LK Wireless Room Control Cq

Size: px
Start display at page:

Download "LK Wireless Room Control Cq"

Transcription

1 LK Wireless Room Control Cq Description LK Wireless Room Control Cq consists of a LK Room Thermostat Cq-n (transmitter) and a LK Receiver Unit Cq 8 (8 channel receiver unit). The range also includes a single channel receiver; for further information see separate instructions for LK Receiver Unit Cq. LK Repeater Cq (signal amplifier) is available as an accessory for use where transmission conditions are poor. For more information see separate instructions for the LK Repeater and the LK Repeater-HW. Design The LK Room Thermostat Cq-n regulates temperature in the rooms they are located via radio signals to the LK Receiver Unit Cq 8. The Receiver Unit converts the radio signals to control signals to activate individual manifold actuators. Therefore should the Receiver Unit be located nearby the manifold. specially designed for thermoelectric actuators. The control signal is calculated from the variance between the actual temperature and the set temperature and is emitted in the form of signals with varying pulse and rest ratios. The sum of the signal and rest period is always 0 minutes, to prevent rapid temperature variations switching the thermostat on and off rapidly. LK Room Thermostat Cq-n The LK Room Thermostat Cq-n is available in two colours: white and silver grey. The LK Room Thermostat Cq-n regulates room temperatures via radio signals to the LK Receiver Unit Cq 8. Regulation takes place using pulse width modulation (PBM) regulation that is Assembly of the LK Room Thermostat Cq-n Open the Room Thermostat by pulling off the temperature scale dial and loosening the screw now visible. Flex the cover to the left until it becomes loose. Position and fix the Room Thermostat as per the installation diagram. For the Room Thermostat to function properly, please note of the following: Mount the thermostat on an inner wall so it is ventilated and approx.. metres above the floor. The thermostat should not be exposed to direct sunlight or other heat sources. Do not mount the thermostat close to a radio, TV or another transmitter. Do not mount the thermostat close to metal doors, metal cabinets or similar as these may shield the radio signal. EN..C

2 LK Receiver Unit Cq 8 long periods, e.g. during the summer months. It is possible to connect a system s circulation pump to the Receiver Unit. The unit s pump logic shuts off the circulation pump when all the actuators are closed. The pump is exercised once per day to ensure it is working correctly. Read more under the heading Pump control. Design The LK Receiver Unit Cq 8 has eight channels. This means that a maximum of eight LK Room Thermostat Cq-n can be linked to the Receiver Unit. It is possible to link a thermostat to more than one channel. The unit can also control the on/off switch, for example, on a boiler. Read more under Boiler control. Display Each channel can control up to eight LK Actuators. However, there is only room for a maximum of four actuators per channel; if connecting eight actuators to one channel. The additional four must be connected using an external junction box. The maximum number of actuators that can be connected to the Receiver Unit must not exceed. The unit is supplied with an integrated -volt transformer. The Receiver Unit is supplied with a timer for eight channels for controlling each channel. Information about the status of a channel is shown in the LCD display. See more information under Display. The Receiver Unit is supplied with a clock that makes it possible, for example, to lower the temperature at night in selected rooms (night setback). The unit also comes with six different time profiles. Five of the profiles have fixed values and one is programmable. For more information see Programming of the clock under Time Profiles. Once a day all actuators are exercised to avoid potential seizure problems with valves closed for The Receiver Unit is also supplied with a display. See the table on next page for information about the functions. EN..C

3 Room to Room 8 Transmitter indicator for each channel/ room. On = Relay on (heat on) and indicator lamp is on. Flashing = fault. Shows comfort or economy temperature for the respective rooms: MOON = Economy temperature No MOON = Comfort temperature R to R8 to 7 Day of the week MODE Operational adjustment + - Change values OK Confirm Cooling active (factory installed function) To enable programming after removing the locking function (requires a qualified installation engineer), press briefly on the OK button until the display lights up. Pump Control Channel 8 on the Receiver Unit can be used to control the installation s circulating pump, instead of room thermostat control. Provided a thermostat has not been programmed to channel 8, the channel functions as a one pole potential free, circuit breaker for an installation s circulation pump. Humidity indicator (factory installed function) Comfort temperature (programmable) Economy temperature (programmable) Party function Vacation function Indicators of normal operation: - Current day of week -7 (= Monday) - Time - Room with reduced temperature. In the illustration rooms R, R, R and R7 have lowered temperatures. Display shows: e.g.. e.g. 008 e.g h 000 d r P 0 00 L del In:0 CO:ON See this section for additional information Clock, setting time Clock, setting year and day of week Clock, setting month and date Party time Vacation function Time profile Time profile, Time profile 6 Memorisation mode/activate Erase channels in memory Change NO/NC function Factory installed function The pump starts and the light diode for channel 8 lights up as soon as one of the channels to 7 requests heat. The pump is turned off and the light diode for channel 8 turns off ten minutes after all channels have stopped requesting heat. Once every hours the pump is exercised. The exercising takes place at the same time as the valve exercising. Connect the pump according to the circuit diagram below. If there is more than one connection box in the installation, the boxes must be connected to each other for the pump logic to function correctly. NOTE. Mount the pull-relief included in the kit when connecting the pump. EN..C

4 R R R R R R6 R7 R8 P R8 R8 R8 P L N ~ ~ exercising The actuators are exercised once per day for prevent the valves from seizing. If the valve exercising is not required it can be set to off for each channel by taking off bridge circuit in the thermostat. Take off the temperature dial, loosen the screw and lift off the cover. Remove bridge circuit, marked BR in the circuit diagram. Boiler (heater) control Channel 7 on the Receiver Unit can be used to control the installation s boiler/heater, instead of thermostatic room temperature control. Provided a thermostat has not been programmed to channel 7, the channel functions as a one pole potential free, circuit breaker for the system s boiler/heater. If one of the channels -6 requests heat the circuit breaker is closed and the indicator light for channel 7 comes on. The boiler/heater connected will receive the on signal. The boiler/heater comes on and will be connected until all channels stop requesting heat. There is no idle delay. In addition, there is no exercising function for channel 7 when the channel is used to connect to a boiler. Connect the boiler/heater to channel 7 only as shown in the circuit diagram below. If there is more than one connection box in the installation, the boxes must be connected to each other. NOTE. Mount the pull-relief included in the kit when connecting the boiler. R7 L N ~ ~ Heater X L N ~ ~ Party time The unit is fitted with a function called Party time that offers a simple way of overriding the night set-back settings for - hours.. Activate the function by pressing on the mode button four times. The display will show the number of hours and the arrow on the display will indicate the party symbol.. Press OK once. The digits for the hours will flash. Press + or to set the number of hours during which you wish to override the night settings.. Press OK once to confirm the setting. The display will return to the main menu. Once the selected time period has elapsed the unit returns to the original programming. While the setting is activated the arrow will indicate the party symbol. To remove the Party Time setting before it has fully elapsed, follow the instructions above and set the clock to 00. EN..C

