PE Document Category: Product Specification
|
|
- Mark Douglas
- 5 years ago
- Views:
Transcription
1 Document Category: Product Specification UltraCMOS, 1 MHz8 GHz Features High 6 GHz Low insertion loss: 6 GHz RF T RISE /T FALL time of 1 ns Power handling of 31 m CW Logic select (LS) pin provides maximum control logic flexibility Terminated all-off state mode 55 C to +125 C operating temperature support Packaging 24-lead mm QFN Applications Harsh industrial applications up to 8 GHz Applications that require extended temperature support in the range of 55 C to +125 C Filter bank switching RF signal routing Figure 1 PE4262 Functional Diagram RF1 RF2 RF3 RFC CMOS Control Driver and ESD V1 V2 V3 RF6 RF5 RF4 switch configuration 5Ω Product Description The PE4262 is a HaRP technology-enhanced absorptive SP6T RF switch that supports a frequency range from 1 MHz to 8 GHz. It delivers low insertion loss, fast RF T RISE /T FALL time, and high isolation in the operating temperature range from 55 C to +125 C. It is ideal for harsh industrial applications that require extended support in this temperature range. No blocking capacitors are required if DC voltage is not present on the RF ports. The PE4262 is manufactured on Peregrine s UltraCMOS process, a patented advanced form of silicon-oninsulator (SOI) technology. Peregrine s HaRP technology enhancements deliver high linearity and excellent harmonics performance. It is an innovative feature of the UltraCMOS process, offering the performance of GaAs with the economy and integration of conventional CMOS. 217, Peregrine Semiconductor Corporation. All rights reserved. Headquarters: 938 Carroll Park Drive, San Diego, CA, Product Specification DOC (3/217)
2 Absolute Maximum Ratings Exceeding absolute maximum ratings listed in Table 1 may cause permanent damage. Operation should be restricted to the limits in Table 2. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. ESD Precautions When handling this UltraCMOS device, observe the same precautions as with any other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the rating specified in Table 1. Latch-up Immunity Unlike conventional CMOS devices, UltraCMOS devices are immune to latch-up. Table 1 Absolute Maximum Ratings for PE4262 Parameter/Condition Min Max Unit Supply voltage, V DD V Digital input voltage (V1, V2, V3, LS) V RF input power (RFCRFX, 5Ω) See Figure 2 m RF input power into terminated ports, CW (1) (RFX, 5Ω) See Figure 2 m Maximum junction temperature + C Storage temperature range + C ESD voltage HBM, all pins (2) 1 V ESD voltage CDM, all pins (3) 1 V Notes: 1) 1% duty cycle, all bands, 5Ω. 2) Human body model (MIL-STD 883 Method 3). 3) Charged device model (JEDEC JESD22-C11). Page 2 DOC (3/217)
3 Recommended Operating Conditions Table 2 lists the recommended operating conditions for the PE4262. Devices should not be operated outside the recommended operating conditions listed below. Table 2 Recommended Operating Conditions for PE4262 Parameter Min Typ Max Unit Supply voltage, V DD V Supply current, I DD 12 2 µa Digital input high (V1, V2, V3, LS) V Digital input low (V1, V2, V3, LS).3.6 V Digital input current V1, V2, V3 LS 5 1 µa µa RF input power, CW (RFCRFX) (1) See Figure 2 m RF input power, pulsed (RFCRFX) (2) See Figure 2 m RF input power into terminated ports, CW (RFX) (1) See Figure 2 m Operating temperature range C Notes: 1) 1% duty cycle, all bands, 5Ω. 2) Pulsed, 5% duty cycle of 2 µs period, 5Ω. DOC (3/217) Page 3
4 Electrical Specifications Table 3 provides the PE4262 key electrical specifications at +25 C,V DD = 3.3V (Z S = Z L = 5Ω), unless otherwise specified. Table 3 PE4262 Electrical Specifications Parameter Path Condition Min Typ Max Unit Operating frequency 1 MHz 8 GHz Insertion loss (1) Isolation (1) RFCRF1/6 RFCRF2/5 RFCRF3/4 RFCRF1/6 RFCRF2/5 RFCRF3/4 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz As shown Page 4 DOC (3/217)
5 Table 3 PE4262 Electrical Specifications (Cont.) Parameter Path Condition Min Typ Max Unit Return loss (active port) Return loss (RFC port) RFCRF1/6 RFCRF2/5 RFCRF3/4 RFCRF1/6 RFCRF2/5 RFCRF3/4 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz DOC (3/217) Page 5
6 Table 3 PE4262 Electrical Specifications (Cont.) Parameter Path Condition Min Typ Max Unit Return loss (terminated port) Relative insertion phase (2) Input 1 compression point (3) Input.1 compression point (3) RF1/6 RF2/5 RF3/4 RF2RF1 (RF5RF6) RF3RF1 (RF4RF6) RFCRFX RFCRFX 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 1 GHz 2 GHz 4 GHz 6 GHz 8 GHz 1 GHz 2 GHz 4 GHz 6 GHz 8 GHz See Figure 2 See Figure 2 Input IP2 RFCRFX 1 MHz8 GHz m Input IP3 RFCRFX 1 MHz8 GHz 6 m RF T RISE /T FALL 1%/9% RF 1 13 ns Settling time 5% CTRL to.5 final value ns Switching time 5% CTRL to 9% or 1% of RF ns Notes: 1) Insertion loss and isolation performance can be improved by a good RF ground on the LS pin (pin 1). 2) Defined with S-parameters, relative insertion phase (RFXRF1) = S (x+1)1 S 21, where incident Port-1 is RFC, response Port-2 = RF1, and response Port-(x+1) = RFx. 3) The input 1 and.1 compression points are linearity figures of merit. Refer to Table 2 for the RF input power (5Ω) Deg Deg Deg Deg Deg Deg Deg Deg Deg Deg m m Page 6 DOC (3/217)
