MX410B. Highly dynamic universal amplifier. Data sheet. Special features. Block diagram

Transcription

1 MX410B Highly dynamic universal amplifier Special features - 4 individually configurable inputs (electrically isolated) - Connection of more than 5 transducer technologies - Individual sample rates up to 100 ks per channel, 200 ks at 2 channels - 24-bit A/D converter per channel for synchronous, parallel measurements - 4 analog outputs - Real-time computation (Peak, RMS) - Supply voltage (DC) for active transducers: 5 V V Data sheet Block diagram Transducer supply Digital platform Connecting sockets D-SUB-15HD connectors IEPE 10V 20mA DC/CF TEDS A/D Electrical isolation Ethernet IEEE1588 PTPv2 FireWire IEEE1394b BNC connectors D/A Electrical isolation FireWire IEEE1394b

2 Specifications MX410B General specifications Inputs number 4, electrically isolated from each other and from supply 1) Transducer technologies per connector Strain gage, half and full bridge (carrier frequency or DC), Quarter-bridge with 1 SCM SG120/350, piezoresistive full bridge, IEPE (ICP ), Inductive half and full bridge, voltage, normalized voltage (10 V), electric voltage up to 300 V CAT II with Adapter SCM HV, normalized current (20 ma) A/D conversion 24 bit delta-sigma converter Sample rates (Domaine adjustable by software, Factory setting is HBM Classic) Decimal : ,000, adjustable for each channel ,000 in two-channel mode HBM Classic: ,000 adjustable for each channel ,000 in two-channel mode Bandwidth ( 3 ) k 38 78in two-channel mode Active low pass filter (Bessel/Butterworth, adjustable) ,000 Transducer identification TEDS, IEEE max. TEDS module distance m 100 Transducer connection D-SUB-15HD Analog outputs 4 (BNC), electrically isolated to measurement inputs and to supply (not to one another) Supply voltage range (DC) V (nominal (rated) voltage 24 V) Supply voltage interruption max. for 5 ms at 24 V Power consumption without adjustable transducer excitation W < 12 with adjustable transducer excitation W < 15 Supply voltage (active transducers) Adjustable transducer excitation (DC) V ; adjustable channel by channel Maximum output power W 0.7 per channel / 2 in total Ethernet (data link) 10Base-T / 100Base-TX Protocol/addressing TCP/IP (direct IP address or DHCP) Plug connection 8P8C-modular plug (RJ-45) with twisted pair cable (CAT-5) Max. cable length to module m 100 Synchronization options EtherCAT 4) IRIG B (B000 to B007; B120 to B127) IEEE1588 (PTPv2), NTP IEEE1394b FireWire (module synchronization, data link, optional supply voltage) IEEE1394b FireWire (only QuantumX, automatically, recommended) via CX27 via MX440A- or MX840A input channel Ethernet based Network Time Protocol IEEE 1394b (HBM modules only) Baud rate MBaud 400 (approx. 50 MBytes/s) Max. current from module to module A 1.5 Max. cable length between nodes m 5 Max. number of modules connected in series (daisy chain) 12 (= 11 hops) Max. number of modules in a IEEE1394b FireWire system (incl. hubs 2), backplane) 24 Max. number of hops 3) 14 Nominal (rated) temperature range C [F] [ ] Storage temperature range C [F] [ ] Relative humidity % (non-condensing) Protection class III Degree of protection IP20 per EN60529 Mechanical tests 5) Vibration (30 min) m/s 2 50 Shock (6 ms) m/s EMC requirements per EN Maximum input voltage at transducer socket to ground (PIN 6 or PIN 9) PIN 1, 2, 3, 4, 5, 7, 8, 10 (bridge and TEDS) V 5.5 PIN 14 (voltage) V 40 PIN 13 (current) V 1.5 PIN 4, 15 (control circuits) V ) When variable transducer supply is used, there is no electrical isolation from the supply. 2) Hub: IEEE1394b FireWire node point or distributor 3) Hop: transition from module to module/signal conditioning 4) EtherCAT is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany 5) Mechanical stress is tested in accordance with European standards EN for vibration and EN for shock. The devices are exposed to an acceleration of 50 m/s 2 within the frequency range in all 3 axes. Duration of this vibration test: 30 minutes per axis. The shock test is implemented at a nominal (rated) acceleration of 350 m/s 2 for a duration of 6 ms, half sine and with shocks in each of the six possible directions. HBM 2

