Models Adjustable Output Current Range. HUK-096SxxxDV. 96W Programmable Driver for High Bay

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Models Adjustable Output Current Range. HUK-096SxxxDV. 96W Programmable Driver for High Bay"

Transcription

1 Features Inventronics patented metal case (Patent NO.: X) High Efficiency (Up to 92.0%) Full Power at Wide Output Current Range (Constant Power) 010V/10V PWM Dimmable Input surge protection: 4kV lineline, 6kV lineearth AllAround Protection: OVP, SCP, OTP Waterproof (IP67) SELV Output Suitable for Independent Use 5 Years Warranty Description The series is a 96W, constantcurrent, programmable IP67 LED driver that operates from Vac input with excellent power factor. It is designed in vertical type and specially created for bay lighting. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure troublefree operation, protection is provided against input surge, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range FullPower Current Range (1) Default Output Current Input Voltage Range(2) Output Voltage Range Max. Typical Output Efficiency Power (3) Power Factor 120Vac 220Vac Model Number mA mA 700 ma 90~305 Vac/ 48~137Vdc 127~250 Vdc 96 W 92.0% ~305 Vac/ mA mA 2100 ma 24 ~ 69Vdc 127~250 Vdc 96 W 91.0% (4) 90~305 Vac/ mA mA 2800 ma 14 ~ 39Vdc 127~250 Vdc 96 W 89.0% (4) Notes: (1) Output current range with constant power at 96W (2) Certified input voltage range: Vac or Vdc (except CCC, PSE, KS and BIS) (3) Measured at full load and 220Vac input (see below General Specifications for details). (4) SELV Output. 1 / 15

2 IV Operation Area Output Voltage(V) 60%Load Input Specifications Parameter Min. Typ. Max. Notes Input Voltage 90 Vac 305 Vac 127~250 Vdc Input Frequency 47 Hz 63 Hz Leakage Current 0.70 ma IEC605981; 240Vac/ 60Hz Input AC Current Inrush Current(I 2 t) 1.20 A 2 s 0.95 A Measured at full load and 120 Vac input A Measured at full load and 220 Vac input. At 220Vac input, 25 C cold start, duration=344μs, 10%Ipk10%Ipk. See Inrush Current Waveform for the details. 2 / 15

3 Input Specifications (Continued) Parameter Min. Typ. Max. Notes PF 0.9 THD 20% THD 10% At Vac, 5060Hz, 60%100% Load (5896W) At Vac, 5060Hz, 75%100% Load (7296W) Output Specifications Parameter Min. Typ. Max. Notes Output Current Tolerance 5%Ioset 5%Ioset At full load condition Output Current Setting(Ioset) Range Output Current Setting Range with Constant Power Total Output Current Ripple (pkpk) Output Current Ripple at < 200 Hz (pkpk) 70 ma 140 ma 245 ma 700 ma 1400 ma 2450 ma 1050 ma 2100 ma 3500 ma 1050 ma 2100 ma 3500 ma 5%Iomax 10%Iomax At full load condition. 20 MHz BW 2%Iomax Startup Overshoot Current 10%Iomax At full load condition No Load Output Voltage 160 V 89 V 49V At full load condition. Only this component of ripple is associated with visible flicker. Line Regulation ±5% Measured at full load Load Regulation ±5% Turnon Delay Time Temperature Coefficient of Ioset 1.0 s 0.5 s Note: All specifications are typical at 25 C unless otherwise stated. Measured at 120Vac input, 60%100% Load Measured at 220Vac input, 60%100% Load 0.06%/ C Case temperature = 0 C ~Tc max 3 / 15

4 General Specifications Parameter Min. Typ. Max. Notes Efficiency at 120 Vac input: Io= 700 ma Io=1050 ma Io=1400 ma Io=2100 ma Io=2450 ma Io=3500 ma Efficiency at 220 Vac input: Io= 700 ma Io=1050 ma Io=1400 ma Io=2100 ma Io=2450 ma Io=3500 ma Efficiency at 277 Vac input: Io= 700 ma Io=1050 ma Io=1400 ma Io=2100 ma Io=2450 ma Io=3500 ma 87.5% 87.5% 86.5% 87.0% 84.5% 84.5% 89.5% 90.0% 88.5% 89.0% 87.0% 86.5% 89.5% 90.0% 89.0% 89.0% 87.5% 87.0% MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w 89.5% 89.5% 88.5% 89.0% 86.5% 86.5% 91.5% 92.0% 90.5% 91.0% 89.0% 88.5% 91.5% 92.0% 91.0% 91.0% 89.5% 89.0% 422,000 Hours 108,000 Hours 40 C +90 C Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at full load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at 220Vac input, 80%Load and 25 C ambient temperature (MILHDBK 217F) Measured at 220Vac input, 80%Load and 70 C case temperature; See lifetime vs. Tc curve for the details 40 C +75 C Case temperature for 5 years warranty Storage Temperature 40 C +85 C Humidity: 5%RH to 100%RH Dimensions Inches (L W H) Millimeters (L W H) Net Weight 1140 g Note: All specifications are typical at 25 C unless otherwise stated. 4 / 15