7 Switching Frequency The PE4262 has a maximum 25 khz switching frequency. Switching frequency describes the time duration between switching events. Switching time is the time duration between the point the control signal reached 5% of the final value and the point the output signal reaches within 1% or 9% of its target value. Spurious Performance The PE4262 spur fundamental occurs around 5 MHz. Its typical performance is 162 m/hz, with 3 khz bandwidth. Hot-Switching Capability The maximum hot switching capability of the PE4262 is 18 m above 1 MHz. Hot switching occurs when RF power is applied while switching between RF ports. Thermal Data Psi-JT (Ψ JT ), junction top-of-package, is a thermal metric to estimate junction temperature of a device on the customer application PCB (JEDEC JESD-2). Ψ JT = (T J T T )/P where Ψ JT = junction-to-top of package characterization parameter, C/W T J = die junction temperature, C T T = package temperature (top surface, in the center), C P = power dissipated by device, Watts Table 4 Thermal Data for PE4262 Parameter Typ Unit Ψ JT 23 C/W Θ JA, junction-to-ambient thermal resistance 63 C/W DOC (3/217) Page 7
8 Control Logic Table 5 provides the control logic truth table for PE4262. Table 5 Truth Table for PE4262 LS (1) V3 V2 V1 RFCRF1 RFCRF2 RFCRF3 RFCRF4 RFCRF5 RFCRF6 ON OFF OFF OFF OFF OFF 1 OFF ON OFF OFF OFF OFF 1 OFF OFF ON OFF OFF OFF 1 1 OFF OFF OFF ON OFF OFF 1 OFF OFF OFF OFF ON OFF 1 1 OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF 1 1 OFF ON OFF OFF OFF OFF OFF OFF ON OFF OFF OFF 1 1 OFF OFF OFF ON OFF OFF 1 1 OFF OFF OFF OFF ON OFF 1 OFF OFF OFF OFF OFF ON X (2) 1 1 OFF OFF OFF OFF OFF OFF Notes: 1) LS has an internal 1 MΩ pull-up resistor to logic high. Connect LS to externally to generate a logic. Leaving LS floating will generate a logic 1. 2) LS = don t care, V3 =, V2 = V1 = 1, all ports are terminated to provide an all isolated state. Page 8 DOC (3/217)
9 Power De-rating Curve Figure 2 shows the power de-rating curve showing P1 compression, P.1 compression, maximum RF input power (pulsed), maximum RF input power (CW), absolute maximum RF terminated power (CW), and maximum RF terminated power (CW). Figure 2 Power De-rating Curve, 1 MHz8 GHz, 55 C to +125 C Ambient, 5Ω P1 25 C Ambient/Abs. Max. RF Input Power P.1 25 C Max. RF Input Power, Pulsed Max. RF Input Power, CW Abs. Max. RF Terminated Power, CW Max. RF Terminated Power, CW Input Power (m) Frequency (MHz) DOC (3/217) Page 9
10 Isolation Matrix Table 6 provides RFC-to-port isolation and Table 7 provides port-to-port isolation at +25 C, V DD = 3.3V (Z S = Z L = 5Ω). Table 6 RFC-to-Port Isolation ON Port RF1 RF2 RF3 RF4 RF5 RF6 Frequency 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz Isolation () RF1 RF2 RF3 RF4 RF5 RF Page 1 DOC (3/217)
11 Table 7 Port-to-Port Isolation ON Port Frequency Isolation () RF1 RF2 RF3 RF4 RF5 RF6 RF1 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz RF2 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz RF3 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz RF4 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz RF5 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz RF6 11 MHz 1 MHz1 GHz 12 GHz 24 GHz GHz 68 GHz DOC (3/217) Page 11
12 Typical Performance Data Figure 3Figure 2 show the typical performance data at +25 C,V DD = 3.3V (Z S = Z L = 5Ω), unless otherwise specified. Figure 3 Insertion Loss vs. Frequency (RFCRFX) Figure 5 Insertion Loss vs. Frequency Over V DD (RFCRF1) if Insertion Loss () RFC-RF1 RFC-RF2 RFC-RF3 RFC-RF4 RFC-RF5 RFC-RF Insertion Loss () V 3.3V 5.5V Figure 4 Insertion Loss vs. Frequency Over Temperature (RFCRF1) Figure 6 RFC Port Return Loss vs. Frequency -55 C +25 C +125 C RF1 On RF2 On RF3 On Insertion Loss () Return Loss () RF4 On RF5 On RF6 On Page 12 DOC (3/217)
13 Figure 7 RFC Port Return Loss vs. Frequency Over Temperature (RF1 On) Figure 1 RF1 Active Port Return Loss vs. Frequency Over Temperature -55 C +25 C +125 C -55 C +25 C +125 C Return Loss () Return Loss () Figure 8 RFC Port Return Loss vs. Frequency Over V DD (RF1 On) Figure 11 RF1 Active Port Return Loss vs. Frequency Over V DD 2.3V 3.3V 5.5V 2.3V 3.3V 5.5V Return Loss () Return Loss () Figure 9 Active Port Return Loss vs. Frequency Figure 12 Terminated Port Return Loss vs. Frequency (RF1 On) Return Loss () RF1 RF2 RF3 RF4 RF5 RF6 Return Loss () RF2 RF3 RF4 RF5 RF DOC (3/217) Page 13
14 Figure 13 RF2 Terminated Port Return Loss vs. Frequency Over Temperature (RF1 On) Figure 16 Isolation vs. Frequency Over V DD (RF1RF2, RF1 On) Return Loss () C +25 C +125 C Isolation () V 3.3V 5.5V Figure 14 RF2 Terminated Port Return Loss vs. Frequency Over V DD (RF1 On) Figure 17 Isolation vs. Frequency Over Temperature (RFCRF2, RF1 On) 2.3V 3.3V 5.5V -55 C +25 C +125 C Return Loss () Isolation () Figure Isolation vs. Frequency Over Temperature (RF1RF2, RF1 On) Figure 18 Isolation vs. Frequency Over V DD (RFCRF2, RF1 On) -55 C +25 C +125 C 2.3V 3.3V 5.5V Isolation () Isolation () Page 14 DOC (3/217)
15 Figure 19 IIP2 vs. RF Port Measured Figure 2 IIP3 vs. RF Port Measured IIP2 (m) MHz IIP2 2 GHz IIP2 4 GHz IIP2 8 GHz IIP2 RF1 RF2 RF3 RF4 RF5 RF6 RF Port Measured IIP3 (m) MHz IIP3 2 GHz IIP3 4 GHz IIP3 8 GHz IIP3 RF1 RF2 RF3 RF4 RF5 RF6 RF Port Measured DOC (3/217) Page
16 Evaluation Kit The high-throw count RF switch evaluation kit (EVK) includes hardware required to control and evaluate the functionality of the high-throw count switches. The high-throw count RF switch evaluation software can be downloaded at and requires a PC running Windows operating system to control the USB interface board. Refer to the Multi-throw Count RF Switch Evaluation Kit (EVK) User s Manual for more information. Figure 21 Evaluation Board Layout for PE4262 Page 16 DOC (3/217)
