THERMAL PRINTER. TSP700 Series TECHNICAL MANUAL [ FIRST EDITION ]
|
|
|
- Doreen Webb
- 5 years ago
- Views:
Transcription
1 THERMAL PRINTER TSP700 Series TECHNICAL MANUAL [ FIRST EDITION ]
2 NOTICE All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR s express permission is forbidden. The contents of this manual are subject to change without notice. All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press. However, should any errors be detected, STAR would greatly appreciate being informed of them. The above notwithstanding, STAR can assume no responsibility for any errors in this manual. Copyright 2001Star Micronics Co.,Ltd.
3 INTRODUCTION This manual describes the thermal printer TSP700 series. It is designed for use as a reference for periodic inspections and maintenance procedures to be executed by service personnel. It is not intended for the general user. Users of this manual should have a basic knowledge and understanding of the English language. 1 2 This manual is divided into the following sections: Chapter 1 Parts Replacement and Adjustments Chapter 2 Maintenance and Lubrication Chapter 3 Parts List 3 First edition : Mar. 2001
4
5 CHAPTER 1 PARTS REPLACEMENT This chapter explains disassembly and reassembly of the printer. Note the following precautions during disassembly and reassembly. 1. Disconnect the printer power cord plug from the wall outlet before servicing it. 2. Assembly is the reverse of disassembly unless otherwise specified. 3. After reassembly, coat the screw heads with locking sealant. 4. Lubrication information is not provided in this chapter. Refer to item 2 of chapter The printer has no adjustable parts Lower Case Unit Upper Case Unit Board Chassis Unit Main Logic Board Platen Unit Paper Feed Motor...5
6
7 PARTS REPLACEMENT 1. Lower Case Unit (1) Turn off the power switch 1, disconnect the power cord from the wall outlet. (2) Remove Two tapping screws 2 Two tapping screws 3 Lower case unit Upper Case Unit (1) Turn off the power switch1, disconnect the power cord from the wall outlet. (2) Remove the lower case unit according to the procedure described in item 1. (3) Push the cover open lever 2, and open the printer cover 3. (4) Remove the upper case unit
8 PARTS REPLACEMENT 3. Board Chassis Unit (1) Turn off the power switch1, disconnect the power cord from the wall outlet (2) Remove Upper case according to the procedure described in item 2. Three screws 2 Screw 3 Screw 4 Three wires 5 Six connectors 6 Printer mechanism 7 Board chassis unit A Main Logic Board (1) Turn off the power switch, disconnect the power coard from the wall outlet A A B B (2) Remove Board chassis unit according to the procedure described in item 3. Two screws 1 Interface board unit 2 Six screws 3 Two connectors 4 Power switch 5 Sub-board 6 Main logic board 7 Board chassis 8 8 4
9 PARTS REPLACEMENT Platen Unit (1) Turn off the power switch, disconnect the power cord from the wall outlet. (2) Push the cover open lever 1, and open the printer cover 2. 2 (3) Remove Stop ring 3 Bearing 4 Platen unit Paper Feed Motor (1) Turn off the power switch, disconnect the power cord from the wall outlet. (2) Remove Printer mechanism according to the procedure described in item 3. Screw 1 Paper feed motor unit
10
11 CHAPTER 2 MAINTENANCE AND LUBRICATION 1 1. Maintenance Cleaning Checks Lubrication Type of oil Lubrication method Lubrication locations... 10
12
13 MAINTENANCE AND LUBRICATION 1. Maintenance Carry out maintenance control items listed below to maintain the original performance of this printer and prevent trouble from occurring Cleaning (1) Removal of dirt. Clean the dirt with tissure or soft cloth. Note: Do not use thinners or trichlene/ketone base solvents for cleaning as they can damage plastic parts. Be careful not to damage electrical parts, wired areas or mechanisms and avoid getting them wet. (2) Removal of dust, pile, etc. Clean with a vacuum cleaner. Note: Check the amount of oil after cleaning and lubricate if necessary Checks Maintenance checks for this printer is divided into the two areas of daily check that the person using the printer carries out during normal use and regular check that can be done only by an experienced person with a knowledge of the equipment. (1) Daily check: Check that the printer is being properly used. Is the peper set correctly? Is there any dirt or foreign object in the printer? (2) Regular check: Carry out regular check and lubrication after six months use or after printing 1 million lines. Check for bending of springs. Remove any dirt or dust in the area of the detectors. 9
14 MAINTENANCE AND LUBRICATION 2. Lubrication Lubrication is extremely important for preserving the original performance of the printer over a long period of time Type of oil The type of oil used has a major influence on the performance and durability of the printer.you should pay particular attention to the cold temperature properties of the oil. We recommend use of the grease and lubrication oils listed below for this printer. Type of oil Product name Manufacturer Grease Molykote EM-30L Dow Corning Corp Lubrication method When lubricating during disassembly or assembly operations, be sure to wash and clean the equipment well prior to lubrication to remove dirt and dust. Lubricate the equipment at regular intervals of six months or after every one million lines. Be sure to lubricate equipment after disassembling or replacing parts when oil has been removed by cleaning Lubrication locations Lubrication locations Type of oil 1 Rubbing surface of Shaft C and Frame Molykote EM-30L 2 Rubbing surface of Case stopper and Screw and Frame Molykote EM-30L 3 Rubbing surface of Gear and Frame shaft Molykote EM-30L 4 Rubbing surface of Gear and Freme shaft Molykote EM-30L 5 Rubbing surface of Cover B assy and Lock lever Molykote EM-30L 6 Rubbing surface of Lock lever and Cover open lever Molykote EM-30L 7 Rubbing surface of Release plate and Cover B assy Molykote EM-30L 8 Rubbing surface of Release plate and Lock plate Molykote EM-30L 9 Rubbing surface of Lock plate and Cover B assy Molykote EM-30L 0 Rubbing surface of Lock plate and Lock plate spring Molykote EM-30L A Rubbing surface of detector holder and near-end detector cover Molykote EM-30L 10
