200200C Owner s Manual
|
|
- Terence Douglas
- 5 years ago
- Views:
Transcription
1 Owner s Manual C Coin Counter & Sorter
2
3 TABLE OF CONTENTS 1. Product Views Front and Rear Views Display 2. Operation Modes Counting Mode Power Saving Mode Batch Mode Coin Tube Attachments 3. Troubleshooting Error-Message Display Codes 4. Specifications 5. Safety/Warnings Cleaning the Machine Maintenance Notice 6. Warranty Page
4 1. PRODUCT VIEWS C Front and Rear Views Control Panel 2. Coin Hopper 3. Coin Trays 4. Coin Tubes 5. Handle 6. Coin Access Panel 7. Power Button
5 1. PRODUCT VIEW Display 5 6 PRINT 7 1 BAT SET CLEAR Start/Stop Key 2. Clear Key 3. Set Key 4. Batch Key 5. (Minus) Key 6. + (Plus) Key 7. Print Report Key 3
6 2. OPERATION MODES C COUNTING MODE 1) Remove all uncounted coins from the machine during the previous count 2) Batch amounts need to be a "0" for each denomination a. Press "Set" key to view batch amounts by denomination b. Press "Clear" key to set the 0.01 (penny) to 0 c. Press "Set" key to move arrow down to next denomination d. Continue steps b and c above until all denominations are set to "0" 2) Place the coins into the hopper and press the "Start/Stop" key 3) The machine will start counting while sorting the coins 4) The machine will stop automatically when all coins in the coin hopper are counted 5) You can add more coins and the totals will continue from the last count or press the "Clear" key to reset POWER SAVING MODE The machine will enter sleep mode after 5 minutes. It can be returned to working mode by pressing any key. 4
7 2. OPERATION BATCH MODE This mode allows you to batch a specific quantity of each coin denomination. Standard batch quantities for coin rolls: Coin Batch Amount Pennies 50 Nickels 40 Dimes 50 Quarters 40 Dollars 25 Custom batch quantities: 1) Press "Set" Key to view batch amounts by denomination 2) Press "Batch" Key to raise the batch amounts by the following increments: for each "Batch" key pressed for each "Batch" key pressed for each "Batch" key pressed for each "Batch" key pressed for each "Batch" key pressed 3) Press "-" or "+" key to increase amount by 1 lower or higher 4) Press "Set" key to move to the next denomination 5) Continue steps 2-4 until all batch denominations are set 6) Place the coins into the hopper and press the "start/stop" key 7) The machine will start counting while sorting coins 8) The machine will stop automatically when the batch quantity for the denomination is reached 5
8 2. OPERATION (CONTINUED) C Coin Tube Attachments The coin tube attachments allow you to sort coins directly into standard, paper roll wrappers. 1) Remove the coin tray(s) 2) Insert wrapper into the coin tube with the crimped end down. Make sure the top of the wrapper is below the top of the coin tube 3) Slide coin tube(s) into the proper coin slot 4) Set the coin roll batch quantities see Batch Mode 5) Load coins into the hopper and press the start/stop key 6) When the selected amount of coins is obtained, the unit will stop. Remove the full tube and repeat steps 2 & 3 above 7) Press the "Start/Stop" key to continue 6
9 3. TROUBLESHOOTING Error-Message Display Codes Error Code Meaning Remedy E1 - E8 Counting sensor error Clean the counting sensor E9 Coins remaining in the machine Remove remaining coins from the machine E10 Motor detecting sensor error Make sure 2 screws for motor sensor are in and in alignment 7
10 4. SPECIFICATIONS C Specifications Dimensions: 14.2" x 11.1" x 13.4" (W x H x D) Weight: Counting Speed: 9.3 lbs 345 coins/min Power Consumption: Maximum 45W Power Source: 110VAC / 60 Hz Control Panel Screen Size: 1.5" x 2.75" Hopper Capacity (Pennies): 1,650 8
11 5. SAFETY/WARNINGS Cleaning the Machine Warning: Before doing any cleaning, turn the power switch off and disconnect the power cord. 1. External: a) Using a compressed air duster or soft cloth, clean all external parts of the machine. Do not use cleaning solvents. 2. Internal a) Remove 3 external screws around the housing b) Carefully lift up housing and make sure not to disturb connected wires c) Using a compressed air duster or soft cloth, clean the sensors and other dirty parts d) Set the housing back on the unit, make sure internal wiring is not exposed and power button is aligned 9
