PVC-u Product Installation Guidelines
|
|
- Tyler Stokes
- 5 years ago
- Views:
Transcription
1 PVC-u Product Installation Guidelines All upvc Window, Door and Conservatory products must be fitted in accordance with current codes of practice. Current Codes of Practice British Plastics Window Federation Code of practice for the Survey and Installation of upvc Windows and Doors The Glass and Glazing Federation document Installation of Windows and Doors in domestic properties (1996 edition and any subsequent updates). All relevant installation data sheets issued by Dempsey Dyer Ltd and Deceuninck including those relating to cavity closers. Please see also our General Conditions of Sale and Maintenance Guidelines. Examples of some common installation errors are as follows: lows: 1. Bridging Glass Packers (Which allow moisture to travel underneath the packer) must be fitted to all bottom rebates and must be placed to one side of the drainage holes. If the drainage system is blocked, water cannot escape from the rebate with consequent leaks and failed units. Bridging packers suitable for the glazing system can be obtained from Dempsey Dyer Ltd in packs of Top and side of sash 2849 Bottom of sash mm Glass Packer FOR 2500 & 2800 Series FOR 2500 & 2800 Series FOR 3000 SERIES 2. A low modulus silicone seal must be applied to the underside of the window frame in the groove directly behind the drain holes. This seal must connect with the mirror image topside of the cill to form a complete water barrier. This seal is continuous along the flat of the cill from brick to brick. On bay windows, the seal must continue under or round bay poles. If no seal is applied, there is a danger that under extreme weather conditions of wind and driving rain, water can penetrate between the cill and frame and enter into the inside of the building. 1
2 3. Over tight survey tolerances. Over tight survey tolerances on for example upvc doors will result in either a bowed door case or inadequate room for the door to expand in in warmer temperatures resulting in sticking door locking mechanisms. Tolerances - Woodgrain doorsd Require a minimum clearance tolerance between brickwork and profile edge of 7mm (14mm overall). Tolerances - Woodgrain windows Require the same 14mm overall fitting tolerance. Expansion Joint - Woodgrain windowsw The joint should not exceed 3mts long without the introduction of an expansion joint. The expansion joint is achieved with P1130. This allows 5mm tolerance between the woodgrain windows and the P1130. The 5mm tolerance applies to the woodgrain products fitted in conservatories. 4. Toe and Heeling To ensure correct operation of the opener and avoid damage to the ironmongery 5. 3D Hinge Adjustment on PVC & Composite Doorsets Doorsets are pre hung in the factory and delivered to site with the 3D Hinge adjustments ready for installation. 3D hinges can be adjusted on site to allow door mechanisms to operate smoothly. See the relevant sections, 18,19,20, for the correct adjustment method. 6. Lock Operation For all door locks remind your customer to engage the lock do not leave on the latch. If Door locks are not engaged then severe weather temperature changes may distort the sash frame relationship resulting in the mechanism fouling or EG a bow in the door sash resulting in weather penetration. 7. Installation of Cavity Closers See 1. Above Ensure Cavity Closers are not deflected out of square by the brickwork. Otherwise the window or door frame will not fit. 8. Installation of Windows See 1. Above and current codes of practice. 9. Installation of Beaumont Windows Outer frames must be correctly packed and sashes toe and heeled to avoid deflecting the outer frames and sashes at the mechanical corner joints. 2
3 10. Installation of Doors 10.1 Clap Ons - for all open in Residential and French doorsd (and some open out) Consider ordering with either 15mm or 25mm clap ons on the hinge side to suit site survey requirements. In addition to the clearance required between the upvc outerframe and the brickwork, the clearance between the door hinge and the plaster work/tiling/brickwork should also be taken into account when surveying. It is likely that a clap-on will be required to the hinge side of the doorframe (and possibly to the other side for symmetry). Photos of Typical hinge to outerframe rame clearance When a 15mm, 25mm or 40mm clap on is applied to the hinge side of the doorframe. (These clearances can vary according to sash/frame weld tolerance). 15mm Build-up 25mm Build-up 40mm Build-up 10.2 Installation Guidelines for PVC-u Doors in addition to the current codes of practice. 