SOLADIN 2200 WEB / 3000 WEB GRID CONNECTED SOLAR INVERTER

Transcription

1 SOLADIN 2200 WEB / 3000 WEB GRID CONNECTED SOLAR INVERTER EN USER S AND INSTALLATION MANUAL P01 NL GEBRUIKERS- EN INSTALLATIEHANDLEIDING P29 DE BEDIENUNGS- UND INSTALLATIONSANLEITUNG P57 FR MANUEL UTILISATEURS ET D INSTALLATION P85 ES MANUAL DEL USUARIO Y DE INSTALACIÓN P113 IT MANUALE DI USO E MANUTENZIONE P141 compatible /05

2 2 EN / Soladin 2200 WEB / 3000 WEB User s Manual Figure 0-1: Overview 1. Power LED (Section 6.5) 2. Status LED (Section 6.5) 3. WIFI LED + WIFI connection button (Section 6.5) 4. PV negative input 5. PV positive input 6. Ground screw (Sections and 5.1) 7. AC output connector (Section 4.5) 8. WiFi module (Section 4.7) 9. Fixation screw 10. Identification label (Section 1.7)

3 EN / Soladin 2200 WEB / 3000 WEB User s Manual 3

4 4 EN / Soladin 2200 WEB / 3000 WEB User s Manual TABLE OF CONTENTS: 1 GENERAL INFORMATION Product description Use of this manual Validity of this manual Scope of warranty Liability Changes to the Soladin Identification label SAFETY GUIDELINES AND WARNINGS Warnings and symbols Use for intended purpose Installation, maintenance, repair Warning of special dangers HOW IT WORKS PV-modules Grid connected inverter Non-isolated inverter Grid interface Communication BEFORE YOU START Unpacking Things you need for installation General safety and installation precautions Installation environment AC connections Country suitability AC wiring AC plug RCD Grounding Reactive power Connection to a 230V 3_Phase Delta grid Load disconnection DC connections Specifications of the PV installation DC Switch Lightning protection Communication and interfacing Wi-Fi router Wi-Fi-module... 13

5 EN / Soladin 2200 WEB / 3000 WEB User s Manual 5 5 INSTALLATION Installation step-by-step Switching on Maintenance and de-commissioning COMMISSIONING AND SET-UP Country selection Soladin configuration page Visit IntelliWeb Wi-Fi mode LED table ADVANCED SETTINGS IntelliShade Accessing installer menu Installer menu: Country setting Installer menu: Power limiting TROUBLE SHOOTING TABLE TECHNICAL DATA Technical specifications Outline drawings CERTIFICATES EC Declaration of Conformity VDE V Certificate of compliance Konformitätsnachweis Eigenerzeugungseinheit Konformitätsnachweis NA-Schutz... 26