17 Pin Information This section provides pinout information for the PE4262. Figure 22 shows the pin map of this device for the available package. Table 8 provides a description for each pin. Figure 22 Pin Configuration (Top View) Table 8 Pin Descriptions for PE4262 Pin No. Pin Name 1 LS 2 RF2 (1) RF port 2 Description Logic Select used to determine the definition for V1, V2 and V3 pins Pin 1 Dot Marking RF1 RFC NC RF6 3,, 12 14, 16, 18, 21, 23 Ground LS RF2 RF Exposed Ground Pad RF5 RF4 4 RF3 (1) RF port 3 8 V DD Supply voltage (nominal 3.3V) 9 V1 Digital control logic input 1 1 V2 Digital control logic input 2 11 V3 Digital control logic input RF4 (1) RF port RF5 (1) RF port RF6 (1) RF port 6 V DD V1 V2 V3 2 NC (2) No connect 22 RFC (1) RF common port 24 RF1 (1) RF port 1 Pad Exposed pad: ground for proper operation Notes: 1) RF pins 2, 4,, 17, 19, 22 and 24 must be at VDC. The RF pins do not require DC blocking capacitors for proper operation if the VDC requirement is met. 2) Pin 2 (NC) can be connected to or left not connected externally. DOC (3/217) Page 17
18 Packaging Information This section provides packaging data including the moisture sensitivity level, package drawing, package marking and tape-and-reel information. Moisture Sensitivity Level The moisture sensitivity level rating for the PE4262 in the 24-lead mm QFN package is MSL1. Package Drawing Figure 23 Package Mechanical Drawing for 24-lead mm QFN B A 4..1 C (2X).5 (x2) ± ±.5 (x24).6 (x24).3 (x24).5 (x2) ± C (2X) Pin #1 Corner.25±.5 (x24) Ref Chamfer.3 x TOP VIEW BOTTOM VIEW RECOMMENDED LAND PATTERN.1 C.5 C SEATING PLANE.85±.5.1 C A B.5 C ALL FEATURES.23 Ref. SIDE VIEW.5 C Top-Marking Specification Figure 24 Package Marking Specifications for PE YYWW ZZZZZZ = YY = WW = ZZZZZZ = Pin 1 indicator Last two digits of assembly year Assembly work week Assembly lot code (Maximum six characters) Page 18 DOC (3/217)
19 Tape and Reel Specification Figure 25 Tape and Reel Specifications for 24-lead mm QFN Direction of Feed Section A-A T P see note 1 P1 P2 see note 3 D1 D A E F see note 3 B K A A W A B K D D1 E F P P1 P2 T W / min 1.75 ± ± ±.5.3 ± ±.3 Notes: 1. 1 Sprocket hole pitch cumulative tolerance ±.2 2. Camber in compliance with EIA Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole Dimensions are in millimeters unless otherwise specified Pin 1 Device Orientation in Tape DOC (3/217) Page 19
20 Ordering Information Table 9 lists the available ordering codes for the PE4262 as well as available shipping methods. Table 9 Order Codes for PE4262 Order Codes Description Packaging Shipping Method PE4262A-X PE4262 SP6T RF switch Green 24-lead 4 4 mm QFN 5 units/t&r EK PE4262 Evaluation kit Evaluation kit 1/Box Document Categories Advance Information The product is in a formative or design stage. The datasheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The datasheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The datasheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a CNF (Customer Notification Form). Sales Contact For additional information, contact Sales at sales@psemi.com. Disclaimers The information in this document is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user s own risk. No patent rights or licenses to any circuits described in this document are implied or granted to any third party. Peregrine s products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. Patent Statement Peregrine products are protected under one or more of the following U.S. patents: patents.psemi.com Copyright and Trademark 217, Peregrine Semiconductor Corporation. All rights reserved. The Peregrine name, logo, UTSi and UltraCMOS are registered trademarks and HaRP, MultiSwitch and DuNE are trademarks of Peregrine Semiconductor Corp. Product Specification DOC (3/217)
PE42482 Document Category: Product Specification
Document Category: Product Specification UltraCMOS, 1 MHz8 GHz Features High isolation: @ 6 GHz Low insertion loss: 1.1 @ 6 GHz Fast switching time of 227 ns Power handling of m CW Logic select (LS) pin
More informationPE42412 Document Category: Product Specification
PE2 Document Category: Product Specification UltraCMOS, 1 MHz8 GHz Features High isolation: @ 6 GHz Low insertion loss: 1.3 @ 6 GHz Fast switching time of 2 ns Power handling of m CW Logic select (LS)
More informationPE42562 Document Category: Product Specification
Document Category: Product Specification UltraCMOS, 9 khz8 GHz Features High isolation: @ 6 GHz Low insertion loss: 1.1 @ 6 GHz Fast switching time of 21 ns Power handling of 33 m CW Logic select (LS)
More informationPE42582 Document Category: Product Specification
Document Category: Product Specification UltraCMOS, 9 khz8 GHz Features High isolation: @ 6 GHz Low insertion loss: 1.1 @ 6 GHz Fast switching time of 227 ns Power handling of m CW Logic select (LS) pin
More informationPE42512 Document Category: Product Specification
PE2 Document Category: Product Specification UltraCMOS, 9 khz8 GHz Features High isolation: @ 6 GHz Low insertion loss: 1.3 @ 6 GHz Fast switching time of 2 ns Power handling of m CW Logic select (LS)
More informationPE42823 Document Category: Product Specification
Document Category: Product Specification UltraCMOS, 7 MHz 6 GHz Features Excellent single-event peak power handling of 51 m LTE Exceptional linearity performance across all frequencies Input IP3: 7 m Input
More informationPE42020 Product Specification
Product Specification, Hz 8 MHz Features High power handling 3 m @ DC 36 m @ 8 GHz Maximum voltage (DC or AC peak): ±1V on the RF ports Total harmonic distortion (THD): 84 c Configurable 5Ω absorptive
More informationProduct Specification PE42821