1. Offer the upvc doorframe complete with door sash into the prepare brickwork opening, ensuring an even clearance on all sides between the upvc outerframe and the brickwork. On white upvc this gap should be a minimum of 5mm between the outerframe and the brick work and on the woodgrain upvc this should be a minimum of 7mm. 2. Use glazing packers or fixing cleats to maintain this clearance 3. Check with the door wedged in this position that the door sash has even margins on the top, locking side and bottom. The distance between the edge of the outerframe and the sash should be approximately 34mm +/- 3mm. 4. Open the sash and support its weight to avoid distorting the wedged frame. 5. Fix the doorframe securely using PVC frame anchors 150mm from the Frame corner and transoms and at a maximum of 600mm between fixing centers. Choose the length of the frame anchor to account for any build up to the frame side. The anchor must penetrate the brickwork by at least 50mm. Ensure these fixings are secure and that fixing packers are placed between the frame and the brickwork at all fixing points to ensure that there is no Frame distortion. 3
4 6. Doors installed into new build openings should use the fixing method in point 5 above (frame anchors). DO NOT USE FIXING CLEATS. The use of fixing cleats does not provide a ridged enough fix and as a result settlement / movement will occur between the door case and the masonry when the door is operating resulting in the door dropping and a consequent remedial visit to re-toe and heel the door set. 7. If necessary the centre of the door frame locking leg can be fixed slightly bowed into the building (open out) or bowed externally to the building (open in) in a concave manner to ensure that when the door leaf closes against it in the latched locking position good gasket contact is maintained at the top and bottom. 8. Low mobility aluminium thresholds should be sealed ed to the floor with a silicone bed and secured to the floor using a fixing in the centre of the threshold. Silicon the fixing point to ensure the moisture does not penetrate. When the doors are correctly glazing and operating, the holes for the shoot bolts should be drilled through the threshold using an 8mm drill bit. 9. On French doors ensure the gap between the door leaves on the opposite face to the vertical French mullion is approximately a) for mm b) for mm c) for mm Adjustments on the door hinges and smaller type locking mechanism Gasket Hinge Adjustment (VBH Sigma) 5mm Allen Key for horizontal movement. Concentric cam hinge pin to increase/decrease gasket compression. 5mm Allen Key vertical height adjustment on bottom of bracket +5mm 4
5 11. Locking Mechanism (Maco GTS) The amount of compression between roller cams and the keep located on the outer frame axis can be adjusted by rotating the locking cam on the keep with a 4mm Allen key. (The cam is on an eccentric axis). The tightness between the claw hook and the hook pocket located on the door frame it engages into is adjustable by 2mm using a 4mm Allen key on the pocket. The centre latch is adjustable by releasing the screws on the face and moving the latch plate. Please note brick dust, plaster,debris or incorrect alignment of the door sash in the frame will cause stiff operation of the locking mechanism, putting undue pressures on the mechanism leading to premature failure. Please ensure all mechanisms and cam points are clean and lightly lubricated with a proprietory silicone spray periodically, subject to use. It is recommended that this operationj is carried out at handover and then annually. 5
6 12. Toe and Healing All doors and side hung windows must be toe and heeled in accordance with the current codes of practise. All toe & heeling packers are bridging packers and are self locating. If there is no toe and heaaling or packers are not siliconed into place, the door or side hung window will drop from square, snag the frame when closed, be difficult to close and consequently damage the locking mechanism and handle. 6
7 13. Dummy Sash Clips Fitting the Dummy Sash Lock A. B. Fit the Paddle Plate DSL001 onto the frame packer. The clip-in feature holds the paddle plate in place for fitting. All fixings should be secured into steel reinforcing. Screw the Frame Packer and Paddle Plate, using 2x4.3x25mm countersunk head screws, by sliding the sub assembly into position so that the dowel locates up to the outer framer as shown C. D. Using 3x4.3x25mm screws fit the Top Plate DSL002 on to the Frame Packer sub assembly as shown. Fit a Sash Packer with a Sash Plate DSL003 using the dowel to locate the assembly in the correct position. Use 3x4.3x25mm countersunk head screws to fix as shown. Fit Carriage Cap when required E. If using Release Instruction Labels, place them on the sash at the position above. 7