6 6 EN / Soladin 2200 WEB / 3000 WEB User s Manual 1 GENERAL INFORMATION 1.1 Product description The Soladin 2200 Web and 3000 Web, further referred to as Soladin or Soladin Web, are grid connected solar inverters. This inverter type is used to convert photovoltaic power and feed this into the grid. The Soladin Web is not suitable for stand-alone use (i.e. use without utility grid). 1.2 Use of this manual Copyright 2014 Mastervolt. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Mastervolt is prohibited. This manual serves as a guideline for the safe and effective use and installation of the Soladin: For the installer this manual gives directions for the installation, operation and commissioning. For the end user, this manual gives directions for the operation, maintenance and possible correction of minor malfunctions of this inverter. Every person who works with the apparatus should be familiar with the contents of this manual, and must carefully follow the instructions contained herein. Store the manual in an accessible place. 1.3 Validity of this manual This manual is valid for the following models: Part no Model Soladin 2200 Web Soladin 3000 Web All the specifications, provisions and instructions contained in this manual apply solely to the Mastervolt-delivered standard version of this inverter. 1.4 Scope of warranty Mastervolt assures a manufacturer s warranty of the Soladin Web during ten years after your purchase, on the condition that all instructions and warnings given in this manual are taken into account during installation and operation. Among other things, this means that installation is carried out by a qualified person, that installation and maintenance are executed according to the stated instructions and correct working sequence, and that no changes or repairs may have been performed on the Soladin other than by Mastervolt. The warranty is limited to the costs of repair and/or replacement of the product by Mastervolt only. For more details, refer to the Soladin Web warranty terms and conditions which are available on request. For making an appeal on warranty you can contact your supplier directly, stating your complaint, application, date of purchase and part number / serial number. 1.5 Liability Mastervolt accepts no liability for: consequential damage due to use of the Soladin Web; possible errors in the manuals and the results thereof. 1.6 Changes to the Soladin Changes to the Soladin Web inverter are not allowed. Changes to the Soladin Web software/ firmware, except for the settings made available to the user or installer, are not allowed. 1.7 Identification label Part no : Type : Soladin 2200 WEB Input : Vdc max, MPP Vdc, : 10A max, Uoc PV 500Vdc max, : Isc PV 13.9A max Output : 230Vac, 50/60Hz, 2.2kVA nom, 10.5A max, : Cos φ 0.85ind cap SSID : mastervolt-soladin-xxxx Reg key: xxxx Serial no: XXXXXXXXX Figure seconds The identification label is positioned at the right side of the Soladin. Refer to Figure 0-1, item 10 CAUTION! Never remove the identification label. VDE VDE AR-N 4105 G83/2 RD1699 IP65 CAT II 500V Design by Mastervolt, made in PRC

7 EN / Soladin 2200 WEB / 3000 WEB User s Manual 7 2 SAFETY GUIDELINES AND WARNINGS 2.1 Warnings and symbols Safety instructions and warnings are marked in this manual and on the product by the following pictograms: 15 sec IP65 A procedure, circumstance, etc which deserves extra attention. CAUTION! Special information, commands and prohibitions in order to prevent damage. WARNING A WARNING refers to possible injury to the user or installer or significant material damage to the Soladin if the installer / user does not (carefully) follow the stated procedures. Read this manual before installation and use This product has been declared conform the EC directives and standards. WARNING Lethal danger caused by high electric voltages present at the connectors after disconnecting DC and AC. AC connections: after 1 second the voltage at these connections has reached a safe level. DC connections: after 15 seconds the voltage at these connections has reached a safe level. This Indicates that no isolation transformer is present between the DC input and the AC output of the inverter Degree of protection: IP65. The product is protected against dust intrusion and water jets from any angle 2.2 Use for intended purpose The Soladin Web is constructed as per the applicable safety-technical guidelines. Use the Soladin Web inverter only in installations that meet the following qualifications: the electrical installation must meet the applicable regulations and standards (must be carried out correctly) and must be in a good condition; according to the technical specifications. WARNING Never use the Soladin Web in situations where there is danger of gas or dust explosion or potentially flammable products!. Use of the inverter other than as mentioned under section 2.2 is considered to be conflicting with the intended purpose. In such cases, Mastervolt will not accept liability for any damage or injury caused by the functioning or malfunctioning of the inverter 2.3 Installation, maintenance, repair WARNING As lethal voltages exist, only allow installation, maintenance and repair of the Soladin Web to be carried out by a qualified person. Connections and safety features must be executed according to the locally applicable regulations. In case of decommissioning and/or demounting follow the instructions as stated in this manual. If repairs or replacements are required, only use original Mastervolt spare parts. Make sure two persons are present when working on the installation, at least until the installation has been de-energized and verified by a suitable metering instrument. Safety class 1. This product must be provided with an equipment grounding conductor to the AC-output ground terminal

8 8 EN / Soladin 2200 WEB / 3000 WEB User s Manual 2.4 Warning of special dangers WARNING Two primary energy sources are present: solar panels (DC) utility grid (AC). Switch off both sources before starting any work on the installation. Block the switching device against unintentional reconnection. Verify the de-energizing of both DC and AC connections using a suitable metering instrument. The voltages present at the grid and solar side of the Soladin are not safe to touch. WARNING Do not try to open the inverter. There are no user serviceable parts inside.