5 Vacation function The unit is fitted with a Vacation function that offers a simple way of reducing the temperature in a room for a longer period of time, for example, during a vacation.. Activate the function by pressing on the mode button five times. The display will show the number of days and the arrow on the display will indicate the vacation symbol.. Press OK once. The digits for the days will flash. Press + or to set the number of days.. Press OK once to confirm the setting. The display will return to the main menu. While the vacation setting is activated the arrow will indicate the vacation symbol. At midnight on the last day set for a vacation period the unit will return to the original programming. To remove the vacation function setting before it has fully elapsed, follow the instructions above and set the number of days to 00. Cooling The unit is factory installed to be able to control an installation with comfort cooling. Contact the LK Technical Backup Team for more information about this function. Installation The Receiver Unit should be wired to a 0-volt power supply. The Receiver Unit must only be installed by a qualified electrician according to the circuit diagram and in keeping with the electrical safety regulations in force at the time. In order to comply with protection class the necessary installation measures must be followed. Mount the DIN rail mount on the wall with the appropriate fixings, making sure there is sufficient room to be able to open the Receiver Unit s door. Snap the Receiver Unit and transformer onto the DIN rail mount. Connecting Actuators NOTE! Shut off the power before opening the cover to the Receiver Unit. Each channel (marked R, R, etc.) is split into two halves so that a total of four actuators can be connected. (By using an external junction box, 8 actuators may be connected per channel.) The valve is connected to channels 7 (R7) and 8 (R8) between terminals and. NOTE! On channel 7 and channel 8, terminals and are to be connected when the actuator is connected. If an actuator is connected to channel 7 and channel 8 the alternative functions control of boiler (channel 7) and pump logic (channel 8) cannot be used at the same time. For more information look under the headings Boiler control and Pump control. Each Receiver Unit can have a maximum of actuators connected. If a control zone (room) consists of more than four actuators then any remaining actuators for a room can be connected to another channel. Because it is possible to connect a thermostat to more than one channel, in theory, it is possible to control actuators from one thermostat. R R R R R R6 R7 R8 EN..C

6 Memorising/Activating Memorising of the thermostat to one channel R R R R R R6 R7 R8. Activating the Receiver Unit The Receiver Unit is activated by pressing Mode several times. When the letter L is displayed press OK once. The first channel indicator light will then begin to flash (Room ). (Any previously memorised channels will show an indicator light.) Move between the channels using the +/- button until the required channel is reached. Press OK. Now the indicator light for the selected channel will flash while the display counts down in seconds.. Activating the thermostat D C A B Check that the main switch (A) is on, in the lower position towards the heating symbol as in illustration. Activate the room thermostat by holding down on the black button (B) and briefly press the upper black button (C). When the green indicator light on the thermostat comes on you can release the lower black button (B). The thermostat is now activated for memorisation.. Activating the selected channel When the thermostat has found its channel, the display will cease counting down. Activate it by pressing once on the upper black button on the thermostat (C). The indicator light on the thermostat will go out and the selected channel on the Receiver Unit will start to flash. Press Mode once. Test the connection by turning the dial up and down on the thermostat. The selected channel on the Receiver Unit will go on/off. Repeat the above steps to set the next thermostat. Open the door on the Room Thermostat and take off the transport protection covering from the batteries. EN..C

7 Memorising a thermostat for several channels R R R R. Activating the Receiver Unit The Receiver Unit is activated by pressing Modeseveral times. When the letter L is displayed press OK once. The first channel indicator light will then begin to flash (Room ). (Any previously memorised channels will show a continuous indicator light.) Move between the channels using the +/- button until the required channel is reached. Press OK. Now the indicator light for the selected channel will flash while the display counts down.. Activate the Thermostat Open the door on the Room Thermostat and take off the transport protection covering from the batteries. D C A B R R6 R7 R8 Check that the main switch (A) is on, in the lower position towards the heating symbol, as in the illustration. Activate the Room Thermostat by holding down on the black button (B) and briefly press the upper black button (C). When the green indicator light (D) on the thermostat goes out you can release the black button (B). The thermostat is now activated for memorisation.. Activating the selected channel When the thermostat has found its channel the display will stop counting down. Select the next channel to be controlled by the same thermostat using the +/- buttons. Press OK once. The selected channel will now flash and the display will count down. When the thermostat has found its channel the display will stop counting down. Repeat the above steps for each channel to be controlled by the same thermostat. Activate all the selected channels by pressing once on the upper black button on the thermostat (C). Press once on Mode. Test the connection by turning the dial on the thermostat up and down. The selected channel on the Receiver Unit will switch on/off. EN..C

8 Clock The Receiver Unit is equipped with a pre-programmed clock that makes it possible, for example, to lower temperatures at night (night set-back) in one or more rooms. The unit has six different profiles five have fixed values, the sixth is freely programmable. See under Time profiles for more information. Follow these instructions if changes to the preprogrammed values for the clock are required. Setting the year and day of the week. Press on the Mode button once, the selected year will be displayed, e.g Press OK once, the digit for units will flash, press + or to change the value.. Press OK once, the digit for decades will flash, press + or to change the value.. Press OK once, the arrow for the day of the week will flash (Monday =), press + or to change the value.. Press OK once to activate the new setting. The display will return to the main menu. Setting the time. Press the mode button three times. The actual time will be displayed in the format HH.MM (e.g. quarter past one =.). Press OK once, the digit for hours will begin to flash. Press + or to change the value.. Press OK once, the digit for tens for the minutes will begin to flash. Press + or to change the value.. Press OK once, the digit for units for the minutes will begin to flash. Press + or to change the value.. Press OK once to activate the new setting. The display will return to the main menu. Time profiles The factory setting for all the channels is time profile, i.e. comfort temperature at all times. See the illustration below. The unit has six different time profiles. Profiles to have fixed values as per the illustration. The sixth time profile can be programmed. See the section Time profile 6. Setting the month and the date. Press the mode button twice. The month and date will be displayed in the format DD.MM (e.g. December =.). Press OK once, the digit for the month will begin to flash. Press + or to change the value.. Press OK once, the digit for tens for the date will begin to flash. Press + or to change the value.. Press OK once, the digit for units for the date will begin to flash. Press + or to change the value.. Press OK once to activate the new setting. The display will return to the main menu. Each room can be allocated an optional time profile for an optional number of days of the week.. Press the mode button six times until the display shows rp (room, program ). The arrow points to = Monday.. Press OK once, the room s number (e.g. r) will flash. Press + or to change the value.. Press OK once, the arrow pointing to the day will flash. Press + or to select an individual day or group of days. You can select a single day, Monday to Friday (-), Saturday to Sunday (6-7) or a weekday (-7).. Press OK once, the number on the time profile will flash. Press + or to change the value.. Repeat the above steps for the other rooms. 6. Press mode to return to the main menu. EN..C