12 6. WARRANTY C Maintenance Notice 1) Do not put fingers inside the coin hopper or channel when the machine is in operation 2) The machine must be safely connected to the power source 3) The machine must be used and kept in dry location. Do not operate in high temperatures, humidity or smoke 4) Only use supplied power cord 5) Do not start the machine with the coin access panel open 6) Do not open the coin access panel when the machine is working 10
13 Warranty STEELMASTER provides a limited, one-year replacement warranty for this unit (200200C). This warranty is limited and conditional as the following: One-year from the date of original purchase. Applies only to the original purchaser. All warranty claims must be accompained by the proof of purchase. Warranty is limited to defects in workmanship or material. It does not apply to damages in handling the product, general misuse, poor maintenance or shipping. Warranty liability does not extend or cover any loss, harm or damages from miscounts or failures in coin counting. Warranty does not guarantee the absolute accuracy of the unit in all environments and conditions. The warranty allows for the replacement of this or similar unit within the warranty period only and STEELMASTER discretion. All warranty returns must be authorized in writing and proper approved forms included in the prepaid return package. All approved warranty returns need to be returned to: Block, Inc.; MMF Division 1111 Wheeling Road Wheeling, Illinois USA Customer Service/Support
14 FEATURES Notes C 12
15 FEATURES Notes 13
16
С 800 CASSIDA C 800 HIGH SPEED COIN COUNTER
С 800 CASSIDA C 800 HIGH SPEED COIN COUNTER This manual contains important information on safety measures and operational features. Please read it carefully before operating your coin counter, and keep
More informationUSER MANUAL ENGLISH 1450 COIN COUNTER & SORTER
USER MANUAL ENGLISH 1450 COIN COUNTER & SORTER INTRODUCTION ENGLISH Thank you for purchasing the Safescan 1450 coin counter and sorter. For proper use and maintenance, we advise to read this user manual
More informationCashConcepts CCE 4000
CashConcepts CCE 4000 Coin Counter and Sorting Machine User Manual Introduction Thank you for choosing the CCE 4000. This coin counting and coin sorting machine is designed to simplify the daily cash or
More informationModel S-520 Coin Counter / Sorter Operating Manual
Model S-520 Coin Counter / Sorter Operating Manual Table of Contents Using the Product Safely... 2 About the Warning Stickers and Points of Warning/... 2 Warning.... 3. 4 Names of the Main Parts......
More informationCOIN COUNTER & SORTER
MANUAL SAFESCAN 12 COIN COUNTER & SORTER www.safescan.com 1 INTRODUCTION Thank you for purchasing the Safescan 12 Coin Counter and Sorter, a product of outstanding ease-of-use and quality. The Safescan
More informationUSER MANUAL SAFESCAN 2210 / 2250 BANKNOTE COUNTER. 1
USER MANUAL SAFESCAN 2210 / 2250 BANKNOTE COUNTER www.safescan.com 1 ENGLISH INTRODUCTION Thank you for purchasing a Safescan 2200-series banknote counter. This user manual will help you to get started
More informationOperation Instructions
High Speed Coin Counter With Automatic Hopper Operation Instructions Content 1. Introduction. 3 2. Whole Machine Figure. 3 3. Technical Specifications 4 4. Key Panel..4 5. Precautions 5 6. Operation Procedures..6
More informationCS-10S User Manual. Coin Counter
Coin Counter CS-10S User Manual Contents 1. General Information...1 2. Diagram... 1 3. Technical specification...2 4. Panel...3 5. Operation...4 5.1 General counting mode...4 5.2 Accumulative counting
More informationOperating Manual And Service Information
Operating Manual And Service Information Coin Counters - Models CM, CE, CECR, KK, CMB, CEB, D2, and DE Please read these operating instructions carefully. They are brief but very important. Please complete
More informationMoving money forward. CASSIDA TillTally + TillTally Elite Money Counting Scales
Moving money forward CASSIDA TillTally + TillTally Elite Money Counting Scales Table of contents: 1. INTRODUCTION 1.1 About the Cassida TillTally 2 1.2 Box contents 2 1.3 Front and rear views 3 1.4 Display
More informationApexDesk Assembly Guide
ELECTRIC HEIGHT-ADJUSTED SIT TO STAND DESK ApexDesk Assembly Guide REV-1507C Table of Contents CAUTION, USE & LIABILITY... 3 PARTS & HARDWARE LIST... 4 PARTS / COMPONENT DIAGRAMS... 5 ASSEMBLY INSTRUCTIONS...
