Dim. Method. Parameter Min. Typ. Max. Unit Remark. Input Current AC 120V, 100% Load. Efficiency AC V,100% Load

Transcription

1 PIFN-H030A Flat 30W LED Driver 30V - 42V / 0.66A / 27.72W(Max) Features Mechanical Outline Dimming Method: 1-10V Dimming (1V=10%) (Metal Case) - 280(L) 31(W) 26.8(H)mm Constant Current Control Active Power Factor Correction Protection : OVP and SCP UL 8750, UL 1310, CSA C22.2 No , Class 2 Wiring Output Safety Certifications Approved FCC part 15, Class B verification RoHS Compliant Electrical Specifications Output [W] Output [Vdc] Output [A] Input [Vac] Dim. Method PF Efficiency [%] Mechanical Outline [LxWxH mm] V >0.9 Min Input Specifications Input Voltage (Nominal) Vac Input Current AC 120V, 100% Load Input Wattage AC 120V, 100% Load Nominal Input Frequency - 50/60 - Hz Efficiency AC V,100% Load Power Factor CTQ AC V,100% Load THD AC V,100% Load Inrush Current Measured Value

2 Output Specifications CAUTION 1) Output Voltage V LG innotek LED Modules Only Output Current Range A(Idc) Fixed Current Output Current Tolerance % Dimming Output Dimming Current Range % 1-10V Dimming CAUTION 2) CTQ Output Dimming Current Min A(Idc) 1V Dimming Output Ripple Current % Flicker = 100 x (Max Min)/(Max + Min) LED Module : LLFML51-26L series Output Power W Start-up Time - - 1, % Dimming Protection Functions Output Over Voltage Protection V Auto Recovery Output Short Circuit Protection A Auto Recovery CAUTION 1) : This product is optimized for LG innotek LED Module (LLFML51-26L series) Contact the manufacturer when using other LED modules. CAUTION 2) : Recommended high-speed ON / OFF cycle can not be faster than 2 seconds ON, 2 seconds OFF Flicker may occur when lighting up at faster ON / OFF

3 Environmental Specifications Temperature Operation Ta - - Tc Storage Ta Humidity Operation % - Storage % - Life time Tc=72.5 / AC 120V~277V Life Time Curve Standards Parameter Condition Remark Safety Standards EMI / RFI Standards Design to meet the requirements as follows ; - UL8750, UL1310, CSA C22.2 No Class 2 Wiring Output Design to meet the requirements as follows ; - FCC part 15, Class B verification

4 Dimming Control (1-10V Dimming) Output Current [ma] Dimming Voltage [V] Driving current for Dimmer Dimming 1-10V Analog Class 2 Wiring Dimming Range Minimum Output Current (A) 10% ~ 100% 0.09 Other Comments Dimming source current : Max 850uA (±3%) Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment.

5 Mechanical Outline 1. Case Dimension (Unit: mm) 2. Connector description 2.1 AC Connector (CN101) Pin No. Name Color 1 Live Black 2 Neutral White 2.2 DC Connector (CN301) Pin No. Name Color 1 VLED+ Red 2 VLED- Black 3 DIM+ Purple 4 GND/DIM- Gray

6 3. Installation Guide The Wire with O-ring should be jointed with Luminaire Fixture. Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment.

7 Datasheet Revision History Change Date Rev. No. Description of Change Remark Initial Release Output characteristics update Output characteristics update Output characteristics update Operation Temperature characteristics update - Life Time Curve update PCB Revision is updated MP 1.0 version. - Output characteristics update Adding caution content to the output specification