15 MAINTENANCE AND LUBRICATION F G E D F G A B 5 6 A 1 C1 1 C2 C D E A B C3 Fig. 2-1 Lubricated Area 11
16
17 CHAPTER 3 PARTS LIST HOW TO USE PARTS LIST (1) DRWG. NO. This column shows the drawing number of the illustration. (2) REVISED EDITION MARK This column shows a revision number. (3) PART NO. Parts numbers must be notified when ordering replacement parts. Parts described as NPN have no parts number and are not in stock, i.e., unavailable. (4) PARTS NAME Parts names must be notified when ordering replacement parts. (5) Q TY This column shows the number of the part used as indicated in the figure. (6) REMARKS When differences in specifications exist depending on location/destination. (7) RANK Parts marked S a service parts. Service parts are recommended to be in stock for maintenance Printer Assembly Disassembly Drawing Parts List Printer Mechanism Disassembly Drawing Parts List Sub-Assembly Cover Open Lever Unit Head Unit Block Diagram Main Logic Board Circuit Diagram Parts List Sub-Board Circuit Diagram Parts List Serial Interface Board (25pin) Circuit Diagram Parts List Serial Interface Board (9pin) Circuit Diagram Parts List USB Interface Board Circuit Diagram Parts List Parallel Interface Board Circuit Diagram Parts List... 38
18 3-1. Printer Assembly Disassembly Drawing 7 C C E F 11 F E D 11 B A B A 4 11 D
19 Parts List Printer Assembly DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK LOWER CASE UNIT TSP7 1 2 NPN BOARD CHASSIS TSP THERMAL ROLL PAPER 80X35D MAIN LOGIC BOARD UNIT TSP SUB-BOARD UNIT TSP TMP S UPPER CASE UNIT TSP INTERFACE BOARD IFBD-HD03 1 OPTION:SERIAL 25 PIN INTERFACE BOARD IFBD-HN03 1 OPTION:SERIAL 9 PIN INTERFACE BOARD IFBD-HU03 1 OPTION:SERIAL USB INTERFACE BOARD IFBD-HC03 1 OPTION:PARALLEL IF ADAPTER SET PS60-24A JP 1 OPTION ADAPTER SET PS60-24A US 1 OPTION ADAPTER SET PS60-24A EU 1 OPTION ADAPTER SET PS60-24A UK 1 OPTION ADAPTER SET PS60-24A AS 1 OPTION 10 NPN SWITCH COVER TSP SCREW TAT 3-6 CT-FL SCREW TAT 3-6 CT SCREW TAT 3-12 PT-FL SCREW TAT 3-8 PT-FL SCREW TR NPN FERRITE CORE K5BRC24X14X11 1 PARALLEL IF FASTENER T18S 1 PARALLEL IF 15
20 Printer Mechanism Disassembly Drawing A D C E C1 C2 A F F E D G G B B C3
21 Parts List DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK 1 NPN WIRE 26UL1007BLK060TT BEARING TMP8 1 S 3 NPN COVER A TMP CUTTER UNIT ORC-RSY90 1 S 5 NPN PAPER GUIDE B TMP7 1 6 NPN PAPER GUIDE A TMP7 1 7 NPN PE DETECTOR COVER UNIT TMP8 1 8 NPN PE DETECTOR UNIT TMP PLATEN UNIT TMP7 1 S 10 NPN RELEASE PLATE TMP GEAR 24X0.7-55X0.5 TMP GEAR 40X0.5 TMP NPN SHAFT B TMP NPN LOCK LEVER TMP NPN HEAD HOLDER PLATE UNIT TMP NPN OIL DAMPER 058E-F 1 17 NPN SHAFT C TMP NPN TENSION SHAFT HOLDER TMP NPN CASE STOPPER TMP NPN GROUND PLATE A TMP NPN CUTTER PLATE TMP NPN FRAME UNIT TMP NPN TENSION SHAFT TMP NPN PUSH LEVER TMP PF MOTOR UNIT TMP8 1 S 26 NPN NEAR-END DETECTOR COVER TMP NEAR-END DETECTOR ASSY TMP NPN COVER OPEN LEVER UNIT TMP HEAD UNIT TMP NPN COVER B ASSY TMP NPN LOCK PLATE TMP NPN LOCK PLATE SPRING TMP NPN GEAR 14X40X0.8 TMP NPN SHAFT LEVER TMP NPN DETECTOR LEVER TMP NPN HEAD LEVER R TMP NPN HEAD LEVER L TMP ROLL PAPER GUIDE TMP NPN DETECTOR HOLDER TMP NPN LOCK PLATE SPRING TMP SCREW TAT 2-10 PT SCREW TR SCREW TAT SCREW TAT 2-6 PT SCREW TAT 3-5 CT-FL SCREW TR SCREW TAT 3-6 CT SCREW TAT 3-6 PT SCREW TAT 3-6 PT-FL SCREW TAT 3-8 PT STOP RING SE STOP RING SE NPN CLAMP SPRING TMP FASTENER T18S 3 56 NPN FERRITE CORE BP COLLAR Printer Mechanism
22 Printer Mechanism DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK 58 NPN SPRING E NPN SPRING E NPN SPRING C NPN SPRING C NPN SPRING C NPN CAUTION SEAL TMP NPN PAPER SET SEAL TMP NPN WIRE 18UL1007BLK245TT STATIONARY KNIFE ORC-RSY90 1 S CUT WASHER 4.1X6.5X CUT WASHER 5.2X8.0X
23 3-3. Sub-Assembly Cover Open Lever Unit DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK 28-1 NPN SCREW TAT NPN STOP RING SE NPN SPRING E NPN SHAFT A TMP NPN LEVER PLATE TMP NPN COVER OPEN LEVER TMP8 1 19
24 Head Unit DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK SCREW TAT CT SCREW TR 3-4 FL NPN HEAD EARTH PLATE TMP NPN WIRE 18UL1007BRN145TT THERMAL HEAD AE080-H8E801 1 S COLLAR TMP NPN HEAD PLATE TMP CABLE UNIT 15X175CC TMP NPN FERRITE CORE K5BRC16X16X8-M 1 20
25 3-4. Block Diagram 21
26 3-5. Main Logic Board Circuit Diagram Main Logic Board (1/5) 22
27 23 Main Logic Board (2/5)
28 24 Main Logic Board (3/5)
29 25 Main Logic Board (4/5)
30 26 Main Logic Board (5/5)
