Training Calendar: Year

Transcription

1 Training Calendar: Year FA Products Training Factory Automation Engineering Centre Factory Automation & Industrial Division Mitsubishi Electric India Private Limited India

2 Index 1. TRAINING CENTRES LIST OF REGULAR TRAINING COURSES FA PRODUCT TRAINING CALENDAR: YEAR REGULAR TRAINING COURSES : DETAILS... 7 FX3U PLC TRAINING... 7 HMI: GOT 2000 TRAINING... 8 Q PLC TRAINING... 9 BASIC FA NETWORK: CC-LINK TRAINING ADVANCE FA NETWORK: CC-LINK IE TRAINING MELSECNET/H TRAINING ADVANCE MICRO PLC: MELSEC IQ-F TRAINING ADVANCE MODULAR PLC: MELSEC IQ-R TRAINING SERVO BASIC - I TRAINING SERVO BASIC - II TRAINING ADVANCE SERVO: Q MOTION TRAINING AC DRIVES TRAINING SCADA: MC WORX64 TRAINING ROBOT TRAINING GOC (GRAPHIC OPERATION CONTROLLER) TRAINING FACTORY AUTOMATION BASICS TRAINING PACKAGING MACHINE HFS TRAINING PACKAGING MACHINE VFFS TRAINING CUSTOMIZED TRAINING PROGRAMMES TRAINING CHARGES AND INSTRUCTIONS FOR REGISTRATION TRAINING REQUEST FORM MITSUBISHI ELECTRIC FA CENTER GUIDE MAP

3 1. Training Centres Regular training is arranged at following centres. Pune FA Center Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, El31/15, J Block, MIDC Bhosari, Pune, Maharashtra. India Tel : Fax: Gurgaon FA Center Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, 2 nd Floor, Tower A & B, DLF Cyber Greens, DLF Cyber City, DLF Phase III, Gurgaon, Haryana. India Tel : Fax : Bangalore FA Center Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, Prestige Emerald, 6th Floor, Municipal No. 02, Madras Bank Road, (Lavelle Road), Bangalore, Karnataka. India Tel : Fax : Chennai FA Center Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, No.1 Vivekananda Road, Srinivasa Nagar Off Spur Tank Road. Chetpet. Chennai, TamilNadu. India Tel : Fax : Ahmedabad FA Center Mitsubishi Electric India Private Limited Factory Automation & Industrial Division, B/4, 3rd Floor, Safal Profitaire, Corporate Road, Prahalad Nagar, Satellite, Ahmadabad. Gujrat. India Tel : in.mitsubishielectric.com MEI-FAID-FATraining@asia.meap.com 3

4 2. List of Regular Training Courses Following training courses are regularly offered from our all training centres mentioned in previous section. Sr. No. Training Module Days Brief Courses 1 FX3U PLC 2 2 HMI : GOT Q PLC Basic FA Network CC- Link Advance FA Network : CC- Link IE MelsecNet/H Advance Micro PLC - iqf Advance Modular PLC iqr Servo Basic I 2 10 Servo Basic II 3 11 Advance Servo Q Motion 3 12 AC Drives 2 13 SCADA 3 14 Robot 3 15 GOC 2 Includes FX3U/FX3GE PLC basic & advance programming, Timer Counter & applier instructions Analog interface using blocks & ADP. Program flow control instructions like subroutine, Jump, Call, FOR- Next Loop & Indexing. Includes GOT 2000 Series HMI hardware, Screen Designing using programming software GT Designer. Alarms, Graphs, Comments, Recipe. Ladder monitoring & editing. Program diagnosis & backup using GOT Includes QnUDEH PLC hardware. Basic & advance programming using GX Works2. Timer, Counter, Applied instructions. Program booting using SD card. Analog interface. Basics of CC-Link Network, different types of devices in network, Network addressing, & connections. Master to remote & CPU to CPU interface. Network troubleshooting & CC-Link module hardware test. Basics of CC-Link IE network. CC-Link IE Field network components, topology. Network communication - Remote IO station & PLC to PLC configuration. Network diagnosis 7 troubleshooting MelsecNet/H Network range, specifications, feature. Optical loop module, coaxial bus & configuration. PLC-PLC & PLC- remote I/O communication. Link Devices & RAS function. Intelligent module at remote station. Troubleshooting Introduction to IQ-F series PLC. I/O addressing. Programming using GXWorks3. Applier instructions, timer, counter, Analog interface. Structured programming. Function block & library. Introduction to iq-r series PLC. Difference between Q & iq-r series. Comp ability in existing line. Lib. Functions, applied instructions, data labels, Analog interface, embedded data base. Maintenance & security functions Basics of servo systems, servo motor structures, Mitsubishi pulse type servo - MR JE. Servo parameter setting using MR configurator. Built in positioning using FX controller. Homing, Positioning with Modbus protocol, troubleshooting Mitsubishi's servo controller's range. SSCNet based controller & amplifier - MR-J3 & MR J4.Positining using QD77MH/77MS, M Code, QD77MS simple motion configurator, CAM design. SSCNET based servo system MRJ4. Motion CPU: Q17nD/DS, 172M/MS, SFC programming, VF/VR instructions. Motion control with virtual mode. Mechanical editor: Servo motor virtual axis Basics of Inverter, Mitsubishi FR800 series Inverter. V/F control, jogging, parameter setting. Multi-speed operation, auto tuning. CC- Link communication with FR800 inverter. Troubleshooting MC Works Architecture & featues.mx OPC server. Graph Works, Alarm server & logger. Trend server. Unified data manager. Scripting, security server. Basics of robot. Device configuration & wiring for external I/O. Robot operation & teaching. Programming with RT toolbox & teaching pendent. Robot applications & maintenance/ troubleshooting Hardware & features. Application memory & source code. Programming using CoDeSys. HMI functions, Screen designing & editing. i-key function. Modbus communication between GOC & MR-JE servo (theory) 4

