General Specifications

Transcription

1 General Specifications View Recorder Wide-View Model VR00 GS NA-E OVERVIEW The VR00 is a PAPER-LESS recorder that displays realtime measured data on a color LCD and saves data on a.5-inch floppy disk. It comes with a two, four-channel or six-channel model. As the input signal, a DC voltage, thermocouple, resistance temperature detector, or contact signal can be set to each channel. The data saved on a floppy disk can be converted by data conversion software to Lotus --, Excel, or ASCII format file, facilitating processing on a PC. Not only this, the Viewer software allows a PC to display waveforms on its screen and to print out waveforms. STANDARD SPECIFICATIONS General Specifications Construction Mounting Flush panel mounting (on a vertical plane) Mounting may be inclined downward up to 0 from a horizontal plane. Allowable Panel Thickness: to 6 mm Material: Case: drawn steel Bezel: polycarbonate Case Color: Lamp black (Munsell 0.8Y.5/0. or equivalent) Dimensions: (W) (H) 80(D) mm Weight: VR0, 0; approx..9 kgf VR06 ; approx..8 kgf Input Number of Inputs: VR0; up to two channels (selectable in channels or ) VR0; up to four channels (settable in channels to ) VR06; up to six channels (settable in channels to and 6) Measurement Interval: VR0, 0;5 ms VR06; s ( s when an A/D integration time is set to 00 ms) Inputs: DCV (DC voltage), TC (thermocouple), RTD (resistance temperature detector), DI (digital input for event recording), DCA (DC current with external shunt resistor attached) Input type DC voltage (DCV) Thermocouple (TC) Resistance temperature detector (RTD) (measurement current i=0.5ma) Event recording (DI) Range 0mV 60mV 00mV V 6V 0V R * S * B * K * E * J * T * N * W * L * U * Pt00 *5 JPt00 *5 DCV input Contact input F00.EPS Measuring range to 0.00 mv to mv to 00.0 mv to.000 V to 6.000V V to 0.00 V 0.0 to C 0.0 to C 0.0 to 80.0 C to 70.0 C to C to 00.0 C to 00.0 C 0.0 to 00.0 C 0.0 to 5.0 C to C to 00.0 C to C to C Less than. V: off;. V or greater: on Contact on/off * R, S, B, K, E, J, T: ANSI, IEC 58, DIN IEC 58, JIS C * N: Nicrosil-Nisil, IEC 58, DIN IEC 58 * W: W 5%Re-W 6%Re (Hoskins Mfg. Co.) * L: Fe-CuNi, DIN70 U: Cu-CuNi, DIN70 *5 Pt00: JIS C , JIS C , IEC 75, DIN IEC 75 JPt00: JIS C 60-98, JIS C T0.EPS GS NA-E Copyright Jan. 997(YG) 7th Edition Aug. 998(YG)