5 Dimming Specifications Parameter Min. Typ. Max. Notes Absolute Maximum Voltage on the Vdim (+) Pin Source Current on Vdim (+)Pin Dimming Output Range Recommended Dimming Range for 010V 20 V 20 V 200 ua 300 ua 450 ua Vdim(+) = 0 V 10%Ioset Ioset 70 ma 140 ma 245 ma Ioset PWM_in High Level 10V PWM_in Low Level 0V PWM_in Frequency Range 200 Hz 2 KHz PWM_in Duty Cycle 0% 100% 700mA Ioset 1050mA 1400mA Ioset 2100mA 2450mA Ioset 3500mA 70mA Ioset < 700mA 140mA Ioset < 1400mA 245mA Ioset < 2450mA 0 V 10 V Default 010V dimming mode. Safety &EMC Compliance Safety Category Standard CE EN , EN CCC GB , GB KS KS C 7655 EMI Standards EN 55015/GB (1) EN /GB EN EMS Standards EN EN EN EN EN EN EN EN Notes Conducted emission Test &Radiated emission Test Harmonic current emissions Voltage fluctuations & flicker Notes Electrostatic Discharge (ESD): 8 kv air discharge, 4 kv contact discharge RadioFrequency Electromagnetic Field Susceptibility TestRS Electrical Fast Transient / BurstEFT: level 3, criteria A Surge Immunity Test: AC Power Line: line to line 4 kv, line to earth 6 kv Conducted Radio Frequency Disturbances TestCS Power Frequency Magnetic Field Test Voltage Dips Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. 5 / 15

6 Derating Lifetime vs. Case Temperature Inrush Current Waveform 6 / 15

7 Efficiency vs. Load (lo=700ma) (lo=1050ma) (lo=1400ma) (lo=2100ma) (lo=2450ma) (lo=3500ma) 7 / 15

8 Power Factor Total Harmonic Distortion Protection Functions Parameter Over Temperature Protection Short Circuit Protection Over Voltage Protection Notes Decreases output current, returning to normal after over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. 8 / 15

9 Dimming 010V Dimming The recommended implementation of the dimming control is provided below. Implementation 1 Notes: 1. The dimmer can also be replaced by an active 010V voltage source signal or passive components like resistors and zener. 2. If 010V dimming is not used, Dim + should be open. 10V PWM Dimming Implementation 2 Notes: 1. If PWM dimming is not used, Dim + should be open. 9 / 15

10 Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRGMUL2 MultiProgrammer datasheet for details. Installations Assembly Method Option 1 Option 2 Option 3 Option 4 Product Type Center Wire Feed Outside Wire Feed Part Numbers for Accessories Upper Bracket Bottom Bracket Hook / Eye Bolt BRKUPR00 BRKUPR00 BRKUPR01 BRKUPR01 BRKBTM00 BRKBTM01 BRKBTM00 BRKBTM01 HKKD1500 HKKD1500 BLTM1200 BLTM1200 Product Appearance 10 / 15

11 Installations (Continued) Installation Type Caution: 1. Complete visual inspection prior to assembly to insure driver is received in proper condition. 2. Mounting accessory (hook, ring, etc.) has to be tightened completely. After mounting accessory (hook, ring, etc.) is installed an M3 set screw should be secured in the open location on the driver collar. 3. Maximum weight of combined luminaire/driver assembly should not exceed 20Kg. Mechanical Outline INPUT(VDE H05RNF 3*1mm 2 7.2) OUTPUT(VDE H05RNF 2*1mm 2 6.8) AC/L (BROWN) AC/N (BLUE) GND (YELLOW/GREEN) GRAY PURPLE BLACK/WHITE Tc V+ (BROWN) V (BLUE) DIMMING WIRE(VDE 3*0.5mm 2 6.3) PROJ: Unspecified toleranc:±1 11 / 15

12 Optional Brackets BRKUPR00 BRKUPR01 PROJ: Unspecified tolerance:±1 Unspecified tolerance:±1 12 / 15 PROJ:

13 BRKBTM00 PROJ: Unspecified tolerance:±1 BRKBTM01 PROJ: Unspecified tolerance:±1 13 / 15

14 Optional Metal Parts HKKD1500 BLTM1200 PROJ: Unspecified tolerance:±1 DN15 PROJ: Unspecified tolerance:±1 M12*1.75 Note: The brackets are to be installed with drivers for field application. Please refer to BRK UPR(BTM)xx datasheet for details. RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products. 14 / 15

15 Revision History Change Date Rev. Description of Change Item From To A Datasheets Created / / 15 / 15