COMPACT 24 4 SHAFTS Savoie C. P. 4 Plessisville, Qc. G6L 2Y6
|
|
- Kristina Dean
- 5 years ago
- Views:
Transcription
1 COMPACT 24 4 SHAFTS Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX: info@leclerclooms.com On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all parts are inventoried. Check the parts received against the parts list on pages #2 to #6 of the assembly instructions. Report any discrepancies to Leclerc immediately. To assemble this loom, a minimum of 2 people are needed but it is recommended you use 3. Loom Prepared by: Inspected by: Date: * Photos: Compact 8s 1
2 1 frame with 4 shafts Pare-chocs sous cadres aminci 10½ 600 heddles 10½ 1 threading hook 1 red screwdriver & 1 Black 1 crank (Octagonal) Note for Leclerc in French : Enfiler les rondelles 3/16 dans chaque cordes et attacher par pacquet de 12 cordes. 12 treadle cords 9 with washers 1/8 X 3/ yard cord 2-10 yard cords 1 boat shuttle ( ) 1 aluminum wrench 1 adjustable wrench 2
3 1 reed 2 lease sticks 25 (metal) 2 beam sticks 24½ (metal) 2 warp rods (metal) Cable de frein 25 1/16 Installer roulettes 1 right hand side front post (with brake cable) 44 1 left hand side front post 44 1 right hand side rear post 44 1 left hand side rear post 44 1 lower rear cross-member 30½ 1 treadle cross-member 29 3
4 1 cloth beam 25 1 warp beam 28 9/16 1 thread beam 29 1/2 1 left hand side cloth beam support 1 right hand side cloth beam support with ratchet pawl 10½ 4 side post iron fittings 3 treadle blocks 2 Wood pegs ½ x 1¾ 1 take-up motion handle with 12 loop cord + 1 eyescrew LECLERC NOTE: Oeillet légèrement ouvert 4
5 2 batten swords 27¼ 6 treadles 20 1 brake treadle 20 1 treadle rod 5/16 x 30 1 batten handtree 29 1 batten sley 27¾ 1 breast beam 31 5
6 Machine bolts 1 X - 5/16 x 3 0 Carriage Bolts 2 X - ¼ x 2½ (6mm x 65mm) 2 X - 5/16 x 2¾ (8mm x 70mm) 2 X - 5/16 x 2 (8mm x 50mm) 1" Washers 4 X - 3/16 6 X - 5/16 2 X - 1/4 HEXAGON NUTS 4X- Nylon auto lock 5/16 (8mm) 2" 1½ 4 X Wooden spacer 3" Wing nuts 2 X - ¼ (6 mm) Round head screw 9 X - #14 x 2 (50mm) 8 X - #14 x 1½ (40mm) 4 X - #12 x ¾ (20mm) Nylon Wing nut for the Warp beam advance control system 1 loop cords 24" for the brake treadle 4" 1 Instruction DVD showing all stages of the installation. 4x push nuts 5/16 for treadle set rod 1 book Warp & Weave 2 black handles 2 X plastic spacers 6
7 Fix an iron fitting A on each of the 4 legs. Make sure they are positioned exactly as shown in the diagram below. Put a 3/16 (5mm) steel washer between the iron fitting and the leg. Screw them in using the 3/4 (20mm) round-headed screw No. 12. Do not over tigten so the iron can move freely. The screw must be inserted into the smallest hole of the iron fitting. Screw No. 12, 3/4 (20mm) Steel Washer 3/16 (5mm) Left rear leg Screw No. 12, 3/4 (20mm) Steel Washer 3/16 (5mm) Right rear leg ATTENTION: Application of soap to the screws will make their insertion easier. 7
8 Place the loom frame on its right side. Fix the left front A and rear B legs to the left side of the frame with a 5/16 x 2¾ (8mm x 70mm) carriage bolt. With a hammer, hit on the head of the bolt until it is even with the leg B. Cross the legs so that the lower end of the leg B is towards the back and the lower end of the leg A is towards the front. Add a steel washer and screw a 5/16 (8mm) lock nut in without overtightening it. You must feel light resistance when you swivel the legs. Left Rear Carriage bolt 5/16 x 2¾ (8mm x 70mm) Left Front Steel washer 5/16 (8mm) Nylon Lock nut 5/16 (8mm) 8
9 Lay down the frame (the bumpers must be on top) and pull on the lams C until the jacks D are parallel with the lams. Insert the left support E into the left end of the cloth beam F, then insert the take-up motion handle G and the right support H, into the right side of the cloth beam. Push all these parts between the sides of the loom and fix each support with two 1½ (40mm) round-headed screws No. 14. Bumpers Bumpers ATTENTION: Application of soap to the screws will make their insertion easier. Fig. 1 C D Screws no 14 1½ (40 mm) E F G H Heavy part on the back of the loom Make sure that the ratchet pawl is in the correct position. Fig. 2 9
