SAMSUNG ELECTRO-MECHANICS CO., LTD

Transcription

1 Model Name : Features : ㅡ Suitable for LED lighting application ㅡ UL8750, UL1310 Class 2 ㅡ For use in Dry and Damp Location ㅡ Full-protection provided: OCP/OVP/OTP/SCP ㅡ 0-10V Dimming Control ㅡ IP67 ㅡ 5-years warranty

2 Electrical specification No. Item Min Typ Max Unit Remark 1 Nominal Input Voltage Vac 2 Wide Input Voltage Vac 3 Maximum Input Current 1.5 Arms 4 Nominal Input Frequency Hz 5 Wide Input Frequency Hz 6 Power Factor (PF) 0.9 1) 7 Total Harmonic Distortion (THD) 20 % 1) 8 Inrush Current NEMA410 10) 9 Earth Leakage Current 500 μa 10 Insulation Resistance 100 MΩ 500Vdc between Input & Output 11 Output Voltage Vdc 12 Output Current 1,330 1,400 1,470 Aging, 1) 13 Output Current Ripple 210 ma 1) 14 Output Peak Current 2,800 ma 1) 15 Output Aging Current Differential ±70 Aging 16 Turn-on Delay 1,500 ms 2) 17 Electrical Efficiency 85 % 3) 18 12V Output Voltage Vdc 12V Max and No Load, 1) 19 12V Output Current ma 20 Dimming Control 0 10 Vdc 4) 21 Output Over Voltage Protection Vdc Auto-recovery 22 Output Short Circuit Protection Auto-recovery or Latch-off 23 12V Output Short Circuit Protection Auto-recovery or Latch-off 24 Over-temperature Protection 105 Auto-recovery or Latch-off 25 Case Temperature (Tc) Storage Temperature Operating Temperature Differential Mode (Line to Line) -4 4 kv 5) 29 Common Mode (Line to Ground) -6 6 kv 5) 6) 30 Contact Discharge Test Voltage -4 4 kv 7) 31 Air Discharge Test Voltage -8 8 kv 7) 8) 32 Vibration 3 G 33 Humidity 90 % 34 Dielectric Input to Output 1,554 Vac Apply for 1 minute 35 Withstand Input to Case 1,554 Vac 9) 36 Voltage Output to Case 500 Vdc

3 Application Notes 1) Test Condition: 100/277Vac 50/60Hz Input, Typical LED Load, Ambient Temp. 25 2) Test Condition : Input 240Vac 60Hz, Typ. Load, Cold start 3) Test Condition: 240Vac Input, 30min Aging, LED Typ. Load, 12V Output no Load 5) Surge Specification above is higher than EN (Differential 1kV, Common 2kV ) 6) The metal case of the LED driver must be connected with F.G 7) ESD Specification above meets EN Requirements (Contact 4KV, Air 8KV) 8) The metal case of the driver should be grounded. 9) Determined by Paragraph , UL1310 or Paragraph 8.4.2, UL8750, EN , EN ) Input 120Vac, < 192Apeak, < 1.2ms, < 74A2sec Dimming Curve 100% Dimming ratio 10% 1V Dimmer Voltage 10V Safety Standards Including safety requirements above, the LED driver complies with the following safety standards: No. Item Description 1 UL8750, UL1310, UL1012 UL Safety Standards (Class 2, Dry and Damp Location) 2 FCC Part 15, Class B Conducted and Radiated Emission Test 3 IEC Harmonic current emissions: Class C 4 IEC Voltage Fluctuations and Flicker 5 IEC Electrostatic Discharge (ESD): Contact 4KV, Air 8KV 6 IEC Radio-frequency Electromagnetic Fields 7 IEC Electrical Fast Transients (EFT Level 2) 8 IEC Surges: Differential 1kV, Common 2kV 9 IEC Injected Currents 10 IEC Power Frequency Magnetic Fields 11 IEC Voltage Dips and Short Interruptions

4 Life Time vs Tcase Life Time [Hrs] Tc [ ] Remark) LED Driver has a rated lifetime of 50,000 Tc 70 Efficiency(%) Efficiency (%) Input Voltage(Vac) Load(Vo=32V) Load(Vo=28V) Load(Vo=36V)

5 Power Factor PF Input Voltage (Vac) Load(Vo=32V) Load(Vo=28V) Load(Vo=36V) THD(%) THD [%] Input Voltage (Vac) Load(Vo=32V) Load(Vo=28V) Load(Vo=36V)

6 Mechanical Specification Enclosure Size Unit Width Length Height mm inch Mounting Length Overall Length Case Material : Aluminium

7 Wiring Diagram INPUT OUTPUT LIVE LED DRIVER LED + LED - +12V C O N NEUTRAL DIM+ C O N DIM-/GND Remark) Output wiring specifications can be changed. Rating Label Drawing