31 Parts List DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK C01 NPN CERA.CAPA.CHIP UF 10V 1 C02 C03-06 NPN CERA.CAPA.CHIP UF 50V 4 C07-09 C11-19 C21-22 C31-32 C33 NPN CHEM. CAPA. 47UF 35V 1 C34-35 C36 NPN CERA.CAPA.CHIP PF 50V 1 C41 C42-43 NPN CERA.CAPA.CHIP UF 25V 2 C44 C45 NPN CERA.CAPA.CHIP UF 50V 1 C51 NPN FILM CAPA. 0.1UF 50V 1 C52 NPN CERA.CAPA.CHIP UF 50V 1 C53-54 C55 NPN CHEM. CAPA. 470UF 10V 1 C56 NPN CHEM. CAPA. 1000UF 35V 1 C61 NPN CERA.CAPA.CHIP UF 25V 1 BC01-03 NPN CERA.CAPA.CHIP UF 50V 3 BC04-07 NPN CERA.CAPA.CHIP UF 25V 4 BC08A NPN CERA.CAPA.CHIP UF 50V 1 BC08B NPN CHEM. CAPA. 47UF 35V 1 BC09 NPN CHEM. CAPA. 47UF 35V 1 BC10 NPN CERA.CAPA.CHIP UF 50V 1 BC12 CN01 NPN CONNECTOR B14B-PH-K-S 1 CN02 NPN CONNECTOR B15B-PH-K-S 1 CN03 NPN CONNECTOR CN04 NPN CONNECTOR PHEC40R-R111 1 CN05 NPN CONNECTOR A 1 CN06 NPN CONNECTOR CN08 NPN CONNECTOR CN09 NPN CONNECTOR CN10 CN11 NPN CONNECTOR D1-4 NPN SCHOTTKY DIODE CHIP D1FS4* 4 D5-6 NPN DIODE CHIP D1F * 2 DSW1 NPN DIP SWITCH 210B008MS 1 DSW2 NPN DIP SWITCH 210B004MS 1 FB01-05 NPN CHIP BEADS IND. BK1608HS601* 5 FB06-07 FB08 NPN CHIP BEADS IND. BK1608HS601* 1 FB09-10 NPN CHIP BEADS IND. BK2125HS470* 2 IC01 NPN IC-RESET M51953BFP*E2 1 IC02 NPN CPU HD F20 1 IC03 NPN GATE ARRAY LZ9FG28-TSPA 1 IC04 NPN FLASH MEMORY 28F400BVE-85 1 T7 ** IC05 NPN FLASH MEMORY 28F400BVE-85 1 T7#SD *.* IC06-07 NPN SRAM AGZ-70LL* 2 IC08 NPN IC-MOTOR MTD2003F IC09 NPN IC-MOTOR TA8428K 1 IC10 NPN IC-LIN UPC393G2*T1 1 IC11 NPN IC-REG SI-8401L 1 IC12 27 Main Logic Board
32 Main Logic Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK JP1A NPN CHIP RESISTOR 0 OHM 1/16W 1 JP1B JP2 LED1-2 NPN LED CHIP LT1E40A* 2 LED3 NPN LED CHIP LT1D40A* 1 R101 NPN CHIP RESISTOR 1.5 KOHM 1/16W 1 R102 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R103 NPN CHIP RESISTOR 2.2 K-OHM 1/16W 1 R104 NPN CHIP RESISTOR 22 K-OHM 1/16W 1 R105 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R106 NPN CHIP RESISTOR 470 OHM 1/16W 1 R107 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R108 NPN CHIP RESISTOR 470 OHM 1/16W 1 R109 NPN CHIP RESISTOR 100 OHM 1/16W 1 R NPN CHIP RESISTOR 10 K-OHM 1/16W 4 R R NPN CHIP RESISTOR 10 K-OHM 1/16W 3 R125 R NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R NPN CHIP RESISTOR 330 OHM 1/16W 3 R R135 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R NPN CHIP RESISTOR 10 K-OHM 1/16W 3 R139 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R NPN CHIP RESISTOR 330 OHM 1/16W 4 R146 NPN CHIP RESISTOR 220 OHM 1/16W 1 R147 R NPN CHIP RESISTOR 330 OHM 1/16W 6 R NPN CHIP RESISTOR 10 K-OHM 1/16W 5 R NPN CHIP RESISTOR 100 K-OHM 1/16W 3 R NPN CHIP RESISTOR 100 K-OHM 1/16W 2 R165 NPN CHIP RESISTOR 470 OHM 1/10W 1 R NPN CHIP RESISTOR 100 K-OHM 1/16W 5 R R177 NPN CHIP RESISTOR 0 OHM 1/16W 1 R178 NPN CHIP RESISTOR 100 OHM 1/16W 1 R179 NPN CHIP RESISTOR 0 OHM 1/16W 1 R180 NPN CHIP RESISTOR 100 OHM 1/16W 1 R R NPN CHIP RESISTOR 10 K-OHM 1/16W 3 R NPN CHIP RESISTOR 1 K-OHM 1/16W 3 R207 NPN CHIP RESISTOR 330 OHM 1/16W 1 R208 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R209 NPN CHIP RESISTOR 15 K-OHM 1/16W 1 R210 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R NPN CHIP RESISTOR 10 K-OHM 1/10W 2 R NPN CHIP RESISTOR 10 K-OHM 1/16W 4 R217 NPN CHIP RESISTOR 330 OHM 1/16W 1 R NPN CHIP RESISTOR 1 K-OHM 1/16W 3 R NPN CHIP RESISTOR 330 OHM 1/16W 2 R NPN CHIP RESISTOR 10 K-OHM 1/16W 4 R NPN CHIP RESISTOR 100 OHM 1/16W 4 R NPN CHIP RESISTOR 10 K-OHM 1/16W 4 R235 NPN CHIP RESISTOR 15 K-OHM 1/16W 1 R NPN CHIP RESISTOR 1.0 OHM 1W 2 28
33 Main Logic Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK R NPN CHIP RESISTOR 100 K-OHM 1/16W 5 R306 R NPN CHIP RESISTOR 100 K-OHM 1/16W 2 R310 R NPN CHIP RESISTOR 330 OHM 1/16W 2 R NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R315 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R316 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R317 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R320 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R321 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R322 R323 NPN CHIP RESISTOR 330 OHM 1/10W 1 R324 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R NPN CHIP RESISTOR 4.7 K-OHM 1/16W 2 R329 R330 NPN CHIP RESISTOR 330 OHM 1/10W 1 R NPN CHIP RESISTOR 1 K-OHM 1/16W 2 R NPN CHIP RESISTOR 330 OHM 1/16W 2 R405 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R406 NPN CHIP RESISTOR 33 K-OHM 1/16W 1 R407 NPN CHIP RESISTOR 10 K-OHM 1/10W 1 R R NPN CHIP RESISTOR 4.7 K-OHM 1/16W 3 R NPN CHIP RESISTOR 10 K-OHM 1/16W 3 R NPN CHIP RESISTOR 470 OHM 1/10W 2 R NPN CHIP RESISTOR 330 OHM 1/16W 3 R454 NPN CHIP RESISTOR 15 K-OHM 1/16W 1 R455 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R456 NPN CHIP RESISTOR 2.2 K-OHM 1/16W 1 RA01-04 NPN RESIS. ARRAY CHIP MNR14J221* 4 RA05-09 NPN RESIS. ARRAY CHIP MNR14J331* 5 REG1 NPN IC-REG UPC SW1 NPN PUSH SWITCH SKHHAL 1 TR01 NPN CHIP TRANSISTOR 2SA1362GR*85R 1 TR02 NPN CHIP TRANSISTOR 2SC3875S-G*AL 1 TR03 NPN CHIP TRANSISTOR 2SA1649Z* 1 TR04 NPN CHIP TRANSISTOR 2SA *TA 1 TR05-07 NPN DIGITAL TRANSISTOR FA1A4P 3 TR TRANSISTOR 2SD TR10 NPN CHIP TRANSISTOR 2SC3875S-G*AL 1 TR11 NPN CHIP TRANSISTOR 2SA1362GR*85R 1 TR12 NPN DIGITAL TRANSISTOR FA1A4P 1 VR1-2 NPN RP RESISTOR RH0615C-47K 2 XTAL NPN CERA. OSCILLATOR EFOMC2005T4* 1 ZD1 NPN ZENER DIODE CHIP HZU20B2TRF 1 ZD2 NPN ZENER DIODE RD7.5EB1T 1 29
34 3-6. Sub-Board Circuit Diagram Parts List Sub-Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK C1-2 CN21 NPN CONNECTOR TCS CN22 NPN CONNECTOR CN23 NPN CABLE UNIT 2X60CC TSP8 1 CN24 NPN CABLE UNIT 4X60CC TSP8 1 CN25 NPN CABLE UNIT 2X125C TSP8 1 F FUSE MRT3.15A-250V* 1 L1-2 NPN JUMPER WIRE 1/6W-L NPN SEESAW SWITCH SF-W1H1A14BB 1 NPN HEAT-SHRINK TUBE F
35 3-7. Serial Interface Board (25 pin) Circuit Diagram 31