10 Put a plastic spacer A in the groove as illustrated. Insert the threaded rod of the handle B. First into the front leg iron fitting C, then into the rear leg iron fitting D, then into the spacer A (fig 5). Screw the handle in the metallic plate E inside the groove and tighten it in the lower position. You have to push the plate E with your finger from the inside of the frame. Fig. 5A Place the loom on its left side and install the right front and rear legs the same way. Place the loom on its legs. 10
11 Fix the three (3) treadle blocks A to the treadle cross-member B with 2 (50mm) round-headed screws No. 14 (fig. 6). Note: Do not overtighten so blocks can move. Holes at this end of each treadle must be underneath Push nuts Assemble the treadle set as shown on figure 7. The brake treadle must be on the right side. Put one push nut on each side of the brake treadle and center it between the treadle block and the end of the treadle cross-member 11
12 Place the treadle set between the two (2) front legs by spreading them out slightly, so that the ends of the treadle rod A fit between the legs. Fix the treadle cross-member B with two (2) (50mm) round-headed screws No. 14. For installation with the wheels, use 2 flat headed screw #14 x 3 ½. Screw 2 (50mm) No
13 Brake treadle Thread one end of the loop brake cord A into the hole of the brake treadle B, then thread one end of this cord into the second loop of the other end. Pull so that it makes a knot. 13
14 Machine bolt 5/16 x 3 (8mm x 75mm) Install the warp beam A between the two (2) back posts Screw a 5/16 x 3 (8mm x 75mm) machine bolt into the brake drum B. Use the crank D to tighten the bolt firmly. 14
15 Unroll (unpack) the brake cable. Turn clockwise 3 times around the brake drum starting at the top. Join the end of the cable to the back S hook of the brake lever. Join the brake loop cord to the Back S hook using the best possible loop so the brake treadle will be at the desired height. Join the front S hook of the brake lever to the brake spring loop cord so the tension on the spring will be high enough to lock the warp beam while weaving. The warp beam should turn with some friction clockwise (while standing at the right side of the loom near the brake system) and this is the warping rotation. However, you should always release the tension on the friction brake system by disconnecting the spring from the brake lever (S hook) when you are warping the loom. To advance the fabric when weaving, depress the brake treadle just enough to release the warp beam. Depressing the brake treadle too far may cause the brake cable to come off the brake drum. 15
16 Install the thread beam (29½ ) A using round-headed screws No. 14, 1½. Install the lower cross-member B (30½ ) in back of the loom with round-headed screws No. 14, 2. For installation with the wheels, use 2 flat headed screw #14 x 3 ½. Screw 1½ (40mm) No. 14 Screw 1½ (40mm) No. 14 Back Post Screw 2 (50mm) No. 14 Screw 2 (50mm) No
17 Fix each of the two (2) batten swords A inside the front legs with a 5/16 x 2 (8mm x 50mm) carriage bolt. Place a steel washer between the sword and the leg. With a hammer, hit on the head of the bolt until the square inside part is in the wood. Put a washer inside and lock it with the nylon auto lock nut 5/16 (8mm) without overtightening it. The swords must move freely. Fix the batten sley B with two 2 (50mm) round-headed screws No. 14. Fix the batten handtree C with two 1/4 x 2 1/2 (6mm x 65mm) carriage bolts, two steel washers 1/4 and two wing nuts 1/4 (Fig 12A). 2 (50mm) Screw No. 14 Carriage Bolt 5/16 x 2 (8mm x 50mm) Carriage Bolt 5/16 x 2 (8mm x 50mm) Washers 5/16 (8mm) Nylon Auto lock nut 5/16 (8mm) Washers 1/4 (6mm) Carriage bolt 1/4 X 2 1/2 Wing nut 1/4 (6mm) Fig. 12A 17
18 Place the reed A between the batten handtree B and the batten sley C, and lower the batten handtree. Tighten the wing nuts. Using a hammer, insert a batten stopper D (round piece of wood) into each of the two (2) swords E. 18
