Connection targets. Universal sensors and switches, universal output devices

Transcription

1 AnyWireASLK System Products Guide ASLKTERMAL [ASLK Small Terminal Block Terminal] BL296 B-08F EURO block type The Products Guide describes individual products. Refer to the Guide as necessary. Function List Model Specifications Connection targets Functions ASLKTERMAL four-wire (isolated) NPN 8-point input/8-point output PNP 8-point input/8-point output NPN 4-point input/4-point output (hybrid) PNP 4-point input/4-point output (hybrid) Universal sensors and switches, universal output devices Slave unit voltage reduction Sensing level reduction I/O disconnection I/O short circuit I/O reduction Smallsized Notes on use To set any address, an Address writer ARW-04 (Ver or higher), ARW-03 (Ver or higher) is required. Please prepare it separately. [Notes on Safety] Precautions that must be observed in order to use this system safely are indicated as shown below. You must observe these precautions. WARNG A WARNG indicates a potentially hazardous situation which, if not handled correctly, could result in death or serious injury. A indicates a potentially hazardous situation which, if not handled correctly, may result in personal injury or property damage. WARNG System Safety This system is intended for general industrial applications. It does not have functions for supporting applications requiring higher levels of safety such as safety-related devices or accident prevention systems. The product must not be used for these purposes. Always turn off the power before attempting to mount or replace. Prolonged continuous flow of a rated load current or higher or a transit current due to load short-circuit, etc., in the hybrid unit including the output unit and the output circuit may result in smoking or firing. An external safety device such as a fuse must be installed. System Use a stable, DC. Use of an unstable may cause problems with the system. Separately route high-voltage and power cables Although the AnyWireASLK has a high noise margin, keep the transmission line and I/O cables away from high-voltage and power cables. Connectors and s Pay careful attention to the length and installation of cable wiring to ensure that connectors and cables are neither overloaded nor disconnected. Make sure to prevent any metal objects from getting inside the connectors or the blocks. Short-circuits caused by metal objects or mis-wiring are likely to damage the device. Do not impose any external loads on the units. Doing so may cause a failure. Do not disconnect or reconnect between the transmission line and slave units. A malfunction may occur. Use the AnyWireASLK within the range of the specifications and conditions shown below. [Warranty] Warranty period The warranty on the delivered Product shall continue to be effective for one (1) year after the delivery thereof to a location as designated by the original owner. Scope of warranty Should a defect occur in any part of the Product during the foregoing warranty period when it is used normally in acordance with the specifications described in this User's Manual, the Company shall replace or repair the defect free of charge, except when it arises as a result of: [1] Misuse or abuse of the Product by the owner; [2] Fault caused by other than the delivered Product; [3] The unauthorized modification or repair of the Product by any person other than the Company's personnel; [4] Any unusual force of nature, disaster or other cause beyond the Company's control. The term "warranty," as used herein, refers to the warranty applicable to the delivered product alone. The Company shall not be liable for consequential or incidental damages resulting from any malfunction. Repair at cost After the expiration of the warranty period, the owner shall be responsible for all costs and expenses incurred for the troubleshooting and repair of the Product. Even during the warranty term, the Company shall repair any defects arising from causes other than within the scope of the warranty as specified above, at the owner's cost. -BL296*B08F**** 1/22-