3 Specifications MX410B (continued) Dimensions, horizontal (H x W x D) mm 52.5 x 200 x 122 (with case protection) mm 44 x 174 x 119 (without case protection) Weight, approx. g 990 Strain gage full bridge and half bridge 4 CF with excitation 1 V or 2.5 V or 5 V (AC, effective) Accuracy class ) Carrier frequency (sine) 4,800 2 Bridge excitation voltage (effective) V 1; 2.5; 5 (5 %) Transducers that can be connected Permissible cable length between MX410B and transducer Measuring ranges at 5 V excitation at 1 V excitation Additional shunt resistor can be connected (control signal) Strain gage and inductive full and half bridges m < 100 k % Measurement frequency range ( 3 ) ,600 Transducer impedance at 5 V excitation at 1 V excitation Noise at 25 C and 5 V excitation (peak to peak) at 1 Bessel filter at 10 Bessel filter at 100 Bessel filter at 1 k Bessel filter , , ,000 Linearity error % < 0.02 of full scale value Zero drift (full bridge with excitation 5 V) % / 10 K < ) of full scale value Full-scale drift (excitation 5 V) % / 10 K < 0.05 of measured value 1) with half bridge : 0.1 Strain gage full bridge and half bridge 4 DC with excitation 1 V or 2.5 V or 5 V or 7.5 V (DC) Accuracy class ) Bridge excitation voltage (DC) V 1 ; 2.5; 5; 7.5 (8 %) Transducers that can be connected Permissible cable length between MX410B and transducer Measuring ranges at 7.5 V excitation at 5 V excitation at 1 V excitation Additional shunt resistor can be connected (control signal) < 0.1 < 0.2 < 0.5 < 1.5 Strain gage full and half bridges m < 100 (at U B =7.5 V: < 50 m) k % Measurement frequency range ( 3 ) 0 39,300 with 96,000 sample rate 0 78,600 with 192,000 sample rate Transducer impedance at 7.5 V excitation at 5 V excitation at 1 V excitation Noise at 25 C and 5 V excitation (peak to peak) at 1 Bessel filter at 10 Bessel filter at 100 Bessel filter at 1 k Bessel filter at 10 k Bessel filter at filter Off ,000 2) (max. 50 m cable) ,000 2) ,000 2) ,000 2) < 0.15 < 0.3 < 0.6 < 2 < 9 < 10 Linearity error % < 0.02 of full scale value Zero drift (full bridge with excitation 5 V) % / 10 K < ) of full scale value Full-scale drift (excitation 5 V) % / 10 K < 0.05 of measured value 1) with half bridge : 0.1 2) Range can be modulated up to 5 k, in this case: up to 1 % absolute zero deviation 3 HBM

4 Specifications MX410B (continued) Strain gage full bridge and half bridge 100 CF with excitation 1 V or 2.5 V (AC, effective) Accuracy class ) Carrier frequency (sine) 4,800 2 Bridge excitation voltage (effective) V 1; 2.5; (8 %) Transducers that can be connected Strain gage and inductive full and half bridges Permissible cable length between MX410B and transducer m < 100 Measuring ranges at 1 V excitation Measurement frequency range ( 3 ) ,600 Transducer impedance at 1 V excitation Noise at 25 C and 2.5 V excitation (peak to peak) at 1 Bessel filter at 10 Bessel filter at 100 Bessel filter at 1 k Bessel filter , ,000 Linearity error % < 0.02 of full scale value Zero drift (full bridge with excitation 2.5 V) % / 10 K < ) of full scale value Full-scale drift (excitation 2.5 V) % / 10 K < 0.05 of measured value 1) with half bridge : 0.1 < 2 < 4 < 12 < 40 Piezoresistive strain gage full bridge and half bridge 100 DC with excitation 2.5 V or 5 V (DC) Accuracy class ) Bridge excitation voltage (DC) V 2.5; 5 (5 %) Transducers that can be connected Strain gage full and half bridges Permissible cable length between MX410B and transducer m < 100 Measuring ranges at 5 V excitation Measurement frequency range ( 3 ) Transducer impedance at 5 V excitation Noise at 25 C and 5 V excitation (peak to peak) at 1 Bessel filter at 10 Bessel filter at 100 Bessel filter at 1 k Bessel filter at 10 k Bessel filter at filter Off ,300 with 96,000 sample rate 0 78,600 with 192,000 sample rate , ,000 < 2 < 3 < 8 < 25 < 130 < 150 Linearity error % < 0.02 of full scale value Zero drift (full bridge with excitation 5 V) % / 10 K < ) of full scale value Full-scale drift (excitation 5 V) % / 10 K < 0.05 of measured value 1) with half bridge : 0.1 HBM 4

