BossDim RS. User manual - UK
|
|
- Lewis Kelly
- 5 years ago
- Views:
Transcription
1 BossDim RS User manual - UK
2 Congratulations on acquiring your new BossDim RS We are happy you have chosen our product to control your home lighting, and we hope it gives you hours of pleasure. On the following pages you can read all you need to know about using your BossDim RS, which can either be operated at the touch of a finger or from a B&O remote control, which can be programmed to remember as many as 9 different light scenarios. Connection The product should be connected straight to a 230V supply, and the light source connected to the outlet. The BossDim RS has connections for wires on both sides so that the wires of both can be led out on the same side or one on each side when fitting to ceiling mounted lamps.
3 Z-wave The BossDim RS has a built-in radio transmitter and receiver. The Z-Wave protocol is used to communicate with other INNOVUS units. The range is approx 30 meters. All non battery-operated INNOVUS units act as repeaters which can re-transmit radio signals if there is a need for distances in excess of 30 meters. A control unit is needed to use the B o s s D i m R S in a Z-Wave network, such as e.g. INNOVUS Smoothremote, INNOVUS Smartswitch or INNOVUS House controller. Consult the instructions for use for the control unit for more information. When you are requested to activate the unit, in this case the BossDim RS, which is to be registered in the Z-Wave network, the BossDim RS will be temporarily affected. Then the control unit will indicate that the new unit has been registered in the Z-Wave network. Note that the BossDim RS and the control unit must be located within 2 meters of each other when the BossDim RS registered in/deregistered from the Z-Wave network. When the BossDim RS is connected to the Z-Wave network it cannot be used immedi - ately. You must first tell the control unit which button you wish to assign to your new BossDim RS. As part of the same process you will be asked to activate the unit, which is done in the same way. Now you can operate your new BossDim RS dimmer in the same way as you operate it locally. Several units can be connected to the same group/button on the control unit.
4 Technical specifications Voltage V AC Max. wattage 200 Watt Load <1 Watt CPU ZW0201 Dimmer type Leading edge or Trailing edge (FET) Radio frequency 868 MHz Z-Wave device type Routing slave Size (diameter x depth) 85 x 27 mm Installation The unit is designed for indoor use - rating IP20 Operation IR Radio Local B&O compatible Z-Wave EU Finger touch Terminating blocks BossDim RS can be blocked against local operation. The system can be blocked at two levels: at level 1 blocks can be temporarily removed with 2 short touches; BossDim can then be oper - ated locally for 30 seconds before blocking is reactivated.
5 Connection 230V ordinary/halogen bulbs Electronic transformer/halogen bulbs Transformer/halogen bulbs Low-energy bulbs (On and Off only) Fluorescent tubes (On and Off only) CAUTION This product must be connected to 230V, and should be installed by a qualified electrician. Short circuiting of the output terminal may permanently damage the product.
6 Squeeze the outside with two fingers at the wire penetration points. Pull the rear cover up and out. Holes must be pierced for the wires to penetrate. If you wish to introduce both wires on the same side, pierce two holes in the desired side. If you wish to introduce the wires one on each side, pierce one hole on each side. If you wish to screw the BossDim RS on walls or ceilings, pierce four holes in the rear cover.
7 The protective cover can be removed after the screw has been removed. Introduce the exposed wires through holes pierced. Twist the wires around the strain relief. Connect the wire from the lamp to "OUT, blue wire to the outer terminal and the wire from the mains to "IN and blue wire to the outer terminal. Close the protective cover and screw down. Click on the rear lid The product contains electronic materials and should be delivered to an electronic waste recycling station for disposal Volt AC 50 HZ Max. 200 W D H H B K B
8 Operation The BossDim RS is fitted with a touch-sensitive stainless steel strip which is controlled by gentle touching. The BossDim RS can distinguish between a short touch of the hand and continuous touching. A brief touch of the BossDim RS will switch lights on and off. When the BossDim RS is switched on by a brief touch of the hand the light intensity will re - turned to the same level as when it was switched off. NB! If a BossDim RS is left switched off, after e.g. a power cut it will remain extinguished when the power is restored. In the same way, it will return to the same intensity if the BossDim RS was already switched on. A continuous touch to the BossDim RS will increase light intensity to 100% or untilyour hand is removed. To reduce light intensity, touch the BossDim RS briefly and then touch continuously. The light intensity will decrease to 10% or until your hand is removed. The BossDim RS has been designed with a sleep function so it can dim light intensity from the current level to off over 30 minutes. Briefly touch the BossDim RS twice to acti - vate this function. When the BossDim RS is switched on again by a brief touch of the hand, light intensity will return to the same intensity as before the function was activated. The BossDim RS can be operated as normal even when the sleep function is active, but this will deactivate the sleep function. Besides the touch-sensitive steel strip, the B o s s D i m R S is fitted with a red LED which flashes while the BossDim RS is altering light intensity.