More informationCM3000. Operator s Manual. ChangeMaker. Seaga Manufacturing, Inc. 700 Seaga Drive Freeport, IL USA
CM3000 ChangeMaker Operator s Manual Seaga Manufacturing, Inc. 700 Seaga Drive Freeport, IL USA 61032 www.seagamfg.com INTRODUCTION Congratulations on the purchase of your new ChangeMaker. This ChangeMaker
More informationCOIN COUNTER & SORTER
COIN COUNTER & SORTER ADVANTAGE: Large Blue LCD display Fast counting speed of 600 units per minute Large Hopper capacity of 1000-1300 units of coins RH-850 is high technical product with light, electronic
More informationLD8000 Series LD8025 LD8050 LD8100
LD8000 Series LD8025 LD8050 LD8100 CONTENTS Read this user s manual before use to ensure proper operation. Keep the manual on hand for reference in case there is a problem. Warranty Information Maintenance
More informationFD 125 Large-Format Card Cutter
FD 125 Large-Format Card Cutter 3/201 OPERATOR MANUAL Page 2 Table of Contents SAFETY PRECAUTIONS... 4 Introduction... 5 Specifications... 5 Accessories... 5 Major Components and Assemblies... 6 Control
More informationInstallation Operation Care
Installation Operation Care Designer Roller and Designer Screen Shades Standard and Cassette Cordless Lifting System CONTENTS Getting Started: Product Views... 1 Tools and Fasteners Needed... 3 Installation
More informationThe Electric Kangaroo Pro
The Electric Kangaroo Pro WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY AND
More informationHeritage Solar Lamp Post
Heritage Solar Lamp Post Instruction Manual 23108 Thank you very much for choosing a Nature Power product! For future reference, please complete the owner s record below: Model: Purchase Date: Save the
More informationBefore Installation, Re-installation, or Troubleshooting:
The Electric Elite WARNING: FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY AND PROPERTY
More informationFD 1202 AutoSeal Tabletop Pressure Sealer
FD 1202 AutoSeal Tabletop Pressure Sealer 4/2015 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE SPECIFICATIONS 1 UNPACKING, COMPONENTS 2 SET-UP 3 OPERATION 5 DETERMINING FOLD TYPE 6 ADJUSTING
More informationBoink Kiosk System Administration Manual
Boink Kiosk System Administration Manual Last updated on May 21st, 2002 Table of Contents INTRODUCTION Boink Kiosk System...2 Safety Precautions...3 KIOSK SYSTEM NORMAL OPERATION SF6 Kiosk General Description
More informationMBM 307A / 407A PF Automatic Folders
MBM 307A / 407A PF Automatic Folders Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com OPERATION MANUAL MBM 307A / 407A AUTOMATIC FOLDERS 1-800-223-2508 www.mbmcorp.com
More informationStep 1. Setting Up the Machine. Removing the Protective Parts. Attaching the Control Panel. Loading Paper
Step 1 Setting Up the Machine 1 Removing the Protective Parts 2 Press and slide the paper guide to fit the paper width. 1 Remove the protective tape and paper. DO NOT connect the USB cable. Connecting
More informationAMP-12 OPERATOR S MANUAL
AMP-12 OPERATOR S MANUAL Version 1.0 Copyright 2002 by Vatell Corporation Vatell Corporation P.O. Box 66 Christiansburg, VA 24068 Phone: (540) 961-3576 Fax: (540) 953-3010 WARNING: Read instructions carefully
More informationHinge Boring/Insertion Machine Set Up And Operation Instructions
Hinge Boring/Insertion Machine Set Up And Operation Instructions Manufactured In The USA By: Thompson Industries, Inc. 1018 Crosby Avenue, Sycamore, IL. 60178-0127 Ph:815-899-6670 Fax:815-899-1918 Thank
More informationRead this user s manual before use to ensure proper operation. Keep the manual on hand for reference in case there is a problem.