2 [AnyWireASLK Terminal] The AnyWireASLK can employ a two-wire or four-wire selectively depending on the load current. This Products Guide describes a four-wire (isolated). If the load current is small, using a two-wire (non-isolated) allows for achieving simplified wiring without local. In the case of prioritizing the sites of concentrated loads and/or the number of connections, hybridization with a four-wire (isolated), which supports local, is also possible. Make sure to use a four-wire (isolated) in the case of input and load driving using an external. In the case of hybridization, refer to the Two-Wire (Non-Isolated) Terminal Products Guide separately. [Connection Example] AnyWireASLK master General-purpose filter Red: Black: ASLK filter Red: Black: Two points Relationship between the size and length of the transmission line and the supply current (Table 1) Size of the transmission line (, ) 1.25mm mm 2 0.5mm 2 Supply current on the transmission line (, ) Total length 50m or less Total length 50m to 100m Total length 100m to 200m MAX 2A MAX 1A MAX 0.5A MAX 1.2A MAX 0.6A MAX 0.3A MAX 0.8A MAX 0.4A MAX 0.2A DC* * Make sure to use a DC stabilized for the to be connected. * When complying with the UL Standard, make sure to use a DC stabilized of NEC Class 2 Output. Dedicated flat cable 1.25mm 2 (four-wire) 4P link connector is convenient for branching. Red: Two points Black: Two points Two points If the load consumption current is large, a four-wire (isolated) can be selected. This can correspond to I/O of the controller with an external. 8 points Red: Black: 8 points - Refer to Table 1 so that the size and length of the transmission line and the allowable supply current lie within an appropriate range. - Connect the same symbols (, ) correctly between the AnyWireASLK master and each device. - The branching length or branch number has no limitation. - Include the length of the cable provided with the in the total line length. - Connect the terminator BT0 (polar) to the, farthest from AnyWireASLK master. The sum of the portions of, is the total line length. General-purpose filter Black: DC* The branching has no limitation. Two points Red: Two points Black: Two points Red: Two points Red: Black: Two points BT0 AnyWireASLK terminator One terminator should be connected to the, farthest from the AnyWireASLK master. Connect it correctly so as not to set the wrong polarity. [Installation Location] -Location where the unit is not subject to vibration or shock -Location where the unit is not directly exposed to dust -Location where the main body is not directly exposed to conductors such as waste metal and sputter -Location where humidity is not condensed -Location where the atmosphere is free of corrosive gas, flammable gas and sulfur -Location where the unit is removed from high-voltage or high-current cables -Location where the unit is removed from cables and controllers that generate servo, inverter or other high-frequency noise. -BL296*B08F**** 2/22-

3 ~ [Precautions for use with 4-Wire (Insulated) Terminal] If any of the side-by-side lines of,, and exceeds the total length of 50m in a system to be supplied, serially connect the ASLK filter [Type ANF-01] or filter of COSEL Co., Ltd. [Type EAC ] to and in the starting position of the side-by-side lines. This will improve noise resistance, reduce the impact of crosstalk by transmission signals and stabilize the signals. In any case of to the entire system from the master driving or from the local, insert a filter. Insert the ASLK filter [Type ANF-01] regardless of installation method and distance when complying with CE Standard. Filter allowable power current Model Type Allowable power current ASLK filter ANF-01 MAX 5A/ DC Filter of COSEL Co., Ltd. EAC MAX 6A/ DC AnyWire Type: ANF-01 Connection example 1Power supply to the entire system AnyWireASLK master 2-wire LG General-purpose power supply filter (Use it if necessary.) POWER SLAVE PE ANF-01 If any of the side-by-side lines of,, and exceeds the total length of 50m BT0 FG N L DC stabilized ~ 2Local /branching 2-wire 2-wire AnyWireASLK master FG N L LG DC stabilized POWER General-purpose power supply filter (Use it if necessary.) SLAVE PE ANF-01 If any of the side-by-side lines of,, and exceeds the total length of 50m POWER SLAVE L N FG PE ANF-01 DC stabilized General-purpose power supply filter (Use it if necessary.) A BT0 ~ B If (A+B) of the side-by-side lines of,, and exceeds the total length of 50m -BL296*B08F**** 3/22-

4 ~ COSEL Co., Ltd. Type: EAC Connection example 1Power supply to the entire system AnyWireASLK master * When using this filter, please be careful of the positions of LOAD and LE. 2-wire LG General-purpose filter (Use it if necessary.) LOAD LE PE EAC * If any of the side-by-side lines of,, and exceeds the total length of 50m BT0 FG N L DC stabilized ~ 2Local /branching * When using this filter, please be careful of the positions of LOAD and LE. 2-wire 2-wire AnyWireASLK master FG N L LG General-purpose filter (Use it if necessary.) DC stabilized LOAD LE PE EAC * If any of the side-by-side lines of,, and exceeds the total length of 50m L N FG DC stabilized LOAD LE PE EAC * General-purpose power supply filter (Use it if necessary.) A BT0 ~ B If (A+B) of the side-by-side lines of,, and exceeds the total length of 50m -BL296*B08F**** 4/22-