9 B&O The BossDim RS can be operated from a B&O remote control. All units in the same room can be operated at one and the same time, or individual dimmers may be allocated a unique number (1-9). Light intensity can be increased or decreased or completely extinguished. Up to 9 different lighting scenarios can be set up in each room, e.g. for television, eating etc. The BossDim RS has 9 different programmable light intensities which can be selected from a B&O remote control. The manufacturer's default settings are as follows: Program no Intensity 20% 30% 40% 50% 60% 70% 80% 90% 100% If there is more than one BossDim RS or some other B&O dimmer in the same room, each dimmer can be assigned a number from 1 to 9 for individual control. The BossDim RS has no manufacturer's default number.
10 BEO4 Select program (All in same room) Press "Light" followed by the program number (1-9). Alter light intensity (all in same room) Press Light followed by the up/down arrow Switch off light (all in same room) Press Light followed by stop Altering light intensity (single lamp) Your BossDim RS must have already been assigned a number, see "Assigning dimmer numbers". Press Light Press "List" until "Lamp" appears on the display Select the number of the lamp you wish to alter the light intensity of Press up/down arrows to alter intensity Switch off light (single lamp) Your BossDim RS must have already been assigned a number, see "Assigning dimmer numbers". Select the number of the lamp you wish to alter the light intensity of Press Stop Save the current light setting in the room Press Light Press "List" until "Store" appears on the display Press "Go" followed by the number of the program (1-9) Press Go Now you can restore the current light setting by pressing "Light" followed by the program number. Assigning dimmer numbers The B o s s D i m R S must be switched on during the whole of this process. Do this by - con stantly touching the aluminium strip. Press Light Press List until Setup appears on the display Press Go Press List until Store appears on the display Press Go Press the desired number (1-9) Press Go Press Light Press "List" until "Lamp" appears on the display
KNX radio wall-transmitter 1gang/2gang flat quicklink Order no.: 8565 x2 xx
KNX radio wall-transmitter 1gang/2gang flat quicklink KNX radio wall-transmitter 1gang/2gang flat quicklink Order no.: 8565 x2 xx KNX radio wall-transmitter 1gang/2gang flat solar quicklink Order no.:
More informationFibaro System Modules
Chapter 3 Fibaro System Modules 3.1 Fibaro Dimmer FGD211 Figure 3.1: Dimmer module, FGD-211 Radio controlled light dimming module, designed to work with light sources of any type. May be connected to two-wire
More informationV~ DIMMER WITH BUILT-IN RADIO RECEIVER AND DALI OUTPUT FOR CONTROL BALLASTS AND LAMPS. Push-button input for manual controls.
MR RESISTOR 110-230V~ DIMMER WITH BUIT-I RADIO RECEIVER AD DAI PUT FOR CTRO BAASTS AD AMPS. Push-button input for manual controls. Product code TVDMA868A01 20 slaves, 868.3Mhz TVDMA868A02 64 slaves, 868.3Mhz
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationAPA3-1500R STARTER SET WIRELESS SWITCHING
COMPATIBILITY This set can be combined with all trust smart home transmitters and receivers. TECHNICAL SPECIFICATIONS RECEIVER Power supply input Maximum load RF frequency RF range Memory addresses 3 220-240
More informationImportant Safety Information
OWNER'S MANUAL Important Safety Information 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only
More informationRadio motion detector comfort 1.1 m/2.2 m quicklink Order number
Radio motion detector comfort 1.1 m/2.2 m quicklink Order number 8534 51.. Operating instructions 1. Safety instructions Electrical equipment may only be installed and assembled by a qualified electrician
More informationB-Tronic EasyControl EC5401B
B-Tronic EasyControl EC5401B en Assembly and Operating Instructions Wall/hand-held transmitter, 1-channel, bidirectional Important information for: Fitters / Electricians / Users Please forward accordingly!
