Serial Number Your arm was hand built for you by; Date

Size: px

Start display at page:

Download "Serial Number Your arm was hand built for you by; Date"

Florence Cross
5 years ago
Views:

Thanks for Buying The Wand Master Unipivot Tonearm The best tonearm in the world will sound like the worst if it is badly set up.

Installation videos may be accessed via or the QR code The Wand Tonearm has been meticulously designed using computer modeling and refined by listening.

Your Tonearm Serial Number Your arm was hand built for you by; Date Designed and hand-made in Aotearoa / New Zealand by design build listen Ltd. P.O.

1 Thanks for Buying The Wand Master Unipivot Tonearm The best tonearm in the world will sound like the worst if it is badly set up. These instructions will help you achieve great performance with your tonearm. Installation videos may be accessed via or the QR code The Wand Tonearm has been meticulously designed using computer modeling and refined by listening. All attention has been focused on maximizing musicality, this you never grow tired of. The Wand Tonearm, musical magic! Your Tonearm Serial Number Your arm was hand built for you by; Date Designed and hand-made in Aotearoa / New Zealand by design build listen Ltd. P.O.Box 5415, Dunedin 9058, New Zealand Ph / Fax; Features of The Wand Master Tonearm Big diameter (22mm) carbon-fibre tube is 4x stiffer than a normal diameter arm. Ergonomic cueing via tip of arm or damped cueing mechanism. Laser sintered titanium headshell and great termination of arm vibrations. Defined contact bearing. Low friction while maintaining energy transmission. Medium effective mass suits most cartridges. (13.5g for 9in, 15g for 10.3in, 16g for 12in) Drop in replacement for Rega geometry arms (~240mm). SME, Technics, Linn & Lenco mount options. Silver/Copper hybrid wire with captive female RCA/phono plugs Thread / weight type antiskate. Standard Baerwald alignment (with consideration given to real world inner groove dimensions). Vibration shunt (damping trough) and it looks really cool! Winning Silver at the 2016 BEST Design Awards

81mm The Wand dimensions & data; Check the arm will fit on your turntable before you start. Data; Weight =0.75kg (0.8kg for 12in) Effective mass of arm = 13.5g (15g for 10.

2 81mm The Wand dimensions & data; Check the arm will fit on your turntable before you start. Data; Weight =0.75kg (0.8kg for 12in) Effective mass of arm = 13.5g (15g for 10.3in, 16g for 12in) Warranty; 2 years (Note; shipping cost to us is the responsibility of the sender.) 28 min Record Surface Stylus to Pivot 240mm (262mm for 10.3in arm) (308.8mm for 12in arm) Pivot to TT Spindle 222mm (246mm for 10.3in arm) (295mm for 12in arm) Ø50> Ø23> 55 max 40mm min Check what we have sent you ; Supplied Picture Sent Check Supplied Picture Sent Check Grease (In a tube) Below 1 M5 screws (2 diff.) C1 2 Cartridge Screws A2 2 M4 screw G3 1 Cartridge Spacer A4 2 Ortofon Balance D2 1 Protractor B1 1 Arm Lift Assembly E1 1 Spindle Assembly B4 1 Anti-skate weight E3 1 Hex Keys B4 3 Silicone Oil E5 1 Check what tools you need; Tools you need (Not supplied) Drill; 6mm (or ¼ ) Drill; 24-25mm (1 ) Check Small flat bladed screwdriver Pozi or Philips Screwdriver Long nose pliers or tweezers Maintenance; Re-grease the bearing tip occasionally with the grease supplied. (Touch tip in grease as shown >) Problem Solving; If the arm is not performing well; Check the stylus is clean. Check the cartridge tracking weight. Check the wires are not pushing the arm sideways. Notes; Don t ship the turntable with the arm on the spindle. Black and silver metal parts may be lightly oiled to keep them looking good. (Do in humid climates) With our continuous improvement program the parts shown here may be slightly different from yours.

A Fitting & Balancing the Cartridge Step 1; Rough Balance Three plates are fitted to the arm as shipped. This is fine for the majority of cartridges.

Extra plates can be ordered for really heavy cartridges (>11g) The smaller square edged plate can be used to give an intermediate step and on its own for light cartridges.

Either for a very light weight cartridge or a very low compliance cartridge. WARNING; Be careful, cartridges are easily damaged. Use your stylus guard.