LD3500 Series CONTENTS Read this user s manual before use to ensure proper operation. Keep the manual on hand for reference in case there is a problem. Warranty lnformation Maintenance Exploded View Features
More informationCANARY AUDIO. Power Amplifier CA-309 OWNER S MANUAL. Handcrafted in California MADE IN USA
CANARY AUDIO 300B Push-Pull Parallel Power Amplifier Mono Block Handcrafted in California CA-309 OWNER S MANUAL MADE IN USA Dear Customer: Please allow us to take this opportunity to thank you for purchasing
More informationINSTALLATION INSTRUCTIONS ROLLER SHADES
INSTALLATION INSTRUCTIONS ROLLER SHADES Tools Required: Tape measure, pencil, drill, drill bits, screw driver, step stool or ladder. Note: use a 5/64 drill bit to pre-drill the screw holes (for attachment
More informationCANARY AUDIO. EL34 Stereo Power Amplifier. Handcrafted in California CA-770 OWNER S MANUAL MADE IN USA
CANARY AUDIO EL34 Stereo Power Amplifier Handcrafted in California CA-770 OWNER S MANUAL MADE IN USA Dear Customer: Please allow us to take this opportunity to thank you for purchasing this CANARY AUDIO
More informationAXIS ELECTRIC HEIGHT ADJUSTABLE DESK Installation Guide (For 1500mm wide desk)
AXISELECTRIC HEIGHT ADJUSTABLE DESK Safety and Warnings This table complies with the prescribed safety regulations. Inappropriate use may cause damage to persons and table. Please read the operation manual
More informationTHANK YOU FOR PURCHASING OUR STUDIO RTA CREATION STATION
THANK YOU FOR PURCHASING OUR STUDIO RTA MODEL# 20672 IF YOU REQUIRE ANY ASSISTANCE WITH ASSEMBLY, PARTS, OR INFORMATION ON OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE: www.studiorta.com OR CALL OR WRITE THE
More informationFlat Sheer Shade owner's handbook
Flat Sheer Shade owner's handbook INSTALLATION INSTRUCTIONS Step 1. Check Package Contents Mounting hardware kit includes the following: Part a.mounting Brackets Quantity 2 for shades up to 45 wide 3 for
More informationAutoSeal FD 1506 Plus / FE 1506 Plus
AutoSeal FD 1506 Plus / FE 1506 Plus FK / FL SERIES 06/2018 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS DESCRIPTION 1 UNPACKING AND SET-UP 2 CONTROL PANEL 3 OPERATION 3 FOLD PLATE ADJUSTMENT 4 SETTING
More informationVigilant Reliance Series Display Cabinet. Owner s Manual
Vigilant Reliance Series Display Cabinet Owner s Manual Models: 1000, 1500, and 2000 RELIANCE SERIES CIGAR HUMIDOR DISPLAY CABINET Owner s Manual Congratulations! You ve purchased one of the finest, most
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More informationimpact VC-500LR Monolight INSTRUCTIONS
impact lighting equipment and accessories VC-500LR Monolight INSTRUCTIONS Congratulations on your purchase of the Impact VC-500LR Monolight. We feel that it will contribute much to your photographic skill
More informationeflex 75x/300x Digital Microscope with Flexible Neck User Guide
eflex 75x/300x Digital Microscope with Flexible Neck User Guide Table of Contents Important information... 4 Product description... 4 Computer requirements... 5 Windows based PC... 5 Mac OS based PC...
More informationSTRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved
6002 STRINGING MACHINE OWNER'S MANUAL Issue 3 - June 20, 1998 Copyright 1998 GAMMA Sports - All Rights Reserved 6002 OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3... ASSEMBLY
More informationUser s Guide. Model MA A AC Mini Clamp-on Meter
User s Guide Model MA150 200A AC Mini Clamp-on Meter Introduction Congratulations on your purchase of Extech s MA150 AC Mini Clamp Meter. This meter is shipped fully tested and calibrated and, with proper
More informationMAXIMIST HVLP TANNING SYSTEM
L0941 12 10:Layout 1 16/12/10 09:03 Page 1 MAXIMIST HVLP TANNING SYSTEM DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions
More informationWARNING: Do not work around outlets while the power is on. Do not stick fingers or tools into an electrical box while the power is on.