Product Description The is a HaRP technology-enhanced high power reflective SPDT RF switch designed for use in mobile radio, relay replacement and other high performance wireless applications. This switch
More informationProduct Specification PE42520
PE42520 Product Description The PE42520 SPDT absorptive RF switch is designed for use in Test/ATE and other high performance wireless applications. This broadband general purpose switch maintains excellent
More informationProduct Specification PE42442
PE42442 Product Description The PE42442 is a HaRP technology-enhanced absorptive SP4T RF switch designed for use in 3G/4G wireless infrastructure and other high performance RF applications. This switch
More informationProduct Specification PE42851
PE42851 Product Description The PE42851 is a HaRP technology-enhanced SP5T high power RF switch supporting wireless applications up to 1 GHz. It offers maximum power handling of 42.5 m continuous wave
More informationProduct Specification PE42850
Product Description The PE4850 is a HaRP technology-enhanced SP5T high power RF switch supporting wireless applications up to GHz. It offers maximum power handling of 4.5 m continuous wave (CW). It delivers
More informationProduct Specification PE42540
PE42540 Product Description The PE42540 is a HaRP technology-enhanced absorptive SP4T RF switch developed on UltraCMOS process technology. This switch is designed specifically to support the requirements
More informationProduct Specification PE42452
Product Description The PE42452 is a HaRP technology-enhanced absorptive SP5T RF switch designed for use in 3G/4G wireless infrastructure and other high performance RF applications. This switch is a pin-compatible
More informationPE43712 Product Specification
Product Specification, 9 khz 6 GHz Features Flexible attenuation steps of.25,.5 and 1 up to 31.75 Glitch-less attenuation state transitions Monotonicity:.25 up to 4 GHz,.5 up to 5 GHz and 1 up to 6 GHz
More informationOBSOLETE. 9 khz. Operation Frequency 9 khz. db 6000 MHz. db Return Loss RF1, RF2 and RFC
Product Description The PE455 RF Switch is designed to support the requirements of the test equipment and ATE market. This broadband general purpose switch maintains excellent RF performance and linearity
More informationProduct Specification PE42920
PE42920 Product Description The PE42920 is a dual differential single pole double throw (DDSPDT) RF switch developed on Peregrine s UltraCMOS process technology. It is a broadband and low loss device enabling
More informationProduct Specification PE45450
PE45450 Product Description The PE45450 is a HaRP technology-enhanced power limiter designed for use in high performance power limiting applications in test and measurement equipment, radar, military electronic
More informationPE Product Specification. Product Description. 75 Ω Terminated MHz SPDT CATV UltraCMOS Switch Featuring Unpowered Operation
Product Description The PE4275 is an SPDT UltraCMOS Switch designed for Broadband applications such as CATV, DTV, Multi- Tuner Digital Video Recorder (DVR ), Set-top Box, PCTV and Video Game Consoles.
More informationPE4257. Product Specification. Product Description
Product Description The PE is a high-isolation UltraCMOS Switch designed for wireless applications, covering a broad frequency range from near DC up to 000 MHz. This single-supply SPDT switch integrates
More informationPE Product Specification. SP5T Absorptive UltraCMOS High-Isolation RF Switch MHz, Vss EXT option. Product Description
Product Description The PE445 is a HaRP -enhanced Absorptive SP5T RF Switch developed on the UltraCMOS process technology. This general purpose switch is comprised of five symmetric RF ports and has very
More informationOBSOLETE REPLACE WITH PE4259 PE4283. Product Specification. Product Description
Product Description The PE4283 RF Switch is designed to cover a broad range of applications from DC through 4000 MHz. This reflective switch integrates on-board CMOS control logic with a low voltage CMOS-compatible
More informationREPLACE WITH PE43205 PE Switched Attenuator Array. Product Specification. RF InputOBSOLETE. RF Output. Parallel Control. Control Logic Interface
Product Description The PE30 is a 50Ω, HaRP -enhanced, high linearity, -bit RF Digital Step Attenuator (DSA) covering an 8 db attenuation range in db steps. With a parallel control interface, it maintains
More informationOBSOLETE. RF Output DOC-02145
Product Description The PE436 is a high linearity, 5-bit RF Digital Step Attenuator (DSA) covering a 3 db attenuation range in db steps, and is pin compatible with the PE43x series. This 5-ohm RF DSA provides
More informationProduct Specification PE94302
Product Description Peregrine s is a high linearity, 6-bit UltraCMOS RF digital step attenuator (DSA). This 50Ω RF DSA covers a 31.5 db attenuation range in 0.5 db steps. It provides both parallel and
More informationPE29102 Document Category: Product Specification
Document Category: Product Specification UltraCMOS, 40 MHz Features High- and Low-side FET drivers Dead-time control Fast propagation delay, 9 ns Tri-state enable mode Sub-nanosecond rise and fall time
More informationProduct Specification PE9311
PE93 Product Description The PE93 is a high-performance static UltraCMOS prescaler with a fixed divide ratio of. Its operating frequency range is DC to 500 MHz. The PE93 operates on a nominal 3V supply
More informationObsolete db db Input IP dbm Input 1 db Compression 21 dbm
Product Description The PE4135 is a high linearity passive Quad MOSFET Mixer for GSM8 & Cellular Base Station Receivers, exhibiting high dynamic range performance over a broad drive range of up to 2 dbm.