5 [Type] NPN PNP Terminal BL296SB-08F BL296XB-08F BL296PB-08F 8-point input 4-point input,4-point output 8-point output BL296SB-08FS BL296XB-08FS BL296PB-08FS 8-point input 4-point input,4-point output 8-point output Standard block M3, 7.62mm pitch Width 6mm, Y, round BL296SB-08F-3 BL296XB-08F-3 BL296PB-08F-3 8-point input 4-point input,4-point output 8-point output BL296SB-08FS-3 BL296XB-08FS-3 BL296PB-08FS-3 8-point input 4-point input,4-point output 8-point output Spring block 5.08mm pitch Twisted wire, ferrule BL296SB-08F-11 BL296XB-08F-11 BL296PB-08F-11 8-point input 4-point input,4-point output 8-point output BL296SB-08FS-11 BL296XB-08FS-11 BL296PB-08FS-11 8-point input 4-point input,4-point output 8-point output EURO block 5.08mm pitch Twisted wire, ferrule [Name of each part] ALM LK Standard block Cover mounting hole Infrared port Input/output display Mounting hole ALM Infrared port LK Input/output display Spring block Cover mounting hole Mounting hole ALM Infrared port LK Input/output display EURO block Cover mounting hole Mounting hole -BL296*B08F**** 5/22-

6 [Terminal Layout (Standard Terminal Block) (NPN)] (Input) BL296SB-08F : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296SB-08F-V50 or install for the common externally. (Output) BL296PB-08F : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A (Mixed) BL296XB-08F : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296XB-08F-V50 or install for the common externally. Input output BL296*B08F**** 6/22-

7 [Terminal Layout (Standard Terminal Block) (PNP)] (Input) BL296SB-08FS : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296SB-08FS-V50 or install for the common externally. (Output) BL296PB-08FS : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A (Mixed) BL296XB-08FS : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296XB-08FS-V50 or install for the common externally. Input output BL296*B08F**** 7/22-

8 [Terminal Layout (EURO Terminal Block) (NPN)] (Input) BL296SB-08F-3 : transmission line (+) : transmission line (-) : for, : for, (Output) BL296PB-08F The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296SB-08F-3-V50 or install for the common externally. : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A (Mixed) BL296XB-08F-3 : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296XB-08F-3-V50 or install for the common externally. Input output BL296*B08F**** 8/22-

9 [Terminal Layout (Spring Terminal Block) (PNP)] (Input) BL296SB-08FS-3 : transmission line (+) : transmission line (-) : for, : for, (Output) BL296PB-08FS The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296SB-08FS-3-V50 or install for the common externally. : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A (Mixed) BL296XB-08FS-3 : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296XB-08FS-3-V50 or install for the common externally. Input output BL296*B08F**** 9/22-

10 [Terminal Layout (EURO Terminal Block) (NPN)] (Input) BL296SB-08F-11 : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296SB-08F-11-V50 or install for the common externally. (Output) BL296PB-08F-11 : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A (Mixed) BL296XB-08F-11 : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296XB-08F-11-V50 or install for the common externally. Input output BL296*B08F**** 10/22-

11 [Terminal Layout (EURO Terminal Block) (PNP)] (Input) BL296SB-08FS-11 : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296SB-08FS-11-V50 or install for the common externally. (Output) BL296PB-08FS-11 : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A (Mixed) BL296XB-08FS : transmission line (+) : transmission line (-) : for, : for, The total passing current of : maximum 0.8A For a three-wire sensor, please select BL296XB-08FS-11-V50 or install for the common externally. Input output BL296*B08F**** 11/22-