Instructions for SnapRays Guidelights WARNING Failure to turn OFF electrical power prior to installation of the Guidelight can result in electrical shock, fires, and/or death. www.snappower.com CAUTION:
More informationUSER'S MANUAL DMR-6700
USER'S MANUAL Multimeter True RMS DMR-6700 CIRCUIT-TEST ELECTRONICS www.circuittest.com Introduction This meter measures AC/DC Voltage, AC/DC Current, Resistance, Capacitance, Frequency (electrical & electronic),
More informationUPLIFT Height Adjustable Standing Desk 3-Leg (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE
UPLIFT Height Adjustable Standing Desk 3-Leg (T-Frame) DIRECTIONS FOR ASSEMBLY AND USE CAUTION MAKE SURE NO OBSTACLES ARE IN THE DESK S PATH AND ALL CORDS ARE OF APPROPRIATE LENGTH FOR DESK TRAVEL. FAILURE
More informationOPERATION MANUAL MBM 207M MANUAL FOLDER
OPERATION MANUAL MBM 207M MANUAL FOLDER 1-800-223-2508 www.mbmcorp.com 1 Safety Instructions Definition of Symbols and Notes The following names and signs stand for possible dangers: Danger This symbol
More informationStaticmaster Model 6110 Air Assist Bar Ionizer
/ Operation / Maintenance Staticmaster Model 6110 Air Assist Bar Ionizer Contents Precautions 1. Features and Descriptions 2. 3. Maintenance 4. Wire Markings 5. Specifications 6. Dimensions 7. Warranty
More informationUNIVERSAL STAND. Owner s Manual. Visit us on the web at QUESTION Model No. UT1002
Owner s Manual Model No. UT1002 UNIVERSAL STAND QUESTION... 1 877 393 7121 Visit us on the web at www.southerntechllc.com You will need this manual for safety instructions, operating procedures, and warranty.
More informationINSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER
INSTRUCTION BOOKLET AND WARRANTY INFORMATION 6 BENCH GRINDER Part No.: SW1250 PLEASE READ CARE AND SAFETY INSTRUCTIONS BEFORE USE SPECIFICATIONS Part No.: SW1250 Input Voltage: 240V Frequency: 50Hz Rated
More informationMUSICA C101 preamplifier
User manual MUSICA C101 preamplifier 1 Thank you of purchasing this EamLab product. Who are dedicated to the policy of creating the highest quality audio components, are proud to introduce. You can be
More informationInstallation Instructions HighRock 4x4 TM
Installation Instructions HighRock 4x4 TM Slider Step Vehicle Application: Jeep CJ Wrangler 1976 1986 Part Number: 49311 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question.
More informationOwner s Manual.
P Z R 6 0 0 A m p l i f i e r P Z R 1 0 0 0 A m p l i f i e r Owner s Manual www.pyleaudio.com Your New Pyle Pro PZR series P.A. Amplifier gives you the power and versatility you need in a professional
More informationATD AMP Variable Speed Reciprocating Saw Owner s Manual
ATD-10535 7 AMP Variable Speed Reciprocating Saw Owner s Manual Manufactured in China To ATD Tools, Inc. Specifications TECHNICAL SPECIFICATIONS Voltage: 120V Frequency: 60Hz Power input: 7 Amps No load
More informationEnglish User's Guide
User's Guide Imacon Flextight 343 2 2003 Imacon A/S. All rights reserved. Imacon Flextight 343 User's Guide, Part No 70030009, revision B. The information in this manual is furnished for informational
More informationVanity top, faucet and drain not included. 1-3/8 screws (x 2) (for middle and bottom drawers) Knobs (x 5)
ASHWELL VANITY BASE INSTALLATION INSTRUCTIONS Nutmeg models: 30176, 30177, 30178, 30179 Dark chocolate models: 30183, 30184, 30185, 30186 Gray models: 30190, 30191, 30192, 30193 Matte white models: 30197,
More informationUSER S MANUAL DMR-1500
USER S MANUAL DIGITAL POCKET MULTIMETER DMR-1500 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY Safety Information............................... 2-3 Safety Symbols...................................