2 A/D Integration Time: Fixed to 0 ms (50 Hz) or 6.7 ms (60 Hz) 00ms (50/ 60Hz for VR06), or AUTO selectable (automatic selection by detection of power supply frequency) Thermocouple Burnout: Burnout upscale/downscale function can be switched on/ off (common for all channels). Burnout upscale/downscale selectable Filter: VR0, 0; On/off selectable (common for all channels) Time constant: selectable from, 5, and 0 seconds VR06; moving average on/off selectable (common to all channels), moving average cycles to 6 selectable Calculation: Differential computation: Between any two channels; however, reference channel must be smaller than measuring channel number. Available for DCV, TC, and RTD ranges. Linear scaling: Available for DCV, TC, and RTD ranges. Scaling limits: to 0000 Decimal point: user-selectable Engineering unit:user-definable, up to 6 characters Square root: Available for DCV range. Scaling limits: to 0000 Decimal point: user-selectable Engineering unit:user-definable, up to 6 characters Display Display unit: 5.5-inch TFT color LCD (0 0 pixels) Analog display: waveform display direction is user-selectable from vertical and horizontal. Line width of waveforms are user-selectable from,, and pixels. Analog display color: VR0; Red for channel, green for channel (These colors as well as blue, violet, brown, cyan, orange and gray are user-selectable for each channel.) VR0; Red for channel, green for channel, blue for channel, violet for channel (These colors as well as brown, cyan, orange and gray are user-selectable for each channel.) VR06; Red for channel, green for channel, blue for channel, violet for channel, orange for channel 5, cyan for channel 6 (These colors as well as brown and gray are user-selectable for each channel.) Waveform span rate: User-selectable from, 5, 0, 0, 0, and 60 min/div Digital indication: Measured values (updated every second), alarm types, engineering units (up to 6 characters), and tags (up to seven characters) Memory status display: The memory status of the event file is displayed when storing data in the event file in the trigger mode. The remaining sampling time of the display data file is displayed (from 99 before overwriting). Other display contents: Scale values, (0 and 00%, display on/off selectable), grid lines (number of divisions selectable from to ), hour:minute on grid, trip levels (line widths are selectable from, and pixels), messages (up to five different messages of up to 6 characters for each, displayed only in the vertical waveform display mode), alarms (ALM), waveform span rate Data referencing function: By splitting the waveform display area into two, current waveforms and reference waveforms can be compared on the display. Min/max digital values are displayed as reference values. Display magnification/reduction function: The time scale of analog display can be magnified and reduced. Bargraph display: The measured values are displayed as easy-toread bar graphs. The channel or tag number, alarm status, unit, scale values, and alarm settings of each channel are displayed together. Large digital display: The measured values are displayed as large digits. The alarm status and unit of each channel are displayed together. Alarm summary display: Up to the fifty most recent alarm events occurrences and recoveries of alarms are displayed. The number of samples stored in each of the display data and event files and the percentage of memory currently used are also displayed. LCD saver function: The LCD backlight automatically dims if no key is touched for a certain preset time (can be set from, 5, 0, 0, 0 and 60 minutes). Data Saving Function External storage medium:.5-inch floppy disk (HD) (The formatting can be. (for VR0, 0 only) or. MB.) Saving method: Transmitting of data from internal memory to floppy disk Data Saving Period: Linked with the sampling (for the event file) specified or the waveform span rate (for a display data file) Event File Period: VR0, 0; Selectable from 5 ms, 50 ms, 500 ms, and s. VR06; Selectable from,, 0, 0, 60, and 0s. All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

3 File: The following two file types can be created. Event file (stores instantaneous values sampled ically at a specified sampling rate) Display data file (stores the maximum and minimum values for each waveform span rate from among measured data sampled at measurement intervals) Files can be created in the following combinations. (a) Event file + display data file (b) Event file 6 + display data file (c) Event file only : For VR0: double the sampling time of VR0. For VR0 In case (a) above, Display data file (when using full four channels) Waveform span rate (min/div) * min 6 5 min 5 days 0 min days 0 min days 0 min days 60 min 66 days Event file (when using full four channels) Amount of data: 0,000 points/channel * 5 ms 50 ms 500 ms s * hour.. 8. In case (b) above, The sampling times for the display data file are the same as those in case (a). Event file (one of sixteen for four channel inputs) Amount of data:,000 points/channel * * 5 ms. min Amount of data: 8,000 points/channel * 50 ms 8. min 500 ms 6.6 min s min In case (c) above, Event file (for four channel inputs) Amount of data:,000 points/channel * 5 ms 50 ms 500 ms s * T0.EPS For VR06 In case (a) above: Display data file (when using all six channels) Amount of data: 7,600 points/channel * Waveform span min 5 min 0 min 0 min 0 min 60 min rate (min/div) * 6 5 days days days days 66 days Event file (when using all six channels) Amount of data: 0,000 points/channel * s s 0 s 0 s 60 s 0 s * 5.5 days 6 days days 7 days T0.EPS * The sampling time varies depending on the channel settings * The amounts of these data are approximate. In case (b) above: The display data files are the same as those in case (a). Event file (one of sixteen for six channel inputs) Amount of data:,00 points/channel * * s min In case (c) above: Event file (for all six channels) * s s min 0 s 0 s 60 s 0 s Amount of data:,000 points/channel * s days 0 s 0 s 60 s 0 s days 8 days 77 days 55 days T0.EPS Other files: Setup parameter file (setup parameter list), information file (event, power-failure, and alarm information) Event information: When the event is occurred, the data no. of the display data (or event) file and date/time of occurrence are saved (max. times). Power-failure information: When a power-failure is occurred, the data no. and date/time of occurrence/ recovery are saved (max. 0 times). Alarm information: When a alarm is occurred, the alarm channel no., alarm type/level and date/time of alarm occurrence/recovery are saved (max. 50 times). Data format: Measured data: Binary in Yokogawa standard format ( bytes/data value) Setup parameters and event, power-failure, alarm information: ASCII format Trigger function: An external contact, key on the recorder panel, or an alarm can be assigned as the trigger to start saving data in an event file. A pre-trigger function is available. (The trigger point is set in increments of 0% of the memory length.) Behavior when the memory is full: Event file: In the FREE sampling mode: The oldest data are overwritten. In the TRIG sampling mode: The next trigger is neglected and stored data are retained. In the ROTATE sampling mode: When the next trigger is raised, the contents of the file (the oldest file when sixteen files have been created) is cleared and storage of the new data begins. Display data file: The oldest data are overwritten. Setting data memory: Setting data (SET mode, SET-UP mode) can be stored on a FD, and it can be retrieved. All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