12 [Input/Output Circuit Configuration and Electrical Properties] (insulated) NPN input BL296SB-08F <Circuit conditions> Rated input voltage : DC Maximum switching current : 3.5mA ON current : 2.2mA or more OFF current : 1mA or less ON voltage OFF voltage : (-) 16V or more : (-) 8V or less 6.8k Switch, sensor, etc. (2-wire type) In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. [Ex.] Use with the common value set at. 6.8k (insulated) ASLK (AnyWire series ) Control circuit Load by external type (insulated) NPN output BL296PB-08F <Circuit conditions> Withstand voltage : 3 DC Maximum ON current : 100mA Load In the case of an inductive load, mount a surge killer. If the power is turned on with the circuit between and shorted, passive elements will be damaged. In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. [Ex.] Use with the common value set at. (insulated) ASLK (AnyWire series ) Control circuit Load by external type -BL296*B08F**** 12/22-

13 [Input/Output Circuit Configuration and Electrical Properties] (insulated) NPN BL296XB-08F (Input side) <Circuit conditions> Rated input voltage : DC Maximum switching current : 3.5mA ON current : 2.2mA or more OFF current : 1mA or less ON voltage : (-) 16V or more OFF voltage : (-) 8V or less 6.8k Switch, sensor, etc. (2-wire type) In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. [Ex.] Use with the common value set at. 6.8k (insulated) ASLK (AnyWire series ) Control circuit Load by external type (insulated) NPN BL296XB-08F (Output side) <Circuit conditions> Withstand voltage : 3 DC Maximum ON current : 100mA In the case of an inductive load, mount a surge killer. Load If the power is turned on with the circuit between and shorted, passive elements will be damaged. In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. Control circuit [Ex.] Use with the common value set at. (insulated) ASLK (AnyWire series ) Load by external type -BL296*B08F**** 13/22-

14 [Input/Output Circuit Configuration and Electrical Properties] (insulated) PNP input BL296SB-08FS <Circuit conditions> Rated input voltage : DC Maximum switching current : 3.5mA ON current : 2.2mA or more OFF current : 1mA or less ON voltage : (-) 16V or more OFF voltage : (-) 8V or less 6.8k Switch, sensor, etc. (2-wire type) In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. [Ex.] Use with the common value set at. 6.8k (insulated) ASLK (AnyWire series ) Control circuit Load by external type (insulated) PNP output BL296PB-08FS <Circuit conditions> Withstand voltage : 3 DC Maximum ON current : 100mA Load In the case of an inductive load, mount a surge killer. If the power is turned on with the circuit between and shorted, passive elements will be damaged. In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. [Ex.] Use with the common value set at. (insulated) ASLK (AnyWire series ) Control circuit Load by external type -BL296*B08F**** 14/22-

15 [Input/Output Circuit Configuration and Electrical Properties] (insulated) PNP BL296XB-08FS (Input side) <Circuit conditions> Rated input voltage : DC Maximum switching current : 3.5mA ON current : 2.2mA or more OFF current : 1mA or less ON voltage : (-) 16V or more OFF voltage : (-) 8V or less 6.8k Switch, sensor, etc. (2-wire type) In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. [Ex.] Use with the common value set at. 6.8k (insulated) ASLK (AnyWire series ) Control circuit Load by external type (insulated) PNP BL296XB-08FS (Output side) <Circuit conditions> Withstand voltage : 3 DC Maximum ON current : 100mA (9 to 12) Load (3, 4) In the case of an inductive load, mount a surge killer. If the power is turned on with the circuit between and shorted, passive elements will be damaged. In the case of connecting with a load (input/output port, etc.) controlled by a different from the power supply used with AnyWireASLK, make sure to use a (insulated). Otherwise a malfunction may occur. (9 to 12) (3, 4) Control circuit [Ex.] Use with the common value set at. (insulated) ASLK (AnyWire series ) Load by external type -BL296*B08F**** 15/22-