More informationMaxiMist SprayMate Pro HVLP TANNING SYSTEM
MaxiMist SprayMate Pro HVLP TANNING SYSTEM DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions carefully and keep for
More informationInstallation Operation Care. Duette Honeycomb Shades EasyRise Lifting System
Installation Operation Care Duette Honeycomb Shades EasyRise Lifting System CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Owner s Manual Models: Sentinel 500, 1000 and 1500 VIGILANT SENTINEL CIGAR END TABLE Owner s Manual Congratulations! You ve purchased one of the finest, most accurate
More informationFORMAX. FD1500 AutoSeal OPERATOR MANUAL FIRST EDITION
FORMAX FD1500 AutoSeal OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS 1500 Shown with Optional Stand Page: 1. DESCRIPTION, UNPACKING AND SET UP 2. CONTROLS, OPERATION 3. FOLD PLATE ADJUSTMENT, SETTING
More informationCONTENTS. SAFETY PRECAUTIONS: Before use, read the following safety precautions
CONTENTS [1] SAFETY PRECAUTIONS: Before use, read the following safety precautions 2 [2] APPLICATION AND FEATURES 5 [3] NAME OF COMPONENT UNITS 6 [4] DESCRIPTION OF FUNCTIONS 8 [5] MEASUREMENT PROCEDURE
More informationTHANK YOU FOR PURCHASING OUR STUDIO RTA PROJECT STATION
THANK YOU FOR PURCHASING OUR STUDIO RTA MODEL# 50040 BLACK/MAPLE, 50042 PEWTER/CHERRY IF YOU REQUIRE ANY ASSISTANCE WITH ASSEMBLY, PARTS, OR INFORMATION ON OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE: www.studiorta.com
More informationNuclear Associates
Nuclear Associates 07-424 Digital Densitometer II Operators Manual March 2005 Manual No. 112111 Rev. 4 2003, 2005 Fluke Corporation, All rights reserved. Printed U.S.A. All product names are trademarks
More informationfor authorized workshops
for authorized workshops GSE2200 1. USING THIS MANUAL The instructions provided in this manual are intended for and delivered solely to authorized workshops recognized by the manufacturer, and are intended
More informationUser Guide. AC/DC Mini Clamp Meter. Model Introduction. Large 3 3/4 digit LCD display with 40 segment bargraph
User Guide AC/DC Mini Clamp Meter Model 380941 Large 3 3/4 digit LCD display with 40 segment bargraph Continuity and Frequency Measurements One touch DCA zero adjust MIN/MAX and Data Hold functions 0.9
More informationimove-f Assembly Manual (Motorized Version-M1/M2)
imove-f Assembly Manual (Motorized Version-M1/M2) 2 Table of Contents Exploded Desk Diagram Hardward & Tools Section 1: Basic Assembly of Desk Shipped KD (knock down) 3 4 5 Section 2: Attaching the Lowboard/Pedestal
More informationFD 2002IL AutoSeal System
FD 2002IL AutoSeal System 4/2017 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS DESCRIPTION 1 SPECIFICATIONS 1 UNPACKING 1 SETUP 2 Sealer Alignment Base Setup 2 Sealer Setup 2-4 Printer Alignment Base
More informationAutoSeal FD 2002/FD 2032 FE 2002/FE 2032 OPERATOR MANUAL FIRST EDITION
AutoSeal FD 2002/FD 2032 FE 2002/FE 2032 10/2012 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS SUBJECT PAGE DESCRIPTION 1 SPECIFICATIONS 1 UNPACKING 2 2000/2032 Components 2 Optional Conveyor Components
More informationOPERATION AND SERVICE MANUAL
KCM-D Coin Changer (Version of EURO coins) OPERATION AND SERVICE MANUAL 1 TABLE OF CONTENTS Chapter 1: General Information Introduction ----------------------------------------------------------------------------------------------------2
More informationP50 Thermal Printer Owner s Manual
P50 Thermal Printer Owner s Manual CARDINAL SCALE MFG. CO. 8525-M328-O1 Rev B 203 E. Daugherty, Webb City, MO 64870 USA 10/14 Ph:417-673-4631 Fax 417-673-2153 www.detectoscale.com Technical Support: Ph:
More informationScrewfeeder Troubleshooting Guide
Symptom General Cause Specific Cause Solution Illustration No Screws are being fed to the screwdriver Screw jam in screw delivery tubing Insufficient Screw Blast to deliver screw Adjust Screw Blast Inline
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T81 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More informationFD 1500 AutoSeal 12/07 OPERATOR MANUAL THIRD EDITION
FD 1500 AutoSeal 12/07 OPERATOR MANUAL THIRD EDITION TABLE OF CONTENTS FD 1500 shown with optional cabinet TOPIC PAGE DESCRIPTION, UNPACKING, SET-UP, CONTROLS 1 OPERATION 2 FOLD PLATE INSTALLATION, ADJUSTMENT
More informationModel 113 Scintillation Preamplifier Operating and Service Manual
Model 113 Scintillation Preamplifier Operating and Service Manual Printed in U.S.A. ORTEC Part No. 717560 1202 Manual Revision B Advanced Measurement Technology, Inc. a/k/a/ ORTEC, a subsidiary of AMETEK,
More informationPlease read carefuly before using. Aerobic Lateral Trainer ASSEMBLY MANUAL H901
Please read carefuly before using. Aerobic Lateral Trainer ASSEMBLY MANUAL H901 TABLE OF CONTENTS 1 IMPORTANT SAFETY INFORMATION 2 Important Safety Precautions 2 Weight Limit Capacities 2 Warning 2 2
More informationCongratulations on your purchase of Tiger s electronic JUMBLE!
