SIMtech 20 July OWNER Manual

Transcription

1 SIMtech 20 July 2010 OWNER Manual Multi GAMINATOR block type The author of this guidance spares large attention drafting and association of technical information, taking into account advantages of progressive supervisory mechanisms. Nevertheless, it is impossible fully to eliminate possible errors. Therefore a producer carries no responsibility, including legal, for any consequences which can arise up from incorrect positions of this guidance. An author will thank for any error diagnostics. Introduction Multi GAMINATOR block type alternative to the original programs of Gaminator on the platform of Cool Fire I. In this playing program the independent choice of version of set of slots of Gaminator is possible from I for the XXX versions, and also forming of the set is possible from the games resulted below. This product has similar graphic arts with the programs of Cool Fire I, but is not a copy or modification of multigame of Novomatic. Games of multigame Multi GAMINATOR block type: Always Hot Bananas Go Bahamas Beatle Mania Book Of Ra Columbus Dolphin s Pearl Hot Target Just Jewels Lucky Lady s Charm Magic Money Marco Polo Oliver s Bar Pharaohs Gold II Queen Of Hearts Riches Of India Roller Coaster Sharky Sizzling Hot The Money Game Ultra Hot Unicorn Magic Venetian Carnival The mathematical algorithm of work of the program is similar with original Gaminator, only that goes out on the set percent for less of games.

2 During setting any of variants of acquisition in the corps of vehicle will make sure in his normal aeration! In the case of absence of the normal cooling correctness of work of device is not guaranteed. Installation. For the feed of pay the power module is required with 24pin ATX Power Connector, by power more 100Vt. At the turned off feed of the power module will connect in turn: feed-in sockets from the power module: 24pin ATX, 4pin ATKH 12v. We connect the cord of sound and interface cord of management comptroller. On the pay of comptroller connect a feed from the power the socket of 4pin module +5V GND GND +12V. We connect the lower monitor of vehicle in the socket of VGA, in the socket of DVI overhead (take into account that an overhead monitor will work only with a digital signal, the type of cable and monitor must be expected under DVI-D!) Connect wires of keyboard of automat to the regional socket of JAMMA 72pin. Pin out table is resulted in a table in addition.

3 Game and software. How to carry out the input of credits. Management 1). Turn the key of operator briefly (an automat will be commuted in a managing menu) Active buttons: HOLD 4 - Down HOLD 5 - Enter 2). Press the active keys for an entrance in a menu ATTENDANT Active buttons: HOLD 1 - Back HOLD 4 - Down HOLD 5 Enter 3). Choose a point REMOTE IN Active buttons: HOLD 1 - Back HOLD 3-10 CREDITS HOLD CREDITS HOLD CREDITS 4). Press the necessary keys for setting of the required value of credit. 5). The chosen credit will be set automatically on a credit meter. 6). Briefly turn the key of operator. 7). An automat automatically will be commuted in the playing mode. The function of REMOTE IN can be used only, if it is included in an administrator menu.

4 How to carry out handpay payment. 1). Turn the key of operator briefly (an automat will be commuted in a managing menu) Active buttons: HOLD 4 - Down HOLD 5 - Enter 2). Press the active keys for an entrance in a menu ATTENDANT. Active buttons: HOLD 1 Back HOLD 2 Up HOLD 4 - Down HOLD 5 Enter 3). Choose a point HANDPAY CREDIT Active buttons: HOLD 1 - Back HOLD 5 - HandPay 4). Press the necessary keys for a removal and payment of the value of credit required by hand. 5). Payment by hand automatically will be registered on the meter of payments. 6). Briefly turn the key of operator. 7). An automat automatically will be commuted in the playing mode.

5 Managing menu For included in the complete administrator menu of management of owner briefly turn the key of operator, open a door FRONT DOOR SERVICE (lock the contact of 16a on earth). After the eigentone of the unclosed door once again turn the key of operator. Will appear AUDIT MENU with additional points MACHINE SETUP and ADMINISTRATION. ATTENDANT> REMOTE IN REMOTE IN: Press the necessary keys for setting of the required value of credit. CURRENT CREDIT: Shows the size of current credit. The proper cost and set credit of every payment transaction is shown. ATTENDANT> HANDPAY CREDIT HANDPAY CREDIT: Press the proper keys for the upcast of present sum. CURRENT HANDPAY: Shows the size of current credit. The proper cost and set credit of every payment transaction is shown.