4 Alarm Function Number of alarm levels: Up to four levels for each channel Alarm types: High and low limits, differential high and low limits, and high and low rate-of-change limits Interval time of rate-of-change alarms: The measurement interval times to 5 Display: The alarm status (type) is displayed in the digital value display area upon occurrence of an alarm. A common alarm indication is also displayed. The alarming behavior: non-hold- or hold-type can be selectable for common to all channels. Hysteresis: On (0.5% of span)/off switchable (common to all channels and alarm levels) Outputs:,, or 6 points (optional). On-energized/on-deenergized and hold/non-hold selectable. Memory: The times of alarm occurrences/recoveries, alarm types, etc. are stored in the memory. (Up to fifty alarm events per channel are stored.) Power Supply Rated power supply: 00 to 0 V AC (automatic switching) Allowable power supply voltage range: 90 to or 80 to 50 V AC Rated power supply frequency: 50/60 Hz (automatic switching) Power consumption: For VR0 / VR0 / VR06 Supply voltage 00 V AC 0 V AC LCD saver mode 5 VA 5 VA Normal 0 VA 0 VA () Max. 60 VA 70 VA T05.EPS Other Specifications Clock: With calendar function (Western calendar) The time can be adjusted by a remote contact (with the Remote option). Accuracy of clock: ±00 ppm, excluding a delay (of second, maximum) caused each time the power is turned on/off. Memory backup: The setup parameters are backed up by a built-in lithium battery (battery life: approximately ten years at room temperature). The measured values are stored in the flash memory, and thus there are no limitations to the backup time. Insulation resistance: Each terminal to ground terminal: 0 MΩ or greater (at 500 V DC) Dielectric strength: Power supply to ground terminal: 500 V AC (50/60 Hz), minute Contact output terminal to ground terminal: 500 V AC (50/60 Hz), minute Measuring input terminal to ground terminal: 000 V AC (50/60 Hz), minute Between measuring input terminals: 000 V AC (50/60 Hz), minute (except for RTD of VR06, since b-terminal is common). Between remote control terminal to ground terminal: 500 V DC, minute Safety and EMC Standards Safety standards: Certified by CSA.No. 00. Complies with EN600- EMI standards: Complies with EN550 Group Class A Immunity: Complies with EN5008- Normal Operating Conditions Power voltage: 90 to or 80 to 50 V AC Power supply frequency: 50 Hz ±%, 60 Hz ±% Ambient temperature: 0 to 50 C (when using FDD: 5 to 0 C) Ambient humidity: 0% to 80%RH (at 5 to 0 C) Vibration: 0 to 60 Hz, 0. m/s or less Shock: Not acceptable Magnetic field: 00 AT/m or less (DC and 50/60 Hz) Noise: Normal mode (50/60 Hz) DCV The peak value including the signal must be less than. times the measuring range. TC The peak value including the signal must be less than. times the measuring thermal electromotive force. RTD 50 mv or less Common mode (50/60 Hz) 50 Vrms AC or less for all ranges Maximum noise voltage between channels (50/60 Hz) 50 Vrms AC or less Mounting position: Can be inclined up to 0 backward. Mounting at an angle away from the perpendicular is not acceptable. Warm-up time: At least 0 minutes after power on All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