16 [Address Number Setting] 1Address number writing - The address number to be set to the is for correspondence to the input/output memory map of the controller. The address number represents an assignment position for AnyWire transmission frames (0 to 254) and occupies 8 points following the number (and is not a station number). - The address number can be set by one point. - Use a dedicated address writer ARW-04 (Ver.04 to 1.01 or higher) or ARW-03 (Ver or higher) to write the address to be set in the. Refer to the User s Manual separately to learn how to operate the address writers ARW-04 (Ver.04 to 1.01 or higher) and ARW-03 (Ver.2.10 or higher). 1 Connect the AnyWire master to the transmission line of BL296 B-08F and supply a transmission signal. 2 Operate the ARW-04 (Ver or higher) and ARW-03 (Ver.2.10 or higher) to write the address numbers. Address numbers settable with BL296 B-08F : 0 to Disconnect the BL296 B-08F from the master. Setting image when setting with ARW-04 (Ver or higher), ARW-03 (Ver2.10 or higher) Direct the address writer toward the setting port (Fig. 1) of the body. Fig. 1 Setting port BL296SB-08F BL296XB-08F BL296PB-08F (Input side) (Output side) Transmission signal AnyWireASLK master DC* Red: Black: BL296SB-08FS BL296XB-08FS (Input side) (Output side) BL296PB-08FS Avoid a short-circuit of the above lines during supply of power. A malfunction may result. * Make sure to use a DC stabilized for the to be connected. The factory setting of the is 255, which means no setting. In this state, the cannot perform an input/output operation. An address auto-recognition (refer to the Manual of the master unit) cannot register the unit ID. Upon use, make sure to set the address numbers within the range of 0 to Settings reading Refer to the User s Manual separately to learn how to operate the address writers ARW-04 (Ver or higher) and ARW-03 (Ver.2.10 or higher). [Power Consumption] Type BL296SB-08F BL296XB-08F BL296PB-08F BL296SB-08FS BL296XB-08FS BL296PB-08FS Power Consumption -: 6mA side: Sum of 40mA and three-wire sensor control current *1 - side: 6mA side: (Input) Sum of 20mA and three-wire sensor control current *1 and (Output) Sum of 6mA and load current *2 - side: 6mA side: Sum of 10mA and load current *2 -: 6mA side: Sum of 40mA and three-wire sensor control current *1 - side: 6mA side: (Input) Sum of 26mA and three-wire sensor control current *1 and (Output) Sum of 6mA and load current *2 - side: 6mA side: Sum of 10mA and load current *2 *1 All points are short-circuited between and for NPN and between and for PNP. If a three-wire sensor is connected, add power consumption by the sensor. *2 All points are turned ON with no load connected. Add power consumption by the load for the capacity. -BL296*B08F**** 16/22-

17 [Indication Function] Normal state: LK flashing, ALM off, I/O ON on/off off Example of BL296 B-08F LED indication LED symbol LK ALM LK ALM Indication status On Flashing Off On Flashing Off Alternate flashing LK ALM No transmission wave Normal Detailed states, disconnected or no I/O voltage reduced Transmission signal level reduced Normal Master unit detecting the unit ID (address) redundant or not set LK ALM I/O 0 I/O 1 I/O 2 I/O 3 I/O 4 I/O 5 I/O 6 I/O 7 I/O On Off ON OFF For information on narrowing down the cause of a trouble occurrence, see the following section Troubleshooting. In case of an abnormal indication status, narrow down the cause and remove the trouble based on the on/flashing status and the left table. The indication status will be restored automatically after the trouble is removed. [Troubleshooting] <LK not flashing> Check items Check the connection status of the slave unit. Check the connection status of the master unit. Measures Disconnect and reconnect the slave unit. Check if the LK LED of the master unit flashes and take the following measures. 1) If the LK of the master unit flashes and the LK of the slave unit is on, the master unit may be damaged. Please contact our helpdesk. 2) If the LK of the master unit flashes and the LK of the slave unit is off, the master unit may not be powered ( DC), the transmission line (, ) may be partially disconnected, or the slave unit may be damaged. Check if the master unit is powered and, if necessary, please contact our helpdesk. 3) If the LK of the master unit does not flash, check if the master unit is powered. Other system errors may also occur. Refer to the User s Manual of the master unit. <ALM on> Check items Measures Check the I/O side connection of the slave unit. <ALM flashing> Check items Check the voltage of the external ( DC) of the master unit. Please adjust the voltage of the external power source to within the rated value of 21.6V to 27.6V. Also, with the wiring for s, please ensure that transmission lines are not touching or misfired. Measures Adjust the voltage of the external of the master unit to lie within the range from 21.6 to 27.6V (recommended voltage is 26.4V). Check the total line length. Review the total line length and the size of the transmission line so as not to connect a load exceeding a supply current limit on the transmission line and, if necessary, adjust the connected load (e.g. the supply current on the transmission line is 2A if the size is 1.25mm 2 and the total length is 50m or less). <LK and ALM flashing alternately> Check items Measures Check the address of the slave unit. The address of the slave unit is not set (255) or address redundancy occurs. Take the following measures. 1) Change the address within the range from 0 to ) Check if there is another slave unit undergoing the same flashing and, if necessary, reset the address so as not to be redundant. -BL296*B08F**** 17/22-