19 Install the breast beam A with two round-headed screws 1½ (40mm) No. 14. Make sure that the hole for the eyescrew is on the right side, more instruction on next page. Front Post Hole for the eyescrew for take-up motion handle Screw 1½ (40mm) No
20 Screw the eyescrew in to the pre-drilled hole of the breast beam. Adjust the height of the take-up motion handle by changing the length of the loom cord. 20
21 Install treadle cords with the washers under the treadles as shown here Lam Treadle cord with washer Washer and knot NOTE: This loom works better when all the treadles are connected to lams with tie-up cords. Tie-up cords prevent the lams from jamming as the shafts go down. Following each tie-up, close the gate at the end of each treadle. 21
22 BEAMING On this loom, beam sticks, metal rods and cords have to be installed in place of the usual apron. Thread a 10 yard (9.2m) nylon cord through the third set of holes of the warp beam. Then thread the two cord ends through the corresponding holes of the beam stick Fig Yard Nylon Cord Warp Beam Beam Stick Continue threading the cord through the warp beam and the beam stick. Knot the cord at each end of the beam stick. Adjust the cord so that the tension and the length are the same for the whole width of the loom. Fig. 19 Cut the 5 yard (4.5m) cord in half. Use one half of the cord to lace the beam stick to the warp rod. Repeat the same operation for the cloth beam. Fig. 20 Warp Rod 1/2 of the 5 yard cord 22
23 To install the heddles you can just bend the heddle supports. To remove the shaft frames you first have to unscrew the top nut of the jack pin. It is important to leave the bottom nut as it is. Then pull up the shaft frame from the castle. We strongly recommend that you have those nuts installed at all times. Top Nut Jack Pin Bottom Nut Fig. 21 Fig. 22 TO INSTALL HEDDLES: Disconnect the center of both heddle supports of a shaft frame and take it out of the end frame by bending it. For more information, see the book supplied with the loom Warp & Weave. 23
24 Warp beam advance control system Install the Warp beam advance control system. This system will eliminate excessive warp yarn advance when releasing the brake system at cloth take-up. This friction system is adjustable and have to be released when winding the warp on. Just screw the wing nut with nylon bolt in the pre-install metal indert of the left back post. Screw in to Increase the friction or unscrew it to release. 24
25 To fold the loom, release the tension by pressing the brake treadle, then loosen the plastic handles on each side of the loom and pull these upward. Tighten the handles. The loom can fold even with fabric on it. IMPORTANT NOTE: Be carefull when closing and opening the loom. To avoir damage and insuries, NEVER completely remove the plastic handle. MAINTENANCE: In order to get the maximum efficency from your loom, we recommend you periodically spray a lubricant (silicone) on the plastic slides on each side of the loom. We at Leclerc encourage Weaver feedback on this and all our products. Please send your comments to Leclerc Loom Co. HAPPY WEAVING 25
COMPACT 24 8 SHAFTS
COMPACT 24 8 SHAFTS 1022-0001 1573 Savoie C. P. 4 Plessisville, Qc. Canada G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay out
More informationCOMPACT 24 8 SHAFTS
COMPACT 24 8 SHAFTS 1022-0001 1573 Savoie C. P. 4 Plessisville, Qc. Canada G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com nfo@leclerclooms.com On receiving the loom, unpack and lay out
More informationARTISAT 36 JACK-TYPE 8 SHAFTS
ARTISAT 36 JACK-TYPE 8 SHAFTS 1009-0008 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay
More informationCOMPACT 24 KIT 8 shaft
COMPACT 24 KIT 8 shaft 1023-0000 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the kit, unpack and lay out the
More informationNILUS II 8 SHAFTS JACK-TYPE LOOM
NILUS II 8 SHAFTS JACK-TYPE LOOM 36" 45" 60" 8 SHAFTS 1029-0008 1030-0008 1031-0008 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all parts are