More informationLK Wireless Room Control Cq
LK Wireless Room Control Cq Description LK Wireless Room Control Cq consists of a LK Room Thermostat Cq-n (transmitter) and a LK Receiver Unit Cq 8 (8 channel receiver unit). The range also includes a
More informationWireless Receiver E28Q Mounting and Operating Instructions (Original operating instructions)
EN Wireless Receiver E28Q Wireless Receiver E28Q Mounting and Operating Instructions (Original operating instructions) Always read before initial operation! 28509900_E28Q_EN_2012-05-08.doc 1 / 12 1 Data
More informationAT-SL-DDR & AT-SL-DDR-SA
AT-SL-DDR & AT-SL-DDR-SA Product Guide Slim-line RF DALI/DSI + relay controller Overview The AT-SL-DDR and AT-SL-DDR-SA are wireless controllers with two output channels capable of controlling incandescent,
More informationTABLE OF CONTENT A. Installation and Mounting Installation 3 2. Mounting Receiver Addressing... 5 B. Key Interface. 7 C.
TABLE OF CONTENT A. Installation and Mounting.. 3 1. Installation 3 2. Mounting.. 4 3. Receiver Addressing... 5 B. Key Interface. 7 C. LCD Interface...8 D. Start/Reset...9 E. Operation Mode.10 F. Time
More informationtough lightweight clever Instructions for use 300 &
tough lightweight clever Instructions for use 300 & 600 0845 618 2889 Congratulations! Welcome to our lightweight super tough elitepro2. The instructions in this manual apply to both our 300Ws and 600Ws
More informationAT-SL-DDR & AT-SL-DDR-SA
Product Guide AT-SL-DDR & AT-SL-DDR-SA Slim -line RF DALI/DSI + relay controller Overview The AT-SL-DDR andat-sl-ddr-sa are wireless controllers with two output channels capable of controlling incandescent,
More informationOperating instructions II / 2004
Operating instructions II / 2004 Light and presence sensor TOUCH DIM LS/PD LI OSRAM GmbH Costumer-Service-Center (CSC) Steinerne Furt 62 86167 Augsburg, Germany www.osram.com www.osram.de Tel. : (+49)
More informationBrunata Optuna H Ultrasonic energy meter Type 775 Installation Guide Edition 1.2
Ultrasonic energy meter Type 775 Installation Guide Edition 1.2 UK-QB101575 / 29.05.2012 Brunata a/s is a Danish owned company. We have more than 90 years of experience within developing and producing
More informationWireless Control Systems
Wireless Control Systems Leading the way in intelligent automation contents Range Overview Typical Installations Transmitters Combined Modules Receivers Accessories Programming Switching & Dimmer Functions
More informationSTC65 RS485 Modbus. EnOcean Receiver/Transmitter with RS485 Modbus Interface. Data Sheet. Application. Security Advice Caution.
STC65 RS485 Modbus EnOcean Receiver/Transmitter with RS485 Modbus Interface Data Sheet Subject to technical alteration Issue date: 27.06.2014 Application Bidirectional gateway for EnOcean-based sensors
More informationUser guide ProHead Plus
User guide ProHead Plus For other languages visit: /support ProHead Plus 2 Congratulations on your new Profoto product! Thanks for showing us your confidence by investing in a ProHead unit. For more than
More informationRadio controlled home automation
Radio controlled home automation for retro-fit and new projects Hager quicklink is a home automation system accessible to all installers. It's an easy to use radio operation, offering control of applications
More informationlighting your creativity HONEY BADGER 320Ws Digital Flash Instruction Manual
lighting your creativity HONEY BADGER 320Ws Digital Flash Instruction Manual www.interfitphotographic.com Honey Badger 320 Digital Flash What s cool about the Honey Badger? The Honey Badger is the perfect
More informationWIRELESS 868 MHz TEMPERATURE STATION Instruction Manual
WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this temperature station with wireless 868 MHz transmission of outdoor temperature and display of indoor
More informationQuik Bridge Two- Channel Receiver Document Number: Rev. C September 1999
Quik Bridge Two- Channel Receiver Document Number: 466-547 Rev. C September 999 97G07A.DSF 60-760 INSTALLATION INSTRUCTIONS Product Summary The Quik Bridge Two-Channel Receiver allows two zones of a hardwired
More informationControls. LCD display A B C D E F
H205 Version 1 1 2 3 4 5 6 13 12 11 7 8 9 10 14 15 17 18 16 1 19 Controls 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Carrying strap holder Preset 1 Preset 2 Preset 3/STEP button Preset 4 LCD display
More informationWIRELESS 868 MHz TEMPERATURE STATION Instruction Manual
WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this compact 868MHz Temperature Station which displays radio controlled time, date, indoor and outdoor
More informationRemote Control Outlets Operating Instructions
Remote Control Outlets Operating Instructions - FOR INDOOR OR OUTDOOR USE - IMPORTANT SAFEGUARDS Signal Word Definitions NOTE: These are general definitions only; all may not pertain to the actual product
More informationThe Interfit S1. AC/DC Powered TTL/HSS Flash. Instruction Manual.