9 EN / Soladin 2200 WEB / 3000 WEB User s Manual 9 3 HOW IT WORKS Solar input + _ Output 230V AC PV-panels Soladin Web Grid Wi-Fi communication Figure 3-1: Schematic example of the Soladin in a PV plant 3.1 PV-modules Photovoltaic (PV) modules convert light into DC power. A series of PV modules is called a string. The string must be connected to the solar input of the inverter. The PV string connected to the Soladin DC input is operated at its optimum voltage to obtain an optimal yield (Maximum Power Point tracking). A plane of PV modules is called a PV array and consists of multiple strings of the same length, being connected in parallel. 3.2 Grid connected inverter See figure 3-1. The Soladin Web is a grid connected photovoltaic power inverter. Its main task is to convert the high voltage DC power coming from the photovoltaic (PV) panels into AC power. The AC power is fed back into the public utility grid, 3.3 Non-isolated inverter The Soladin is a transformerless inverter. It is equipped with isolation resistance detection: it monitors PV array isolation resistance. 3.4 Grid interface The DC PV input is converted to an AC output: 230V AC. For the PV input operating voltage range refer to the specifications. The Soladin Web is not suitable to be operated in standalone mode (independently from the utility grid). The grid interface contains numerous safety mechanisms: Output relay to isolate the inverter from the grid. DC injection: Monitors DC current injection into the grid. Redundant grid voltage- and frequency monitoring Anti islanding protection: loss of utility detection Selection of country settings is mandatory for use of the Soladin. 3.5 Communication The Soladin Web configuration communicates through a Wi-Fi device, such as a notebook, smartphone or tablet. If you opt for online monitoring, the Soladin Web communicates via Wi-Fi through your internet router to the Internet as well.

10 10 EN / Soladin 2200 WEB / 3000 WEB User s Manual 4 BEFORE YOU START 4.1 Unpacking In addition to the Soladin the delivery includes: A mounting bracket to mount the Soladin to a wall This user s and installation manual AC plug 2 screws to fix the Soladin to the mounting bracket After unpacking, check the contents for possible damage. Do not use the product if it is damaged. If in doubt, contact your supplier. 4.2 Things you need for installation Make sure you have all further parts to install the Soladin: 4 screws max 4,5 mm (with plugs) to mount the Soladin to the wall, suitable to carry its weight. Wi-Fi access point (router) and associated password Wi-Fi device (smart phone, tablet or note book) Flat blade screwdriver 1x3.5 mm to connect the AC connector Philips screw drive 2x100 to fix the screws of the mounting bracket Double insulated AC cable to fit into the AC connector. 4.3 General safety and installation precautions WARNING Be sure that all wiring is disconnected from any power source during the entire installation. 4.4 Installation environment Obey the following stipulations when choosing a location to install the Soladin: Figure 4-1 The Soladin may be installed in indoor and outdoor environments. In case of outdoor installation, protect the top of the Soladin against accumulation of snow and ice (Figure 4-1). CAUTION! Short circuiting or reversing DC polarity may lead to damage to the Soladin, the cabling and/or the terminal connections. Follow all steps of the installation instructions in order of succession as described. WARNING When the PV array is exposed to light, it supplies a DC voltage to the solar inverter! Figure 4-2 Mount the Soladin vertically to a solid wall (Figure 4-2). Mount the Soladin on a maximum altitude of 2000 m.

11 EN / Soladin 2200 WEB / 3000 WEB User s Manual 11 NH 4 NaCl Figure 4-3 Do not expose the Soladin to direct sunlight or other heat sources (Figure 4-3). Do not expose the Soladin to excessive dust (Figure 4-3). Do not expose the Soladin to aggressive environments, ammonia or salt (Figure 4-3). Pollution degree: PD2 Ambient temperature: C; (power derating above 40 C). 20 cm 10 cm 10 cm 20 cm Figure cm When multiple Soladins are installed, side by side installation is recommended. Keep at least 20 cm horizontal clearance between Soladins. (Figure 4-5) This will avoid one inverter heating up the other. Figure 4-4 Keep at least 20cm vertical and 10 cm horizontal clearance between the Soladin and other objects (Figure 4-4) Allow sufficient ventilation to prevent build-up of hot air.