5 5 Standard Performance Measuring and Recording Accuracy: The following specifications apply to operation of the recorder under standard operation conditions: temperature at ± C; humidity of 55%±0%RH; power supply voltage of 90 to or 80 to 50 V AC; power supply frequency of 50/60 Hz ±%; and warm-up time of at least 0 minutes. Other ambient conditions such as vibration should not adversely affect recorder operation. Input Range Measurement Accuracy (Digital Display) Max. Resolution of Digital Display DCV 0 mv 60 mv 00 mv V ±(0.% of rdg + digits) ±(0.% of rdg + digits) ±(0.% of rdg + digits) ±(0.% of rdg + digits) 0 µv 0 µv 00 µv mv 6 V ±(0.% of rdg + digits) mv 0 V ±(0.% of rdg + digits) 0 mv TC (excluding the reference junction compensation accuracy) R S B K E J T ±(0.5% of rdg + C) However, R, S: ±.7 C at 0 to 00 C ±.5 C at 00 to 00 C B: ± C at 00 to 600 C accuracy at less than 00 C is not guaranteed ±(0.5% of rdg C) However, (0.5% of rdg + C) at -00 to -00 C ±(0.5% of rdg C) ±(0.5% of rdg C) However, ±(0.5% of rdg C) at -00 to -00 C 0. C N ±(0.5% of rdg C) W ±(0.5% of rdg + C) L ±(0.5% of rdg C) RTD U Pt00 JPt00 However, ±(0.5% of rdg C) at -00 to -00 C ±(0.5% of rdg + 0. C) T06.EPS Maximum resolution of analog display: Waveform display: When the direction of waveform display is vertical: 65 0 pixels (57 mm) When the direction of waveform display is horizontal: 00 0 pixels (70 8 mm) Pixel pitch: 0.8 (vertical) mm 0.8 (horizontal) mm Measurement accuracy in case of scaling (digits) = measurement accuracy (digits) scaling span (digits) measurement span (digits) + digits F0.EPS Decimals are rounded off to the next highest number. Reference junction compensation: INT (internal)/ext (external) selectable (common for all channels) Reference junction compensation accuracy (above 0 C): Types R, S, B, W: ± C Types K, J, E, T, N, L, U: ±0.5 C Maximum allowable input voltage: ±0 V DC (continuous) for less than V DC ranges and TC ranges ±0 V DC (continuous) for 6V and 0V ranges Input resistance: Approximately 0 MΩ or more for DCV ranges of V or less and TC Approximately MΩ for 6V and 0V DCV ranges Input source resistance: DCV, TC: RTD: kω or less 0 Ω or less per wire (The resistance of all three wires must be equal.) Input bias current: 0 na or less (approximately 00 na when the burnout upscale/downscale function is switched on) Maximum common mode voltage: 50 Vrms AC (50/60 Hz) All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