The Interfit S1 AC/DC Powered TTL/HSS Flash Instruction Manual www.interfitphotographic.com Interfit S1 Battery Powered TTL/HSS Flash Unit What s cool about the Interfit S1? The S1 is the world s first
More informationUniversal Radio Cord Dimmer Order No.: Function
Order o.: 0335 0 a) b) Function The permits radio-operated control of lighting fixtures. The device permits switching (short actuation) or dimming (long actuation) of the lighting. The dimmer is operated
More informationENVIRONMENTAL PROTECTION
ENVIRONMENTAL PROTECTION Do not dispose of this product with the normal household waste at the end of its life cycle. Return it to a collection point for the recycling of electrical and electronic devices.
More informationOn-Line Cardio Theater Wireless Digital Transmitter Installation and Instruction Manual
On-Line Cardio Theater Wireless Digital Transmitter Installation and Instruction Manual Full installation instructions accompany your Cardio Theater equipment order. This On-Line version of our Installation/Instruction
More informationENCORE 300 SERIES INSTALLATION AND OPERATING INSTRUCTIONS
ENCORE 300 SERIES INSTALLATION AND OPERATING INSTRUCTIONS Copyright 2002-2006 PRI Ltd. 9600-3004-2 Issue C Information contained within this document is subject to change without notice and does not represent
More information1 Safety instructions. 2 Device components. Radio bus system. Radio socket outlet adapter for dimming Order No. : Operating instructions
Order No. : 1185.. Operating instructions 1 Safety instructions Electrical equipment may only be installed and fitted by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationProHead. User s Guide
ProHead User s Guide 2Profoto ProHead Profoto ProHead Thank you for choosing Profoto. Thanks for showing us your confidence by investing in a ProHead unit. For more than four decades we have sought the
More informationDigital Electronic Thermostat With RF
RT300RF Manual Altech 005_89 06/05/2014 08:56 Page 1 Digital Electronic Thermostat With RF Instruction Manual Model No ALTHC015 RT300RF Manual Altech 005_89 06/05/2014 08:56 Page 2 2 ALTHC015 INSTRUCTION
More informationfocushand 2 Users Manual FocusHAND System description
FocusHAND System description focushand 2 Users Manual FocusHAND is a wireless remote control unit with a DMX output, to be used for controlling lighting fixtures while focussing them. This means that the
More informationLMM31. Dimmer Micromodule, 1 load USER MANUAL 20410/ LMM31 ALL RIGHTS RESERVED MARMITEK
LMM31 Dimmer Micromodule, 1 load USER MANUAL 20410/20111019 LMM31 ALL RIGHTS RESERVED MARMITEK TABLE OF CONTENTS TABLE OF CONTENTS... 2 SAFETY WARNINGS... 3 HOW DOES MARMITEK X-10 WORK?... 4 ADRESSES...
More informationEC5401B. B-Tronic EasyControl. Assembly and Operating Instructions. Wall/hand-held transmitter, 1-channel, bidirectional
B-Tronic EasyControl EC5401B en Assembly and Operating Instructions Wall/hand-held transmitter, 1-channel, bidirectional Important information for: Fitters / Electricians / Users Please forward accordingly!