3 A Fitting & Balancing the Cartridge Step 1; Rough Balance Three plates are fitted to the arm as shipped. This is fine for the majority of cartridges. But if your cartridge is light (<6g) you will probably only need one plate. If you cartridge is heavy (>8.5g) it is likely you will need three or more plates. Extra plates can be ordered for really heavy cartridges (>11g) The smaller square edged plate can be used to give an intermediate step and on its own for light cartridges. Plates Step 2; Attaching the cartridge Where possible use the supplied Aluminium M2.5 screws unless; Your cartridge has tapped holes (use screws supplied with cartridge). You need more mass. Either for a very light weight cartridge or a very low compliance cartridge. WARNING; Be careful, cartridges are easily damaged. Use your stylus guard. Screws should be done up firmly but not over-tightened. We cannot be liable for damage to the cartridge either in installation or use. Step 3; Attach the Leads to the cartridge Left (Black) Blue=Left Ground White=Left + / Hot Right (Red) Red=Right + / Hot Green=Right Ground Cartridge Spacer Option;. You have been provided with a small metal plate with two holes. This may be put between the cartridge and the arm in three circumstances; If the cartridge is too light to balance If the cartridge suit a heavier arm (This spacer adds 2g) eg; Denon DL103 If the cartridge is short or touches the carbon fibre when installed. NOTE; Vertical Tracking Angle may need to be higher than indicated in section B4 A 5g weight is available as an option, just ask.

B Drilling the Mounting Hole for The Wand Tonearm Rega hole is ok(9in) Step 1; Check rear & side clearance to

The protractor you receive may be different from the below (as they are being updated).

$\ Step 3; Drill 23-25mm hole (1 ) Use 6mm hole as guide for drill (from Step 2 above) Existing holes up to 28mm$ Put the spindle in the round plate (The black lever unlocks clockwise but it will still be firm to fit) Sit the

Put the spindle in the round plate (The black lever unlocks clockwise but it will still be firm to fit) Sit the

Lock the spindle with the hex key in the side hole as below.

4 B Drilling the Mounting Hole for The Wand Tonearm Rega hole is ok(9in) Step 1; Check rear & side clearance to the turntable lid You need at least 50mm / 2 from the centre of the hole to the side or back of the lid Note; The protractor you receive may be different from the below (as they are being updated). Shown at right top to bottom; 9in / 12in Step 2; Drill 6mm Pilot hole (1/4 ) Through the smaller hole. \ Step 3; Drill 23-25mm hole (1 ) Use 6mm hole as guide for drill (from Step 2 above) Existing holes up to 28mm are fine. (Contact us about holes 28mm to 48mm which can be made to work) Step 4; Set arm height. Put the spindle in the round plate (The black lever unlocks clockwise but it will still be firm to fit) Sit the protractor on the playing surface. Adjust the height as below. Lock the spindle with the hex key in the side hole as below. < Hex Key here -Arm at +2 degrees -Arm level (nominal) Note; We suggest starting with the arm level. Later adjust upwards by ear. 2 degrees up may be good. This exact height depends on many factors. (See; P29 SRA, VTA & My Sonic Lab by Michael Fremer Stereophile June 2010)

C Fitting The Wand Tonearm Mount Step 1; Feed the bolt down to the boss on

Two screw lengths are provided for different plinth thickness.

Note; If you wish to pass the RCA / Phono plugs through the plinth you will

See below But we don t recommend doing this on initial installation as it is

Step 2; Remove rubber transit cap. Step 3; Position mount using protractor.

Use supplied hex key Hint; Cueing with The Wand Tonearm We suggest using the

5 C Fitting The Wand Tonearm Mount Step 1; Feed the bolt down to the boss on the clamping plate and do up loosely (but not tighten yet). Two screw lengths are provided for different plinth thickness. The lower clamping plate may go either way up. Note; If you wish to pass the RCA / Phono plugs through the plinth you will need to feed them through the slot at this stage. See below But we don t recommend doing this on initial installation as it is easier to lift the arm off for adjustment. Get it running first. Step 2; Remove rubber transit cap. Step 3; Position mount using protractor. (Rotate to get in the correct place). Step 4; Tighten to clamp. Use supplied hex key Hint; Cueing with The Wand Tonearm We suggest using the side of your finger. Rather than trying to grip the tip. Other Protractor systems; If using another brand of protractor. The centre of the pivot is aligned with the shoulders of the main body.