9 :00 6:00 9:00 0:0 :00 :00 :00 6:00 7:00 8:00 9:00 :00 :00 P P P P P P6 Time profile 6 The unit s sixth time profile can be programmed as desired. The shortest time interval between off and on is ten minutes. The first time switch for the day must be used for increasing the temperature beginning at 00:00. The last time switch for the day must be for lowering the temperature and cannot occur later than :0.. Press the mode button seven times. The display will show the time, for example, 0:00. The arrow will be pointing to the sun symbol.. Press OK once, the time will begin to flash. Set the required time for the first temperature increase using the + and buttons.. Press OK, the arrow is now pointing to the moon. Set the time for lowering the temperature.. Activate with OK. Repeat the above steps until your time profile is done.. Press mode to return to the main menu. Erasing memorised channels This function is used to erase all programmed channels. Restoring Factory Settings This function is used to restore the unit to the factory settings. The effect of restoring factoring settings will be that: All rooms will have time profile. Profile 6 will have the original factory setting. The vacation function will be set to 0. The Party function will be set to 0. The alarm function will be reactivated if it has been previously deactivated. Memorised thermostats and clock settings will not be affected. Restore factory settings by holding down the reset button using a pointed object. The reset button can be found between the + and buttons on the Receiver Unit. Activate by one Press on the OK button. Testing connections To test that all the connections/actuators are working it is possible to supply all connections with power.... Press mode until del is displayed. The indicators for the channels that have been set in the memory will come on. Press OK and del will start to flash. Press OK to erase all the stored channels and return to the main menu.... Press Mode until A of is displayed. Press OK, of will flash. Press + or to change the value. of = all connections are off. on = all connections are on. Press Mode to return to the main menu. EN..C

10 Switch the NO/NC function The unit can, if required be modified to power normally closed (NC) or power normally open (NO) actuator. See instruction below.. Press the Mode button until In (or In 0 ) is displayed.. Press OK, In will flash. (or In 0 ). Press + or to change the value. In 0 = power normally closed device (NC) In = power normally open device (NO). Activate with OK, the unit will then return to the main menu. Error detection / Operational problems The Channel 7 and/or Channel 8 indicator light is on even though it has not been programmed. Channel 7 and 8 function for boiler control and pump logic when no thermostat has been assigned to these two channels. More information can be found under the headings Boiler control and Pump control. teries in the thermostat may need replacing. See more information under the heading Replacing the batteries. If the problem still persists even after replacing the batteries it may be necessary to strengthen the signal. This can be best achieved by using the LK Repeater. More information is available in the separate instructions for the LK Repeater. Range Control To determine the maximum range for a signal the following test can be performed.. The Receiver Unit is activated by pressing Mode several times. When the letter L appears on the display press OK once. The first channel (Room ) will flash. (Any channels memorised previously will have the indicator light showing). Select the required channel using the +/- button. Press OK. Now the selected channel will flash while the display counts down.. Activating the Thermostat. The actuators on channel 7 and/or channel 8 do not shut off. The connection between terminals and does not exist on Channel 7 and/or Channel 8. See the heading Connecting the actuator Problems with signal transfer If the signal between the thermostat and Receiver Unit is disrupted the indicator light for the affected channel will flash on the Receiver Unit. During a signal disruption the affected channel will deliver 0% heat output (NO only). If the Receiver Unit receives a signal from the affected thermostat the alarm will be automatically switched off. If the problem persists for more than 0 hours, in addition to the indicator light, an alarm sound will be emitted. The problem can be resolved by pressing the thermostat s reset button (button C). See the illustration under the heading Memorising/Activating. If the problem persists the bat- Open the door on the room thermostat and take of the transport protective covering from the batteries. Check that the main switch (A) is on in the lower position towards the heating symbol as in illustration. Activate the room thermostat by holding down the lower black button (B) and press once on the upper black button (C). D C A B EN..C

11 When the green indicator light on the thermostat comes on you can release the lower black button (B). The thermostat is now activated for range control. When the thermostat has found its channel the display will stop counting down and the indicator light for the selected channel will be on. Pick up the thermostat and move it until the light for the selected channel begins to flash. This means that the maximum range for the channel has been reached. Activate it by pressing once on the upper black button on the thermostat (C). The indicator light on the thermostat will go off and the selected channel on the Receiver Unit will begin to flash. Press Mode once. Test the connection by turning the dial on the thermostat up and down. The selected channel on the Receiver Unit will go on/off. The power lamp is off. Check there is power from the socket. Check that the fuse in the Receiver Unit is in position behind the unit s white plastic cover. Turn off the power before changing the fuse. Use the same type of fuse as a replacement: A inert. Power interrupts. Loss of power does not cause loss of data, all programming will be retained. The timer will continue to function with its own power source, but no information can be seen on the display. When the power resumes it can take up to ten minutes for all the channels to return to the programmed mode. Using batteries in the Room Thermostat. LK Room Thermostat Cq-n is supplied with two. V batteries (LR0). The batteries should last for two years. When the batteries need changing, the signal lamp on the thermostat flashes every seconds. Batteries should be replaced within a few days. The batteries are fitted under the thermostat s door. After replacing the batteries the thermostat will return to the chosen mode of operation. Press the thermostat s reset button to enable the thermostat to continue with the selected operational mode (button C) see the illustration under the heading Memorising/Activating. With depleted batteries the Receiver Unit will deliver 0% heat (NO mode only). CE certificate This control equipment can be used in all EU and EFTA countries. The manufacturer hereby states that the equipment complies with the fundamental requirements and other relevant requirements laid down in the directive R&TTE 999//EC. The manufacturer s declaration can be downloaded from Technical data Item name LK Receiver Unit Cq 8 Article no. 887 Supply Voltage 0 V 0 Hz Power requirement VA Fuse A inert Operating temperature Storage temperature Aerial Internal Output Signal 6 relay & alternating potential free Dimensions 90 x 0 x 80 mm Weight.0 kg Protection mode IP 0 Number of actuators /channel Max. 8 Number of actuators per box Note! A fully disruption free operation can not always be guaranteed with the technology available nowadays that allows free use of frequency bands. For this reason each installation must be individually tested. EN..C

OPERATING INSTRUCTIONS ARE ON PAGE 5. SECTION 2 Technical Data Transmitter Unit. RVHT 2 MULTI-FIT Programmable R/F Thermostat-Pair SECTION 1

OPERATING INSTRUCTIONS ARE ON PAGE 5. SECTION 2 Technical Data Transmitter Unit. RVHT 2 MULTI-FIT Programmable R/F Thermostat-Pair SECTION 1 OPERATING INSTRUCTIONS ARE ON PAGE 5 RVHT 2 MULTI-FIT Programmable R/F Thermostat-Pair SECTION 1 This Programmable Ravenheat R/F controlled room Thermostat RVHT 2, consists of 2 items: a Mobile Transmitter

More information

200 RTH OFF ON IN OUT ALARM RESET

200 RTH OFF ON IN OUT ALARM RESET 200 RTH OFF ON IN OUT ALARM RESET EN OWNER S MANU AL www.auraton.pl 2 3 Thank you for purchasing the modern temperature controller based on an advanced microprocessor. AURATON 200 RTH LCD FrostGuard function:

