STEVALIPMnM2N. 100 W motor control power board based on STIPN2M50T-H SLLIMM nano IPM MOSFET. Data brief. Features. Description

Transcription

1 STEVAL-IPMnMN Data brief 00 W motor control power board based on STIPNM50T-H SLLIMM nano IPM MOSFET Features Input voltage: from 5 to 00 VDC Nominal power: up to 00 W Nominal current: up to 0.6 Arms Input auxiliary voltage: up to 0 VDC Single- or three-shunt resistors for current sensing (with sensing network) Three options for current sensing: dedicated external op-amps, internal SLLIMM-nano op-amp (single) or via MCU Overcurrent hardware protection IPM temperature monitoring and protection Hall sensor or encoder input Intelligent power module: SLLIMM-nano IPM MOSFET-based (STIPNM50T-H full molded package) Motor control connector ( pins) interfacing with ST MCU boards Universal design for further evaluation with bread board and testing pins Very compact size RoHS compliant Description Product summary Compact motor drive power board STEVALIPMnMN SLLIMM-nano small low-loss intelligent molded module IPM, -phase inverter, A,.7 Ohm max., 500 V MOSFET STIPNM50T-H The STEVAL-IPMnMN is a compact motor drive power board based on SLLIMM nano (small low-loss intelligent molded module) MOSFET-based product (STIPNM50T-H). It provides an affordable and easy-to-use solution for driving high power motors in a wide range of applications such as power white goods, air conditioning, compressors, power fans and -phase inverters for motor drives in general. The IPM itself consists of short-circuit rugged MOSFETs and a wide range of features like undervoltage lockout, smart shutdown, internal temperature sensor and NTC, overcurrent protection and internal op-amp. The main characteristics of this evaluation board are small size, minimal BOM and high efficiency. It features an interface circuit (BUS and VCC connectors), bootstrap capacitors, snubber capacitor, hardware short-circuit protection, fault event signal and temperature monitoring. It is designed to work in single- or three-shunt configuration and with triple current sensing options: three dedicated on-board opamps, op-amps embedded on MCU or single internal IPM op-amp. The Hall/Encoder part completes the circuit. The system is designed to achieve accurate and fast conditioning of current feedback to satisfy the typical requirements for field oriented control (FOC). The STEVAL-IPMnMN is compatible with ST s control board based on STM, providing a complete platform for motor control. DB6 - Rev - May 08 For further information contact your local STMicroelectronics sales office.

2 Figure. STEVAL-IPMnMN circuit schematic ( of 5) DC_bus_voltage I n p u t Bus J R 70K. V INPUT-dc R 70K R 0R D Bus_voltage S T E V A L - I P M N n t m p d e c o d e r G M 0 RC 0 RC 0 0 RC 0 RC 0 RC5 0 RC6 0 RC7 m RC8 0 RC9 0 RC0 0 RC 0 RC N Q p 0 RC R6 k0 UD TSV99. V.65 V C 7 µ/5 V t - STEVAL-IPMnMN C R 7k5 C 0 n 0 RC C 7 µ/5 V R5 k0 DB6 - Rev page /8

3 STEVAL-IPMnMN Figure. STEVAL-IPMnMN circuit schematic ( of 5) E Current_A_amp E Current_B_amp E Current_C_amp SW Current_A SW Current_B SW Current_C EM_STOP PWM-A-H PWM-A-L PWM-B-H PWM-B-L PWM-C-H PWM-C-L NTC_bypass_relay 5 V PWM_Vref M_phase_A M_phase_B Control Connector J Bus_voltage. V NTC M_phase_C Motor Output J phase_c phase_b phase_a DB6 - Rev page /8

4 STEVAL-IPMnMN Figure. STEVAL-IPMnMN circuit schematic ( of 5) 0. W 0. W 0. W STIPNM50T-H DB6 - Rev page /8

5 Figure. STEVAL-IPMnMN circuit schematic ( of 5) E E.65 V.65 V R k0 R0 k9 UA TSV99 R k. V TP. V Current_A_amp.65 V E Current_C_amp nano OP nano OPnano OPOUT. V. V Current_B_amp - C 00 p C8 0 n C0 00 p 5 6 R k9 UB 7 TSV99 C 00 n R k C5 0p R6 k0 R7 k0 TP5 C9 0 p - C 0 n R k0 R k9 TP6 C 0p R5 k9 D0 SW7 R k0 C.7 µ 50 V C7 00 p R9 k9 - STEVAL-IPMnMN 0 9 UC 8 TSV99 R0 k0 R8 k9 C6 0 n R k DB6 - Rev page 5/8

6 STEVAL-IPMnMN Figure 5. STEVAL-IPMnMN circuit schematic (5 of 5). V SW9 5 V H/Z H/B H/A GND./5 V J5 5 5 Encoder/Hall. V 5 V Ha l l / E n c o d e r SW0 R k7 SW R9 k C 00 n R5 k7 SW C7 0 p R0 k7 SW5 R k7 R k7 M_phase_A M_phase_B M_phase_C C 00 n C 00 n SW6 R7 k SW R8 k C5 0 p C6 0 p R6 k7 SW DB6 - Rev page 6/8

7 STEVAL-IPMnMN Revision history Table. Document revision history Date Version Changes 05-Sep-07 Initial release. 07-May-08 Updated title in cover page Updated Section Features Updated Section Description DB6 - Rev page 7/8

8 STEVAL-IPMnMN IMPORTANT NOTICE PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. 08 STMicroelectronics All rights reserved DB6 - Rev page 8/8