More informationCOLONIAL I 4s, 8s &12s Jack type
COLONIAL I 4s, 8s &12s Jack type 45" 60" 4s 1051-0000 1052-0000 8s 1051-0008 1052-0008 12s 1051-0012 1052-0012 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing
More informationMIRA II Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX:
1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com On receiving the loom, unpack and lay out the loom components. Do NOT discard
More informationNILUS II COUNTER-BALANCED
NILUS II COUNTER-BALANCED 36" 45" 60" 1026-0000 1027-0000 1028-0000 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all parts are inventoried. Check
More information8 SHAFT KIT FOR NILUS II WITH BACK HINGE TREADLES
8 SHAFT KIT FOR NILUS II WITH BACK HINGE TREADLES 36" 45" 60" 1029-2836 1030-2845 1031-2860 On receiving the loom, unpack and lay out the loom components. Do NOT discard any packing material until all
More informationARTISAT 36" JACK-TYPE 8 SHAFTS BACK HINGE TREADLES
ARTISAT 36" JACK-TYPE 8 SHAFTS BACK HINGE TREADLES 1009-3628 On receiving the loom, unpack and lay out the loom components Do NOT discard any packing material until all parts are inventoried. Check the
More informationGOBELIN KIT 2 SHAFT FRAME 45", 60"
GOBELIN KIT 2 SHAFT FRAME 45", 60" On receiving the loom, unpack and lay out the loom components Do NOT discard any packing material until all parts are inventoried. Check the parts received against the
More informationCOLONIAL V2 8 &12s Jack type Back Hinge Treadle
COLONIAL V2 8 &12s Jack type Back Hinge Treadle 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com 8s 12s 45" 1051-0082 1051-0122
More informationDOROTHY 24 v SHAFT LOOM SHAFT LOOM Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX:
DOROTHY 24 v2 2410-0000 4 SHAFT LOOM 2411-0000 8 SHAFT LOOM 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 PARTS AS SHIPPED: 1 pre-assembled loom 1(2) (3) head 4 shafts
More informationDIANA 16 SHAFT COMPUTER-DOBBY
1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com Loom Prepared by: Inspected by: Date: DIANA 16 SHAFT COMPUTER-DOBBY 2120-1624
More informationDOROTHY 15 ¾ SHAFT LOOM SHAFT LOOM SHAFT LOOM Savoie C. P. 4 Plessisville, Qc. G6L 2Y6
1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 DOROTHY 15 ¾ 2110-0000 4 SHAFT LOOM 2111-0000 8 SHAFT LOOM 2112-0000 12 SHAFT LOOM PARTS AS SHIPPED: 1 pre-assembled loom
More informationSCHACHT STANDARD FLOOR LOOMTM
SCHACHT STANDARD FLOOR LOOMTM FL3109 FL3111 FL3113 FL3115 FL3121 FL3123 FL3125 FL3127 FL3310 FL3312 FL3314 FL3316 FL3322 FL3324 FL3326 FL3328 Assembly instructions LOW CASTLE LOOM IN MAPLE Find out more
More informationWOLF PUP LOOM TM & WOLF PUP LT LOOM TM
WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212
More informationBABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms
BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away
More informationASHFORD TABLE LOOM - EIGHT SHAFT 410/610/800mm 16/24/32in
INSTRUCTIONS ASHFORD TABLE LOOM - EIGHT SHAFT 410/610/800mm 16/4/3in ESTL1110016V1 Ashford Handicrafts Limited Factory and Showroom: 415 West Street PO Box 474, Ashburton 7700 New Zealand Telephone 64
More informationWOLF LOOM DOUBLE BACK BEAM
WOLF LOOM DOUBLE BACK BEAM Assembly Instructions Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 2017 Schacht Spindle Company,
More informationASHFORD TABLE LOOM - FOUR SHAFT 410/610/800mm 16/24/32in
INSTRUCTIONS ASHFORD TABLE LOOM - FOUR SHAFT 410/610/800mm 16/4/3in Ashford Handicrafts Ltd. Factory and Showroom: 415 West Street, PO Box 474, Ashburton, New Zealand Telephone 64 3 308 9087 Facsimile
More informationSpring. Instructions for assembly
Spring Instructions for assembly The parallel countermarch system... 1 Spring assembly tips and information... 3 Assembly of the Spring... 5 Maintenance... 17 Version: Spring-V5 The parallel countermarch
More informationFLOOR LOOM & WOLF LOOMS
FLOOR LOOM & WOLF LOOMS Maintenance & Warranty 36 Standard Floor Loom Baby Wolf Wolf Pup 8.10 Wolf Pup Wolf Pup LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO
More informationLoom. Métier IMPROVED! JANUARY Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: FAX:
Loom Métier 3310-0000 IMPROVED! JANUARY 2000 1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-2408 FAX: 819-362-2045 linfo@leclerclooms.com www.leclerclooms.com d:\leclerc\inst\acc\cendrel PARTS
More informationWORKSHOP DOBBY LOOM. User s Manual. 16 Workshop Dobby Loom 24 Workshop Dobby Loom
WORKSHOP DOBBY LOOM User s Manual 16 Workshop Dobby Loom 24 Workshop Dobby Loom AVL Looms 3851 Morrow Lane, Suite 9 Chico, CA 95928-8305 U.S.A. 530 893-4915 530 893-1372 (fax #) info@avlusa.com (e-mail)
More informationCRANBROOK LOOM. Assembly manual
CRANBROOK LOOM Assembly manual Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 2015 Schacht Spindle Company, Inc. 01.15 4- AND
More informationFLIP RIGID HEDDLE LOOM
FLIP RIGID HEDDLE LOOM SL2013, SL2014 SL2015, SL2016 Warping and Weaving Instructions Flip Loom shown with optional accessories Trestle Floor Stand and Flip Trap Find out more at schachtspindle.com Schacht
More informationAUTOMATIC ADVANCE MANUAL
AUTOMATIC ADVANCE MANUAL AVL Looms, Inc. 3851 Morrow Lane, Suite #9 Chico, CA 95928-8305 530 893-4915 530 893-1372 fax # info@avlusa.com www.avlusa.com Copyright 2009 TABLE OF CONTENTS Page # I. Parts.........................
More informationCreated by Penny Wakefield for ART 127
Created by Penny Wakefield for ART 127 RAISE SHAFTS & hold up with a dowel or a board Bring warp bar up over the back beam. Slip warp end onto warp bar & center. Insert lease sticks into counting cross
More informationWorkshop Dobby Loom User s Manual
Workshop Dobby Loom User s Manual Figure 1-16" Workshop Dobby Loom Figure 2-24" Workshop Dobby Loom AVL Looms 2360 Park Avenue Chico, CA 95928-6785 800 626-9615 530 893-4915 530 893-1372 (fax) http:\\www.avlusa.com
More informationWORKSHOP DOBBY LOOM. User s Manual. 16 Workshop Dobby Loom 24 Workshop Dobby Loom
WORKSHOP DOBBY LOOM User s Manual 16 Workshop Dobby Loom 24 Workshop Dobby Loom AVL Looms 2360 Park Avenue Chico, CA 95928-6785 U.S.A. 530 893-4915 530 893-1372 (fax #) info@avlusa.com (e-mail) www.avlusa.com
More informationEmilia. The Folding Rigid Heddle Loom. Learning to weave on your Emilia loom by Joanne Hall
Emilia The Folding Rigid Heddle Loom Learning to weave on your Emilia loom by Joanne Hall Heddle Handle Heddle Bracket Rigid Heddle Warping peg The Emilia Loom and Accessories Warp beam Texsolv cord Folding
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationEmilia. The Folding Rigid Heddle Loom. Learning to weave on your Emilia loom by Joanne Hall
Emilia The Folding Rigid Heddle Loom Learning to weave on your Emilia loom by Joanne Hall Heddle Handle Heddle Bracket Rigid Heddle Warping peg The Emilia Loom and Accessories Warp beam Texsolv cord Folding
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationInstallation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100
Installation instructions for FC14S Forward Controls for Shadow ACE and Aero 1100 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More informationInstallation Instructions for FC2 & FC15 Forward Controls for the Super Magna
Installation Instructions for FC2 & FC15 Forward Controls for the Super Magna It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More informationFind out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO p f
WOLF STROLLER FL3051 Assembly Instructions folded ready to travel open ready to weave For installation on Wolf Pup, Wolf Pup LT, Baby Wolf, and Mighty Wolf Looms Find out more at schachtspindle.com Schacht
More informationElectric Skein Winder
Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers
More informationThe Queen Quilter Professional Quilters Kit Frame
The Queen Quilter Professional Quilters Kit Frame Assembly Instructions Table of Contents: Before you begin......................... Pg. 2 Wood parts............................. Pg. 3 Hardware..............................