More information

INSTAT 868 Radio Frequency Single-Room Controls

INSTAT 868 Radio Frequency Single-Room Controls INSTAT 868 Radio Frequency Single-Room Controls Easy to operate wireless application HEATING People Performance Products Climate Controls Europe An Invensys company Radio Frequency Controls Single-room

More information

EBERLE THERMOSTAT & RECEIVER

EBERLE THERMOSTAT & RECEIVER EBERLE THERMOSTT & RECEIVER SIMPLIFIED INSTLLTION INSTRUCTIONS: Carefully connect the wires as on the next page diagram between the electric source and the heater. Once all is connected/installed, start

More information

S-Series Digital Thermostat

S-Series Digital Thermostat ST320RF Manual Version 004 CMYK:Layout 1 1/9/10 09:57 Page 1 S-Series Digital Thermostat Model No ST320RF 2 Instruction Manual ST320RF Manual Version 004 CMYK:Layout 1 1/9/10 09:57 Page 2 2 ST320RF Manual

More information

User Manual OFF ON IN OUT ALARM RESET AURATON RTH software ver. F0F

User Manual OFF ON IN OUT ALARM RESET AURATON RTH software ver. F0F www.auraton.pl User Manual software ver. F0F OFF ON IN OUT ALARM RESET AURATON RTH Thank you for purchasing this modern, advanced, microprocessor-based temperature regulator AURATON 2025 / AURATON 2025

More information

Wireless multizone receiver RDE-MZ6

Wireless multizone receiver RDE-MZ6 s 1 428 Wireless multizone receiver RDE-MZ6 for floor heating / zone heating systems Mains-powered RDE-MZ6 multizone wireless receiver (AC 230 V) DIN rail mounting 2-position control with On/Off output

More information

Wireless Room Thermostat Installation and Operation Y6630D1007

Wireless Room Thermostat Installation and Operation Y6630D1007 Wireless Room Thermostat Installation and Operation Y6630D1007 General safety instructions Contents 1. General safety instructions... 3 1.1. Commissioning the relay module HC60NG... 3 2. Overview... 4

More information

LP20RF & DIGISTAT+RF. Installation & User Guide PRINT. Radio frequency controlled room thermostat with dual channel programmer. Part number RF562DR

LP20RF & DIGISTAT+RF. Installation & User Guide PRINT. Radio frequency controlled room thermostat with dual channel programmer. Part number RF562DR Radio frequency controlled room thermostat with dual channel programmer Part number RF562DR Spares Part number 31003 Spares Part number 22590DR! For GREENSTAR CDi, GREENSTAR i JUNIOR and GREENSTAR Si MODELS

More information

Control solutions Biofloor

Control solutions Biofloor MR24 Central radio controller 24V Connect COMAP offers the Connect control system as part of its underfloor heating and cooling solution. Composed of a central radio control module (MR24), wireless digital

More information

Radiocontrol F. Floor Heating Controller Radio control system for floor heating

Radiocontrol F. Floor Heating Controller Radio control system for floor heating Radiocontrol F Floor Heating Controller Radio control system for floor heating IMI HEIMEIER / Floor Heating Control / Radiocontrol F Radiocontrol F The Radiocontrol F radio control system for controlling

More information

2025 RTH 2025 P 2025 OFF ON IN OUT ALARM RESET

2025 RTH 2025 P 2025 OFF ON IN OUT ALARM RESET 2025 RTH 2025 P 2025 OFF ON IN OUT ALARM RESET EN OWNER S MANU AL www.auraton.pl 2 Thank you for purchasing this modern, advanced, microprocessor-based temperature regulator AURATON 2025 / 2025 P / 2025

More information

Digital Electronic Thermostat With RF

Digital Electronic Thermostat With RF RT300RF Manual Altech 005_89 06/05/2014 08:56 Page 1 Digital Electronic Thermostat With RF Instruction Manual Model No ALTHC015 RT300RF Manual Altech 005_89 06/05/2014 08:56 Page 2 2 ALTHC015 INSTRUCTION

More information

AHC-XP. Dewpoint-guided Power Controller for Glass and Handrail Heaters. Front view. Characteristics

AHC-XP. Dewpoint-guided Power Controller for Glass and Handrail Heaters. Front view. Characteristics Dewpoint-guided Power Controller for Glass and Handrail Heaters Front view Characteristics Dew point-guided power controller for cost-optimized operation of glass and handrail heaters Digital display of

More information

INSTRUCTION MANUAL DT10RF OPTIMISING PROGRAMMER UK/IE OPERATING AND INSTALLATION

INSTRUCTION MANUAL DT10RF OPTIMISING PROGRAMMER UK/IE OPERATING AND INSTALLATION Hol Man Auto Day OPERATING AND INSTALLATION DIGISTAT OPTIMISER - Radio frequency controlled programmable room thermostat with domestic hot water programmer FOR GREENSTAR CDi AND GREENSTAR Si MODELS ALSO

More information

* _Ver.1* GP8 Radio CPL Radio DRIVER Energy manager

* _Ver.1* GP8 Radio CPL Radio DRIVER Energy manager GP8 Radio CPL Radio DRIVER Energy manager Delta Dore hereby declares that the equipment complies with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC The EC declaration

More information

AURATON 2020 AURATON 2020 TX RX Plus

AURATON 2020 AURATON 2020 TX RX Plus 0 I 31 EN AURATON 2020, AURATON 2020 TX RX Plus AURATON 2020 AURATON 2020 AURATON 2020 TX RX Plus Preliminary notes The manual includes the information on AURATON 2020 and AURATON 2020 TX RX Plus controllers.

More information

EUROSTER 2026/2026TX

EUROSTER 2026/2026TX EUROSTER 2026/2026TX - User Manual 1 EUROSTER 2026/2026TX 1. CHARACTERISTICS 4 different programs for each day of the week (28 different ranges and temperatures altogether). Time programming with 10 minutes

More information

TC 204 Heating Controller

TC 204 Heating Controller TC 204 Heating Controller ver. 1.32-01 The TC204 is a multi-purpose heating controller with built-in programs for different types of heating systems. General Data Power requirement 24 volts ac, 2 va Inputs

More information

User Instructions For TopTronic RS-10

User Instructions For TopTronic RS-10 User Instructions For TopTronic RS-0 409ENG-Dec0 Hoval Ltd Northgate Newark Nottinghamshire NG4 JN Phone 066 677 Fax 066 675 Index 409ENG-Dec0 Introduction Introduction... Controls... Display... User instructions

More information

RAMSES 784 HF Set 1. Bedienungsanleitung Uhrenthermostat 1. Operating Instructions Clockthermostat 14. Mode d emploi Thermostat à horloge 26

RAMSES 784 HF Set 1. Bedienungsanleitung Uhrenthermostat 1. Operating Instructions Clockthermostat 14. Mode d emploi Thermostat à horloge 26 309 484 01 RAMSES 784 HF Set 1 784 9 407 784 9 417 Bedienungsanleitung Uhrenthermostat 1 Operating Instructions Clockthermostat 14 Mode d emploi Thermostat à horloge 26 Gebruiksaanwijzing Klokthermostaat

More information

TAC 2112 Manual (GB),

TAC 2112 Manual (GB), TAC 2112 Manual T1 P1 0-004-7459-3 (GB), 1999-08-01 Contents TAC 2112 Manual Subject to modification. 1999 TAC AB Contents 1 About this manual... 1:1 1.1 Overview... 1:1 1.2 How to use this manual...