More informationOperation. 1 of 14. Serial number label
Telecody Keypad Transmitter (US) WARNING There is a possible risk of injury or death if safety instructions will not be observed. Please read and follow all instructions in this manual as well as the information
More informationU S E R S M A N U A L
U S E R S M A N U A L T H E R M O R E G U L A T O R T R 5 0 0 / T R 5 0 1 S E R I E S HUNDREDTHS VERSION ENGLISH V.1.2 TABLE OF CONTENTS -1- Introduction... page 2-2- Technical specifications -3- Description
More informationAT-SL-ADR & AT-SL-ADR/SA
AT-SL-ADR & AT-SL-ADR/SA RF 1-10V + relay controller Product Guide Overview The AT-SL-ADR and AT-SL-ADR/SA are wireless controllers with two output channels capable of controlling incandescent, fluorescent
More informationThe universal input/output device is a DIN rail mounted device. It is connected to the EIB via a bus connecting terminal.
, GH Q631 0026 R0111 SK 0097 B97 The universal input/output device is a DIN rail mounted device. It is connected to the EIB via a bus connecting terminal. The device has 32 freely programmable inputs/outputs,
More informationWiring Techniques for Wiring a Lamp
Supplies and Tools that you will need: Provided in your kit: Polarized lamp plug, 9 of SPT-1 18 AWG parallel lamp cord, bushings and grommets Items that you will need to provide: Phillips screwdriver,
More informationComfort Digisystem User Manual. SecureStream Technology. Microphone DM05. English
Comfort Digisystem User Manual SecureStream Technology Microphone DM05 English User Manual Table of Contents Page Introduction to the Comfort Digisystem 3 Presenting the Microphone DM05 3 Functions of
More informationRadioStar INTRODUCTION
CONTENTS INTRODUCTION...2 PACK CONTENTS...2 SAFETY INSTRUCTIONS...3 DEFINITION OF SYMBOLS...4 RECOMMENDED TOOLS...4 ASSEMBLY INSTRUCTIONS...5 RADIOSTAR MIRROR FUNCTIONS...7 SIDE INTEGRATED CONTROL PANEL...8
More informationTOP SERVO SIGNAL 5 SERVO SIGNAL 3 SERVO SIGNAL 4 SERVO SIGNAL 6 T B T B T B T B T B SERVO TRIGGER 1 BOTTOM
Micro Miniatures Servo Controller Channel Location of connections and switches TOP SERVO SIGNAL SERVO SIGNAL 7 SERVO SIGNAL 6 SERVO SIGNAL 5 SERVO SIGNAL SERVO SIGNAL SERVO SIGNAL SERVO SIGNAL SIGNAL COMMON
More informationRadio remote control.
Page 1 of 5 The radio remote control is functionally integrated in the general module of the ZKE. The antenna integrated in the rear window on the E46 Sedan, Sport Wagon, Coupé and E83 X3 is used as the
More informationWiring Instructions for 10, 16 & 20 Function, 92 & 93 Series, FET Receivers.