6 Maximum noise voltage between channels: 50 Vrms AC (50/60 Hz) Interference between channels: 0 db (when the input source resistance is 500 Ω and the inputs to other channels are 0 V) Common mode rejection ratio: 0 db (50/60 Hz ±0.%, 500 Ω imbalance between the minus terminal and ground) Normal mode rejection ratio: 0 db (50/60 Hz ±0.%) Effects of Operating Conditions Ambient temperature: with temperature variation of 0 C: Digital indication: ±(0.% of rdg + digit) or less excluding the error of reference junction compensation Power supply: with variation within 90 to V and 80 to 50 V AC (50/60 Hz): Digital indication: ± digit or less with variation of ± Hz from rated power frequency (at 00 V AC): Digital indication: ±(0.% of rdg + digit) or less Magnetic field: AC (50/60 Hz) and DC 00 A/m fields: Digital indication: ±(0.% of rdg + 0 digits) or less Input source resistance: () DCV range with variation of + kω: Ranges of V or less:within ±0 µv Ranges of 6V or greater:-0.% of rdg or less () TC range with variation of + kω: Within ±0 µv (±00 µv when the burnout upscale/downscale function is switched on) () RTD range with variation of 0Ω per wire (resistance of all three wires must be equal): Digital indication: ±(0.% of rdg + digit) or less with maximum difference of 0 mω between wires: Digital indication: approximately ±0. C Mounting position: with variation in inclination of ±0% backward Digital indication: ±(0.% of rdg + digit) or less Vibration: when sine-wave motion of frequency of 0 to 60 Hz and acceleration of 0. m/s is applied to the recorder in the directions of three axes for two : Digital indication: ±(0.% of rdg + digit) or less Transport and Storage Conditions The following specifies the environmental conditions required during transportation from shipment to the start of service and during storage as well as during transportation and storage if this instrument is temporarily taken out of service. No malfunction will occur under these conditions without serious damage which is absolutely impossible to repair; however, calibration may be necessary to recover normal operation performance. Ambient temperature: -5 to 60 C Humidity: 5% to 95%RH (No condensation is allowed.) Vibration: 0 to 60 Hz,.9 m/s maximum Shock: 9 m/s maximum (while being packed) SPECIFICATIONS OF OPTIONAL FUNCTIONS Alarm Output Relays (/A, /A, /A) An alarm signal is output from the rear panel as a relay contact signal. Relay contact rating: 50 V DC/0. A (for resistance load) 50 V AC (50/60 Hz)/ A Terminal configuration: SPDT (NO-C-NC) (Energized-at-alarm/deenergized-at-alarm, AND/OR, and hold/non-hold actions are selectable.) RS-A Communication Interface (/C) This interface allows the host computer to control and make settings for the recorder as well as receive data from the recorder. Synchronization method: Start-stop asynchronous transmission Communication level: Conforming to EIA RS-A standard Connection method: -wire half-duplex multi-drop connection (:N where N = to 6) Transmission speed: 00, 00, 800, or 9600 bps Data length: 7 or 8 bits Stop bit: or bits Parity: Odd, even, or none Communication distance: Up to 500 m Communication mode: ASCII for input/output for control and setting ASCII or binary for output of measured data 6 All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

7 (a) Event file + display data file Display data file (when using all four channels) Waveform span rate (min/div) Waveform span rate (min/div) min days min min 6 days Event file (for four channel inputs) 5 ms. 5 min 5 days 0 min 0 min 0 min 60 min days 66 days 00 days 00 days 50 ms 6. 0 min 500 ms. 0 min 0 min s 5 Display data file (when using all four input channels and four computed-value channels) 60 min days days days 66 days deg F Display (/D) Uses deg F as the temperature unit. Large memory (/E) Expands the internal memory size. when using large memory option: -VR0- -VR06- (a) Event file + display data file Display data file (when using all six channels) Waveform span rate (min/div) min days 5 min 6 days Event file (for six channel inputs) Waveform span rate (min/div) s min 6. s 5 min 5 days 0 min 0 min 0 min 7 60 min days 66 days 99 days 98days 0s 0 min 0 s 0 min 60 s days 0 days days 8 days Display data file (when using all six input channels and six computed-value channels) min 60 min days days days 66 days days 6 days 0 s Event file (for six channel inputs and six computed-value channels) s s 0s 0 s 60 s 0 s days 7 days Event file (for four channel inputs and four computed-value channels) (b) Event file only Event file (for six channel inputs) 50 ms 500 ms s s s 0s 0 s 60 s 0 s. (b) Event file only Event file (for four channel inputs) 5 ms.5 50 ms ms days Event file (for four channel inputs and four computed-value channels) 50 ms ms 6.6 s. s days T06-.EPS days s. 7 days s days 8 days 6 days days 66 days Event file (for six channel inputs and six computed-value channels) 0s 0 s 60 s 0 s days 8 days 77 days 55 days T06-.EPS Fail/Memory End Output (/F) The relay contact output on the rear panel indicates the occurrence of a system error and the time specified until end of memory (selectable from,, 5, 0, 0, 50, 00 ) before the data in a continuously storing file are overwritten. Relay contact rating: 50 V DC/0. A (for resistance load) 50 V AC (50/60 Hz)/ A Clamped Input Terminal (/H) used clamped input terminals as input terminal. Desk Top Type (/H5 *) Provides carrying handle and power cord. Weight: VR0, 0/H5 : approx.. kgf VR06/H5 : approx.. kgf * /H5 D: Power cord UL, CSA st'd F: Power cord VDE st'd R: Power cord SAA st'd J: Power cord BS st'd F0.EPS All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