More information

Thank you for purchasing this product. If installing for someone else, please ensure that the instructions are handed to the householder.

Thank you for purchasing this product. If installing for someone else, please ensure that the instructions are handed to the householder. Instruction Manual TPSRF31 (181430) - BOSS TM Electronic RF Roomstat Thank you for purchasing this product. If installing for someone else, please ensure that the instructions are handed to the householder.

More information

Thermostat P. Thermostats Electronic room thermostat with clock for thermal actuators

Thermostat P. Thermostats Electronic room thermostat with clock for thermal actuators Thermostat P Thermostats Electronic room thermostat with clock for thermal actuators IMI HEIMEIER / Thermostats & Actuators / Thermostat P Thermostat P The Thermostat P room temperature controller is used

More information

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this compact 868MHz Temperature Station which displays radio controlled time, date, indoor and outdoor

More information

TABLE OF CONTENT A. Installation and Mounting Installation 3 2. Mounting Receiver Addressing... 5 B. Key Interface. 7 C.

TABLE OF CONTENT A. Installation and Mounting Installation 3 2. Mounting Receiver Addressing... 5 B. Key Interface. 7 C. TABLE OF CONTENT A. Installation and Mounting.. 3 1. Installation 3 2. Mounting.. 4 3. Receiver Addressing... 5 B. Key Interface. 7 C. LCD Interface...8 D. Start/Reset...9 E. Operation Mode.10 F. Time

More information

Model: 5301P INSTALLATION AND OPERATION INSTRUCTIONS

Model: 5301P INSTALLATION AND OPERATION INSTRUCTIONS Model: 5301P INSTALLATION AND OPERATION INSTRUCTIONS INTRODUCTION IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE This SKYTECH remote control system

More information

SERVICE-MANUAL ROOM TEMPERATURE CONTROLLER NEA 230V / 24V. Construction Automotive Industry

SERVICE-MANUAL ROOM TEMPERATURE CONTROLLER NEA 230V / 24V. Construction Automotive Industry ROOM TEMPERATURE CONTROLLER NEA 230V / 24V Construction Automotive Industry ROOM TEMPERATURE CONTROLLER NEA 230V / 24V TABLE OF CONTENTS 1....... Information and safety guidelines......................................................

More information

Radio motion detector comfort 1.1 m/2.2 m quicklink Order number

Radio motion detector comfort 1.1 m/2.2 m quicklink Order number Radio motion detector comfort 1.1 m/2.2 m quicklink Order number 8534 51.. Operating instructions 1. Safety instructions Electrical equipment may only be installed and assembled by a qualified electrician

More information

WLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING

WLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING WLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING DESCRIPTION: An electronic control panel used in conjunction with one pulse meter (a water meter with pulse output proportional

More information

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this temperature station with wireless 868MHz transmission. It not only displays the indoor temperature

More information

Radio Touch Order no.: 2880 xx. Operation and installation instructions. 1 Safety instructions. 2 Structure of the device (Figure 1) Radio Touch

Radio Touch Order no.: 2880 xx. Operation and installation instructions. 1 Safety instructions. 2 Structure of the device (Figure 1) Radio Touch Radio Touch Order no.: 2880 xx Operation and installation instructions 1 Safety instructions Electrical equipment must only be installed and assembled by a qualified electrician in accordance with the

More information

WIRELESS CONTROL UNIT FOR CONTROL OF ELECTRIC HEATING DEVICES (WITHIN ONE ROOM)

WIRELESS CONTROL UNIT FOR CONTROL OF ELECTRIC HEATING DEVICES (WITHIN ONE ROOM) PH-BSP WIRELESS CONTROL UNIT FOR CONTROL OF ELECTRIC HEATING DEVICES (WITHIN ONE ROOM) Wireless control unit Two-way radio communication on 433.92 MHz Comfortable solution of room heating Predictive system

More information

WIRELESS 433MHZ WEATHER STATION

WIRELESS 433MHZ WEATHER STATION WIRELESS 433MHZ WEATHER STATION INTRODUCTION: Congratulations on purchasing this Weather Station with wireless 433MHz, which displays time/date, indoor/outdoor temperature and humidity, and receives up

More information

Mx-D15 Intelligent Valve Actuator

Mx-D15 Intelligent Valve Actuator Application Small radio controlled, battery-powered actuator for room temperature control. For thermostat valve bodies for direct mounting on commercially available radiator valves for room-specific temperature

More information

INSTALLATION & PROGRAMMING MANUAL PROGRAMMABLE TIMER (MODEL LP-2)

INSTALLATION & PROGRAMMING MANUAL PROGRAMMABLE TIMER (MODEL LP-2) INSTALLATION & PROGRAMMING MANUAL PROGRAMMABLE TIMER (MODEL LP-2) Copyright Lencore Acoustics Corp. All rights reserved. April 2000 CONTENTS Introduction 3 Display 3 Keyboard 4 Installation 4 Set Up 4

More information

PRODUCT CATALOGUE TEMPERATURE CONTROL Grässlin products for individual control of temperature

PRODUCT CATALOGUE TEMPERATURE CONTROL Grässlin products for individual control of temperature PRODUCT CATALOGUE TEMPERATURE CONTROL Grässlin products for individual control of temperature Temperature control: Feel good at any time of year Room thermostats Heating time switches Excellent products

More information

DDC Series Dial Digital Controller INSTALLATION AND OPERATING INSTRUCTIONS

DDC Series Dial Digital Controller INSTALLATION AND OPERATING INSTRUCTIONS DDC Series Dial Digital Controller INSTALLATION AND OPERATING INSTRUCTIONS Thank you for choosing the Toro DDC (Digital Dial Controller) irrigation controller. The DDC incorporates the lates programming

More information

Room Temperature Controllers. for heating and cooling systems

Room Temperature Controllers. for heating and cooling systems 3 041 RCU10 RCU10.1 Room Temperature Controllers for heating and cooling systems RCU10... Choice of two-position or modulating PI control ON / OFF or PWM outputs for heating and cooling Operating modes:

More information

COD GB / 1.0 RBAND/UMS - RBAND/CSM

COD GB / 1.0 RBAND/UMS - RBAND/CSM INTRODUCTION DESCRIPTION The RadioBand system is designed of Industrial, Commercial and Domestic door and gate applications where a safety edge is used. The system provides a wireless system replacing

More information

Instruction manual. art Installation manual

Instruction manual. art Installation manual Instruction manual art. 01521 Installation manual Contents GENERAL FEATURES AND FUNCTIONALITY from page 4 ETS PARAMETERS AND COMMUNICATION OBJECTS from page 6 COMMUNICATION OBJECTS GENERAL FEATURES AND