Wiring Instructions for 10, 16 & 20 Function, 92 & 93 Series, FET Receivers. 92220.02E 1 1. The Receiver is designed to carry a maximum of 15 Amps. That is, for example,15 Amps through one output or 5
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationSABRETrap Control. Description
SABRETrap Control Features Rugged radio remote control One transmitter can control Many receivers Waterproof receiver to IP68 Transmitters available with 1, 3,4 and 8 Switches Supplied ready to operate
More information200, 201 Series Radio Telemetry Transmitters
200 DIN Rail Transmitter Encoder Up to 8 Input Channels Volt Free contact Inputs via Screw Terminals 12 / 24Vdc Supply Range; 433MHz Up to 200 Metres 433MHz NB Up to 1,000 Metres 458MHz Up to 6,000 Metres
More informationFSP-211 DIGITAL HIGH/LOW PIR FIXTURE INTEGRATED SENSOR
FSP-211 DIGITAL HIGH/LOW PIR FIXTURE INTEGRATED SENSOR CAUTIONS INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A Fixture Pipe (3) B Coupling (3) C Canopy Pipe (3) D Middle Canopy Can E Clutch (3) F Plastic Sleeve (3) G Side Canopy Can (2) H Set Screw (3) I Middle Crossbar J #10 Screws (4)
More informationProfoto B1 500 AirTTL. User s Guide
Profoto B1 500 AirTTL User s Guide Profoto B1 500 Air TTL 2 Congratulations on your new Profoto product! Profoto B1 500 Air TTL Regardless if you chose a new flash or a new light-shaping tool, know that
More informationOverview Installation & Connection Mounting
Overview The Keene K-LAB-20 is compact, powerful stereo amplifier built onto a standard size UK double gang wall plate. It provides 20W (RMS per channel) of amplification eliminating the need to make space
More informationOperating instructions Flat-Type Wall-Mounted Radio Control
Operating instructions Flat-Type Wall-Mounted Radio Control Insert 1. Function The wall-mounted radio control insert permits remote control of all receivers of the Funk-Management system. This wall-mounted
More informationVELA-RX MOTORE 220V 500W
VELA-RX MOTORE 220V 500W Electronic control unit with UP, DOWN and STOP functions for managing 230 V, max. 500 W motors via wire and/or radio 1 INDEX 1 - PRODUCT FEATURES 1.1 - TECHNICAL DATA 1.2 - DESCRIPTION
More informationTX4400 UHF CB RADIO INSTRUCTION MANUAL TX4400 INSTRUCTION MANUAL PAGE 1
TX4400 UHF CB RADIO INSTRUCTION MANUAL TX4400 INSTRUCTION MANUAL PAGE 1 TABLE OF CONTENTS GENERAL................................... 3 FEATURES.................................. 3 BASIC OPERATION...4 Front
More informationWIRELESS 868 MHz WEATHER STATION
WIRELESS 868 MHz WEATHER STATION Instructions Manual INTRODUCTION: Congratulations on purchasing this Weather Station with wireless 868 MHz transmission of outdoor temperature and display of indoor temperature,
More informationRU210. Dual Multi-UHF Wireless System. Item ref: UK, UK User Manual. Version 1.0
RU210 Dual Multi-UHF Wireless System Item ref: 171.970UK, 171.971UK User Manual Version 1.0 Caution: Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty
More informationWIRELESS MOTION SENSOR USER MANUAL MULTI LANGUAGE START-LINE TRANSMITTER APIR-2150
START-LINE TRANSMITTER APIR-2150 USER MANUAL MULTI LANGUAGE Item 71091 Version 1.0 Visit www.trustsmarthome.com for the latest instructions WIRELESS MOTION SENSOR 1 2 3 4 5 6 7 8 9 10 11 EN APIR-2150 WIRELESS
More informationJUMO Wtrans E01. Measuring probe for humidity, temperature, and CO 2 with wireless data transmission. Brief description. Universal Wtrans receiver
Page 1/13 JUMO Wtrans E01 Measuring probe for humidity, temperature, and CO 2 with wireless data transmission Humidity from 0 to 100 % RH (incl. -40 to +80 C) or CO 2 from 0 to 2000/5000/10000 ppm or Temperature
More informationArtistic Licence. Rail-Pipe HC. User Guide. Version 1-6. Rail-Pipe HC User Guide
Artistic Licence Rail-Pipe HC User Guide Rail-Pipe HC User Guide Version 1-6 Please read these instructions before using the product. This product has been designed & manufactured for professional use
More informationTD - Power Supply LP DALI&Switch Dim Mono PRE (CV) MM-IP20 User Manual
TD - Power Supply LP DALI&Switch Dim Mono PRE (CV) MM-IP20 User Manual Item no.: NT-244-101 1. Product Description The TD-Power Supply SC DALI & Switch Dim Mono is a dimmable 24V constant voltage LED driver
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationProduct and Applications Description
Product and pplications Description Diagram The transmitter 230V wave UP 110 (Diagram ) is a flushmounted device with radio communication for the wireless operation of room functions. It is possible to
More informationWireless Ceiling Mount Sensor
Wireless Ceiling Mount Sensor Lutron s occupancy and vacancy sensors are wireless ceiling-mounted battery-powered passive infrared (PIR) sensors that automatically control lights via RF communication to