36 Parts List Serial Interface Board (25 pin) DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK C1 NPN CHEM. CAPA. 1UF 50V 1 C2 NPN CERA.CAPA.CHIP UF 50V 1 C3-6 NPN CHEM. CAPA. 1UF 50V 4 C7-8 NPN CERA.CAPA.CHIP UF 50V 2 C9 NPN CERA.CAPA.CHIP UF 25V 1 CN1 NPN CONNECTOR PHEC40P-R111 1 CN2 NPN CONNECTOR DBLD-J25SAF-21L9-1 1 D1-2 NPN DIODE CHIP MC D3 NPN DIODE CHIP MC D4-5 DSW1 NPN DIP SWITCH 210B008MS 1 IC IC-I/F ST232CWR* 1 S IC2 NPN IC-LIN UPC393G2*T1 1 L1-7 NPN CHIP BEADS IND. BK1608HS601* 7 L8 NPN CHIP RESISTOR 0 OHM 1/16W 1 L9 R1-2 NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R3-4 NPN CHIP RESISTOR 100 OHM 1/16W 2 R5-6 NPN CHIP RESISTOR 10 K-OHM 1/10W 2 R7 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R8 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R9 NPN CHIP RESISTOR 10 K-OHM 1/10W 1 R10 NPN CHIP RESISTOR 100 K-OHM 1/16W 1 R11-12 NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R13 NPN CHIP RESISTOR 100 K-OHM 1/16W 1 R14-15 NPN CHIP RESISTOR 100 OHM 1/16W 2 R16 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R17 NPN CHIP RESISTOR 10 K-OHM 1/10W 1 R18 NPN CHIP RESISTOR 2.7 KOHM 1/16W 1 R19-20 NPN CHIP RESISTOR 10 K-OHM 1/10W 2 R21 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R22 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R23 NPN CHIP RESISTOR 33 K-OHM 1/10W 1 R24 NPN CHIP RESISTOR 3.3 K-OHM 1/10W 1 RA1 NPN RESIS. ARRAY 10 K-OHM 1/8W 8EL 1 TR1 NPN CHIP TRANSISTOR 2SC3875S-G*AL 1 TR2 NPN CHIP TRANSISTOR 2SA1179M6-STR 1 TR3 NPN DIGITAL TRANSISTOR FN1A4P 1 TR4 NPN DIGITAL TRANSISTOR FA1A4P 1 TR5 NPN DIGITAL TRANSISTOR FN1A4P 1 TR6 NPN DIGITAL TRANSISTOR FA1A4P 1 32
37 3-8. Serial Interface Board (9 pin) Circuit Diagram 33
38 Parts List Serial Interface Board (9 pin) DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK C1 NPN CHEM. CAPA. 1UF 50V 1 C2 NPN CERA.CAPA.CHIP UF 50V 1 C3-6 NPN CERA.CAPA.CHIP UF 25V 4 C26-35 R1-2 NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R4-5 NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R6-7 R8 NPN CHIP RESISTOR 0 OHM 1/16W 1 R11-13 NPN CHIP RESISTOR 10 K-OHM 1/16W 3 RA1 NPN RESIS. ARRAY 10 K-OHM 1/8W 8EL 1 IC IC-I/F SP208ECA/TR* 1 S IC2-3 IC4 NPN CMOS TC7WU04FU*12L 1 L1-7 NPN CHIP BEADS IND. BK1608HS601* 7 L8-9 DSW1 NPN DIP SWITCH 210B008MS 1 CN1 NPN CONNECTOR PHEC40P-R111 1 CN2 NPN CONNECTOR 17LE D41 1 CN3 34
39 3-9. USB Interface Board Circuit Diagram 35
40 Parts List USB Interface Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK BC1 NPN CERA.CAPA.CHIP UF 50V 1 BC2A-2C NPN CERA.CAPA.CHIP UF 50V 3 BC3 NPN CERA.CAPA.CHIP UF 25V 1 BC4-5 NPN CERA.CAPA.CHIP UF 50V 2 C01 NPN CERA.CAPA.CHIP UF 10V 1 C02 NPN CERA.CAPA.CHIP UF 50V 1 C03 NPN CHEM. CAPA. CHIP 4.7UF 35V 1 C04 NPN TANTALUM CAPA. CHIP 2.2UF 16V 1 C05 NPN CERA.CAPA.CHIP UF 25V 1 C06 NPN CERA.CAPA.CHIP PF 50V 1 C07 NPN CERA.CAPA.CHIP PF 50V 1 C08 NPN CERA.CAPA.CHIP UF 25V 1 C09-10 C11 NPN CERA. CAPA. CHIP 51PF 50V 1 CN1 NPN CONNECTOR PHEC40P-R111 1 CN2 NPN CONNECTOR V23590-T IC1 NPN IC-RESET M51953BFP*E2 1 IC2 NPN CPU M37640MS-***FP 1 IC3 NPN IC SOCKET IC NPN EPROM A276308AL-70 1 IC4 NPN CMOS 74LV02AFP*EL 1 IC5 NPN CMOS 74LV573AFP*EL 1 IC6 NPN CMOS 74LV1G04ACME* 1 L1-10 NPN CHIP RESISTOR 0 OHM 1/10W 10 RA01-02 NPN RESIS. ARRAY CHIP MNR14J101* 2 RA03-04 RA05 NPN RESIS. ARRAY CHIP MNR14J101* 1 R01 NPN CHIP RESISTOR 1.5 KOHM 1/16W 1 R02-09 NPN CHIP RESISTOR 100 OHM 1/16W 8 R10-11 R12 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R13 R14 NPN CHIP RESISTOR 1.5 KOHM 1/16W 1 R15-16 NPN CHIP RES OHM 1/8W 1% 2 R17 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R18-19 NPN CHIP RESISTOR 10 K-OHM 1/16W 2 R20 NPN CHIP RESISTOR 330 OHM 1/16W 1 R21 NPN CHIP RESISTOR 100 OHM 1/16W 1 R22-26 NPN CHIP RESISTOR 10 K-OHM 1/16W 5 R27 NPN CHIP RESISTOR 330 OHM 1/16W 1 TR1 NPN DIGITAL TRANSISTOR FN1A4P 1 TR2 NPN DIGITAL TRANSISTOR FA1A4P 1 ZD1 NPN ZENER DIODE CHIP NNCD5.6LG*T1 1 XTAL NPN CERA. OSC CHIP EFJC2405E5B* 1 36
41 3-10. Parallel Interface Board Circuit Diagram 37
42 Parts List Parallel Interface Board DRWG.NO. REV. PARTS NO. PARTS NAME Q'TY REMARKS RANK BC1-3 NPN CERA.CAPA.CHIP UF 50V 3 C1 C2 NPN CERA.CAPA.CHIP PF 50V 1 C3-4 C5 NPN CHEM. CAPA. 1UF 50V 1 CN1 NPN CONNECTOR PHEC40P-R111 1 CN2 NPN CONNECTOR 57RE BD29 1 IC TTL IC HD74LS374FP*EL 1 S IC2 NPN TTL IC 74ALS32FP*EL 1 IC TTL IC 74LS05FP*EL 1 S L1-2 NPN CHIP RESISTOR 0 OHM 1/16W 2 L3-4 L CHIP BEADS IND. BK1608HS601* 1 S L6 L7 NPN CHIP RESISTOR 0 OHM 1/16W 1 L8-10 NPN CHIP BEADS IND. BK2125HS470* 3 R1 NPN CHIP RESISTOR 10 K-OHM 1/16W 1 R2-9 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 8 R10 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R11 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R12 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R13 NPN CHIP RESISTOR 100 OHM 1/16W 1 R14 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R15 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R16 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R17 R18 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R19-20 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 2 R21 NPN CHIP RESISTOR 1 K-OHM 1/16W 1 R22 NPN CHIP RESISTOR 4.7 K-OHM 1/16W 1 R23 NPN CHIP RES KOHM 1/16W 5% 1 R24 NPN CHIP RESISTOR 2.2 K-OHM 1/16W 1 R25 NPN CHIP RESISTOR 330 OHM 1/16W 1 RA1 NPN RESIS. ARRAY 4.7K-OHM 1/8W 8EL 1 RA2 NPN RESIS. ARRAY 1.8K-OHM 1/8W 5EL 1 TR1 NPN CHIP TRANSISTOR 2SC3875S-G*AL 1 38
43 ELECTRONIC PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushinya, Shimizu, Shizuoka, Japan Tel : Fax: OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC King Georges Post Road, Edison, NJ U.S.A. Tel : Fax: STAR MICRONICS U.K. LTD. Star House, Peregrine Business Park, Gomm Road, High Wycombe, Bucks, HP13 7DL, U.K. Tel : Fax: Please access the following URL for the lastest revision of the manual. Distributed by Printed in Japan,
DOT MATRIX PRINTER SP320S SERIES TECHNICAL MANUAL [SECOND EDITION]
![DOT MATRIX PRINTER SP320S SERIES TECHNICAL MANUAL [SECOND EDITION]](/thumbs/72/68061967.jpg "DOT MATRIX PRINTER SP320S SERIES TECHNICAL MANUAL [SECOND EDITION]")
DOT MATRIX PRINTER SP320S SERIES TECHNICAL MANUAL [SECOND EDITION] Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 5 Chapter 6 First edition: March 1993 Second edition: March 1997 CONTENTS General Specifications