8 French/German display, Summer/Winter time (/L) French or German display can be selected. Summer andwinter time can be set. Mathematical functions (/M and /M) Used for calculating data, displaying trends and digital values, and recording calculated data assigned to channels. The data of each channel, regardless of whether a measured value or calculated value is assigned to it, can be saved as binary data at set intervals ( minute to ). Channels assignable to calculated data: Up to channels for - or -channel model Up to 6 channels for 6-channel model Operations: General arithmetic operations: four arithmetic operations, square root, absolute, common logarithm, exponential, relational operations(>, <, =, ), logic operations(and, OR, NOT, XOR) Statistical operations: average, maximum, minimum, and total of time-series data Constant: Available Note: Measurement interval of the VR0/0 will be 50ms when using calculation channels. Note: To view the calculated data on a personal computer, VA00-0 (VR data viewer for Windows 95) is required when using calculation channels: - VR0 - (a) Event file + display data file Display data file (for two channel inputs) Number of calc. ch Waveform span rate (min/div) min 5 min 0 min 0 min 0 min 60 min days days days days 66 days days 7 days days days days days 5 days days 6 days days days days 8 days days 6 days (b) Event file 6 + display data file The sampling times for the display data file are the same as those in case (a). Event file (one of sixteen for two channel inputs) Number of calc. ch (c) Event file only Event file (for two channel inputs) Number of calc. ch 50 ms 500 ms sec min 6 min min 5.5 min min min. min 8. min 6 min. min 6. min min T09.EPS 50 ms 500 ms sec T0.EPS - VR0 - (a) Event file + display data file Display data file (for four channel inputs) Number of calc. ch Waveform span rate (min/div) min 5 min 0 min 0 min 0 min 60 min days 7 days days days days days 5 days days 6 days days days days 8 days days 6 days day days 7 days days days T.EPS Event file Number 50 ms 500 ms sec. of calc. ch min min. 9 min.6. T07.EPS T08.EPS Event file Number of calc. ch 50 ms 500 ms sec. 8 min min. 9 min.6. 0 min..6 T.EPS All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

9 (b) Event file 6 + display data file The sampling times for the display data file are the same as those in case (a). Event file (one of sixteen for four channel inputs) Number of calc. ch (c) Event file only Event file (for four channel inputs) Number of calc. ch 50 ms 500 ms sec. 5.5 min min min. min 8. min 6 min. min 6. min min.7 min 5. min 0 min T.EPS 50 ms 500 ms sec min T.EPS - VR06 - (a) Event file + display data file Display data file (for six channel inputs) Number of calc. ch Waveform span rate (min/div) min 5 min 0 min 0 min 0 min 60 min 8 days 7 days 5 days days 5 days. days 6 days days 8 days 6 days days 5 days 0 days 5 days 0 days 0. days days 8 days days 5 days days 6 days 0 days 0 days T5.EPS Event file Number of calc. ch 6 9 sec. sec. 0 sec. 0 sec. 60 sec. 0 sec days 0 days 0 days days 8 days 6 days 7 days 6 days days days 5 days days 8 days days 9 days T6.EPS (b) Event file 6 + display data file The sampling times for the display data file are the same as those in case (a). Event file (one of sixteen for six channel inputs) Number of calc. ch 6 sec. sec. 0 sec. 0 sec. 60 sec. 0 sec. 6 min min.7 min 6 min. 0 min min.8 9. min 8 min.5 7 min min. (c) Event file only Event file (for six channel inputs) Number of calc. ch T7.EPS sec. sec. 0 sec. 0 sec. 60 sec. 0 sec days 6 days 5 days 07 days 7 days days days 86 days 8 5 days 7 days 5 days 7 days day 5 days 5 days 0 days 6 days 9 days days days 7 days T8.EPS All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