Congratulations on your purchase of Tiger s electronic JUMBLE! Before you get started, here are a few things you should know to help you enjoy your game. 1 LCD SPEAKER DIRECTIONAL KEYS CLUE ON OFF RESET
More informationDOREL ASIA KITCHEN CART
DOREL ASIA Model No: WM6545N (Natural) WM6545W (White) UPC CODE: 0-65857-16525-8 (Natural) 0-65857-16526-5 (White) NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND
More informationOWNER'S MANUAL Issue 2 - December 14, 2000
OWNER'S MANUAL AL Issue 2 - December 14, 2000 Copyright 2000 GAMMA Sports - All Rights Reserved Provided by www.gssalliance.com OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...FEATURES PAGE
More informationApplication Tooling Specification Sheet
Modular Crimp Head Order No. 63811-5970 FEATURES Application Tooling Specification Sheet TYPE 4A Hand Crimp Tool Order No. 63811-5900 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically
More informationPR200DAB DAB+/AM/FM RADIO USER MANUAL IMPORTANT! WARRANTY INFORMATION INSIDE. PLEASE READ. Trademark of TEAC Corporation JAPAN
PR200DAB DAB+/AM/FM RADIO USER MANUAL IMPORTANT! WARRANTY INFORMATION INSIDE. PLEASE READ Trademark of TEAC Corporation JAPAN www.teac.com.au WARRANTY PROCEDURE v1.7b: July 2016 for 12M Replacement Please
More informationUser s Manual. Ground Resistance Clamp On Tester MODEL
User s Manual Ground Resistance Clamp On Tester MODEL 382357 Warranty EXTECH INSTRUMENTS CORPORATION warrants the basic instrument to be free of defects in parts and workmanship for one year from date
More informationOperating Instructions
TG 310CS Coin Counting - and Sorting Machine Operating Instructions Total Postweigh International Ltd. 1 Skelgillside Alston, Cumbria CA9 3TR Telephone: 01434 381182 Facsimile: 01434 382035 www.postweigh.com
More informationModels 2230 and 2240
Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform
More informationMAXIMIST ULTRA PREMIER HVLP SPRAY TANNING SYSTEM
MAXIMIST ULTRA PREMIER HVLP SPRAY TANNING SYSTEM DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions carefully and keep
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS ROTARY VANE POSITIVE DISPLACEMENT DRY-AIR PUMPS VAPOR-OIL PUMPS MADE IN AMERICA SINCE 1939 CONGRATULATIONS! You have purchased one of the most dependable and thoroughly proven Rotary
More informationAdhesive Application & Laminating System
U S E R S G U I D E Adhesive Application & Laminating System The XM2500 is an economical and easy to use document finishing system. This versatile and non-electric system has been designed to laminate
More informationTABLE OF CONTENTS WARRANTY
DM4000 CONTROL SERIES CONTROLS Instruction Manual Field Programmable Digital Tachometer for Rate and Time P.O. Box 10 5000 W. 106th Street Zionsville, Indiana 46077 Phone (317) 873-5211 Fax (317) 873-1105
More information2001A. 200KHz Function Generator Instruction Manual. 99 Washington Street Melrose, MA Phone Toll Free
2001A 200KHz Function Generator Instruction Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com WARRANTY Global Specialties
More informationMAXIMIST ULTRA PRO HVLP SPRAY TANNING SYSTEM
MAXIMIST ULTRA PRO HVLP SPRAY TANNING SYSTEM DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. Please read these instructions carefully and keep
More informationInstallation Instructions BestRail Ladder Rack Must be used with BestRail Accessories: Overhead Rack