More informationPE Advance Information. Product Description
Product Description The PE43702 is a HaRP -enhanced, high linearity, 7-bit RF Digital Step Attenuator (DSA) covering a 31.75 db attenuation range in 0.25 db steps. This Peregrine 50Ω RF DSA provides both
More informationPE4141. Product Specification. Ultra-linear UltraCMOS Broadband Quad MOSFET Array. Product Description
Product Description The PE4141 is an ultra-high linearity passive broadband Quad MOSFET array with high dynamic range performance capable of operation up to 1.0 GHz. This quad array operates with differential
More informationOBSOLETE REPLACE WITH PE43711 PE Product Specification. Product Description
Product Description he PE6 is a HaRP -enhanced, high linearity, 6-bit RF Digital Step Attenuator (DSA) covering a. db attenuation range in. db steps. his Peregrine Ω RF DSA provides both a serial and parallel
More informationOBSOLETE REPLACE WITH PE43712 PE Product Specification. Product Description
Product Description The PE4371 is a HaRP -enhanced, high linearity, 7-bit RF Digital Step Attenuator (DSA). This highly versatile DSA covers a 31.75 db attenuation range in.25 db steps. The Peregrine 5Ω
More informationSKY LF: 0.02 to 4.0 GHz High Isolation SP4T Absorptive Switch with Decoder
DATA SHEET SKY13392-359LF:.2 to 4. GHz High Isolation SP4T Absorptive Switch with Decoder Applications GSM/CDMA/WCDMA/LTE cellular infrastructure Test and measurement systems Military communications Features
More informationSKY LF: 20 MHz-6.0 GHz GaAs SP4T Switch
DATA SHEET SKY13322-375LF: 2 MHz-6. GHz GaAs SP4T Switch Applications Multiband telecommunications up to 6 GHz Features Broadband frequency range: 2 MHz to 6. GHz Low insertion loss:.45 @ 1 GHz Very high
More informationSKY LF: 0.1 to 6.0 GHz High Isolation SPDT Absorptive Switch
DATA SHEET SKY13286-359LF:.1 to 6. GHz High Isolation SPDT Absorptive Switch Applications GSM, PCS, WCDMA base stations 2.4 and 5.8 GHz ISM devices Wireless local loops CBL 5 Features CBL RFC Single, positive
More informationPE Product Specification. UltraCMOS Integer-N PLL Frequency Synthesizer for Low Phase Noise Applications
Product Description Peregrine s PE33241 is a high-performance Integer-N PLL capable of frequency synthesis up to 5 GHz. This device is designed for use in industrial and military applications, point-to-point
More informationProduct Specification PE64908
Product Description PE64908 is a DuNE technology-enhanced Digitally Tunable Capacitor (DTC) based on Peregrine s UltraCMOS technology.this highly versatile product supports a wide variety of tuning circuit
More informationProduct Specification PE64906
PE6496 Product Description PE6496 is a DuNE technology-enhanced digitally tunable capacitor (DTC) based on Peregrine s UltraCMOS technology. This highly versatile product supports a wide variety of tuning
More informationProduct Specification PE64909
PE6499 Product Description PE6499 is a DuNE technology-enhanced Digitally Tunable Capacitor (DTC) based on Peregrine s UltraCMOS technology. This highly versatile product supports a wide variety of tuning
More informationOBSOLETE OUT. Output Buffer. Supply Voltage V. Supply Current 8 12 ma
Product Description The PE3513 is a high-performance static UltraCMOS prescaler with a fixed divide ratio of 8. Its operating frequency range is DC to 1500 MHz. The PE3513 operates on a nominal 3 V supply
More informationSKY LF: 0.01 to 6.0 GHz Single Control SP2T Switch
DATA SHEET SKY13453-385LF: 0.01 to 6.0 GHz Single Control SP2T Switch Applications RFC Cellular pre-pa mode switches Dual-band WLANs (802.11a/b/g/n) Features RF1 RF2 Low insertion loss: 0.40 @ 2.0 GHz
More informationProduct Specification PE42540
PE4540 Product Description The PE4540 is a HaRP technology-enhanced absorptive SP4T RF switch developed on UltraCMOS process technology. This switch is designed specifically to support the requirements
More informationPE3282A. 1.1 GHz/510 MHz Dual Fractional-N PLL IC for Frequency Synthesis. Peregrine Semiconductor Corporation. Final Datasheet
Final Datasheet PE3282A 1.1 GHz/510 MHz Dual Fractional-N PLL IC for Frequency Synthesis Applications Cellular handsets Cellular base stations Spread-spectrum radio Cordless phones Pagers Description The
More informationSKY LF: 0.35 to 4.0 GHz Two-Bit Digital Attenuator
DATA SHEET SKY12355-337LF: 0.35 to 4.0 GHz Two-Bit Digital Attenuator Applications Cellular infrastructure Wireless receivers RF1 Features Positive voltage operation with integrated decoder CTL1 6 Broadband
More informationObsolete PE Product Specification. Product Description
Product Description The PE5 is a HaRP -enhanced, high linearity, 5-bit RF Digital Step Attenuator (DSA). This highly versatile DSA covers a 7.75 db attenuation range in.5 db steps. The Peregrine 5Ω RF
More informationOBSOLETE. RF Output. Parameter Test Conditions Frequency Minimum Typical Maximum Units
Product Description The PE438 is a high linearity, 5-bit RF Digital Step Attenuator (DSA) covering 31 db attenuation range in 1dB steps, and is pin compatible with the PE43x series. This 75-ohm RF DSA