8 Making sure to hold the Release Tool firmly and with the blade flush to the sash internal face, push straight down between the sash and the outerframe in the area shown. This action disengages the Paddle Plate away from the Sash Plate. Now roll the Release Tool forw3ard to move the sash outwards and away from the frame for approximately 20mm Repeat this as required to the other Dummy Sash lock positions as required Please note; Due to the dryness of some gaskets it may be advisable to spray the corner with soapy water to assist this operation. Please note: Occasionally, the Dummy Sash Lock will move into 2Lock Out position when moving forward and will not release. This will require the operator to push the sash back into place and return to the first instruction above. The sash will require medium force to engage the Dummy Sash Lock. It may be necessary to check the seal around the sash to make certain it is correct. Further pressure on the sash may be applied to give a tighter seal if required. If three dummy sash lock assemblies are positioned on any one side then it may be advisable to use two release tools at the same time. One would release a corner assembly whilst the second would release the central assembly, then the third can be released on its own. 14. Security Glass packers must be inserted in glazing rebates adjacent to and directly opposite all locking points allowing less flex in the profile in the event of a jemmy attack. Glazing security clips are provided for all externally beaded glass units. 8
9 15. Bay Windows PVC Replacement. The following points must be taken into account: Out PVC window frames are not load bearing The Deceuninck PVC bay poles are load bearing subject to the pole diameter and length and the imposed load from the building structure. The customer is responsible for calculating the dead load on the bay and then specifying the pole size ensuring the dead weight of the bay structure does not exceed the load bearing capacity of the Deceuninck bay pole. There is a matrix available from Dempsey Dyer Ltd showing the load bearing capacity of the Deceuninck pole correlated to its length. The frame legs adjacent to the PVC bay pole will reinforced unless you the customer instructs otherwise. The cill section supporting the pole is not reinforced The customer must also ensure that the dead load is transferred from the existing structure to the replacement PVC bay poles and that no loading is transmitted to the PVC window frames. If you are in any doubt about whether a bay is load bearing, we advise you to consult a structural engineer before ordering. The bay pole systems available are: System 1: Deceuninck bay pole. 90 Degree Square pole Angled Pole System 2: : Window Widgets. 90 Degree Square pole Angled Pole NOTE1: NOTE2: NOTE3 : All load bearing poles are a supplied with Bay Pole Jacks. Cills must be drilled to accept a bay pole jack so the base b of the jack is in contact with the masonry at the cill and at the head. Angles greater than 170 degrees exceed the Deceuninck bay pole design limit. Window Widget poles are supplied for angles greater than 170 degrees. 16. Tilt & Glide Patio Doors Fitting points in addition to the GGF guidelines: Ensure the bottom of the outerframe is level and check with a spirit level and pack accordingly Ensure that the outerframe and track are fully supported along the length in order to take the weight of the cantilevered door when in open position. Ensure the outerframe is fitted square; any deviation from square will significantly distort a large frame. Ensure that before the patio installation is completed, the wheels on the two tandem trolleys are adjusted to take the weight of the glass. The glass is packed into the door sash to result in the sash being vertical to the outerframe otherwise the locking mechanism will collide on closing. When opening and closing the door the bottom arms of the wheel assembly must clear the outerframe, otherwise the mechanism will not work. The door enters into the frame without catching the strikers at either side. Adjustment of the transom trolley wheels (See diagram below). 9
10 Gently apply upwards pressure to the cover cap of the runner and slide up. At both ends of cover insert a small screwdriver under the cover to release the cover. Take care not to damage the aluminum. B 10
11 17. Composite Doors Solidor (These installation guidelines are also supplied with every Solidor product. There is also a customer after care leaflet supplied with every Solidor product. The standard lock is the MACO CTS The optional lock is the Winkhaus Key Wind and Heritage Slam Shut Lock. Lock Operation: For all door locks, remind your customer to engage the lock- do not leave it on the latch The 3 Way 3D Adjustable Hinges by Simonswerk. 11
12 12