1 REF PART NO DESCRIPTION REMARKS QTY
Page 1 REF PART NO DESCRIPTION REMARKS QTY 100 1033987 HOUSING ASSY., LOWER 1 102 1033832 COVER, SEALED, REAR 1 103 1033988 HOUSING ASSY., UPPER 1 104 B310204411 C.B.B. SCREW M3X10 12 105 1033813 CAP,
www MK-Electronic de EPSON FX2170 Page 1 of 16
Page 1 of 16 REF. PART.NO. DESCRIPTION QTY STANDARD 100 1025018 HOUSING ASSY. LOWER 1 101 1025039 EDGE GUIDE ASSY. FRONT 1 102 1025041 HOUSING UPPER 1 103 1025027 COVER PRINTER REAR 1 104 1025024 COVER
www MK-Electronic de EPSON STYLUS COLOR 300 Page 1 of 8
Page 1 of 8 REF PART NO STANDARD QTY DESCRIPTION 100 1022993 1 HOUSING, LOWER 101 1004605 4 FOOT 102 1024036 1 SHIELD PLATE, P/S 103 1024201 1 SHIELD PLATE, M/B, UPPER 104 1024202 1 SHIELD PLATE, REAR
www MK-Electronic de EPL5200 Page 1
Page 1 REF NO. PART NO. DESCRIPTION SPECIFICATION QTY 100 1013820 TOP COVER 1 101 1013822 LEFT COVER 1 102 1013821 RIGHT COVER 1 104 1013823 FRONT COVER 1 105 1013819 COVER 1 106 1013824 COVER 1 107 1013828
Number Wheeler P/N Description Set Rex P/N Notes Base 1 J Support, Right 1 J Support, Left 1 J Nut (M8)
1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 4 5 600130 Spring Washer (8mm) 4 6 600344 Roll Pin (M6x30) 4 7 600129 Socket Hd Cap Screw (M8x25) 4 8
Service Manual. COMPACT LINE THERMAL PRINTER CT-S851 Series. Revision
Service Manual COMPACT LINE THERMAL PRINTER CT-S851 Series Revision 1.00 2010.2.25 REVISIONS Rev No. Date Page Comment 1.00 2010/2/25 Newly issued CITIZEN is a registered trademark of CITIZEN HOLDINGS
THERMAL PRINTER. TUP400 Series TECHNICAL MANUAL [ FIFTH EDITION ]
![THERMAL PRINTER. TUP400 Series TECHNICAL MANUAL [ FIFTH EDITION ]](/thumbs/86/94147749.jpg "THERMAL PRINTER. TUP400 Series TECHNICAL MANUAL [ FIFTH EDITION ]")
THERMAL PRINTER TUP00 Series TECHNICAL MANUAL [ FIFTH EDITION ] NOTICE All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR s express permission is forbidden.
Tapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y
W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring
Cleaning the cutter blade
Cleaning the cutter blade < Daily maintenance > In order to use this printer in good condition, please perform the daily maintenance. Note the following when performing the maintenance. Do not lubricate
From the library of: Superior Sewing Machine & Supply LLC
I TER 1 1 Yamajin Bldg., 18, 1-chome, Hon-machi, Higashi-ku, Osaka 541, Japan P.O.Box: Osaka Higashi No. 509 Telephone: Osaka 261-3291 N3297 (7 Lines) Cable Address: "CONSEWMACH" Osaka Telex: J64459 CONSEW
REF. DESCRIPTION VALUE V/W TOL. MFR S DESIG VXSTD P/N VERS. LOT. LAY ADR
Parts List *** MAIN CHASSIS *** C 1 CERAMIC CAP. 0.01uF 50V F DD106F103Z50 K13179008 1 D 1 LED GL8PR21 G2090395 1 D 2 DIODE KBU6D G2090437 1 FH 1 FUSE HOLDER FH-B02 S8101173 1 J 1 CONNECTOR ASSY ELP-04NV
REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
Operating Instructions and Parts Manual Electronic Variable Speed Turret Mill Model JTM-1050EVS
Operating Instructions and Parts Manual Electronic Variable Speed Turret Mill Model JTM-1050EVS JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-690060 Ph.: 800-274-6848 Revision G1 06/2015
Instruction manual SUN-PM100L. SUN-PM100L Polishing Machine English
Instruction manual SUN-PM100L SUN-PM100L Polishing Machine English Table: SUN-UM-TL-PM001 Version: A/0 Fiber Optic Solutions Provider Ⅰ Safety Precautions To ensure safe operation and maximize product
P50 Thermal Printer Owner s Manual
P50 Thermal Printer Owner s Manual CARDINAL SCALE MFG. CO. 8525-M328-O1 Rev B 203 E. Daugherty, Webb City, MO 64870 USA 10/14 Ph:417-673-4631 Fax 417-673-2153 www.detectoscale.com Technical Support: Ph:
ELECTRIC TOOL CORPORATION
Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs
Operating Instructions
Operating Instructions Holding the material against the angle gauge slide it into the forming head. Be sure that the material remains against the gauge until work is finished. NOTE: This machine will handle
Main Components. Pipe and Bolt Threading Machine 300/300A. Early Style. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine 00/00A Main Components Early Style 0 0 * 0 0 0 For Information on Cutters, Die Heads and Reamers SEE INDEX Ref. 0 0 Catalog 0 00 00 0 0 0 00 0 0 0 0 0 0 0 00 0 00 00 00
SFP-550. Operating Manual MATSUHIDAI, MATSUDO-CITY, CHIBA JAPAN TEL: FAX:
SFP-550 Operating Manual 296-1 MATSUHIDAI, MATSUDO-CITY, CHIBA 270-2214 JAPAN TEL: +81-47-388-6111 FAX: +81-47-388-4477 Safety Precautions To ensure safe operation and maximize product service life, observe
Operating Instructions and Parts Manual Step-Pulley Turret Mill Model JVM-836
Operating Instructions and Parts Manual Step-Pulley Turret Mill Model JVM-836 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-690036 Ph.: 800-274-6848 Revision C 11/2014 www.jettools.com
Model 204B-EM Elbow Mandrels Rev TABLE OF CONTENTS
92-0697 Rev. 970131 Model 204B-EM Elbow Mandrels TABLE OF CONTENTS CUSTOMER MESSAGE Inside Front Cover SAFETY PRECAUTIONS 3 GENERAL DESCRIPTION 6 MAINTENANCE 7 OPERATION 8 TROUBLE SHOOTING 11 ACCESSORIES
RATCHET CABLE CUTTER
OPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 764 RATCHET CABLE CUTTER Read and understand this material before operating or servicing this equipment. Failure to understand how to safely operate this
9 Exploded Views and Parts List
9-1 Exploded View G G G Figure9-1 Total Disassembly SAM4S ER-390 SERIES 9-1 A-1 A-2 Figure9-2 ASS Y COVER-PRINTER A. ASS Y COVER-PRINTER No. Parts No. Description / Specification Q`ty Design-Location Serviceable
H4670/42192 Submersible Trash Pump