More informationQPC6054SR. Product Description. Product Features. Functional Block Diagram. Applications. Ordering Information
RFC VSS/ V3 Product Description The is a Silicon on Insulator (SOI) single-pole, 5- throw (SP5T) switch design for use in cellular, 3G, LTE and other high performance communications systems. It offers
More informationOBSOLETE REPLACE WITH PE43712 PE Product Specification. Product Description
Product Description The PE6 is a HaRP -enhanced, high linearity, 6-bit RF Digital Step Attenuator (DSA). This highly versatile DSA covers a 5.75 db attenuation range in.5 db steps. The Peregrine 5Ω RF
More informationSKY LF: 20 MHz-5 GHz, 7 W SPDT Switch
DATA SHEET SKY13299-321LF: 2 MHz-5 GHz, 7 W SPDT Switch Applications RFC WiMAX and WLAN systems Features VCTL1 J1 VCTL2 J2 Positive voltage operation: /3 to /5 V Low insertion loss:.5 typical @ 3.5 GHz
More informationPE Product Specification RF- RF+ CMOS Control Driver and ESD. Product Description. UltraCMOS Digitally Tunable Capacitor (DTC) MHz
Product Description The PE6494 is a DuNE -enhanced Digitally Tunable Capacitor (DTC) based on Peregrine s UltraCMOS technology. DTC products provide a monolithically integrated impedance tuning solution
More informationSKY LF: 0.05 to 2.7 GHz SP4T Switch with Integrated Logic Decoder
DATA SHEET SKY13388-465LF:.5 to 2.7 GHz SP4T Switch with Integrated Logic Decoder Applications WCDMA/CDMA/LTE front-end/antenna switches Diversity receive antenna switches ANT Features Broadband frequency
More informationSKY LF: 0.1 to 3.5 GHz SP3T Switch
DATA SHEET SKY13345-368LF: 0.1 to 3.5 GHz SP3T Switch Applications 802.11 b/g WLANs Bluetooth J3 V3 Features Broadband frequency range: 0.1 to 3.5 GHz Low insertion loss: 0.5 @ 2.45 GHz High isolation:
More informationObsolete PE3336. Product Specification. Product Description. 3 GHz UltraCMOS Integer-N PLL for Low Phase Noise Applications
Product Description Peregrine s PE3336 is a high performance integer-n PLL capable of frequency synthesis up to 3 GHz. The superior phase noise performance of the PE3336 makes it ideal for applications
More informationCLA LF: Surface Mount Limiter Diode
DATA SHEET CLA4610-085LF: Surface Mount Limiter Diode Applications Low-loss, high-power limiters Receiver protectors Anode (Pin 1) Anode (Pin 3) Features Low thermal resistance: 73 C/W Typical threshold
More informationSPDT RF Switch RF Switch with internal driver Single Supply Voltage, +2.3V to +5.5V
High Power RF Switch with internal driver Single Supply Voltage, +2.3V to +5.5V The Big Deal High power handling, 32W @ 850 MHz - Pulsed High IIP3, +81 m Immune to latch-up CASE STYLE: JY2179 Product Overview
More informationPreliminary Datasheet
Product Description The is an absorptive SPDT 50Ω matched RF switch supporting bandwidths up to 6GHz. Its high linearity performance across the temperature range makes it ideally suited for use in 3G/4G/5G
More informationSKY LF: 0.5 to 6.0 GHz SPDT Switch, 50 Ω Terminated
DATA SHEET SKY13370-374LF: 0.5 to 6.0 GHz SPDT Switch, 50 Ω Terminated Applications WiMAX 802.16 Dual-band WLANs (802.11 a/b/g/n) LTE/4G systems Features RF1 50 Ω 50 Ω RF2 50 Ω matched RF ports in all
More informationSKY LF: 0.1 to 6.0 GHz GaAs SPDT Switch
DATA SHEET SKY13320-374LF: 0.1 to 6.0 GHz GaAs SPDT Switch Applications Two-way radios WiMAX WLANs J2 J1 Features Broadband frequency range: 0.1 to 6.0 GHz Low insertion loss: 0.5 @ 2.4 GHz High isolation:
More informationSKY LF: GHz GaAs SPDT Switch
DATA SHEET SKY13321-36LF:.1-3. GHz GaAs SPDT Switch Applications Higher power applications with excellent linearity performance RFC WiMAX systems J2 J1 Features Positive voltage control ( to 1.8 V) High
More informationSKYA21024: 0.01 to 6.0 GHz Single Control SPDT Switch
DATA SHEET SKYA21024: 0.01 to 6.0 GHz Single Control SPDT Switch Applications Automotive WLAN 802.11 a/b/g/n/ac WLAN repeaters ISM band radios Low power transmit receive systems Automotive infotainment
More informationSKY LF: GHz SP3T Switch, 50 Ω Terminated
DATA SHEET SKY13408-465LF: 1.0 6.0 GHz SP3T Switch, 50 Ω Terminated Applications WiMAX 802.16 Dual-band WLANs (802.11 a/b/g/n) LTE/4G systems WLAN 802.11a/c 5 GHz video distribution Features 50 Ω matched
More informationSKY LF: GHz Four-Bit Digital Attenuator (1 db LSB)
DATA SHEET SKY12348-35LF:.1-3. GHz Four-Bit Digital Attenuator (1 LSB) Applications RF2 Cellular, 3G/4G, WiMAX, and LTE Infrastructures RF and IF systems Features Broadband operation:.1 to 3. GHz Attenuation:
More informationPE4140. Product Specification. Ultra-High Linearity UltraCMOS Broadband Quad MOSFET Array. Product Description
Product Description The PE0 is an ultra-high linearity passive broadband Quad MOSFET array with high dynamic range performance capable of operation beyond 6.0 GHz. This quad array operates with differential
More informationOBSOLETE PE4150. Product Specification. UltraCMOS Low Frequency Passive Mixer with Integrated LO Amplifier. Product Description