10 Cu0, Cu5 RTD Input (/N) This option allows Cu0 and Cu5 inputs to be added to the standard input types. Measuring Range of Cu0 and Cu5 Inputs RTD (measurement current i =.5 ma) Measurement Accuracy Measuring Input Type Range Cu0 (GE): α = at 5 C Cu0 (L&N): α = at 5 C Cu0 (WEED): α = at 5 C Cu0 (BAILEY): non-linear -00 to 00 C Cu0: α = at 0 C Cu0: α = at 0 C Cu5: α = at 0 C Input Type Cu0 (GE): α = at 5 C Cu0 (L&N): α = at 5 C Cu0 (WEED): α = at 5 C ±(0.% of rdg +.0 C) Cu0 (BAILEY): non-linear Cu0: α = at 0 C Cu0: α = at 0 C Cu5: α = at 0 C ±(0.% of rdg C) T9.EPS Measurement Accuracy T0.EPS VDC Power Supply (/P) Rated power supply : VDC Allowable power supply voltage range :.6 to 6.VDC Power Consumption: Supply Voltage VDC LCD server mode 5VA Normal 0VA () Max. 50VA T.EPS Remote Control (/R) This option allows the following five functions to be controlled remotely by a contact input: Trigger for event file(trigger, 50ms or longer) Time adjustment (adjusting the time to a preset time upon contact signal, trigger, 50ms or longer) Time of Trigger-on hh:00:00 to hh:0:59 Processing Cut off reading of less than one minute. E.g., 0:00:50 is corrected as 0:00:00. Round up reading of less than one minute. hh:58:00 to hh:59:59 E.g., 0:59:50 is corrected as :00:00. hh:0:00 to hh:57:59 No processing is to be performed. T.EPS Start/stop of computation*(level) Clearance of computation data*(trigger, 50ms or longer) Message display (Up to five different messages can be set, trigger, 50ms or longer) * When the optional mathematical functions (/M or /M) are equipped. APPLICATION SOFTWARE (ACCESSORIES) 0 VR00 application software package File conversion software Operating environment PC: IBM PC-AT compatible models Memory: 60KB or more (free area of at least 00KB) OS: MS-DOS Ver.5.0 or later Disk:.5-inch FD (.MB format) File conversion/data viewer software Operating environment PC: A personal computer that can run MS- Windows Ver.. CPU: 8086SX or later Memory: 8MB or more OS: MS-Windows Ver.. Disk:.5-inch FD (.MB format) Hard disk (free area of at least MB) CRT: Compatible with MS-Windows Ver.. (6colors or higher recommended) Printer: A printer and printer driver compatible with MS-Windows Ver.. VR enhanced application software Operating environment PC: A personal computer that can run MS- Windows Ver.. or Windows95 CPU: 8086DX or later (pentium90 or higher recommended) Memory: 6MB or more OS: MS-Windows Ver.. or Windows95 Disk:.5-inch FD (.MB format) Hard disk (free area of at least MB) CRT: Compatible with MS-Windows Ver.. or Windows95 Can display analog RGB 56 colors or higher (6,000 colors or higher recommended) Printer: A printer and printer driver compatible with MS-Windows Ver.. or Windows95 VR data viewer for windows95 Operating environment PC: A personal computer that can run or Windows95 CPU: 8086DX or later (Pentium0 or higher recommended) Memory: 6MB or more OS: Windows95 Disk:.5-inch FD (.MB format) Hard disk (free area of at least 5MB) CRT: Compatible with Windows95 Can display analog RGB 56 colors or higher (6,000 colors or higher recommended) Printer: A printer and Printer driver compatible with Windows95 All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

11 MS and MS-DOS is a registered trademark of Microsoft Corporation USA. Excel is a registered trademark of Microsoft Corporation USA. Windows is a registered trademark of Microsoft Corporation USA. IBM, IBM PC/AT is a registered trademark of International Business Machines Corp. Lotus -- is a registered trademark of Lotus Development Corporation. Other company and/or product mames is registered trade marks of their manufactures. All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