12 12 EN / Soladin 2200 WEB / 3000 WEB User s Manual Female insert with locking ring 2. Press screw, max torque 0.7 Nm 3. Back shell, max torque 0.7 Nm 4. Sealing gasket 5. Clamping ring 6. Cable nut, torque 1-2 Nm 6 Figure 4-6: AC plug 4.5 AC connections Country suitability European countries maintain different regulations with regard to the grid interface of solar inverters. Because of these different regulations the Soladin must be configured at first installation AC wiring The Soladin may only be used in a permanent installation, connected to a separate AC distribution group, to which no other electrical equipment is connected. The cabling between the junction box or electric cable duct and the Soladin must be double insulated. Use an appropriate AC-wire diameter, depending on the length of the wiring; see table below. Length Soladin model 2200 Web 3000 Web <10m 2.5 mm² 2.5 mm² 10-20m 2.5 mm² 4.0 mm² 20-30m 4.0 mm² 6.0 mm² Table 4-1: Recommended AC cable sizes AC plug The Soladin is delivered with an AC plug that fits into the AC connector. The plug is suitable for conductor diameters up to 3x6 mm². The AC wiring has to be led through the cable gland parts according to figure 4-6 and then connected according to figure 5-4 For France, in order to comply with local regulation UTE C we recommend to use a 10mm2 cable between the energy counter and the AC protection (AC breaker and/or RCD protection). The cable part between the AC protection and the AC plug of the inverter can be 4mm² or 6mm² depending on the line length RCD A RCD (Residual Current Device) according to VDE / EN is integrated into this inverter. It is not necessary to install an additional RCD in the system. In some countries and/or situations however, the use of an external RCD, according to IEC : (and national standards derived from this standard) is mandatory. In this case choose the rating of the RCD as such: RCD rating = number of inverters x 30mA Grounding The Soladin must be provided with an equipment grounding conductor to the AC-output ground terminal. Grounding and all other wiring must comply with local codes and ordinances. Functional electrical grounding of the positive or negative pole of the solar array is prohibited because the Soladin does not have a galvanic isolation between the DC-input and AC-output. When grounding of the solar array is necessary, an isolation transformer is required. See section 7.1 for specifications Reactive power As per January 1st 2012, PV installations in Germany capable of generating more than 3,68 kva will be required to provide reactive power. Reactive power is used by the utility operators to control the voltages in the power grid. As the share of power generated by PV installations grows every year, it becomes increasingly important for PV plants to support the grid similar to conventional power plants. The Soladin Web has been developed to meet the requirements according to the German VDE-AR-4105 standard. The specific features required in this norm will

13 EN / Soladin 2200 WEB / 3000 WEB User s Manual 13 automatically be enabled when the installation country Germany is selected: Active Power Derating; which is self-controlled by the inverter depending on the grid frequency, or set remotely by the grid operator. Reactive Power Provision; which is self-controlled by the inverter, depending on different variables (grid voltage or inverter output power) Active grid support functions limit the capacity of active power and therefore should be taken into account when designing a PV system. Mastervolt provides a SysCalc design tool to assist customers with system design work. It is available for free on Connection to a 230V 3_Phase Delta grid If the public grid is in a three phase 230V Delta configuration without neutral, the Soladin must be connected between two phases (230V) Load disconnection Install a separate circuit breaker for each Soladin to ensure that it can be disconnected safely when under load. 16A is the maximum permitted fuse protection DC Switch Use of an external DC-switch is required as described in IEC A suitable DC switch is available from Mastervolt under Part. Nr (Soladin DC switch 650V) Lightning protection The Soladin inverter is equipped with class III (micro) protection against surges inducted by lightning. Use of a complementary external class II overvoltage protection is advised if cable distance exceeds 15 meter. 4.7 Communication and interfacing Wi-Fi router Please bear in mind you need a Wi-Fi compatible router to be able to use IntelliWeb Wi-Fi-module The Soladin inverter features a demountable Wi-Fi-module. The Wi-Fi-module is also suitable for Italy test purposes. See figure DC connections Specifications of the PV installation CAUTION! Never connect voltages higher than specified to the inverter, as this will cause permanent damage to the inverter. The inverter will automatically limit the input current and power to its specified rating. Excess power will not be converted. Use of MultiContact MC4 connectors is mandatory! Figure 4-7: Wi-Fi-module The table below shows the recommended DC cable cross sections dependent on the cable lengths. Length Cross section <15m 2.5 mm² 15-25m 4 mm² 25-35m 6 mm² Table 4-2: Recommended DC cable sizes