5 Specifications MX410B (continued) Voltage 10 V (DC) Accuracy class 0.03 Transducers that can be connected Voltage sensor 10 V Permissible cable length between MX410B and transducer m < 100 Measuring range V 10 Measurement frequency range ( 3 ) 0 39,300 with 96,000 sample rate 0 78,600 with 192,000 sample rate Internal resistance of the connected voltage source k < 5 Input impedance M > 10 Noise at 25 C (peak to peak) at 1 Bessel filter at 10 Bessel filter at 100 Bessel filter at 1 k Bessel filter at 10 k Bessel filter at filter Off < 100 < 300 < 600 < 3,000 < 13,000 < 15,000 Linearity error % < 0.02 of full scale value Common-mode rejection at DC common-mode at 50 common-mode > Max. common-mode voltage (to housing and supply ground) V 60 Zero drift % / 10 K < 0.02 of full scale value Full-scale drift % / 10 K < 0.03 of measured value Current 20 ma (DC) Accuracy class 0.03 Transducers that can be connected Transducer with ma current output Permissible cable length between MX410B and transducer m < 100 Measuring range ma 20 Measurement frequency range ( 3 ) 0 39,300 with 96,000 sample rate 0 78,600 with 192,000 sample rate Measuring resistance value 50 Noise at 25 C (peak to peak) at 1 Bessel filter at 10 Bessel filter at 100 Bessel filter at 1 k Bessel filter at 10 k Bessel filter at filter Off A A A A A A < 0.5 < 1.5 < 10 < 20 < 28 < 30 Linearity error % < 0.02 of full scale value Common-mode rejection at DC common-mode at 50 common-mode > 100 typically 75 Max. common-mode voltage (to housing and supply ground) V 60 Zero drift % / 10 K < 0.02 of full scale value Full-scale drift % / 10 K < 0.03 of measured value 5 HBM

6 Specifications MX410B(continued) Current fed piezoelectric transducers (IEPE Integrated Electronics Piezo Electric, ICP ) Accuracy class 0.1 Transducer technology IEPE (BNC adapter available: 1 SUBHD15 BNC) Permissible cable length between MX410B and transducer m < 30 Transducer identification (TEDS, IEEE ) only version 1.0 Transducer excitation ma 4 ma 15% Measuring ranges (AC) V 2; 10 IEPE Compliance Voltage, typ. V 21 Measurement frequency range ( 3 ) Noise at 25 C and measuring range 10 V (peak to peak) at 1 Bessel filter at 10 Bessel filter at 100 Bessel filter at 1 k Bessel filter at 10 k Bessel filter at filter Off 0 39,300 with 96,000 sample rate 0 78,600 with 192,000 sample rate < 100 < 300 < 600 < 3,000 < 13,000 < 15,000 Linearity error % < 0.1 of full scale value Common-mode rejection at DC common-mode at 50 common-mode, typically > Max. common-mode voltage (to housing and supply ground) V 60 Zero drift % / 10 K < 0.1 of full scale value Full-scale drift % / 10 K < 0.05 of output value Analog outputs Accuracy class 0.05 Number of outputs Type of connection 4 (input1 to output1 etc.) Max. cable length m < 30 Bandwidth k Defined by the input signal filter Output rate max. k 576 Nominal (rated) voltage V 10 Reference signal Common ground for all outputs, electrically isolated from supply and measurement inputs D/A converter resolution bits 16 Noise (peak to peak) mv < 10 Permissible load impedance > 2,000 / <2 nf Crosstalk attenuation > 65 Min. settling time s 120 Zero drift % / 10 K < 0.05 of full scale value Full-scale drift % / 10 K < 0.05 of output value BNC Real-time computation on the module Root-mean-square unit (RMS) 4 Peak-value unit Number of peak values Max. output rate HBM 6