12 MODEL AND SUFFIX CODES Model Code Suffix Code Option Code Description VR0 VR0 VR06 Application software 0 View Recorder Wide-View Model VR00 (ch) View Recorder Wide-View Model VR00 (ch) View Recorder Wide-View Model VR00 (6ch) No application software with application software package (VP00-0) Options / A / A / A / C / D / E / F / H /H5 / L /M /M / N / P / R Alarm output relay ( points) * Alarm output relay ( points) * Alarm output relay (6 points) * RS--A interface deg F display Large memory FAIL/memory end detection and output * Clamped input terminal Desk top type *, * French/German display, Summer/Winter time Mathematical functions Mathematical functions with VA00-0 (VR data viewer for Windows 95) *5 Cu0, Cu5 RTD input VDC power supply * Remote control * /A, /A, and /A cannot be specified together. * If /F is specified, /A cannot be specified. * /H5 D: Power cord UL, CSA st'd F: Power cord VDE st'd R: Power cord SAA st'd J: Power cord BS st'd * /H5 and /P cannot be specified together. *5 To view the calculated data on a personal computer, VA00-0 (VR data viewer for Windows 95) is required. Model Code Description OS VP00-0 VR00 application software package MS-DOS, Windows. VA00-0 VR enhanced data viewer software Windows., Windows95 VA00-0 VR data viewer for Windows95 Windows95 T.EPS STANDARD ACCESSORIES OPTIONAL ACCESSORIES Item(s) Mounting brackets Fuse Terminal screws Instruction manual Quantity 5 T.EPS Item(s) Shunt resistors (for screw input terminal) Shunt resister (for clamped input terminal, /H) Model (Part) Number Specification 50 Ω ±0.% 00 Ω ±0.% 0 Ω ±0.% 50 Ω ±0.% 00 Ω ±0.% 0 Ω ±0.%.5-inch floppy disks HD (0 disks) Fuse A60EF 50 V 500 ma time lag (except for /P model) A0EF 50 V 5 A time lag (for /P model) Products delivered before July, 998 A5EF 50 V 800 ma time lag (except for /P model) A5EF 50 V 5 A time lag (for /P model) Products delivered after July, 998 Mounting brackets B9900CW T5.EPS All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

13 DIMENSIONS 5.5 (5.96) 0 (5.67) (0.79) (5.67) (5.96) (.0) to 6 (panel thickness) (0.7) 6.5 (5.7) unit : mm (approx. inch) (min. space for mouting) Panel cutout Single-unit Mounting Side-by-side Mounting (horizontally) Side-by-side Mounting (vertically, max. units) (5.9) (5.9) (5.9) L (5.9) 75 MIN (6.89) 7. (0.9) (dimension after mounting) L + 0 Units n L + 0 (mm) ( n)-6 75 MIN (6.89) Note: If not specified, the tolerance is ±%. However, for dimensions less than 0 mm, the tolerance is ±0. mm. F0.EPS All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00

14 Dexk top type Unit:mm (approx. inch) (5.67) 0 (0.79) 7 (9.) 89 (.5) 9 5 (0.59) (5.67).8 (5.6) 0 (.58) Terminal Arrangements Input Terminals /Pmodel + DVV Power supply terminal Screw-on input terminals CH CH CH Option terminal CH CH CH Clamped input terminals (/H) +/A /b CH /B CH /B -/b +/A Input terminal Screw-on input terminals Clamped input terminals (/H) +/A Option Terminals CH CH CH CH CH5 CH6 /b +/A -/B CH CH CH6 /B CH /b CH CH5 /A/C/F/R combination /A/C/F/R combination /A/C/R combination Alarm output relay (/A) Alarm output relay (/A) Alarm output relay (/A) Memory end output FAIL output (/F) Memory end output FAIL output (/F) C SD SD A SG B RD RD A FG B Remote control (/R) Communication (RS-A) (/C) 5 C SD SD A SG B RD RD A FG B Remote control (/R) Communication (RS-A) (/C) 5 C SD SD A SG B RD RD A FG B Remote control (/R) Communication (RS-A) (/C) All Rights Reserved. Copyright 997, Yokogawa Electric Corporation GS NA-E 7th Edition Aug.,998-00