14 14 EN / Soladin 2200 WEB / 3000 WEB User s Manual 5 INSTALLATION 5.1 Installation step-by-step WARNING Read chapters 2 and 4 prior to installation 4 Connect the AC wiring to the AC plug. The figure shows the cable inserts at the back side of the AC plug. 1 Mark the position of the mounting spots by using the mounting bracket. See figure 4-6. WARNING Check if L, N and PE are connected correctly L 1 2 N Insert the AC plug into the AC socket. PE Figure Fix the mounting bracket to the wall. Figure Make sure the DC-Switch is in the OFF (0) position. Then connect the string cabling to the Soladin Figure Place the Soladin over the mounting bracket and then move it downwards until it is locked by the mounting bracket. Figure Connect the grounding conductor coming from the PV array (if applicable) to the ground screw of the inverter. Refer to Figure 0-1, item 6. Figure Continue with section 5.2

15 EN / Soladin 2200 WEB / 3000 WEB User s Manual Switching on To check the correct operation of the Soladin, commissioning should be carried out during daytime only. Follow the steps described below to switch on the Soladin: 1 Check whether the DC-switch is still in the OFF position (or O -position). 2 Switch on the AC grid. 3 Move the DC-switch to the ON position (or I -position). 4 If sunlight is available, the Soladin will switch on but will not start inverting until the country has been selected 5 Continue with the set-up instructions as described in chapter Maintenance and de-commissioning No specific maintenance to the Soladin is required. Examine your electrical installation on a regular base, at least once a year. Defects such as loose connections, burnt wiring etc. must be corrected immediately. If necessary, use a soft clean cloth to clean enclosure of the Soladin. Never use any liquids, acids and/or scourers If it is necessary to de-commission the Soladin, follow the instructions in order of succession as described below: CAUTION! Follow below mentioned instructions in order of succession as described. 1 Cut off the grid voltage by switching off AC distribution switch in the meter cupboard. 2 Move the DC switch to the OFF-position. 3 Wait at least 15 seconds 4 Disconnect the MultiContact connectors from the Soladin using a Multicontact unlocking tool. 5 Disconnect the AC connector from the Soladin. 6 Disconnect communications cables, if any. Now the Soladin can be demounted in a safe way.

16 16 EN / Soladin 2200 WEB / 3000 WEB User s Manual 6 COMMISSIONING AND SET-UP 6.1 Country selection If the inverter is connected for the first time, the red (STATUS) LED will flash indicating that the country has not been set yet. To set the country of installation, a Wi-Fi connection shall be made between the Soladin and a Wi-Fi device such as a smartphone, tablet or notebook. 6.2 Soladin configuration page When connected, open the web browser on the Wi-Fi device and in the address bar, type [ ]. The Soladin internal web page will appear corresponding to Fig Select the preferred language in the lower left corner. Select the country of installation and press [Next]. (After initial commissioning, this feature is locked) Immediately after performing the country selection, the free IntelliWeb monitoring service can be set up (recommended). Before starting with steps 1 5, the installer may use a WiFi device, using the Wi-Fi network name and password of the (system-) owner, to check if the connection to the Internet is working properly. As the Soladin is powered through the PV panels only, settings should be performed during day time when sufficient energy from the PV panels is available. The Soladin generates a Wi-Fi network automatically during the first 30 minutes after power-up. The yellow (WIFI) LED flashes indicating that the inverter broadcasts a point-topoint Wi-Fi network. Figure 6-2: Soladin internal page country setting 3. Refer to Figure 6-3. The inverter can be set up to communicate with the free IntelliWeb monitoring service using the Wi-Fi network of the owner to connect to the Internet (option A). Alternatively, the set-up can be finished (option B) It is possible to either change the Wi-Fi network settings or set up an Internet connection and register the owner to IntelliWeb at a later stage, by re-starting the procedure at step 1. Preform the following steps for commissioning and set-up of the Soladin: 1. Check if the yellow WiFi LED (3) is slowly blinking ( ), indicating it is generating a point-to-point Wi-Fi network. If this is not the case, push the Wi-Fi button (3) shortly until the Wi-Fi LED blinks as indicated. Figure 6-3: Soladin internal web page Intelliweb connection set-up A B 2. Refer to fig Using a Wi-Fi device, connect to the WiFi network called [Mastervolt-Soladin-xxxx]. No password is required ( xxxx represents the last 4 digits of the Soladin serial number) Figure 6-1: Soladin Wi-Fi communication Point-to-Point mode