5 Basics of Factory Automation Packaging Machine HFS Packaging Machine VFFS Introduction to Electro-Pneumatics, Different components- valves, cylinder, feeders, sensors. Control Components.FX3S PLC, I/O assignment, SFC programming, devices in STL, different modes of Operation - step mode execution, single cycle, continuous execution Basics of Packaging System, Introduction to Horizontal packing machine. FA Hardware selection criteria. Application development. Jogging, homing, feeder axis, Conveying, sealing, filing. Part/object missing correction logic. Troubleshooting. Basics of packing system. Vertical FFS Packing machine- hardware. FA Hardware selection criteria. Application development - Filling Systems (Auger, Pulling and sealing), Unwinding of Web, Heater control, eyemark correction, etc. Troubleshooting. 5

6 3. FA Product Training Calendar: Year Training Module Days Pune Gurgaon Bangalore Chennai Ahmedabad 4-5 Apr' Apr' Apr' May' May'16 FX3U PLC HMI : GOT 2000 Q PLC Basic FA Network CC-Link Advance FA Network CC-Link IE MelsecNet/H Advance Micro PLC - iqf Advance Modular PLC - iqr Servo Basic I Servo Basic II Advance Servo Q Motion AC Drives 2 Days 2 Days 2 Days 1 Day 2 Days 2 Days 2 Days 3 Days 2 Days 3 Days 3 Days 2 Days 1-2 Aug' Sept' Dec' Nov' Dec' Dec' Apr' Apr' Apr' May' May' Aug' Sept' Aug' Nov' Dec' Dec' Jan' Dec' Apr' May' Apr' Apr' Apr Aug' Aug' Oct' Nov' Jan' Dec' Oct' Feb'17 16 May'16 4 May'16 2 May'16 23 May'16 9 May'16 6 Sept'16 5 Oct'16 1 Aug'16 19 Dec'16 12 Sept'16 2 Jan'17 5 Dec'16 17 Oct'16 1 Mar'17 6 Mar'17 8 Feb' May' Jun' May' May' May' Sept' Sept' Aug' Dec' Sept' Jan' Dec' Oct' Mar' Mar' Aug' Jun' Sept' Jun' Jun' May' Jun' Apr' Sept' Nov' Sept' Jan' Sept' July' July' Jun' Jul' Aug' Nov' Jan' Dec' Mar' Feb' May' Apr' May' Jun' Jun' Sept' Aug' Sept' Oct' Oct' Jan' Jan' Dec' Feb' Dec' Jun' Jun' Jul' Jul' Jul' Oct' Sept' Oct' Dec' Feb' Feb' Feb' July' July Aug' Aug' Aug' Nov' Nov' Mar' Jan' Dec' Mar' Mar' May' Apr' Jun' May' May' Oct' Oct' Nov' Jan' Jan' Feb' Dec'16 SCADA Robot GOC Packaging Machine -HFS Factory Automation Basic Packaging Machine - VFFS 3 Days July' Aug' Jul' Aug' Jun' Jan' Jan' Jan' Jan' Dec'16 3 Days 6-8 Jun' May' Sept' Dec' Nov' Feb' Apr' July' Apr' Apr' Apr'16 2 Days Aug' Sept' Mar' Dec'16 2 Days 3-4 Oct' May' Feb' Oct'16 2 Days July' July' Jun' Mar' Dec' Mar'17 2 Days Nov' Mar'17 6