Product Description The PE45 is an ultra-high linearity Quad MOSFET mixer with an integrated LO amplifier. The LO amplifier allows for LO drive levels of less than dbm to produce IIP values similar to
More informationSPDT RF Switch JSW2-63VHDRP+
High Power SPDT RF Switch RF Switch with internal driver Single Supply Voltage, +2.3V to +5.5V The Big Deal High power handling, 2.5W @2 GHz High IIP3, +75 m Low insertion loss, 0.4 Fast switching, 2µs
More informationSKYA21029: 0.1 to 3.8 GHz SP4T Antenna Switch
DATA SHEET SKYA21029: 0.1 to 3.8 GHz SP4T Antenna Switch Applications 2G/3G/4G/4G LTE, 4G LTE-A Embedded cellular telematics modules OBD-II cellular modems RF1 Features RF2 Broadband frequency range: 0.1
More informationSKY LF: 2.2 to 2.8 GHz Two-Way, 0 Degrees Power Divider
DATA SHEET SKY1646-381LF: 2.2 to 2.8 GHz Two-Way, Degrees Power Divider Applications TD-LTE systems Satellite communications 2.4 GHz ISM band PORT1 Features Low insertion loss:.3 db @ 2.5 GHz High isolation:
More informationAdvantages of UltraCMOS DSAs with Serial-Addressability
0 Carroll Park Drive San Diego, CA, USA AN Tel: --00 Fax: -- www.psemi.com Advantages of UltraCMOS DSAs with Serial-Addressability Introduction Today s RF systems are more complex than ever as designers
More informationSMP LF: Surface-Mount PIN Diode for Switch and Attenuator Applications
DATA SHEET SMP32-085LF: Surface-Mount PIN Diode for Switch and Attenuator Applications Applications Low-loss, high-power switches Low-distortion attenuators (Pin 3) (Pin ) Features Low thermal resistance:
More informationOptimizing the Phase Accuracy of the PE44820 Phase Shifter
9380 Carroll Park Drive San Diego, CA 92121, USA AN45 Tel: 858-731-9400 Fax: 858-731-9499 www.psemi.com Optimizing the Phase Accuracy of the PE44820 Phase Shifter Introduction The PE44820 8-bit RF digital
More informationRFX8053: CMOS 5 GHz WLAN ac RFeIC with PA, LNA, and SPDT
DATA SHEET RFX8053: CMOS 5 GHz WLAN 802.11ac RFeIC with PA, LNA, and SPDT Applications 802.11a/n/ac WiFi devices Smartphones Tablets/MIDs Gaming Consumer electronics Notebooks/netbooks/ultrabooks Mobile/portable
More informationSKY LF: 0.1 to 3.8 GHz SP8T Antenna Switch
DATA SHEET SKY13418-485LF: 0.1 to 3.8 GHz SP8T Antenna Switch Applications Any 2G/3G/4G antenna diversity or LTE (TDD/FDD) transmit/receive system for which GSM transmit is not required Features Broadband
More informationHigh Isolation, Silicon SPDT, Nonreflective Switch, 0.1 GHz to 6.0 GHz HMC8038W
5 6 7 8 6 5 4 3 FEATURES Nonreflective, 50 Ω design High isolation: 60 db typical Low insertion loss: 0.8 db typical High power handling 34 dbm through path 29 dbm terminated path High linearity P0.dB:
More informationAS LF: PHEMT GaAs IC 1 W Low-Loss 0.1 to 6 GHz SPDT Switch
DATA SHEET AS225-313LF: PHEMT GaAs IC 1 W Low-Loss 0.1 to 6 GHz SPDT Switch Applications INPUT WLAN 802.11a/b/g Features OUTPUT1 OUTPUT2 Positive low voltage control (0/3 V) Low insertion loss (0.6, 0.1
More informationSKY LF: 0.1 to 3.0 GHz SP8T Antenna Switch
DATA SHEET SKY13418-485LF: 0.1 to 3.0 GHz SP8T Antenna Switch Applications Any 2G/3G/4G antenna diversity or LTE (TDD/FDD) transmit/receive system for which GSM transmit is not required Features Broadband
More informationSP4T RF Switch HSWA4-63DR+
MMIC SP4T RF Switch Absorptive RF Switch with internal driver Single Supply Voltage, +2.3V to +5.5V The Big Deal High Isolation, 61 @ 0.9 GHz Low insertion loss, 0.9 at 0.9 GHz High IP3, +58 m Fast switching,
More informationNCN Differential Channel 1:2 Mux/Demux Switch for PCI Express Gen3
4-Differential Channel 1:2 Mux/Demux Switch for PCI Express Gen3 The NCN3411 is a 4 Channel differential SPDT switch designed to route PCI Express Gen3 signals. When used in a PCI Express application,
More informationSKY LF: 0.1 to 3.8 GHz SP6T Antenna Switch
DATA SHEET SKY13416-485LF: 0.1 to 3.8 GHz SP6T Antenna Switch Applications Any 2G/3G/4G antenna diversity or LTE (TDD/FDD) transmit/receive system for which GSM transmit is not required Features Broadband
More informationSKY LF: 20 MHz to 6.0 GHz GaAs SPDT Switch
DATA SHEET SKY13351-378LF: 2 MHz to 6. GHz GaAs SPDT Switch Applications WLAN 82.11 a/b/g/n networks WLAN repeaters INPUT ISM band radios Low power transmit receive systems OUTPUT1 OUTPUT2 Features Positive
More informationSKY LF: 0.5 to 6.0 GHz SPDT Switch, 50 Ω Terminated
DATA SHEET SKY13348-374LF:.5 to 6. GHz SPDT Switch, 5 Ω Terminated Applications WiMAX 82.16 WLAN 82.11 a/b/g/n J1 J2 Features 5 Ω terminated RF outputs from.5 to 6. GHz Low insertion loss:.6 @ 2.5 GHz
More informationEND OF LIFE. Product Specification PE64908 RF- RF+ CMOS Control Driver and ESD. Product Description
Product Description PE64908 is a DuNE technology-enhanced Digitally Tunable Capacitor (DTC) based on Peregrine s UltraCMOS technology.this highly versatile product supports a wide variety of tuning circuit
More informationSKY LF: 0.5 to 6.0 GHz, 150 W High Power Silicon PIN Diode SPST Switch
DATA SHEET SKY12213-478LF: 0.5 to 6.0 GHz, 150 W High Power Silicon PIN Diode SPST Switch Applications Failsafe switching in TD-SCDMA, WiMAX, and LTE TDD base stations On/off switching in land mobile radios