17 EN / Soladin 2200 WEB / 3000 WEB User s Manual Option A: Select the owner s Wi-Fi network from the list. Enter the corresponding password. Press [Save & Connect]. (Leave the box Get IP Address on Automatic ). Option B: Do not connect to the Internet now. Select this option when no Wi-Fi internet access is available. To complete set-up, select [Finish]. The Soladin will start converting power. The power indicator on the top of the Soladin will light up and fade out to indicate that power is being converted. 5. Refer to Fig Option A only - The Soladin will now: Break the Point-to-point connection with the WiFi device; Connect to the owner s Internet Router Register the Soladin to the IntelliWeb server automatically Redirect your Wi-Fi device to the Intelliweb web site automatically (or click [proceed by clicking here ]); 6.3 Visit IntelliWeb To monitor the energy production of the PV system, the owner can visit and log in to his personal account, using address and password. 6.4 Wi-Fi mode Refer to figure 0-1, position 3. Repeatedly (short) pressing the Wi-Fi mode button selects either one of the following Wi-Fi operation modes: Wi-Fi mode OFF Internet Mode Point-to-Point mode Figure 6-4: Soladin Wi-Fi communication Internet Mode Follow the instructions on the Internet page that comes up. You may now create an IntelliWeb account by registering the owner online or add the Soladin to an existing IntelliWeb account. An activation link will be sent to the owner s address.

18 18 EN / Soladin 2200 WEB / 3000 WEB User s Manual 6.5 LED table Refer to table 6-1 for WiFi LED indications LED Indication of the LED Meaning WiFi Mode All LEDs Off Insufficient irradiation Power LED Slow blinking < > < > < > <> <> < > <> <> <> Starting up Normal operation, low power Normal operation, high power Wi-Fi LED Status LED On Off On Off Connected with IntelliWeb Connecting to IntelliWeb Get IP address from Wi-Fi router Connecting to Wi-Fi router Inverter configuration Wi-Fi disabled Grid fault Hardware error Solar voltage too high Temperature too high No country selected Isolation fault Solar voltage low Normal operation Status + Power LED Fast blinking Software update in progress Do not switch off! Table 6-1: WiFi LED indications Internet Mode Internet Mode Internet Mode Internet Mode Point-to-point mode Off

19 EN / Soladin 2200 WEB / 3000 WEB User s Manual 19 7 ADVANCED SETTINGS 7.1 IntelliShade IntelliShade optimizes system performance when the solar array is partially shaded. The shadow MPP tracker function is standard disabled to prevent unnecessary losses in the Maximum Power Point Tracker. Connect your Wi-Fi device to the Soladin in point-to-point mode according to table 6-1. In the options menu IntelliShade can be enabled or disabled. 7.2 Accessing installer menu The Soladin Web inverter is equipped with a library of grid interface settings, enabling easy adaptation to country specific grid codes. Where required, the inverter may contribute to the static grid support. All country specific settings are automatically set when the country is selected during the commissioning. However, in certain cases, adjustment to the standard settings may be necessary Installer menu: Country setting During first commissioning, the country is selected. This automatically stores the correct grid interface parameters in the Soladin Web. The Country Settings menu allows to change the country of installation, if necessary. Choose the correct country and press Update. This will load the correct settings for the country and store them in the Soladin Web. Country setting Custom copies current settings to Custom and allows changing single settings, independent of the country installed. Changing the country during on-grid operation may lead to a disconnection and reconnection to the grid Installer menu: Power limiting Power limiting of the inverter may be required by regulations, for example, limitation to 70% of array capacity according to EEG2012 in Germany. In the options menu, check the box to enable the maximum power and set the maximum AC output power of the inverter. The following parameters can be adjusted when authorized as installer: Country selection Voltage- and frequency limits, Insulation detection and anti-islanding protection Maximum inverter power (Power limiting to 70% of array capacity according to the German EEG2012) An installer password can be obtained from Mastervolt Technical Support. Connect your Wi-Fi device to the Soladin in point-to-point mode according to table 6-1. Click on Advanced settings in the bottom left part of the screen and enter your personal Installer password. If the password is correct, the Country settings menu will be displayed.