7 Decimal sample rates and digital low pass filter, type Bessel (4 th order Bessel with sample rate < 100,000 ; 6 th order with sample rate= 100,000 ) Type -1 () -3 () -20 () Phjase delay *) (ms) Rise time (ms) Overshoot (%) Sample rate () 20,616 30,000 44,600 0, ,000 12,373 20,000 43, , ,000 23, , , , , , , , , , , , , *) The analog-to-digital converter s delay time is 277 s for all sample rates and has not been accounted for in the Phase delay column! Bessel Decimale sample rates : Bessel filter amplitude response , , k k k 5 k 50 2 k 10 k HBM

8 Decimal sample rates and digital low pass filter, type Butterworth (4 th order Butterworth with sample rate < 100,000 ; 6 th order with sample rate= 100,000 ) Type -1 () -3 () -20 () Phjase delay *) (ms) Rise time (ms) Overshoot (%) Sample rate () 28,269 30,000 35, ,000 18,328 20,000 26, , ,000 14, , , , , , , , , , , , *) The analog-to-digital converter s delay time is 277 s for all sample rates and has not been accounted for in the Phase delay column! Butterworth Decimale sample rates : Butterworth filter amplitude response , , k 1 k k 10 k k 20 k HBM 8

9 Decimal sample rates and digital low pass filter, (two-channel mode), type Bessel (4 th order with sample rate < 200,000 ; 6 th order with sample rate = 200,000 ) Type -1 () -3 () -20 () Phase delay (ms) *) Rise time (ms) Overshoot (%) Sample rate () 41,232 60,000 89, ,000 24,746 40,000 86, ,000 11,834 20,000 46, , ,000 23, , , , , , , , , , , *) The analog-to-digital converter s delay time is 140 s for all sample rates and has not been accounted for in the Phase delay column! Bessel Decimal sample rates and digital low pass filter, (two-channel mode), type Butterworth (4 th order with sample rate < 200,000 ; 6 th order with sample rate = 200,000 ) Type -1 () -3 () -20 () Phase delay (ms) *) Rise time (ms) Overshoot (%) Sample rate () 56,538 60,000 70, ,000 36,656 40,000 52, ,000 17,988 20,000 28, , ,000 14, , , , , , , , , , , *) The analog-to-digital converter s delay time is 140 s for all sample rates and has not been accounted for in the Phase delay column! Butterworth 9 HBM

10 Classic HBM sample rates and digital low pass filter, type Bessel (4 th order with sample rate < 96,000 ; 6 th order with sample rate=96,000 ) Type -1 () -3 () -20 () Phase delay (ms) *) Rise time (ms) Overshoot (%) Sample rate () 20,000 29,250 43, ,000 10,000 16,810 40, , , , , , , , , , *) The delay of the A/D converter is 293 s for all sample rates. it has not been accounted for in the Phase delay column! Bessel Classic HBM sample rates and digital low pass filter, type Butterworth (4 th order with sample rate < 96,000 ; 6 th order with sample rate=96,000 ) 20,000 21,700 27, ,000 10,000 11,100 15, , , , , ,000 Butterworth , , , *) The delay of the A/D converter is 293 s for all sample rates. it has not been accounted for in the Phase delay column! HBM 10