More information

Room Temperature Controllers. for heating and cooling systems

Room Temperature Controllers. for heating and cooling systems 3 048 RCU15 Room Temperature Controllers for heating and cooling systems RCU15 Choice of two-position or modulating PI control ON / OFF or PWM outputs for heating and cooling Control depending on room-

More information

R PROFLAME Instruction Book Collection

R PROFLAME Instruction Book Collection 9.956.028 R00 584 PROFLAME Instruction Book Collection 4-17 18-29 584 PROFLAME System 30-39 Appendix: DIP SWITCH NUMBER (0=ON 1=OFF) 40-41 4-17 Fig. 1 The SIT is a device that allows, in conjunction with

More information

Self-learning Room Temperature Controller Receiver

Self-learning Room Temperature Controller Receiver 2 265 REV23RF REV-R.02/1 REV23RF/SE Self-learning Room emperature Controller Receiver Consisting of controller (with integrated radio transmitter) and receiver (switching unit with relay outputs) REV23RF

More information

WLDS-10 Mk2 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING

WLDS-10 Mk2 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING WLDS-10 Mk2 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING DESCRIPTION: An electronic control panel used in conjunction with one pulse meter (a water meter with pulse output proportional

More information

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this fancy 868MHz Temperature Station which displays the time, indoor temperature and indoor humidity,

More information

E N SHT-1 SHT-1/2 SHT-3 SHT-3/2

E N SHT-1 SHT-1/2 SHT-3 SHT-3/2 Digital time switch E N SHT-1 SHT-1/2 SHT-3 SHT-3/2 Content Symbol, Connection... 3 Warning... Characteristics... 5 Technical parameters... 6 Versions of time switches, Load... 7 Description... 8-9 Control...

More information

Weekly Timer. ON/OFF and cycle operations up to one week Two SPST-NO time limit contacts with manual override switches

Weekly Timer. ON/OFF and cycle operations up to one week Two SPST-NO time limit contacts with manual override switches Weekly Timer Timer Provides Prompted Programming, Flexibility in Programs Within the Week AM/PM display 24 program steps A different program possible each day Over midnight settings possible Two independent

More information

Room Temperature Controller

Room Temperature Controller 2 214 REV200.03RF REV200S.03RF REV200RF/SE REV200SRF/SE Room emperature Controller REV-R.03/1 REV-R.03S/1 REV200../SE Backlit touch screen with integrated radio transmitter and receiver (switching unit

More information

CALEFFI. Electronic thermal control system for radiators. 210 series 01263/15 GB. RADIO WAVE system

CALEFFI. Electronic thermal control system for radiators. 210 series 01263/15 GB. RADIO WAVE system Electronic thermal control system for radiators 210 series LEFFI 0126/15 G REDITED ISO 9001 FM 21654 RDIO WVE system Function The radio wave thermal control system is composed of: - multi-zone thermal

More information

Wireless temperature controller E N RFTC-50/G

Wireless temperature controller E N RFTC-50/G Wireless temperature controller E N RFTC-50/G Contents Warning... 3 Characteristics... 4 Technical parameters... 5 Battery replacement... 6 Description of device... 7 Description of display... 8 Description

More information

Connect + compatible

Connect + compatible Connect + compatible Looking for a quick setup up guide? There is lots of useful information in this book, but if all you are after is quick set up look for the following headings in this book 1) Setting

More information

Communicative heating controller

Communicative heating controller UC100 Communicative heating controller Summary UC100 is a communicative room heating controller with one PWM output for control of a radiator or electrical heater. It can work autonomously, or in connection

More information

Radio controllers. Innovation combined with skill and tradition. Intelligent solutions. for all living spaces. Radio-controlled regulation

Radio controllers. Innovation combined with skill and tradition. Intelligent solutions. for all living spaces. Radio-controlled regulation Radio controllers Radio-controlled regulation The radio-controlled temperature regulation of domestic heating systems is ideally suited for both new build and renovation projects. It also offers increased

More information

NRT 105: Electronic fan-coil controller, equiflex

NRT 105: Electronic fan-coil controller, equiflex Product data sheet 4.04 R 105: Electronic fan-coil controller, equiflex How energy efficiency is improved ECO Meter for displaying the current energy consumption and digital input for the change-over between

More information

R-Tronic Climate display device/control

R-Tronic Climate display device/control Valves, controls + systems GB R-Tronic RT B / RTF B / RTFC K Aktor MH CON B / Aktor MD CON B Installation and operating instructions R-Tronic Climate display device/control - 2 von 60 - Extent of supply

More information

PHOENIX CONTACT - 09/2009

PHOENIX CONTACT - 09/2009 Electronic miniature circuit-breaker CLIPLINE Data sheet 03906_en_0 PHOENIX CONTACT - 09/2009 Description The EC-E... electronic miniature circuit-breaker selectively protects all 24 V DC load circuits

More information

Booster amplifier. Table of contents. Features. RE 30260/04.12 Replaces: Type VT-MSFA1. Component series 1X 1/6

Booster amplifier. Table of contents. Features. RE 30260/04.12 Replaces: Type VT-MSFA1. Component series 1X 1/6 Booster amplifier RE 30260/04.12 Replaces: 08.11 1/6 Type VT-MSFA1 Component series 1X H7924 Table of contents Contents Page Features 1 Ordering code 2 Functional description 2 Block diagram / pinout 3

More information

3000W multi Pir light controller

3000W multi Pir light controller 3000W multi Pir light controller Cat No. MLB3000 - Black Cat No. MLW3000 - White Installation & Operating Instructions INSTALLATION & operating instructions SECTION ONE GENERAL INFORMATION The unit utilises

More information

RADIO DRIVER. * _Rev.1* Installation guide. Wireless programmer. RADIO DRIVER zone RADIO DRIVER zones

RADIO DRIVER. * _Rev.1* Installation guide. Wireless programmer. RADIO DRIVER zone RADIO DRIVER zones Installation guide RADIO DRIVER Wireless programmer 6051117 6051118 RADIO DRIVER 610-1 zone RADIO DRIVER 620-2 zones DELTA DORE - Bonnemain - 35270 COMBOURG - FRANCE E-mail: deltadore@deltadore.com 6051119

More information

CS-200. PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL

CS-200. PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL CS-200 PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL CS-200 Operation and Service Manual Page 2 Manufactured by: LINCAST INTERNATIONAL PTY. LTD. 2/3 Sir Laurence Drive

More information

Installation Guide. ECL Comfort 310, application A Table of Contents

Installation Guide. ECL Comfort 310, application A Table of Contents 1.0 Table of Contents 1.0 Table of Contents... 1 1.1 Important safety and product information..................... 2 2.0 Installation... 6 2.1 Before you start.....................................................