More informationSKY , SKY LF: SP3T Switch for Bluetooth and b, g
DATA SHEET SKY325-349, SKY325-349LF: SP3T Switch for Bluetooth and 82.b, g Applications 82.b, g Bluetooth Zigbee TDMA/GSM/EDGE CDMA/WCDMA Other short-range wireless applications Simplified Block Diagram
More informationSKYA21012: 20 MHz to 6.0 GHz GaAs SPDT Switch
DATA SHEET SKYA2112: 2 MHz to 6. GHz GaAs SPDT Switch Automotive Applications Infotainment Automated toll systems Garage door opener 82.11 b/g/n WLAN, Bluetooth systems Wireless control systems Outdoor
More informationSKY LF: 0.05 to 2.70 GHz 40 W High Power Silicon PIN Diode SPDT Switch
DATA SHEET SKY12211-478LF:.5 to 4 W High Power Silicon PIN Diode SPDT Switch Applications Transmit/receive switching and RF path switching in TD- SCDMA, WiMAX, and LTE base stations Transmit/receive and
More informationRFX8425: 2.4 GHz CMOS WLAN/Bluetooth Dual-Mode RFeIC with PA, LNA, and SP3T
DATA SHEET RFX8425: 2.4 GHz CMOS WLAN/Bluetooth Dual-Mode RFeIC with PA, LNA, and SP3T Applications Smartphones, feature phones. and MIDs with WLAN/Bluetooth WLAN/Bluetooth platforms requiring shared antenna
More informationRFSW1012SR. Broadband SPDT Switch. Product Overview. Key Features. Functional Block Diagram. Ordering Information
Product Overview The is a single-pole double-throw (SPDT) switch designed for applications requiring very low insertion loss and high power handling capability. The excellent linearity performance of the
More informationDigital Step Attenuator
Surface Mount Digital Step Attenuator 75Ω 0 to 31, 1.0 Step 1MHz to 2.5 GHz DAT-3175A Series The Big Deal Wideband, operates up to 2.5 GHz Glitchless attenuation transitions High IP3, 52 m CASE STYLE:
More informationSKY LF: 0.9 to 4.0 GHz, 125 W High-Power Silicon PIN Diode SPDT Switch
DATA SHEET SKY12215-478LF: 0.9 to 4.0 GHz, 125 W High-Power Silicon PIN Diode SPDT Switch Applications Transmit/receive switching and failsafe switching in TD-SCDMA, WiMAX, and LTE base stations Transmit/receive
More informationABSOLUTE MAXIMUM RATINGS
Datasheet High Reliability SP2T RF Switch GENERAL DESCRIPTION The F2933 is a high reliability, low insertion loss, 5 Ω SP2T absorptive RF switch designed for a multitude of wireless and other RF applications.
More informationPreliminary Datasheet
Product Description The is a reflective SPDT RF switch that can be used in high power and good performance WLAN 802.11 a/b/g/n/ac/ax, DOCSIS 3.0/3.1 and Wireless Communication applications. This device
More informationPreliminary Datasheet
Product Description The is a reflective SPDT RF switch that can be used in high power and good performance WLAN 802.11 a/b/g/n/ac/ax, DOCSIS 3.0/3.1 and Wireless Communication applications. This device
More informationRFX8050: CMOS 5 GHz WLAN ac RFeIC with PA, LNA, and SPDT
DATA SHEET RFX8050: CMOS 5 GHz WLAN 802.11ac RFeIC with PA, LNA, and SPDT Applications 802.11a/n/ac Smartphones LEN RXEN ANT Tablets/MIDs Gaming Notebook/netbook/ultrabooks Mobile/portable devices RX Consumer
More informationNonreflective, Silicon SP4T Switch, 0.1 GHz to 6.0 GHz HMC7992
Nonreflective, Silicon SP4T Switch,.1 GHz to 6. GHz FEATURES Nonreflective, 5 Ω design High isolation: 45 db typical at 2 GHz Low insertion loss:.6 db at 2 GHz High power handling 33 dbm through path 27
More information10W Avg Broadband SPDT
10W Avg Broadband SPDT FEATURES Low insertion loss o 0.35dB @ 800MHz High isolation o 45dB @ 800MHz High Peak Power Handling No external DC blocking capacitors on RF lines 40dBm CW hot switching capable
More informationSKY LF: GHz 40 W High Power Silicon PIN Diode SPDT Switch
DATA SHEET SKY12209-478LF: 0.9-4.0 GHz 40 W High Power Silicon PIN Diode SPDT Switch Applications Transmit/receive switching and RF path switching in TD-SCDMA, WiMAX, and LTE base stations Transmit/receive
More informationF2932NBGP8. F2932 Datasheet GENERAL DESCRIPTION FEATURES COMPETITIVE ADVANTAGE FUNCTIONAL BLOCK DIAGRAM APPLICATIONS ORDERING INFORMATION * 2 GHZ
Datasheet High Reliability SP2T RF Switch GENERAL DESCRIPTION The F2932 is a high reliability, low insertion loss, 5 Ω SP2T absorptive RF switch designed for a multitude of wireless and other RF applications.
More informationCLA LF: Surface Mount Limiter Diode
DATA SHEET CLA4609-086LF: Surface Mount Limiter Diode Applications Low loss, high power limiters Receiver protectors Features Low thermal resistance: 25 C/W Typical threshold level: +36 dbm Low capacitance:
More informationSKY LF: 0.5 to 6.0 GHz SPDT Switch, 50 Ω Terminated
DATA SHEET SKY13348-374LF:.5 to 6. GHz SPDT Switch, 5 Ω Terminated Applications WiMAX 82.16 WLAN 82.11 a/b/g/n J1 J2 Features 5 Ω terminated RF outputs from.5 to 6. GHz Low insertion loss:.6 @ 2.5 GHz
More informationF2915NBGK8. F2915 Datasheet K Z GENERAL DESCRIPTION FEATURES FUNCTIONAL BLOCK DIAGRAM COMPETITIVE ADVANTAGE APPLICATIONS ORDERING INFORMATION
Datasheet High Reliability SP5T RF Switch GENERAL DESCRIPTION The F2915 is a high reliability, low insertion loss, 5 Ω SP5T absorptive RF switch designed for a multitude of RF applications including wireless
More information