7 4. Regular Training Courses: Details FX3U PLC Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Two Days 09:30 am To 05:00 pm Activity / Contents 09:30 am To 01:00 pm Review of Number systems, Basics of PLC & PLC SCAN FX Series PLC Hardware Review Range of PLCs like FX3U/FX3GE, Different types of blocks/expansion modules Discrete I/O, Sourcing & Sinking, Relay & Transistor type output. PLC Memory, PLC devices & I/O Addressing PLC Programming : GX Works 2 Project creation / Project editor Transfer Setup / Upload / Download Relay Based instructions & Timer, Counters Monitoring & Editing 02:00 pm To 05:00 pm PLC Programming Grouping of bit devices, indexing registers Data Transfer instructions & Arithmetic instructions Logical / Comparison Instructions 09:30 am To 01:00 pm Analog Input & Output Block Range of analog blocks FX3U-4AD & FX3U-4DA modules Specifications, Wiring & Configuration, Interfacing with BFMs Analog Input & Output Adaptors Range of Analog Adaptor FX3U-4AD-ADP & FX3U-4DA-ADP Specifications, wiring & configuration, Special D/M Devices 02:00 pm To 04:30 pm Advance PLC Programming Jump & Subroutine Function FOR-Next Loop Instructions MC-MCR Instructions & Nesting Pointers High Speed Output PLSY & PWM Instructions 7

8 HMI: GOT 2000 Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Two Days 09:30 am To 05:00pm 09:30 am To 01:00 pm GOT Hardware review GT Designer Software New Project Creations Configuration of GOT communication with PLC OS Selection & Installation : Boot OS, Standard Monitor OS, Communication Driver Different types of Screen Various Objects like Switch/Lamps/Text & Numerical Display, Various Graphs & Other Objects. 02:00 pm To 05:00 pm GT Designer Software Part Display & Part Routes Comments/ Comment Groups/ Comment Display User Alarms: Alarm configuration & Alarm Display. Objects from Library. 09:30 am To 01:00 pm GT Designer Software Recipe Script : Project & Screen Scripts Logging Functions & Time Action Document display, Network Monitoring Backup Restoration : GOT & PLC Program 02:00 pm To 04:30 pm GT Advance PLC Programming Intelligent module Monitoring List monitor & Editor Ladder Monitoring 7 Editor One-Touch Ladder Jump Function, PLC Diagnosis with GOT Different communication options like CC-Link, Ethernet & Q Bus Connection 8

9 Q PLC Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Two Days 09:30 am To 05:00pm 09:30 am To 01:00 pm Basics of PLC Introduction of QnU/QnUDV series PLCs Hardware Discrete I/O modules, Sinking & Sourcing connections. PLC Memory drivers, Device Memory, Special Devices (SM & SD) I/O Addressing PLC Programming : GX Works 2 Simple Project Mode Transfer Setup : RS 232/USB/Ethernet Project Upload & Download Relay Based Instructions Timers & Counters Monitoring & Editing 02:00 pm To 05:00 pm PLC Programming : GX Works 2 Data Transfer Instructions Arithmetic Instructions Logical & Comparison Instructions 09:30 am To 01:00 pm Advance PLC Programming : GX Works 2 Grouping of Bit Devices & Indexing Call & subroutines, Jump, FOR-Next loop Instructions Multiple Programs File Registers Memory Card: File Register Program Backup and Booting 02:00 pm To 04:30 pm Analog Input & Output Module Programming Range of Analog Modules Connections, Buffer Memory & I/O Details BFM interface : TO/From Instructions, Un\Gm Addressing Intelligent Module Configuration AD & DA Intelligent Function Module Watch Window Direct Comments of Intelligent module Devices. 9

10 Basic FA Network: CC-Link Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Participants must have detailed knowledge of Mitsubishi Q PLC & Programming One Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm Q PLC Overview Overview of Q PLC Hardware & I/O Addressing Overview of Mitsubishi FA Networks CC-Link Network Features Specifications CC-Link Network Components Remote I/O & Analog Module Hardware & Specifications Concepts of station occupancy & allocation of devices. Data communication (Cyclic & Transient) CC-Link Network Configuration I (Remote Station Configuration) CC-Link Module configuration, Parameter setting using GX Works 2 Setting of Remote I/O station, Remote Device Station 02:00 pm To 04:30 pm CC-Link Network configuration II ( PLC PLC Configuration) CC-Link PLC to PLC communication Configuration Programming & Data transfer Diagnostics & Troubleshooting CC-Link diagnosis CC-Link Module (QJ61BT11) Hardware Test 10