SERVICE MANUAL H4670/42192 Submersible Trash Pump Serial Code GLW Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 99916070 REV
Bead Roller Operating, Servicing, and Safety Instruction Manual
Bead Roller Operating, Servicing, and Safety Instruction Manual CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. 1-800-67-26 10 Cooperative Way
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27B
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS = Part number change from previous service
ELECTRIC TOOL PARTS LIST
Hitachi Power Tools LIST E936 ELECTRIC TOOL PARTS LIST COMPOUND SAW Model 2004 4 20 (E1) 1 2 3 23 24 7 8 9 10 6 5 4 15 11 16 12 13 12 14 18 25 26 27 28 29 30 19 17 1 9 11 16 21 624 20 22 39 40 41 42 35
REV
Illustrated Parts Breakdown CBR-0 REV.0-030606 WWW.GENECAFE.COM . INTRODUCTION CBR-0 Your Gene Café Illustrated Parts Breakdown(IPB) Manual has been compiled from the latest product information available
OPERATIONS MANUAL. Port-O-Slitter
OPERATIONS MANUAL Port-O-Slitter General instructions, set up, accessories and guide to using your portable precision slitting, rib forming and perforating system Saves hours on large siding jobs! Featuring:
GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING CUT-OFF MACHINE
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
OPERATIONS MANUAL. Port-O-Slitter
Tapco Products Company The World Leader in Specialty Tools for the Professional Port-O-Slitter OPERATIONS MANUAL General instructions, set up, accessories and guide to using your portable precision slitting,
SFP-550. Operating Manual MATSUHIDAI, MATSUDO-CITY, CHIBA JAPAN TEL: FAX:
SFP-550 Operating Manual 296-1 MATSUHIDAI, MATSUDO-CITY, CHIBA 270-2214 JAPAN TEL: +81-47-388-6111 FAX: +81-47-388-4477 Safety Precautions To ensure safe operation and maximize product service life, observe
Operating Instructions and Parts Manual 5-ft. Radial Arm Drill Press Models J-1600R, J-1600R-4
Operating Instructions and Parts Manual 5-ft. Radial Arm Drill Press Models J-1600R, J-1600R-4 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-320038 Ph.: 800-274-6848 Revision H 01/2016
LBI-38392C IC DATA MAINTENANCE MANUAL LOGIC BOARD U707 OCTAL DATA LATCH 19D902172G1 & G2 TABLE OF CONTENTS
LBI-38392C MAINTENANCE MANUAL LOGIC BOARD 19D902172G1 & G2 U707 OCTAL DATA LATCH IC DATA TABLE OF CONTENTS Page DESCRIPTION........................................... Front.. Cover CIRCUIT ANALYSIS........................................
H8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP)
SERVICE MANUAL H8508 Impact Wrench Model 48755 (Serial Code FWN) Model 48760 (Serial Code FWP) Read and understand all of the instructions and safety information in this manual before operating or servicing
PARTS BOOK BQ-140/BQ-51. Perfect Bookbinding Machine. Vol.2 UB /BQ140/08/MO
*UB000-0* PARTS BOOK BQ-0/BQ- Perfect Bookbinding Machine 0/BQ0/0/MO Vol. UB000-0 BQ-0/ Revision Control List Page / Correction (a: Parts No. c: Description d: S/N e: Remarks f: Other g: Registration
ELECTRIC SLIP ROLL MACHINE. Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0
ELECTRIC SLIP ROLL MACHINE Model: ESR-1300X2.5/ESR-1300X4.5 ESR-1550X3.5/ESR-1580X2.0 Operation Manual Table of contents I MAIN SPECIFICATION...2 II SAFETY INSTRUCTIONS.. 2 III OPERATION INSTRUCTIONS..4
11. PARTS LIST 11.1 HEAD STOCK UPSIDE (1) 11-1
11. PARTS LIST 11.1 HEAD STOCK UPSIDE (1) 11-1 HEAD STOCK UPSIDE (1) PARTS LIST NO. PART NO DESCRIPTION QTY 1. SC-M6x20L SOCKET CAP SCREW 4 2. K6-K042-00 TOP BEARING CAP 1 3. 6009LLB BALL BEARING 1 4.
SECTION 9: PARTS G7945/G7946
SECTION 9: PARTS G7945/G7946 Main Parts 22 53 25 26 31 139 32 32-1 60 38 59 38-1 119 35 37 31 38-3 124 125 45A-2 45A-4 45A-1 31 60 45A-3V2 120 121 62 28 28-1 28 27 34 50 51 39 41 126 137 36 46 40 63 33
ELECTRIC TUBE ROLLER
41238-0000 ELECTRIC TUBE ROLLER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 8/20/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,
SAVE THIS MANUAL FOR FUTURE REFERENCE. WARNING: To reduce the risk of
- ($ 0$$/ PP-,( /$( WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Part SP SAVE THIS MANUAL FOR FUTURE REFERENCE Printed in Taiwan
Parts list. From Product number xx MARCH SVP Worldwide - All rights reserved.
Parts list 01 SVP Worldwide - All rights reserved. From Product number 971-xx 0 MARCH 01 A 1 9 7 8 10 1 11 1 1 1 19 18 17 1 0 1 1 7 8 0 1 1 9 1 19810 PRE -TENSION UNIT 17901 REEL PIN 1701 SPRING, REEL
TECHNICAL INFORMATION
TECHNICAL INFORMATION P 1 / 11 Model No. Description CONCEPT AND MAIN APPLICATIONS Specification Standard equipment TCT saw blade... 1 Rear table set (exclusively Europe, Turkey, South Africa..1 2704 This
MODEL RA-200N RADIAL ARM SAW
ITEM NO PART NO DESCRIPTION PRICE 1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900079 CONICAL SPRING 16.3 X 31.5 X 1.2 0.78 3 6940444 OUTER FLANGE 4.49 4 6940443 INNER FLANGE 4.91 5 6100509 PARALLEL
Warm Tube Clock. Before we start, please make sure that you have all required parts that come for the main board :
Warm Tube Clock Assembly Instructions for the main board Introduction Congratulations on your purchase of OSH Nixie Tube Clock. In this document you will see all steps you need to follow in order to successfully
2705 03-09 99 98 97 82 88 89 83 84 85 86 87 101 103 100 106 81 71 105 104 73 74 75 76 77 78 80 79 57 62 58 56 63 65 66 67 68 64 69 70 59 60 61 31 30 29 32 34 35 41 40 42 36 37 38 39 43 4445 46 33 55 54
12. Mechanical Drawings & Parts Breakdown List
12. Mechanical Drawings & Parts Breakdown List Note: When ordering parts, please be prepared with, 1. Machine model & serial number. 2. Item number. 3. Part number and description. 4. Year of Production.