6 ACCOUNTING> MASTER ACCOUNTING TOTAL IN: Lump sum of all entered bank-papers and added credits through a function REMOTE IN. BILL IN: Lump sum of the accepted bank-papers. REMOTE IN: Lump sum of all added credits through a function REMOTE IN. TOTAL OUT: Lump sum of all paid credits. HANDPAY: Lump sum of all paid credits through a function HANDPAY. TOTAL IN-OUT: Difference between TOTAL IN и TOTAL OUT. The proper cost and set credit of every payment transaction is shown. DIAGNOSTIC> PROGRAM VERSION Program version: Current version of the program. Internal version: Current version of assembling of graphic package.

7 DIAGNOSTIC> BUTTON AND LAMP TEST BUTTON TEST: Shows the real position of the button ON/OFF. For an exit from the mode of testing retain together HOLD1 and HOLD2 DIAGNOSTIC> VIDEO TEST VIDEO TEST: Used for verification of the colour modes of monitors. GAME HISTORY History of the last games is looked over in this mode.

8 GAME STATISTIC> The Money Game In this mode statistics are looked over on each of slots games. MACHINE SETUP> LIMIT SETUP CREDIT LIMIT: Set of limit value of general credit. JACKPOT LIMIT: Set of limit value of Jackpot. MACHINE SETUP> BILL/COIN ACCEPTOR SETUP PROTOCOL: Setting of type of Bill acceptor. Supported protocols: PULSE, APEX/MATRIX, CCNET, SSP, ICT, ID-003.

9 MACHINE SETUP> SET VOLLUME VOLUME: Setting of volume is in the mode of game. For diminishing of influence of hindrances on quality of sound it is recommended to put on a level 7 highest. To produce regulation of volume on the board of comptroller. ADMINISTRATION> ENTER PASSWORD ADMINISTRATION: For included in the mode of administrator enter a password. Standard value of password AAAAAAAAAA. ADMINISTRATION> CHANGE PASSWORD CHANGE PASSWORD: For the change of standard password enter in this menu. Enter a new password, will confirm Enter. You will memorize the entered password, renewal of the lost password is possible only in a service-center!

10 ADMINISTRATION> GAME SELECTOR VERSION STRING: Version, represented in the overhead right corner of basic screen of the program in the playing mode. A value can be changed on any in a limit I XXX. Game1 Game10: Games, represented on the screen. At the independent drafting of set it is possible to choose from listed above than slotovykh games. The choice of games in the menu of choice of the basic playing mode looks so: Game1 HOLD1 Game2 HOLD2 Game3 HOLD3 Game4 HOLD4 Game5 HOLD5 after changing by the START: Game6 HOLD1 Game7 HOLD2 Game8 HOLD3 Game9 HOLD4 Game10 HOLD5 MULTIGAME VERSION: Versions, proper the set of original versions of games Cool Fire I Novomatic. Changing the value of this point, the sets of games change automatically Game1 Game10 and version number in the corner of basic playing screen. ADMINISTRATION> INITIALIZATION DENOMINATION: Setting of credit cost is in a money. MAXIMUM BET PER ROW: Setting of maximally possible rate on a line. KEY INPUT: Setting of permission of raising of credit from the key. CHANGE PASSWORD: Changing of password with a menu INIT.