11 Advance FA Network: CC-Link IE Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Two Days 09:30 am To 05:00pm 09:30 am To 01:00 pm Q PLC Overview Overview of Q PLC Hardware & I/O addressing Overview of Mitsubishi FA Network CC-Link IE Field Network Feature & Specification CC-Link IE Field Network Components CC-Link IE Network Topology CC-Link IE Field Functions Data Communication (Cyclic/Transient) CC-Link IE Network Configuration I (Remote I/O station) Remote I/O module - Hardware & specifications CC-Link IE Field Module Configuration & Parameter Setting 02:00 pm To 05:00 pm PLC Programming : CC-Link IE Fast Logic, Input Delay Function etc. Communication with L-Series Head Module. CC-Link IE Field Network Configuration- II (PLC To- PLC communication) CC-Link IE Field PLC-PLC Communication Configuration for Stand-By Master 09:30 am To 01:00 pm Diagnosis & troubleshooting CC-Link IE Field Network Diagnosis Hardware Test (QJ71GF11-T2) CC-Link IE Control Network Features & specifications CC IE Control Network Components CC-Link IE Control Network Topology. Data Communication 02:00 pm To 04:30 pm CC-Link IE Control Network Configuration CC-Link IE Control Module configuration, Parameter Setting Control Station & Normal Station Setting Communication with Other Networks Link CC-Link & CC- Link Filed. Diagnostics & Troubleshooting CC-Link IE Control Diagnosis Hardware Test (QJ71GP21-SX) 11

12 MelsecNet/H Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Two Days 09:30 am To 05:00pm 09:30 am To 01:00 pm Q PLC Overview Overview of Q PLC Hardware & I/O addressing Overview of Mitsubishi FA Network MelsecNet/H Network MelsecNet/H Module range, Specification & Features Optical loop module (QJ71P21-25, 21S-25, 21-G) Coaxial Bus Module (QJ71BR11) Configuration & wiring 02:00 pm To 05:00 pm PLC to PLC Communication : MelsecNet/H Single & Multiple Network Concept. Link devices allocation Cyclic Transmission Parameter Setting RAS function : Diagnosis & Troubleshooting 09:30 am To 01:00 pm Remote I/O Network Master & Slave Module for Optical loop & Coaxial bus Specifications & features Configuration & wiring Link devices allocation & mapping with PLC devices Module Parameter setting Intelligent module at remote station (Analog I/O) 02:00 pm To 04:30 pm Remote I/O Network RAS function ; Diagnosis & troubleshooting CC-Link Network at remote stations Intelligent module buffer memory access form master. Hardware Test for MelsecNet/H module 12

13 Advance Micro PLC: MELSEC iq-f Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Two Days 09:30 am To 05:00pm 09:30 am To 01:00 pm Introduction to iq-f Series PLC FX5 Series PLC Range Hardware & Feature I/O addressing PLC Programming : GX Works 3 Simple Ladder Programing : Project Creation & Transfer Relay Instructions, Timer, Counter 02:00 pm To 05:00 pm PLC Programming : GX works 3 Applied instructions, Arithmetic, Data transfer & Comparison Instructions Bit Grouping & Indexing Advance Programming : CJ, Call, Subroutine, Interrupt 09:30 am To 01:00 pm Analog Module Programming Built In Analog configuration & Function Analog Block/Adaptor interfacing & Programming 02:00 pm To 04:30 pm Introduction to Structure Programming Different Editor : Structure Ladder, FBD POU Types: Programming, Function & function Block Standard & User Library 13

14 Advance Modular PLC: MELSEC iq-r Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Three Days 09:30 am To 05:00pm 09:30 am To 01:00 pm Introduction to iq-r Series PLC Range of iq-r PLC & configuration Hardware & Features Difference Between Q Series & iq-r series PLC Compatibility with existing Product Line I/O addressing In iq-r PLC 02:00 pm To 05:00 pm PLC Programming : GX works 3 Creating New Projects Intuitive Program Drag & Drop Basic Programming Relay Instruction, Timer, Counter Built in Library Function 3 rd Party Partner Library 09:30 am To 01:00 pm PLC Programming : GX Works 3 Creating New Data Label & Setting Labels Creating FB & Programming Using FB Utilizing FB in Other Projects E-Manual Viewer 02:00 pm To 05:00 pm Analog Programming Range of Analog Modules / Intelligent Function Module Connections, Buffer Memory, Configuration Module Library Use of Module Labels for Analog/ Intelligent Module Programming Module Slot Change & Reflection In I/O Assignment Day 3 09:30 am To 01:00 pm Introduction to Embedded Data Base Recipe & Production Data Management Dedicated Commands like DB.INSERT, DB.SELECT Programming Examples 02:00 pm To 04:30 pm Maintenance & Security Function Data Logging & analysis Memory dump function Prevent System Downtime With Relay Security Key Protection Access Control By IP Address/Password Event Log History 14