11 Classical HBM sample rates and active low pass filter sample (two-channel mode), type Bessel (4 th order with sample rate < 192,000 ; 6 th order with sample rate = 192,000 ) Type -1 () -3 () -20 () Phase delay (ms) *) Rise time (ms) Overshoot (%) Sample rate () 40,000 58,500 86, ,000 20,000 33,620 80, ,000 10,000 17,020 39, , , , , , , , , , , *) The delay of the A/D converter is 141 s for all sample rates, it has not been accounted for in the Phase delay column! Bessel Classical HBM sample rates and active low pass filter sample (two-channel mode), type Butterworth (4 th order with sample rate < 192,000 ; 6 th order with sample rate = 192,000 ) Butterworth 40,000 43,400 55, ,000 20,000 22,200 31, ,000 10,000 11,170 16, , , , , , , , *) The delay of the A/D converter is 141 s for all sample rates, it has not been accounted for in the Phase delay column! 11 HBM

12 Specifications NTX001 power pack NTX001 Nominal (rated) input voltage (AC) V (10 %) No-load power consumption at 230 V W 0.5 Nominal (rated) loading U A I A Static output data U A I A U Br (output ripple voltage; peak to peak)) V A V A mv % Current limiting, typically from A 1.6 Isolation primary secondary electrical, by optical coupler and converter Creepage and clearance distances mm 8 High-voltage test kv 4 Ambient temperature o C [ ] Storage temperature o C [ ] Accessories MX410B, to be ordered separately MX410B accessories Article Description Order No. Power AC-DC power supply / 30 W 3m cable QuantumX supply Communication Ethernet cross over cable IEEE1394b FireWire cable (module-to-module) IEEE1394b IEEE1394b FireWire IEEE ExpressCard IEEE1394b FireWire cable PC-to-module IEEE1394b FireWire cable from hub to module, IP68 IEEE1394b FireWire Extender SCM FW Input : V AC (10%), 1.5 m cable Output: 24 V DC, max A, 2 m cable with ODU connector 3 m cable for voltage supply of QuantumX modules; Suitable plug (ODU Medi-Snap S11M08 P04MJGO 5280) on one side and open strands on the other end. Ethernet cross over cable for direct operation between a PC or Notebook and a module / device, length 2 m, type CAT5+ FireWire connection cable for QuantumX or SomatXR-modules; with matching plugs on both sides. Length 0.2 m/2 m/5 m Note: The cable enables modules to be supplied with power (max. 1.5 A, from the source to the last drain). FireWire IEEE 1394b ExpressCard (ExpressCard/34) to connect QuantumX modules to a notebook or PC Firewire connection cable between module and PC. With matching plugs on both sides; Length: 3 m. No voltage supply of the modules possible via KAB293. FireWire connection cable between HUB and module. For data transfer from QuantumX modules to the HUB. Fitted with suitable plugs at both ends. Length: 3 m Package including 2 in-line elements for extension of the FireWire connection up to 40 m; Required parts: 2 x 1-KAB269-x and Industrial Ethernet cable (M12, CAT5e. No voltage supply of the modules possible via KAB NTX001 1 KAB KAB KAB KAB KAB IF002 1 KAB KAB SCM-FW HBM 12