13 18. Composite Doors Distinction Doors The standard lock is the Fullex Lock The optional lock is the Maco CTS Lock The 3 Way 3D Adjustable Hinges are by Simonswerk 19. PVC Doorsets with Beaumont Window The hinge supplied is a SFS 3D Adjustable Hinge 20. Hinge adjustment notes: Simonswerk 3D Hinge IMPORTANT SAFETY NOTE Ensure all adjustment screws are tightened up to the correct Torque of Nm using a torque screwdriver otherwise the door could move or slip off its hinges. Hinge Data Lateral Adjustments Clockwise, to move door to right, Anti- Clockwise to move Height and Compression Adjustment Anti-clockwise to loosen adjustment screw, clockwise to tighten the adjustment screw the 3D hinge - three per door leaf ( 4 on larger leafs) All hinges are supplied with a burglar security device, Which are required on outward opening doors. The hinge is supplied in a KTL Gold or SAA finish. Stainless Steel 3 D hinges are available for Composite doors. The hinge has the benefits of: Easy on site adjustments - if required - to door leaf gap tolerances - subject to tolerances remaining within our guidelines Doors can be lifted off hinges e.g. for ease of handling. 3 Way Height t & Compression Adjustment. Use a 4mm Allen key for all actions. The adjustment is to be carried out without taking the door off the hinges. Open the door by approx. 90 degrees and fix it by wedging. Loosen the two clamping screws of each hinge Adjust the height (+/- 3mm) and the gasket compression (+/- 4mm) of the door leaf by moving the sash carefully in the appropriate directions and fasten the clamping screws again. This operation must be carried out by two people, one of whom Is holding the door at all times, and the door must be sat on a packer in the open position to prevent the door from falling off as all adjustment screws to the 3 or 4 hinges must be turned at the same time. 13
14 3 Way Lateral Adjustments Use a 4mm Allen key for all actions. Open the door by approx. 90 degrees and stabilise it with a wedge. Adjust the lateral (Sideways) position (+/- 2mm) by turning the upper and lower screw of each hinge. 21. Finishing Off A full range of trims are available 22. Health & Safety. A reminder to follow HSE Health & Safety Guidelines applicable to an installation which include: Safe access and working from heights Manual handling Identification and control of hazardous substances COOSH (Control of Substance Hazardous to Health). INCLUDING ASBESTOS! 14
Installation Guide. Evolve bi-fold. 8. Door restrictor- optional p9. 1. Before you start p2. 9. Adjustment. 2. Measuring and surveying p2
Evolve bi-fold Installation Guide 1. Before you start p2 8. Door restrictor- optional p9 2. Measuring and surveying p2 3. Configuration details p4 4. Installation p5 5. Glazing p5 6. Glazing packer details
More informationLiniar Window. installation guide
Liniar Window installation guide This installation guide is designed to show you the best way to fit Liniar windows, and covers all styles of window made from Liniar s lead-free 70mm PVCu profile. Not
More informationSMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE
SMART SYSTEMS VISOGLIDE+ INSTALLTION GUIDE Please read guide before beginning any installation. Instructions/Guides Keys & Handle Screw Covers Interlock Covers Anti-Lift & Rubber Stops Anti-Lift for Slim
More informationInstallation Guide. Bi-fold Doors
Installation Guide Bi-fold Doors Installation Guide Components box 1. 6. 2. 3. 7. 5. 4. 8. Contents 1. Fixing plugs 2. Wedge gasket 3. Bottom trolley 4. Top trolley 5. Magnetic keep (x 2 if door height
More informationFITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF55 & SF75 WITH WEATHERED OR FLUSH TRACK
FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF55 & SF75 WITH WEATHERED OR FLUSH TRACK Please refer to your order or detailed sectional drawing (if requested) to assist you with the configuration
More informationInstallation - Sub Cills
Installation - Sub Cills Fitting of Subcill Drainage paths through the sub-cill can be seen on the illustration alongside so care must be taken to ensure they are not obstructed and that screw fixings
More informationFITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF75H
FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF75H 01603 424434 Please refer to your order or detailed sectional drawing (if requested) to assist you with the configuration of the system supplied
More informationPvcu Bi Folding Doors Fitting Instructions.
Pvcu Bi Folding Doors Fitting Instructions. THE FOLLOWING INSTRUCTIONS ARE GIVEN IN GOOD FAITH AND ARE FOR GUIDANCE ONLY. NO RESPONSIBILITY WILL BE ACCEPTED FOR ANY MIS- INTERPRETATION. WHEN INSTALLING
More informationpatio door installation guide
patio door installation guide Measuring & surveying p2 Mechanical jointing p5 Installation p5 Hardware adjustment p7 Sealing of outer frame p7 Cleaning p7 Walk through clearances p8 Minimum and maximum
More informationASS 70 FD folding / sliding door. Installation Guide
ASS 70 FD folding / sliding door Installation Guide IMPORTANT! These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the installation.