More informationwoven in color info Skill level: Easy PDF Pattern Instructions (If you can t open this PDF file you need Adobe Acrobat Reader. Get it here.
Autumn Hues woven in color info Skill level: Easy Knitting yarns gone woven. PDF Pattern Instructions (If you can t open this PDF file you need Adobe Acrobat Reader. Get it here.) Designed by Jane Patrick
More informationLumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at:
Lumber Smith Assembly Manual If you are having problems assembling the saw and need assistance, please contact us at: 804-577-7398 info@lumbersmith.com 1 Step 1 Safety Carefully read the Owners Manual.
More informationSide Winder R o u t e r L i f t.
Woodpeckers PRECISION WOODWORKING TOOLS Side Winder R o u t e r L i f t. INSTALLATION INSTRUCTIONS The wrench handle must be pointing left in order to fully insert or remove it. Lift Wrench Once fully
More informationInstructions. Assembly
Assembly Instructions The band weaving loom has a long tradition in the history of weaving in Sweden. Bands are used for many things, like the hanging tapes sewn into towel hems. Wider bands can be used
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationThe Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.
The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box
More informationBaby Grande or Grande Crank Shade with Cables and Housing Installation Instructions
Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry
More informationDurst Laborator 138 S
Durst Laborator 138 S -I- G139 Durst Laborator 138 S Durst Laborator G 139 Servicing instructions L 1 3 8 S G 139 - Replacing the counterweight spring The special tool required for this purpose is supplied
More informationELIZABETH 30 SPINNING WHEEL
INSTRUCTIONS ELIZABETH 30 SPINNING WHEEL Single and Double Treadle Ashford Handicrafts Ltd. Factory and Showroom: 415 West Street, PO Box 474, Ashburton, New Zealand Telephone 64 3 308 9087 Facsimile 64
More informationRIGID HEDDLE LOOM. Instructions for Assembly, Warping, and Weaving
RIGID HEDDLE LOOM Instructions for Assembly, Warping, and Weaving Schacht Spindle Co., Inc. 6101 Ben Place Boulder, CO 80301 303-442-3212 info@schachtspindle.com www.schachtspindle.com Rigid Heddle Loom
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationBaby Grande or Grande Crank Shade with Cables and Housing Installation Instructions
Baby Grande or Grande Crank Shade with Cables and Housing Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit Screwdriver (Flat & Phillips) Measuring Tape Pencil 4 Level Plumb Line ¼ Masonry
More information3,500/4,500lb. Vertical Cable Feighner Lift
3,500/4,500lb. Vertical Cable Feighner Lift CAUTION - PUT SAFETY FIRST 1. Before attempting to install or operate this lift, study and fully understand the proper operating procedures and safety precautions
More informationIt is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating loose.
Installation instructions for FC12 Forward Controls for Kawasaki Vulcan 750 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More informationN. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
More informationWEAVEBIRD LOOM TROUBLE SHOOTING GUIDE
1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com WEAVEBIRD LOOM TROUBLE SHOOTING GUIDE If you have problems when starting the
More informationLearn to weave. on the Knitters Loom
Learn to weave on the Knitters Loom Welcome to the wonderful world of weaving... YOUR FIRST PROJECT A SCARF You will need: A pair of sharp scissors A measuring tape Cardboard strips 20cm (8ins) wide Two
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More informationNote: this is a scanned facimile of the 1913 edition of the Weavers Delight Manual. It was created by Nancy M McKenna (c) 2000 Nancy M McKenna.