Installation Instructions BestRail Ladder Rack Must be used with Accessories: 42791 Can be used with Accessories: 42793 Tie Down 42794 Retractable Tie Down The channels in the Ladder Rack are the same
More informationFD 340 Document Folder
FD 340 Document Folder 2/08 OPERATOR MANUAL SECOND EDITION TABLE OF CONTENTS SUBJECT PAGE DESCRIPTION 1 SPECIFICATIONS 1 UNPACKING 1 SETUP 2 CONTROL PANEL 2 OPERATION 3 SETTING CUSTOM FOLDS 4 BATCH COUNTING
More informationOPERATING AND MAINTENANCE MANUAL FLEXI MULTI-MOULDER (HAND FEED)
Enter Serial No. here. In the event of an enquiry please quote this serial number. www.monoequip.com OPERATING AND MAINTENANCE MANUAL FLEXI MULTI-MOULDER (HAND FEED) FG105 1 2 IMPORTANT NOTES FAILURE TO
More informationOWNER'S MANUAL 5 PC DINING SET DATE OF PURCHASE: NOTE: MODEL #: DASE3583 UPC CODE: RECEIPT OF PURCHASE: ATTACH HERE NEED HELP!
OWNER'S MANUAL 5 PC DINING SET MODEL #: NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION PLEASE READ AND KEEP FOR FUTURE REFERENCE. RECEIPT OF PURCHASE: DATE OF PURCHASE: ATTACH HERE
More informationStandard PS-P61 Punch Stapler
Standard PS-P61 Punch Stapler Instruction Manual Provided By http://www.mybinding.com http://www.mybindingblog.com PUNCH STAPLE PS-P61 Important Information - This manual is designed to help you to install,
More informationAutoSeal FD 2006IL / FE 2006IL
AutoSeal FD 2006IL / FE 2006IL FI / FJ Series 06/2018 OPERATOR MANUAL First Edition TABLE OF CONTENTS DESCRIPTION 1 SPECIFICATIONS 1 UNPACKING 1 SETUP 2 Sealer Alignment Base Setup 2 Sealer Setup 2-4
More informationAC/DC Clamp Meter. Owner's Manual. Model No Safety Operation Maintenance Español
Owner's Manual AC/DC Clamp Meter Model No. 82369 CAUTION: Read, understand and follow Safety Rules and Operating Instructions in this manual before using this product. Safety Operation Maintenance Español
More informationSmartphone RH/Temperature Probe Instruction Manual
Smartphone RH/Temperature Probe 800014 Instruction Manual 1 TABLE OF CONTENTS Introduction...3 Features...4 App Screen...5 Measurement Procedures...7 Care and Maintenance...14 Compatibility...14 Specifications...15
More informationPM-16 Personal Monitoring System. User Guide South D Street Fort Smith, AR
PM-16 Personal Monitoring System User Guide www.elitecoreaudio.com info@elitecoreaudio.com 920 South D Street Fort Smith, AR 72901 855-276-2673 i Important Safety Instructions WARNING: To ensure a long
More informationInstallation Operation Care
Installation Operation Care Applause Honeycomb Shades LiteRise Operating System with TrimKit Contents GETTING STARTED Product View... 1 Tools and Fasteners Needed... 2 INSTALLATION Installation Overview...
More informationInstallation Operation Care
Installation Operation Care Applause Honeycomb Shades LiteRise Operating System Contents GETTING STARTED Product View...1 Tools and Fasteners Needed...2 INSTALLATION Installation Overview...3 Mount the
More informationInstallation Instructions HOSS Hardtop Organized Storage System
Installation Instructions HOSS Hardtop Organized Storage System Application: Hard Top and Doors Storage System Part Number: 42801 www.bestop.com - We re here to help! Visit our web site and click on Ask
More informationHD-CXENVL-FDR Envelope Feeder Assembly and Operations Guide
HD-CXENVL-FDR Envelope Feeder Assembly and Operations Guide Rev. 12-12-16 1 Table of Contents DESCRIPTION OF FUNCTION... 3 Time-out (out of paper) Feature... 3 PREPARING THE HD-CX1600/1700 (C9x1) PRINTER...
More information