2 A6310C2 600 x 1200 x 3t 6pc Nr hue Product code Dimensions Quantity

Transcription

1 CALME Preliminary remark: beneath information accrues from sources which we consider reliable. We cannot be responsible for its correctness or exhaustion. See also our general terms and conditions. 1. Delivery control Any visible damage should be mentioned clearly on the shipping documents. Any damage should be instantly reported with (digital) pictures to Sonogamma. Opening the packaging and/or manually unloading the sheets automatically means acceptancy of its delivery. 2. Unloading and sorting - Aluminium is a natural product; small differences in hue are inevitable. Therefore, Calme is packed in cartons according the hue. There are five groups, the number of which is written on the side of the packaging, e.g.: 2 A6310C2 600 x 1200 x 3t 6pc Nr hue Product code Dimensions Quantity - About 80% of the sheets is sorted as hue nr 3. An adjacent sheet should have the same number, one higher or one lower. A sheet nr 3 can be mounted next to a nr 3, 2 or 4. Group 3 can be mounted in the middle of the surface; nrs 1 and 5 only at the edges. - Sorting is not compulsory. Mounting the sheets randomly results in a natural variation in colour and hue. - The panels are packed in the same direction. The direction of the panel is noted on the packing and on the backside of each panel. The panels should be installed in the same direction.

2 The panels should be installed in the same direction, following the direction mark on the backside. GOOD WRONG 3. Treatment - Calme sheets can be cut with a Stanley knife, bandsaw, laser cutter. - Holes up to 80 mm can be drilled on site; holes larger than 80 mm need to be foreseen at the factory. - Calme can be bent by hand at a radius of at least 3 m or more. Smaller radiuses are bent by use of a bending machine. 4. Colour coating - The sheets are painted with a aluminium grey acrylic paint. - The sheets can be painted at the factory in any colour. The absorption is only guaranteed when painted in our factory. 5. Cleaning - Small stains can be erased or wiped clean with a cloth. - The sheets can be vacuum cleaned (use soft brush). - Tough stains can be cleaned with a soft, diluted detergent. Never use hard detergents or chemical products for they can cause discoloration or damage. - Calme type C (swimming pools and outdoors) can be hosed down. Always perform a test on an unvisible part of the ceiling or wall. 6. Shrinkage/expansion The sheets expand a mere 0.6 mm / 1200 mm at a temperature difference of 30 C. If this occurs (outdoors, glasshouse, ), a joint of 1 mm between the sheets should be foreseen.

3 7. Floodlight Floodlicht makes any irragularity visible. It is therefore strongly recommended not to combine floodlight with Calme panels 8. Mounting The sheets can be mounted with double sided tape or rivetted or screwed. In the latter case, the sheets are predrilled. In case of glueing, no mounting details are visible. The sheets ar mounted with no joints. 7.1 Ceiling The screws or rivets are applied at min. 12 mm from the edge of the sheet. The profiles are 50 mm wide. In case of steel bars, use inox screws and double sided adhesive tape in order to avoid a galvanic reaction. Examples: System 190 Suckow & Fischer (double grid) Hanger 300 mm S&F system 190 Calme sheets

4 Systeem 195 Suckow & Fischer (single grid) 600 mm Hanger S&F 195 Calme sheets 7.2 Wall Calme can be screwed on a wooden frame or mounted with doublesided adhesive tape. Wooden slats: 50 mm wide

5 When applied in circulation areas, a perforated MDF or steel plate can be applied in order to enhance the mechanical resistance. The perforation rate should be at least 20 %. The maximum diameter of the holes is 20 mm.

6 Section A: mounting with perforated MDF panel 7.3 Finish corners The corners can be finished with aluminium or wooden corner elements. In following examples, a perforated plate is used. Outside corner 1 Outside corner 2 Wooden slat Wooden slat Alminum profile Alminum profile Outside corner 3 Inside corner Wooden slat Houten regel L - profile Wooden corner element 9. General remarks Handle with care. Always store the sheets flat. Don t put loads on the panels to avoid bowing. In case of bowed sheets, try to reshape them by pressing them on a flat surface with a wooden block. It s strongly advised to wear gloves to avoid stains or fingerprints on the sheets.