceptance Ø30 mm Thread M8 650.22.381 M 650.22.382 Packing: 1 or 0 pcs.
More informationINSTALLATION INSTRUCTIONS
ECLIPSE CANOPY INSTALLATION INSTRUCTIONS IMPORTANT NOTE: ENSURE ALL RELEVANT PERSONNEL READ THE POINTS LISTED WITHIN THIS LEAFLET AND THAT A COPY IS GIVEN TO STAFF INVOLVED WITH THE INSTALLATION AND MAINTENANCE
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More informationIndustrial Hanger ASSEMBLY INSTRUCTIONS
Industrial Hanger ASSEMBLY INSTRUCTIONS INDUSTRIAL HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench
More informationInstallation Instructions
Installation Instructions Walk-in Shower Screen End Panel Installation Instructions Important Information Please read these instructions carefully before starting installation and keep for future reference.
More informationSalter Industries Spiral Stair
Salter Industries Spiral Stair The Leader in Spiral Staircases Continuous Sleeve Stair Installation Instructions TOOLS NEEDED: 1. Electric drill with hex chuck and Phillips bit 2. Drill bits 1/8", 1/4",
More informationINSTALLATION GUIDE DUOFUSE SLAT WALL SYSTEM
06/2013 ENG 1 INSTALLATION GUIDE DUOFUSE SLAT WALL SYSTEM The Duofuse wood composite slat wall system is much more durable than wooden fences, and correct installation is necessary to enjoy the fences
More informationPiazzola Pergola Awning Manufacturing and installation guide
Piazzola Pergola Awning Manufacturing and installation guide Date Changes Page General information Maximum and minimum width Width Projection 150 to 349 cm 350 to 500 cm From 200 to 250 cm X From 251 to
More informationInstallation Instructions
Supafold Slide Aside System Three Fold Room Divider Installation Instructions Distinctive Doors Ltd Supafold Slide Aside Internal Folding System IMPORTANT: Before proceeding with the installation, and
More informationSUREWOOD ~ LNL. How to build a staircase like a pro. Post-To-Post Staircase System. Identify Your Type of Post-to-Post Staircase: Landing Newel Post
How to build a staircase like a pro. 1 Identify Your Type of Post-to-Post Staircase: Post-To-Post Staircase System Post Post SUREWOOD ~ LNL Wall Rail Square Top alusters Shoe rail Open Staircase with Square
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationINTRODUCTION. EqunioxRoof.com. Pro Tip
INSTALLATION MANUAL INTRODUCTION The Equinox Louvered Roof System is designed to be installed in an aluminum frame. All these sections are 1/8" thick extruded aluminum. All engineering for this system
More informationSunrise Deck Assembly Instructions for Kingston Left
Sunrise Deck Assembly Instructions for Kingston Left It s easiest to build the deck frame first like it will be lying on its back and then after all 4 legs and horizontals are in place, tip the deck toward
More informationAUTOMATIC ADVANCE MANUAL
AUTOMATIC ADVANCE MANUAL AVL Looms, Inc. 3851 Morrow Lane, Suite #9 Chico, CA 95928-8305 530 893-4915 530 893-1372 fax # info@avlusa.com www.avlusa.com Copyright 2009 TABLE OF CONTENTS Page # I. Parts.........................
More informationCXT PRO RAILING INSTALLATION INSTRUCTIONS For Installations Using Aluminum and Glass Balusters Sold Separately
CXT PRO RAILING INSTALLATION INSTRUCTIONS For Installations Using Aluminum and Glass Balusters Sold Separately CCRR-0171 PFS AA-652 Drill/power screwdriver Assorted drill bits Hammer Miter or circular
More informationAX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS
AX1001 Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM 83 84 84 85/86 87 87 88 89 90 91 62 64 64 64 64 64 64 65 65 65 65 66 66 65 66 66 65 63 63 66 67 68 55 66 66 70
More informationSPUNKY ASSEMBLY MANUAL
SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationGROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02
GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.
More informationCellar Hanger ASSEMBLY INSTRUCTIONS
Cellar Hanger ASSEMBLY INSTRUCTIONS CELLAR HANGER Recommended Tools Drill with 1/8 and 1/4 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16, 7/16, and 5/8 Combination Wrench Socket
More informationPlug sockets. page 15. Assembly instructions. page 2-3 Assembly material. page 4-6 Insertable parts. page 7-14
CONTENTS Introduction New colours version: PP-A-14-ENG PERFOPLUG BASE Plug sockets. page 1 Assembly instructions. page 2-3 Assembly material. page 4-6 Insertable parts. page 7-14 PERFOPLUG PREMIUM Plug
More informationSLP-LPC. Installation & Operating Instructions. SLP-LPC Preparation
SLP-LPC Installation & Operating Instructions Leave this manual with party responsible for use and operation. CAUTION! Do not install damaged components. The Low Profile Cap (LPC) is NOT approved for all
More informationStair Parts Installation. Tricks
Stair Parts Installation Tips & Tricks Introduction Your DIY staircase guide Welcome to the Stairpart home installation guide. Your stairway is both a functional and focal point in your home, so keeping
More informationSeries 9000 Panel Door; In-Line, Corner and Permanent Wall Application
Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer,
More informationINSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION
INSTALLATION GUIDE SLIMLINE ROOF LANTERN 4 PANE CONFIGURATION SLIMLINE STEP-BY-STEP INSTALLATION GUIDE Thank you for choosing Roof Maker, we hope you are delighted with your new rooflight. Our roof lanterns
More informationBarnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratch
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationTECHNICAL MANUAL - CONSTRUCTION AND INSTALLATION
ERGON T.E. LIVING SLIM TECHNICAL MANUAL - CONSTRUCTION AND INSTALLATION Swinging-sliding door with connecting rod on frame JAMB THICKNESS 30/40 mm CELEGON S.r.l. - Via G. Galilei, 6-30035 Mirano (Venezia)
More informationMOUNTING INSTRUCTIONS CONCRETE PURLIN BRACKET
CONCRETE PURLIN BRACKET VERSION MARCH 2015 GENERAL INSTRUCTIONS Safety: Systems may only be installed and operated by properly trained and technically suitable people (i.e. MCS accredited installers).