15 Servo Basic - I Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electric Motor Participants must be well familiar with Mitsubishi PLC Two Days 09:30 am To 05:00pm 09:30 am To 01:00 pm Basics of Servo System Introduction to Servo Control System Servo Motor Basics & Structure Types of Encoder Absolute & Incremental System Mitsubishi Servo systems Pulse Type Servo Amplifier : MR-JE & MR-J4A Servo specifications & features Different types of Connectors & Cables for Servo Power Connections Guideline Signal Connections With Positioning Controllers : FX PLC Servo Display, Monitoring & Test Operations 02:00 pm To 05:00 pm Servo Programming : MR Configurator Servo Amplifier Parameter Setting Software Setup for Testing & Parameter Write/Backup In-Build Positioning Using Controller : FX PLC Fx PLC In-build high speed I/O Positioning Operation - Homing, - Positioning Incremental/Absolute - Speed Operation 09:30 am To 01:00 pm In-Build Positioning Using Controller : FX5 PLC Point Table Operation Positioning Using Modbus Protocol Servo wiring Modbus Protocol Modbus Registers Programming 02:00 pm To 04:30 pm Troubleshooting Alarms & Warning Servo Applications : Case Study discussion 15

16 Servo Basic - II Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of Mitsubishi Q PLC (Addressing & programming) Basics of Electric Motor & Encoder Participants must be gone through Servo Basic- I training Three Days 09:30 am To 05:00pm 09:30 am To 01:00 pm Overview of Mitsubishi Range of servo Controllers SSCNET Based Servo Controller : QD75M / MH / QD77MS Specifications & Parameters Servo Amplifier & Servo Motor Power, Signal Connections SSCNET Based Servo Amplifier : MR-J3 / MR J4 Specifications & Parameters SSCNET Connections with Positioning Controller ; QD77MS External signal Connections : Dog, Stop/Change, FLR & RLS I/O : Positioning Status & Command Details of Buffer Memory 02:00 pm To 05:00 pm QD77Ms/QD75MH Positioning parameters, Monitoring Data & Control Data Jog Operation Homing Operation : Different Types of Homing Error Monitoring & error Corrections Logic 09:30 am To 01:00 pm QD75MH / 77MS Point to Point Control using Buffer Memory Various Positioning Functions: INC/ABS, Interpolation, VF/VR etc. M-Code Current Value Change Functions Speed Override Function Teaching Function 02:00 pm To 05:00 pm Expansion Function of QD77MS Speed Position Torque Control Mode change Over function 16

17 Day 3 09:30 am To 01:00 pm QD77MS Simple Motion Configuration Synchronous parameters with single axis & linear cam Synchronous operation using sequence program CAM Design CAM types, resolution, stoke units Configuration of different types of CAM 02:00 pm To 04:30 pm Synchronous Parameters in Details Auxiliary Virtual Servo & encoder Axis Clutches, electronic Gears, Differential Gears & Speed change Gear. Programming using different components of Synchronous motion Troubleshooting & monitoring 17

18 Advance Servo: Q Motion Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of Q PLC (I/O Addressing, basic addressing) Fundamental of servo control (Positioning) Basics of electric motor & encoder Participants must be gone through Servo Basic-II Training Three Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm Overview of Mitsubishi Range of servo Controllers SSCNet based Servo system : MR-J4 Basics of servo systems Servo amplifier: MR-J4B/MR-J4WB Connections : SSCNET, External signals & power connections Parameters Q17nD/DS, Q170M/MS Motion CPU Range of motion CPU :Specifications & Configurations Motion Specific Modules : Q172DEX/ Q173DPX/Q172DLX OS Installation Special relays 7 register for Motion CPU 02:00 pm To 05:00 pm MT Developer - 2 New project creations Basic system setting Multiple CPU data sharing setting Fixed parameters 7 parameter blocks Servo Parameters 09:30 am To 01:00 pm SFC Programming SFC specifications SFC Programming Steps (F/FS/G etc.) Instruction For F/G Steps Servo Program (K) and various instructions 02:00 pm To 05:00 pm Exercise Homing using different methods: Near point dog Dog, Data Set etc. Single Axis positioning in real mode Interpolation ; Liner & Circular VF/VR Instructions 18

