UM1746 User manual. 500 W fully digital AC-DC power supply based on the STM32F334 microcontroller. Introduction

Transcription

1 User manual 500 W fully digital AC-DC power supply based on the STM32F334 microcontroller Introduction This user manual describes the basic procedure to correctly operate the 500 W digital power supply evaluation board, order code STEVAL-ISA147V2. This system consists of a semi-bridgeless PFC circuit and an isolated DC-DC converter used to deliver 500 W at 12 V DC. The system operates with input voltages in the range of 95 V to 265 V AC and can be supplied both at 50 Hz and 60 Hz. The board is equipped with a fully digital control algorithm based on two microcontrollers from the STM32 family. The PFC control has been implemented on an STM32F051K8 while the LLC half-bridge control has been implemented on an STM32F334C8 microcontroller. The LLC converter is provided with a synchronous rectification (SR) stage used to achieve high conversion efficiency. A photo of the STEVAL-ISA147V2 500 W power supply board is shown in Figure 1. Figure W digital power supply system with 12 V output June 2014 DocID Rev 1 1/12

2 Contents UM1746 Contents 1 Evaluation board overview Testing the board Test results Revision history /12 DocID Rev 1

3 Evaluation board overview 1 Evaluation board overview The STEVAL-ISA147V2 is a 500 W dual-stage converter digitally controlled by two 32-bit STM32 microcontrollers. An overview of the power supply architecture is shown in Figure 2. Figure 2. Block diagram of the STEVAL-ISA147V2 system architecture The first block, from left to right, is the EMI filter. This section of the circuit is highlighted in Figure 3. A two-stage topology has been implemented. Figure 3. Two-stage EMI filter DocID Rev 1 3/12 12

4 Evaluation board overview UM1746 The EMI filtering stage is directly connected to the input of the semi-bridgeless PFC circuit. The PFC circuit is highlighted in Figure 4. It consists of two inductors, L1 and L2, two MOSFETs Q1 and Q2, and two rectifying diodes, D7 and D8. D9 and D13 are used as precharge diodes and conduct current only when the AC voltage is applied to charge the four 100 uf, 450 V DC bus capacitors shown in the bottom-right part of the highlighted area in Figure 4. D12 and D10 are used to keep the negative phase connected to the PFC ground and improve EMI filtering. These two diodes conduct part of the current returning to the source during operation. Figure 4. PFC circuit T4 and T5 are the two current sensing transformers used to sense the drain current of each MOSFET. The LLC stage performs voltage step-down using an HF transformer with a primary-tosecondary turns ratio chosen to maintain good efficiency and regulation in the entire operating range. The transformer is supplied with a square wave voltage generated by the primary side active switches. On the secondary side this voltage waveform is rectified and then smoothed by the output filter. While on the primary side switching losses are reduced thanks to zero voltage switching (ZVS), while on the secondary side synchronous rectification (SR) is used to ensure low conduction losses. The overall effect of these design choices is high system efficiency. The LLC section of the power supply system is highlighted in Figure 5. This section consists of the two MOSFETs of the half-bridge Q12 and Q3, the high frequency transformer T1, the resonant capacitors C84 and C45, the synchronous rectifier MOSFETs Q6, Q7, Q13, Q14. Although it is possible to mount up to 3 devices for each side of the rectification circuit, only two devices per side are used and soldered on the PCB. The output filter capacitors are shown in the upper-right part of the highlighted area in Figure 5. The driver of the half-bridge is an L6491D, U8, which is mounted close to Q12 and Q3. The driver of the synchronous rectification devices is a PM8834, IC2, which is mounted on the bottom of the PCB. U10 and U9 are two opto-isolators used to supply the gate signals generated by the STM32F30x to Q12 and Q3 through the driver U8. U11 and U12 are two 4/12 DocID Rev 1

5 Evaluation board overview additional opto-isolators used for bidirectional communication between the PFC microcontroller, U13, and the LLC microcontroller U14. Figure 5. LLC converter P4 and P5 are the two connectors used to program U13 and U14, respectively. The two microcontrollers can be programmed using IAR Embedded Workbench for ARM ver and a suitable debugger/programmer such as IAR J-Link or STMicroelectronics ST-Link. The auxiliary power supply section implemented with a VIPER27H circuit is highlighted in Figure 6. Figure 6. Auxiliary power supply circuit The main specifications of the system are given in Table 1. DocID Rev 1 5/12 12