More informationJK Rear Crusher Flares
INSTALLATION INSTRUCTIONS INST-17-05-010_A JK Rear Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationRetractable Tongue Kit Model MPG457 Instructions
Malone MicroSport Trailer Retractable Tongue Kit Model MPG457 Instructions TM Take a few moments and read through these instructions to familiarize yourself with the step by step assembly process before
More informationIMPORTANT: WILL NOT FIT COUNTRYMAN MODELS
Part #1410-0102-07 2 3 1 IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Apply masking tape around the bottom grille opening and across the bottom of the upper facto ry grille.. Open the hood and remove the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationPillar Hanger ASSEMBLY INSTRUCTIONS
Pillar Hanger ASSEMBLY INSTRUCTIONS PILLAR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationMETAL BLINDS. Deluxe GETTING STARTED OPTIONAL HARDWARE. A few simple tools are required: STANDARD HARDWARE
METAL BLINDS Deluxe GETTING STARTED OPTIONAL HARDWARE A few simple tools are required: Steel Tape Measure Pencil Level Hold Down Brackets with Screws Extension Bracket Power Drill and Drill Bits Flathead
More informationPlatinum Swing Panel Installation Instructions
Platinum Swing Panel Installation Instructions The Standard Platinum Swing Panel is designed to fit baths with a perimeter lip no taller than 20mm. If installing onto baths without a perimeter lip an optional
More informationThe Mind Project s Iris 1 Robotic Arm. Assembly instructions Step 1
The Mind Project s Iris 1 Robotic Arm Assembly instructions Step 1 Packing list Below you will find pictures and descriptions of each part. It may be helpful to take each piece out of the bag and place
More informationAllora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED
Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating
More informationMODEL T " X 72" BEECH CABINETMAKER'S WORKBENCH INSTRUCTIONS
MODEL T1251 25" X 72" BEECH CABINETMAKER'S WORKBENCH INSTRUCTIONS For questions or help with this product contact Tech at (570) 546-663 or techsupport@grizzly.com Introduction This cabinetmaker's workbench
More informationRouter Table. Construction
Router Table A router table is an invaluable tool. The problem, however, is that ready-built router tables are usually relatively expensive and too narrow for many projects. This router table provides
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationLoft Hanger ASSEMBLY INSTRUCTIONS
Loft Hanger ASSEMBLY INSTRUCTIONS LOFT HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench
More informationCalf-Tel Pen System Assembly Instructions
Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,
More informationInstallation of Speed Cushion with Metal Strip
Installation of Speed Cushion with Metal Strip QUALIFICATIONS Safe Use of Hand Tools Manual Handling Item W / H / V/ Activity Acceptance Criteria No M / R 1 Setup Ensure you are at the correct location
More informationCopyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax
Copyright 2003. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2003 RM3010A RM315-R2 RM323-R2 RM329 RM451 RM457 RM3020A RM316 RM324-R2
More informationAluminum Frame Type Instruction Manual
Aluminum Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More informationOrganisational Kitchen Fittings Kitchen Cabinet Accessories
Kitchen waste bin systems Single waste bin, capacity 1 litres Carcase width: Min. 400 mm For door mounting: For left and right hand use Installation: Screw fixing to side panel Housing: Steel, plastic
More informationVinyl Cutter Instruction Manual
Vinyl Cutter Instruction Manual 1 Product Inventory Inventory Here is a list of items you will receive with your vinyl cutter: Product components (Fig.1-4): 1x Cutter head unit complete with motor, plastic
More informationINS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER
INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER 6-1/2" 5" 2-7/16" 3-7/16" Ø2-7/8" 4-7/8" 11" 2" 3/16" 1/2" HORSESHOE W/ BAR S P ECIFICATIONS PARTS AND TOOLS Tools Needed Tape Measure Pencil
More informationELPMB27. Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs)
ELPMB27 Short Throw Projector Wall Mount Installation Manual xxx(fr) xxx(de) xxx(it) xxx(es) xxx(pt) xxx(zhs) Safety Instructions Before using the wall mount, make sure you read all of the safety instructions
More informationWOLF PUP LOOM TM & WOLF PUP LT LOOM TM
WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212
More informationWall-Mounted Basin Set
P24702-LV 2014 1 of 6 KALLISTA THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product.
More informationSE5a Instrument Board part 2 - rev 1.1
SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More informationVersion 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS. Victorian Vi-23, 34, 36
Version 2016_1.1 VICTORIAN ASSEMBLY INSTRUCTIONS Victorian Vi-23, 34, 36 PRODUCT INFORMATION Dear customer, Thank you for buying a high-quality aluminium greenhouse. REMARKS The drawings in these instructions
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER R H
INS T A L L A TIO N INS T R U C TIO N S ROD IRON SCROLL HANGER 10.5.2016 2-1- 3/16" 11/16" 8" 8 O 2-7/8 Ø2-7/8" 3-1/2 3-1/2" 12-9/16 12-9/16" PLEASE NOTE: These instructions are specific to a particular
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationStage 2: Preparing the door (read in conjunction with Hole Drilling Options on back of Template).
There are three stages to fitting the CL100 mortise case: Stage 1: Marking out the position of the lock. Stage 2: Preparing the door by mortising and drilling holes. Stage 3: Fitting lock, door furniture,
More information