20 20 EN / Soladin 2200 WEB / 3000 WEB User s Manual 8 TROUBLE SHOOTING TABLE LED Indication of the LED Meaning What to do? Status LED On continuous Grid fault Check AC fuse, circuit breaker, cabling Status LED Hardware error Contact your Mastervolt supplier blinking 6 times Status LED Solar voltage too high Check the PV string length blinking 5 times Status LED Temperature too high Check the fan and free ventilation blinking 4 times Status LED No country selected Select the country in the configuration page blinking 3 times Status LED PV insulation ground fault Check the PV-installation for insulation errors blinking 2 times Status LED Solar voltage low During dusk and dawn this can occur. blinking 1 time Wi-Fi LED blinking 4 times Wi-Fi LED Wi-Fi LED Wi-Fi LED blinking 3 times blinking 2 times blinking 1 time The Wi-Fi connection with the router is established but there is no internet connection. Because of a new router or otherwise you want to change the Wi-Fi settings. You cannot find the internet router home network in the list. There is no Wi-Fi connection between the Soladin and Wi-Fi-device The Soladin is connected to your home network, but is not able to connect to our servers. The Soladin cannot obtain an IP address which it needs to access your local network The Soladin cannot connect to the Wi-Fi network Setup modus Your internet server or the internet cable connection may be down. The router may be installed too far from the Soladin or it is defect. Check your home internet connection Try unplugging and replugging your router. Check if you can reach If you can reach other Internet sites, but not IntelliWeb, our service might be temporarily disrupted. Is the Wi-Fi password correct? Use the Soladin setup to verify and, if needed, correct the password. Check if your router is configured as a DHCP server, verify and correct your router settings if necessary. There may be a problem within the router, replug your router s power cord Is the home router plugged in and switched on? Check the cables and plug them in if needed. Is the Wi-Fi password correct? Use the Soladin setup to verify and, if needed, correct the password. Is the signal strength ok? Go to the location where your Soladin is installed and check if you can connect to your home network with a smartphone, tablet or laptop. May be caused by Wi-Fi-interference; press WIFI connection button (Fig 0-1, ref.3) three times shortly to disable and enable the Internet Mode. Then the SSID will broadcast on a different Wi-Fi-channel This is a normal situation. The Wi-Fi LED stays blinking during 30 minutes or shorter if the setup was finished earlier. Check your server and internet cable. Refer to section 6.1 for instructions. Check the position of your router and if it is working correctly. Check if your Wi-Fi-device is working correctly and check its password.