TruTrack Screw-Drive Actuator TKS50
TruTrack Screw-Drive Actuator TKS0 7 4 Parts Sheet 00-4_0_TKS0 4 Not backward compatible with units manufactured before 0/0/00 0 0 7 7 0 4 SOLID NUT SN0 LMI SN0 RP SN0 GH SN0 BRK. 00-00 Head, Idle. 00-04
Copyright 2007 ES Manufacturing, Inc th Street North St. Petersburg, FL 33713
e-mail sales@esmfg.com US/Canada 800-55ES-MFG Documentation & Warranty Packet MB110 ( 600 rpm s) Thank you for purchasing the MB110 If properly operated and maintained, this Heavy Duty Fiber Cutter will
MODEL NO.: MI PARTS BREAKDOWN
MODEL NO.: MI-76350 PARTS BREAKDOWN MAGNUM DRILL PRESS ASSEMBLY INSTRUCTIONS MODEL MI-76350 Before you begin to assemble your drill press, review the parts breakdown and keep it ready for reference. Start
ROUND BENDING MACHINE Model: RBM30
ROUND BENDING MACHINE Model: RBM30 Operation Manual SAVE THIS MANUAL:You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes Model 4000 Shown Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit
24, 36 & 42 Bead Roller Manual
- 1-2, 36 & 2 Bead Roller Manual 1-877-VAN-SANT www.trick-tools.com E:\Product\Product Documentation\0 Bead Roller\Bead Roller Manual\Bead Roller Owners Manual.Doc Rev. 2 3/15/0 JEP SAFETY - 2 - The purpose
Horizontal Band Saw. Operating Instructions and Parts Manual. Models EHB-1018VM EHB-1018VMH
Operating Instructions and Parts Manual Horizontal Band Saw Models EHB-08VM EHB-08VMH JET 427 New Sanford Road LaVergne, Tennessee 37086 www.jettools.com Ph.: 855-336-4032 Part No. M-89070 REV B2 08/204
SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" SLIDING COMPOUND MITER SAW
PAGE 1 OF 6 BASE ASSEMBLY 00 0 CATALOG NO. EXAMPLE: SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 6955-20 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510 M5 x 12mm Flat Head T-20 Screw (5) 3 05-81-0135
3850, Drum & Disc Brake Lathes. Parts Identification
3850, 3860 Drum & Disc Brake Lathes Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for
3000, 4000, 4100, 7500, 7700
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes Model 4000 Shown s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in
SPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 JM21000018 HEX.SOCKET HEAD SCREW M5X12 4 002 JM21000019 SPRING WASHER 5 4 003 JM21000020 FLAT WASHER 5 4 004 JM21000021 UP COVER COMPLETE 1 005 JM21000025 MICRO SWITCH FIX PANEL A 1 006 JM21000026
TUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL
TUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL 1 CONTENTS Page 1. General Information 3 1.1. Introduction 3 1.2. Manufacturer 3 2. Machine s Description and Purpose of Use 3 2.1. Machine s description
FORMAX. FD1400 AutoSeal MAINTENANCE MANUAL FIRST EDITION 11/2007
FORMAX FD1400 AutoSeal 11/2007 MAINTENANCE MANUAL FIRST EDITION Table of Contents 1400 Shown with Optional Stand Page: 1. Description / Unpacking and Set up 2. Controls / Operation 3. Fold Plate Adjustment
Assembly Diagram for DH 50MB
Assembly Diagram for --- 1 --- CODE 1 313-415 FRONT CAP 1 2 318-608 GRIP 1 3 318-590 STOPPER RING 1 4 313-413 NEEDLE HOLDER 1 5 313-419 RETAINER SPRING 1 6 318-589 SPRING HOLDER 1 7 880-810 NYLOCK HEX.
EEBR312A Brake Lathes Parts Identification
EEBR312A Brake Lathes s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference
PARTS. W1669 & W1670 Parts PARTS. Model W1669/W1670 (For Machines Mfd. Since 04/18) 66V A A A 28A
W1669 & W1670 Parts 23 66V2 22 21 25 26 53A 62 63 89 64 9 65 24 20 15 16A 54 93 10 16A-1 81 77 94 53 79 102 103 28 36 8 30 19 31 32 32-1 109 28A 28 27 34 33 56 49 76 76 19-3 19-1 19-2 38-1 89 35 60 59
RYOBI 10 in. (254 mm) TABLE SAW MODEL NO. BT3100 REPAIR SHEET
RYOBI 0 in. (4 mm) TABLE SAW MODEL NO. BT00 REPAIR SHEET FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP FENCE ASSEMBLY, REFER TO FIGURE C FOR MOTOR ASSEMBLY,
How to operate TBC-50
How to operate TBC-50 1. An example (Cutting length : 70mm, Cutting quantity : 120 pcs) Turn on the POWER SW. Set cutting length 70mm. (Press the following buttons in order.) Button "0" has a double functions
LS2-B891 LT2-B892 LS2-B891-05, LT2-B892-05
LS2-B891 LT2-B892 Single Needle Unison Feed Lock Stitcher Single Needle Unison Feed Lock Stitcher with Thread Trimmer Twin Needle Unison Feed Lock Stitcher Twin Needle Unison Feed Lock Stitcher with Thread
XM-502X. SERVICE MANUAL Ver STEREO POWER AMPLIFIER. US Model Canadian Model AEP Model UK Model E Model. Sony Corporation SPECIFICATIONS
XM-502X SERVICE MANUAL Ver 1.1 2001. 08 US Model Canadian Model AEP Model UK Model E Model SPECIFICATIONS Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High
HYDRAULIC CONTROL DETAILS PARTS LIST
Always give model number, serial number and part number when ordering repair parts. HYDRAULIC CONTROL DETAILS PARTS LIST REF NO. PART NUMBER DESCRIPTION 1 101939 Hydraulic Tank 2 101940 Hydraulic Tank
Maintenance Manual CHANNEL GUARD ENCODER/DECODER 19D430740G1 TONE REJECT FILTER 19D430740G4. Mobile Communications
E ********* (REPLACES LBI-4143) Mobile Communications CHANNEL GUARD ENCODER/DECODER 19D430740G1 TONE REJECT FILTER 19D430740G4 Printed in U.S.A. Maintenance Manual TABLE OF CONTENTS SPECIFICATIONS..................................................
Instant MTBF Data Input Sheet Commercial / Bellcore TR Integrated Circuits, Bipolar, Digital
Instant MTBF Data Input Sheet Commercial / Bellcore TR-332 Probabilistic Software, Inc. http://www.e-mtbf.com System / Equipment Name: Assembly Name: Quantity Of This Assembly: Parts List Number: Environment:
12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max)
1 1 2 2 3 3 82mm (Max) 12mm (Max) 12mm (Max) 6mm (Max) 4 4 5 6 8 6mm (Max) 0.5 0mm 1 5 6 7 7 8 9 9 A = B 10 11 12 D B 1 13 14 15 0 C A D E 16 17 18 F G D B N H J G I K 19 A 20 G L 21 C K 1mm L M 1mm 22
MODEL RA-2500N RADIAL ARM SAW
1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900549 WASHER 1.78 3 6080529 ARBOR COLLAR 31.02 4 6760117 OILLESS METAL 1.57 5 9270612 CLAMP SCREW M6 X 12 0.19 6 9220625 HEX. SOCKET HEAD BOLT M6 X 25 0.22
NEWLONG. r PORTABLE FILLED BAG CLOSING MACHINE NEWLONG MACHINE WORKS, LTD.