D Fitting the Arm Wand & Setting Overhang Step 1; Add

Adjusting this slightly affects the rest height of the

(armrest omitted for drawing clarity here) Step 3; Guide

. (See also Page G) Feed the purple part of wire into the

above the arc XY NOTE; To avoid damage to the stylus, do

6 D Fitting the Arm Wand & Setting Overhang Step 1; Add Armrest Align to level with the step in spindle. Adjusting this slightly affects the rest height of the arm) Lock with small hex key (Two screws) Step 2; Place arm on Mounting IMPORTANT! Make sure the turntable plinth is level at this point. (armrest omitted for drawing clarity here) Step 3; Guide cables.. (See also Page G) Feed the purple part of wire into the black P-Clip, Slide to thicker section, so it forms a loop. Step 4; Overhang setup. A) Swing the protractor and arm round so the stylus is above the arc XY NOTE; To avoid damage to the stylus, do not let it touch the protractor (hold slightly above) B) Swing above the arc X-Y. If it doesn t align at either end then C) Loosen the screw (below right) and rotate until it aligns through the whole arc. X Y

E Vertical Balance & Sideways Balance (VTA & Azimuth) Step 1; Vertical Balance (Tracking weight,

. and rotate the rear bolt to set fine balance.

Lift the arm off the scale when doing this.

from the front). Use protractor as below.

force; (Approximate only, refine by ear or test record as desired.

Tracking Weight / g Position A-C (below) < 1.0g No Weight C B 1.0-1.6 C A 1.6-2.2g B >2.

7 E Vertical Balance & Sideways Balance (VTA & Azimuth) Step 1; Vertical Balance (Tracking weight, as recommended by your cartridge maker.) Use supplied balance scale (15mN = 1.5g etc).. and rotate the rear bolt to set fine balance. Too light; Wind bolt in or take off a plate if the bolt is right in (see section A1). Lift the arm off the scale when doing this. Correct; Back part is level Too heavy; Wind bolt out or put on a plate if the bolt is right out (see section A1). Lift the arm off the scale when doing this. Step 3; Side Balance (Azimuth); Aim; To have the stylus standing vertical in the groove (Viewed from the front). Use protractor as below. Adjust side balance by moving the rear balance plate as below (Shown as red) Step 3; Add antiskate force; (Approximate only, refine by ear or test record as desired.) Hint; To stop the loop slipping towards the body you can slide the rubber plug along the rod. Tracking Weight / g Position A-C (below) < 1.0g No Weight C B C A g B >2.2 g A Step 4; Plug into amplifier. Red into Right, Black to Left & green wire to green earth post (If no earth post, try attaching to amplifier chassis) Our wiring is low capacitance so some cartridges maybe better with more. Enjoy! We also recommend: Fozgometer or Adjust Plus tools Arm Catch: The arm may be latched when parked, as below. (Left unlatched, Right latched)

F VTA (Vertical Tracking Angle) Adjustment It is assumed you have got the spindle at roughly the right height (see Page B Step 4) Twist the knurled dial anticlockwise to wind the fork down

Step 2; The main spindle has two separate locking mechanisms -Hex key -Black Friction lock lever (Unlocks clockwise) -Release them both Step3; Twist the knurled dial to adjust VTA Lock.

When adjusting VTA downward, finger Pressure may be needed to help it down. Using the Vibration Shunt; Your Wand Master Series has been provided with a Vibration Shunt.

Using this is system and taste dependent, it may be easily raised and lowered.. Step 1; Fill Start using the lower viscosity (smaller number), fill to 2/3 the depth of the trough.

8 F VTA (Vertical Tracking Angle) Adjustment It is assumed you have got the spindle at roughly the right height (see Page B Step 4) Twist the knurled dial anticlockwise to wind the fork down till it touches the mounting plate. Step 2; The main spindle has two separate locking mechanisms -Hex key -Black Friction lock lever (Unlocks clockwise) -Release them both Step3; Twist the knurled dial to adjust VTA Lock. Use the friction lock if you frequently adjust VTA or if you generally are happy with one setting use the hex hey to lock it as this is more rigid. When adjusting VTA downward, finger Pressure may be needed to help it down. Using the Vibration Shunt; Your Wand Master Series has been provided with a Vibration Shunt. While this may also be seen as an arm damper the thought behind this naming is that this is designed to shunt vibrations from the arm using a silicone oil trough. Using this is system and taste dependent, it may be easily raised and lowered.. Step 1; Fill Start using the lower viscosity (smaller number), fill to 2/3 the depth of the trough. Step 2; Engaging the Vibration Shunt. With the arm in place, raise the trough by turning the knurled dial clockwise. Raise it till the threaded rod on the underside of the arm is just in the silicone. Listen! To disengage, just wind the trough down. Once you have found a position you like, the trough may be locked in place using the lock nut on the inside end. If you want to change oil (or remove it) use a cotton bud and paper towel.