21 EN / Soladin 2200 WEB / 3000 WEB User s Manual 21 9 TECHNICAL DATA 9.1 Technical specifications Soladin 2200 Web Soladin 3000 Web GENERAL Part number: Operating temperature: Ambient temperature -20 C to 60 C (Full power up to 40 C ambient) Enclosure: Powder coated aluminum Protection degree: IP65 Climate class: 4K4H Pollution degree: PD2 Maximum altitude: 2000m Relative humidity: <95% condensing Safety class: Class I Inverter technology: Transformerless Cooling: Natural convection Weight: 18kg 18kg Dimensions, hxwxd: Refer to section 9.2 Refer to section 9.2 SOLAR INPUT (DC) PV power range: Wp Wp Start-up power: 8.5 W 8.5 W Operating voltage: V V MPPT voltage range: V V Nominal voltage: 350 V 400 V Absolute maximum voltage: 500 V 630 V Overvoltage category: OVC2 OVC2 Number of inputs: 1 MPP Tracker / 1 set of DC connectors Maximum input current: 10 A 10 A Maximum short circuit current: I sc = 12 A I sc = 12 A Max. inverter backfeed to PV-array Backfeed current to the PV-array is negligible DC protection: Surge arresters class III according to IEC GRID OUTPUT (AC) Voltage: 230 Vac single phase +15% / -20%, country dependent Overvoltage category: OVC3 OVC3 Nominal Power: 2200VA 3000VA Maximum power: 2200VA 3000VA Maximum current: 10.5 A 14.3 A Frequency: 50 / 60 ± 3Hz 50 / 60 ± 3Hz Nominal Power factor: > 0.99 > 0.99 Reactive power control: Yes Yes Power factor 0.85 Leading 0.85 Lagging 0.85 Leading 0.85 Lagging Standby Power consumption: < 1 W < 1 W EU efficiency: 96.2 % 96.2 % Maximum efficiency: 97.1 % 97.1 % AC connector: mm² mm² Max. inverter backfeed to grid 0A 0A Inrush current 30A peak, 1ms 30A peak, 1ms Fault current 16A max 16A max Overcurrent protection 30A max 30A max

22 22 EN / Soladin 2200 WEB / 3000 WEB User s Manual REGULATIONS AND DIRECTIVES CE conformity: Approved for use in: Soladin 2200 Web Yes Soladin 3000 Web UK, DE, FR, IT, ES, NL, BE, GR, AT, DK, EI, BG, CZ, FR-Dom/Tom National grid requirements: VDE ; VDE-AR-N4105; CEI-021; RD1699; G83/2; C10/11 COMMUNICATION & MONITORING Indicators: Monitoring: Communication: Status LED, Power LED and Wi-Fi LED Monitoring portal (access included) Wi-Fi (B/G/N) TECHNICAL REQUIREMENTS ISOLATION TRANSFORMER (if required, see section 4.5.5) Voltage (primary / secondary) 230V L+N / 230V L+N 230V L+N / 230V L+N Frequency: 50 / 60Hz 50 / 60Hz Power: 2200VA 3000VA Type: Safety transformer, Isolation class F Normatives & regulations: IEC , locally applicable regulations and standards apply. 9.2 Outline drawings [18.25] [18.09] [6.32] Figure 9-1: Dimensions of the Soladin 2200 Web and 3000 Web

23 EN / Soladin 2200 WEB / 3000 WEB User s Manual CERTIFICATES 10.1 EC Declaration of Conformity We, Manufacturer Mastervolt International B.V. Address Snijdersbergweg AN Amsterdam The Netherlands Declare under our sole responsibility that the product: Article number Product name Soladin 2200 Web Soladin 3000 Web is in conformity with the provisions of the applicable directives: 2004/108/EC EN : A1: A2:2009 EN :2008 EN :2007 EN : A1: /95/EC EN : A11: A1:2010 EN :2010 EN :2011 1) 2) 1999/5/EC EN V1.8.1 EN V ) 2) EN V ) 2) EN 62311: /65/EU NOTES: 1) Notified body involved: ) Wireless module only 1) 2) 1) 2) Amsterdam, 16 May-2014 MASTERVOLT INTERNATIONAL B.V. Ing. D.R. Bassie Product Manager Solar

24 24 EN / Soladin 2200 WEB / 3000 WEB User s Manual 10.2 VDE V Certificate of compliance

25 10.3 Konformitätsnachweis Eigenerzeugungseinheit EN / Soladin 2200 WEB / 3000 WEB User s Manual 25

26 26 EN / Soladin 2200 WEB / 3000 WEB User s Manual 10.4 Konformitätsnachweis NA-Schutz

27 NOTES EN / Soladin 2200 WEB / 3000 WEB User s Manual 27

28 28 EN / Soladin 2200 WEB / 3000 WEB User s Manual MASTERVOLT, Snijdersbergweg 93, 1105 AN Amsterdam, The Netherlands, T: +31 (0) , F: +31 (0) , www mastervolt.com