More informationXL JOINERY LTD LA PORTE VISTA MODULAR 3 ASSEMBLY INSTRUCTIONS
XL JOINERY LTD LA PORTE VISTA MODULAR 3 2090mm High x 4687mm Wide ASSEMBLY INSTRUCTIONS READ AND UNDERSTAND THESE INSTRUCTIONS FULLY PRIOR TO STARTING INSTALLATION. IT IS STRONGLY RECOMMENDED THAT A COMPETENT
More informationFor Installer. Duration Windows. Assembly Guide Durafold 1000
For Installer Assembly Guide Durafold 1000 Contents Title Page Number Handling Manual Blinds 4 Handling Electronic Blinds 5 Drainage 63 Outer Frame Assembly (Kit Form Door Only) 7 15mm Low Threshold Assembly
More informationFolding Sliding door system
Folding Sliding door system Installation guide V1.1 Nov 2014 p2 This document is offered as guidance for WarmCore folding sliding door installations - for full survey and installation guidelines please
More informationInstallation and Glazing Guide
Installation and Glazing Guide Effective January 2013 Contents Before you start Door Set installation Fixing positions Fitting sidepanel into an installed frame Fixing decorative hardware 3D adjustable
More informationASS 70 FD folding/sliding door installation guide
ASS 70 FD folding/sliding door installation guide 2 Preparation IMPORTANT These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the
More informationInstallation Guide. WarmCore. Folding Sliding door system. Glass Packing. Pre-Installation. Removing the Existing Door.
WarmCore Installation Guide Pre-Installation Glass Packing p5 Removing the Existing Door Glazing Sequence p6 Preparing the Opening Glass Packing Locations for Toe & Heel p6 Door Alignment Sill Options
More informationPVCu FOLD & SLIDE DOOR OUTWARD OPENING
PVCu FOLD & SLIDE DOOR OUTWARD OPENING STEP-BY-STEP FULLY ILLUSTRATED ASSEMBLY INSTRUCTIONS This product is covered by a 10 year manufacturer s guarantee. Should any part of it become defective due to
More informationInstallation Instructions
Supafold Slide Aside System Three Fold Room Divider Installation Instructions Distinctive Doors Ltd Supafold Slide Aside Internal Folding System IMPORTANT: Before proceeding with the installation, and
More informationVertical Slider Section Detail
Vertical Slider Section Detail PRODUCT GUIDE Main & Bead Profiles 128 42 69 VS01 - Outer frame 150 139 210 189 60 52 52 52 48 30 42 60 18 72 90 18 60 VS02 - Cill VS14 - Cill 18 VS03 - Top Sash VS04 - Standard
More informationwindow installation TECHNICAL GUIDE Everbrite House, Greenway, Harlow Business Park, Harlow, Essex CM19 5QJ
TECHNICAL GUIDE window installation Everbrite House, Greenway, Harlow Business Park, Harlow, Essex CM19 5QJ T: 0845 4567668 F: 01279 629924 E: info@everbritedirect.com PART OF THE EVERBRITE GROUP CMS 1065*
More information1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS
1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O
More informationPatio door. Installation guide
Patio door Installation guide The following installation guide is designed to show you the best way to fit the Liniar sliding patio door. y following the details within you will be able to give your customer
More informationHow to operate (folding)
How to operate (folding) LEFT HAND STACKING OUTWARD OPENING How to operate (folding) RIGHT HAND STACKING OUTWARD OPENING LOCK BOTH LEVER HANDLE AND FLAT HANDLE UTILISING THE D-HANDLE LOCATED ABOVE THE
More informationINSTALLATION MANUAL FORTRESS SERIES
Guardian Security Structures TEL 1-406-212-2334 EMAIL rg@gssdoors.com WEB www.gssdoors.com FORTRESS SERIES GENERAL INSTALLATION GUIDELINES 1. The door frame is installed using 16 bolt screws 7,5 mm in
More informationVanity Installation Instructions
Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation
More informationInstallatIon InstructIons for 2-lIte PatIo Door unassembled
InstallatIon InstructIons for -lite PatIo Door unassembled tools & materials You will need: Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Utility Knife High-Performance Premium Silicone
More informationTECHNOLOGY IN MOTION MACO TILT AND TURN FITTINGS. MULTI POWER fully concealed fittings INSTALLATION INSTRUCTIONS
TECHNOLOGY IN MOTION MACO multi-matic TILT AND TURN FITTINGS INSTALLATION INSTRUCTIONS Key Sash rebate height Sash rebate width Tilt-only window 50 kg Maximum sash weight 2 Contents Applications/processing