G Mounting the Plugs on the bottom of the spindle

9 G Mounting the Plugs on the bottom of the spindle (Optional) Step 1; Disassemble the Plug Clamp Step 2; Feed the plugs through the mounting hole Then fit the top / bottom mounts, feeding wires thought he slots. Add bolt and do up. Step 3; Use the supplied 4mm Bolt to secure the plugs to the shaft.

10 Cartridges & The Wand Tonearm; The Wand Tonearm lets cartridges express themselves for what they are but not neutral in the cold and analytical sense. So cartridge recommendation comes down to the flavour you like. The Wand is "Medium Mass" at 12.5g effective mass (15g for the 12in), so will work with most cartridges. Even a high compliance cartridge like a Shure V15Vx gives a measured resonance at 7Hz, so is ok. At the other extreme, conventional low compliance cartridges work well. Arm/Cartridge matching is frequently over-stated, unless you have a system with massive bandwidth or insist on playing badly warped records, it shouldn't be an issue. The Wand Tonearm has been used with some of the world s best cartridges. Two of my retailers have independently chosen Transfiguration cartridges, one of them having settled on the Axia & Phoenix S. (after trialling Ortofon s Cadenza Red & Black along with the Rondo Blue, ZYX B50 Bloom & Zu / Denon 103.) But many users have exotic Japanese cartridges, particularly ZYX models. My Swedish & French Distributors favour Lyra and Dynavector cartridges which are at the analytical / quick end of the spectrum. Miyajima are musical cartridges and work well with The Wand. Analogue Works and my German distributor like dynamic /punchy cartridges, both have used Soundsmith, Nagaoka and Decca London. The latter is very notable as Decca s are wonderful (I had one) but are fickle and very hard to match to arms. Ask for our Blog on why The Wand is a good match for Decca s. Popular Cartridges; Denon 103 and related cartridges are the most popular to use with The Wand, (they have a grand sweeping sound). Ortofon 2M Blacks are popular but may hum in some systems. Hana have a wonderful balance of virtues. Dynavector DV10x and 20 are also popular and seem to work well. In terms of high output cartridges; Sumiko Blue Point are good options. Nagaoka cartridges are wonderfully dynamic and punchy without being edgy. Problem Solving; Mounting the arm; -The existing Mounting hole is too big; -Holes up to 28mm are fine -For holes 28-48mm we can provide an alternative clamping plate, contact us. -For holes above 48mm, you can use out SME style mounting plate. Contact us. -There is not enough space beside the mounting plate; We can provide a smaller diameter mount. -The platter is too low or high; if the platter is too low (<23mm from the arm mounting surface to the top of the platter), you may have to use a thicker mat. If the platter is thick, a thicker mounting boss is available. (the black mounting part can be turned over too). Contact us. -The plinth is too thick / thin; For thicker plinths, longer bolts or top mounting may be substituted -The mounting hole is in the wrong place; Generally you will have to drill a new hole but there is a kit that gives an offset hole. Designed originally for Lencos, this may work in other contexts, just ask. Noise problems; Always tricky as you can have too many earthing points as well as to few. A great resource is Jim Hagermans website; Be aware that that Carbon fibre has less electromagnetic shielding than metal so may be more prone to hum pickup with MM cartridges. But this is very system dependent. We offer a short leads option that may help. Setting up the cartridge: -Tracking weight is too low; If the bolt can t wind in far enough, remove a plate (or two) -Tracking weight is too high; If the bolt can t wind out far enough, add a plate (or two) If neither of these work, talk to us! -If you can t get the azimuth right; talk to us. -If you can t get the antiskate right; talk to us. Dec 2012 design build listen Ltd. v17

Serial Number Your arm was hand built for you by; Date

Serial Number Your arm was hand built for you by; Date Thanks for Buying The Wand Plus Unipivot Tonearm v2 The best tonearm in the world will sound like the worst if it is badly set up. These instructions will help you achieve great performance with your tonearm.