6 Evaluation board overview UM1746 Table W AC-DC converter specifications Parameter Input AC voltage Input AC frequency Output voltage Output current PFC output voltage Output power PFC switching frequency DC/DC switching frequency: HF transformer isolation Peak efficiency Cooling Input short-circuit protection Input overload protection Input under/overvoltage Input under/overfrequency Bus DC under/overvoltage Output under/overvoltage Overtemperature protection Value 95 V AC up to 265 V AC 45 Hz up to 65 Hz 12 V DC 42 A 430 V DC 500 W 60 khz 70 khz up to 115 khz (burst mode above) 4 kv 230 V AC Natural convection up to 300 W; Forced above 10 A fuse Managed by STM32F051K8 Managed by STM32F051K8 Managed by STM32F051K8 Managed by STM32F051K8 Managed by STM32F334C8 Managed by STM32F051K8 (PFC) and STM32F334C8 (LLC) The converter accepts universal input voltage and produces a 12 V regulated output. The continuous power rating of the unit is 500 W. Natural convection is used up to 300 W. Above this power level a cooling fan is activated to provide forced air cooling. The ambient operating temperature range is 0 to 50 C. The intermediate high-voltage DC bus is regulated at 430 V by the PFC which draws sinusoidal input current from the AC input maintaining high power factor and low current total harmonic distortion (THD%). The LLC circuit converts this high DC voltage to low DC voltage proving isolation (4 kv) by means of an HF transformer and high efficiency thanks to ZVS. Input and output current and voltage protection are also provided together with overtemperature protection. 6/12 DocID Rev 1

7 Testing the board 2 Testing the board The board can be easily tested up to 500 W and across the operating input voltage and frequency range. A list of equipment that can be used to perform functional and efficiency testing is provided below: 750 VA programmable AC source 12 V/42 A DC electronic load Power analyzer Digital oscilloscope The programmable AC source must be connected to JP1 as shown in Figure 7, where the connection of line, neutral and earthing cables is shown. Figure 7. Connection of the AC cables The output load must be connected to P6 (Figure 8), using the cable provided with the board and shown in Figure 9, or another suitable cable capable of carrying the desired load current (42 A max). A cooling fan is also provided with the board and should be activated by the user when the power output of the board is higher than 300 W. The fan connects to P7, a dedicated 12 V connector shown in Figure 10. Once the input power supply (95 V to 265 V AC, 45 Hz to 65 Hz) and output load (12 V, 0 A to 42 A) are connected, the power supply is ready to start. As soon as the input voltage is above 58 V the auxiliary power supply starts and powers the microcontrollers, drivers and signal conditioning circuitry. In this operating condition the PFC and LLC converter are idle. Since the microcontrollers are supplied, the programming cable and debugger can be connected either to P4 or P5 to re-flash the microcontroller if/when necessary. If the input voltage is above 95 V AC the PFC starts. The LED D24 blinks 3 times and the DC bus is charged to 430 V. Once the DC bus is charged, a serial message is sent from the DocID Rev 1 7/12 12

8 Testing the board UM1746 PFC microcontroller U13 to the LLC converter microcontroller U14, which enables the modulation of the LLC half-bridge devices and SR devices. The output voltage will ramp up from 0 to 12 V. Figure 8. Output connector P6 for load connection Figure 9. Cable for output load connection (42 A max) 8/12 DocID Rev 1

9 Testing the board Figure 10. Connection of the cooling fan to P7 connector DocID Rev 1 9/12 12

10 Test results UM Test results The test was conducted with open frame at an ambient temperature of 25 C. The cooling fan was activated above 300 W and supplied by an external 12 V power supply. Therefore, the test results do not account for cooling fan power consumption. All test results were collected using a Voltech PM6000 universal power analyzer. An electronic DC load was used to draw constant current at every testing point. The testing results are summarized in Table 2 and Table 3. Table 2. Test results for 120 V AC input operation V IN (V) I IN (A) P IN (W) V OUT (V) I OUT (A) P OUT (W) Efficiency (%) PF THD% , Table 3. Test results for 230 V AC input operation V IN (V) I IN (A) P IN (W) V OUT (V) I OUT (A) P OUT (W) Efficiency (%) PF THD% /12 DocID Rev 1

11 Revision history 4 Revision history Table 4. Document revision history Date Revision Changes 19-Jun Initial release. DocID Rev 1 11/12 12

12 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America 12/12 DocID Rev 1