More informationWireless Z-Wave Control ZRP-100US Z-Wave Repeater USER MANUAL. Introduction
Wireless Z-Wave Control ZRP-100US Z-Wave Repeater USER MANUAL Introduction Thank you for choosing ZRP-100 Z-Wave Repeater product! ZRP-100 is a Z-Wave repeater with best RF performance to repeat Z-Wave
More informationRCR-24 中文 GB. Version 1
RCR-24 中文 GB Version 1 GB Please note not all AC adapters are alike. The AC adapter that is included with this radio is designed to be used exclusively with this device. Do not use an AC adapter that differs
More informationInstallation Instructions Student 101 Fume Cupboard
Installation Instructions Student 101 Fume Cupboard Refer drawing on next page 0. If your fume cupboard is supplied with a flatpack bench frame, see step1. If your fume cupboard will be mounted on an existing
More informationGLASS GLOBE MOBILE 6-ARM CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [6] (E) Screws [4] (F) Nut [1] (G) Extension rods [3] (H) Transformer [1] (I) Arm counterweights [6] (J) 1.6W LED
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
T0436 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local
More informationWIRELESS 868 MHz TEMPERATURE STATION Instruction Manual
WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this temperature station with wireless 868MHz transmission. It not only displays the indoor temperature
More informationModular Radio Telemetry System
Simple to Use Remote Control 8 Channels per Transmitter 16 Channels per Receiver Upto 48 Transmitters per system Auto Transmit Mode Secure RF Protocol Automatic Watchdog Transmission Range: Upto 200 metres
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationluxcontrol lighting control system basicdim basicdim ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor
ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor Product description Compact dimensions for luminaire installation For up to 10 DSI or LI devices (max. 5 per output channel)
More informationOperating instructions. Radio weather station
Operating instructions Radio weather station 0334.. Notes regarding the battery Batteries and button cells do not belong in the hands of children. Contact a doctor immediately if a button cell has been
More informationLaser LA-4P. Operating instructions
Laser LA-4P GB Operating instructions A 1 2 3a 5 3c 3b 3a 4 11 11 6 10 7 14a 14b 14c 12 9 8 B C 2. 1. D E F Ø 50mm - 115 mm Ø 2-4,5 G I K s > 6m > 20ft L M N P1 Q O 13 P2 GB Operating instructions The
More informationInstallation & Operation Manual
The eco-friendly solution to hard water SB-1200, SB-2000, SB-2800, SB-3600 & SB-4000 Installation & Operation Manual 10/13 Industrial Electronic Descaler 120/240 VAC (Auto Selected) Table of Contents Section
More informationThe Interfit S1 Battery Powered TTL/HSS Flash
The Interfit S1 Battery Powered TTL/HSS Flash Instruction Manual www.interfitphotographic.com Interfit S1 Battery Powered TTL/HSS Flash Unit What s cool about the Interfit S1? The Honey Badger is the perfect
More informationKNX manual 1-channel flush-mounted switch actuator SU 1
KNX manual 1-channel flush-mounted switch actuator SU 1 4942520 2018-10-04 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The SU 1 application programme 7 4.1 Selection in the product
More informationLMLR-710 (Plug-in type door chime receiver) LMLT-711 (push unit door chime transmitter)
MODEL: LMLR-710 (Plug-in type door chime receiver) LMLT-711 (push unit door chime transmitter) FEATURE: * 67 million self-learning coding RF wireless operation system. No interference with neighbors. *
More informationS-Series Digital Thermostat
ST320RF Manual Version 004 CMYK:Layout 1 1/9/10 09:57 Page 1 S-Series Digital Thermostat Model No ST320RF 2 Instruction Manual ST320RF Manual Version 004 CMYK:Layout 1 1/9/10 09:57 Page 2 2 ST320RF Manual
More information433 MHZ TEMPERATURE STATION Instruction Manual
433 MHZ TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this innovative 433MHz Temperature Station which displays the time with up to the minute indoor and up to three
More informationRF-RR-T 24V Powered Routers/Temp Sensors
Page 1 of 5 RF-RR-T 24V Powered Routers/Temp Sensors Features: Benefits: Proven 802.15.4 low power network Complete range of sensor types Allows networks to be expanded Power status LED Network activity
More informationWalkie-Talkie. User Manual and Instruction. Getting Started
Walkie-Talkie User Manual and Instruction Getting Started Installing the AA Batteries Your radio uses 3 AA Alkaline batteries. 1. With the back of the radio facing you, lift the battery latch up to release
More informationW I S E C O N T R O L S H O M E & G A R D E N W I S E D I M W I R E L E S S R A D I O T E C H N O L O G Y W I S E C O N T R O L S.