NEWLONG r PORTABLE FILLED BAG CLOSING MACHINE * NEWLONG MACHINE WORKS, LTD. () THREAD TENSION AND COVER PARTS 0 () THREAD TENSION AND COVER PARTS Ref. No. Part No. Description Q ty Remarks 5 6 7 8 9 0
Model SQM-2AC Squaring Module Rev TABLE OF CONTENTS
92-0714 Rev. 970428 Model SQM-2AC Squaring Module TABLE OF CONTENTS CUSTOMER MESSAGE Inside Front Cover SAFETY PRECAUTIONS 3 GENERAL DESCRIPTION 6 SPECIFICATIONS 7 MAINTENANCE 8 OPERATION 9 CUTTING SPEEDS
Disc, Belt, and Combination Disc/Belt Sanders
This Manual is Bookmarked Operating Instructions Parts Manual Disc, Belt, and Combination Disc/Belt Sanders Models: 4200A, 4300A, 4400A 4200A Disc/Belt Sander 4300A 6 Inch Belt Sander 4400A 12 Inch Disc
6000, Heavy Duty Drum/Disc Lathe. Parts Identification
6000, 6002 Heavy Duty Drum/Disc Lathe Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for
VARIABLE SPEED WOOD LATHE
MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02
535A. Main Components. Pipe and Bolt Threading Machine. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine A Main Components 0 Screw, Button Head /" - 0 x /" () Washer, Flat /" ()" Top Cover 0 Base Bottom Cover Screw, Pan Head # - x " () Carriage Assembly 0 Front Support Bar
RYOBI 10 IN (254 MM) TABLE SAW MODEL NO. BT REPAIR SHEET
RYOBI 0 IN (2 MM) TABLE SAW MODEL NO. BT00- REPAIR SHEET 2 RYOBI 0 in. (2 mm) TABLE SAW - MODEL NO. BT00- FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP
JARVIS. Model H080 Carcass Splitting Band Saw
Carcass Splitting Band Saw EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page... See Table 1, Page 4 Balancer... 4042042 Band Saw Blade... 1023099 Notice to Employer and Safety Director... 2
SFP-550. Maintenance Manual MATSUHIDAI, MATSUDO-CITY, CHIBA JAPAN TEL: FAX:
SFP-550 Maintenance Manual 296-1 MATSUHIDAI, MATSUDO-CITY, CHIBA 270-2214 JAPAN TEL: +81-47-388-6111 FAX: +81-47-388-4477 Introduction This manual covers items and procedures for the periodic inspection
B-Too Drilling and Tapping Machine Instruction and Maintenance Manual
B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our
Main Drive Components
Pipe and Bolt Threading Machine Main Drive Components 0 0 Rear Centering Head Centering Jaw Set Spiral Pins () 00 Centering Scroll Retaining Ring 0 Rear Bearing 0 Oil Ball Valve () # - x / Screw Motor
Instruction Manual for Recipro Handpiece Model: Z-6X #
Instruction Manual for Recipro Handpiece Model: Z-6X #510-2160 Introduction Gesswein Power Hand 2X Recipro handpieces are manufactured to the highest standards available to provide many years of trouble-free
RECIPRO SAW MODEL JR3000V 01-03
RECIPRO SAW MODEL JR3000V 0-03 3 6 7 5 67 8 9 3 0 4 6 66 8 9 0 7 7 3 4 5 6 65 7 8 9 3 3 70 33 34 36 6 37 38 39 4064 4 4 6 59 58 47 46 57 56 48 49 55 5 53 4 73 74 Item Part Qty. Item Part Qty... Used Description..
3000, 4000, 4100, 7500, 7700
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the
RYOBI 10 in. TABLE SAW - MODEL NO. BT3000
FOR MITER TABLE ASSEMBLY, REFER TO FIGURE 0 RYOBI 0 in. TABLE SAW - MODEL NO. BT000 FIGURE 5: 0 in. TABLE SAW FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE FOR RIP FENCE ASSEMBLY, REFER TO FIGURE FOR MOTOR
Repair manual. Fifth-wheel coupling JSK 38/50
Repair manual Fifth-wheel coupling JSK 38/5 ZDE 199 3 12 E 6/212 1 Foreword Table of contents Page Fifth wheel couplings are connecting parts that must comply with very high safety requirements and must
SECTION 9: PARTS. G7947 Stand & Table Breakdown 4V2
SECTION 9: PARTS G7947 Stand & Table Breakdown 19 15 21 18 16 17 112 5 113 3 14 8 7 6 6-1 13 4V2 12 116 11 9 10 2 114 115 1 We do our best to stock replacement parts when possible, but we cannot guarantee
ICF-C112 SERVICE MANUAL FM/AM CLOCK RADIO. E Model. Ver Sony Corporation SPECIFICATIONS
SERVICE MANUAL E Model Ver 1.0 2003. 03 SPECIFICATIONS Time display: 12-hour system Frequency range: : 87.5-108 MHz AM: 530-1710 khz Speaker: Approx. 6.6 cm (2 5/8 inches) dia., 8 ohm Power output: 120
Crimping Dies; PN thru 47825, 47915, and 47918
Crimping Dies; PN 47820 thru 47825, 47915, and 47918 Instruction Sheet 408-1729 22 NOV 16 Rev K Crimping Dies; PN 47820 thru 47825, 47915, and 47918 (Typical) Crimping Die Wire Size Part Number Color Code
Spare part list. For information only, will not be exchanged when altered! Date. piece Rotor 110/115V assy 6. piece Brush holder 100/115V assy 7
cid_etlx V. 0. GIESE 04.04.00 0:3 QuantityUnit Specification Proc.restr. 4 0496 piece Stator 0-V assy 7889 piece Rotor 0/V assy 6 7688 piece Brush holder 00/V assy 7 76999 piece Electronics 0-V 9 7338
Parts List: VBS-3612 Band Saw
Parts List: VBS-3612 Band Saw (refer to breakdowns on pages 35 and 36) Index No. Part No. Description Size Qty 1... VBS3612-101...Gear Box... 1 2... TS-0209101...Socket Head Cap Screw...3/8-16 x 2-1/4...
Onderdelen voor DH50MB
OPTIONAL ACCESSORIES 0 STANDARD ACCESSORIES 0 1 313415 FRONT CAP 1 2 318608 GRIP 1 3 318590 STOPPER RING 1 4 313413 NEEDLE HOLDER 1 5 313419 RETAINER SPRING 1 6 318589 SPRING HOLDER 1 7 880810 NYLOCK HEX.
SPRING MOTOR MD: SERIES 439I2 &44567 CAUTION: DO NOT ALLOW THE CENTER OF A SPRING TO BE PULLED FROM THE COIL. FORM: SM E1 DATE: MAY 15, 1978
SPRING MOTOR MD: FORM: SM0088-03E1 DATE: MAY 15, 1978 SERIES 439I2 &44567 CAUTION: All springs are potentially dangerous and must be handled with care. If it is necessary to disassemble the spring motor,
Crimping Dies for TERMINYL* and PLASTI-GRIP* Terminals and Splices
Crimping Dies for TERMINYL* and PLASTI-GRIP* Terminals and Splices Instruction Sheet 408-10051 11 APR 17 Rev D PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually
Electric Screwdriver Operation Manual. (October, 2018) Transformerless Screwdriver VZ SERIES 100V. Lever Start Type Push To Start Type VZ SERIES 120V
Electric Screwdriver Operation Manual (October, 2018) Transformerless Screwdriver VZ SERIES 100V Lever Start Type Push To Start Type VZ-1510 VZ-1510PS VZ SERIES 120V Lever Start Type Push To Start Type
CATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS FMS40 MIXER ML-134476 ML-134477 ML-141002 FORM 43182 Rev. A (April 2014) F-43182 Rev. A (April 2014) - 2-2014 Table of Contents 5 CONTROL PANEL 7 ELECTRICAL COMPONENTS 9 ATTACHMENT
EllisSaw.com. EllisSaw.com P.O. Box Verona, WI
P.O. Box 9019 Verona, WI 9-019 GENERAL OPERATING & SAFETY INSTRUCTIONS * READ INSTRUCTIONS BEFORE USE * CAUTION: Disconnect power supply cord from power source when doing repair work or changing belt.