More informationICU TRACKLESS SLIDING DOOR
Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets
More informationICU TRACK SLIDING DOOR
Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and # screws Wrenches / Sockets
More informationSide Light Frame Pack Assembly Instructions
Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow the step by step guide. IDENTIFY THE PACK CONTENTS
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B PFD30 SG Fire Door Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors SUGGESTED TOOLS DRILL G-CLAMP TAPE MEASURE (Image for reference only) HACKSAW POCKET
More informationIn-line Patio Fabrication & Installation
In-line Patio Fabrication & Installation Instructions 2 Pane Patio p2 Cutting and Preparation p2 Welding and Cleaning p2 Assembly p2 Fabrication Instructions for 3/4 Pane Lock Style p3 Installation (removable
More informationSide Light Frame Pack Assembly Instructions
Side Light Frame Pack Assembly Instructions Please read this complete set of assembly instructions before starting the installation and only when you understand the construction method start to follow
More informationINSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING
JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED
More informationGROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02
GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B PFD30 Fire Door Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors IF INSTALLING A TOUCH LATCH, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS FIRST
More informationDOOR BiFOLD DOOR SET (3 + 1)
3 4 DOOR BiFOLD DOOR SET (3 + 1) Bespoke and Standard Sizes 3.6M - 3590mm W x 2090mm H 4.0M - 3990mm W x 2090mm H IB73HEP431 - ISSUE B All products must be installed in accordance with accepted good trade
More informationINSTALLATION INSTRUCTIONS FOR A&L PRODUCTS
INSTALLATION INSTRUCTIONS FOR A&L PRODUCTS AUGUST 2017 1 RECOMMENDED BUILDING IN-DETAIL Should you require further information, please contact A&L Windows on 1800 441 414 2 IMPORTANT IMPORTANT Allow Vinyl
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationWPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
More informationIF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST
Set A Set B PFD60 Fire Door Kit FITTING INSTRUCTIONS IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST SUGGESTED
More informationPortofino Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino shower enclosure. Please study these instructions
More informationFold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE
Fold-A-Way Patio Door ASSEMBLY & INSTALLATION GUIDE This instruction guide provides the minimum recommended procedures to correctly prepare the rough opening, install a fold-a-way patio door unit and apply
More informationFig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7
FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track
More informationESA-300 Full Breakout
Interior View 0 Installation Instructions For use with ESA II Controler DORMA AUTOMATICS, Inc. 94 Sherwood Drive Toll-Free: 877-67-6 DL844-00 Lake Bluff, IL 60044 Fax: 877-4-7999 Rev. /07 Tools Required:
More informationInSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled
InSTallaTIon InSTruCTIonS For 4-lITe PaTIo Door unassembled Measuring Tape Pencil Shims Drill & Drill bits: 6", 8", 5 6", 7 6" Tools & materials You Will need: Square Hammer or Mallet Level Stiff Putty
More informationASS 70.HI Lift/Sliding and Sliding Doors Installation Guide
ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide 2 Schueco ASS 70.HI Lift/Sliding and Sliding Doors Installation Guide Installation guide IMPORTANT The ASS 70.HI door should be fitted by competent
More informationSLIDING DOOR for CORNER installation ONLY - this door closes to side panel -
by KUDOS INSTALLATION INSTRUCTIONS SLIDING DOOR for CORNER installation ONLY - this door closes to side panel - Please read these instructions throughout before installing as incorrect fitting will invalidate
More informationBefore fitting door, check opening size and squareness of timber frame. The door is made smaller to give correct clearance within the frame.