Note: this is a scanned facimile of the 1913 edition of the Weavers Delight Manual. It was created by Nancy M McKenna (c) 2000 Nancy M McKenna. As of 2000, loom parts and entire looms are available from:
More informationFLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.
More informationHAND-PAINTED RAYON RIGID HEDDLE WARP
HAND-PAINTED RAYON RIGID HEDDLE WARP Instructions / Suggestions You will need a Rigid Heddle loom that weaves at least 9 wide and a 12 dent rigid heddle bar This hand-painted rayon warp has 108 threads,
More informationThor Audi A4/S4 Skid Plate Installation Instructions
Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts
More informationOperating, Servicing, and Safety Manual Model " Foot Shear CAUTION: Read and Understand
Operating, Servicing, and Safety Manual Model 3000 52" Foot Shear CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. SAFETY The purpose of the
More informationOPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationA-Series Dobby Loom Weaving Manual
A-Series Dobby Loom Weaving Manual AVL Looms 2360 Park Avenue Chico, CA 95928-6785 U.S.A. 530 893-4915 530 893-1372 (fax#) info@avlusa.com(e-mail) www.avlusa.com Copyright 2017 All Rights Reserved Worldwide
More informationREPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
More informationBEAST THE. Tube and Pipe Notcher Operating Instructions. Notches In Bends Straight Notches. Angled Notches. Offset Notches
Copyright (c) 2007 J D SQUARED INC. www.jd2.com THE BEAST Tube and Pipe Notcher Operating Instructions Notches In Bends Straight Notches Angled Notches PATENT PENDING Offset Notches Assembly After unpacking
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationThere are a lot of small steps involved in setting up the loom. Checklists
Master Warping Checklist There are a lot of small steps involved in setting up the loom. Checklists help us stay on track. Included here are lists for direct and indirect, single and two-heddle warping
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationWeaving Your 1st Scarf
Weaving Your 1st Scarf My First Woven Scarf See part 1 How to Warp the Kromski Harp Forte to get started. Supplies: Kromski Harp Forte Loom at least 8 wide 155 yards size 3 Crochet Thread or 8/2 Weaving
More informationModel 209 Fireback Replacement
Model 209 Fireback Replacement Please read all the instructions before you begin the procedure. Confirm that you have all the necessary tools and materials. If you have any questions, technical support
More informationINSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM
INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationREPAIR INSTRUCTIONS: CABLE
The repair instructions describe replacing the Cable in the Easy Sun PARASOL Sunshade. These repair instructions are intended only for persons with experience of using the tools required. Please read the
More informationRolling Curtain door Manual
Rolling Curtain door Manual Installation Maintenance parts Model 944 PHONE 800 448 8979 FAX 800 236 8722 website www.tracrite.com EMAIL tr@tracrite.com ADDRESS 216 Wilburn Road Sun Prairie, WI 53590 This
More informationInstalling the Partridge RA Extension on Losmandy G11
Installing the Partridge RA Extension on Losmandy G11 Michael Herman July 20, 2015 Tools: 3/16 inch hex key (allen wrench) [If desired for DEC indicator ring friction improvement: flat screwdriver, and
More informationKromski Symphony Assembly Instructions
Kromski Symphony Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU
More informationLearn to weave on the. Inklette Loom
Learn to weave on the Inklette Loom THE ASHFORD INKLETTE LOOM top rear peg Inkle bands are strong and useful braids. Create colourful belts, bracelets, ties, guitar straps, shoe laces or trims for weaving.