WISE CONTROLS H O M E & G A R D E N W I S E D I M W I R E L E S S R A D I O T E C H N O L O G Y W I S E C O N T R O L S. C O M reliable simple 2 year guarantee wireless easy affordable CONTENTS 1 CONTENTS
More informationReference number Dimensions Lamp Light colour
1 LED STRIPS PRO up to 152 lm/w LESS IS MORE FLEX: LED strip PRO Type of Protection: IP 00 IP 66 CVD Protection Class: III Flexible LED strip on roller (5 m). Mounting using 3M Thermal double-sided tape.
More informationInstruction Manual. for Media Monkey. 1
TM TM Instruction Manual for Media Monkey www.audioaperemote.com 1 Congratulations on acquiring your fine Audio Ape product Let s dive right in, getting up and running is a snap. Here are the components:
More informationROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS
ROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. IMPORTANT
More informationName Class Date. Brightness of Light
Skills Practice Lab Brightness of Light IN-TEXT LAB CBL VERSION The brightness, or intensity, of a light source may be measured with a light meter. In this lab, you will use a light meter to measure the
More informationENGLISH PORTUGUÊS NEDERLANDS DAB200
DEUTSCH ENGLISH FRANÇAIS NEDERLANDS ESPAÑOL PORTUGUÊS NORSK DAB200 Contents Introduction..... 2 What is DAB + Digital Radio?.... 2 Setting up..... 3 Backlit display.... 4 Using headphones...... 4 Your
More informationLOAD AWG Solid CU Wire Only LINE NEUT FSP-211. High/Low PIR Occupancy Sensor 230 VAC, 50 Hz 1200W max ballast 5E4
DESCRIPTION AND OPERATION The is a motion sensor that dims lighting from high to low based on movement. This slim, low-profile sensor is designed for installation inside the bottom of a light fixture body.
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationWireless wall transmitter, 1-gang with inscription space, Wireless wall transmitter, 3-gang with inscription space
Wireless wall transmitter, 1-gang with inscription space Order No. : 5331.. Wireless wall Order No. : 5333.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected
More informationFL ballasts Electronic dimming. PCA T8 ECO lp Y II, W ECO T8
T8 PCA T8 ECO lp Y II, 18 58 W ECO T8 Product description Processor-controlled ballast with y II inside Highest possible energy class CELMA EEI = A1 BAT 1 Noise-free precise control via DALI or DSI signal,
More informationLPTDX CHANNEL DIMMER PACK
12-CHANNEL DIMMER PACK 1. Introduction To all residents of the European Union Important environmental information about this product This symbol on the device or the package indicates that disposal of
More informationPHASED OUT. Digital dimmable ballasts for fluorescent lamps EXCEL series. PCA TCL EXCEL one4all lp Y, 55 W Compact and T5c fluorescent lamps
EXCE series Product description Processor-controlled ballast with y inside oise-free precise control via DSI signal, switchdim, corridorfuctio or I I-MEMORY Extended I commands OEM-specific reserved memory
More informationwww.greenelectricalsupply.com Installation Guide Model: WLVD Wireless Low Voltage Dimmer (Receiver) Specifications: Power Supply 24 V DC Place on 24V power line prior to light load. 10A Maximum Load Package
More informationRGB Cuttable every 100 mm. 60 LEDs per meter (LED Pitch 16,7 mm). Constant luminous flux by means of transistor
LED STRIPS 1 LESS IS MORE FLEX: LED strip ECO Type of Protection: IP 00 IP 66 CVD Protection Class: III Flexible LED strip on roller (5 m). Mounting using 3M Thermal double-sided tape. Voltage 24 V. ECO
More informationPRO Professional Radio Control Series Applications
204 205 Ready to Use Remote Control 4, 8/16 Channel Systems Range: Up to 200 metres at 433MHz Up to 1,000 metres at 433MHz NB Relay Outputs: Momentary, Latching, Timed Receiver IP65 Applications Lighting
More information