19 Day 3 09:30 am To 01:00 pm Motion Control : Virtual Mode Special bits 7 registers for virtual axis Servo programs allocation for virtual control Real to Virtual mode transaction Configuration of Virtual Axis Simultaneously operation of virtual & real axis Mechanical Editor, Input Methods : Servo Motors (Virtual Axis) / Synchronous encoder Connecting Modules : Different types of gears, Clutches, Different CAM types, resolution, stoke units 7 other programs Configuration of different types of CAM Selection of CAM for Output axis 02:00 pm To 04:30 pm Synchronous Parameters in Details Auxiliary Virtual Servo & encoder Axis Clutches, electronic Gears, Differential Gears & Speed change Gear. Output module: rotary Tables, Roller, Ball Screw & CAM. CAM Editor CAM Design : Feed CAM & reciprocating CAM 04:30 pm To 05:00 pm Feedback/ Interaction/ Self Evaluation 19

20 AC Drives Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of electric motor Participants must be well familiar with Mitsubishi Q PLC. Two Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm Mitsubishi Inverter : 800 Series Basics of inverter Mitsubishi range of Inverters - Inverter Selection - Selection of Peripheral devices (MCB, Magnetic Contactors, Thermal Relay etc.) Power & signal Connections V/F Control Operation Parameters Different types of load patterns Different modes of operations : PU, External & Net Mode Jog Operation 02:00 pm To 05:00 pm FR Configurator Parameter setting Multi- speed Operations Backup monitoring trend. Parameter copying with USB memory Auto Tuning 09:30 am To 01:00 pm Inverter control Using PLC Built-In PLC function in FR 800 series Inverter CC-Link/ CC-Link IE Communication 02:00 pm To 04:30 pm Troubleshooting Error & Warning codes Energy saving Using VFD Advance features of Mitsubishi VFD Application Study 20

21 SCADA: MC WorX64 Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of Electrical & Electronics Three Days 09:30 am To 05:00pm 09:30 am To 01:00 pm MC WorX 64 Introduction to MC WorX64 MC worx64: Architecture & Features Installation & System Requirement MC OPC Server OPC UA/Classic Interface Tag Creations Workbench Introduction to workbench Creating Project Configuration & layout Management Project Management Tool Workbench Run Time GraphWorX64 Basic Basic 2D Shapes & Objects 02:00 pm To 05:00 pm Graph WorX64 3d Space & Drawing Tools Dynamics in 3D Space Pipe Control Graph View Control Display Password Protection 09:30 am To 01:00 pm Workbench Tools Global Alias Local Alias Language Alias Alarm WorX64 & Viewer Alarm Tag Configuring Alarm Tags Group Alarms Tags by Area Alarm Logger Alarm Report 02:00 pm To 05:00 pm TrendWorX64 Trend Viewer TrendWorkX64 Logger UDM Registers & Expressions 21

22 Day 3 09:30 am To 01:00 pm Scripting Scripting Security Server Security Groups & Users Account Policies System Log In & Log Out 02:00 pm To 04:30 pm Project Management Review 22

23 Robot Training Pre-requisites Participants are expected to know the Co-ordinates, number systems (Binary, Hex, BCD). Basics of Electronics & Pneumatic Three Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm Robot Safety Industrial Robot Safety Basics of Robot Introduction to Mitsubishi Robot Series & Hardware Types of Mitsubishi Robot Controller & Manipulation Robot Basic Parameter Setting Device Configuration, Control Power Wiring of User Control (CNUSR) Wiring for External Inputs & Outputs Operation Panel & T/B Robot Operation Jog Operation, Hand Operation Joints, Cartesian, Too Jog Operation Robot Hand Opening & Closing 02:00 pm To 05:00 pm Programming Software : RT Toolbox 2 Robot Configuration using RT toolbox RT Toolbox Option Robot Programming MELFA Basic V Specification Constants, Variables, Common Variables Program Instructions Command Functions 09:30 am To 01:00 pm Robot Programming Using Teach Pendent Basic Operation of T/B Programming & Position teaching Program Editing Confirming Registered Position Data Operation Automatic Operation 02:00 pm To 05:00 pm Robot Programming Using RT Toolbox 2 Instruction Edit Scree/ Position Edit Screen Editing, teaching, Compensating etc. Program Editing Confirming Registered position Data Operation Automatic Operation Debugging Tool, External Tool & Work Offset Parameter Setting Liner & Continuous Path Programming Spline Interpolation Programming 23

24 Day 3 09:30 am To 01:00 pm Robot Application Programming Pick & Place Pallet Operation Machine Tending 02:00 pm To 04:30 pm Robot Parameter & Program Backup Robot Communication Option Robot Maintenance & Alarm 24