11 After setting of necessary parameters will turn off an automat and will include in 10 seconds after a shutdown. Tuning will be saved. Connecting of bill acceptor on protocol General information Recommended type of bill acceptor: Mfl-0386 (validation head Mflv-2110, power interface Flp-1710). Such bill acceptor (with power interface 1710) unites with a block the special interface cable, containing the microcircuit of concordance of levels of informative signals. Bill acceptor with power interface 2810 unite with a block an interface cable without the microcircuit of concordance (power interface 2810 corresponds standard com-port of block). Pin out of bill acceptor connector Appearance Setting of conclusions Contact Setting V 2 M.RES V (INTERFACE) 4 GND 5 LED+ 6 NC 7 GND 8 TXD 9 RXD 10 NC 11 LED- 12 NC Setting of conclusions # of pin Name Type of signal Data type 1 DCD IN Data carrier detect 2 RxD OUT Transmit data 3 TxD IN Receive data 4 DTR OUT Data terminal ready 5 GND - Ground 6 DSR IN Data set ready 7 RTS OUT Request to send 8 CTS IN Clear to send 9 RI IN Ring indicator

12 I will eat away on a system board RRXD1 DDTR#1 DDSR#1 CCTS# TTXD1 DDCD#1 RRI#1 RRTS#1 GND Accordance of socket on a system board an external socket Pin on MotherBoard Pin of out connector 1 (DDCD#1) 1 (DCD) 2 (RRXD1) 2 (RxD) 3 (TTXD1) 3 (TxD) 4 (DDTR#1) 4 (DTR) 5 (GND) 5 (GND) 6 (DDSR#1) 6 (DSR) 7 (RRTS#1) 7 (RTS) 8 (CCTS#1) 8 (CTS) 9 (RRI#1) 9 (RI)

13 Connection of kupyuropriemnika (power interface 1710) with block. For connection the done interface cable is used from bill acceptor ICT A7. Below on a picture chart of connecting of interface cable and feed to the socket. ATTENTION! I will eat away bill acceptor represented from the side of wires. Black White Slant 1 Interface Cable GND +5 V +12 V Blue Red ATTENTION! On some models of interface cable a feed is required +12 volt in place of +5A. Setting of wires of interface cable of Pin1 GND Blue Pin2 TXD2 Pin3 RXD2 Pin4 Program Pin5 Reset Pin6 VCC Red Pin7 RXD1 Black Pin8 TXD1 White Note: For any connecting of other bill acceptor on protocol it is possible to use the that interface cable of A7. For this purpose a socket retires for ICT A7, a socket for a feed and reducer is added for the necessity of bill acceptor. Connecting of bill acceptor is possible on the impulse of see 72-pin connector. In a menu the necessary tuning get out for bill acceptor. For the maintainance of information it is necessary to carry out a restart by the shutdown of feed.

14 Addition 1 JAMMA 72pin connector pin Part Side Solder Side 1a 1b 2a 2b 3a SPEAKER 3b GND 4a HOLD1 SW 4b BILL ACCEPTOR (PULSE) 5a HOLD 2 SW 5b 6a HOLD 3 SW 6b 7a HOLD 4 SW 7b 8a HOLD 5 SW 8b 9a START SW 9b 10a BET ONE SW 10b 11a SELECT GAME SW 11b 12a AUTO START SW 12b 13a 13b 14a MAXBET SW 14b 15a INFO SW 15b 16a FRONT DOOR (SERVICE) SW 16b 17a 17b 18a 18b 19a 19b 20a KEY ATTENDANT SW 20b 21a COLLECT SW (PAYOUT BUTTON) 21b 22a 22b 23a 23b SELECT GAME LAMP 24a 24b WBA LED 25a REMOTE&BILLS COUNTER 25b UPPER LAMP BLUE 26a GAMES COUNTER 26b UPPER LAMP WHITE 27a HANDPAY COUNTER 27b WIN COUNTER 28a 28b BET COUNTER 29a HOLD 1 LAMP 29b BET ONE LAMP 30a HOLD 2 LAMP 30b MAXBET LAMP 31a HOLD 3 LAMP 31b COLLECT LAMP 32a HOLD 4 LAMP 32b 33a HOLD 5 LAMP 33b AUTO START LAMP 34a START LAMP 34b INFO LAMP 35a 35b 36a GND 36b GND SW - switch, the button of vehicle is connected to the pay of controller through a socket JAMMA 72pin. LAMP a lamp is proper the button of vehicle. COUNTER outputs of meters. FRONT DOOR (SERVICE) SW normally-opened contact of door, if a door is opened connected to the GND.