13 Accessories MX410B, to be ordered separately (continued) Accessories MX410B Article Description Order No. Mechanic Connecting elements for QuantumX modules Connecting elements for QuantumX modules Connecting elements (clips) for QuantumX modules; Set comprising 2 case clips including mounting material for fast connection of 2 modules. Fitting panel for mounting of QuantumX modules using case clips (1 CASECLIP), lashing strap or cable tie. Basic fastening by 4 screws. QuantumX Backplane (Standard) QuantumX Backplane Standard for a maximum of 9 modules; General: Mounting on wall or control cabinet (19 ) - Connection of external modules by FireWire possible; - Power supply: 24 V DC / max. 5 A (150 W); QuantumX Backplane (Rack) Transducer side DSubHD 15 pole-to-dsub 15 pole adapter QuantumX Backplane Rack for maximum 9 modules; - 19 rack mounting with handles left and right; - Connection of external modules via FireWire possible; - Power supply: 24 V DC / max. 5 A (150 W). DSubHD 15 pole-to-dsub 15 pole adapter for connection of transducers with pre-wired DSub plug (length approx. 0.3 m); Note: Pre-wired for full bridge (6-wire). 350 ohm strain gauge quarter bridge module Signal conditioning of strain gauge quarter bridge at QuantumX full bridge input. Integrated 350-ohm completion resistor; soldering points for transducer cable (3 wire); TEDS; D-Sub-HD device connection. 120 ohm strain gauge quarter bridge module Signal conditioning of strain gauge quarter bridge at QuantumX full bridge input. Integrated 120-ohm completion resistor; soldering points for transducer cable (3 wire); TEDS; D-Sub-HD device connection. High-voltage signal conditioner DSubH 15-pol. to BNC pole adapter DSubHD 15-pole connector kit with TEDS chip TEDS-Package (10 piece) Port saver, SubHD 15 pol. High-voltage signal conditioner for differential measurement of voltages up to 300 V CAT II with type MX840A/B, MX410/B and MX440A/B QuantumX modules, with SubHD connector and fixed, 1-m-long measuring leads with 4-mm laboratory plugs. Adapter for QuantumX, BNC socket to SubHD 15 pole (pin 14), for connecting 60 V, +/10 V or IEPE / ICP ), provided that the amplifier supports this function DSubHD 15-pole connector kit (male) with TEDS chip for storage of a sensor data sheet; Housing: Metallized plastic with knurled screws. Note: The TEDS chip comes blank. Package of TESDS chips. Package of 10 1 wire EEPROM DS24B33 (IEEE TEDS) 4 x D-SUB HD 15 pin male to female port savers; protecting the wear and tear for frequent plugging and unplugging. Extends contact durability by min Adaptor attaches securely with screws 4-40 UNC. 1 CASECLIP 1 CASEFIT 1 BPX001 1 BPX002 1 KAB416 1 SCM-SG350 1 SCM-SG120 1 SCM-HV 1 SUBHD15 BNC 1 SUBHD15 MALE 1 TEDS PAK 1 SUBHD15 SAVE 13 HBM

14 Accessories MX410B, to be ordered separately (continued) Accessories MX410B Article Description Order No. Software and product packages catman AP catman Easy Complete package including catman Easy functionality plus additional modules such as integration of video cameras (EasyVideoCam), complete post-process analysis (EasyMath), automation of recurring processes (EasyScript), offline preparation of measurement projects (EasyPlan) as well as additional functions such as calculating electrical power, special filters, frequency spectrum, etc. More details at The basic software package for measurement data acquisition comprises convenient channel parameterization using TEDS or the sensor database, measurement job parameterization, individual visualization, data storage and reporting. 1 CATMAN AP 1 CATMAN EASY catman PostProcess Post Process edition for visualization, preparation and analysis of measurement data, including many mathematical functions, data export and reporting. 1 CATEASY PROCESS MX410B + catman EASY MX410B + catman AP Package including: - MX840B amplifier (1-MX840B) - Power supply (1-NTX001) - 8 transducer plugs with TEDS (1-SUBHD15-MALE) - Ethernet Cross-over cable (1-KAB239-2) - catman Easy software from HBM (1-CATMAN-EASY) - Including software maintenance for the first 12 months Package including: - MX840B amplifier (1-MX840B) - Power supply (1-NTX001) - 8 transducer plugs with TEDS (1-SUBHD15-MALE) - Ethernet Cross-over cable (1-KAB239-2) - catman AP software from HBM (1-CATMAN-AP) - Including software maintenance for the first 12 months 1 MX410B PAKEASY 1 MX410B PAKAP LabVIEW TM -Treiber 1) Universal driver from HBM for LabVIEW TM. 1 LabVIEW DRIVER CANape driver QuantumX driver for the software CANape from Vector 1 CANAPE DRIVER Informatik. CANape versions from 10.0 are supported. 1) More drivers and partners at Subject to modifications. All product descriptions are for general information only. They are not to be understood as a guarantee of quality or durability. measure and predict with confidence HBM 14 Hottinger Baldwin Messtechnik GmbH Im Tiefen See Darmstadt Germany Tel Fax info@hbm.com