25 GOC (Graphic Operation Controller) Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of PLC, Basics of electronics Two Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm MEI PLC Product Range Overview Graphic Operation Controller (GOC) Features & Hardware Specification Hardware Main Unit, Expansion & COM Extension I/O Wiring GOC : Memory & Devices Application Memory & source Code I/O Addressing 02:00 pm To 05:00 pm PLC Programming : CoDeSys POU & Main PRG Explanation Basic relay, timer, Counter & Data Transfer Instructions Function Block & Library Analog Programming Analog Expansion Module & Specifications Programming Using Program-Configurator 09:30 am To 01:00 pm HMI Function : Visual Access Window (VAW) Scree Editing & Data Display, Data Entry Function Key i-key System Variables 02:00 pm To 04:30 pm Modbus RTU Configuration Mitsubishi MR-JE Servo Communication Using Modbus (Theoretical) Wiring Programming RTU Master & RTU Slave Point Table 25

26 Factory Automation Basics Training Pre-requisites Participants are expected to know the number systems (Binary, Hex, BCD). Basics of relay logic, digital electronics, & PLC. Two Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm Introduction to Electro-Pneumatics Pneumatic components - 5/2 way mono stable solenoid valve - 5/2 way bi-stable solenoid valve - 5/3 way solenoid valve, mid position closed. Electro Pneumatic components - Vertical feeder - Cylinder - Rotary manipulator - Conveyor belt - Conveyor sensor - Coins classifier - Containers sensors Introduction to control components Control buttons panel (Run, Stop, Reset, Auto/Manual, Single Cycle, Emergency) Power supply Solenoid valves manifold Stepper driver FX3S PLC I/O assignment Operation flowchart 02:00 pm To 05:00 pm Introduction to SFC programming Language Basics of SFC programming SFC blocks, transition etc. Single step mode operation Program loop instructions 09:30 am To 01:00 pm Introduction to Step ladder Basics of Step ladder Devices in STL State creation & transition in STL 02:00 pm To 04:30 pm Modes of Operation Step mode execution Single cycle execution Continuous cycle execution Alarm state 26

27 Packaging Machine HFS Training Pre-requisites Participants are expected to know Mitsubishi QD77MS & MRJ4 Servo Participants must be gone through Servo Basic-II Training Two Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm QD77MS & MR-J4 Servo Overview Specification Parameter I/O : Positioning status & Command Basics of Packing System Packaging machine types (Form Fill Seal Machine) Introduction to Horizontal Packing Machine Feeder axis Conveying Sealing Filing Sensor & Limit Switches Encoder Feedback 02:00 pm To 05:00 pm FA Hardware selection criteria System Configuration Wiring Configuration Application Development Packaging Machine HFS Parameter Setting for QD77MS & MR-J4 Servo Jogging Homing 09:30 am To 04:30 pm Application Development - Continue Feeder axis Conveying Sealing Filling Part/Object Missing correction logic Troubleshooting 27

28 Packaging Machine VFFS Training Pre-requisites Participants are expected to know Mitsubishi IQR PLC, RD77MS / QD77MS & MRJ4 Servo, and A800 AC drive Participants must be gone through Servo Basic-II Training Two Days 09:30 am To 05:00 pm 09:30 am To 01:00 pm iq-r PLC, RD77MS & MR-J4 Servo Overview Specification Parameter I/O: Positioning status & Command Basics of Packaging System Packaging machine types (Form Fill Seal Machine) Vertical FFS Packing Machine : Hardware overview Filling Systems (Auger Servo, Pulling Servo and Sealing Servo) Auto Print Mark Sensor assembly Web Unwind & Aligning assembly using A800 AC Drive Bag Draw down mechanism & Perforation / Batch assembly Sealing mechanism (Vertical & Horizontal) Heater & temperature control mechanism Energy Monitoring system 02:00 pm To 05:00 pm FA Hardware selection criteria System Configuration Wiring Configuration Application Development Parameter Setting for RD77MS4 & MR-J4 Servo Jogging & Homing of Pulling and Sealing Servos Unwinding of Web Pulling of Web and forming of pouch 09:30 am To 04:30 pm Application Development (Contd.) Unwinding of Web Pulling of Web and forming of pouch Sealing & Cutting operation & logic Temperature Control logic Auger filling operation & logic, Weight selection Eve mark correction logic Batch or Perforation logic and operation Troubleshooting 28