More information

WIRELESS 868 MHz WEATHER STATION

WIRELESS 868 MHz WEATHER STATION WIRELESS 868 MHz WEATHER STATION Instructions Manual INTRODUCTION: Congratulations on purchasing this Weather Station with wireless 868 MHz transmission of outdoor temperature and display of indoor temperature,

More information

Room Temperature Controllers. for heating and cooling systems

Room Temperature Controllers. for heating and cooling systems 3 041 RCU10 RCU101 Room Temperature Controllers for heating and cooling systems RCU10 Choice of two-position or modulating PI control ON / OFF or PWM outputs for heating and cooling Operating modes: normal

More information

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this temperature station with wireless 868 MHz transmission of outdoor temperature and display of indoor

More information

Shutter Actuator with Manual Operation, 4-fold, 230 V AC, MDRC JA/S M, GH Q R0111. ABB i-bus EIB / KNX

Shutter Actuator with Manual Operation, 4-fold, 230 V AC, MDRC JA/S M, GH Q R0111. ABB i-bus EIB / KNX , GH Q631 0064 R0111 Technical data 2CDC 071 234 F0003 For controlling 4 independent shutter or sunblind drives, 230 V AC, via ABB i-bus including the functions Up/Down, Step/Stop, Move to position, Sun

More information

RADIOBAND V3 Programming & Installation Manual

RADIOBAND V3 Programming & Installation Manual RADIOBAND V3 Programming & Installation Manual Radioband V3 User s Manual Introduction The RadioBand system is designed for Automatic Gates, Commercial and Domestic door applications where a safety edge

More information

Electronic Circuit Breaker ESS1 for System SVS1

Electronic Circuit Breaker ESS1 for System SVS1 Electronic Circuit Breaker for System SVS Description The electronic circuit breaker is designed to ensure selective disconnection of individual s in industrial systems which are powered by a DC 24 V switch

More information

Control module 2 circuits AD290. Installation and Service Manual

Control module 2 circuits AD290. Installation and Service Manual EN Control module 2 circuits AD290 Installation and Service Manual 129443-02 Contents 1 Introduction...4 1.1 Symbols used...4 1.2 Abbreviations...4 2 Safety instructions and recommendations...5 2.1 Recommendations...5

More information

16-Channel Yearly Time Switch TR 648 S DCF

16-Channel Yearly Time Switch TR 648 S DCF 16-Channel Yearly Time Switch TR 648 S DCF Illustration 1 : TR 648 S DCF TR 648 S DCF EIB 648 9 201 DCF 77 Antenna 907 0 271 Obelisk 2.0 Programming set 907 0 305 Obelisk 2.1 Software 931 0 961 Page 1

More information

X-CORE. Residential Irrigation Controller. Owner s Manual and Programming Instructions RUN SYSTEM OFF CURRENT TIME/DAY MANUAL-ONE STATION START TIMES

X-CORE. Residential Irrigation Controller. Owner s Manual and Programming Instructions RUN SYSTEM OFF CURRENT TIME/DAY MANUAL-ONE STATION START TIMES SYSTEM OFF CURRENT TIME/DAY SEASONAL ADJUSTMENT WATER DAYS X-CORE Residential Irrigation Controller RUN SENSOR BYPASS MANUAL-ONE STATION ACTIVE START TIMES RUN TIMES Owner s Manual and Programming Instructions

More information

KNX radio wall-transmitter 1gang/2gang flat quicklink Order no.: 8565 x2 xx

KNX radio wall-transmitter 1gang/2gang flat quicklink Order no.: 8565 x2 xx KNX radio wall-transmitter 1gang/2gang flat quicklink KNX radio wall-transmitter 1gang/2gang flat quicklink Order no.: 8565 x2 xx KNX radio wall-transmitter 1gang/2gang flat solar quicklink Order no.:

More information

NSD Safety Mat Controller Modules Both Modules are compliant to OSHA & ANSI Standards - EN ISO EN EN 81-1 EN NSD VDC

NSD Safety Mat Controller Modules Both Modules are compliant to OSHA & ANSI Standards - EN ISO EN EN 81-1 EN NSD VDC Datasheet NSD Safety Mat Controller Modules Both Modules are compliant to OSHA & ANSI Standards - EN ISO 13849-1 EN 62061 EN 81-1 EN 50156-1 Approvals NSD-3580 24 VDC NSD-3590 115 TO 230 VAC Technical

More information

Use of the application program. Contents. instabus EIB Application program description. September S2 Room temperature controller

Use of the application program. Contents. instabus EIB Application program description. September S2 Room temperature controller Use of the application program Product family: Product type: Manufacturer: Heating, Air conditioning, Ventilation Thermostat Siemens Name: Room temperature controller IKE 250 DELTA millennium Order no.:

More information

NEW WAVE RICEVITORE RADIO 1 CANALE PER IMPIANTI DI RISCALDAMENTO/RAFFRESCAMENTO

NEW WAVE RICEVITORE RADIO 1 CANALE PER IMPIANTI DI RISCALDAMENTO/RAFFRESCAMENTO NEW WAVE RICEVITORE RADIO 1 CANALE PER IMPIANTI DI RISCALDAMENTO/RAFFRESCAMENTO 1 RADIO CHANNEL RECEIVER FOR HEATING/COOLING SYSTEM 1-KANAL-RADIOEMPFÄNGER FÜR HEIZUNGS-/KÜHLUNGSANLAGEN RÉCEPTEUR RADIO

More information

Awning control system GFM001. Installation and Operating Instructions

Awning control system GFM001. Installation and Operating Instructions Geiger-Funk Sunshade controls Awning control system for 230V drives GFM001 Installation and Operating Instructions for pre-coded systems Table of Contents 1 Introduction...3 2 Safety instructions...3 3

More information

Expandable Controller 3, 7, 11, 15 stations Installation and Programming Guide

Expandable Controller 3, 7, 11, 15 stations Installation and Programming Guide seconds. This blinking cycle is to go on until the low battery condition is corrected. At that time the normal display returns. Also, while LO BA is blinking, if the dial is turned or any button is pressed,

More information

RF (RADIO FREQUENCY) WIRELESS PENDANT

RF (RADIO FREQUENCY) WIRELESS PENDANT NOTE: The following information is an addition to the Operation section in the lift system owner s manual. It describes the RF wireless pendant for your lift system. You must read the lift system owner

More information

OWNERS MANUAL FOR STERLING SERIES CONTROLLERS

OWNERS MANUAL FOR STERLING SERIES CONTROLLERS OWNERS MANUAL FOR STERLING SERIES CONTROLLERS 24950 AVENUE KEARNY, VALENCIA, CALIFORNIA 91355-2142 PHONE (661) 257-3533 FAX (661) 257-9472 TABLE OF CONTENTS Selecting the Location for the Controller...3

More information

1. Contents Page. 2. Assembly, putting into operation, connection Control elements Display Factory setting Changing settings 6

1. Contents Page. 2. Assembly, putting into operation, connection Control elements Display Factory setting Changing settings 6 1. Contents 2 1. Contents Page 2. Assembly, putting into operation, connection 3 3. Control elements 4 4. Display 4 5. Factory setting 5 6. Changing settings 6 6.1 Time and day of the week 6 6.2 Calendar

More information

Q 3007 Biometric Transponder

Q 3007 Biometric Transponder State of: June 2006 Content 1.0 General Instructions 3 1.1 Safety instructions 3 1.2 Product description 3 2.0 Overview of function 4 2.1 Basic information on operation 4 2.2 Operating states 4 2.3 How

More information

EMD-FL-3V-400. Electronic monitoring relay for voltage monitoring in three-phase networks. INTERFACE Data sheet _en_03. 1 Description.