Slideaway Single & Maximizer Door Gear INSTALLATION INSTRUCTIONS 11 This garage door has been designed to be as as easy as possible to use, service and automate when installed correctly. Please therefore
More informationDeauville Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B P7001 Standard Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors IF INSTALLING A TOUCH LATCH, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS FIRST
More informationINFINITE RANGE - HINGE DOOR
INFINITE RANGE - HINGE DOOR HINGE DOOR + 1 SIDE RETURN PANEL (CORNER) Please read these instructions before installing, as incorrect fitting will invalidate the guarantee-carry out each stage before moving
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationGardman Lean-to Greenhouse Assembly Instructions
Page 1 Gardman Lean-to Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free
More informationRetractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors)
Retractable Screen Installation Instructions For Vinyl and Aluminum Clad and Wood In-Swing Hinged Doors (See separate instructions for sliding doors) IMPORTANT: Please read before you begin. Table of Contents
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationFITTING INSTRUCTIONS
COMMERCIAL HINGES SECTION 2.1 SHEET 1 of 14 ISSUE: May, 2003 FITTING INSTRUCTIONS: Position and Clearances STERLING and Sterling STORM Standard Hinge Series 2.1.1 Storm Standard hinges are designed to
More informationmethod of build Komfire-75 partitioning system 75mm Steel Stud & Plasterboard Partitioning System with Square Aluminium Cover Trims KOMFORT
821 811 342 821 835 853 863 840 12.5mm Plasterboard 837 75mm Steel Stud & Plasterboard Partitioning System with Square Aluminium Cover Trims Note: For clarity the cavity infill has not been shown 854 342
More informationI n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS
I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS Page 2-9: Installation Instructions, Figures 1, 2, & 3 Page 10-12: Figures A-1, A-2, & A-3: Installation
More informationUNIT No FRAMELESS PIVOT SHOWER DOOR
INSTALLATION INSTRUCTIONS UNIT No. 3600 FRAMELESS PIVOT SHOWER DOOR NEED INSTALLATION HELP? Call 1-800-45-BASCO (452-2726) Monday - Friday 8:00 A.M. - 4:30 P.M. Eastern Time QCI0020 Rev. 3 Page 1 of 8
More informationINSTALLATION GUIDE. 1. Overview. 2. Measuring. 3. Tools & fixings you will need B C. Opening Width. Opening Height
INSTALLATION GUIDE Please take a few minutes to read through this guide before getting started. 1. Overview A Typical Sliding Wardrobe Door Layout A Frame - Top Liner (optional) B Top Track C Frame - Strike
More informationMULTI MAMMUT Heavy-duty hardware
TECHNOLOGY IN MOTION www.maco.eu ASSEMBLY INSTRUCTIONS MULTI MAMMUT Heavy-duty hardware Only for use by certified specialists! Not for end users! TILT AND TURNHARDWARE Key/abbreviations Sash rebate height
More informationSECTION side windows round corners
03-701.00/ 1 SECTION 03-701.00 2011SE08 GENERAL DESCRIPTION The windows installed on Nova vehicles may be a onepiece fixed type, or may consist of an upper and lower section, separated by a transom. The
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationPortofino Case2 Installation Guide
Portofino Case2 Installation Guide vjun16 (for 17 or 24 mm Surface Wall Profile) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino Case 2 shower enclosure.
More information3.2.3 Rear Door Window and Quarter Window Carrier Assembly
Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without
More informationGreenhouse Assembly Instructions
Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free 7 days a week on 0800
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationALLORA SWING PANEL INSTALLATION INSTRUCTIONS
ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:
More informationSliding Glass Door Assembly and Installation Guide
Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all
More informationASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL
ASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL January 2013 The SL500A is a square upright glass cabinet with a single hinged lockable door. It has five adjustable shelves plus the base. It also has an optional
More informationE N G L I S H GARDEN SHED. Assembly Instructions. Suitable for Models WITH VARYING DEPTHS
GARDEN SHED Assembly Instructions Suitable for Models 6' Wide 8' Wide 0' Wide WITH VARYING DEPTHS GI0003 November 0 INSTALLATION ADVICE It's Not That Difficult! The construction of your shed isn't as complicated
More informationHeavy Wall Applied Stop Tube Frame and Door Installation
INSTALLATION INSTRUCTIONS Heavy Wall Applied Stop Tube Frame and Door Installation Read all instructions before beginning installation. These instructions are provided to help prevent installation problems
More informationPrivacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationNARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions
NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls
More informationSTORAGE & SHELVING SYSTEM - INSTALLATION GUIDE
STORAGE & SHELVING SYSTEM - INSTALLATION GUIDE If you have ordered storage drawers, shelving, hanging rails or shoe racks this guide will help you install your storage and shelving system, together with
More informationMethod of Build 1. Fire. Sound
Method of Build 1 General Viso Fire & Acoustic in the solid form differs from most other systems as it can be erected using 12.5mm & 15.0mm boards within the same Aluminium framework. Also hidden fix board
More informationSwing Door Installation Manual
Manual 20D/35D/50D 20DH/35DH 40M/50M 25FD 35XT 50XT 01-4000-03 2010 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes.......................................