29 5. Customized Training Programmes Apart from regular training courses, we also conduct customized training on Mitsubishi s FA product as per customer s request at our training center or customer s site. Kindly contact concern training center for customized training courses, schedule & charges. 6. Training Charges and Instructions for Registration Regular training program are conducted as per training calendar schedule. Training charges for regular training courses at Mitsubishi FA centres are as follow Sr. No Training (Days) Charges (INR) 1 One Day 4, Two Days 8, Three Days 12, Four Days 16, Five Days 20, Service tax extra as applicable. These charges are applicable to all regular training courses on Mitsubishi FA product. Training venue can be selected from list of FA centres mentioned in brochure. The charges are applicable for all FA training centres. Accommodation & transportation will be arranged by participants. Fees once paid will not be refunded. Registration can be transferred to other participants from same company with prior intimation to training department. For registration, please send duly filled Training Request Form as given on following page to concern training center. Registration to be done with minimum Two Weeks in advance with full payment of training fees. 29

30 7. Training Request Form Mitsubishi Electric India Pvt.Ltd. Training Request Form To be filled by training requester / applicant FAC/TRG/123 Applicant Details : Name of Applicant Designation Department Organisation Contact Details Mobile : Details for requested course: Training Courses Training Type Regular as per MEI Training Calendar ( ) / Customised ( ) Expected Schedule Preferred Location Total No. of Participants Pune Center ( ) / Gurgaon Center ( ) / Bangalore Center ( ) / Chennai Center ( ) Ahmedabad Center ( ) or Customer Site (..) Specify the location if Customer site is selected Participants from the Same Organisation/Department Sr. No. Name of Participant Designation Department Mitsubishi FA Product Used : Payment details : I declare that the above mention information is correct & participants fulfil the pre-requisites for the mentioned courses. Place Date Signature of Applicant For Internal Used only at Mitsubishi Electric India Pvt. Ltd. Further communication / Action Planed Dates required : Quotation ( )/ PO Received ( ) / Date Confirmation ( )/ Site Visit require ( ) Allotted Engineer / Faculty for training Request: Kindly fill this form & send either hardcopy to nearby training center or to below address or scan copy. Contact Address : FAC, Mitsubishi Electric India Pvt. Ltd. EL-31/15, J Block, MIDC Bhosari, Pune (Maharashtra), India Tel : /127 Fax : MEI-FAID-FATraining@asia.meap.com 30

31 8. Mitsubishi Electric FA Center Guide Map Pune FA Center Mitsubishi Electric India Pvt. Ltd. Factory Automation & Industrial Division El31/15, J Block MIDC, Bhosari, Pune, Maharashtra. India Tel : /127 Near Point Land Mark Quality Circle Excellence Center, Sector 10, MIDC Bhosari. Pune Path Details Via Telco Road (1 Km) Head south-east towards Telco road Pass by Maratha Chamber Center on right Turn right at Mogora Cosmic Pvt. Ltd. On left. Turn right on Santosh Tea stall. Destination is on left side (second building after turn) From Pune Railway Station Follow for Kasarwadi Flyover - Landewadi Quality Circle, Telco Road Gurgaon FA Center Mitsubishi Electric India Pvt. Ltd. Factory Automation & Industrial Division 2 nd Floor, Tower A & B, DLF Cyber Greens, DLF Cyber City, DLF Phase III. Gurgaon, Haryana. India Tel : Near Point Land Mark IFFCO Chowk. Sector 29, Gurgaon Path Details Via NH8 Take NH8 to your destination. Taka a turn from Shankar Chowk. DLF cyber green building.(icici bank at ground floor) 31

32 Bangalore FA Center Mitsubishi Electric India Pvt. Ltd. Factory Automation & Industrial Division Prestige Emerald, 6 th Floor Municipal No 02, Madras Bank Road, (Lavelle Road) Bangalore, Karnataka India Tel : Near Point Land Mark M. Chinnaswamy Stadium, MG Road, Nagar Gandhi Park, Bangalore Path Details Via Queen Road & Lavelle Road (850 meter) Chennai FA Center Mitsubishi Electric India Pvt. Ltd. Factory Automation & Industrial Division No. 1 Vivekananda Road, Srinivasa Nagar, Off Spur Tank Road Chetpet, Chennai, TamilNadu. India Tel: Near Point Land Mark Egmore Railway Station, Egmore, Chennai Path Details Via Gandhi Irwin Road (2.3 Km) Follow Gandhi Irwin Road & Egmore High Road to E-Spur Tank Road Follow E-Spur Tank Road & spur Tank road to TV Road in M.S. Nagar Turn Right onto TV road. 32

33 Ahmedabad FA Center Mitsubishi Electric India Pvt. Ltd. Factory Automation & Industrial Division B/4, 3 rd Floor, Safal Profitaire Corporate Road. Prahalad Nagar, Satellite. Ahmedabad, Gujrat. India Tel : Near Point Land Mark Prahalad Nagar Garden Path Details From Prahalad Nagar Garden Walk east on 100 feet road/ Anand nagar road towards Corporate road. Turn right onto Corporate Rode 33