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationKromski Prelude. Assembly Instructions
Kromski Prelude Assembly Instructions Important Notice If you have any difficulty in understanding these instructions, assembling the wheel, or having it operate to its fullest potential, WE WANT YOU TO
More informationCut-True 16M Manual Paper Cutter
Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation
More informationPower Break II Circuit Breakers
DEH40466 Installation Instructions R05 Power Break II Circuit Breakers Replacement Stop Block Kit Application This kit is provided to replace the stop block assembly in the Power Break II insulated-case
More informationHand-Painted Rayon Bouclé Scarf Warp
Hand-Painted Rayon Bouclé Scarf Warp Instructions / Suggestions You will need a Rigid Heddle Loom with a 10 dent heddle bar that weaves at least 9 wide, or a floor or table loomwith a 10 dent reed. Or
More informationBY ALIEN TECHNOLOGIES CORP
BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationQ-Zone Hoop-Frame. Assembly Instructions. Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8
Q-Zone Hoop-Frame Assembly Instructions Copyright July 11, 2018 Grace Company (Reproduction Prohibited) Version 1.8 Table of Contents Table of Contents... i Warranty... ii Parts List Box 1...iii Box 2...
More informationDepending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12
XL Quilting Frame 1 Depending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12 Foot frame Printed 2 June 2014 Updated
More information/ Rudder Installation Guide
/ Rudder Installation Guide Parts List Part # Part Description Qty Part # Part Description Qty 1030 Plastic Bead 1 1195 Rope; 1/8" Black Nylon 1 @ 9 1044 1/4-20 x 5/8" Pan Head Bolt 2 1353 Sliding Track
More informationM4 Foot Operated Underpinner Instruction Manual
M4 Foot Operated Underpinner Instruction Manual M4 Walker Rd, Bardon Hill, Coalville, Leicestershire LE67 1TU, England Tel. +44 (0)130 1692, Fax +44 (0)130 16929 e mail sales@framerscorner.co.uk M4 Underpinner
More informationNo. 412, 414, 416 Operations Manual
No. 412, 414, 416 Operations Manual CARE: Occasional oiling of moving parts with machine oil will ease operation and extend the life of the brake. Occasionally check and tighten the lower beam bracket
More informationREPLACEMENT TARP for SRT-2 SPOOL ROLL TARP
REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice. Always handle components
More informationJOY 2 SPINNING WHEEL
INSTRUCTIONS JOY 2 SPINNING WHEEL SINGLE & DOUBLE TREADLE WITH A SLIDING HOOK FLYER JASW110618V8 Ashford Handicrafts Limited Factory and Showroom: 415 West Street PO Box 474, Ashburton 7700 New Zealand
More informationthe LACIS TAPESTRY TABLE LOOM
LF11 the LACIS TAPESTRY TABLE LOOM Front Frame Bar Heddles Heddle Rod Back Frame Bar Rod Support Elastic Leg Bar Side Frame Bar Rod The LACIS TAPESTRY TABLE LOOM incorporates a novel shed changing device
More informationAX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS
AX1001 Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM 83 84 84 85/86 87 87 88 89 90 91 62 64 64 64 64 64 64 65 65 65 65 66 66 65 66 66 65 63 63 66 67 68 55 66 66 70
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:
More informationJVice Care and Maintenance Thanks for purchasing a Jvice. If properly looked after your Jvice will give a lifetime of tying pleasure.
JVice Care and Maintenance Thanks for purchasing a Jvice. If properly looked after your Jvice will give a lifetime of tying pleasure. Although it is manufactured from highest quality materials any metal
More informationOPERATIONS MANUAL. Port-O-Slitter
Tapco Products Company The World Leader in Specialty Tools for the Professional Port-O-Slitter OPERATIONS MANUAL General instructions, set up, accessories and guide to using your portable precision slitting,
More informationBrother Industries, Ltd. Nagoya, Japan
4. 2001. This service manual has been compiled for explaining repair procedures of the MODEL XL-6562, XL6452, XR- 46. This was produced based on up-to-date product specifications at the time of issue,
More informationA SERIES PRODUCTION DOBBY LOOM
A SERIES PRODUCTION DOBBY LOOM User s Manual AVL Looms 2360 Park Avenue Chico, CA 95928-6785 U.S.A. 530 893-4915 530 893-1372 (fax #) info@avlusa.com (e-mail) www.avlusa.com Copyright 2008 All Rights Reserved
More information