More informationAllora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED
Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating
More informationFrameless Hinged Door Enclosure. These instructions must be left with the user. Installation Guide W2-B
Frameless Hinged Door Enclosure These instructions must be left with the user Installation Guide 1 1290643-W2-B 1290643-W2-B 2 Introduction Thank you for purchasing a quality product. To enjoy the full
More informationASOLA - THETA ISTRUZIONI DI MONTAGGIO FITTING INSTRUCTIONS INSTRUCTIONS DE MONTAGE INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG. IMPBAT Rev.
ASOLA - THETA I F E D ISTRUZIONI DI MONTAGGIO FITTING INSTRUCTIONS INSTRUCTIONS DE MONTAGE INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG IMPBAT08-2 - Rev. 00 "THETA" FITTING INSTRUCTIONS SUB-FRAME Correct
More informationDeauville Installation Guide
vjul16 (for Recessed Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions carefully before
More informationFrameless Fixed Panel Slider QCI5279
Frameless Fixed Panel Slider QCI5279 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com Frameless Fixed Panel
More information3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS
3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationFrameless Fixed Panel Slider
INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need
More informationInstallation Instructions
by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...
More informationINSTALLATION INSTRUCTIONS
Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.
More informationSTACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS
STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions
More informationEASY-IN POOL STEP SYSTEM NE132
EASY-IN POOL STEP SYSTEM NE132 This instruction manual features multiple guides for the step unit components. 7939 EASY POOL STEP (NE113) FOR USE WITH: EASY-IN POOL STEP (NE126) 6492 PARTS & HARDWARE FOR
More information4-lite Patio Door. Installation Instructions
4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8
More informationCardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Cardo DOOR & RETURN SHOWER ENCLOSURE INSTALLATION PLEASE READ THESE INSTRUCTIONS CAREFULLY. IT IS RECOMMENDED TO USE A TRAINED SHOWER INSTALLER FOR THIS SHOWER TO OBTAIN THE BEST INSTALLATION. D Square
More informationInstallation Operation Care
Installation Operation Care Palm Beach Polysatin Shutters CONTENTS Getting Started Installation Overview...1 Unpacking...1 Tools and Materials Needed...1 Fasteners...2 Frame Assembly Assemble the Frame
More informationAtrium Patio Door Field Service Manual
Atrium Patio Door Field Service Manual December 2005 Table of contents Service Agreement Pg 2 Release Agreement Pg 5 Inspection form Pg 6 Warranty Pg 8 Replacing swing panel Pg 12 Replacing sliding panel
More informationVEKA GROUP PATIO DOOR PATIO DOOR PATIO DOOR UNCONTROLLED DOCUMENT AUTHOR PHIL GREGORY VEKA _IMAGINE PATIO_INSTALLER AID
VEKA GROUP VEKA _IMAGINE PATIO_INSTALLER AID UNCONTROLLED DOCUMENT VEKA GROUP USE OF THIS MANUAL Guidelines Advice & General Information. Although it is possible to manufacture a five metre four pane patio
More informationFlush Fitting Casement
The has been designed as a modern PVC equivalent of the traditional 95mm wide, flush fitting hardwood timber casement window, enabling you to replace wooden windows with authentic designs in authentic
More informationMUTO COMFORT DORMOTION XL 150/80 L 80
MUTO COMFORT DORMOTION XL 150/80 L 80 Installation instructions - Wall mount with DORMOTION ( ) TABLE OF CONTENTS Closer overall Overview Intended use Wall requirements and fittings Safety instructions
More informationContents GROUP SECTION DESCRIPTION. Page. Rapier Star SCREW FIXING GUIDE. General. General cont... General cont... Casement Window: Reinforced
Contents GROUP SECTION DESCRIPTION Page 1 GENERAL 1.1 Main Profiles Main Profiles 1 1.2 Accessory Profiles Extensions & Coupling Profiles Cills & Glazing Beads 1 2 2 FABRICATION 2.1 Sections Double Door
More informationINSTALLATION INSTRUCTIONS
Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.
More information