18 [Specifications] General Specifications Ambient temperature use Ambient humidity use Temperature/humidity storage Atmosphere Altitude use *1 Pollution level *2 Noise resistance *1 Do not use or store AnyWireASLK equipment under an environment pressurized higher than the atmospheric pressure at an altitude of 0m. Otherwise, a malfunction may occur. *2 This is an index that shows the occurrence level of conductive substances in the environment where the equipment is used. In the case of pollution level 2, only non-conductive pollution occurs. However, this is an environment where temporary conductivity can occur by accidental condensation. Transmission Specifications Power supply voltage use Transmission method Synchronization method Transmission procedure Connection mode Number of connection points Number of connection points %RH No condensation No corrosive gas m 2 or less 120p-p (pulse width 1μs) DC +15% to -10% (21.6 to 27.6V DC) with a ripple of 0.5Vp-p or less DC superimposed total frame/cyclic method Frame/bit synchronization method Dedicated protocol Bus type (multi-drop method, T-branch method, tree method) 512 max. (: 256, : 256) Up to 128 units Individual Specifications Number of occupied data items Response time* 3 Monitoring function Mass BL296 B-08F BL296 B-08FS BL296 B-08F-3 BL296 B-08FS-3 BL296 B-08F-11 BL296 B-08FS-11 Max. 1ms Slave unit voltage reduction I/O voltage reduction BL296 B-08F :75g BL296 B-08FS :75g BL296 B-08F-3 :70g BL296 B-08FS-3 :70g BL296 B-08F-11 :65g BL296 B-08FS-11 :65g NPN Input 8 point PNP Input 8 point NPN Input 4 point, Output 4 point PNP Input 4 point, Output 4 point NPN Output 8 point PNP Output 8 point *3 Apart from the transmission delay time (2 cycle time), this is internal processing time required for the to recognize signal changes. -BL296*B08F**** 18/22-

19 [Outside dimensions] Unit: mm BL296 B-08F (49)* * Terminal block cover opening status (0.69) (0.69) Ø Supports M3, 7.62mm pitch, width 6mm, crimping s -BL296*B08F**** 19/22-

20 [Outside dimensions] Unit: mm BL296 B-08F (1.47) (1.47) Ø * The figure shows an example of layout for NPN 8-point output. Spring type Euro block Core diameter of connecting electric wire: 0.08 to 2.5mm 2 Length of stripped electric wire: 5 to 6mm When connecting two wires to one, bind the wires with a twin ferrule (crimp clamp) and insert it in the. -BL296*B08F**** 20/22-

21 [Outside dimensions] Unit: mm BL296 B-08F Ø (0.18) (0.75) * The figure shows an example of layout for NPN 8-point output. Length of stripped wire : 6mm Connecting wire: twisted wire : 0.14 to 1.5mm 2 When crimping bar with sleeve : 1mm 2 When crimping 2-wire bar with sleeve : 0.5mm 2 -BL296*B08F**** 21/22-

22 [Outside dimensions] Unit: mm A-108 (installation dedicated D rail adapter) dimensions Ø3.5 (Mounting screw hole) [Address] Anywire Corporation Headquarters :1 Babazusho, Nagaokakyo-shi, Kyoto JAPAN Contact :Contact by mail :Contact by website info_e@anywire.jp Printed in Japan 2014,2015,2016,2017 UMA-10316H-EN -BL296*B08F**** 22/22-