EMD-FL-3V-400. Electronic monitoring relay for voltage monitoring in three-phase networks. INTERFACE Data sheet _en_03. 1 Description. Electronic monitoring relay for voltage monitoring in three-phase networks INTERFACE Data sheet 102110_en_03 1 Description PHOENIX CONTACT - 09/2009 Features Increasingly higher demands are being placed

More information

EC5401B. B-Tronic EasyControl. Assembly and Operating Instructions. Wall/hand-held transmitter, 1-channel, bidirectional

EC5401B. B-Tronic EasyControl. Assembly and Operating Instructions. Wall/hand-held transmitter, 1-channel, bidirectional B-Tronic EasyControl EC5401B en Assembly and Operating Instructions Wall/hand-held transmitter, 1-channel, bidirectional Important information for: Fitters / Electricians / Users Please forward accordingly!

More information

STEP-UPS/24DC/24DC/3. Uninterruptible power supply. Data sheet. 1 Description. Features

STEP-UPS/24DC/24DC/3. Uninterruptible power supply. Data sheet. 1 Description. Features Uninterruptible power supply Data sheet 105623_en_00 PHOENIX CTACT 2013-06-07 1 Description Uninterruptible power supply units continue to deliver power even in the event of mains breakdowns or failures.

More information

Manual. Radio Control Central Unit

Manual. Radio Control Central Unit Manual Radio Control Central Unit 0358 18 825 324 52 05.2004 Controls and connectors (1) Display with 7 lines (2) 4 function keys (soft-keys) (3) 12 keys (keypad) (4) Chip-card reader (5) Main connection

More information

Network VP TM Satellite User s Guide

Network VP TM Satellite User s Guide Network VP TM 2.00 Satellite User s Guide 16 to 64 stations in eight-station increments Field programmable for future upgrades Does not require EPROM(s) replacement Operates as a stand-alone controller

More information

Electronic Circuit Breaker ESS1 for System SVS1

Electronic Circuit Breaker ESS1 for System SVS1 Electronic Circuit Breaker for System SVS Description The electronic circuit breaker is designed to ensure selective disconnection of individual s in industrial systems which are powered by a DC 24 V switch

More information

R9999 ROBERTS. PLL Synthesised 3 band radio with station name display. Sound for Generations. Please read this manual before use

R9999 ROBERTS. PLL Synthesised 3 band radio with station name display. Sound for Generations. Please read this manual before use ROBERTS Sound for Generations R9999 PLL Synthesised 3 band radio with station name display Please read this manual before use Contents Important Information... 1 Automatic plug and play setup... 2 Controls...

More information

BossDim RS. User manual - UK

BossDim RS. User manual - UK BossDim RS User manual - UK Congratulations on acquiring your new BossDim RS We are happy you have chosen our product to control your home lighting, and we hope it gives you hours of pleasure. On the following

More information

KNX TH65-AP. Thermo-Hygrometer. Installation and Adjustment. Item number 70184

KNX TH65-AP. Thermo-Hygrometer. Installation and Adjustment. Item number 70184 EN KNX TH65-AP Thermo-Hygrometer Item number 70184 Installation and Adjustment 1 Content 1. Description... 3 1.1. Technical specifications... 3 2. Installation and commissioning... 4 2.1. Installation

More information

Wireless Rain and Wireless Rain/Freeze Sensor

Wireless Rain and Wireless Rain/Freeze Sensor Wireless Rain and Wireless Rain/Freeze Sensor Installation and Operating Instructions for: WRC: Wireless Rain Sensor Combo WRT: Wireless Rain Sensor Transmitter WSR: Wireless Rain Sensor Receiver WRFC:

More information

Circuit diagram. Applications. Function. Function (Continued) Page 23 SNO 4062K /K-A /KM /KM-A

Circuit diagram. Applications. Function. Function (Continued) Page 23 SNO 4062K /K-A /KM /KM-A SNO 4062K Basic unit for emergency stop and guard door applications Basic unit as per DIN EN 60204-1 and EN ISO 13849-1 for single or twin channel emergency stop monitoring. PL e and category 4 as per

More information

433 MHZ TEMPERATURE STATION Instruction Manual

433 MHZ TEMPERATURE STATION Instruction Manual 433 MHZ TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this innovative 433MHz Temperature Station which displays the time with up to the minute indoor and up to three

More information

Electronic Circuit Breaker ESS20-0..

Electronic Circuit Breaker ESS20-0.. Description Electronic circuit breaker type ES-0.. is designed to ensure selective disconnection of individual loads in systems which are powered by a DC 4 V switch-mode power supply. DC 4 V power supplies,

More information

3301 INSTALLATION AND OPERATING INSTRUCTIONS

3301 INSTALLATION AND OPERATING INSTRUCTIONS DOWN Cover Closed MODE UP Cover Open DOWN MODE TIMER TIME SET UP 3301 INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION This SKYTECH remote control system was developed to provide a safe, reliable,

More information

R9939 ROBERTS. PLL Synthesised 3 band mains battery radio. Sound for Generations. Please read this manual before use

R9939 ROBERTS. PLL Synthesised 3 band mains battery radio. Sound for Generations. Please read this manual before use ROBERTS Sound for Generations R999 PLL Synthesised band mains battery radio Please read this manual before use Contents Important Information... 1 Automatic FM setup... 2 Controls... - Display... Battery

More information

Dipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str Grünberg Tel.: Fax:

Dipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str Grünberg Tel.: Fax: Dipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str. 65 35305 Grünberg Tel.: 06401 807-0 Fax: 06401 807-259 Insulation fault locator Insulation fault locator for DC IT systems with high system leakage capacitances

More information

KNX Powerline PL 110. KNX Association

KNX Powerline PL 110. KNX Association KNX Powerline PL 110 Table of Contents 1 Introduction...3 2 Standardisation...3 3 Transmission Process...4 3.1 Phase Coupling...5 3.2 Telegram Transmission...6 3.2.1 Training Sequence...6 3.2.2 Preamble

More information

433 MHZ REMOTE THERMO

433 MHZ REMOTE THERMO 433 MHZ REMOTE THERMO INTRODUCTION: Congratulations on purchasing this innovative 433MHz Remote Thermo which displays the time with up to the minute indoor and up to five outdoor temperature readings.

More information

Electronic Circuit Breaker with reset input ESS20-1..

Electronic Circuit Breaker with reset input ESS20-1.. Electronic Circuit Breaker with reset input ESS0-.. Description The special device ESS0-.. is a further extension of the product line electronic circuit breakers. Type ESS0-.. has a width of only. mm and

More information